Vibrational spectral analysis, XRD-structure, computation ...
B.tech(Vibrational Analysis)-2012
-
Upload
soumyajit-sengupta -
Category
Documents
-
view
358 -
download
0
description
Transcript of B.tech(Vibrational Analysis)-2012
![Page 1: B.tech(Vibrational Analysis)-2012](https://reader033.fdocuments.us/reader033/viewer/2022051110/54befdb74a7959267d8b45cd/html5/thumbnails/1.jpg)
1
S C H O O L O F M E C H A N I C A L E N G I N E E R I N G , K I I T U N I V E R SI T Y
Under the expert guidance and mentorship of
Prof. Isham Panigrahi
VIBRATIONAL ANALYSIS OF CANTILEVER ROTOR IN VISCOUS MEDIUM
![Page 2: B.tech(Vibrational Analysis)-2012](https://reader033.fdocuments.us/reader033/viewer/2022051110/54befdb74a7959267d8b45cd/html5/thumbnails/2.jpg)
2
S C H O O L O F M E C H A N I C A L E N G I N E E R I N G , K I I T U N I V E R SI T Y
Presences of cracks in rotating shafts are serious threats to its performance. detection of crack in
rotors needs urgent attention.
Precautions should be taken much earlier as crack propagates quicker in rotating shafts due to fatigue
loading.
Cracks are the major causes of failure, investigation for vibration analysis of rotor with cracks are essential for
safe design.Viscous medium, the analysis of critical speed becomes complex.
INTRODUCTION-CRACKS IN A SHAFT/BEAM
![Page 3: B.tech(Vibrational Analysis)-2012](https://reader033.fdocuments.us/reader033/viewer/2022051110/54befdb74a7959267d8b45cd/html5/thumbnails/3.jpg)
3
S C H O O L O F M E C H A N I C A L E N G I N E E R I N G , K I I T U N I V E R SI T Y
The analysis of a cracked rotating shaft in viscous medium will be utilized for
I )condition monitoring II ) for early crack detection in rotor for vibration of
(a) high-speed rotor in centrifuges(prone to fatigue)
(b) high-speed boring machine (c) rotors used for drilling oil from sea bed
III) preventing failure of rotors used in machineries subjected to various environmental conditions.
PRACTICAL APPLICATIONS OF CRACK INVESTIGATION IN SHAFTS AND
BEAMS
![Page 4: B.tech(Vibrational Analysis)-2012](https://reader033.fdocuments.us/reader033/viewer/2022051110/54befdb74a7959267d8b45cd/html5/thumbnails/4.jpg)
4
S C H O O L O F M E C H A N I C A L E N G I N E E R I N G , K I I T U N I V E R SI T Y
The phases of the process plan for the present Investigation are as follows:
• Dynamic analysis of cracked cantilever rotor without viscous medium.
• Dynamic analysis of cracked cantilever rotor in viscous medium.
OBJECTIVES OF THE PROJECT
![Page 5: B.tech(Vibrational Analysis)-2012](https://reader033.fdocuments.us/reader033/viewer/2022051110/54befdb74a7959267d8b45cd/html5/thumbnails/5.jpg)
5
S C H O O L O F M E C H A N I C A L E N G I N E E R I N G , K I I T U N I V E R SI T Y
Cracks introduce new boundary conditions for the structures at the crack locations. These boundary
conditions are derived from the strain energy equation using Castigliano’s theorem.
Presence of crack also reduces stiffness of the structures which has been derived from stiffness matrix.
Euler-Bernoulli beam theory is used for dynamic characteristics of beams with transverse cracks.
Timoshenko Beam theory is successfully used for vibration analysis of cracked shaft.
IMPORTANT THEORIES AND METHODS USED FOR THE ANALYSIS
![Page 6: B.tech(Vibrational Analysis)-2012](https://reader033.fdocuments.us/reader033/viewer/2022051110/54befdb74a7959267d8b45cd/html5/thumbnails/6.jpg)
6
S C H O O L O F M E C H A N I C A L E N G I N E E R I N G , K I I T U N I V E R SI T Y
The dynamic response of rotors with transverse cracks rotating in viscous
medium, the amplitude of vibration of rotors are found using Navier-Stokes
equation and Fourier transform technique.
