Buildex 2003 cat

Building Ideas That Work ®

29

27

31

47

41

33

45

METAL R OOF END CAP FLASHING APPLICA TIONS REPORT NO. 02715

P I P E F L A S H I N G A P P L I C A T I O N S REPORT NO. 02714

R O O F F L A S H I N G A P P L I C A T I O N S REPORT NO. 02716

P O LY M E R B A S E D E I F S A P P L I C A T I O N S

D RY WA L L A N C H O R A P P L I C A T I O N S REPORT NO. 02721

L IGHT/MEDIUM DUTY MASONR Y APPLICA TIONS REPORT NO. 02717

E X T E R I O R W O O D A P P L I C A T I O N S REPORT NO. 02723

• DEK-CAP ™ STANDING SEAM ROOF END CAP FLASHING

• DEKTITE ® AND RETROFIT DEKTITE ®

• EPDM AND SILICONE FOR 1/4” TO 24” PIPES

• FLASHDEK ® FLEXIBLE HYPALON ® SYSTEM

• GRIDMATE ™ PB EIFS MECHANICAL FASTENERS

• E-Z ANCOR® ZINC, PLASTIC PLUS™, E-Z TOGGLE™, E-Z ANCOR LITE™ ,E-Z MINI ANCOR®, E-Z EST™

• 3 /16 ' ' AND 1/4 ' ' DIAMETER TAPCON ® ANCHORS• HEX AND FLAT HEADS

• #6, #7, #8 AND #10 DIAMETER DEC-KING ® SCREWS

BX

43 C E M E N T B O A R D A P P L I C A T I O N S REPORT NO. 02722

• HI -LO ® AND S-12 ® ROCK-ON ™ SCREWS/BACKER-ON ™ SCREWS• COUNTERSINKING WAFER HEAD

35 L IGHT/MEDIUM DUTY MASONR Y APPLICA TIONS

• 1 /4 ' ' DIAMETER MAXI-SET TAPCON ® ANCHORS• 5/16" ACROSS FLATS HEX WITH 5/8" DIAMETER FLANGE

49 P O LY M E R M O D I F I E D E I F S A P P L I C A T I O N S

• GRIDMATE ™ EIFS MECHANICAL FASTENERS

37 EXTERIOR MASONRY APPLICA TIONS REPORT NO. 02719

• 1 /4 ' ' DIAMETER SCOTS ® TAPCON ® ANCHORS• 300 SERIES STAINLESS STEEL HWH INTEGRAL WASHER SYSTEM.

REPORT NO. 02724

REPORT NO. 02725

25 M E TA L - T O - W O O D A P P L I C A T I O N S REPORT NO. 02712

• #9 AND #12 DIAMETER GIMLET POINT SCOTS ® TRUGRIP ™

39 CORROSIVE ENVIRONMENT MASONRY APPLICA TIONS REPORT NO. 02720

• 1 /4 ' ' DIAMETER 410 STAINLESS STEEL TAPCON ® ANCHORS• HEX AND FLAT HEADS

REPORT NO. 02718

HEAD

Proper head style choice will ensurestability during driving, proper clamping and desired finishedappearance.

THREAD FORM AND DIAMETER

The correct choice of thread formand diameter optimizes low in-stallation torque with high pulloutstrength.

TEKS® FASTENER FEATURES

FINISH

Platings and coatings provide lubricity during drilling and tapping aswell as corrosion resistance.

PILOT SECTION

The unthreaded portion of the pointassures that the drilling of the steel iscompleted before the threads begintapping into the drilled hole.

POINT

The point is designed to efficientlyremove material and precisely sizethe hole for the thread.

HEAD

THREADS

PILOT SECTION(WHEN NECESSARY)

FLUTE

POINT

FASTENER DESCRIPTION AND BREAKDOWNExample:

10 - 16 x 3/4" HWH TEKS/3Nominal Threads Screw Head Drill Point

Screw Size Per Inch Length Style Type

NOMINAL SCREW SIZES

THREAD DECIMAL

DIAMETER EQUIVALENT

#6 .140#7 .150#8 .160#9 .180

#10 .190#11 .200#12 .210#13 .230#14 .2401/4 .250#17 .286

STEEL GAUGE CHART

COMMONSHEET STEEL

DECIMAL EQ.GAUGES INCHES MM

30 .012 .3028 .015 .3826 .018 .4524 .024 .6122 .030 .7620 .036 .9118 .048 1.2116 .060 1.5214 .075 1.9012 .105 2.651/8 .125 3.1810 .134 3.42

3/16 .187 4.771/4 .250 6.361/2 .500 12.72

4

MAT

ERIA

LTH

ICKN

ESS

(INCH

ES)

.500

.400

.300

.200

.100

.030

.0

2.4mm

.095

.018

.45mm

#10

2.4mm

.095

.018

.45mm

#12

2.4mm

.095

.018

.45mm

1/4

2.50mm

.100

.036

.91mm

#8

5.3mm

.210

.036

.91mm

#12

4.17mm

.175

.036

.91mm

#10

5.3mm

.210

.036

.91mm

#12

5.3mm

.210

.036

.91mm

1/4

.1253.18mm

#12

.1253.18mm

1/4

9.51mm

.375

.1253.18mm

#12

12.72mm

.500

.1253.18mm

#12

12.72mm

.500

.1253.18mm

1/4Teks/1 Teks/2 Teks/3 Teks/4 Teks/4.5 Teks/5

*Drill & tap capacities may vary with special feature designs.Refer to product reports for specifics.

6.36mm

.250

Screw SizePoint

DRILL AND TAP MATERIAL THICKNESS CHART

6.36mm

.250

Driv-Tru ™

HWH SOCKET SYSTEM

PartNumber Description Applications

1591910 Driv-Tru Socket All 1/4'' across flats HWH fasteners



Selector Guide

LIG

HT

DU

TY

AP

PLIC

ATIO

NS

PR

OD

UC

TR

EP

OR

TN

O.02701

Product FeaturesSharp convex drill point has precise cuttingedges to improve drill performance with less effort.

Non-walking point provides fast materialengagement.

Unique point to thread design extrudes the metalpreventing stripout.

Point to thread design maximizes pullout performance and minimizes backout.

Four head styles available to handle variousapplications.

Climaseal® finish provides excellent corrosion resistance and lower tapping torque.

Preferred most b y electrical, decking, HVAC and

metal b uilding contractor s.

TEKS ®

Self-Drilling F astener s

Product SpecificationsDiameter #6, #8, #10, #12 and 1/4Thread Form 6-20

8-1810-16, 10-2412-141/4-14

Head Style #6: #2 Phillips Pan#8: 1/4” HWH; #2 Phillips Pan#10: 5/16'' HWH; 5/16'' HWH with Serrations;

#2 Phillips Pan; #2 Phillips Oval#12: 5/16'' HWH1/4: 5/16'' HWH

Drill P oint Teks 1 Teks 2 Teks 3

Finish #6, #8, Electro-zinc#10, #12 and 1/4 Climaseal®

Head StylesHex Washer Hex Oval Head

Hex Washer Head Pan Head with Serrations

Appr ovals and ListingsFactory Mutual (J.I. 2 X 942 AM), ICBO 3056,Steel Deck Institute.

ApplicationsStitch roof deck and wall panel sidelaps.HVAC, electrical trim accessories to steel framing.Residential steel frame construction.

Brick ties to steel framing.Track to stud and stud splicing.Hat channel to stud.

Corr osion Resistance . . . Climasea l ®

Kesternic h Results (DIN 50018, 2.0L) Salt Spra y Results (ASTM B117)• 30 Cycles - 10% or less red rust • 720 hours - 10% or less red rust

Corr osion Resistance . . . Electr o-zincKesternic h Results (DIN 50018, 2.0L) Salt Spra y Results (ASTM B117)• 3 Cycles - 5% or less red rust • 48 hours - 5% or less red rust

5

Installation GuidelinesA standard screwgun with a depth sensitive nosepiece should beused to install Teks. For optimal fastener performance, thescrewgun should be a minimum of 4 amps and have a RPMrange of 0-2000.Adjust the screwgun nosepiece to properly seat the fastener.New magnetic sockets must be correctly set before use.Remove chip build-up as needed.

The fastener is fully seated when the head is flush with the work surface.Overdriving may result in torsional failure of the fastener orstripout of the substrate.The fastener must penetrate beyond the metal structure a minimum of 3 pitches of thread.

Dia.#6#8

#121/4

Pt.221311

26278294398

–432511

24466496584455703849

22526560659526753885

20758740884728

10181244

18845

10601374126614521764

16–––

1540––

14–––

1552––

TEKS ®

SELF-DRILLING FASTENERS

SelectorGuide

Performance Data

Dia. Pt.221311

26120119148124159208

24183193241208261329

22248265311266338428

20296298357299390562

18471491565499649800

16679703826708908

1151

14847959

1111967

1259–

12––

179614741949

–

Fastener Steel Gaug e

PULLOUT VALUES (average lbs. ultimate)

Fastener Steel Gaug e (lapped)

SHEAR VALUES (average lbs. ultimate)

#10

12

.105''

14

.075''

16

.060''

18

.048''

20

.036''

22

.030''

24

.024''

26

.018''

Gauge No.

Decimal Equivalent

SHEET STEEL GAUGES

Teks®, Climaseal® and Building Ideas that Work® are trademarks ofITW Buildex and Illinois Tool Works Inc.

The values listed are ultimate averages achieved under laboratory conditions and apply to Buildex manufactured fasteners only. Appropriate safety factors should be applied to these values for designpurposes.

Product Report No. 02701

Part Head Drill Drill & Tap Max. Material Bo x Number Description Style Point Capacity Attac hments Qty Applications

1208200 6-20 x 3/8'' Pan #2 .036-.100 .100 20,0001210200 8-18 x 1/2'' Pan #2 .036-.100 .205 10,0001213200r 8-18 x 3/4'' Pan #2 .036-.100 .455 10,0001218200 8-18 x 1'' Pan #2 .036-.100 .705 8,0001196200r 8-18 x 1/2'' HWH #2 .036-.100 .205 10,0001199200 8-18 x 5/8'' HWH #2 .036-.100 .330 10,0001200200r 8-18 x 3/4'' HWH #2 .036-.100 .455 10,0001202200 8-18 x 1'' HWH #2 .036-.100 .705 8,0001204200 8-18 x 1-1/2'' HWH #2 .036-.100 1.205 4,0001107000 10-16 x 3/4'' HWH #1 .018-.095 .220 5,0001109000 12-14 x 3/4'' HWH #1 .018-.095 .205 5,000 1399000 1/4-14 x 7/8'' HWH #1 .018-.095 .380 5,0001398000 10-16 x 1/2'' Pan #3 .036-.175 .150 10,0001541000 10-16 X 5/8'' Pan #3 .036-.175 .200 5,0001224000 10-16 x 3/4'' Pan #3 .036-.175 .325 5,0001542000 10-16 x 3/4'' Oval #3 .036-.175 .325 5,0001397000r 10-16 x 1/2" HWH #3 .036-.175 .150 5,0001127000 10-16 x 5/8" HWH #3 .036-.175 .200 5,0001128000r 10-16 x 3/4" *HWH #3 .036-.175 .325 5,000 1129000r 10-16 x 1" HWH #3 .036-.175 .575 5,0001544000 10-16 x 1'' Oval #3 .036-.175 .575 5,0001545000 10-16 x 1'' Pan #3 .036-.175 .575 5,0001130000 10-16 x 1-1/4" HWH #3 .036-.175 .825 4,0001546000 10-16 x 1-1/4'' Oval #3 .036-.175 .825 5,0001131000 10-16 x 1-1/2" *HWH #3 .036-.175 1.075 3,0001550000 10-24 x 3/4'' HWH #3 .036-.175 .323 5,0001551000 10-24 x 1'' HWH #3 .036-.175 .575 5,000

†1786200 10-24 x 5/8'' **HWH #2 .036-.175 .200 5,000†1707200 10-16 x 3/4'' **HWH #3 .036-.175 .323 5,000

1821200 10-16 X 3/4'' **HWH #3 .036-.175 .323 5,000

• HVAC, electrical trim accessoriesto steel framing.

• Residential steel frameconstruction.

• Track to stud.• Hat channel to stud.• Stud splicing.

• Clips, duct straps, brick ties oraccessories to steel framing.

• Stitching roof deck, wall panelsidelaps or duct work.

#6#8

#10-16

#121/4

Fastener(dia-tpi)

6-208-18

10-1610-2412-141/4-14

Tensile(lbs. min.)

128515451936270227784060

Shear (avg. lbs. ult.)

75010001400150020002600

Torque(min. in. lbs.)

2542616592

150

FASTENER VALUES

1349 West Bryn Mawr AvenueItasca, Illinois 60143630/595-3500 FAX: 630/595-3549www.itwbuildex.com ©2002 Illinois Tool Works, Inc.

6

• Vibration Resistance;HVAC Applications.

*Available with bonded washer.

** With serrations under head.

†Electro-zinc finish.rNowavailable in small box packaging.

N E W

Product FeaturesPoint has precise cutting edges to improve drillperformance with less effort.

Non-walking point provides fast materialengagement.

Point to thread design maximizes pulloutperformance and minimizes backout.

Drills and taps in the broadest range of applications.

Climaseal® finish provides excellent corrosionresistance and lower tapping torque.

ME

DIU

MD

UT

YA

PP

LICAT

ION

SP

RO

DU

CT

RE

PO

RT

NO.02702

The best point e ver f or speed and consistenc y ...

optim um f or medium duty applications.

Product SpecificationsDiameter #12, 1/4Thread Form 12-14

1/4-14Head Style #12: 5/16'' HWH

1/4: 3/8'' HWH1/4 Overhead Door Fasteners:

7/16'' HWH with SerrationsDrill P oint Teks 2

Teks 3 Finish Climaseal®

Head Style

TEKS ®


ApplicationsRoof deck to steel framing.Wall panel to girt.Duct work to steel framing.

Accessories to steel framingClip to steel framing.Retrofit framing.Commercial overhead steel doors, hinges & latches.

Corr osion ResistanceKesternic h Results (DIN 50018, 2.0L) Salt Spra y Results (ASTM B117)• 30 Cycles - 10% or less red rust • 720 hours - 10% or less red rust

7

Hex Washer Head with SerrationsHex Washer Head

Appr ovals and ListingsSteel Deck Institute.

Dia.

1/4

Pt.233

26156142141

24243211231

22283289293

20375341346

18605551613

16848757880

14118110631145

12185616311858

3/16352029984550

Selector GuideTEKS ®


Performance Data

Part Head Drill Drill & Tap Max. Material Bo xNumber Description Style Point Capacity Attac hment Qty Applications

1134000r 12-14 x 3/4'' HWH #3 .036-.210 .270 5,0001136000r 12-14 x 1'' HWH #3 .036-.210 .520 4,0001120000 12-14 x 1-1/4'' HWH #2 .036-.210 .550 4,0001123000 12-14 x 1-1/2'' HWH #2 .036-.210 .800 2,5001140000 12-14 x 2'' HWH #3 .036-.210 1.450 2,0001553000 12-14 X 2-1/2'' HWH #3 .036-.210 1.950 1,0001143000 12-14 x 3'' HWH #3 .036-.210 2.450 1,0001146000 12-14 x 4'' HWH #3 .036-.210 3.450 5001147000 1/4-14 x 3/4'' HWH #3 .036-.210 .210 3,0001149000r 1/4-14 x 1'' HWH #3 .036-.210 .400 2,5001150000 1/4-14 x 1-1/4'' HWH #3 .036-.210 .650 2,0001152000 1/4-14 x 1-1/2'' HWH #3 .036-.210 .900 2,0001155000 1/4-14 x 2'' HWH #3 .036-.210 1.400 1,5001554000 1/4-14 x 2-1/2'' HWH #3 .036-.210 1.900 1,0001157000 1/4-14 x 3'' HWH #3 .036-.210 2.400 1,0001304000 1/4-14 x 4'' HWH #3 .036-.210 3.400 500

All available with bonded washer.

