BUILDERS’ METALWORK - Amazon Web Services · BUILDERS’ METALWORK CI/SfB 21.9 Xt6. Page...

BUILDERS’METALWORK

CI/SfB 21.9 Xt6

Page Illustration Key

SPH Joist Hangers 4 - 5 1

Maxi Speedy Joist Hanger 6 - 7 2

Speedy Joist Hangers 8 - 9 3

Straps 10 4

Herringbone Joist Struts 11 5

Truss Clip 11 6

Wall Ties 12 7

Movement, Screw-in Starter and Cavity Ties 13

Safe Edge Frame Cramp 14 8

Screw-in Frame Ties 14

Security Mesh 14 9

Flat Wire Reinforcement 15

Exmet 15

Framing Anchors 16 10

Angle Plate 17 11

Angle Brackets 18 - 20 12

Timber Connectors 21 13

BAT-U-Nailplate 21

Splice Plates 22 14

Frame Cramp 23

Sole Plate Angles 23

Junction Clip 24

BAT Safeplate 24

Multi-purpose Fixing Band 24

Soffit Vent Mesh 25 15

Scrolled Hip Irons 26

Nails 26

Gallows Brackets 26

Wall Starter/UniStarter/Multi-Starter 27 - 29

BUILDERS’ METALWORKProduct Brochure

CONTENTS

8

10

15

911

12

13

14

2

3

4

5 6

7

1

EXPAMETSPH JOIST HANGERS

Design Features� Single-piece, non- welded construction.

� Wider masonry flange to increase loadings on masonry of

compressive strength 2.8N/mm2 and greater.

� Manufactured from 2mm thick pre-galvanised mild steel to

BS EN 10327 : 2004, DX51D + Z600.

� 75mm load bearing surfaces.

� All hangers 150mm deep and over are manufactured 10mm less to

allow for notching and regularisation of timber joists.

� Gusset nail holes are non coaxial.

� Standard available widths 38, 44, 47, 50, 63, 75, 100, 125, 150mm.

Installation RequirementsThe back face of hanger must be flush against the wall.

The timber joist should be square cut and butting to the back face of

the hanger (maximum permitted gap 6mm).

A minimum height of 675mm of set masonry must be in position

above the supporting flange before any load is applied.

Fixing: Nail to the joist through the nail holes in each side gusset with

BAT 3.75 x 30mm long square twisted sherardised nails.

It is recommended that joists are notched for the base of the hanger

to achieve a level surface for plasterboarding.

Type ‘R’ and ‘ST’ provide additional location and alignment during

construction.

HD Restraint Straps must be used with all types of SPH joist hangers

to provide lateral restraint.

How to Order/Specify BAT SPH Joist HangersTYPE ‘S’ –

Please state dimensions of joist

(a) depth

(b) width

e.g. SPHS22550

Minimum box quantity dependent on hanger size.

TYPES ‘R’ & ‘ST’ (made to order) –

Please state dimensions of joist

(a) depth

(b) width

(c) top flange (to suit wall width)

e.g. SPH22550R100

Quantity made to order

4

The BAT S.P.H. Joist Hanger is a single piece timber to

masonry hanger for building into the inner leaf of external

cavity walls and internal walls.

Straddle Type ‘ST’

(‘ST’ Type is two Standard Joist Hangers joined together with Jointing Plate).

Return Type ‘R’

(‘R’ Type is a Standard type ‘S’ with Return Plate added).

75mm

Standard Type ‘S’

Both the ‘R’ and ‘ST’ Type enables the hangers to be positioned accuratelywhilst the masonry is built above.

5

38 to 50 63 to 75 89 to 150Joist Widths (mm)Nominal Joist S.P.H. Hanger

Depth (mm) Depth (mm)

100 100 3.08 2.86 *125 125 3.21 2.98 *150 140 3.28 3.05 *175 165 3.40 3.07 *200 190 3.52 3.29 *225 215 3.65 3.43 *250 240 3.65 3.43 *275 265 3.65 3.43 *

* not availableMasonr y Strength 2 .8 N/mm2



100 100 3.13 4.29 4.47125 125 3.55 4.65 4.47150 140 3.80 4.87 4.42175 165 4.22 5.22 4.36200 190 4.63 5.58 4.31225 215 5.05 5.94 4.25250 240 5.05 5.94 4.25275 265 5.05 5.94 4.25

Masonr y Strength 7 .0 N/mm2



100 100 2.67 2.77 *125 125 2.86 2.98 *150 140 3.05 3.19 *175 165 3.25 3.40 *200 190 3.44 3.61 *225 215 3.63 3.82 *250 240 3.63 3.82 *275 265 3.63 3.82 *




100 100 2.84 2.93 4.17125 125 3.06 3.18 4.17150 140 3.19 3.33 4.08175 165 3.41 3.57 3.99200 190 3.64 3.83 3.90225 215 3.87 3.87 3.81250 240 3.87 3.87 3.81275 265 3.87 3.87 3.81


EXPAMETSPH JOIST HANGERS

Safe Working Loads of the S.P.H. Joist Hanger used with various types of masonry

EXPAMETMAXI SPEEDY

6

Ø4.5

20

5560

6015

38 to 150mm 75

Type

500

*

Type

440

*

Type

560

*

Type

620

*

23

Ø 14

3540

23

38

44

14 .5

20

38 to 100mm

75

Ø 4.5

4035

Type

240

*

T ype

335

*

T ype

380

*

* For lengths see calculations in How to Order.

Bend Lines

Joist Width W

Type = Blank Length mm 240/335/380/440/500/560/620

38mm

225mm

201mmLeg Length

w

d

The Maxi Speedy is a heavy duty hanger for the support of

Timber to Timber or Timber to Masonry, Concrete, etc with

provision for Nailing or Bolting.

Design Features� Manufactured from 1.5mm thick pre-galvanised mild steel to

BS EN 10327 : 2004, DX51D + Z275.

� Available in 7 types: MS240; MS335; MS380; MS440; MS500;

MS560 & MS620.

� Nail hole diameter: 4.5mm Bolt hole diameter: 14mm

� Available widths: 38, 47, 50, 63, 75, 100mm (122 + 150 for MS500,

560 + 620 only

Installation RequirementsFixing: use BAT 3.75 x 30mm long square twisted sherardised nails.

M12 Bolts or Coach screws as specified by fixing manufacturer.

How to Order/Specify Maxi Speedy Joist Hangers

Steps to specify requirements:

1. Joist dimensions:

Double joist depth and add joist width, ie for joist 225 deep x 38mm

wide then:

225 (d) + 225 (d) + 38 (w) = 488mm.