IMPORTANT THEORIES AND METHODS USED FOR THE ANALYSIS
![Page 7: B.tech(Vibrational Analysis)-2012](https://reader033.fdocuments.us/reader033/viewer/2022051110/54befdb74a7959267d8b45cd/html5/thumbnails/7.jpg)
7
S C H O O L O F M E C H A N I C A L E N G I N E E R I N G , K I I T U N I V E R SI T Y
An electric motor
(203v,50hz,0.75amps,
1/8hp,93w,1350rpm)
A flexible coupling
APPARATUS REQUIRED
![Page 8: B.tech(Vibrational Analysis)-2012](https://reader033.fdocuments.us/reader033/viewer/2022051110/54befdb74a7959267d8b45cd/html5/thumbnails/8.jpg)
8
S C H O O L O F M E C H A N I C A L E N G I N E E R I N G , K I I T U N I V E R SI T Y
Bearing with housing
Dial indicator
![Page 9: B.tech(Vibrational Analysis)-2012](https://reader033.fdocuments.us/reader033/viewer/2022051110/54befdb74a7959267d8b45cd/html5/thumbnails/9.jpg)
9
S C H O O L O F M E C H A N I C A L E N G I N E E R I N G , K I I T U N I V E R SI T Y
Rotor
Weight of rotor = 1557.5 grams
Length of the shaft of the
rotor = 400mm = 40cm
Diameter of the shaft of
the rotor = 20mm = 2cm
Thickness of the disc of
the rotor = 15.5mm=1.55cm
Diameter of the disc of the rotor = 84mm = 8.40 cm
![Page 10: B.tech(Vibrational Analysis)-2012](https://reader033.fdocuments.us/reader033/viewer/2022051110/54befdb74a7959267d8b45cd/html5/thumbnails/10.jpg)
10
S C H O O L O F M E C H A N I C A L E N G I N E E R I N G , K I I T U N I V E R SI T Y
Stroboscope
![Page 11: B.tech(Vibrational Analysis)-2012](https://reader033.fdocuments.us/reader033/viewer/2022051110/54befdb74a7959267d8b45cd/html5/thumbnails/11.jpg)
11
S C H O O L O F M E C H A N I C A L E N G I N E E R I N G , K I I T U N I V E R SI T Y
EXPERIMENTAL SETUP
![Page 12: B.tech(Vibrational Analysis)-2012](https://reader033.fdocuments.us/reader033/viewer/2022051110/54befdb74a7959267d8b45cd/html5/thumbnails/12.jpg)
12
S C H O O L O F M E C H A N I C A L E N G I N E E R I N G , K I I T U N I V E R SI T Y
Volume of the rotor = volume of the shaft + volume of the disc
=3.14*40*(2*2)/4+3.14*1.55*(8.40*8.40)/4=211.6102cm3
density of the rotor = mass of the rotor / volume of the rotor
= 1557.5/211.6102= 7.3602 g / cm3 = 7360.2 kg / m3
Theoretically, C = (Modulus of rigidity / density of the rotor )1/2
= (80*109/7360.2)1/2
= 3.29*103 m/s .
THEORETICAL CALCULATION
APPROACH #1
![Page 13: B.tech(Vibrational Analysis)-2012](https://reader033.fdocuments.us/reader033/viewer/2022051110/54befdb74a7959267d8b45cd/html5/thumbnails/13.jpg)
13
S C H O O L O F M E C H A N I C A L E N G I N E E R I N G , K I I T U N I V E R SI T Y
Again, wn = (2n + 1)*3.14*C) / 2*l
wn = 3.14* C / (81.55/100)
wn = 12.66*10 3 rad/s
Therefore the natural frequency is fn = 12.66*10 3 / 2*3.14
fn= 2015.92 Hz
Therefore the theoretical rpm at which the first frequency occurs is = fn * 60
= 120955.4 rpm.
APPROACH #1(CONTD.)
![Page 14: B.tech(Vibrational Analysis)-2012](https://reader033.fdocuments.us/reader033/viewer/2022051110/54befdb74a7959267d8b45cd/html5/thumbnails/14.jpg)
14
S C H O O L O F M E C H A N I C A L E N G I N E E R I N G , K I I T U N I V E R SI T Y
Now following another approach to find out the natural frequency
Stiffness of any beam is given by Kt = 3.14*G*d4 / 32*l
Kt = 3140
Polar moment of inertia of a beam is given by J0 = density * height of the rotor * 3.14 * (D)4 / 32
J0 = 1.7 * 10-3
Now to find out wn = ( Kt / Jo )
wn = 1359.065 rad/sec .
