BRK HYDRAULIC BRAKE - METAL WORK HYDRAULIC BRAKE.pdf · BRK HYDRAULIC BRAKE This is a closed-loop...
Transcript of BRK HYDRAULIC BRAKE - METAL WORK HYDRAULIC BRAKE.pdf · BRK HYDRAULIC BRAKE This is a closed-loop...
1-230
ACT
UA
TORS
BRK HYDRAULIC BRAKE
This is a closed-loop hydraulic brake without its own power source. It is normally associated with an ISO 15552 pneumatic cylinder. It consists of an oil-filled cylinder, one or more regulation valves and a tank compensating for oil leaks. It is available in two versions:• with regulation in piston rod extension, in retraction or both• SKIP valve (slow/fast) or STOP valve or both, with NC or NO controlAfter a certain operating time, the brake compensation tank needs to be topped up. Refer to the minimum mark on the dipstick. With the piston rod fully extended, the dipstick must project at least 15 mm from the tank cap. Use only COMLUBE DEXRON ATF hydraulic oil. During the first few work cycles, excess oil is ejected through a hole in the tank.
TECHNICAL DATA
COMPONENTS
Operating temperature °CFluid
Adjustable load NSpeed mm/minStandard strokes mm
Versions
Cylinder couplingConnectable cylinders mm
NBR
From –10 to +70Lubricated or unlubricated filtered air.
Lubrication, if used, must be continuous7000
10 to 600050, 100, 150, 200, 250, 300, 350, 400, 450, 500
special strokes up to 1000 on request.Regulation in piston rod extension and/or retraction. SKIP valves. STOP valves.
Tank in-line or on the side.Flange kit
ISO 15552 cylinders with bore Ø 40 to Ø 100
a PISTON ROD: thick chromed steelb HEADS: anodised aluminium alloyc PISTON ROD GASKET: NBR rubberd PISTON ROD GUIDE BUSHING: steel strip with bronze and PTFE inserte JACKET: drawn anodised aluminium alloyf PISTON: aluminium alloyg PISTON GASKET: NBR rubberh OIL SEAL GASKET: polyurethanei Static O-rings: NBR rubberj SEALING DISK: plastick SPRINGS: zinc-plated steell SECURING/ASSEMBLY SCREW: self-threading screw (Tap Tite)m OIL LEVEL STICK: zinc-plated steeln OIL RECOVERY TANKo VALVE for OIL FILLINGp FLOW REGULATION NEEDLEq MINIMUM LEVEL
BRK
HYDR
AUL
IC B
RAKE
1-231
ACT
UA
TORS
BRK
HYDR
AUL
IC B
RAKE
SKIP-STOP APPLICATION WITH VALVES
In normally-open (NO) valves, flow moves freely from A to D. When port C is supplied, this operates the SKIP valve and the fluid is forced through the bottleneck generated by the adjusting pin. When port B is supplied, this operates the STOP valve and interrupts the flow of fluid. In normally-closed NC valves, flow is normally inhibited. When port B is supplied, the fluid flows through but it is forced through the bottleneck generated by the adjusting pin. When port C is supplied, flow moves freely from A to D.
DIMENSIONS AND ORDERING CODES
Symbol Code Description W170001____ Hydraulic brake with regulation
in piston rod extension
____ = Enter the strokeWeight for stroke 0 mm = 1340 gWeight each mm = 4.2 g
HYDRAULIC BRAKE WITH REGULATION IN PISTON ROD EXTENSION
Symbol Code Description W170001____L Hydraulic brake with regulation
in piston rod extension, in-linetank
____ = Enter the strokeWeight for stroke 0 mm = 1300 gWeight each mm = 4.2 g
HYDRAULIC BRAKE WITH REGULATION IN PISTON ROD EXTENSION, IN-LINE TANK
Air inlet Air inlet
STOP SKIPNO
Stroke B U max1÷50 109 2351÷150 129 39151÷250 154 55251÷350 174 71351÷450 204 87451÷500 229 95
Stroke B U max1÷50 92 2351÷150 112 39151÷250 137 55251÷350 157 71351÷450 187 87451÷500 212 95
Air inlet Air inlet
STOP SKIPNC
+ = ADD THE STROKE