2. The Maxi Speedy blank

length must be less than

total calculated in step 1,

therefore select MS44038

(not MS500 as the joist

hanger would stand

proud).

7

EXPAMETMAXI SPEEDY

Maxi Speedy Permissible Safe Working Loads (kN)

NAILS ONLY

3.75 x 30mm long square twisted sherardised

Type No. of Nails SWLInto Face kN.

240 12 3.9

335 18 5.9

380 20 6.5

500 32 10.5

560 38 11.2

620 44 13.0

BOLTS ONLY

M12 Bolts

Type No. of Bolts SWLInto Face kN.

240 2 3.6

335 4 6.9

380 6 10.1

500 6 10.1

560 6 10.1

620 8 13.0

COACH SCREWS

12mm ø x 63mm long (min). USING STARTER HOLES

Type No. of Coach SWLScrews Into Face kN.

240 2 3.0

335 4 5.9

380 6 8.6

500 6 8.6

560 6 8.6

620 8 11.1

MASONRY ANCHORS

Indicative loads: refer to fixings supplier for recommended loads

Bolt No. of Bolts SWL’s for Masonry Strengths ofSize Into Face

20N 15N 7N 3.5N 2.8N

12mm 2 7.2kN 5.4kN 2.5kN 1.2kN 1kN

12mm 4 14.4kN 10.5kN 5kN 2.5kN 2kN

12mm 6 21.0kN 15.5kN 7.5kN 3.7kN 3kN

EXPAMET SPEEDY JOIST HANGERS

8

Ø3.8mm

L

36mm

34mm

W

0.9mm

W = 38 : L = 70 W = 47 : L = 65 W = 50 : L = 64

Depth ≤ 100

W = 38 : L = 191 : X = 76

Depth ≤ 175

W = 44 : L = 188 : X = 73W = 47 : L = 186 : X = 71W = 50 : L = 185 : X = 70

X

Strap

22 HolesØ3.8mm

25mm

ShoeW

50mm

0.9mm

Side Gusset

44mm

L

Speedy Joist Hangers provide a quick and safe method of joist

trimming for light and medium duty joints.

� Speedy Minor (SM) –

Light duty applications. 100mm maximum joist depth to be

supported.

� Short Leg (SL) –

Medium duty applications. 175mm maximum joist depth to be

supported.

� Standard Leg (ST) & Long Leg (LLS) –

Medium duty applications. 225mm maximum joist depth to be

supported.

� Speedy Girder Truss Shoe (SGTS) –

Designed to offer a safe and economical method of connecting

trusses to girder units. It incorporates a specially extended bearing

surface of 85mm.

� Long Leg Speedy (LLS) –

Medium duty 225mm maximum joist depth. Suitable for

underslung joists (maximum 100mm drop).

� Girder/Girder Speedy –

For connection of girder trusses.

Design Features� Speedy Hangers

Manufactured from 0.9mm thick pre-galvanised mild steel to BS EN

10327 : 2004, DX51D + Z275.

Hole diameter: 3.8mm. LLS manufactured from 1.5mm thick

material

� Girder/Girder Speedy

Manufactured from 3mm thick galvanised mild steel to BS EN 1461.

Hole diameter: 22mm.

Installation RequirementsFixing: use BAT 3.75 x 30mm long square twisted sherardised nails

through all available nail holes.

For ease of use the legs are adjustable by hand to suit all

varying depths of supporting timber.

The depth of the supporting timber must not be less than the

hanger side gusset height.

SHORT-LEG/STANDARD-LEG SPEEDY SPEEDY MINOR

SPEEDY MINOR

Speedy Minor SM 38, 47, 50 1.6

Speedy Short Leg SL 38, 44, 47, 50 3.4

Standard Leg ST 38, 44, 47, 50, 63, 75, 100 4.3

Girder Truss Shoe SGTS 38, 44, 47, 50, 75 7.1

Long Leg LLS 38, 47, 50, 63, 75, 100 6.7

Girder/Girder Speedy GGTS 80, 105, 120, 155 See BS 5268 : Pt2

Type Joist Width Safe Working(mm) Load (kN)

How to Order/SpecifyPlease quote type reference and joist width to be carried.

SHORT LEG SPEEDY

W = 38 L = 281 X = 116W = 44 L = 278 X = 113W = 47 L = 276 X = 111W = 50 L = 275 X = 110W = 63 L = 268 X = 103W = 75 L = 262 X = 97W = 100 L = 250 X = 85

Strap

29 HolesØ3.8mm

34.5mm

Shoe

25mm

Side Gusset

W

0.9mm

50mm

L

X

Depth ≤ 225

9

EXPAMET SPEEDY JOIST HANGERS

GIRDER SPEEDY

STANDARD LEG SPEEDY (W = 38, 44, 47, 50, 63, 75, 100)

35mm

50mm

113mm107mm

W = 38 L = 396 X = 137W = 47 L = 392 X = 134W = 50 L = 390 X = 131W = 63 L = 383 X = 124W = 75 L = 377 X = 118W = 100 L = 365 X = 106

W

L

X

Depth ≤ 225

LONG LEG SPEEDY (W = 38, 47, 50, 63, 75, 100)

34 HolesØ3.8m m

25m m

Shoe85m m

1.2m m

Side Gusset20m m

25m

m

W = 38 L = 271 X = 115 W = 44 L = 268 X = 112W = 47 L = 267 X = 110W = 50 L = 265 X = 109W = 75 L = 252 X = 96

44m m

Strap

W

L

X

SPEEDY GIRDER TRUSS SHOE (W = 38, 44, 47, 50, 75)

3 HolesØ22mm

120mm

W = 80 L = 550 X = 490W = 105 L = 550 X = 490W = 120 L = 550 X = 490W = 155 L = 550 X = 490

W

X

6 HolesØ4mm

L

GIRDER/GIRDER SPEEDY (W = 80, 105, 120, 155)

36 nail holes

Nails:3.75 x 30mmlong squaretwistedsherardised

EXPAMET STRAPS

50

27.5

33

25

12. 5 12. 5

100

250

400

BAT straps are manufactured in two types. The Heavy Duty to

provide horizontal restraint and Standard to provide vertical

restraint against wind pressure and uplift forces.

Design Features� The straps are manufactured from pre-galvanised steel strips

with zinc coated edges to BS EN 10327 : 2004, DX51D + Z275

or stainless steel to BS EN 10088-1 : 1995 : 1.4301.