Therefore the natural frequency is fn = Wn / 2*3.14
fn= 216.411 Hz
Therefore the theoretical rpm at which the first frequency occurs is = fn * 60
= 12984.66 rpm.
APPROACH #2
![Page 15: B.tech(Vibrational Analysis)-2012](https://reader033.fdocuments.us/reader033/viewer/2022051110/54befdb74a7959267d8b45cd/html5/thumbnails/15.jpg)
15
S C H O O L O F M E C H A N I C A L E N G I N E E R I N G , K I I T U N I V E R SI T Y
WITHOUT CRACK IN AIR
1.Deflection in air
At 1446 rpm Deflection shown by the vibration meter = 0.05mm Dial indicator reading = 0.1 mm At 847 rpm Deflection shown by the vibration meter = 0.95 mm Dial indicator reading = 0.9 mm At 331 rpm Deflection shown by the vibration meter = 1.123 mm Dial indicator reading = 1.2 mm
EXPERIMENTAL ANALYSIS
![Page 16: B.tech(Vibrational Analysis)-2012](https://reader033.fdocuments.us/reader033/viewer/2022051110/54befdb74a7959267d8b45cd/html5/thumbnails/16.jpg)
16
S C H O O L O F M E C H A N I C A L E N G I N E E R I N G , K I I T U N I V E R SI T Y
2 .Deflection in water
At 1446 rpm
Deflection shown by the vibration meter = 0.18 mm
Dial indicator reading = 0.2 mm
At 847 rpm
Deflection shown by the vibration meter = 0.78mm
Dial indicator reading = 0.7 mm
At 331 rpm
Deflection shown by the vibration meter = 1.87 mm
Dial indicator reading = 1.9 mm
EXPERIMENT ANALYSIS(CONTD.)
![Page 17: B.tech(Vibrational Analysis)-2012](https://reader033.fdocuments.us/reader033/viewer/2022051110/54befdb74a7959267d8b45cd/html5/thumbnails/17.jpg)
17
S C H O O L O F M E C H A N I C A L E N G I N E E R I N G , K I I T U N I V E R SI T Y
3. Deflection in flour-water
At 1446 rpm Deflection shown by the vibration meter = 0.57 mm Dial indicator reading = 0.6 mmAt 847 rpm Deflection shown by the vibration meter = 1.12 mm Dial indicator reading = 1.2 mm At 331 rpm Deflection shown by the vibration meter = 1.93 mm Dial indicator reading = 1.9 mm
EXPERIMENTAL ANALYSIS(CONTD.)
![Page 18: B.tech(Vibrational Analysis)-2012](https://reader033.fdocuments.us/reader033/viewer/2022051110/54befdb74a7959267d8b45cd/html5/thumbnails/18.jpg)
18
S C H O O L O F M E C H A N I C A L E N G I N E E R I N G , K I I T U N I V E R SI T Y
WITH CRACK IN ROTOR
1. DEFLECTION IN AIR
At 1446 rpm Deflection shown by the vibration meter = 0.06 mm Dial indicator reading = 0.1 mmAt 847 rpm Deflection shown by the vibration meter = 0.85 mm Dial indicator reading = 0.9 mm At 331 rpm Deflection shown by the vibration meter = 1.341 mm Dial indicator reading = 1.5 mm
EXPERIMENTAL ANALYSIS(CONTD.)
![Page 19: B.tech(Vibrational Analysis)-2012](https://reader033.fdocuments.us/reader033/viewer/2022051110/54befdb74a7959267d8b45cd/html5/thumbnails/19.jpg)
19
S C H O O L O F M E C H A N I C A L E N G I N E E R I N G , K I I T U N I V E R SI T Y
2.DEFLECTION IN WATER
At 1446 rpm
Deflection shown by the vibration meter = 0.23 mm
Dial indicator reading = 0.3 mm
At 847 rpm
Deflection shown by the vibration meter = 0.95 mm
Dial indicator reading = 0.9 mm
At 331 rpm
Deflection shown by the vibration meter = 1.8 mm
Dial indicator reading = 1.8 mm
EXPERIMENTAL ANALYSIS(CONTD.)