1586000 1/4-14 x 3/4'' *HWH #3 .036-.210 .250 3,0001587000 1/4-14 x 1'' *HWH #3 .036-.210 .500 2,500r Now available in small box packaging. *With serrations under head.

Fastener(dia-tpi)12-141/4-14

Tensile(lbs. min.)

27784060

Shear(avg. lbs. ult.)

20002600


92150

FASTENER VALUES

12

.105''

14

.075''

16

.060''

18

.048''

20

.036''

22

.030''

24

.024''

26

.018''

Gauge No.

Decimal Equivalent

SHEET STEEL GAUGES

Installation GuidelinesA standard screwgun with a depth sensitive nosepieceshould be used to install Teks. For optimal fastener performance, the screwgun should be a minimum of 4amps and have a RPM range of 0-2000.Adjust the screwgun nosepiece to properly seat the fastener.New magnetic sockets must be correctly set before use.Remove chip build-up as needed.

The fastener is fully seated when the head is flush with thework surface.Overdriving may result in torsional failure of the fastener orstripout of the substrate.The fastener must penetrate beyond the metal structure aminimum of 3 pitches of thread.

Teks®, Climaseal® and Building Ideas That Work® aretrademarks of ITW Buildex and Illinois Tool Works Inc.

The values listed are ultimate averages achieved under laboratory conditions and apply to Buildex manufactured fasteners only. Appropriate safety factors should beapplied to these values for design purposes.


• Roof deck to steel framing.

• Wall panel to girt.

• Duct work to steel framing.

• Accessories to steel framing.

• Clip to steel framing.

• Retrofit framing.


• Commercial overhead steeldoors, hinges & latches.

Fastener Steel Gaug ePULLOUT VALUES (average lbs. ultimate)

12

Dia.

1/4

Pt.233

26365

--

24600

--

22623

--

20898769930

18137013581442

16175816202100

14213819702584

12220219862650

Fastener Steel Gaug e (lapped)SHEAR VALUES (average lbs. ultimate)

12

N E W

8

HE

AV

YD

UT

YA

PP

LICAT

ION

SP

RO

DU

CT

RE

PO

RT

NO.02703

Product Features

Unique double fluted point has precise cuttingedges to improve drill performance in 1/4''thru 1/2'' steel.

Engineered for fast drilling and smooth tappingwith less effort.


Attachments up to 7.2'' of material including 1/2'' steel.

1/4 Diameter has notched threads to reduce tapping torque.

First in perf ormance!!

Over 30 y ears of consistent drilling.

The original self-driller s for hea vy duty applications.

TEKS ®


Product Specifications

Diameter #12, 1/4Thread Form 12-24, 1/4-28Head Style #12: 5/16'' HWH

1/4: 5/16'' HWH1/4: 3/8'' HWH

Drill P oint Teks 4 Teks 4.5 Teks 5

Finish Climaseal

Head StyleHex Washer Head

Appr ovals and ListingsFactory Mutual (J.I. 2 X 942 AM), ICBO 3056,Steel Deck Institute.

ApplicationsMetal deck to structural steel or bar joist.

Clips to structural steel or bar joist.

Liner panels to structural steel or bar joist.

Accessories to structural steel or bar joist.

Longer length fasteners can be used in retrofit clip and sheet applications.


9

Note: Teks fasteners are not categorized as structural bolts. Proper design criteria and strengthsmust be used for satisfactory application.The values listed are ultimate averages achieved under laboratory conditions and apply to Buildexmanufactured fasteners only. Appropriate safety factors should be applied to these values for designpurposes.

TEKS ®


SelectorGuide

Part Head Drill Drill & Tap Max. Material Bo xNumber Description Style P oint Capacity Attac hment Qty Applications

1088000r 12-24 x 7/8'' HWH #4 .125-.250 .325 5,0001414000 12-24 x 1-1/4'' HWH #4.5 .125-.375 .575 4,0001006000r 12-24 x 1-1/4'' HWH #5 .125-.500 .375 4,0001070000 12-24 x 1-1/2'' HWH #5 .125-.500 .625 2,5001072000 12-24 x 2'' HWH #5 .125-.500 1.125 2,0001074000 1/4-28 x 3'' *HWH #5 .125-.500 2.150 1,000 1075000 1/4-28 x 4'' *HWH #5 .125-.500 3.150 5001641000 1/4-28 x 5'' HWH #5 .125-.500 4.150 2501431000 1/4-28 x 6" HWH #5 .125-.500 5.150 2501590000 1/4-28 x 8" HWH #5 .125-.500 7.150 150

r Now available in small box packaging.

Performance Data

Dia. Pt.

4

4.5

5

5

16

-

-

-

-

14

-

-

-

-

12

1532

1508

1527

1507

3/16

3485

3865

3701

3300

1/4

4013

4101

3999

5059


Dia. Pt.

4

4.5

5

5

16

-

-

-

1597

14

-

-

-

2005

12

2048

2641

2650

2350

1/8

2030

2887

2700

2792

1/4

-

2897

2762

3310


Fastener(dia-tpi)

12-24 T/412-24 T/4.512-24 T/51/4-28 T/5

Tensile(lbs. min.)

3020316531885577


2100220022003310


100150150234

FASTENER VALUES

12

1/412

1/4

12

.105''

14

.075''

16

.060''

18

.048''

20

.036''

22

.030''

24

.024''

26

.018''

Gauge No.

Decimal Equivalent

SHEET STEEL GAUGES

Installation GuidelinesA standard screwgun with a depth sensitive nosepieceshould be used to install Teks. For optimal fastener performance, the screwgun should be a minimum of 4amps and have a RPM range of 0-2000. (Maximum 1800 RPM is recommended for Teks 5 fasteners)Adjust the screwgun nosepiece to properly seat the fastener.

New magnetic sockets must be correctly set before use.Remove chip build-up as needed.The fastener is fully seated when the head is flush with thework surface.Overdriving may result in torsional failure of the fastener orstripout of the substrate.The fastener must penetrate beyond the metal structure aminimum of 3 pitches of thread.

Teks®, Climaseal® and Building Ideas That Work® are trademarks of ITW Buildex and Illinois Tool Works Inc.


10


• Metal deck, clips, linerpanels or accessories to structural steel or bar joist.

• Longer fasteners can beused in retrofit clip andsheet applications.

* 5/16” Across Flats HWH. All available with bonded washer.

N E W

Product Features#12 diameter utilizes the ITW exclusive PhillipsSquare-Driv ® with patented interlocking components system.- Excellent installation stability.- Extended bit driver life.- Keeps the driver securely mated to the fastener

during installation.- Hands-free installation.

Low profile pancake head style ensures properinstallation of metal roof panels.

#10 Diameter uses the coated Phillips drive system providing improved driver bit-to-fastenerstability and friction fit.

#10 has above industry average tensile strength.

Both fasteners are finished with a corrosionresistant coating. Teks 3 fasteners are availablewith Gray Spex™ coating; Type A fastenerswith Climacoat ®.

Sharp convex drill point has precise cutting edgesto improve drill performance with less effort.

LO

WP

RO

FILE

AR

CH

ITE

CT

UR

AL

ME

TAL

RO

OF

CLIP

FA

ST

EN

ER

PR

OD

UC

TR

EP

OR

TN

O.02704

Incorporates the ITW e xclusive Phillips Square-Dri v ®

anti-cam-out system.


Diameter #10, #12Thread Form 10-16 (Teks 3), 10-12 (Type A)

12-14 ( Teks 3), 12-11 (Type A)Head Style #10 : #2 Phillips Pancake

#12: #2 Phillips Square-Driv® PancakeDrill P oint Teks® 3, Type A Finish Climacoat® (Type A)

Gray Spex™ (Teks 3)

TEKS ®

Low Profile Ar chitecturalMetal Roof Clip F astener s.

BX

ApplicationsLow profile architectural metal roof clips to steel purlin.

Low profile architectural metal roof clips to wood supports.

Corr osion ResistanceKesternic h Results (DIN 50018, 2.0L) Salt Spra y Results (ASTM B117)

Climacoat® • 20 Cycles - 10% or less red rust • 500 hours - 10% or less red rustGray Spex™ • 15 Cycles - 5% or less red rust • 300 hours - 10% or less red rust

#2 Phillips Square-Driv®

#2 Phillips

Teks ® 3

Type A

11

BX

Selector GuideTEKS ®


Performance Data


1560553 10-16 x 1'' #2 Phillips Pancake #3 .036-.175 .550 4,000

1575553 12-14 x 1'' #2 PSD Pancake #3 .036-.210 .550 4,000

1588910 #2 PSD Bit 1

1596553 10-12 x 1” #2 Phillips Pancake Type A .012-.048 .250 4,000

1640553 10-12 x 1-1/2'' #2 Phillips Pancake Type A .012-.048 .750 2,500

1597553 12-11 x 1” #2 PSD Pancake Type A .012-.048 .250 4,000

Dia.#10#12#10#12

Pt.33

TypeA

TypeA

26109139192193

24180194280300

22218250360387

20278369460464

18427450568621

16583598

--

14873915

--

1214061500

--


20 gaug e727923

18 gaug e11641279

16 gaug e13661657

14 gaug e14601933

Dia.#10#12

Pt.33


Fastener(dia-tpi)10-1612-1410-1212-11

Point#3#3

Type AType A

Tensile(lbs. min.)

1983265225813634


1400200014261994


789281

132

FASTENER VALUES

12

.105''

14

.075''

16

.060''

18

.048''

20

.036''

22

.030''

24

.024''

26

.018''

Gauge No.

Decimal Equivalent

SHEET STEEL GAUGES

Installation GuidelinesA standard screwgun with a depth-sensitive nosepieceshould be used to install Teks. For optimal fastener performance, the screwgun should be a minimum of 4amps and have a RPM range of 0-2000.

Adjust the screwgun nosepiece to properly seat the fastener.

The fastener is fully seated when the head is flush with thework surface.

Phillips Square-Driv® is a registered trademark of the Phillips Screw Company. Teks®, Climacoat®,Spex™ and Building Ideas That Work® are trademarks of ITW Buildex and Illinois Tool Works Inc.

The values listed are ultimate averages achieved under laboratory conditionsand apply to Buildex manufactured fasteners only. Appropriate safety factorsshould be applied to these values for design purposes.


• Low profile architectural metalroof clip to steel purlin.

• For #12 Diameter Fastener

• Low profile architectural metalroof clip to wood supports.

1/2” Plywood

364377

5/8” Plywood

382395

3/4” Plywood

400427

Yello w Pine

579675

3/4'' OSB

288326

Dia.#10#12

Pt.Type A

Type A

Fastener Wood Type & Thic knessPULLOUT VALUES (average lbs. ultimate)


12

Overdriving may result in torsional failure of the fastener orstripout of the substrate.

The fastener must penetrate a minimum of 3 pitches of thread beyond the metal structure.

TEKS ®

Wood-to-Metal F astener s

WO

OD-T

O-ME

TAL

AP

PLIC

ATIO

NS

PR

OD

UC

TR

EP

OR

TN

O.02705

Product FeaturesPoint has precise cutting edges to improve drill performance with less effort.

Special winged fasteners ream a hole in woodpreventing thread engagement during drilling.

Wafer head design has a large bearing surface ideal for plywood.

Flat head design countersinks and seats flush in wood.

Gray Spex™ finish provides excellent corrosionresistance and lower tapping torque.

No pre-drilling, fast, efficient attac hment of w ood to steel.

Product SpecificationsDiameter #10, #12 and 1/4Thread Form 10-16

10-2412-241/4-20

Head Style #10: #2 Phillips Flat; #2 Phillips Wafer; #2 Phillips Square-Driv® Flat#12: #3 Phillips Flat1/4: #3 Phillips Flat

Drill P oint Teks 3 Teks 4

Finish Gray Spex™

Head StylesWafer Head Flat Head

Phillips Square Driv®

ApplicationsPlywood roof and floor sheet to steel frames.

2 x 4 headers to steel frames.Plywood fascia to steel frames.Wood mansard to steel frames.


13

N E W

Dia.#10

#12

1/4

Pt.3

4

4

20728

-

-

181266

-

-

161540

-

-

141522

-

-

12-

2048

2650

1/8-

2030

2820

TEKS ®


Selector Guide

Performance Data



Fastener(dia-tpi)10-1610-2412-241/4-20

Tensile(lbs. min.)

1936270231653860


1400150022002700


6165

150168

FASTENER VALUES

12

.105''

14

.075''

16

.060''

18

.048''

20

.036''

22

.030''

24

.024''

26

.018''

Gauge No.

Decimal Equivalent

SHEET STEEL GAUGES

A standard screwgun with a depth sensitive nosepieceshould be used to install Teks. For optimal fastener performance, the screwgun should be a minimum of 4amps and have a RPM range of 0-2000.Adjust the screwgun nosepiece to properly seat the fastener.Worn or damaged bit tip should be replaced.The fastener is fully seated when the head is flush withthe work surface.

Overdriving may result in torsional failure of the fasteneror stripout of the substrate.The fastener must penetrate beyond the metal structure aminimum of 3 pitches of thread.All #10 diameter “Winged” parts must be driven into aminimum of 16 GA steel thickness.All 1/4 and #12 diameter “Winged” parts must be driveninto a minimum of 1/8" steel in order to break the wingsconsistently.

Teks®, Climaseal®, Spex™ and Building Ideas That Work® aretrademarks of ITW Buildex and Illinois Tool Works Inc.

Phillips Square Driv® is a registered trademarkof the Phillips Screw Company.

The values listed are ultimate averages achieved under laboratory conditions and apply toBuildex manufactured fasteners only. Appropriate safety factors should be applied to thesevalues for design purposes.


14

Installation Guidelines

Dia.#10-16

#10-24

#12

1/4

Pt.3

3

4

4

26-

-

-

-

24208

-

-

-

22266

-

-

-

20299

334

-

-

18499

495

-

-

16708

702

683

788

14967

900

923

1116

121474

1570

1508

1803

3/16-

3865

4297

1/4-

4101

-


WoodPart Head Drill Drill & Tap Attac hment BV Applications

Number Description Style Point Capacity Range1077000 10-24 x 3/4" Wafer #3 .036-.175 1/4''-3/8'' 8,000 • Plywood, mansard, fascia,1079000 10-24 x 1" Wafer #3 .036-.175 1/4''-1/2'' 5,000 roofing, flooring to steel1082000r 10-24 x 1-7/16"* PFH #3 .060-.175 1/4''-3/4'' 3,000 framing.

1791000 10-16 x 1-13/16'' PSD Flat** #3 .030-.175 1/4''-3/4'' 2,500

1588910 #2 PSD Bit 1

1092000r 12-24 x 2-1/4" PFH* #4 .125-.250 3/4''-1-3/8'' 2,0001094000r 12-24 x 2-3/4" PFH* #4 .125-.250 3/4''-1-5/8'' 1,500

1096000 1/4-20 x 3" PFH* #4 .125-.250 3/4''-2'' 1,000

*with wings **with ribs under headr Now available in small box packaging.N E W

N E W

N E W

• Plywood, 2 x 4’s headers

to steel framing.