� Nominal Dimensions

Heavy Duty - 27.5 x 5.0mm

Standard - 27.5 x 2.5mm

� Hole diameters are 6mm and they are holed at 12.5mm

grouped in threes, diagonally across the width of the strap.

STANDARD STRAP HEAVY DUTY STRAP

Dimensions

Anchorage of gable end to roofstructure.

Fixing to wall plate and wall with onebend.

Floor level straps notched into paralleljoists. Note: Gaps between masonryand adjacent joists must be packed.

Floor level straps. 150 x 650mm longonce bent and once twisted fixed toperpendicular joists.

Note: Turn down of the strap mustbe in contact with the masonry.

Installation RequirementsThe installation of restraint straps must comply with the current

Building Regulations, British Standards BS 5628 : Part 1 and Part 3

and BS 8103 : Part 1, as well as NHBC recommendations.

When straps are being fixed across joists or trussed rafters which are

parallel with the wall, and where there is a gap between the wall and

the first joist or truss, the gap must be packed. Noggins must be

provided between each joist or truss.

Fixing for Heavy Duty and Standard Straps: use either No 12 x 50mm

wood screws or 4.00 dia x 75mm corrosion resistant nails.

For stainless steel straps, stainless steel fixings must be used.

OrderingWhen ordering quote the overall length and distance of bend/twist from

END of strap. eg. overall length, bent at 100mm, bent at 250mm, twisted at

400mm. E.g. HD1000B100, ST1000T400

If in doubt, provide sketch.

10

Illustration shows the standardclockwise rotation to strap.

Anticlockwise is also possible.

The Bat Truss Clip eliminates the disadvantages of skew

nailing trussed rafters to timber wall plates; damaged

connector plates; split rafters or wall plates.

Design Features� Manufactured from 0.9mm thick pre-galvanised mild steel to BS EN

10327 : 2004, DX51D + Z275.

� Hole diameter: 4mm Height: 117mm

� Available in 2 sizes:

� Other thicknesses of trussed rafters may be fixed using pairs of

BAT Framing Anchors, type MFAAL and MFAAR.

Ref. Width Qty/Box Safe Working Load Uplift (kN)

TC38 38mm thick truss 200 1.3

TC50 50mm thick truss 200 0.7

EXPAMET HERRINGBONEJOIST STRUTS

TRUSS CLIP

Herringbone Joist Struts provide stability to floor joists.

Expamet Herringbone Joist Struts significantly reduce labour

content in fixing strutting on site.

Design Features� Manufactured from 1mm thick pre-galvanised mild steel to BS EN

10327:2004 : DX51D + Z275.

� Suitable for joist widths between 38mm and 63mm, and joist

depths between 150mm and 225mm.


Installation RequirementsJoist Span – 2.5m to 4.5m 1 Row at mid span

greater than 4.5m 2 Rows at 1/3 span positions

Fixing: use BAT 3.75 x 30mm long square twisted sherardised nails.

Ref. Joist Centres Length Qty/Box

HJS400 400mm 480mm 50

HJS450 450mm 523mm 50

HJS600 600mm 660mm 50

Fixing Detail

Single 3.75 x 30mm Sheradised Square Twisted Nail

When fixing the second strut a 6mm (approx) gap should be kept between the struts.

4 Holes (both ends)

57mm

30m

m

Length

12 Holes @ 4mmØ

38 to 50

117.5

25.5 to 31

0.9

114.3

28.5


All nail holes must be filled.

The timber wall plate must be securely held down onto the supporting

masonry.

11

STAINLESS STEELWALL TIES

12

PT200#50PT200PT225#50PT225

MPT200#50MPT200MPT225#50MPT225MPT250

PT1-200PT1-225PT1-250PT1-275PT1-300

7575100100

7575100100125

75100125150150

5 x 502505 x 50250

5 x 502505 x 50250250

250250250250250

Type 4Type 4Type 4Type 4

Type 2Type 2Type 2Type 2Type 2

Type 1Type 1Type 1Type 1Type 1

200mm Housing Wall Tie200mm Housing Wall Tie225mm Housing Wall Tie225mm Housing Wall Tie

200mm General Purpose Wall Tie200mm General Purpose Wall Tie225mm General Purpose Wall Tie225mm General Purpose Wall Tie250mm General Purpose Wall Tie

200mm Heavy Duty Wall Tie225mm Heavy Duty Wall Tie250mm Heavy Duty Wall Tie275mm Heavy Duty Wall Tie300mm Heavy Duty Wall Tie

DT200DT225DT250DT300

SSCD

PTJ4115PTJ4135PTJ4165

SSFSSSFS75SSFS100

75100125150

5075100

5075100

250250250250

250

250250250

250250250

Type 2Type 2Type 3Type 3

Type 4Type 4Type 4

Type 6Type 6Type 6

200mm Double Triangle Wall Tie225mm Double Triangle Wall Tie250mm Double Triangle Wall Tie300mm Double Triangle Wall Tie

Insulation Retaining Disc. Fits all Ties.

Thin Joint Masonry TieThin Joint Masonry TieThin Joint Masonry Tie

Timber Frame Tie including nailTimber Frame Tie including nailTimber Frame Tie including nail

Type Reference NominalCavityWidth (mm)

Quantity Classification Description

Domestic up to 2 storey, 10m high. Part E (Separating Walls). Type A compliant.

PART EParty Walls

TYPE

A

PART EExternal Walls

TYPE

B

Domestic up to2 storey, 10m high. Maximum block density 550 kg/m3.

Allow for maximum heightdisplacement of 24mm.

Domestic and smallcommercial up to 15m high.


TYPE

B

Most masonry cavity walls.

BS EN 845-1 Wall Ties

Thin Joint Masonry Ties

Timber Frame Tie

Power-Tie Wall Ties are manufactured to comply with BS EN 845 –1 thespecification for ancillary components for masonry, Part 1: ties, tensionstraps, hangers and brackets.

DD140 and EN845-1 requires specific design characteristics allowing thedesigner to specify the correct type of Wall Tie for each situation.

Wall Ties should be installed in accordance with BS 5628-3, the code ofpractise for the use of masonry, Part 3: materials and components, designand workmanship.

Stainless steel type 1.4301 to BS EN 10088-1.

For our full range of cavity wall ties and ancillary fixings please seewww.expamet.co.uk/expamet-powertie


TYPE

B

STAINLESS STEELMOVEMENT TIES

13

STAINLESS STEELSCREW-IN STARTERAND CAVITY TIES

Movement joints are necessary in masonry wall panels to cater for the naturalmovement of buildings. Tensile and compressive forces can develop that lead to cracking and bowing of walls.

