Broucher Ceiling
-
Upload
arthur-lancelot -
Category
Documents
-
view
73 -
download
18
Transcript of Broucher Ceiling
INTERARCH BUILDING PRODUCTS PVT. LTD.AN ISO 9001-2000 COMPANY
Central Marketing OfficeB-30, Sector 57, NOIDA - 201 301, INDIA
Tel.: 0120 - 4170200/2581300/2581029, Fax : +91-120-2581017E-mail: [email protected] | www.interarchbuildings.com
NNOVATE NITIATE NTEGRATE
CEILINGS
Interarch UNIT 1, Greater NOIDA, UP, IndiaInterarch UNIT 1, Greater NOIDA, UP, India
Interarch Building Products Pvt. Ltd. commenced
operations in 1984, and pioneered the high-end metal
interior products market in India. Today, 25 years later,
Interarch is proud to be the largest Turnkey
Pre-Engineered Steel Construction Solution provider in
India with more than 40% market share in this segment.
Interarch has been a large and integrated manufacturer of
Pre-Engineered Building Systems with in-house Design,
Manufacture, Logistics, Supply and Project Execution
capabilities.
Introduction
NNOVATE NITIATE NTEGRATE
®TRAC Ceilings
®INTERARCH introduced TRAC lineal metal ceilings in 1984. Today,
INTERARCH is the largest manufacturer of metal building systems in India,
and the product range includes pre-engineered steel buildings, metal
roofing and cladding systems, metal and gypsum suspended ceilings and
window covering products. All manufacturing facilities are ISO 9001
certified by Underwriters Laboratories Inc., USA.
® TRAC ceiling systems set the trend and command a very high market share ®in India. The TRAC range of metal and Glass Reinforced Gypsum ceilings
are specially designed for the Indian market, taking into account of building
design, construction practices and weather conditions.
150C Ceiling System
200F Ceiling System
Curved Panel 84R
Inside Curve
84R Curved Panel Ceiling
Ceiling: Functional Features
CONCEALING SERVICES
Ceilings are primarily installed to conceal services such as HVAC ducting and
lighting. The covering up of services necessitates access to the ceiling
plenum. Accessibility to the ceiling plenum for maintenance is the most
important factor while selecting a suspended ceiling system.
84C Ceiling System
GRG Open Cell Ceiling
Panel Splice
Carrier Splice
®All TRAC ceilings are designed to allow easy access. Panels or tiles may be
lifted out or clipped off for maintenance or installation of concealed services.
AESTHETICS
Ceilings are often provided to create attractive interiors. ceilings
offer several options to the designer to match aesthetics with function.
®TRAC
ACOUSTICS
Suspended acoustical ceilings serve to provide sound absorption on the
most useful surface in a room. They help in reducing reverberant sound ® intensity within a room. TRAC ceilings are the most efficient sound
absorbing ceilings available in the market today.
Human activity in offices and large public spaces generates noise resulting in
reduced work efficiency. Acoustical (sound absorbing) ceiling systems help in
reducing build-up of reverberant noise because of their excellent sound
absorbing properties. This leads to a better working environment and
reduced annoyance due to high noise levels.
Main Runner
Outside Curve
Hook & Butterfly Clip
GRG Open Cell Ceiling
Cross Tee
1 2NNOVATE NITIATE NTEGRATE
ACOUSTICS
SOUND ABSORPTION
Noise is major concern when designing indoor spaces. Room sound
absorption is one of the most important factors in controlling built-up
reverberant noise and in reducing sound transmission between rooms.
When specifying the ceiling, the architect should ensure that the
specifications incorporate acoustic performance requirements.
The sound absorbing efficiency of material is designated by its sound
absorption coefficient (a). This is usually measured and reported in octave
bands over the frequency range of 125-4000 Hz, together with the Noise
Reduction Coefficient (NRC), which is the average of the sound absorption
coefficient at 250, 500, 1000 and 2000 Hz. Sound absorption coefficient ®data is given for all TRAC ceilings. This enables calculation of noise
reduction or reverberation time.
The increasing use of hard finishes and stone/tile finishes in offices requires ®the use of highly sound absorbent ceilings. TRAC ceilings offer NRC values
of 0.75 upto 1.05 for different ceiling types.
Traditionally, whenever sound absorption is required, perforated metal
ceiling panels are backed with a sound absorbing layer of mineral wool or
fiberglass. The use of a fibrous sound absorbing medium always has other
drawbacks. These include the difficulty in working with the fibrous materials
because of skin irritation and the problem of fibers letting loose into the air
stream in an air-conditioned environment.