• 2 x 4’s to steel framing.N E W

WOOD-TO-METAL

BoxQty

ME

TAL

RO

OF

AN

DW

ALL

AP

PLIC

ATIO

NS

PR

OD

UC

TR

EP

OR

TN

O.02706

For weather -tight sealing of r oof and wall applications.

Product SpecificationsDiameter #10, #12 & 1/4Thread Form 10-16

12-1412-241/4-141/4-28

Head Style #10: 5/16'' HWH#12: 5/16'' HWH1/4 (stitch): 5/16'' HWH1/4: 3/8'' HWH

Washer Style Galvanized (G-90)

Drill P oint Teks 1 Teks 2 Teks 3 Teks 4 Teks 4.5 Teks 5

Finish Climaseal®

Head Paint AvailableHead Style

Hex Washer Head with Bonded Washer

TEKS ®

Self-Drilling F astener sWith Bonded Washer

Product Features

Vulcanized bonding of washer eliminates separationof EPDM from the metal backing.

Dual sealing bonded washer prevents leaks.


Point has precise cutting edges to improve drill performance with less effort.

Point to thread design maximizes pulloutperformance and minimizes backout.

Applications

Roof panels to purlin or bar joist. Wall panels to girt. Mansard panel to structural.


15

Installation GuidelinesA standard screwgun with a depth sensitive nosepiece should be used to install Teks. For optimal fastener performance, the screwgun should be a minimum of 4 amps and have a RPM range of 0-2000.Adjust the screwgun nosepiece to properly seat the fastener.New magnetic sockets must be correctly set before use. Remove chip build-up as needed.

Overdriving may result in torsional failure of the fastener or stripoutof the substrate.The fastener must penetrate beyond the metal structure a minimumof 3 pitches of thread.

Part Head Drill Drill & Tap Max. Material Bo xNumber Style Point Capacity Attac hments Qty1005000 10-16 x 3/4” HWH #3 .036 - .175 .205 3,0001308000 10-16 x 1-1/2” HWH #3 .036 - .175 .955 2,500 • Brick tie to steel framing.1011000 12-14 x 1” HWH #3 .036 - .210 .400 3,0001014000 12-14 x 1-1/4” HWH #2 .036 - .210 .430 2,500 • Mansard panel to steel framing.1404000 12-14 x 1-1/2” HWH #2 .036 - .210 .680 2,000 1009000 12-14 x 3/4” HWH #3 .036 - .210 .150 3,000 • Roof panel to purlin.1016000 12-14 x 2” HWH #3 .036 - .210 1.330 1,5001333000 12-14 x 3” HWH #3 .036 - .210 2.330 1,000 • Wall panel to girt.1332000 12-14 x 4” HWH #3 .036 - .210 3.330 5001416000 1/4-14 x 7/8” HWH #1 .018 - .095 .260 3,000 • Stitch roof and wall panels.1160000 1/4-14 x 1” HWH #3 .036 - .210 .280 2,5001019000 1/4-14 x 1-1/4” HWH #3 .036 - .210 .530 2,000 • Retrofit panels to structural.1020000 1/4-14 x 1-1/2” HWH #3 .036 - .210 .780 1,5001021000 1/4-14 x 2” HWH #3 .036 - .210 1.280 1,0001022000 1/4-14 x 3” HWH #3 .036 - .210 2.280 7501429000 1/4-14 x 4'' HWH #3 .036 - .210 3.280 5001010000 12-24 x 7/8” HWH #4 .125 - .250 .205 3,000 • Roof and wall panel to bar joist or1415000 12-24 x 1-1/4” HWH #4.5 .125 - .375 .455 2,500 structural.1000000 12-24 x 1-1/4” HWH #5 .125 - .500 .255 2,500 1001000 12-24 x 1-1/2” HWH #5 .125 - .500 .505 2,0001002000 12-24 x 2” HWH #5 .125 - .500 1.005 1,500 • Longer fasteners may be used in1003000 1/4-28 x 3” HWH #5 .125 - .500 2.030 1,000 retrofit applications.1004000 1/4-28 x 4” HWH #5 .125 - .500 3.030 5001647000 1/4-28 x 5'' *HWH #5 .125 - .500 4.030 2501642000 1/4-28 x 5'' **HWH #5 .125 - .500 4.030 2501432000 1/4-28 x 6” *HWH #5 .125 - .500 5.030 2501619000 1/4-28 x 8” *HWH #5 .125 - .500 7.030 150

TEKS ®

SELF-DRILLING FASTENERS WITH 9/16'' B ONDED WASHER

SelectorGuide

12

.105''

14

.075''

16

.060''

18

.048''

20

.036''

22

.030''

24

.024''

26

.018''

Gauge No.

Decimal Equivalent

SHEET STEEL GAUGES

Fastener(dia-tpi)10-1612-1412-241/4-141/4-28

Tensile(lbs. min.)

19362778302040605577


14002000210026003310


6192

100150234

FASTENER VALUES

Properl y Seated Washer s

Underdriven Correctly OverdrivenDriven

Teks®, Climaseal® and Building Ideas That Work® are trademarks of ITW Buildex and Illinois Tool Works Inc.



16

* 3/4'' bonded washer**1-1/8'' bonded washer

Dia.10

Pt.3234

4.55135

26124156142

---

208141

-

24208243211

---

329231

-

22266283289

---

428293

-

20299375341

---

562346

-

18499605551

---

800613

-

16708848757

---

1151880607

14967

11811063

----

1145918

12147418561631153215081527

-18771507

3/16-

35202998348538653701

-45503300

1/4---

384441043999

--

5059


12

12

1/4

Dia.10

Pt.3234

4.55135

26-

365----

511--

24445600

----

849--

22526623

----

885--

20728898769

---

1244930

-

18126613701358

---

17641442

-

16154017581620

----

21001597

14155221381970

----

25842005

12--

1986204826412650

-26502350

1/8---

203028872700

--

2792

1/4--------

3310


12

1/4

12

Performance Data

ApplicationsDescription

PR

EM

IUM

ME

TAL

RO

OF

AN

DW

ALL

AP

PLIC

ATIO

NS

PR

OD

UC

TR

EP

OR

TN

O.02707

Maxiseal ... The premium sealing system f or Teks ®

self-drilling, self-tapping fastener s.

Product FeaturesControls the EPDM washer for improved in place appearance and increased washer life.

Seals when driven at an angle.

Optimum pullover resistance.

Hex washer head provides excellent driving stability.


Non-walking point provides fast material engagement.

Point to thread design maximizes pullout performance and minimizes backout.



Product SpecificationsDiameter #10, #12, 1/4 and #17Thread Form 10-16

12-14, 12-241/4-1417-14

Head Style #10: 5/16'' HWH#12: 5/16'' HWH1/4: 5/16'' HWH and 3/8'' HWH#17: 5/16'' HWH

Washer Style 9/16'' O.D. Integral System

Drill P oint Teks 1 Teks 2Teks 3 Teks 4Teks 5Type AB

Finish Climaseal®

Head Paint AvailableHead Style Maxiseal® Head

MAXISEALIntegral Washer System

ApplicationsRoof panel to purlin and wall panel to girt.

Stitching roof, wall, fascia, eave panels or gutterstraps.

Roof and wall panel or accessories over blanket insulation to steel framing.

#17 diameter replacement for stripped #12 and1/4 diameter fasteners.


17

®

MAXISEAL INTEGRAL WASHER SYSTEM

SelectorGuide

Fastener(dia-tpi)10-1612-14

12-24 T/412-24 T/5

1/4-1417-14

Tensile(lbs. min.)

193627783020318840605300


140020002100220026003200


6192

100150150180

FASTENER VALUES

Installation GuidelinesA standard screwgun with a depth sensitive nosepiece should be usedto install Teks. For optimal fastener performance, the screwgun shouldbe a minimum of 4 amps and have a RPM range of 0-2000.Adjust the screwgun nosepiece to properly seat the fastener.New magnetic sockets must be correctly set before use. Remove chipbuild up as needed.

Overdriving may result in torsional failure of the fastener or stripout ofthe substrate.The fastener must penetrate beyond the metal structure a minimum of 3 pitches of thread.

12

.105''

14

.075''

16

.060''

18

.048''

20

.036''

22

.030''

24

.024''

26

.018''

Gauge No.

Decimal Equivalent

SHEET STEEL GAUGES



Teks®, Maxiseal®, Climaseal® and Building Ideas That Work® are trademarks of ITW Buildex and Illinois Tool Works Inc.


Product Report No. 02707®


18

Dia.10

17

Pt.3234513

ABAB

26124156142

--

208141235225

24208243211

--

329231365261

22266283289

--

428293496350

20299375341

--

562346597442

18499605551

--

800613702553

16708848757697

-1151880926752

14967

11811063986

--

114511801122

1214741856163115321527185818771716

-

3/16-

3520299834853701455045503523

-

1/4---

40133999

----


12

1/4

Dia.10

17

Pt.3234513

ABAB

26-

365---

511-

422459

24445600

---

849-

482745

22526623

---

885-

669989

20728898769

--

1244930889958

18126613701358

--

1765144211571415

16154017581620

---

2100--

14155221381970

---

2584--

12--

198620482650

- -2650

--


12

1/4

Performance Data


1376000 10-16 x 3/4” HWH #3 .036-.175 .325 3,0001023000 12-14 x 3/4” HWH #3 .036-.210 .260 3,0001026000r 12-14 x 1” HWH #3 .036-.210 .490 2,5001029000r 12-14 x 1-1/4” HWH #2 .036-.210 .560 2,5001428000 12-14 x 1-1/2” HWH #2 .036-.210 .790 2,0001730000 12-24 x 7/8'' HWH #4 .018-.250 .295 3,0001517000 12-24 x 1-1/2'' HWH #5 .125-.500 .500 2,5001389000 1/4-14 x 7/8” HWH #1 .018-.095 .320 3,000r

1042000 1/4-14 x 3/4” *HWH #3 .036-.210 .200 3,000 • Sheet or accessories with up to 6” blanket1044000 1/4-14 x 1” *HWH #3 .036-.210 .310 2,500 insulation to steel framing.1048000 1/4-14 x 1-1/2” *HWH #3 .036-.210 .810 2,0001737000 1/4-14 x 1-3/4'' *HWH #3 .036-.210 1.060 1,5001712000 1/4-14 x 3” HWH #3 .036-.210 2.310 1,0001063000 17-14 x 1” HWH AB - .685 2,500 • Replacement screw for 12 and 1/4'' diameter

fasteners.

r Now available in small box packaging.

• Stitching roof, wall, fascia, eave panels or gutterstraps.

• Roof and wall panel to bar joist or structural.

*3/8'' Across Flats

N E W

N E W

N E W

• Roof and wall panel to steel framing.

• Panel over insulation to steel framing.

SCOTSLong Lif e Teks ® Fastener s

LO

NG

LIF

EM

ETA

LR

OO

FA

ND

WA

LLA

PP

LICAT

ION

SP

RO

DU

CT

RE

PO

RT

NO.02708

The Original Builde x Scots 300 Stainless Steel Encapsulated

Head will ne ver rust .... EVER!!!!

Product Features

For improved appearance and extra life an integraldesign controls the EPDM washer.

Combines 300 series stainless steel exterior with the strength of carbon steel.

300 series stainless most preferred for galvalume longlife panels.

Maximum sealing and corrosion protection.



Point to thread design maximizes pullout performanceand minimizes backout.


Product SpecificationsDiameter #12, 1/4 and #17Thread Form 12-14

12-241/4-141/4-2817-14

Head Style 5/16'' HWH (300 Series Stainless)Washer Style 9/16'' O.D. IntegralDrill P oint Teks 1

Teks 2Teks 5 Type AB

Finish Silver Climaseal®

Head paint available

Head StyleScots Head

Corr osion ResistanceSCOTS will ne ver rust .... EVER!!!!

ApplicationsPanel over blanket insulation to steel frame.

Roof curb to structural steel.

Standing seam roof system endlaps.

Stitch roof and wall sidelaps.

#17 diameter replacement screw for #12 and 1/4diameter fasteners.

19

®


1165253 12-14 x 1'' HWH #3 .036-.210 .310 2,5001167253 12-14 x 1-1/4'' HWH #2 .036-.210 .560 2,500 • Panel over blanket insulation to steel frame.1168253 12-14 x 1-1/2'' HWH #2 .036-.210 .790 2,0001163000 12-24 x 2'' HWH #5 .125-.500 1.000 1,500 • Roof curb to structural steel1788000 1/4-28 x 4'' HWH #5 .125-.500 3.000 5001387253 1/4-14 x 7/8'' HWH #1 .018-.095 .320 2,500 • Stitch roof and wall sidelaps. SSR endlaps.1175153 1/4-14 x 1-1/8'' HWH #1 .018-.095 .395 2,500 • Standing seam roof system endlaps.1616000 1/4-14 x 1-1/4'' HWH #3 .036-.210 .630 2,0001178253 1/4-14 x 3/4'' HWH AB - .435 2,500 1701000 1/4-14 x 1-1/2'' HWH AB - .870 2,000 • Replacement screw for #12 and 1/4 diameter1180225 17-14 x 1'' HWH AB - .686 2,500 fasteners.

Selector GuideSCOTS LONG LIFE FASTENERS

Performance Data

Installation GuidelinesA standard screwgun with a depth sensitive nosepieceshould be used to install Teks. For optimal fastener performance, the screwgun should be a minimum of 4ampsand have a RPM range of 0-2000.Adjust the screwgun nosepiece to properly seat the fastener.New magnetic sockets must be correctly set before use.Remove chip build-up as needed.

Overdriving may result in torsional failure of the fastener orstripout of the substrate.The fastener must penetrate beyond the metal structure aminimum of 3 pitches of thread.



Scots®, Teks®, Climaseal®, and Building Ideas That Work® are trademarks of ITW Buildex and Illinois Tool Works Inc.

The values listed are ultimate averages achieved under laboratory conditions and apply toBuildex manufactured fasteners only. Appropriate safety factors should be applied tothese values for design purposes.



20

Dia.12121/4

17

Pt.2551

ABAB

26156

--

208235225

24243

--

329365261

22283

--

428496350

20375

--

562597442

18605

--

800702553

16848

--

1151926752

141181

---

11801122

12185615271507

-16901716

3/16352037013300

-34463523

1/4-

39995059

-42124250


1/4

Fastener(dia-tpi)12-1412-241/4-141/4-2817-14

Tensile(lbs. min.)

27783188406055775300


20002200260033103200


92130150234180

FASTENER VALUES

12

.105''

14

.075''

16

.060''

18

.048''

20

.036''

22

.030''

24

.024''

26

.018''

Gauge No.

Decimal Equivalent

SHEET STEEL GAUGES

®

N E W

Dia.12121/4

17

Pt.2551

ABAB

26365

--

511422459

24600

--

849482745

22623

--

885669989

20898

--

1244889958

181370

--

176411571415

161758

-1597

---

142138

-2005

---

1/8220227002350

---

3/16-

27202792

---

1/4-

27623310

---


1/4

The original self-drilling fastener s designed specificall y for

rigid insulation.