BS5628-3 details the provision of movement joints in clay, calcium silicate, concrete and stone masonry.

Power-Tie Movement Ties allow expansion and contraction at movement jointswhilst providing shear resistance between adjacent panels and supports.

Placing the sleeve on the plain end of the movement tie with 10mm clearance,debonds the tie from the mortar joint, permitting longitudinal movement.

SMT200SMT225SMT250

BMT 100BMT 150BMT 200

L:200L:225L:250

L:100 / H:50L:150 / H:50L:200 / H:50

100100100

100100100

Straight Movement Tiesare built into the corresponding bed jointsof adjacent panels.

Bent Movement Ties aremechanically fixed toadjacent supports.Slotted end providesvertical adjustment.

L

L

H

Type Reference Size (mm) Quantity Description

Straight Movement Tie with debonding sleeve.

Bent Movement Tie with debonding sleeve.

SST130#10SST130

SCT 150SCT 180SCT 200SCT 225

130130

150180200225

10100

100100100100

Screw-in Starter TieScrew-in Starter Tie

Screw-in Cavity Tie with V DripScrew-in Cavity Tie with V DripScrew-in Cavity Tie with V DripScrew-in Cavity Tie with V Drip

Type Reference Length (mm) Quantity Description

SST SCT

Quick and easymethod to tie newwalls to existingwalls.

Screw-in Starter andCavity Ties are madefrom austeniticstainless steel to BS EN 10088-3.

Supplied withmasonry plug.

Nominal cavity widthfor SCT: 50 - 100mm.

EXPAMET SAFE EDGEFRAME CRAMPS ANDSCREW-IN FRAME TIES

14

BAT Safe Edge Frame Cramps provide positive location of

window and door frames to inner leaf of masonry.

Manufactured from pre-galvanised steel strip with zinc

coated edges to BS EN 10327:2004 : DX51D + Z275.

Fixing: use 2 No 4.5mm nails or No. 8 screws, galvanised or

sherardised.

A cost effective way of securing buildings or internal spaces by

sandwiching a layer of steel mesh into the walls and ceilings

during construction.

Available in a range of gauges this high quality security mesh

is suitable for internal walls, ceilings, partitions and external

brickwork. It can also be provided in galvanised steel, where

damp conditions are expected.

See our full range of Expanded metal and lath at

www.expamet.co.uk

2

6 Dia Holes

502610

8

19

100 / 150 / 200

50Ref. Width Length Upstand Qty/Box

SEFC150 19mm 100mm 50mm 125

SEFC200 19mm 150mm 50mm 125

SEFC250 19mm 200mm 50mm 125

Ref. Size (mm) Qty per boxMaterial

SIFT130RT

SIFT130#10

130

130

100

10 bags of 10

Stainless Steel

Stainless Steel

Screw-in Frame Ties secure timber window and door frames

to inner leaf of masonry.

SIFT 150 100Bright Zinc Plated Steel

SIFTSIFT130

50-73HFG50-73HF

50-89HRG50-89HR

50-76MFG50-76MF

(Above shown at approx 50% actual size)

EXPAMET SECURITY MESH

Description

Security Mesh - FlattenedSecurity Mesh - RaisedSecurity Mesh - Flattened

Security Mesh - FlattenedSecurity Mesh - RaisedSecurity Mesh - Flattened

MeshLW

42.950.8*43.4

42.950.8*43.4

MeshSW

14.222.6*18.0

14.222.6*18.0

StrandThickness

2.73.01.1

2.73.01.1

StrandWidth

4.63.12.3

4.63.12.3

WeightKg/m2

8.596.521.85

8.596.521.85

Sheet Size

2440 x 12202440 x 12201250 x 2500

2440 x 12202440 x 12201250 x 2500

Material

Galvanised Steel to BS EN ISO 1461Galvanised Steel to BS EN ISO 1461Galvanised Steel to BS EN ISO 1461

Hot Rolled Mild SteelHot Rolled Mild SteelCold Rolled Mild Steel

Ref.

50-73HFG50-89HRG50-76MFG

50-73HF50-89HR50-76MF

* Mesh pitch size

FLAT WIREREINFORCEMENTFor structural applications

EXMET REINFORCEMENTFor non-structural applications

15

Ref Material Coil Size Wall Quantity Thickness Width Width(mm) (mm) (mm)

76820 0.3 65 100 5

76920 0.3 115 140 5

77020 0.3 175 225 1

77120 0.3 225 265 1

Stainless steel Exmet is manufactured from austenitic

stainless steel 1.4301 to BS EN 10088-1. Coil length 20m.

Expanded steel mesh with no joints or interweaving to fail

under stress.

Overlap ends 75mm.

Power-Tie Flat Wire LadderReinforcement is made fromaustenitic stainless steel to 1.4301 :BS EN 10088-3.

Ladder length 2700mm.

Conforms to BS 5628-2.500N/mm2 minimum tensile strength.

Special designs are available on request for corners and T-shapes.

Reference Type Main Wire Equivalent Ladder Wall Width QtyHeight (mm) Round Wire Width (mm) (mm)

Diameter (mm)

SBSF3060 Single Leaf 2.8 3 60 100 20SBSF30100 Single Leaf 2.8 3 100 140/150 20SBSF30150 Single Leaf 2.8 3 150 190/200 20SBSF30175 Single Leaf 2.8 3 175 215 20

SBSF3560 Single Leaf 2.9 3.5 60 100 20SBSF35100 Single Leaf 2.9 3.5 100 140/150 20SBSF35150 Single Leaf 2.9 3.5 150 190/200 20SBSF35175 Single Leaf 2.9 3.5 175 215 20

SBSF4060 Single Leaf 3 4 60 100 20SBSF40100 Single Leaf 3 4 100 140/150 20SBSF40150 Single Leaf 3 4 150 190/200 20SBSF40175 Single Leaf 3 4 175 215 20

SBSF4560 Single Leaf 3 4.5 60 100 20SBSF45100 Single Leaf 3 4.5 100 140/150 20SBSF45150 Single Leaf 3 4.5 150 190/200 20SBSF45175 Single Leaf 3 4.5 175 215 20

SBSF5060 Single Leaf 3 5.0 60 100 20SBSF50100 Single Leaf 3 5.0 100 140/150 20SBSF50150 Single Leaf 3 5.0 150 190/200 20SBSF50175 Single Leaf 3 5.0 175 215 20

Overlap ends 225mm.

8

127

60

40

15

2632

33. 5

43

60

40

15

EXPAMETFRAMING ANCHORS

BAT Multi-Grip Framing Anchors offer the most effective and

economical method of providing strong, mechanical joints for

framing of timbers

Five types available: AL, AR, BL, BR and C.