® ® TRAC Acousti-Panel ceilings overcome these problems. This ceiling range
comprises perforated panels with an acoustic nonwoven factory applied to
the rear of the panels. Due to the controlled sound impedance of this ®perforated panel, and with a backing air space (ceiling plenum), the TRAC
®Acousti-Panel provides excellent sound absorption properties without the
use of any fibrous material behind the perforated panel. Please refer to
product data sheets for availability information.
SOUND TRANSMISSION LOSS
Sound transmission loss is a measurement of sound insulation between one
room and another. Some manufacturers provide sound transmission loss
(attenuation) values for ceiling tiles. This information is of doubtful utility
because ceiling tiles are supported on grids and have penetrations through
them to accommodate light fittings and air conditioning diffusers. The overall
sound transmission loss of such a composite ceiling will be 10-20 dB lower
than the transmission loss of the ceiling panel or tile alone.
When designing for sound insulation between rooms, the partition
separating the rooms is of major concern. To prevent flanking sound
transmission through the suspended ceiling, it is important that partitions do
not stop at the ceiling, but are extended right up to the roof slab above. The
suspended ceiling should not be relied upon to give sound insulation
between adjacent spaces.
FIRE RESISTANCE
All ceilings provide Class 1 Surface Spread of Flame in accordance with BS 476-part 7 (1987). The materials are incombustible as per BS 476-part 4
(1970) and satisfy Class O as per BS 476-part 6 (1989).
® TRAC
Sound Absorption Data Perforated Metal Tile
Perforated Tile with Non-Woven Acoustic
®TRAC - THE ENVIRONMENT FRIENDLY CEILING
All ceilings are manufactured from fully recyclable materials.
ceilings are pre-painted and fully pre-fabricated in the factory. The ceiling
systems are friendly to handle, and will not promote growth of bacteria or
fungi.
®TRAC ceilings exhibit excellent corrosion resistance. They can withstand
very high humidity (upto 100%) and are suitable for use in outdoor areas.
® ®TRAC TRAC
When selecting a suspended ceiling, the designer needs to weigh the costs ®and performance requirements. There is a TRAC ceiling for every need.
Ceilings systems are available in gypsum, coated steel and coated ® aluminium. TRAC ceilings are available in a variety of designs including lineal
ceilings, clip-in or lay-in tile and plank ceilings, and C-grid (band raster)
ceilings. Metal ceilings are manufactured in aluminium and steel with coil
coated or powder coated finishes. All metal ceilings are available in a
perforated version for sound absorption, and are designed to integrate with
standard lighting fixtures, air diffusers, and partitions.
Please refer to detailed product data sheets for specific applications.
GRG (Glass Reinforced Gypsum) Ceiling System
84R Lineal CeilingC-Grid (band raster) Ceiling
®TRAC The Right Ceiling for you
Frequency, Hz 125 250 500 1k 2k 4k NRC
84C Wool/200mm air space
perf/25mm Mineral 0.38 0.90 1.08 1.02 1.10 0.79 1.03
84R Wool/200mm air space
perf/25mm Mineral 0.22 0.69 0.96 0.91 0.96 0.86 0.88
150C Wool/200mm air space
perf/25mm Mineral0.30 0.74 0.88 0.58 0.71 0.70 0.73
Perf Wool/200mm air space
tile/25mm Mineral0.50 1.00 1.02 1.07 1.06 1.05 1.04
Perf Wool/200mm air space
tile/acoustic
0.48 0.93 0.62 0.69 0.80 0.75 0.76
Mineral Fiber Tile 0.13 0.29 0.47 0.58 0.57 0.54 0.48
0.09 0.10 0.10 0.12 0.25 0.35 0.14GRG T 206, no holes
GRG T 206, no holes/25MW 0.20 0.40 0.55 0.10 0.21 0.50 0.32
38 mm
24 mm
38 mm
3 4NNOVATE NITIATE NTEGRATE
84 16
FLUSH PROFILE(OPTIONAL)
16
473
1
32
THE RIGHT CEILING FOR THE RIGHT APPLICATION
INTERARCH is a pioneer of coated metal architectural products in India and
has a consistent record of product innovation. Over the years, millions of
square metres of INTERARCH architectural building products have been
installed in India and abroad.
®TRAC ceilings are available in a wide range of panel types for decorative ®and functional applications. TRAC ceilings are suitable for use in interior and
exterior areas in offices, hospitals, schools, restaurants, shops, hotels, ®airports and other buildings. TRAC ceilings are also suitable for industrial
use and are specially suited to aggressive environments inside factory
buildings.