TEKS ®

EXTERIOR RIGID INSULATION FASTENERS

EX

TE

RIO

RR

IGID

INS

ULAT

ION

AP

PLIC

ATIO

NS

PR

OD

UC

TR

EP

OR

TN

O.02709

Product SpecificationsDiameter #12Thread Form 12-14 with rider sectionHead Style 5/16'' HWH Maxiseal

5/16'' HWH Scots 300 SeriesStainless

Washer Style 9/16'' O.D. Integral SystemDrill P oint Teks 3 Finish Climaseal

Head paint available.

Head StylesMaxiseal Head

Scots Head

ApplicationsRoof and wall panel over rigid insulation to steel framing. Roof panel over spacer block and insulation to eave purlin.

Product FeaturesUnique rider section stops panel jacking, point burnoutand breakage.

High thread under the head prevents panel stripout.

Improved in place aesthetics.

Available in Scots® and Maxiseal® headstyles.

Maximum pullover performance.

Excellent driving stability.

Seals when driven at an angle.

Fastens the broadest range of insulation thickness.

Point has precise cutting edges to improve drillperformance with less effort.


Point to thread design maximizes pullout performanceand minimizes backout.


Corr osion ResistanceMaxiseal:

Kesternic h Results (DIN 50018, 2.0L)• 30 Cycles - 10% or less red rust

Maxiseal:Salt Spra y Results (ASTM B117)

• 720 hours - 10% or less red rust

Scots:

• Scots will ne ver rust ... EVER!!!!

21

Part Head Drill Drill & Tap Insulation Bo xNumber Description Style Point Capacity Rang e Qty Application

Maxiseal ®

1034000 12-14 x 1-7/8" HWH #3 .036-.210 3/4" to 1" 1,5001036000 12-14 x 2-3/8" HWH #3 .036-.210 1-1/8" to 1-1/2" 1,000 • Roof and wall panel over rigid1038000 12-14 x 3-1/4" HWH #3 .036-.210 1-5/8" to 2-3/8" 750 insulation to steel framing.1040000 12-14 x 4" HWH #3 .036-.210 2-1/8" to 3" 500Scots ®

1169200 12-14 x 1-7/8" HWH #3 .036-.210 3/4" to 1" 1,500 • Roof panel over spacer block1170200 12-14 x 2-3/8" HWH #3 .036-.210 1-1/8" to 1-1/2" 1,000 and insulation to eave purlin.1171200 12-14 x 3-1/4" HWH #3 .036-.210 1-5/8" to 2-3/8" 7501172200 12-14 x 4" HWH #3 .036-.210 2-1/8" to 3" 500

TEKS ®

EXTERIOR RIGID INSULATION FASTENERS

Selector Guide

Performance Data

Dia.

12

Pt.

3

26

142

24

211

22

289

20

341

18

551

16

757

14

1063

12

1631

3/16

2998


Fastener(dia-tpi)

12-14

Tensile(lbs. min.)

2778


2000

Torque (min. in. lbs. )

90

FASTENER VALUES

Dia.

12

Pt.

3

26

-

24

-

22

-

20

769

18

1358

16

1620

14

1970

12

1986


12

.105''

14

.075''

16

.060''

18

.048''

20

.036''

22

.030''

24

.024''

26

.018''

Gauge No.

Decimal Equivalent

SHEET STEEL GAUGES

Installation GuidelinesA standard screwgun with a depth sensitive nosepieceshould be used to install Teks. For optimal fastener performance, the screwgun should be a minimum of 4ampsand have a RPM range of 0-2000.


New magnetic sockets must be correctly set before use.Remove chip build-up as needed.

Overdriving may result in torsional failure of the fastener orstripout of the substrate.

The fastener must penetrate beyond the metal structure aminimum of 3 pitches of thread.



Teks®, Scots®, Maxiseal®, Climaseal® and Building Ideas That Work® are trademarks of ITW Buildex and Illinois Tool Works Inc.

The values listed are ultimate averages achieved under laboratory conditions and apply toBuildex manufactured fasteners only. Appropriate safety factors should be applied tothese values for design purposes.



22

ME

TAL-TO-W

OO

DA

PP

LICAT

ION

SP

RO

DU

CT

RE

PO

RT

NO.02711

Product FeaturesNon-walking sharp gimlet point for fast materialengagement.

Double lead thread for fast panel pick-up.

Dual sealing bonded washer prevents leaks.

Vulcanized bonding of washer eliminatesseparation of EPDM from the metal backing.

High hat HWH for driving stability.


The pref erred fastener b y the leading post frame b uilder s and

manufacturer s.

TRUGRIP GTMetal-to-W ood F astener s


Diameter #9 and #12Thread Form 9-15 double lead

12-14Head Style 1/4” HWHWasher Style Galvanized (G-90)Drill P oint GimletFinish Climaseal®

Head Paint Available

Head StylesHex Washer Head

Hex Washer Head with Bonded Washer

ApplicationsRoof and wall panel to wood structure.

Panel over insulation to wood structure.

Stitch roof and wall panel.

Corr osion ResistanceKesternic h Results (DIN 50018, 2.0L) Salt Spra y Results (ASTM B117)• 30 Cycles - 10% or less red rust • 720 Hours - 10% or less red rust

23

TM

TRUGRIP GT METAL-TO-WOOD FASTENERS

Performance Data

9

12

26171

199

24252

271

22329

360

20401

426

18634

656

FastenerDia.

Steel Gaug ePULLOUT VALUES IN STEEL (average lbs. ultimate)

9

12

1/2''198

210

3/4''328

335

1''571

-

1-1/4''728

-

1-1/2''872

-

FastenerDia.

Embedment in 2'' x 4''PULLOUT VALUES IN WOOD (average lbs. ultimate) Dia.

99

1212

26465515527587

24623674699744

22815875863915

2010491100912993

181549162711851246

Fastener Steel Gaug ePULLOVER VALUES (average lbs. ultimate)

Unwashered

Washered

Unwashered

Washered

Fastener(dia-tpi)

9-1512-14

Tensile(lbs. min.)

18002778


12002000


5092

FASTENER VALUES

GaugeNo.

18

20

22

24

26

28

30

DecimalEquiv alent

.048''

.036''

.030''

.024''

.018''

.015''

.012''

SHEET STEEL GAUGES

Installation GuidelinesA standard screwgun with a depth sensitive nosepiece should be used to install TruGrip™. For optimal fastener performance, the screwgun should be a minimum of 4 amps and have a RPM range of 0-2000.Adjust the screwgun nosepiece to properly seat the fastener.New magnetic sockets must be correctly set before use.Remove chip build-up as needed.

Overdriving may result in torsional failure of the fastener or stripout of the substrate.The fastener must penetrate beyond the metal structure aminimum of 3 pitches of thread.



TruGripTM GT, Climaseal® and Building Ideas That Work® are trademarks of ITW Buildex and Illinois Tool Works Inc.


Selector Guide

1271000 9-15 x 1'' HWH Gimlet .012-.048 0-.250 7,000 • Wall panel to wood1272000 9-15 x 1-1/2'' HWH Gimlet .012-.048 0-.750 4,000 structure1273000 9-15 x 2'' HWH Gimlet .012-.048 .500-1.250 8,000 • Panel over insulation to1275000 9-15 x 2-1/2'' HWH Gimlet .012-.048 1.000-1.750 1,500 wood.1276000 9-15 x 3'' HWH Gimlet .012-.048 1.500-2.250 1,500 1277000 12-14 x 3/4'' HWH Gimlet .012-.048 --- 4,000 • Stitching of wall panel.

With 1/2'' Bonded Washer1262000r 9-15 x 1'' HWH Gimlet .012-.048 0-.250 4,000 • Roof and wall panel to 1264000r 9-15 x 1-1/2'' HWH Gimlet .012-.048 0-.750 2,500 wood.1267000 9-15 x 2'' HWH Gimlet .012-.048 .500-1.250 2,000 • Panel over insulation to1268000 9-15 x 2-1/2'' HWH Gimlet .012-.048 1.000-1.750 1,500 wood.1269000 9-15 x 3'' HWH Gimlet .012-.048 1.500-2.250 1,0001270000 12-14 x 3/4'' *HWH Gimlet .012-.048 --- 4,000 • Stitching of roof and wall

*With 9/16'' O.D. Bonded Washer. panel.

Applications


24

TM


PartNumber Description Head

StyleDrillPoint

Drill &Tap

Capacity

MaterialAttac hment

Range

N E W

BoxQty

ME

TAL-T

O-WO

OD

AP

PLIC

ATIO

NS

SCOTS TRUGRIPLong Lif e Metal-to-W oodFastener s

Product Features

For improved appearance and extra life an integraldesign controls the EPDM washer.

Combines 300 series stainless steel exterior withthe strength of carbon steel.

300 series stainless most preferred forgalvalume long life panels.

Maximum sealing and corrosion protection.

Non-walking sharp gimlet point for fast materialengagement.

Double lead thread for fast panel pick-up.


Combines the corr osion resistance of 300 series stainless steel

with the pr oven efficienc y of TruGrip ™ GT.

Diameter #9 and #12Thread Form 9-15 and 12-14 Double Lead Scots HeadHead Style 1/4'' Across Flats HWH

(300 Series Stainless)Washer Style 7/16'' O.D. Integral Head with EPDM WasherDrill P oint GimletFinish Climaseal®

Head Paint Available

ApplicationsRoof and wall panel to wood structure.

Panel over insulation to wood structure.

Stitch roof and wall panel.

Corr osion Resistance SCOTS will ne ver rust .... EVER!!!!

®

Head Style

™

25

PR

OD

UC

TR

EP

OR

TN

O.02711

1349 West Bryn Mawr AvenueItasca, Illinois 60143630/595-3500 FAX: 630/595-3549www.itwbuildex.com © 2002 Illinois Tool Works Inc.

Scots®, TruGrip™, Climaseal® and Building Ideas that Work®,are all trademarks of ITW Buildex and Illinois Tool Works Inc.

SCOTS® TRUGRIP™ METAL-TO-WOOD FASTENERS Product Report No. 02712

Performance Data

Selector Guide Part Head Drill Drill & Tap Material Attac hment Bo x CommonNumber Description Style P oint Capacity Rang e Qty Applications

1687053 9-15 x 1'' HWH Gimlet .012-.048 0-.250 2,500

1655053 9-15 x 1-1/2'' HWH Gimlet .012-.048 0-.750 2,500

1653053 9-15 x 2'' HWH Gimlet .012-.048 .500-1.250 1,000

1651053 9-15 x 2-1/2'' HWH Gimlet .012-.048 1.000-1.750 1,000

1691053 12-14 x 3/4'' HWH Gimlet .012-.048 ---- 4,000

9

12

26171

199

24252

271

22329

360

20401

426

18634

656

FastenerDia.

Steel Gaug ePULLOUT VALUES IN STEEL (average lbs. ultimate)

9

12

1/2''198

210

3/4''328

335

1''571

-

1-1/4''728

-

1-1/2''872

-

FastenerDia.

Embedment in 2'' x 4'' (SYP)PULLOUT VALUES IN WOOD (average lbs. ultimate)

Fastener(dia-tpi)

912

Tensile(lbs. min.)

18002778


12002000


5092

FASTENER VALUES

Dia.9

12

26515587

24674744

22875915

201100993

1816271246

Fastener Steel Gaug ePULLOVER VALUES (average lbs. ultimate)

Washered

Washered

GaugeNo.

18

20

22

24

26

28

30

DecimalEquiv alent

.048''

.036''

.030''

.024''

.018''

.015''

.012''

SHEET STEEL GAUGES

Installation GuidelinesA standard screwgun with a depth sensitive nosepiece should be used to install Scots® TruGrip™. For optimal fastener performance, the screwgun should be a minimum of 4 amps and have a RPM range of 0-2000.


New magnetic sockets must be correctly set before use.Remove chip build-up as needed.

Overdriving may result in torsional failure of the fastener or stripout of the substrate.

The fastener must penetrate beyond the metal structure aminimum of 3 pitches of thread.




• Roof and wall panel to wood structure.

• Panel over insulation to wood structure.

• Stitching of roof and wall panel.

26

LONG LIFE

DEKTITE ANDRETROFIT DEKTITEPipe Flashings

STEP 1: Cut Dektiteat appropriate pipediameter marking.

STEP 2: Slide Dektiteflashing down over pipe.

STEP 3: Apply sealanton underside of flexiblealuminum base.

STEP 4: Press Dektitebase into contours ofpanel configuration.

STEP 5: Fasten Dektite tosurface with Buildex SCOTSself-drilling fasteners.Apply additional sealantaround base if desired.

PIP

EF

LAS

HIN

GA

PP

LICA

TIO

NS

PR

OD

UC

TR

EP

OR

TN

O. 02714

The original fle xib le pipe flashing system with a 20 y ear

warranty .

Product SpecificationsPipe Diameter Rang es........ 1/4'' to 24'' - Dektite

3/4'' to 10'' - Retrofit Dektite1/4'' to 18'' - Silicone

Materials ...................... EPDM - Standard and RetrofitSilicone - High Temperature

Product FeaturesMade of long life, flexible, weatherproof gray EPDM rubber or red silicone.

Flexible, corrosion resistant aluminum base conformsto any panel configuration.

EPDM and silicone will not crack or break.

Pipe diameter markings are clearly indicated foraccurate fitting.

Designed for 1/4'' to 24'' diameter pipes.

One piece construction is easy to install.

Pleated cone adjusts to any roof pitch and allows forcomplete flexibility.

EPDM has a continuous service temperature range of-65˚F to +250˚F.

Silicone has a continuous service temperature rangeof -40˚F to +350˚F

Proven resistance to ozone and ultra-violet light.

Dektite Installation Guidelines

ApplicationsPlumbing, Heating, Air Conditioning, Electrical and Exhaust Vents.

Notes: • Dekite can be installed over or between the ribs of standard panels.• DO NOT install over SSR or architectural panel ribs.• Generally no sealant is required where the Dektite collar provides a compression fit around the pipe. However, some metal

pipes and flues include a seam which may require a local application of sealant at the point where the Dektite collar crosses the seam.

27

®

®

PartNumber

400191040039104004910400991040359104011910401691040369104018910402091040259104038910402891040399104000910

Descriptio n

Mini123

#3 Silicone45

#5 Silicone678

#8 Silicone9

#9 SiliconeDiverter

PipeOutside

Diameter1/4"-1-1/8"

1/4"-2"1-3/4"-3-1/4''

1/4"-5"

3"-6"

4"-7"

5"-9"6"-11"

7"-13"

10"-18"

16"-24"

DektiteBase

Diameter3-1/2"4-3/4"6-1/4"

7-3/4"

9-1/4"

10-3/4"

12-1/2"14-1/2"

16-1/2"

25-3/8"

39-1/2" x 35''

DektiteHeight

1-3/4"3"4"

4"

5"

5"

6"6"

6"

8"

9"

BoxQuantity

201010

10

10

5

55

5

2

1Note: When used on roofs where pitch is steeper than 20 degrees, or when used on deep ribbed profile roof panel (1-1./2'' deep corrugation or more), consider using next larger size Dektitethat will accommodate the same pipe diameter. Recommended Sealant: Chemseco Sikafle x® sealant, par t number 4040910. Recommended F astener: 1/4-14 x 1-1/8'' Scots ® Teks ®/1,par t number 1175153.