![Page 20: B.tech(Vibrational Analysis)-2012](https://reader033.fdocuments.us/reader033/viewer/2022051110/54befdb74a7959267d8b45cd/html5/thumbnails/20.jpg)
20
S C H O O L O F M E C H A N I C A L E N G I N E E R I N G , K I I T U N I V E R SI T Y
3. DEFLECTION IN FLOUR WATER
At 1446 rpm
Deflection shown by the vibration meter = 1.82 mm
Dial indicator reading = 1.8 mm
At 847 rpm
Deflection shown by the vibration meter = 1.20 mm
Dial indicator reading = 1.3 mm
At 331 rpm
Deflection shown by the vibration meter = 0.67 mm
Dial indicator reading = 0.6 mm
EXPERIMENTAL ANALYSIS(CONTD.)
![Page 21: B.tech(Vibrational Analysis)-2012](https://reader033.fdocuments.us/reader033/viewer/2022051110/54befdb74a7959267d8b45cd/html5/thumbnails/21.jpg)
21
S C H O O L O F M E C H A N I C A L E N G I N E E R I N G , K I I T U N I V E R SI T Y
0 5 10 15 20 250
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
IN AIR WITHOUT CRACK
Frequency
Dis
pla
cem
ent
RESULT AND DISCUSSIONS
![Page 22: B.tech(Vibrational Analysis)-2012](https://reader033.fdocuments.us/reader033/viewer/2022051110/54befdb74a7959267d8b45cd/html5/thumbnails/22.jpg)
22
S C H O O L O F M E C H A N I C A L E N G I N E E R I N G , K I I T U N I V E R SI T Y
0 5 10 15 20 250
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
Frequency
Dis
pla
cem
ent
IN WATER(WITHOUT CRACK)
![Page 23: B.tech(Vibrational Analysis)-2012](https://reader033.fdocuments.us/reader033/viewer/2022051110/54befdb74a7959267d8b45cd/html5/thumbnails/23.jpg)
23
S C H O O L O F M E C H A N I C A L E N G I N E E R I N G , K I I T U N I V E R SI T Y
IN FLOUR-WATER WITHOUT CRACK
0 5 10 15 20 250
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
Frequency
Dis
pla
cem
ent
![Page 24: B.tech(Vibrational Analysis)-2012](https://reader033.fdocuments.us/reader033/viewer/2022051110/54befdb74a7959267d8b45cd/html5/thumbnails/24.jpg)
24
S C H O O L O F M E C H A N I C A L E N G I N E E R I N G , K I I T U N I V E R SI T Y
0 5 10 15 20 250
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
Frequency
Dis
pla
cem
ent
IN AIR(WITH CRACK)
![Page 25: B.tech(Vibrational Analysis)-2012](https://reader033.fdocuments.us/reader033/viewer/2022051110/54befdb74a7959267d8b45cd/html5/thumbnails/25.jpg)
25
S C H O O L O F M E C H A N I C A L E N G I N E E R I N G , K I I T U N I V E R SI T Y
IN WATER(WITH CRACK)
0 5 10 15 20 250
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
Frequency
Dis
pla
cem
ent
![Page 26: B.tech(Vibrational Analysis)-2012](https://reader033.fdocuments.us/reader033/viewer/2022051110/54befdb74a7959267d8b45cd/html5/thumbnails/26.jpg)
26
S C H O O L O F M E C H A N I C A L E N G I N E E R I N G , K I I T U N I V E R SI T Y
IN FLOUR-WATER(WITH CRACK)
0 5 10 15 20 250
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
Frequency
Dis
pla
cem
ent
![Page 27: B.tech(Vibrational Analysis)-2012](https://reader033.fdocuments.us/reader033/viewer/2022051110/54befdb74a7959267d8b45cd/html5/thumbnails/27.jpg)
27
S C H O O L O F M E C H A N I C A L E N G I N E E R I N G , K I I T U N I V E R SI T Y
1)Presence of crack in rotor makes significant difference in amplitude of vibration to that of
uncracked one when rotates in a fluid medium. viscosity of fluid medium increases, the critical
speed of the rotor decreases along with the amplitude of vibration.
2)Amplitude of transverse vibration of the rotor system increases with the increase in the radius of
the container carrying the fluid.
CONCLUSION
![Page 28: B.tech(Vibrational Analysis)-2012](https://reader033.fdocuments.us/reader033/viewer/2022051110/54befdb74a7959267d8b45cd/html5/thumbnails/28.jpg)
28
S C H O O L O F M E C H A N I C A L E N G I N E E R I N G , K I I T U N I V E R SI T Y
3)Due to the presence of crack, the critical speed of rotor decreases.
4)Due to low critical speed the damping coefficient increases for which, the dimensionless amplitude of the
rotating cracked shaft. Due to low critical speed the damping coefficient increases for which, the dimensionless amplitude of the rotating cracked shaft is lowest when measured along the crack direction and is the highest in uncracked one for
the same type of viscous fluid.