DESIGN AND ENGINEERING SUPPORT
The Interarch Architectural Projects and Service Group (ASG) provides
customers with complete design, engineering, and drafting support.
ASG can help you convert your most imaginative designs into reality. Shop
drawings and detailed bill of quantities are prepared for all projects to ensure
correct product supply and application.
84R Interior & Exterior Ceilings
84R INTERIOR
Material
Panels: 84mm wide x 16mm deep, made out of 0.50mm aluminium alloy
AA3005/ 5052 with stove enamelled coil coated finish / 0.45
galvanised steel with stove enamelled coil coated finish.
® (Colour according to TRAC colour chart and availability chart)
Panel length upto approx 5m
When perforated, hole diameters are 2mm on 5mm centres (standard) or
1mm on 2.5mm centres (microperforated), the holes representing15% of
the perforated area.
Panel Carriers: 32mm wide, 39mm deep, made out of 0.95mm
aluminium alloy AA 5052/0.6mm galvanised steel, with prongs to hold the
panels in a module of 90mm/100mm (gap 6/16mm, open). Optional gap
closures with recessed or flush join profiles for 16mm gap.
3105/
Flush join Profiles : Made of enamelled aluminium, for 100mmmodule
(16mm gap).
Suspension: By means of suspension rods and spring clips. One suspension
for every 1.5 to 2 sq.m.
Panel Span: 1.3m max. with insulation, 1.5m max. without insulation.
Carrier Span: 1.3m max. spacing of suspension rods.
Finish
Coil Coated: Panels will be finished on exposed side with 20 microns
polyester coil coating over primer and on rear side with a wash coat.
84R EXTERIOR
Material
Panels: 84mm wide x 16mm deep, made out of 0.60mm aluminium alloy
AA 3005 / 3105 / 5052 with stove enamelled coil coated finish.
®(Colour according to TRAC colour chart and availability chart)
Panel length upto approx 5m
Stringers: 34.5mm wide, 48mm deep, made out of 0.95mm aluminium
alloy 5052, with prongs to hold the panels in a module of 90mm / 100mm
(gap 6 / 16mm open). Optional gap closure with flush join profile for
16mm gap.
Suspension: By means of rigid suspension rods or on steel substructure.
Panel Span: 800mm max.
Stringer Span : 500mm max. spacing of suspension angles.
Finish
Coil Coated: Panels will be finished on exposed side with coil coated stove
enamelled PVF2 or polyurethane paint with a wash coat on the rear side.
32
39
16
84
5 5 À2
À12.5
2 5
®TRAC Ceilings
Sound Absorption Data
Frequency, Hz 125 250 500 1000 2000 4000 NRC
84R perf/25mm MineralWool/200mm air space 0.22 0.69 0.96 0.91 0.96 0.86 0.88
1.20
1.00
0.80
0.60
0.40
0.20
0.00
Absorption Coefficients
Frequency, HzFrequency, Hz
...84R perf/25mm MineralWool/200mm air space
125 250 500 1000 2000 4000 NRC
0.20 0.69 0.96 0.91 0.96 0.86 0.88
Abso
rpti
on C
oeff
icie
nt
5 6NNOVATE NITIATE NTEGRATE
84 16
45
12.5
32
39
12.5
12.5
32
84
184
5 5À2
À12.5
2 5
EXTERIOR
Material
Panels: 150mm wide x 17mm deep, made out of 0.60mm aluminium alloy
AA 3105 / 5050 with stove enamelled coil coated finish / 0.50mm galvanised
steel with stove enamelled coil coated finish.
(Colour according to Trac colour chart and availability chart)
Panel length up to approx 5m
Stringers: 34.5mm wide, 48mm deep made out of 0.95mm aluminium
alloy AA 5052/0.60mm galvanised steel, with prongs to hold the panels in
module of 150mm.
Suspension: By means of rigid suspension or mounted on a steel
sub-structure.
Panel Span: 1000mm max.
Stringer Span: 500mm max. spacing of suspension angles.