Dektite Flashing Guide

DEKTITE PIPE FLASHINGS

Selector Guide

Performance Data

Standard Dektite Retrofit Dektite

PartNumber

4029910

4030910

4031910

DektiteSize

Number

801

802

803

PipeOutsideDiameter

3/4''-2-3/4''

2''-7-1/4''

3-1/4''-10''

DektiteBase

Diameter

6-3/10''

10-3/4''

14-1/2''

DektiteHeight

3-1/2''

5-3/5''

5-4/5''

BoxQty

10

5

5

Retrofit Dektite ® Selector Guide

ASTM TestMethod Test Description Specification Results

D412 Tensile Strength (min. psi rating) 1450 psi min. 1537 psi

D412 Ultimate Elongation (%) 350 min. 535

D1171 Resistance to Ozone- 100 Passedmin. rating (no cracks)

D673 Heat Aging - 70 hrs. at 212˚F•Change in Hardness (points) ± 15 max. +8

•Change in Tensile Strength (%) ± 30 max. -4.7•Change in Elongation (%) ± 50 max. -26

ASTM TestMethod Test Description Specification ResultsD2137 Low Temperature Brittleness-

3 mins. at -40˚F Non-brittle Passed

Tear Resistance Die C (min.) 125 poundsD624 per inch of per inch of 130 pounds

width min. width

U.L. 94 Flame Resistance U.L. 94 H.B. Passed

STEP 1: Begin cuttingopposite of the mech-anical locking joiner. Cutthrough the joiner with tinsnips.

STEP 2: Wrap RetrofitDektite® around the pipe.Engage the top section ofthe joiner first, then pro-ceed down until joiner iscompletely engaged.

STEP 3: Crimp joinertightly, starting at the topby squeezing joiner “fingers” with pliers.

STEP 4: Apply sealant tothe underside of theribbed aluminum base.Press Retrofit Dektite®

against contours of thepanel configuration.

STEP 5: Attach RetrofitDektite® to the panel withSCOTS® self-drillingscrews. Screws should bespaced as necessary toavoid gaps between thebase and the panel.

STEP 6: Apply additionalsealant around the top ofthe Dektite® and along themechanical locking joinerseam.

Diverter

Retrofit Dektite Installation Guidelines


1349 West Bryn Mawr AvenueItasca, Illinois 60143630/595-3500 FAX: 630/595-3549www.itwbuildex.com ©2002 Illinois Tool Works, Inc.28

Recommended Sealant: Chemseco Sikafle x® sealant, par t number 4040910.

Scots® and Building Ideas That Work® are trademarks ofITW Buildex and Illinois Tool Works Inc.

Dektite® and Retrofit Dektite® are registered trademarks of Deks Industries. Sikaflex® is a registered trademark of Chemseco Corporation.

DEK-CAPStanding Seam Roof End Cap Flashing

Applications


Material .........................Thermal Elastomer

Width .............................7-1/4''

Length ............................5-3/4''

Height ...........................3-5/16''

Color ...............................Gray

ME

TAL

RO

OF

EN

DC

AP

FLA

SH

ING

AP

PLIC

AT

ION

PR

OD

UC

TR

EP

OR

TN

O. 02715

The onl y univer sal end cap flashing!!

Product FeaturesUniversal design allows use on left and righthanded seams.

Flexible, corrosion resistant aluminum baseconforms to the majority of standing seam roof panels.

Pre-formed panel profile shape is designed toreduce installation time.

Fastening locations are clearly indicated for accurate installation.

Dual underside ridges provide maximum sealingprotection.

Thermal elastomer material provides excellentresistance to ozone, ultra-violet light andextreme temperatures.

Thermal elastomer has a continuous temperature of -40˚F to 250˚F.

Expansion notch provides added installationflexibility.

Interior panel stop ensures correct installationposition.

TM

29

Dek-CapTM, Scots® and Building Ideas That Work® are trademarksof ITW Buildex and Illinois Tool Works Inc.

Sikaflex® is a registered trademark of Chemseco Corporation.


STEP 1:Bend top so that bothsides are parallel tometal roof.

STEP 2:Press Dek-Cap edgesinto contours of panelconfiguration.

STEP 3:Remove and applysealant on undersideof flexible aluminum edging.

STEP 4:Slide Dek-Cap flashingover panel profile.

STEP 5:Follow indicated fast-ening pattern to attachDek-Cap to surface withBuildex Scots self-drillingfasteners.

STEP 6:Apply additional sealant around baseif desired.

Selector Guide

DEK-CAP STANDING SEAM ROOF END CAP FLASHING Product Report No. 02715

Part Number

4146910

Description

Dek-Cap

Applications

Metal Curbs, Skylights,Ridge Applications,

Jobsite Retrofit

Box Quantity

10

Performance Data


D412 Tensile Strength (min. psi rating) 1450 psi min. 1500 PSI

D412 Ultimate Elongation (%) 350 min. 450

D1171 Resistance to Ozone- 100 Passedmin. rating (no cracks)

D573

Heat Aging - 70 hrs. at 212˚F•Change in Hardness (points) ± 15 max. +3•Change in Tensile Strength (%) ± 30 max. +2•Change in Elongation (%) ± 50 max. -3


D2137 Low Temperature Brittleness-3 mins. at -40˚F

Non-brittle Passed

D624 Tear Resistance Die C (min.)125 pounds

Passedper inch ofwidth min.


30


™


Material ......................... Hypalon® coated polyester

Widths ........................... 7'', 9'', 12'' and 18''

Lengths .......................... 50' and 150'

Accessories f or Flashdek

Part Number Descriptions1175173 1/4-14 x 1-1/8'' Scots® Teks®/1

250 pieces needed for 50 feet ofFlashdek material.

4040910 Chemseco Sikalfex® Sealant8 tubes needed for 50 feet of Flashdek material.

4042910 9'' Termination Strips.4041910 12'' Termination Strips.4043910 18'' Termination Strips.

4044910 Hypalon Splice Material3'' x 38''

FLASHDEKFlexib le Flashing System

Applications

RO

OF

FLA

SH

ING

AP

PLIC

AT

ION

SP

RO

DU

CT

RE

PO

RT

NO. 02716

The most unique fle xib le, weatherpr oof r oof flashing system.

Product FeaturesUnique aluminum edging design conforms to allroof panel configurations.

Based on a proprietary formulation of coatedpolyester Hypalon®.

Superb ozone, acid rain and ultraviolet resistantproperties.

Soil and stain resistant.

Excellent abrasion resistance.

-40˚F to +190˚F continous service temperaturerange.

Parapet Wall Stepped Roof Transition Wall Gambrell Roof Roof Penetrations

31

®

Description

7'' x 50’7'' x 150’9'' x 50’9'' x 150’

12'' x 50’12'' x 150’18'' x 50’18'' x 150’

Base KitPart Number

40709114071911405491140539114060911405991140669114065911

Flashdek®, Teks®, Scots® and Building Ideas That Work® are trademarks of ITW Buildex and Illinois ToolWorks Inc. Hypalon® is a registered trademark of the Dupont Co. Sikaflex® is a registered trademark of

Chemseco Corp.

Performance Data

FLASHDEK ... Simple and Easy to Install

STEP 1: Snap a chalk line providing a guide for applyingsealant.

STEP 2: Apply a continuous beadof sealant along chalk line.

STEP 3: Position top edge ofFlashdek over seal bead and installBuildex fasteners at 6” maximumintervals on top edge. Repeat steps1, 2, and 3 for the bottom edge.Provide enough slack in theFlashdek for expansion.

STEP 4: Apply additional sealantto both fastened edges for maxi-mum waterproof sealing.

Base Kit Contains:• Flashdek Material• 2 termination strips• 1 roll Hypalon® splice material

Selector Guide

FLASHDEK FLEXIBLE FLASHING SYSTEM

PROPERTY

Material

Color

Thickness (In.)

Weight (oz./Sq. Yd.)

Tensile Strength(Pounds per in. of width)Room Temp. (75±5˚)WarpFill

Water VaporTransmission Rating(gms/m2/24 hrs)

TEST METHOD

-------

-------

-------

-------

Federal STD 191Method 5100

ASTM-E-96

RESULTSHypalon coated

Polyester

Grey

.025±.002"

22.5±10%

250 lbs./in. minimum200 lbs./in. minimum

43.44g/m2/24 hrs.

PROPERTYU.L. Fire Resistance

Rating

Service TemperatureRange

Tear Resistance(Pounds per inch of width)WarpFill

Heat Aging7 days @ 190˚FChange Tensile WarpChange Tensile Fill

TEST METHOD

U.L.-94

-------

ASTM 2262

Federal STD 191Method 5850Method 5100Method 5100

RESULTS

U.L.-94HB

-40˚ to 190˚FContinuous

25 lbs. min.25 lbs. min.

10% Max. Loss10% Max. Loss



32


Appr ovals and ListingsMetro-Dade Approved #02-0311-03, ICBO Approved #3370, SBCCI Approved #9759 City of Los Angeles.

Product SpecificationsDiameter 3/16'' and 1/4''Thread Form Original notched Hi-Lo®

Point Type NailFinish Blue Climaseal®

Corr osion ResistanceKesternic h Results (DIN 50018, 2.0L)

• 30 Cycles - 10% or less red rustSalt Spra y Results (ASTM B117)

• 720 Hours - 10% or less red rust

Head Styles3/16'' Diameter: 1/4'' slotted hex washer head (HWH)1/4'' Diameter: 5/16'' slotted hex washer head (HWH)

3/16'' Diameter: #2 phillips flat head (PFH)1/4'' Diameter: #3 phillips flat head (PFH)

LIG

HT

TO

ME

DIU

MD

UT

YM

AS

ON

RY

AP

PLIC

AT

ION

SP

RO

DU

CT

RE

PO

RT

NO. 02717

The original masonr y anc hor that cuts threads intoconcrete , bric k or hollo w bloc k.

ApplicationsElectrical junction boxes and conduit clips to masonry.Wood headers and furring strips to masonry.

HVAC strapping to masonry.Plywood backer boards to masonry.Exterior insulation systems to masonry.

33

Product FeaturesFast installation ... drill a hole ... drive an anchor.

Packaged with one Tapcon “close tolerance” masonrydrill bit per 100 anchors. Also available in bulk packaging.Available in 3/16'' and 1/4'' diameters and in lengths 1-1/4'' - 6''.

Replaces small diameter expansion anchors, plugs and screws in light to medium duty applications.

No need to pre-spot holes ... and no inserts arerequired.

Reversible and removable ... can be installed close to an edge.

Installation ToolsCondrive 500® - Compact high speed installation tooldesigned for installation of Tapcon hex head andPhillips flat head anchors up to 3-3/4'' long.

Condrive 1000® - A multi-purpose tool designed for installation of Tapcon hex head and Phillips flat head anchors up to 3-3/4'' long.

Condrive 2000® - A highly-automated, high speed, one-step tool designed specifically for repetitive installationof hex head Tapcon anchors of lengths up thru 2-3/4''.

Buildex Condrive Tools are designed to specificallyinstall Tapcon Anchors and to fit standard hammerdrills.

BX

BX

TAPCONThe OriginalMasonr y Fastening System

®

Note: Indicated pull-out and shear failure values wereobtained in tests witnessed by Pittsburgh Testing Laboratorypersonnel. Designated holding power depends on thequality of the masonry material, depth of embedment andproper hole size. These figures are offered only as a guideand are not guaranteed in any way by Illinois Tool WorksInc. The figures indicate average ultimate pull-out and shearfailure values. A safety factor of 4:1 or 25% of ultimate pull-out value is generally accepted as a safe working load.However, reference should always be made to applicablecodes for the specific safe working ratio. All values arebased on close tolerance holes drilled with Buildex Tapcon®

carbide drill bits. Performance of the Tapcon anchor mayvary in extremely hard concrete aggregates. Consult your Buildex representative for further information.

As in the case with all applications, Buildex can only suggest typical fasteners for typical applications and that the connection design is the sole responsibility of the Building Design Engineer, Architect or otherwise responsible personcharged with the design of the connection. For further product information, please contact the nearest Authorized BuildexDistributor or the Buildex Technical Service Department at 1-800-323-0720.

Selector Guide

Performance Data

PFH HWH3169407 3139407 3/16 x 1-1/4'' 5/32 x 3-1/2" 3095910 0 - 1/4" • Mounting brackets; control panels; cable clamps, conduit3183407 3153407 1/4 x 1-1/4" 3/16 x 3-1/2" 3098910 0 - 1/4" clips, junction switch and control boxes.

3171407 3141407 3/16 x 1-3/4" 5/32 x 3-1/2" 3095910 1/4 - 3/4"• 1/2'' or 3/4'' plywood backer boards; mounting brackets;

3185407 3155407 1/4 x 1-3/4" 3/16 x 3-1/2" 3098910 1/4 - 3/4"control panels; cable clamps; conduit clips, junction, switch and control box meters.

3173407 3143407 3/16 x 2-1/4" 5/32 x 4-1/2" 3096910 3/4" - 1-1/4" • 1 x 2 wood furring; 3/4'' plywood backer boards; metal3187407 3157407 1/4 x 2-1/4" 3/16 x 4-1/2" 3099910 3/4" - 1-1/4" safety grating.3175407 3145407 3/16 x 2-3/4" 5/32 x 4-1/2" 3096910 1-1/4" - 1-3/4"

• 2 x 4 wood nailers3189407 3159407 1/4 x 2-3/4" 3/16 x 4-1/2" 3099910 1-1/4" - 1-3/4"3177407 3147407 3/16 x 3-1/4" 5/32 x 5-1/2" 3097910 1-3/4" - 2-1/4"3191407 3161407 1/4 x 3-1/4" 3/16 x 5-1/2" 3100910 1-3/4" - 2-1/4"3179407 3149407 3/16 x 3-3/4" 5/32 x 5-1/2" 3097910 2-1/4" - 2-3/4" • Sill plates; 2 pieces of 2 x 4 or 2 x 6 to masonry.3193407 3163407 1/4 x 3-3/4" 3/16 x 5-1/2" 3100910 2-1/4" - 2-3/4" Insulation to masonry.3181407 3151407 3/16 x 4" 5/32 x 5-1/2" 3097910 2-1/2" - 3"3195407 3165407 1/4 x 4" 3/16 x 5-1/2" 3100910 2-1/2" - 3"3197407 3167407 1/4 x 5" 3/16 x 6-1/2" 3102910 3-1/4" - 4"3203407 3205407 1/4 x 6" 3/16 x 7-1/2" 3206910 4-1/4" - 5"

3379910 Condrive 500® For 3/16 and 1/4 diameter, Hex and Flat Heads, lengths up to 3-3/4"3103910 Condrive 1000® For 3/16 and 1/4 diameter, Hex and Flat Heads, lengths up to 3-3/4"3119910 Condrive 2000® For 3/16 and 1/4 diameter, Hex Head, lengths up to 2-3/4"

The minimum embedment requirement is 1" and the maximum embedment is 1-3/4".One drill bit is provided with every box of 100 pieces.*SDS with He x Drill Bits: 5/32" x 7" SDS Rotar y Hammer Drill Bit, Part Number 3311910;(*Condrive 1000 Onl y) 3/16" x 7" SDS Rotar y Hammer Drill Bit, Part Number 3101910.

PartPart FixtureNumber Description Drill Bit Number Thic kness Common Applications

Installation Guidelines:

Tapcon Anc hor s must be installed using all Builde x systemcomponents (T apcon Anc hor s, Condrive Tools and TapconDrill Bits) in or der to qualify f or ITW Builde x system suppor t.

Anc horDiameter

3/16''

1/4''

1''209 lbs.

406 lbs.

1-1/4''357 lbs.

615 lbs.

1-1/2''468 lbs.

851 lbs.