5)External damping has got more impact in reducing the amplitude of vibration than in changing the resonance speed.
CONCLUSION(CONTD.)
![Page 29: B.tech(Vibrational Analysis)-2012](https://reader033.fdocuments.us/reader033/viewer/2022051110/54befdb74a7959267d8b45cd/html5/thumbnails/29.jpg)
29
S C H O O L O F M E C H A N I C A L E N G I N E E R I N G , K I I T U N I V E R SI T Y
1)Bearing characteristics for rotor systems play an important role on its dynamic behavior, which can be
incorporated in the theory for higher accuracy.
2)Gyroscopic effect which has not been considered in the present analysis can be taken into account.
3)Stability analysis of cracked structures can be included in the present study.
FURTHER WORK
![Page 30: B.tech(Vibrational Analysis)-2012](https://reader033.fdocuments.us/reader033/viewer/2022051110/54befdb74a7959267d8b45cd/html5/thumbnails/30.jpg)
30
S C H O O L O F M E C H A N I C A L E N G I N E E R I N G , K I I T U N I V E R SI T Y
KITO, F., Trans Japan Society of Mechanical Engineering (in Japanese), vol. 22, No. (1956-9), pp663.
Iida, S., Trans, Japan Society of Mechanical Engineers (in Japanese), Vol.24, No.141 (1958-5), pp278, 283; Vol.25,
No.151 (1959-3), pp.235.
Fritz, R.J., the effects of an annular fluid on the vibrations of a long rotor, part1-theory, journal of Basic Engineering,
Vol.92, No.4 (1970-12), pp923-929.
Fritz, R.J., the effects of an annular fluid on the vibrations of a long rotor, part2-test, journal of Basic Engineering,
Vol.92, No.4 (1970-12), pp930-935.
Brennen, C., on the flow in an annulus surrounding a whirling cylinder. Journal of Fluid Mechanics, Vol.75, part
1, 1976, pp.173-191.
Walson, W.H., Ames,W.F. and Clark.L.G., dynamic stability of rotating shafts in viscous fluids, journal of applied
Mechanics, june 1964,pp.291-299.
REFERENCE
![Page 31: B.tech(Vibrational Analysis)-2012](https://reader033.fdocuments.us/reader033/viewer/2022051110/54befdb74a7959267d8b45cd/html5/thumbnails/31.jpg)
31
S C H O O L O F M E C H A N I C A L E N G I N E E R I N G , K I I T U N I V E R SI T Y
Crighton,D.G.,Resonant oscillations of fluid-loaded struts, journal of sound and vibration, vol.87, no.3,1983,pp.429-
437.
Achenbach, J.D. and Qu, J., Resonant vibration of a submerged beam, journal of sound and vibration, vol.105
(2), 1986, pp.185-198.
Shimogo,T. and Krazao,Y., critical speed of rotor in a liquid, Bulletin of the JSME , Vol.25,No.200,1982,pp 276-283.
Kadyrov S.G., Wauer, J and Sorokin, S.V., a potential technique in the theory of interaction between a structure
and a viscous, compressible fluid, Archive of Applied Mechanics 71, 2001, pp.405-417.
Seeman, R. and Wauer, J., Finite oscillatory motion of a body immersed in an inviscid fluid at rest, and Stochastic
Dynamics ,AMD-Vol.192/DE- Vol.78,ASME 1994,pp.135-141.
Seeman, R. and Wauer, J., Fluid- structural coupling of vibrating bodies in contact with a fluid, Proceeding 3rd
Polish-German Workshop on Dynamical Problems in Mechanical Systems,1993,pp.31-42.
REFERENCE(CONTD.)
![Page 32: B.tech(Vibrational Analysis)-2012](https://reader033.fdocuments.us/reader033/viewer/2022051110/54befdb74a7959267d8b45cd/html5/thumbnails/32.jpg)
32
S C H O O L O F M E C H A N I C A L E N G I N E E R I N G , K I I T U N I V E R SI T Y
We have been highly obliged to undertake this project as part of our curriculum for
B.Tech and would like to extend our warmest regards for our Mentor-cum-Guide
Prof.Isham Panigrahi and our Respected Dean.Prof(Dr.)K.C.Singh for helping us
through the entire duration of the project with their expertise and valuable insights.
Group-14Mechanical EnggBatch:2008-2012
THANK YOU