Finish
Coil Coated: Panels will be finished on exposed side with coil coated stove
enamelled PVF2/ polyurethane/SMP paint with a wash coat on rear side.
angles Sound Absorption Data
Frequency, Hz 125 250 500 1k 2k 4k NRC
150C Wool/200mm air space
perf/25mm Mineral 0.30 0.74 0.88 0.58 0.71 0.70
Sound Absorption Data
Frequency, Hz 125 250 500 1k 2k 4k NRC
84C Wool/200mm air space
perf/25mm Mineral0.38 0.90 1.08 10.2 1.10 0.79 1.03
1.20
1.00
0.80
0.60
0.40
0.20
0.00
Absorption Coefficients
125 250 500 1000 2000 4000 NRC
0.38 0.90 1.08 1.02 1.10 0.79 1.03
Frequency, Hz
84C perf/25mm Mineral Wool/200mmair space
Abso
rpti
on C
oeff
icie
nt,
1.00
0.80
0.60
0.40
0.20
0.00
Absorp
tion C
oeff
icie
nt,
150 C perf./25mm Mineral Wool /200 mm air space
Absorption Coefficients
125 250 500 1000 2000 4000 NRC
0.30 0.74 0.88 0.58 0.71 0.70 0.73
Frequency,Hz
SUSPENSION ANGLEAT 500mm C/C
SUSPENSION CLIP
PANEL CARRIER
150-C PANEL
EDGE COVER PROFILE
39
32
15
150/75
84C Ceiling System
0.73
84C/184C INTERIOR
Material
Panels:
23.5mm, made out of 0.50mm aluminium alloy AA 3005/3105/5052 with
stove enamelled coil coated finish 0.45mm galvanised steel with stove
enamelled coil coated finish.
®(Colour according to TRAC colour chart and availability chart)
Panel lengths up to approx. 5m
Panel carriers: 32mm wide, 39mm deep, made out of 0.95mm aluminium
alloy AA 5052/0.6mm galvanised steel, with cutouts to hold the panels in a
module of 100mm (84C) or 200mm (184C), gap 16mm closed.
Suspension: By means of suspension rods and spring clips. One
suspension for every 1.5 to 2 sq.m.
Panel Span: 1.3m max. with insulation, 1.6m max. without insulation.
Carrier Span: 1.3m max. spacing of suspension rods.
Finish
Coil Coated: Panels will be finished on exposed side with 20 microns
polyester coil coating over primer and on the rear side with a wash coat.
84mm/184mm wide x 12.5mm deep, with a recessed flange of
84C EXTERIOR
Material
84C ceilings can also be used for exterior applications when suspended by
rigid suspension rods or mounted on a steel substructure. 84C exterior
ceiling is available in 0.50mm aluminium alloy AA 3005/ 5052 with
stove enamelled coil coated finish.
(Colour according to colour chart and availability chart)
Panel Span: 800mm max.
Carrier Span: 500mm max. spacing of suspension angles.
Finish
Coil Coated: Panels will be finished on exposed side with coil coated stove
enamelled PVF2 or polyurethane paint with a wash coat on the rear side.
3105/
®TRAC
84C/184C Interior & Exterior Ceilings 150F/200F Interior & Exterior Ceilings/75C & 150C Interior
150F INTERIOR / EXTERIOR
INTERIOR
Material
Panels: 150mm wide x 17mm deep, made out of 0.60mm aluminium alloy
AA 3105 with stove enamelled coil coated finish / 0.50mm
galvanised steel with stove enamelled coil coated finish.
®(Colour according to TRAC colour chart and availability chart)
Panel length upto approx 5m
Stringers: 34.5mm wide, 48mm deep made out of 0.95mm aluminium
alloy AA5052/0.60mm galvanised steel, with prongs to hold the panels in a
module of 75 /150mm.
Suspension: By means of suspension rods and spring clips.
Panel Span: 1.5m max. with insulation, 1.8m max. without insulation.
Stringer Span: 1.5m max. spacing of suspension rods.
Finish
Coil Coated: Panels will be finished on exposed side with 20 microns
polyester coil coating over primer and on the rear side with a wash coat.
/3105/5052
75C/150C INTERIOR
® TRAC
because of its smooth, closed appearance. The panels about each other
with a narrow V-groove. They are installed to carrier profiles and can be
simply demounted individually, by inserting a plain strip between the
profiles.
®As with all TRAC ceilings, the 75C/150C can be applied in all types of
buildings and because of their closed appearance they are particularly
suitable for domestic applications: living rooms, kitchens, corridors etc.
Panels: 75mm/150mm wide x 15mm deep with bevelled groove between
panels, made out of 0.50mm thick aluminium alloy AA 3005/3105/5052 or
0.5mm thick galvanised steel.
®(Colour according to TRAC colour chart and availability)
Panel lengths upto approx 5 m.
When perforated, hole diameters are 2mm on 5mm centres (standard) or
1mm on 2.5mm centres (micro-perforated), the holes representing 15% of
the perforated area (150C only).
Panel Carriers: 32mm wide, 39mm deep made out of 0.95mm aluminium
of 0.6mm galvanised steel, with prongs to hold panel in a module of 15mm.