1-3/4''547 lbs.

984 lbs.

Depth of Embedment in Solid Material (inc hes)

PULLOUT IN HOLLO W BLOCK

Anc horDiameter

3/16''

1/4''

Anc horEmbedment

1-1/4''

1-1/4''

Shear Strength 3145 PSI HardRock Concrete

852 lbs.

1604 lbs.

Shear StrengthLightweight

Hollo w Bloc k

731 lbs.

1058 lbs.

SHEAR STRENGTH

Anc horDiameter

3/16''

1/4''

1''341lbs.

718 lbs.

1-1/4''581 lbs.

1138 lbs.

1-1/2''863 lbs.

1537 lbs.

1-3/4''1059 lbs.

1860 lbs.


PULLOUT IN CONCRETE (3145 PSI, cured 40 da ys) (lbs)

Test Number CH3932/Pittsburgh Testing Laboratories




©2002 Illinois Tool Works, Inc.34

THE ORIGINAL TAPCON ®

MASONRY FASTENING SYSTEM

Tapcon®, Condrive 500®, Hi-Lo®, Condrive 1000®, Condrive 2000®, Climaseal® and Building IdeasThat Work® are trademarks of ITW Buildex and Illinois Tool Works Inc.

CONDRIVE 500 GUIDELINES:STEP 1: Place drill adapter into 3/8'' or 1/2'' chuck ofstandard hammer drill. Place drill bit in drill adapterand tighten set screw. Drill hole a minimum of 1/4''deeper than Tapcon anchor is to be embedded.STEP 2: Phillips Heads may be installed using eitherside of sleeve. To install a 1/4 diameter Hex WasherHead Tapcon, use large opening side of sleeve (seesleeve label). To install a 3/16 diameter Hex WasherHead Tapcon, use small opening side of sleeve (seesleeve label). Slide opposite side of sleeve over drillbit and snap onto drill bit adapter. NOTE: If drivingHex Washer Head Tapcon, driver will automatically disengage. If driving Phillips HeadTapcon, care must be taken to ensure anchor is notoverdriven.STEP 3: Loosen set screw on side of drill adapterwith 1/8'' Hex Key. Do not remove completely.Replace old drill bit with new one. Align flat side withset screw and tighten screw. Do not overtighten.

CONDRIVE 1000 GUIDELINES:STEP 1: Place correct drill bit into driver adapter anddrill hole 1/4" deeper than depth of embedment.STEP 2: Slide Condrive Installation Tool sleeve overdrill bit. Snap hex head or Phillips Socket in place.STEP 3: Insert anchor in socket, position fixture to befastened, begin to drive Tapcon into pre-drilled hole.STEP 4: The anchor is fully set when the nosepiece ofthe Condrive Tool automatically disengages from thesocket and fixture is secured in place.

1349 West Bryn Mawr AvenueItasca, Illinois 60143630/595-3500 FAX: 630/595-3549www.itwbuildex.com


Diameter 1/4"Thread Form Original notched Hi-Lo®

Point Type NailFinish UltraShield™ or White UltraShield™

Corr osion ResistanceSalt Spra y Results (ASTM B117)Ultrashield ™

• 1100 Hours - 10% or less red rustWhite UltraShield ™

• 1500 Hours - No red rust

Head Styles

5/16" across flats hex with 5/8" diameter flange.

Installation Soc ket

DrivTru™ 5/16" HWH Socket System.Part Number 1513910.For specifications, see Product Report Number 01213.

LIG

HT

TO

ME

DIU

MD

UT

YM

AS

ON

RY

AP

PLIC

AT

ION

SP

RO

DU

CT

RE

PO

RT

NO. 02718

MAXI-SET TAPCON®

Masonr y Fastening System

Product FeaturesSame reliable performance and speed of installation as regular Tapcon.

Large 5/8" diameter flange provides more bearing surface and increases pullover resistance. High 5/16"hex head adds driving stability.

Compatible with DrivTru™ socket system. Improvesinstallation. Protects paint finish. See below.

UltraShield™ and White UltraShield™ long-life finishdeliver excellent corrosion resistance.

Optional bronze head paint over White UltraShield to match common aluminum extrusions.

Packaged in bulk. Masonry drill bits sold separately.


For Tapco n ® applications that require more anchor bearing surface .

ApplicationsShutters - protective and decorative.

Screened porch and pool enclosures.

Various sheet metal flashings.

Decorative wrought iron.

Wood nailers and plywood attachment.

35

MAXI-SET TAPCON ®MASONRY FASTENING SYSTEM

Selector Guide

Performance Data

Anc hor Anc hor Box Drill Bit Anc horDescription Part Number Quantity Part Number Finish

Maxi-Set Tapcon®, UltraShield™, Condrive 500®, Condrive 1000®, Driv-Tru™, Hi-Lo®, andBuilding Ideas That Work® are trademarks of ITW Buildex and Illinois Tool Works Inc.

1'' 1-1/4'' 1-1/2'' 1-3/4''

1/4'' 406 lbs. 615 lbs. 851 lbs. 984 lbs.

Depth of Embedment in Solid MaterialAnchorDiameter



1'' 1-1/4'' 1-1/2'' 1-3/4''

1/4'' 718 lbs. 1138 lbs. 1537 lbs. 1860 lbs.

Depth of Embedment in Solid Material (inc hes)AnchorDiameter

PULLOUT IN CONCRETE (3145 PSI, cured 40 da ys)


1/4'' 1-1/4'' 1604 lbs. 1058 lbs.

AnchorDiameter

AnchorEmbedment

Shear Strength3145 PSI HardRock Concrete


Hollo w Bloc k

SHEAR STRENGTH




36

Note: Indicated pull-out and shear failure values wereobtained in tests witnessed by Pittsburgh TestingLaboratory personnel. Designated holding power depends on the quality of the masonry material, depth of embedment and proper hole size. These figures areoffered only as a guide and are not guaranteed in any way by Illinois Tool Works Inc. The figures indicate average ultimate pull-out and shear failure values.A safety factor of 4:1 or 25% of ultimate pull-out value is generally accepted as a safe working load. However,reference should always be made to applicable codes forthe specific safe working ratio. All values are based onclose tolerance holes drilled with Buildex Tapcon® carbidedrill bits. Performance of the Tapcon anchor may vary inextremely hard concrete aggregates. Consult yourBuildex representative for further information.

As in the case with all applications, Buildex can only sug-gest typical fasteners for typical applications and that theconnection design is the sole responsibility of theBuilding Design Engineer, Architect or otherwise respon-sible person charged with the design of the connection.For further product information, please contact the near-est Authorized Buildex Distributor or the BuildexTechnical Service Department at 1-800-323-0720.

1/4 x 1-3/4"1/4 x 2-1/4"

Optional Items: Original Tapcon Carbide Drill Bits, Condrive Tools and Installation Soc kets.

Carbide Drill Bits Bit Standar d(Straight Shank) Part No. Tube Qty .

3/16 x 5-1/2'' 3100910 10 pcs.3/16 x 6-1/2'' 3102910 10 pcs.3/16 x 7-1/2'' 3206910 10 pcs. Carbide Drill Bits Bit Standar d

(SDS Shank) Part No. Tube Qty .3/16 x 7'' 3101910 1 piece

Drill Bit

*Available with bronze painted head over White UltraShield™.Note: 2-3/4'' and 3-1/4'' lengths are special orders. Contact customer service for leadtimes.

Condrive 500® Part No. 3379910 10 per box

Condrive 1000® Part No. 3103910 5 per boxNOTE: Must use a DrivTru™ Socket (Part No. 1513910) when using a Condrive Tool.

32950003364000 33650003383100*3384100*3408100*3409100*

3294000

1/4 x 2-3/4"

1/4 x 3-1/4"1/4 x 2-3/4"1/4 x 2-1/4"1/4 x 1-3/4"1/4 x 3-1/4"

1,000

1,0001,000

1,000750

1,0001,000

750

3/16 x 4-1/2"3/16 x 4-1/2"3/16 x 3-1/2"3/16 x 5-1/2"3/16 x 4-1/2"3/16 x 4-1/2"

3/16 x 3-1/2"

3/16 x 5-1/2" 3100910309991030999103098910310091030999103099910

3098910

White UltraShield™White UltraShield™White UltraShield™

White UltraShield™UltraShield™UltraShield™UltraShield™

UltraShield™

Product SpecificationsDiameter 1/4"Thread Form Original notched Hi-Lo®

Point Type NailFinish Silver Climaseal®

Head Style 5/16'' HWH (300 Series Stainless)

Corr osion ResistanceKesternic h Results (DIN 50018, 2.0L)

• 30 Cycles - 10% or less red rustSalt Spra y Results (ASTM B117)

• 720 Hours - 10% or less red rust

Head Styles

Installation Soc ket

DrivTru™ 5/16" HWH Socket System.Part Number 1513910.For specifications, see Product Report Number 01213.

EX

TE

RIO

RM

AS

ON

RY

AP

PLIC

AT

ION

SP

RO

DU

CT

RE

PO

RT

NO. 02719

SCOTS TAPCON

Product Features

300 Series Stainless Steel Head.

Pullout strength of carbon steel.

Integral washer design provides more bearingsurface.

Rubber EPDM sealing washer “locks-out” moisturefrom building interior.

Head paint available in white or bronze (extra charge).

Delivers up to 35% more holding power than “all-stainless” concrete anchors and costs less.

Provides the same strong holding power as regularand Maxi-Set Tapcon®.

Reduces job call-backs to replace “weathered”fasteners.

Premium concrete anc hor that combines the corr osionprotection of stainless steel with the holding po werof our regular carbon steel Tapcon ®.

ApplicationsShutters - Protective and Decorative.

Screened - Porch and Pool Enclosures.

Aluminum Fixtures.

Railings.

Metal Roofing.

Flexible Flashings.

® ®

37


SCOTS TAPCON EXTERIOR CONCRETE ANCHOR Product Report No. 02719

Selector Guide

Performance Data

Scots® Tapcon®, Maxi-Set Tapcon®, Hi-Lo®, Condrive 500®, Condrive 1000®, Climaseal®, DrivTru™, and Building Ideas That Work® are all trademarks of ITW Buildex and Illinois Tool Works Inc.

Optional Items: Original Tapcon Carbide Drill Bits, Condrive Tools and Installation Soc kets.

Carbide Drill Bits Bit Standar d(Straight Shank) Part No. Tube Qty .

3/16 x 5-1/2'' 3100910 10 pcs.

3/16 x 6-1/2'' 3102910 10 pcs.

3/16 x 7-1/2'' 3206910 10 pcs.Carbide Drill Bits Bit Standar d

(SDS Shank) Part No. Tube Qty .

3/16 x 7'' 3101910 1 piece

Anc horDiameter

1/4'' Dia.

1''Embedment

718 lbs.

1-1/4''Embedment

1138 lbs.

1-1/2''Embedment

1537 lbs.

1-3/4''Embedment

1860 lbs.

Pullout in Concrete (3145 PSI)

Anc horDiameter

1/4'' Dia.

Anc horEmbedment

1-1/4''

Concrete(3145 PSI)

1604 lbs.

Hollo wBloc k

1058 lbs.

Pullout in Hollo w Bloc kAnc hor

Diameter

1/4'' Dia.

1''Embedment

406 lbs.

1-1/4''Embedment

615 lbs.

1-1/2''Embedment

851 lbs.

1-3/4''Embedment

984 lbs.

Shear Strength

Note: Indicated pull-out and shear failure values were obtained intests witnessed by Pittsburgh Testing Laboratory personnel.Designated holding power depends on the quality of the masonrymaterial, depth of embedment and proper hole size. These figuresare offered only as a guide and are not guaranteed in any way byIllinois Tool Works Inc. The figures indicate average ultimate pull-outand shear failure values. A safety factor of 4:1 or 25% of ultimatepull-out value is generally accepted as a safe working load.

However, reference should always be made to applicable codes for the specific safe working ratio. All values are based on close tolerance holes drilled with Buildex Tapcon® carbide drill bits.Performance of the Tapcon anchor may vary in extremely hard concrete aggregates. Consult your Buildex representative for further information.

As in the case with all applications, Buildex can only suggest typical fasteners for typical applications and that the connection design isthe sole responsibility of the Building Design Engineer, Architect orotherwise responsible person charged with the design of the connection. For further product information, please contact thenearest Authorized Buildex Distributor or the Buildex TechnicalService Department at 1-800-323-0720.


38

Condrive 500™ Part No. 3379910 10 per box

Condrive 1000® Part No. 3103910 5 per box

3358407 100 / 1,000 3/16" x 3-1/2" 3098910

3359407 100 / 1,000 3/16" x 4-1/2" 3099910

Silver Climaseal®

Long-Life Coating

White or BronzeCall For Quote

Anc hor Anc hor Box / Ctn Drill Bit Anc hor Head Description Part Number Qty / Qty

Drill Bi t *Part Number Finish Paint

1/4 x 1-3/4"Fully Threaded

1/4 x 2-1/4"

® ®

NOTE: Must use a DrivTru™ Socket (Part No. 1513910) when using a Condrive Tool.

Premium masonr y anc hor that pr ovides the corr osion

protection of 410 Stainless Steel and the perf ormance of our

original carbon Tapcon ®.

CO

RR

OS

IVE

EN

VIR

ON

ME

NT

MA

SO

NR

YA

PP

LICA

TIO

NS

PR

OD

UC

TR

EP

OR

TN

O. 02720

410 STAINLESSSTEEL TAPCON Masonr y Fastening System

Product Features

410 Stainless Steel for added corrosionprotection.

Fast installation ... drill a hole ... drivean anchor.

Cuts threads into concrete, brick and hollowblock.

Available in 1/4 diameter in lengths 1-1/4'' - 3-3/4''.

Buildex head marking for easy field identification.

Reversible and removable ... can be installedclose to an edge.

Optional white or bronze head paint to matchcommon aluminum extrusions.

100 count packaging.

Product SpecificationsDiameter 1/4’’Thread Form Original Notched Hi-Lo®

Point Type NailMaterial 410 Stainless SteelFinish ClimaShield™

Salt Spray Results (ASTM B117 )• 1600 Hours - NO RED RUST.

HWH 5/16'' Hex Washer Head

PFH #3 Phillips Flat Head

ApplicationsShutters - protective and decorative

Windows

Screened porch and pool enclosures

Railings - safety and decorative

Exterior fixtures

Marine

Agricultural

®

Head Styles

Corr osion Resistance

39

Appr ovals and ListingsMetro-Dade Approved #02-0311-03, SBCCI Approved #9759A City of Los Angeles.

1349 West Bryn Mawr AvenueItasca, Illinois 60143630/595-3500 FAX: 630/595-3549 ©2002 Illinois Tool Works Inc.www.itwbuildex.com

Tapcon®, Hi-Lo®, Condrive 500®, Condrive 1000®, Condrive 2000®, ClimaShield™, Building IdeasThat Work™, are all trademarks of ITW Buildex and Illinois Tool Works Inc.