MFAAL & MFAAR: for anchoring rafters and trusses to wall plate.

MFABL & MFABR: for anchoring headers to studs, beams to posts and

studs to plates.

MFAC: for right or left handed use – for anchoring joists to

beams, stringers to headers and hip joints.

Design Features� Manufactured from 1mm thick pre-galvanised mild steel

to BS EN 10327 : 2004, DX51D + Z275.

Overall height: 127mm

Width: 34mm

Hole dimension: 4mm

200 no. per box

Installation RequirementsFraming anchors must always be used in pairs to minimise

eccentric loading.

Recommended fixing: BAT 3.75 x 30mm long square twisted

sherardised nails.

Note: Use all available timber facing holes.

16

Safe Working Loads:

Types A & B:longitudinal capacity1.3kN/pair

lateral capacity 1.1kN/pair

Type C:longitudinal capacity3.7kN/pair

Longitudinal Loads

Lateral L

oads

108

127

60

40

15

2632

2028

55

35

10

112632

10

2820

8

127

60

40

15

2632

33. 5

55

35

10

43

2926

18

2926

18

TYPE MFAAL

TYPE MFABL

TYPE MFAC

MFAAL(left handed)

MFABL(left handed)

MFAAR(right handed)

MFABR(right handed)

MFAC

EXPAMETANGLE PLATE

BAT Angle Plates are used as a safe and economical method of

connecting joists to purlins.

Design Features� Manufactured from 2mm thick hot dipped pre-galvanised

mild steel to BS EN 10327 : 2004, DX51D + Z275.

� Safe Working Loads: 1 pair = 3.5kN

2 pairs = 7.5kN

Ref: AP30030 300mm x 30mm x 30mm 50 per bag


Use all timber facing nail holes.

Minimum timber depth of 150mm.

Ensure the timbers project a minimum of 50mm beyond the Angle

Plates.

17

Steel Beam

Timber packer in beam (bolted) .

150mmminimum

60

38

AB

18.5

5.5 1 2 25 5.512

12

14

14

11x30

5.5 1 2 5.51225

14 14

11

9

6

16

2

7Ø 7Ø

11Ø

EXPAMETANGLE BRACKETS

18

BAT Angle Brackets are designed for

multi-purpose fixing applications and can be

used as replacement cleats, nailed or bolted.

Design Features� Manufactured from hot dipped pre-galvanised

mild steel to BS EN 10327 : 2004, DX51D + Z275.

� Light Duty: AB604060

2mm thick

� Heavy Duty: HD9090; HD15090; HD150150

2mm thick, ribbed

Installation RequirementsAngle Brackets may be used for timber/timber,

timber/steel and timber/masonry connections.

May be fixed with nails, bolts or coach screws.

Must be used in pairs.

Nailed Safe Working Loads kN (per pair)

Type Uplift Shear

AB604060 1.2 1.8

HD9090 1.6 3.6

HD15090 1.4 4.6HD150150

BS 5268 Pt 2 Long term loads

Nails 3.75 x 30mm long square twisted sherardised

LIGHT DUTYRef: AB60406060mm x 40mm x 60mm 12 holes @ 4.5mm ø100 no. per box

VIEW ON B

VIEW ON A

87 2

87A

B

13

42

17

27

59

59

10

7

10

17. 5 17. 5 35 10

22. 5 32 17

11x3059

Stiffening Rib

9Ø

9Ø

9Ø

9Ø

11Ø

HEAVY DUTYRef: HD909087mm x 87mm x 59mm 16 holes @ 4mm ø50 no. per box

VIEW ON B

VIEW ON A

Uplift

Shear

D

27

63

2222. 5

C

290

150

90 (TYP)

11x30

51

42

17

63

1030

3017.5

17.535

10

10 7

63

32 17

Stiffening Rib

11x30

10 17.5 17.5 35 10

7

10

Ø 9

11Ø

Ø 9

Ø 9

Ø 9


19

F

11x30

31

63

24

53

30

Ø 9

63

11 25 25 30 30 29

6

10

11x30

23 54 30

2

150

150

E

Stiffening Rib

26

10

10

Ø 9

Ø 9

Ø 9

Ø 9

Ø 9



VIEW ON C

VIEW ON D

VIEW ON E

VIEW ON F


20

Light Duty Angle Brackets

Ref Size (mm) A x B x C Qty

AB303015 30 x 30 x 15 100

AB404040 40 x 40 x 40 100

AB505035 50 x 50 x 35 100

AB604060 60 x 40 x 60 100

AB804042 80 x 40 x 42 50

AB808018 80 x 80 x 18 50

AB906059 90 x 60 x 59 50

AB909060 90 x 90 x 60 50

AB1006060 100 x 60 x 60 50

AB12512542 125 x 125 x 42 50

AB1509059 150 x 90 x 59 50

AB15015063 150 x 150 x 63 50

Adjustable Angle Brackets


AAB1403540 140 x 35 x 40 50

AAB806520 80 x 65 x 20 20

Nail Plate Brackets


NPA767676 76 x 76 x 76 50

NPA575751 57 x 57 x 51 50

Angle Plates


AP2103030 30 x 30 x 210 50

AP3003030 30 x 30 x 300 50

T & L Jointing Plate

Ref Size (mm) A1 x A2 x B Qty

T1408030 140 x 80 x 30 20

L12012020 120 x 120 x 20 20

Flat Jointing Plate

Ref Size (mm) A x B Qty

JP17559 175 x 59 50

JP46250 250 x 46 50

JP63300 300 x 63 50

C

A

B

C

A

B

CA

B

C

A

B

B

A1

A2B

B

A1

BA

A2

B

EXPAMETTIMBER CONNECTORS

21

SHEAR PLATE 102 SHEAR PLATE 67

Shear PlateManufactured in 2 sizes: SPT67 (B2) x 150 per box and SPT102 (B3) x

50 per box

Designed for use with M20 bolt.

Material Specification:

67mm – Manufactured from galvanised hot rolled steel to

BS EN 10025.

100mm – Galvanised cast iron to BS EN 1562.

Square Plate WashersManufactured in 1 size: SPW50 (50mm square). To suit 12mm bolt.

250 per box.

Bolts are not supplied with timber connectors.

Tooth Plate (Round)Manufactured in 3 sizes:

50, 63 and 75 diameter. 200, 150

and 100 per box respectively.

Available in both single and

double sided, eg. ref. TCSS (C6);

TCDS (C7) etc.