Suspension: By means of G.I. rod hangers and suspension clips.
Panel Span: 1.3m max. with insulation, 1.5m max. without insulation.
Carrier Span: 1.3m max. spacing of suspension rods.
Finish
Coil Coated: Panels will be finished on exposed side with 20 microns
polyster coil coating over primer and on the rear with a wash coat.
ceiling type 75/150C distinguishes itself from the other types
150/200
17
48
7 8NNOVATE NITIATE NTEGRATE
®TRAC tile and plank design ceiling system has been developed to meet
both practical and aesthetical requirements of modern ceilings. The major ®advantages of the TRAC tile/plank system are innovative suspension
systems, optional rigid grid system for suspension of exterior ceilings, choice
of tile material, extensive range of colours and finishes and a choice of
perforations and flexibility in design specially with the plank ceiling system.
The tile/plank ceiling systems are offered in stove enamelled coil coated
steel and aluminium and powder coated steel and aluminium finishes and
offer the advantage of easy cleaning, non-static properties and inert material.
Incandescent and halogen type spot lights can be easily incorporated in the
tile ceilings and fluorescent fittings within the plank ceilings.
Tiles
Tiles are manufactured out of coil coated galvanised steel/aluminium alloy
AA 3105 on advanced equipment, which includes several
levelling stages in the manufacturing process. For the clip-in tile, two sides of
each tile are raised and pipped and stopped to ensure positive engagement
into the spring tee yet allow demounting of individual tiles.
For the lay-in system, the tiles have a flange on each end which lays on the
exposed grid. All tiles have square/bevelled edges.
Planks
Planks are manufactured out of coil coated aluminium alloy
AA 3105/3005/5202 galvanised steel produced on advanced equipment
which includes several levelling stages.
Clip-in planks: The short sides of each plank are raised and pipped and
stopped to ensure positive engagement into the spring tee, yet allow
demounting of the individual planks
Lay-in and C-Grid planks: These planks have a flange on each end, which
lay on the exposed grid or C-grid. The planks can be laid and easily removed
without the aid of special tools. Planks over 1500mm in length have an
additional stiffening flange on the long side.
Suspension
Clip-in-system: Tiles/planks are suspended by means of a suspension
system comprising 0.5mm galvanised steel clip-in profiles installed at correct
spacing to support the tiles/planks. Suspension profiles are suspended from
roof structure by GI ceiling brackets. GI suspension angles and hold-on
clamps at max. 1200mm centre to centre along the clip in profile. This rigid
suspension is also suitable for exterior use.
Lay-in-System: Suspension system is standard 24mm table exposed metal
grid. Grid features 38mm high main runners and cross tees, roll formed
from galvanised steel to BS 2989 Z-18 zinc coating. The main runners
feature bayonet ends and the cross tees stab ends for quick and simple
coupling. The runners are pre-slotted to construct a variety of layouts. The
main and cross runners are provided with a coil coated steel capping on the
exposed table in off-white colour. The grid is suspended from the roof with
GI wire rod and quick adjustment suspension hangers along the runners.
The grid system is designed to satisfy ASTM C635 intermediate duty loading
and deflection criteria. This system is only suitable for interior use.
C-grid System: The suspension system consists of exposed C shaped
runners which are installed parallel to each other to form continuous main
/3005/5202
courses. Spacing between runners corresponds to the exposed length of
the plank. When a square grid is required, this is made by incorporating
shorter C-shaped cross members that are butt-jointed against the main
runner and tied with a special cross piece bracket. This system is only
suitable for interior use. The C runners are suspended from the roof slab
with special suspension shoes and GI suspension angles at a maximum
distance of 1200mm centre to centre.
Edge Cover Profile
Tiles/planks are trimmed along the wall perimeter by means of 19x19mm
roll formed steel or aluminium edge cover profile.
Paint Finish
Steel tiles/planks: Steel tiles/planks are finished on exposed side with 20
micron polyester coil coating over primer in approved shade and backing
coat on rear surface (nominal 5 microns), or with a 50 micron epoxy
polyester powder coating on exposed surface.
Aluminium tiles/planks: Aluminium tiles/planks are finished on exposed
side with 20 micron polyester coil coating over primer in approved shade
and backing coat on rear surface (nominal 5 microns), or with a 50 micron
epoxy polyester powder coating on exposed surface. Wall angles are
finished with 50 micron epoxy polyester powder coating paint in broken
white shade.