410 STAINLESS STEEL TAPCON® MASONRY FASTENING SYSTEM Product Report No. 02720

Performance Data

Selector Guide Part Number FixturePFH HWH Thic kness

3373907 3367907 1/4 x 1-1/4'' 3098910 3/16 x 3-1/2'' 0-1/4''

3374907 3368907 1/4 x 1-3/4'' 3098910 3/16 x 3-1/2'' 1/4-3/4''

3375907 3369907 1/4 x 2-1/4'' 3099910 3/16 x 4-1/2'' 3/4-1-1/4''

3376907 3370907 1/4 x 2-3/4'' 3099910 3/16 x4-1/2'' 1-1/4''-1-3/4''

3377907 3371907 1/4 x 3-1/4'' 3100910 3/16 x 5-1/2'' 1-3/4''-2-1/4''

3378907 3372907 1/4 x 3-3/4'' 3100910 3/16 x 5-1/2'' 2-1/4''-2-3/4''

3379910 Condrive 500® For 1/4'' diameter, hex and flat heads lengths up to 3-3/4''.

3103910 Condrive 1000® For 1/4'' diameter, hex and flat heads lengths up to 3-3/4''.

3119910 Condrive 2000® For 1/4'' diameter hex head, lengths up to 2-3/4''.

Tapcon Anc hor s must be installed using all Builde x system components (T apcon Anc hor s, Condrive Tools, andTapcon Drill Bits) in or der to qualify f or ITW Builde x system suppor t.

Installation Guidelines Using Condrive 500 ®

STEP 1: Place drill adapter into 3/8'' or 1/2'' chuck of standard hammer drill. Place drill bit in drilladapter and tighten set screw. Drill hole a minimum of 1/4'' deeper than Tapcon anchor is to beembedded.STEP 2: Phillips Heads may be installed using either side of sleeve. To install a 1/4 diameter HexWasher Head Tapcon, use large opening side of sleeve (see sleeve label). To install a 3/16 diameter Hex Washer Head Tapcon, use small opening side of sleeve (see sleeve label). Slideopposite side of sleeve over drill bit and snap onto drill bit adapter. NOTE: If driving Hex WasherHead Tapcon, driver will automatically disengage. If driving Phillips Head Tapcon, care must betaken to ensure anchor is not overdriven.

STEP 3: Loosen set screw on side of drill adapter with 1/8'' Hex Key. Do not remove completely.Replace old drill bit with new one. Align flat side with set screw and tighten screw. Do not over-tighten.

Note: Designated holding power depends on the quality of the masonry material, depth of embedment and proper hole size. These figures are offered only as a guide and are not guaranteed in anyway by Illinois Tool Works Inc. The figures indicate average ultimate pull-out and shear failure values. A safety factor of 4:1 or 25% of ultimate pull-out value is generally accepted as a safe workingload. However, reference should always be made to applicable codes for the specific safe working ratio. All values are based on close tolerance holes drilled with Buildex Tapcon® carbide drill bits.Performance of the Tapcon anchor may vary in extremely hard concrete aggregates. Consult your Buildex representative for further information.

As in the case with all applications, Buildex can only suggest typical fasteners for typical applications and that the connection design is the sole responsibility of the Building Design Engineer,Architect or otherwise responsible person charged with the design of the connection. For further product information, please contact the nearest Authorized Buildex Distributor or the BuildexTechnical Service Department at 1-800-323-0720.

Anc horDiameter

1/4''

Anc horEmbedment

1-1/4''

Shear Strength 3145 PSI HardRock Concrete

1622


Hollo w Bloc k

1218

SHEAR STRENGTH

Anc horDiameter

1/4''

1''

1381

1-1/4''

1616

1-1/2''

2041

1-3/4''

2332


PULLOUT IN CONCRETE (3145 PSI, cured 40 da ys) (lbs)

Tapcon Anc hor s must be installed using all Builde x systemcomponents (T apcon Anc hor s, Condrive Tools and Tapcon Drill Bits) in or der to qualify f or ITW Builde x system suppor t.


• Mounting brackets and control panels.

• 1/2'' or 3/4'' plywood backer boards; mounting brackets; control panels; cable clamps; conduit clips; junction, switch and control box meters.

• Metal safety gratings, 2 x 4 wood nailers.

1/4''

Depth of Embedmentin Solid Materials (Inc hes)

1-1/4''

754

Anc horDiameter

Installation Guidelines Using Condrive 1000 ®

STEP 1: Place correct drill bit into driver adapter and drill hole 1/4" deeper than depth of embedment.

STEP 2: Slide Condrive Installation Tool sleeve over drill bit. Snap hex head or Phillips Socket in place.

STEP 3: Insert anchor in socket, position fixture to be fastened, begin to drive Tapcon into pre-drilled hole.

STEP 4: The anchor is fully set when the nosepiece of the Condrive Tool automatically disengagesfrom the socket and fixture is secured in place.

Common ApplicationsDescription Drill Bit

• Marine and agricultural.

• Sills, plates 2 pieces of 2 x 4 or 2 x 6 to masonry.Insulation to masonry.

Drill BitPart No.

40

CORROSIVE ENVIRONMENT

41

Product Features

No hole preparation necessary; pre-drills ownsmall precise hole in gypsum wallboard.

Replaces plastic plugs and toggles.

Deep thread design provides strong engagementin 3/8'', 1/2'' and 5/8'' gypsum wallboard.

Installs quickly and easily with a phillips screw-driver or square drive bit.

Full range of anchors to cover all wall fasteningapplications.

Available in corrosion resistant, non-conductivewhite nylon.

Can be easily backed-out.

Low profile head.

Single point designs for clean cutting installation.

E-Z EST™ - no screws needed -- attachmentsthrough gypsum and wood.

DR

YW

ALL

AN

CH

OR

AP

PLIC

AT

ION

SP

RO

DU

CT

RE

PO

RT

NO. 02721

E-Z PRODUCTSSelf-Drilling Dr ywall Anc hor s

Single P oint Designs!!


The original!Fast and easy self-drilling anc hor s.

E-Z Ancor ®, E-Z EST™, E-Z Mini Ancor ®, E-Z Ancor Lite ™,

E-Z Ancor Plastic Plus ™, E-Z Toggle™

Product Material ........ Zinc die castNylon

Drilling Capacity ....... 3/8'', 1/2'' and 5/8'' gypsum wallboard

E-Z EST™ also penetrates w ood!!

ApplicationsElectrical FixturesThermostatsHVAC FixturesPlumbing FixturesBathroom AccessoriesShelving and SupportsMirrorsPicture FramesBrackets

Plaques and AwardsCloset OrganizersCoat RacksCurtain RodsSignsBulletin BoardsControl SystemsDecorative Wall Hangings

Office Material HoldersSmoke DetectorsClocksKitchen AccessoriesDoorbellsTelecommunications EquipmentChalk BoardsRemote Control Boxes

N E W

N E W

N E W

N E W

42

Light Duty E-Z EST™

Light Duty PlasticLight Duty ZincMedium DutyHeavy Duty

AccommodatesSheet MetalScrew Size

Zinc 5037902 100 count 1/16'' No Screw Needed

5006902 100 count #6

Zinc 5033902 100 count

Zinc 5000902 100 count #6, #7 or #8

White Nylon 5035902 100 count 3/4'' #6, #7 or #8

50 count50 #8 x 2-1/8'' Pan SMS

50 count - 50 #8 x 2-1/8''Large Washer Face SMS

1349 West Bryn Mawr AvenueItasca, Illinois 60143630/595-3500 FAX: 630/595-3549www.itwbuildex.com ©2002 Illinois Tool Works Inc.

These performance values are averages obtained under laboratory conditions. Note that these values will change depending on age, moisture content and surface treatmentof the drywall (gypsum) material. Appropriate safety factors should be applied to these values for design purposes.

SELF-DRILLING DRYWALL ANCHORS Product Report No. 02721

E-Z

Togg

le™

E-Z

Anco

r®

E-Z

Min

iAn

cor™

E-Z

Anco

rLit

e™

9/16'' 2-1/2''

Anc hor Description

Performance Data

Selector GuideE-Z PRODUCTS

PartNumber Quantity

Anc horMaterial

Maximum FixtureThic kness

Heav

y Du

tyM

ediu

m D

uty

Ligh

t Dut

y

3/8" 1-5/16"

1/2" 1-5/8"

7/16" 1-1/4"

3/4''

3/4''

5014901

50179011/2''Zinc

White Nylon

E-Z Ancor®, E-Z Ancor Lite™, E-Z Mini Ancor®, Plastic Plus™, E-Z EST™, E-Z Toggle™, andBuilding Ideas That Work® are trademarks of ITW Buildex and Illinois Tool Works Inc.


1. Place #2 Phillips screwdriver into recess of E-Z Ancor Lite , E-Z Mini Ancor, E-Z Ancor or E- Z Ancor Plastic Plus. For E-Z EST place fixture and turn anchor clockwise until it is seated against fixture.

2. Press into drywall while turning the anchorclockwise until it is seated flush with wall.

3. Place fixture in position over installed E-ZAncor Lite, E-Z Mini Ancor, E-Z Ancor, or

Plastic Plus. Insert screw with screw driver.Tighten fixture in place.

1. Place #2 Phillips screwdriver into recess of E-Z Toggle. Press into drywall while turning the anchor clockwise until it is seated flush with wall and arrows on head are parallel to stud.

2. Place fixture in position over installed E-Z Toggle. Insert screw.

3. Turn screw until tight.. The clamp will move back against the drywall as the screw turned.

3/8''2025304070

1/2''2530405085

5/8''35405075

150

3/8''708090

135200

1/2''8090

110150230

5/8''110120140200300

Pullout(ultimate a verage lbs.)

Gypsum Thic kness

Shear(ultimate a verage lbs.)

Gypsum Thic kness

E-Z

Anco

r®

Plas

ticPl

us™

1/2" 1-5/8"

#6, #7 or #8

#8

Light Duty & Medium Duty E-Z Ancor s and E-Z EST Heavy Duty E-Z Toggle

New and Impr oved Single P oint Designs

NEW

E-Z EST™

9/32" 1-1/32''

3/4''

ROCK-ONCement Boar d Fastener s

CE

ME

NT

BO

AR

DA

PP

LICA

TIO

NS

PR

OD

UC

TR

EP

OR

TN

O. 02722

Product FeaturesRock-On

Rib design under head countersink into dense materialwhile preventing stripouts.

Two point types for steel and wood applications.

Larger head diameter increases board surface contact forgreater pullover resistance.

Backer-OnGimlet points starts easily - no predrilling.

Serrated thread design provides reduced installation torqueand superior holding power.

Rib design under head countersinks into dense materialwhile preventing stripouts.

#2 square drive prevents bit from slipping.

Product SpecificationsRock-OnDiameter ...................... #8; #9Thread Form ............... 8-18; 9-15 Hi-Lo

Drill P oint .................... #8 Type S-12®; #9 Type “S”

Head Style .................. Wafer Head with countersinking ribs

Finish ......................... Climacoat®

Backer-OnDiameter ...................... #10Thread Form ............... 10-10 Serrated

Drill P oint .................... Gimlet

Head Style .................. Wafer Head with countersinking ribs

Finish ......................... Long life epoxy topcoat/zinc plating.

Cement-type boards orany dense sheathings to

steel or wood studs.

Plywood to steel orwood studs.

Wire lath to steel orwood studs.

Hardie Fiber CementBackerboard

Applications

High perf ormance rib design is still the best!!!

Corr osion ResistanceRock-OnKesternic h Results (DIN 50018, 2.0L)• 20 Cycles - 10% or less red rustSalt Spra y Results (ASTM B117)• 500 hours - 10% or less red rust

Backer-OnKesternic h Results (DIN 50018, 2.0L)• 10 Cycles - 10% or less red rustSalt Spra y Results (ASTM B117)• 1,400 hours - 10% or less red rust

43

™

BACKER-ONFiber Cement Bac kerboar dFastener sRecogniz ed f or use with HARDIB ACKER ®

fiber cement bac kerboar d.

™

Part Material

Number Length Attac hment Rang e Applications

Hi-Lo ® Rock-On

2151500*r 9 x 1-1/4'' Up to 3/4'' Material Thickness to Wood; • Cement Board to3/8'' - 1'' Material Thickness to Steel Wood or Light Gauge

2153500*r 9 x 1-5/8'' Up to 1-1/8'' Material Thickness to Wood; Steel 26-20 Gauge3/8'' - 1-3/8'' Material Thickness to Steel

2155500 9 x 2-1/4'' Up to 1-3/4'' Material Thickness to Wood;1'' to 1-7/8'' Material Thickness to Steel

S-12® Rock-On2156500* 8 x 1-1/4'' 3/8'' to 3/4'' Material Thickness2159500* 8 x 1-5/8'' 3/8'' to 1-1/4'' Material Thickness2139500 8 x 2-1/4'' 1'' to 1-7/8'' Material Thickness

Backer-on ™

2406000 10 x 1-1/4'' Up to 3/4'' Material Thickness to Wood;3/8'' - 1'' Material Thickness to Steel

CEMENT BOARD FASTENERSSelector Guide

Performance Data

Hi-LoBacker-On™

1/2''223

-

3/4''312436

1''555780

1-1/4''676

-

Wood (Embedment)#2 SPF 2 X 4

S-12

Hi-Lo

Backer-On™

26

120

163

271

24

191

242

371

22

239

314

457

20

285

370

615

18

470

-

-

16

663

-

-

14

910

-

-

12

1424

-

-

Pullout Values in Steel (Gaug e)

12

.105''

14

.075''

16

.060''

18

.048''

20

.036''

22

.030''

24

.024''

26

.018''

Gauge No.

Decimal Equivalent

Sheet Steel Gaug es

Installation GuidelinesA standard screwgun with a depth sensitivenosepiece should be used to install cement board fasteners. For optimal fastener performance, the screwgun should be a minimum of 4 amps and have a RPM range of 0-2500.Adjust the screwgun nosepiece to properly seat the fastener.

Worn or damaged bit tips should be replaced.The fastener is fully seated when the head is flushwith the work surface.Overdriving may result in torsional failure of the fastener or stripout of the substrate.The fastener must penetrate beyond the metal structure a minimum of 3 pitches of thread.

Rock-On™, Backer-on™, Climacoat®, Hi-Lo®, S-12® and Building Ideas That Work®

are trademarks of ITW Buildex and Illinois Tool Works Inc.Hardibacker® is a registered trademark owned by James Hardie Research Pty Limited.

The values listed are ultimate averages achieved under laboratory conditions andapply to Buildex manufactured fasteners only. Appropriate safety factors should beapplied to these values for design purposes.


44

®

®

®


*Fully Threaded. r Now available in small box packaging.N E W

• Cement Board to SteelStuds 20-12 Gauge

• Backer BoardN E W

Seats Dec-King® screws flush with the deckwithout damaging the wood.

Eliminates angle driving, underdriven or over-driven screws, screw wobble, camouts andmarring of the deck surface.

Increases productivity and improves the quality of work; providing significant labor and installed cost savings.

Stand-up operation reduces operator fatigue and increases productivity.

EX

TE

RIO

RW

OO

DA

PP

LICA

TIO

NS

AN

DIN

STA

LLAT

ION

TO

OL

PR

OD

UC

TR

EP

OR

TN

O. 02723

DEC-KINGExterior Wood Scre ws

Product Features

Coated with Climacoat® for maximum resistance to corrosion, staining and streaking inside the lumber and on the deck.

Outperforms all zinc based platings in treatedwood.

Pullout strength is superior over nails.

Eliminates wood splitting, nail pops, hammermarks and bent nails.

Now available in both #2 Phillips and #2 Square Drive.