Suitable for M12 bolt.


Manufactured from pre-galvanised

steel to BS EN 10327 : 2004

DX51D + Z275.

Split RingManufactured in 2 sizes:

SRTC64 (A3) x 100 per box and

SRTC102 (A3) x 100 per box

Designed for use with M12

and M20 bolts respectively.

Double bevelled.


Manufactured from galvanised

hot rolled steel to BSEN10025.

BAT Timber Connectors are made in accordance with the

requirements of BS EN 912 : 2000 ‘specification for connectors

for timber’. Safe working loads, end distances and spacing are

all set out in BS 5268 Part 2.

Application Tools For use with timber connectors.Available to special order.

REF TYPE SIZE mm

SRGT/64 Split Ring Grooving &Dapping Tool 64mm split ring

SRGT/102 Split Ring Grooving &Dapping Tool 102mm split ring

DT/67 Shear Plate Grooving &Dapping Tool 67mm shear plate

DT/102 Shear Plate Grooving &Dapping Tool 102mm plates

BAT-U-NAIL PLATE

Ø3. 5

50 .8

12.7

DIRECTION OF STIFTENING RIBS

19 4.75

±1.

5

76

114

152

51100

152203

254

305

354

BAT-U-Nail is a plate system which enables timber structures

to be made on site or in the builders workshop, since it is

nailed by hand.

Design Features� Manufactured from 0.9mm pre-galvanised mild steel to

BS EN 10327: 2004 : DX51D + Z275.

� Widths: 76, 114 and 152mm

� Lengths: 51, 100, 152, 203, 254, 305 and 354mm.

� Various quantities per box. Ref. eg. BP7651.

Installation RequirementsBAT-U-Nail plates are to be fixed on both sides of the timber.

Fixing: use BAT 3.75 x 30mm long square twisted sherardised nails –

Loading in the direction of the plate stiffening ribs.

345 N/nail (parallel to timber grain).

145 N/nail (perpendicular to timber grain).

Plate compression value 40 N/mm width of plate. To calculate

capacity of connections, the lesser of anchorage, plate compression

and tension should be taken.

Fix in accordance with BS 5268 : Part 2.

EXPAMETSPLICE PLATES

22

Suitable for butt jointing timbers of similar cross section.

Design Features� Manufactured from 1.2mm thick pre-galvanised mild steel to

BS EN 10326 : 2004 S280GD + Z275.

� Available in 3 types:

L61 61 x 400mm long up to 150mm deep joist



� 8 sets of 4 per box (32 pieces) including nails.

Installation RequirementsJoint consists of 4 pieces.

All nail holes must be used.

Minimum timber thickness 50mm.

Can be used for:

� Replacement of rotten and decayed floor joist ends.

� Replacement of fire damaged structural timbers.

� Making good localised damage or decay in structural timber work.

61mm

18 mm

L61

400mm

80mm

18 mm

L80560mm

98mm

18 mm

L98

560mm

Timber Joist

Existing Joist

Joist Splice Plate Splice Plate Resistance Shear Approx. NailsDepth Code Size (mm) Moment (kNm) Capacity (kN) per plate

125 L61 18 x 61 x 400 1.5 13 27150

175 L80 18 x 80 x 560 1.5 13 52200

225 L98 18 x 98 x 560 1.5 13 65250

EXPAMETFRAME CRAMP

23

SOLE PLATE ANGLES

BAT Sole Plate Angles positively locate timber sole plates to

concrete floor slabs using masonry fixings as required, without

penetrating the dpc.

Design Features� Manufactured from 0.9mm thick hot dipped galvanised

mild steel to BS EN 10327 : 2004 DX51D + Z275.


Installation RequirementsBAT Sole Plate Angles may be fixed on the inside of the sole plate or

alternatively fixed under the sole plate with the upstand on the

outside of the sole plate.

Fixing: use 3.75 x 50mm minimum length nails/masonry nails.

To provide positive location and support of window from

timber framing to resist wind and incidental loadings.

Design Features� Manufactured from 0.9mm thick hot dipped galvanised

mild steel to BS EN 10327 : 2004 DX51D + Z275.


Installation RequirementsFixing: use BAT 3.75 x 30mm long square twisted sheradised nails.

Ref. Width Length Upstand Qty/Box

FC1 76mm 202mm - 100

FC2 76mm 212mm 40mm 100

PLAN VIEW

SECTION VIEW

Ref. Width Length Upstand Qty/Box

SPA112 76mm 112mm 40mm 100

SPA162 76mm 162mm 40mm 100

EXPAMETJUNCTION CLIP

24

MULTI-PURPOSEFIXING BAND

Can be used instead of noggins, at wall junctions and atcontact points between ceiling and walls when fitted at300mm centres.

Design Features� Manufactured from 1mm hot dipped galvanised mild

steel to BS EN 10327 : 2004 : DX51D + Z275.

Ref: JC1 250 per box.

Installation RequirementsFixing: use BAT 3.75 x 30mm long square twisted sherardised nails or

ordinary plasterboard nails.

For protection of plumbing and electrical wiring againstrandom nailing into studs.

Design Features� Manufactured from 1mm hot dipped galvanised

mild steel to BS EN 10327 : 2004 : DX51D + Z275.

Ref: SAF1 90 x 54mm 200 per box

Installation RequirementsUse wherever services occur within 75mm of face of plasterboard or

100mm of surface of floor deck. Fixing: Tap in with hammer.

Expamet Fixing Band is an easy-to-use coil strip designed forall types of light fixing applications.

Design Features� Manufactured from hot dipped galvanised mild steel to

BS EN 10327 : 2004 DX51D + Z275.

� Available in 3 sizes

Installation RequirementsFixing: use BAT 3.75 x 30mm long square twisted sherardised nails,

screws or bolts. Not to be used below ground.

BAT SAFEPLATE

Pipe fixing, Generalsupport & Duct work

58Pitch

17

29

12

413.8 Dia6.25 Dia

4

Clamping, Bracing &Restraining

Timber repair...Fencing, Garden Sheds etc

Ref. Width Thickness Length

MFBA 20mm 0.9mm 10 metre coil

MFBB 20mm 0.7mm 10 metre coil

MFBA/20 20mm 0.9mm 20 metre coil

EXPAMETSOFFIT VENT MESH

25

The provision of eaves vents to limit condensation risk is arequirement of the Building Regulations.

Expamet expanded stainless steel is used over the vents toexclude birds and insects. This mesh is an economical materialfor the purpose. It is readily adaptable to various eavesdetails, is light in weight and easy to handle on site. Coils of mesh in convenient dispensers make site work easier andavoid wastage.