+ = ADD THE STROKE
1-232
ACT
UA
TORS
BRK
HYDR
AUL
IC B
RAKE
Symbol Code Description W170021____ Hydraulic brake with regulation
in piston rod extension/retraction
____ = Enter the strokeWeight for stroke 0 mm = 1710 gWeight each mm = 4.2 g
HYDRAULIC BRAKE WITH REGULATION IN PISTON ROD EXTENSION/RETRACTION
Symbol Code Description W170101____ Hydraulic brake with regulation
in extension + NO SKIP valve
W170201____ Hydraulic brake with regulation in extension + NO STOP valve
W170102____ Hydraulic brake with regulation in extension + NC SKIP valve
W170202____ Hydraulic brake with regulation in extension + NC STOP valve
____ = Enter the strokeWeight for stroke 0 mm = 1555 gWeight each mm = 4.2 g
HYDRAULIC BRAKE WITH REGULATION IN EXTENSION + SKIP VALVEHYDRAULIC BRAKE WITH REGULATION IN EXTENSION + STOP VALVE
Symbol Code Description W170011____ Hydraulic brake with regulation
in piston rod retraction
____ = Enter the strokeWeight for stroke 0 mm = 1340 gWeight each mm = 4.2 g
HYDRAULIC BRAKE WITH REGULATION IN PISTON ROD RETRACTION
Stroke B U max1÷50 98 2351÷150 118 39151÷250 143 55251÷350 163 71351÷450 193 87451÷500 218 95
Stroke B U max1÷50 109 2351÷150 129 39151÷250 154 55251÷350 174 71351÷450 204 87451÷500 229 95
Stroke B U max1÷50 109 2351÷150 129 39151÷250 154 55251÷350 174 71351÷450 204 87451÷500 229 95
+ = ADD THE STROKE
+ = ADD THE STROKE
+ = ADD THE STROKE
1-233
ACT
UA
TORS
BRK
HYDR
AUL
IC B
RAKE
Symbol Code Description W170111____ Hydraulic brake with regulation
in retraction + NO SKIP valve
W170211____ Hydraulic brake with regulation in retraction + NO STOP valve
W170112____ Hydraulic brake with regulation in retraction + NC SKIP valve
W170212____ Hydraulic brake with regulation in retraction + NC STOP valve
____ = Enter the strokeWeight for stroke 0 mm = 1555 gWeight each mm = 4.2 g
HYDRAULIC BRAKE WITH REGULATION IN RETRACTION + SKIP VALVEHYDRAULIC BRAKE WITH REGULATION IN RETRACTION + STOP VALVE
Symbol Code Description W170301____ Hydraulic brake with regulation
in extension + NO SKIP/STOPvalves
W170302____ Hydraulic brake with regulation in extension + NC SKIP/STOPvalves
____ = Enter the strokeWeight for stroke 0 mm = 1730 gWeight each mm = 4.2 g
HYDRAULIC BRAKE WITH REGULATION IN EXTENSION + SKIP/STOP VALVES
Symbol Code Description W170101____L Hydraulic brake with regulation
in extension + NO SKIP valve,in-line tank
W170201____L Hydraulic brake with regulation in extension + NO STOP valve,in-line tank
W170102____L Hydraulic brake with regulation in extension + NC SKIP valve,in-line tank
W170202____L Hydraulic brake with regulation in extension + NC STOP valve,in-line tank
____ = Enter the strokeWeight for stroke 0 mm = 1510 gWeight each mm = 4.2 g
HYDRAULIC BRAKE WITH REGULATION IN EXTENSION + SKIP VALVE, IN-LINE TANKHYDRAULIC BRAKE WITH REGULATION IN EXTENSION + STOP VALVE, IN-LINE TANK
Stroke B U max1÷50 109 2351÷150 129 39151÷250 154 55251÷350 174 71351÷450 204 87451÷500 229 95
Stroke B U max1÷50 109 2351÷150 129 39151÷250 154 55251÷350 174 71351÷450 204 87451÷500 229 95
Stroke B U max1÷50 92 2351÷150 112 39151÷250 137 55251÷350 157 71351÷450 187 87451÷500 212 95
+ = ADD THE STROKE
+ = ADD THE STROKE
+ = ADD THE STROKE
1-234
ACT
UA
TORS
BRK
HYDR
AUL
IC B
RAKE
Symbol Code Description W170311____ Hydraulic brake with regulation
in retraction + NO SKIP/STOPvalves
W170312____ Hydraulic brake with regulation in retraction + NC SKIP/STOPvalves