Perforations
®TRAC tiles and planks are also available with perforations for providing ® acoustic performance characteristics. TRAC tiles and planks are perforated
as a standard with 2.5mm dia. holes at 5.5mm centre to centre in a regular
pattern. Other special/non-standard perforations are also available. Tiles
and planks when backed with 25mm thick resin bonded mineral wool2(48 kg/m ) provide good sound absorption. Tiles and planks are also
available with a factory applied acoustic tissue to the back side, which
provides good sound absorption.
Sound Absorption Data
Frequency, Hz 125 250 500 1k 2k 4k NRC
Perf Tile/Acoustic tissue 0.93 0.62 0.69 0.80 0.75 0.76
Perf Tile/25mm Mineral Wool 1.041.051.061.071.021.000.50
0.48
1.20
1.00
0.80
0.60
0.40
0.20
0.00
Absorption Coefficients
Abso
rpti
on C
oeff
icie
nt,
Frequency, Hz
Perf tile/acoustic tissue
Perf tile/25mm Mineral Wool
125 250 500 1000 2000 4000 NRC
0.48 0.93 0.62 0.69 0.80 0.75 0.76
0.50 1.00 1.02 1.07 1.06 1.05 1.04
Tile & Plank Design CeilingsTiles and plank ceilings are available with clip-in, lay-in and C grid
suspension systems.
Clip-In System
The clip-in system consists of 0.5mm galvanised steel clip in profile which is
used as the primary suspension and if required, as a secondary suspension.
This system features:• a rigid grid system to ensure a level ceiling and
• a hidden suspension system for an uncluttered, monolithic ceiling appearance
Lay-In System
The lay-in system comprises the Trac 8011 exposed grid suspension. This
grid features stab-in coupling and is demountable.
This system features :
• easy access to the plenum
• a rigid fire rated grid to ensure a level ceiling and an exposed grid
suspension which accentuates the grid pattern
C-Grid Suspension System
The C-grid suspension system consists of exposed C-shaped runners which
are installed parallel to each other or in a square grid to form continuous
main courses. The planks are hooked onto these grids.
This system features:
• the advantage of the possibility to fix partition walls to the strong C-Grid
• an exposed wide suspension system which accentuates the grid pattern
and allows easy access to the plenum
Alternative Lay-Out
(TEGULAR)
WALL
HOOK AND BUTTERFLY CLIP
CROSS TEE
TRAC LAY- IN TILEEDGE COVER PROFILE TRAC L(SQUARE EDGE)
AY- IN TILE / PLANK
Lay-In System
0.7
METAL FASTENER
R.C.C. SLAB
CEILING BRACKET
SUSPENSION ANGLE
SUSPENSION SHOE
TRAC PLANKS
C-GRID C-GRID
WALL
C Grid Suspensions System
CEILING BRACKETAT 1200mm C/C
CUT EDGE OF PLANK(FOLDED UP) RESTINGON EDGE PROFILE
G.I. SUSPENSION ANGLEAT 1200 mm C/C
HOLD ON CLAMP’AT 1200MM C/C (Max.)
CLIP IN PROFILE
EDGE PROFILE
WALL
TRAC TILES/PLANKS
Clip-In System
D
X
e
f
g
d
Lay-In Plank
Straight Joints
Combined Tile Sizes
C-Grid Ceiling with Light Fittings
TRAC PLANKS
C-GRID
WALL
Code Size (mm) Material ThicknessWidth Length Aluminium Steel
TILES 600 600 0.7 0.5600 300 0.7 0.5
PLANKS 254 1264 0.7 0.6305 1264 0.7 0.6284 1247 0.7 0.6
Tiles and Plank Ceilings (Standard Available Sizes)
9 10NNOVATE NITIATE NTEGRATE
GRG TILES
TILES
Composition
The GRG range of ceiling tiles are manufactured from glass
reinforced gypsum and comprise non-combustible gypsum casting
plaster reinforced with a glass fibre membrane resulting in a light weight,
strong and prestressed panel.
Surface Finish
The plaster has a silky smooth or textured moulded finish.
Colour
The tiles are normally supplied in their natural white finish and can be
pre-decorated to order.
Dimensions
All designer tiles are designed for installation on a standard 600x600mm
module 24mm table exposed metal grid and are precision made to within
plus or minus 0.25mm
Weight
For a guide, the tile weights are shown below but may vary depending
upon the gypsum source.
®TRAC
TRAC GRG Ceiling®
Fire Performance
Non-combustibility: GRG tiles are rated non-combustible as
defined in BS 476: Part-4, 1970.
Surface Spread of Flame: GRG tiles are rated Class 1 for surface
spread of flame to BS 476: Part-7, 1987.