Design Features� Manufactured from stainless steel to

BS EN 10088-1 : 2005 : 1.4404.

� Approx. weight 0.370kg/m2.Ref: SVM1 30m x 75mm.

Installation RequirementsStainless steel nails or staples should be used for fixing the eaves vent mesh.

Closed area 34%. The vent gap should be increased to 15mm or 38mm to compensate.

Mesh fixed to rear of fascia board

Mesh bent to shape required

Mesh held in position by soffit board

Soffit mesh fixed along the back of fascia board

Predrilled ventilation hole

Mesh fixed to rearof fascia priorto fixing fasci

Mesh bent to shape required and compressed to fill gap on fixing of fascia board

Mesh is fixed to rafter ends, bent and returned to underside

Fascia and soffit boards are then fixed

75 x 50mm fixing block

Soffit board rebated to fascia board

Mesh fixed to soffit board prior to fixing of soffit board

Mesh bent to shape required

Examples of Applications

EXPAMETSCROLLED HIP IRONS

26

NAILS

GALLOWS BRACKETS

Designed to provide decorative restraint when bedding hip tiles.

Ref Material Length x Width x Thick Height

HIP2003 Galvanised 200mm x 25mm x 3mm 100mm




Stainless Steel Annular Ring NailsSSRN 3.35 x 50mm 1000 per box

Sherardised NailsSN32 BAT 3.75 x 30mm twisted 1000 per box

SN321 BAT 3.75 x 30mm twisted 10000 per box

The Gallows Bracket provides a method of supporting

otherwise unsupported brickwork.

Manufactured from 50 x 50 x 5 angle, red oxide finish.

Two sizes are available (supplied in pairs).

To suit M12 Masonry Anchors - not supplied.

Red Oxide:

MH375375 375mm high x 375mm deep (projection from wall)

MH490375 490mm high x 375mm deep (projection from wall)

Height

Height

Depth

LengthWidth

Thick

EXPAMET WALL STARTERS, UNISTARTERS AND MULTI-STARTERS

27

The quick, easy-to-fix way to tie-in new walls to existing walls

without cutting out brickwork. Suitable for walls of up to three

storeys high, ie up to 8m maximum.

Wall Starters

Ref Description Type Wall Thickness

WS060 Stainless Steel Single Flange Integral Tie 60 - 75mm




WGC060 Plastisol Coated Galv Single Flange Integral Tie 60 - 75mm



WGC 185 Plastisol Coated Galv Single Flange Integral Tie 190 - 260mm

UniStarters

UWSS Stainless Steel No Flange Integral Tie Up to 250mm

UWGC Plastisol Coated Galv No Flange Integral Tie Up to 250mm

Multi-Starters

MSSS Stainless Steel No Flange Turn-n-slide Ties Up to 250mm

MSGC Plastisol Coated Galv No Flange Turn-n-slide Ties Up to 250mm

MSGFIX Plastisol Coated Galv Extra Fixing Pack

MSGFIX Stainless Steel Extra Fixing Pack

Contains 10 ties, 5 screws, plugs & washers

Stainless SteelRef. WS060

Plastisol CoatedGalvanised SteelRef. WGC060

For lightweightblock walls 60to 75mm thick.



For brick or blockwalls 100to 115mm thick.







Wall StartersIndividual products designed for specific widths of

new walls

There are four ‘flanged’ products in the Expamet Wall Starter range,

each designed for a specific wall widths, from 60mm to 260mm thick.

UniStartersThe universal wallstarter for any wall

The flat flange-free design of Expamet UniStarters means they can

be used to construct any wall between 75mm and 250mm thick –

one product, multiple applications.

Stainless SteelRef. UWSS

Plastisol CoatedGalvanised Steel Ref. UWGCAll Wall Starters, Unistarters and Multistarters are supplied with the necessary fixings.

28

EXPAMET WALLSTARTERS & UNISTARTERSFIXING INSTRUCTIONS

675

fixingpoints

drill, plug and fixusing fixingssupplied

The distance between the flangessets the cavity width.

Tie-line

Tie-line

Tie-line

Tie-line

Dimension to suit centralisingof UniStarters in leaves of new wall.

25

eitherholemay beused

eitherholemay beused

slot flat slot

joining adjacent Wall Starters, and UniStarters

450

675

450

WALL STARTERSCAVITY WALLS – Brick & Block

The left hand Wall Starter is fixed with its ties extending upwards ready

for bending down into the mortar courses. The right hand Wall Starter is

inverted and fixed with the ties extending downwards.

They must then be bent upwards ready for setting into the mortar course

as the wall is built.

UNISTARTERSCAVITY WALLS – Brick & Block

UniStarters are fixed with their ties extending upwards ready for bending

down into the mortar courses. The right hand UniStarter is higher to allow

the tie to bed into the first blockwork mortar course.

Wall Starter & UniStarter Installation

� Suitable for both metric and imperial brick/block sizes.

� Integral ties are designed to tie into every (225mm deep) block

course or every third course of (75mm deep) bricks.

� Each pack contains two 1175mm lengths. Slotted holes at each end

allow easy connection of one length to the next.

� Full fixing instructions and all necessary coach screws, washers

and plugs are provided. Only 5 fixings are needed for the two

lengths (Type 120 and 185 Wall Starters are supplied with

10 fixings). The only tools you need are: spirit level, drill (with

10mm masonry bit) and 10mm spanner.

� Miscoursing of up to 50mm can be solved by simply bending

integral ties to suit. This will reduce the length of ‘built-in’ tie, but

it still meets relevant test criteria.

� All products are designed to allow up to 10mm vertical movement.

� If the upper end of the product extends past the top line of your

wall, use tin-snips or a hacksaw to cut off the excess and attach

using the remaining top fixing hole.

� Align the centreline of the UniStarter with the centre of the new

wall. Align the flanged edge of the Wall Starter to the front or back

of the new wall.

� For cavity walls, each leaf will require a separate starter.

� All external walls require a 10mm wide weather seal to be fitted

between the product and the existing wall or applied to the

raked-out vertical joint.

� In exposed locations (or to meet Local Authority specifications),

a vertical DPC should be cut into the existing wall prior to fixing

the product.

EXPAMET MULTI-STARTERS

29

Multi-StartersFeaturing a ‘turn-n-slide tie’ to accommodate all sizes of

brick/block.

The Multi-Starter is suitable for all wall widths from 60mm-250mm.

Installation� The turn-n-slide ties enable the starter to be tied into any course

the builder wishes, ideally every (225mm deep) block course or

every third course of (75mm deep) bricks.