____ = Enter the strokeWeight for stroke 0 mm = 1730 gWeight each mm = 4.2 g
HYDRAULIC BRAKE WITH REGULATION IN RETRACTION + SKIP/STOP VALVES
Symbol Code Description W170301____L Hydraulic brake with regulation
in extension + NO SKIP/STOPvalves, in-line tank
W170302____L Hydraulic brake with regulation in extension + NC SKIP/STOPvalves, in-line tank
____ = Enter the strokeWeight for stroke 0 mm = 1690 gWeight each mm = 4.2 g
HYDRAULIC BRAKE WITH REGULATION IN EXTENSION + SKIP/STOP VALVES, IN-LINE TANK
Stroke B U max1÷50 109 2351÷150 129 39151÷250 154 55251÷350 174 71351÷450 204 87451÷500 229 95
Stroke B U max1÷50 92 2351÷150 112 39151÷250 137 55251÷350 157 71351÷450 187 87451÷500 212 95
+ = ADD THE STROKE
+ = ADD THE STROKE
Symbol Code Description W17002A____ Hydraulic brake with regulation
in extension/retraction + extension NO SKIP valve
W17002B____ Hydraulic brake with regulation in extension/retraction+ extension NC SKIP valve
____ = Enter the strokeWeight for stroke 0 mm = 1850 gWeight each mm = 4.2 g
HYDRAULIC BRAKE WITH REGULATION IN EXTENSION/RETRACTION + EXTENSION SKIP VALVE
+ = ADD THE STROKE
Stroke B U max1÷50 98 2351÷150 118 39151÷250 143 55251÷350 163 71351÷450 193 87451÷500 218 95
1-235
ACT
UA
TORS
BRK
HYDR
AUL
IC B
RAKE
Symbol Code Description W170023____ Hydraulic brake with regulation
in extension/retraction + extension NO STOP valve
W170024____ Hydraulic brake with regulation in extension/retraction+ extension NC STOP valve
____ = Enter the strokeNote: minimum stroke 100 mmWeight for stroke 0 mm = 1990 gWeight each mm = 4.2 g
HYDRAULIC BRAKE WITH REGULATION IN EXTENSION/RETRACTION + EXTENSION STOP VALVE
Symbol Code Description W170025____ Hydraulic brake with regulation
in extension/retraction+ retraction NO STOP valve
W170026____ Hydraulic brake with regulation in extension/retraction + retraction NC STOP valve
____ = Enter the strokeNote: minimum stroke 100 mmWeight for stroke 0 mm = 2080 gWeight each mm = 4.2 g
HYDRAULIC BRAKE WITH REGULATION IN EXTENSION/RETRACTION + RETRACTION STOP VALVE
Stroke B U max100÷150 118 39151÷250 143 55251÷350 163 71351÷450 193 87451÷500 218 95
Stroke B U max100÷150 118 39151÷250 143 55251÷350 163 71351÷450 193 87451÷500 218 95
+ = ADD THE STROKE
+ = ADD THE STROKE
Symbol Code Description W17002C____ Hydraulic brake with regulation
in extension/retraction+ retraction NO SKIP valve
W17002D____ Hydraulic brake with regulation in extension/retraction + retraction NC SKIP valve
____ = Enter the strokeWeight for stroke 0 mm = 1850 gWeight each mm = 4.2 g
HYDRAULIC BRAKE WITH REGULATION IN EXTENSION/RETRACTION + RETRACTION SKIP VALVE
+ = ADD THE STROKE
Stroke B U max1÷50 98 2351÷150 118 39151÷250 143 55251÷350 163 71351÷450 193 87451÷500 218 95
1-236
ACT
UA
TORS
BRK
HYDR
AUL
IC B
RAKE
Symbol Code Description W170123____ Hydraulic brake with regulation
in extension/retraction + dualSKIP valve + piston rod extension NO STOP valve
W170124____ Hydraulic brake with regulation in extension/retraction + dual SKIP valve + piston rod extension NC STOP valve
____ = Enter the strokeNote: minimum stroke 100 mmWeight for stroke 0 mm = 2110 gWeight each mm = 4.2 g
HYDRAULIC BRAKE WITH REGULATION IN EXTENSION/RETRACTION + DUAL SKIP VALVE + PISTON ROD EXTENSION STOP VALVE
Stroke B U max100÷150 118 39151÷250 143 55251÷350 163 71351÷450 193 87451÷500 218 95
+ = ADD THE STROKE
Symbol Code Description W170221____ Hydraulic brake with regulation
in extension/retraction + dual NO STOP valve