Fire Propagation: Test results to BS 476: Par-6, 1989 indicate a Class O
surface.
Smoke and Toxic Fume Emission: The tiles are zero rated for smoke
emission. No toxic fumes are given off.
Humidity Resistance
®TRAC
®TRAC
The tiles have excellent moisture resistance and can be used in areas of high
humidity including covered external areas, kitchens and bathrooms. Tested
in an atmosphere of 95% R.H. at 12°C for 14 days, the tiles did not sag or
Tile
T206 Fine Texture Tiles
T506 Travertine
T826 Shallow Coffers
T906 Open Cell Tiles
T906C Closed Cell Tiles T906C
T906
T826 T206
distort and showed only a minimal increase in weight. Unlike most other
ceiling materials, this important attribute can often be used to speed up the
building program by installing the ceiling before the building is fully
weathertight.
T506
3.9
3.9
4.5
4.15.6
10.8
10.8
12.5
11.414.5
0.60
0.50
0.40
0.30
0.20
0.10
0.00
Absorption Coefficients
Abso
rpti
on C
oeff
icie
nt, a
Frequency, Hz
GRG T 206, no holes/25 MW
GRG T 206, no holes
125 250 500 1000 2000 4000 NRC
0.20 0.40 0.55 0.10 0.21 0.50 0.32
0.09 0.10 0.10 0.12 0.25 0.35 0.14
Biological
GRG tiles will not support the growth of bacteria or other micro-
organisms.
Lifespan
Under normal conditions GRG tiles will not deteriorate and can be
expected to last the lifetime of the building.
Suspension
Suspension system is standard 24mm table exposed metal grid.
exposed metal grid systems are designed for maximum strength. The grid
features main runners and cross tees roll formed from galvanised steel. The
main and cross runners are provided with stab-in coupling for quick
installation. The runners are pre coated to construct a variety of lay outs.
Main and cross runners are provided with a coil coated steel capping on the
exposed table in off-white colour. Grid system features main and cross tees
38mm high. The grid is suspended from the roof with GI wire rods and or
quick adjustment suspension hangers at maximum 1200mm along the main
runners. GRG tiles are designed for lay-in mounting from below into
standard grid.
Transport, Handling and Storage
GRG tiles are supplied and packed in cardboard cartons. Cartons
should be transported and stacked in the vertical position only, never flat; the
stack should be a maximum of three cartons high. Similarly, tiles should be
stacked vertically when awaiting fixing.
Installation
Main tees should normally be fixed at 1200mm centres with hangers every
® TRAC
®TRAC
®TRAC
®TRAC
®TRAC
TRAC® GRG CEILINGS
Sound Absorption Data
Frequency, Hz 125 250 500 1k 2k 4k NRC
GRG T 206, no holes/25 MW 0.20 0.40 0.55 0.10 0.21 0.50 0.32
GRG T 206, no holes 0.09 0.10 0.10 0.12 0.25 0.35 0.14
1200mm along the length of the tee. The tees would be in filled with
1200mm and 600mm cross tees. The grid manufacturers
recommendations should be followed at all times.
Note: All perimeter tiles may be supported on only 3 sides without risk of
sagging. Tiles can easily be cut by using a carpenters fine tooth saw; the
lines should be placed face down on a flat, clean surface for cutting.