Dec-U-Drive Stand-Up Installation Tool

Corr osion Resistance

Kesternic h Results (DIN 50018, 2.0L)• 20 Cycles - 10% or less red rust

Salt Spra y Results (ASTM B117)• 500 hours - 10% or less red rust

®

45

TM

N E W

DEC-KING EXTERIOR WOOD SCREWS

Selector Guide

Performance Data

#2 Square Drive #2 Phillips

6 x1-1/4'' ------ 2176500 1'' x 4'' or 1'' x 6'' Base Trim; Lattice

6 x 1-5/8'' 2178500 2136500 1'' x 4'' or 1' x 6'' Base Trim; Ballisters; Lattice

7 x 2'' 2179500 2138500 5/4'' x 4'' or 5/4'' x 6'' Radius Edged Decking;1'' x 4'' or 1'' x 6'' Base Trim; Ballisters; Lattice

5/4'' x 4'' or 5/4'' x 6'' Radius Edged Decking8 x 2-1/2'' 2180500 2140500 2'' x 4'' or 2'' x 6'' Decking

2'' x 6'' or 2'' x 8'' Rail Cap or Base Trim

8 x 3'' 2181500 2141500 2'' x 4'' or 2'' x 6'' Decking2'' x 6'' or 2'' x 8'' Rail Cap or Base Trim

10 x 3-1/2'' 2182500 2142500 2'' x 4'' or 2'' x 6'' Decking2'' x 6'' or 2'' x 8'' Rail Cap or Base Trim

Dec-U-Drive Tool 2132910

#2 Square Drive Bit 2388910

Description

6 x 1-1/4"

6 x 1-5/8''

7 x 2''

8 x 2-1/2''

8 x 3''

10 x 3-1/2''

1/2''

182

182

189

186

186

241

3/4''

329

329

318

290

290

386

1''

422

422

440

502

502

522

1-1/4''

—

620

630

630

645

721

Pullout Values (a verage pounds ultimate)Embedment 2'' x 4'' Stud Grade S.Y . Pine

Note: The values listed are ultimate averages achieved under laboratory conditions. An appropriate safety factorshould be applied in these values to achieve a design value.

Dec-King®, Dec-U-Drive™, Climacoat® and Building Ideas That Work® are trademarks of ITW Buildex and Illinois Tool Works Inc.

46



®

Description ApplicationsPart Number

#2 Square Drive #2 Phillips

N E W

EX

TE

RIO

RIN

SU

LAT

ED

FIN

ISH

SY

ST

EM

AP

PLIC

AT

ION

SP

RO

UD

CT

RE

PO

RT

NO. 02724

GRID-MATE PBMechanical F astener s

Product FeaturesPatented “closure fingers” keep coating out ofcontact with fastener head - no sink marks orbleed throughs.

Strong polypropylene material provides excellentimpact resistance and service life in temperatureextremes.

“Keying'' holes and textured surface form a strongmechanical bond with coating.

Available assembled with Buildex long life fasteners to speed installation.

Recessed core allows fastener head to “float” - nohead pops or thermal bridging.

Designed for use with broad range of Buildexfasteners to attach to steel, wood, concrete ormasonry.

Large 2'' diameter resists and distributes wind-loads for a secure system

Climacoat® and Climaseal® long-life coatedfasteners are backed by a 20 year warranty.


The ultimate fastening system f or all Polymer Based (PB) Barrierand Water Mana ged EIFS

Diameter 2'' RoundMaterial White polypropylene

Applications

Attaching expanded polystyrene insulation to allsubstrates for all Polymer Based (PB) ExteriorInsulated Finish Systems (EIFS).

Attaching dense blanket or rigid insulation forparking garages, fireproofing, foundation wallsand soundproofing.

Corr osion Resistance ... Climacoat ®

Kesternich Results (DIN 50018, 2.0L)• 20 Cycles - 10% or less red rustCorr osion Resistance ... Climaseal ®

Kesternich Results (DIN 50018, 2.0L)• 30 Cycles - 10% or less red rust

Salt Spray Results (ASTM B117)• 500 hours - 10% or less red rust.


Part Number 2189900

Made in U.S.A.

Now Availab le Assemb led

Assembled(See back page)

47

™

Industr y Part Insul. Screw CartonNumber Number Thic kness Length Qty.

S2 2363500 1-1/2” 2” 1000S3 2364500 2” 2-5/8” 1000S4 2365500 2-1/2” 3” 1000S5 2366500 3, 3-1/2” 4” 500

GRID-MATE™ PB Product Report No. 02724SELECTOR GUIDE

1349 West Bryn Mawr AvenueItasca, Illinois 60143630/595-3500 FAX: 630/595-3549 ©2002 Illinois Tool Works, Inc.www.itwbuildex.com

Grid-Mate™ PB, Climaseal®, Climacoat®, S-12®, Hi-Lo®, Tapcon® and Building Ideas that Work®

are all trademarks of ITW Buildex and Illinois Tool Works Inc.

Tools and TechniquesUse a 0-2500 RPM, 5 amp min. rated screwgun or cordless drill toinstall fasteners to wood and steel substrates. Use a hammerdrill orrotary hammer to install Tapcon masonry anchors.

Seat Grid-Mate PB washers flush with or maximum 1/16'' below insulation surface. Overdriving Grid-Mates may damage the washer and insulation.

Fasteners must penetrate steel substrates a minimum of 3 pitches ofthreads.

Replace worn or damaged bit tips to prevent damage to fastenerhead and its finish.

Consult EIFS system manufacturers specifications for appropriate fastener spacing.

Performance Data Pullout Values(Average lbs. ultimate)

FastenerWood/Light Metal

(Hi-Lo)

Plywood OSB Lumber (Embedment)1/2'' 5/8'' 3/4'' 1/2'' 1/2'' 3/4'' 1'' 1-1/4''298 432 633 208 183 304 441 652

Wood Applications

Steel Applications TapconDiameter

3/16''

Concrete/Masonr y Applications3000 PSI Concrete

EmbedmentHollo w Bloc kEmbedment

The values listed are ultimate averages achieved under laboratory conditions andapply to Buildex manufactured fasteners only. Appropriate safety factors should beapplied to these values for design purposes. Wind-load test results also availableupon request.

Part Carton CartonNumber Description Quantity Weight

2189900 Grid-Mate PB Washer 1000 11 lbs.

Washer s

WOOD/LIGHT METALFor use with plywood, OSB, dimensional lumber

and light gauge metal (26 gauge - 20 gauge).

STEEL FRAMINGFor use with steel framing from 20 gauge - 12 gauge.

MASONRYFor use with brick, block and concrete.

• #2 Phillips Bugle Head.• Climacoat® Finish.• Hi-Lo® Thread Form.

• #2 Phillips Bugle Head.• Climacoat® Finish.• S-12® Drill Point.

Fastener s

1'' 1-1/4'' 1-1/2' 1-3/4'' 1'' 1-1/4'' 1-1/2' 1-3/4''341 581 863 1059 209 357 468 547

48

Industr y Part Insul. Screw CartonNumber Number Thic kness Length Qty.WLM1 2349500 1” 1-5/8” 1000WLM2 2350500 1-1/2” 2” 1000WLM3 2351500 2” 2-1/2” 1000WLM4 2358500 2-1/2” 3” 1000WLM5 2359500 3, 3-1/2” 4” 500

Part Car ton Car tonNumber Description Qty Wgt.2311500 7 x 1-5/8'' 5000 232312500 8 x 2'' 3500 282313500 8 x 2-1/2'' 2500 212314500 8 x 3'' 2000 202315500 8 x 4'' 1000 122316500 10 x 5'' 1000 232317500 10 x 6'' 1000 27

Part Car ton Car tonNumber Description Qty Wgt.2321500 6 x 1-5/8'' 5000 252318500 6 x 2'' 3500 282319500 8 x 2-5/8'' 2500 262320500 8 x 3'' 2000 242322500 10 x 4'' 1000 212323500 10 x 5'' 1000 26

Part Car ton Car tonNumber Description Qty Wgt.3171407 3/16 x 1-3/4'' 100/1000 103173407 3/16 x 2-1/4'' 100/1000 123175407 3/16 x 2-3/4'' 100/1000 153177407 3/16 x 3-1/4'' 100/1000 173181407 3/16 x 4'' 100/1000 21

• 10 Carbide Bits Per 1000 Piece Carton.

Assemb led Washer s and F astener s


(Hi-Lo)

Steel (S-12)

26

129

-

24

178

-

22

244

-

20

277

296

18

-

471

16

-

679

14

-

847

12

-

1225

Sheet Steel Gaug es

EX

TE

RIO

RIN

SU

LAT

ED

FIN

ISH

SY

ST

EM

AP

PLIC

AT

ION

SP

RO

DU

CT

RE

PO

RT

NO. 02725

GRID-MATEMechanical F astener s

Product FeaturesLow profile design - seats flush without damagingthe insulation or mesh.

“Keying Windows” and textured face provides multiple areas that create a strong mechanicalbond with all coatings.

Strong polypropylene material provides excellentimpact resistance and service life in temperatureextremes.

Designed to be used with Buildex fasteners toprovide optimum seating and pullover resistancein steel, wood, concrete or masonry.

Climacoat® and Climaseal® long life coatedfasteners resist corrosion and surface bleedthrough.

Available with stem for time-saving pre-spottingof the plate to isocyanurate insulation.

Available assembled with fasteners to speedinstallation.


The original mec hanical fastening system f or Polymer Modified (PM) and Modified PB EIFS.

Diameter 1-3/4'' Plate1-3/4'' Plate with stem

Material White polypropylene

Applications

All Polymer Modified (PM) Systems.

Modified Stucco Systems.

Expanded lath over rigid insulation.

Fabric mesh over rigid insulation.

Wire mesh over rigid insulation.

Attaching rigid insulation to wood, steel, masonry,or concrete.

™

Made in U.S.A.

Part No. 2115900 Part No. 2117900Assembled(See back page)

Now Availab le Assemb led

Corr osion Resistance ... ClimacoatKesternich Results (DIN 50018, 2.0L)• 20 Cycles - 10% or less red rustCorr osion Resistance ... ClimasealKesternich Results (DIN 50018, 2.0L)• 30 Cycles - 10% or less red rust



49


GM4 2355500 1” 1-5/8” 1000

GRID-MATE™ Product Report No. 02725SELECTOR GUIDE

Tools and TechniquesUse a 0-2500 RPM, 5 amp min. rated screwgun or cordlessdrill to install fasteners to wood and steel substrates. Use ahammerdrill or rotary hammer to install Tapcon masonry anchors.

Seat Grid-Mate washers flush with or maximum 1/16'' below insulation surface. Overdriving Grid-Mates may damage the washer and insulation.

Fasteners must penetrate steel substrates a minimum of 3pitches of threads.

Replace worn or damaged bit tips to prevent damage to fastenerhead and its finish.

Consult EIFS system manufacturers specifications for appropriate fastener spacing.

Performance Data Pullout Values(Average lbs. ultimate)

Wood Applications

Steel ApplicationsConcrete/Masonr y Applications

The values listed are ultimate averages achieved under laboratory conditions andapply to Buildex manufactured fasteners only. Appropriate safety factors should beapplied to these values for design purposes. Wind-load test results also availableupon request.

Fastener s

Part Carton CartonNumber Description Quantity Weight

2115900 Grid-Mate 1000 4.5 lbs.2117900 Grid-Mate with Stem 1000 5.0 lbs.

Washer s

WOOD/LIGHT METALFor use with plywood, OSB, dimensional lumber

and light gauge metal (26 gauge - 20 gauge).

STEEL FRAMINGFor use with steel framing from 20 gauge - 12 gauge.

MASONRYFor use with brick, block and concrete.

• #2 Phillips Bugle Head.• Climacoat® Finish.• Hi-Lo® Thread Form.

• #2 Phillips Bugle Head.• Climacoat® Finish.• S-12® Drill Point.

Part Carton CartonNumber Description Qty. Wgt.2321500 6 x 1-5/8'' 5000 252318500 6 x 2'' 3500 282319500 8 x 2-5/8'' 2500 262320500 8 x 3'' 2000 242322500 10 x 4'' 1000 212323500 10 x 5'' 1000 26

Part Carton CartonNumber Description Qty. Wgt.2311500 7 x 1-5/8'' 5000 232312500 8 x 2'' 3500 282313500 8 x 2-1/2'' 2500 212314500 8 x 3'' 2000 202315500 8 x 4'' 1000 122316500 10 x 5'' 1000 232317500 10 x 6'' 1000 27

Part Car ton Car tonNumber Description Qty Wgt.3171407 3/16 x 1-3/4'' 100/1000 103173407 3/16 x 2-1/4'' 100/1000 123175407 3/16 x 2-3/4'' 100/1000 153177407 3/16 x 3-1/4'' 100/1000 173181407 3/16 x 4'' 100/1000 21

• 10 Carbide Bits Per 1000 Piece Carton.


(Hi-Lo)

Plywood OSB Lumber (Embedment)1/2'' 5/8'' 3/4'' 1/2'' 1/2'' 3/4'' 1'' 1-1/4''298 432 633 208 183 304 441 652


(Hi-Lo)

Steel (S-12)

26

129

-

24

178

-

22

244

-

20

277

296

18

-

471

16

-

679

14

-

847

12

-

1225

Sheet Steel Gaug es

TapconDiameter

3/16''

1/4''

1''

341

718

1-1/4''

581

1138

1-1/2''

863

1537

1-3/4''

1059

1860

1''

209

406

1-1/4''

357

615

1-1/2''

468

851

1-3/4''

547

984

3000 PSI ConcreteEmbedment

Hollo w Bloc kEmbedment

Assemb led Washer s and F astener s

1349 West Bryn Mawr AvenueItasca, Illinois 60143630/595-3500 FAX: 630/595-3549 ©2002 Illinois Tool Works, Inc.www.itwbuildex.com

Grid-Mate™, Climaseal®, Climacoat®, S-12®, Hi-Lo®, Tapcon® and Building Ideas that Work® areall trademarks of ITW Buildex and Illinois Tool Works Inc.

50


GM1 2352500 1” 1-5/8” 1000

NORTHWESTSeattle, WA206-763-7077

NORTHWESTPortland, OR503-232-3480

MIDWESTWest Chicago, IL800-848-5611

WEST COASTSacramento, CA800-421-9297

NORTHEASTAllentown, PA800-992-4428

SOUTHEASTLawrenceville, GA800-848-5611

★

★

★

★★

★

1349 West Bryn Mawr AvenueItasca, IL 60143800-BUILDEX

www.itwbuildex.com

SERVICECENTERLOCATIONS

Building Ideas That Work®

Teks®, TruGrip™ GT, Scots®, Maxiseal®, Dek-Cap™, Flashdek®, Tapcon®,Maxi-Set Tapcon®, Scots® Tapcon™, Condrive 500®, Condrive 1000®, Condrive2000®, E-Z Ancor®, E-Z Toggle™, E-Z EST™, Hi-Lo®, S-12®, Backer-On™,Rock-On™, Dec-King®, Dec-U-Drive®, Grid-Mate®, PB, Climaseal®, Spex™, Climacoat®,UltraShield®, Climashield™, White Ultrashield®, and Building Ideas That Work® areall registered trademarks of ITW Buildex.

Dektite® is a registered trademark of Deks Industries Pty Ltd.Phillips Square-driv® is a registered trademark of the Phillips Screw Company.Sikaflex® is a registered trademark of Chemco Company.Hypalon® is a registered trademark of the DuPont Company.Hardibacker® is a registered trademark owned by James Hardi Research Pty Ltd.

© 2002 Illinois Tool Works, Inc. Printed in U.S.A.

★

★

★

★★

★

Buildex 2003 cat

Documents

Transcript of Buildex 2003 cat