W170222____ Hydraulic brake with regulation in extension/retraction + dual NC STOP valve
____ = Enter the strokeNote: minimum stroke 150 mmWeight for stroke 0 mm = 2260 gWeight each mm = 4.2 g
HYDRAULIC BRAKE WITH REGULATION IN EXTENSION/RETRACTION + DUAL STOP VALVE
Symbol Code Description W170121____ Hydraulic brake with regulation
in extension/retraction + dualNO SKIP valve
W170122____ Hydraulic brake with regulation in extension/retraction + dualNC SKIP valve
____= Enter the strokeWeight for stroke 0 mm = 1850 gWeight each mm = 4.2 g
HYDRAULIC BRAKE WITH REGULATION IN EXTENSION/RETRACTION + DUAL SKIP VALVE
Stroke B U max150 118 39151÷250 143 55251÷350 163 71351÷450 193 87451÷500 218 95
Stroke B U max1÷50 98 2351÷150 118 39151÷250 143 55251÷350 163 71351÷450 193 87451÷500 218 95
+ = ADD THE STROKE
+ = ADD THE STROKE
1-237
ACT
UA
TORS
BRK
HYDR
AUL
IC B
RAKE
KEY TO CODES
W 1 7 0 0 1 2 0300 LSTROKE
W170 BRK hydraulic brake
0 Regulation1 Regulation + SKIP2 Regulation + STOP3 Regulation + SKIP + STOP
0 Extension1 Retraction2 Extension and retraction
1 No valve or NO 2 NC
✱ 3 + NO STOP in extension✱ 4 + NC STOP in extension✱ 5 + NO STOP in retraction✱ 6 + NC STOP in retraction ▲ A + NO SKIP in extension ▲ B + NC SKIP in extension ▲ C + NO SKIP in retraction ▲ D + NC SKIP in retraction
Enter the desired stroke in four digits (e.g. 0500 for stroke 500)
● L In-line tank, if present
● Only for versions with piston rod regulation in extension✱ In combination with regulation in extension/retraction or regulation + SKIP in extension/retraction▲ In combination with regulation in extension/retraction
Symbol Code Description W170125____ Hydraulic brake with regulation
in extension/retraction + dualSKIP valve + piston rod retraction NO STOP valve
W170126____ Hydraulic brake with regulation in extension/retraction + dualSKIP valve + piston rod retraction NC STOP valve
____ = Enter the strokeNote: minimum stroke 100 mmWeight for stroke 0 mm = 2210 gWeight each mm = 4.2 g
HYDRAULIC BRAKE WITH REGULATION IN EXTENSION/RETRACTION + DUAL SKIP VALVE + PISTON ROD RETRACTION STOP VALVE
Symbol Code Description W170321____ Hydraulic brake with regulation
in extension/retraction + dualSKIP valve + dual NO STOP valve
W170322____ Hydraulic brake with regulation in extension/retraction + dualSKIP valve + dual NC STOP valve
____ = Enter the strokeNote: minimum stroke 150 mmWeight for stroke 0 mm = 2415 gWeight each mm = 4.2 g
HYDRAULIC BRAKE WITH REGULATION IN EXTENSION/RETRACTION + DUAL SKIP VALVE + DUAL STOP VALVE
Stroke B U max100÷150 118 39151÷250 143 55251÷350 163 71351÷450 193 87451÷500 218 95
Stroke B U max150 118 39151÷250 143 55251÷350 163 71351÷450 193 87451÷500 218 95
+ = ADD THE STROKE
+ = ADD THE STROKE
1-238
ACT
UA
TORS
ACC
ESSO
RIES
FO
R BR
K HY
DRA
ULIC
BRA
KE
ACCESSORIES
FLANGE FOR MOUNTING WITH ISO 15552 CYLINDER
Code Description Weight [g]W0950402111 Kit BRK-P/C-040 58W0950502111 Kit BRK-P/C-050 93W0950632111 Kit BRK-P/C-063 97W0950802111 Kit BRK-P/C-080-100 151
Note: code corresponds to 4 + 4 screws
Code Ø A B C D E F F1 G ØH ØH1 I ØL ØM N Weight [g]W0950402012 40 55 - 38 38 109 26.5 - 55 35 32 27.5 7 7 12 418W0950502012 50 65 55 46.5 38 121 32.5 32.5 61 40 32 27.5 7 9 12 540W0950632012 63 75 55 56.5 38 131 37.5 37.5 66 45 32 27.5 7 9 15 792W0950802012 80 95 55 72 38 151 47.5 47.5 76 45 32 27.5 7 11 15 1216W0951002012 100 112 55 89 38 168 56 56 84.5 55 32 27.5 7 11 15 1535
Note: 1 pc. per pack complete with 4+4 screws
NOTES
FLANGE SCREW KIT