� Each pack contains two 1165mm lengths. Slots at each end allow

easy connection of one length to the next.

� For more information see Wall Starter & UniStarter installation

details on previous page.Stainless SteelRef. MSSS

Plastisol Coated Galvanised Steel Ref. MSGC

Fixing Details

Joining adjacentMulti-Starters

Fixing points

675

450

675

450

Drill, plug and fix using fixingssupplied

Insert Turn (anti-clockwise)

Slide

For Masonry MovementJoint applications – use Expamet MovementTies.

PLUMBEnsure existing wall is sound and clean.Locate the starter above the DPC.Plumb the section and mark positionsof the fixing holes.

DRILLDrill and plug the existing wall, takingcare to avoid mortar joints.

FIXLightly screw the first length to theexisting wall over weatherseal if required,then plumb, mark and drill out the nextstarter. Make sure that the slot at the endof one length always lies on top of theslot of the adjacent length. Tighten allscrews when all required lengths arein position.

BUILDLay bricks or blocks, be sure to bed themwith mortar against the starter.Multi-Starter: Turn-n-slide ties into themortar as you build.Wall Starters and UniStarters: Bend tiesinto the mortar as you build.Seal vertical joint with proprietary flexiblesealant.

30

1. IDENTIFICATION

Expamet Construction Fixings

Expamet Building Products Limited

Greatham Street

Longhill Industrial Estate (North)

Hartlepool TS25 1PR

Tel: +44 (0)1429 866688

Fax: +44 (0)1429 866633

2. HAZARDS IDENTIFICATION

Possible cuts from steel edges.

Toxic and irritant fumes from high temperatures.

3. COMPOSITION

Galvanised steel

DX51D+Z275 to BS EN 10327: 2004

DX51D+Z600 to BS EN 10327: 2004

S280GD+Z275 to BS EN 10326: 2004

Stainless steel

1.4301 to BS EN 10088-1: 2005

4. FIRST AID MEASURES

Skin and eye contact: treat cuts from steel edges as required.

Ingestion: not applicable.

Inhalation: remove from source of fumes and dust.

5. FIRE FIGHTING MEASURES

Non-flammable material.

6. ACCIDENTAL RELEASE MEASURES

Not applicable.

7. HANDLING AND STORAGE

Bands and straps must not be used for lifting.

Use suitable PPE when handling the Construction Fixings.

Assess manual handling risks before lifting.

Construction Fixings should be stacked on firm level ground

in dry conditions.

8. EXPOSURE CONTROLS

Wear personal protection such as gloves and safety goggles

when handling products.

Some products may have a film of soluble cutting fluid after

manufacture; therefore carry out personal hygiene, including

proper washing of hands, after contact.

9. PHYSICAL AND CHEMICAL PROPERTIES

Construction Fixings are supplied in various lengths,

widths and gauges.

Metallic grey appearance.

10. STABILITY AND REACTIVITY

Construction Fixings are stable under normal conditions but

if subjected to high temperatures, fumes are produced.

11. TOXICOLOGICAL INFORMATION

High temperatures can produce fumes.

12. ECOLOGICAL INFORMATION

No known hazard.

13. DISPOSAL CONSIDERATIONS

Recycle or dispose of in accordance with Waste Management

Licensing Regulations.

14. TRANSPORT INFORMATION

Not classified as hazardous for transport.

15. REGULATORY INFORMATION

Construction Fixings are articles and have no obligations

under REACH.

16. OTHER INFORMATION

All products must be installed in accordance with Expamet

Building Products’ published instructions.

Where structural products are to be removed from an

existing installation, care must be taken to ensure that the

procedure does not compromise the loading/installation

restrictions applicable to the products.

The Construction Fixings Health and Safety Data Sheet is not

a product specification guide.

CONSTRUCTION FIXINGSHEALTH AND SAFETYDATA SHEET

Any arrangement of construction fixings shown in this brochure is indicative only. Actual fixing installations must comply with current Health and Safety requirements.

QUALITY YOU CAN TRUSTExpamet are not only industry leaders in the UK, but we also operate in continental Europe and the Middle East, giving

us a strong continental presence. You can be assured that wherever you are you can source a range of Expamet

building products.

EXTENSIVE PRODUCT RANGEExpamet Building Products Limited is the parent company of a number of great brands – with each brand committed to

quality in its particular product field.

Expamet Construction - One stop shop for metalwork for the construction industry

BAT – Builders’ metalwork products

Expamet – Plasterers’ accessories

Hy-Rib® – Permanent formwork for concrete

Power-Tie – Wall ties and ancillary fixings

Expamet Express® – Our new next-day delivery service

TECHNICAL AND SALES SUPPORTExpamet provide a comprehensive pre and post-sales support service. From product advice and training through

to design and implementation. Our sales and technical support teams have a wealth of construction and engineering

experience and are available for both on and off-site support.

For more information call us on +44 (0)1429 866655.

Order before 1pm and we will despatch your order for next working day delivery,

direct to branch or site.

See www.expamet.co.uk for full details

Quality Assurance BS EN ISO 9001:2008 and ISO 14001 2004 Registered Firms Certificate No. FM36694, EMS 45225

EXPAMET BUILDING PRODUCTS LIMITED

UK SALES AND DISTRIBUTION CENTRE

Greatham Street, Longhill Industrial Estate (North),

Hartlepool TS25 1PR England

Tel: Sales: +44 (0)1429 866611 Sales Fax: +44 (0)1429 866622

E-mail: [email protected]

General: +44 (0)1429 866688 Fax: +44 (0)1429 866633

Technical: +44 (0)1429 866655

Tech E-mail: [email protected]

Website: www.expamet.co.uk

IRISH SALES OFFICE

DUBLIN: Unit 7, Swords Business Park, Swords, Co. Dublin

Tel: +353 (0) 1890 2392 Fax: +353 (0) 1890 2220

E-mail: [email protected]

May 2011

Expamet operate a continuous development programme and we reserve the right to amend specification without prior notification.

Please note, some products are not manufactured by Expamet and are therefore excluded from registration to BS EN 9001: 2008.

Please contact the technical department for further information.

All copyright, trade marks and unregistered design rights for the products detailed in this brochure are the property of Expamet Building Products Ltd.

BUILDERS’ METALWORK - Amazon Web Services · BUILDERS’ METALWORK CI/SfB 21.9 Xt6. Page...

Documents

Transcript of BUILDERS’ METALWORK - Amazon Web Services · BUILDERS’ METALWORK CI/SfB 21.9 Xt6. Page...