Kg/tile 2Kg/m
Texture Tiles
11 12NNOVATE NITIATE NTEGRATE
Accessories
LAY-IN SUSPENSION
HOOK AND BUTTERFLY CLIP110050
MAIN RUNNER850300
CROSS TEE (600MM)812300
CROSS TEE (1200MM)814300
WALL ANGLE144000
CEILING 150C
PANEL CARRIERST-432689.1863 (Black)AL-332689.1863 (Black)
CEILING 84C/184C/84R
PANEL CARRIERST-432686.1863AL-332686.1863
STRINGER V5 (84-R)AL-332185.1863
PANEL CARRIER(84-R 90mm MODULE)ST-432687.1863AL-332687.1863
CARRIER SPLICEAL-334173.1863
PANEL SPLICE (84-C)AL-334517.1863
CEILING 200F/CLIP IN TILE & PLANK
HOLD ON CLAMPST-440101.0000
HOLD ON CLAMP WITHADJUSTMENT CLIPST-440106.0000
CEILING BRACKETST-401144.0000
CLIP IN PROFILEST-440103.0000
SUSPENSION ANGLEST-401146.0000
CEILING 150F
PANEL SPLICEAL-334175.1863 (Black)AL-334175.0280 (Natural)
STRINGER V9ST-401850.1863AL-332186.1863
C-GRID SUSPENSION (AS PER C-GRID WIDTH)
SUSPENSION SHOEST-4021XX.0000
WALL CONNECTORST-4041XX.0000
C-GRIDST-4011XX.0000
CROSS CONNECTORST-4031XX.0000
CEILING 84R
FLUSH JOIN PROFILEAL-332104.0000
ROD HANGER1000MM ST-434878.0000500MM ST-434862.0000
SUSPENSION CLIPST-434795.0000
EDGE COVER PROFILE(W-SHAPED)ST-442414.1863
EDGE COVER PROFILE(L-SHAPED)ST-432408.0000AL-332406.0000
®List of major projects where TRAC ceiling system has been used
S.NO. NAME OF PROJECT LOCATION
1 National Thermal Power Corporation Faridabad
2 Power Grid Substation Satna / Raipur
3 Ansal Plaza Delhi
4 Indian Farmers Fertiliser Cooperative Limited Phulpur
5 GAIL (India) Limited Rajasthan / Gandhar
6 Rourkela Steel Plant Rourkela
7 Krishi Anusandhan Bhawan Pune
8 Mahindra & Mahindra Limited Mumbai
9 KFC Restaurant New Delhi
10 All India Institute of Medical Sciences New Delhi
11 CPWD New Delhi
12 Ericsson New Delhi
13 Defence Research and Development Organisation Srinagar
14 National Hydroelectric Power Corporation Ltd. Faridabad
15 Crompton Greaves West Bengal
16 Delhi Metro Rail Corporation Shastri Park
17 Punjab Institute of Medical Science Jalandhar
18 Control Room PGCIL All-India
Indian Oil Corporation Ltd. All-India
Bharat Petroleum Corporation Limited All-India
Reliance Petroleum Limited All-India
Mumbai Airport (International Terminal) Mumbai
Bangalore Airport (Public Lounge Area) Bangalore
Hyderabad Airport (Public Lounge Area) Hyderabad
Guwahati Airport Guwahati
Bhopal Airport Bhopal
Raipur Airport (Public Lounge Area) Raipur
Agartala Airport Agartala
Tezpur Airport Tezpur
R.R. Hospital New Delhi
Escorts Heart Institute New Delhi
Leelawati Hospital Mumbai
Indian Spinal Injuries Centre New Delhi
Apollo Hospital New Delhi
IGMH Hospital Maldives
PGI Hospital Chandigarh
19 PETROL PUMP CANOPIES
20 AIRPORTS
21 HOSPITALS
13 14NNOVATE NITIATE NTEGRATE
Regional Offices and Manufacturing Units
Interarch Building Products offer turnkey operations with regional offices and project control
centres for marketing, sales and coordination at all locations across India.
M/s. Interarch Building Products Pvt. Ltd.
Plot No: D-1/1, SIPCOT Industrial Park, Mambakkam,
Sriperembudur - 602 105
Kancheepuram (Tamil Nadu)
Tel: 044 - 27190710
M/s. Interarch Building Products Pvt. Ltd.
Plot No: A, Khasra No: 276-A,
2 KM on Kichha - Rudrapur Road,
Kichha - 263 148
Distt: Udham Singh Nagar (Uttarakhand)
Mob: 09760690304
For faster processing of enquiries from - , Chandigarh,Hyderabad, Indore, Kolkata, Kochi, Mumbai, Nagpur, Pune, please contact:
Ahmedabad, Bangalore, Baroda, Bhopal, Chennai
M/s. Interarch Building Products
Plot No: 29, Udyog Vihar,
Greater Noida - 201 306
Tel: 0120 - 4502300, Fax: 0120 - 2560793
M/s. Interarch Building Products Pvt. Ltd.
Plot No: 14, Sector - 2,
Integrated Industrial Estate, Pantnagar
Rudrapur - 263 153 (Uttarakhand)
Mob: 09319268211
Pvt. Ltd.
Central Marketing Office
B-30, Sector-57, Noida - 201 301
Tel: 0120 - 4170200 / 2581029 / 2586300
Fax: 0120 - 2581017 / 4170200
E-mail: [email protected]
Website: www.interarchbuildings.com
Mumbai
Kolkata
ChennaiBangalore
Hyderabad
Pune
Ahmedabad
NOIDAGreater NOIDA
Pantnagar
Central Marketing Office
Regional Office
Manufacturing Unit
NNOVATE NITIATE NTEGRATE
Support Network, India
Bhopal
Indore
Chandigarh
NNOVATE NITIATE NTEGRATE
15 16