BP KIA 1.8 LT
Transcript of BP KIA 1.8 LT
7/21/2019 BP KIA 1.8 LT
http://slidepdf.com/reader/full/bp-kia-18-lt 1/26
1999-2000 ENGINES
1.8L 4-Cylinder
ENGINE IDENTIFICATION
Engine can be identified by the eighth character of the Vehicle Identification Number (VIN) stamped onmetal plate located on left side of dash panel. The VIN is also stamped into passenger side of enginecompartment bulkhead.
ENGINE IDENTIFICATION CODE
ADJUSTMENTS
VALVE CLEARANCE ADJUSTMENT
Engine is equipped with Hydraulic Lash Adjusters (HLA). No adjustment is required.
TROUBLE SHOOTING
To trouble shoot engine mechanical components, see appropriate table in TROUBLE SHOOTING article inGENERAL INFORMATION.
REMOVAL & INSTALLATION
FUEL PRESSURE RELEASE
To release fuel pressure, remove rear seat cushion. Disconnect fuel pump connector. See Fig. 1 . Start and
run engine until it stalls. Turn ignition off. Connect fuel pump connector. Install rear seat cushion.
NOTE: For repair procedures not covered in this article, see ENGINE OVERHAULPROCEDURES article in GENERAL INFORMATION.
Application Code
1.8L DOHC 5
NOTE: For installation reference, label all electrical connectors, vacuum hoses, andfuel lines before removal. Also, place mating marks on engine hood andother major assemblies before removal.
CAUTION: When battery is disconnected, vehicle computer and memory systems
may lose memory data. Driveability problems may exist until computer systems have completed a relearn cycle. Obtain radio anti-theft codes,if necessary, before disconnecting battery.
CAUTION: Fuel system is under pressure. Release pressure before servicing fuelsystem components.
2000 Kia Sephia
1999-2000 ENGINES 1.8L 4-Cylinder
2000 Kia Sephia
1999-2000 ENGINES 1.8L 4-Cylinder
1234
viernes, 19 de octubre de 2012 06:43:43 a.m. Page 1 © 2005 Mitchell Repair Information Company, LLC.
1234
viernes, 19 de octubre de 2012 06:43:47 a.m. Page 1 © 2005 Mitchell Repair Information Company, LLC.
7/21/2019 BP KIA 1.8 LT
http://slidepdf.com/reader/full/bp-kia-18-lt 2/26
Fig. 1: Locating Fuel Pump Electrical ConnectorCourtesy of KIA MOTORS AMERICA, INC.
ENGINE
Removal
1. Disconnect battery cables. Remove battery cover, battery and battery tray. Drain engine coolant.Remove data link connector upward from mass air flow sensor bracket.
2. Disconnect intake air temperature sensor connector and mass air flow sensor connector. Disconnectair intake hose from throttle body. Disconnect ventilation hose. Remove air duct. Remove accelerator cable and cruise control cable, if equipped. Remove air cleaner assembly.
3. Disconnect brake vacuum hose and purge control vacuum hose from dynamic chamber. Removeupper and lower radiator hoses. Disconnect fuel hose from fuel injector rail. Remove heater hoses.Disconnect IAC and throttle position sensor connectors. Disconnect injector connectors. Disconnectelectric connectors and bracket, and reinstall engine hanger.
4. Disconnect terminal connectors from starter and generator. Remove right and left splash shields.Remove exhaust manifold heat shield and 3 power steering pump bracket bolts.
5. Remove A/C compressor bolts and A/C compressor mounting bracket bolts. Disconnect ground strapfrom top of transaxle. Remove No. 4 engine mounting nuts and bolt. Remove No. 4 engine mount.
6. On A/T models, disconnect input/turbine speed sensor connector. On M/T models, disconnect back-up light switch connector. On all models, disconnect vehicle speed sensor connector. On A/T models,remove "U" clip from selector cable at transaxle linkage. Remove nut and washer from transaxle
2000 Kia Sephia
1999-2000 ENGINES 1.8L 4-Cylinder
1234
viernes, 19 de octubre de 2012 06:43:43 a.m. Page 2 © 2005 Mitchell Repair Information Company, LLC.
7/21/2019 BP KIA 1.8 LT
http://slidepdf.com/reader/full/bp-kia-18-lt 3/26
linkage.
7. On M/T models, remove manual transaxle linkage and extension bar. Remove clutch release cylinder and pipe. On A/T models, disconnect transaxle range switch connector. Disconnect solenoid valveconnector. Disconnect ATF cooler hoses.
8. On all models, raise and support vehicle. Remove front wheel assembly. Disconnect front oxygensensor connector. Remove front exhaust pipe. Remove right and left tie rod ends from steeringknuckles by removing cotter pin and nut from each tie rod end. Remove stabilizer control link boltand nut from right and left stabilizer control links, and then remove stabilizer control link.
9. Remove pinch bolt and nut from right and left ball joints. Separate ball joints from control arms.Remove joint shaft support bracket from engine block. Pry axle shafts from transaxle.
10. Lower vehicle, and attach engine hoist for engine removal. Remove nuts from No. 2 engine mount-to-mounting member. Remove bolt from No. 3 engine mount. Remove No. 1 engine mount bolts. Liftengine and transaxle out as an assembly.
Installation
1. Install engine and transaxle into engine compartment as an assembly. Install No. 1 engine mount bolts. Install No. 3 engine mount bolt. Install No. 2 engine mount nuts. Install No. 4 engine mount.
2. Remove engine hoist. Install NEW clips on axle shaft. Push drive shaft and joint shaft into transaxlewith opening of clips pointing upward. Install joint shaft support bracket bolts. Install right and leftlower ball joints into spindle. Install pinch bolts. Install right and left stabilizer control links. Installfront exhaust pipe.
3. On A/T models, connect ATF cooler hoses. Connect solenoid valve connector. Connect automatictransaxle range switch connector. Install washer and nut at automatic transaxle linkage. On M/Tmodels, install clutch release cylinder and pipe. Install extension bar and manual transaxle linkage. On
all models, install "U" clip. On M/T models, connect back-up light switch connector and vehiclespeed sensor connector.
4. On all models, connect input turbine speed sensor connector. Connect ground strap to top of transaxle.Install A/C compressor mounting bracket. Install power steering pump bracket bolts. Install exhaustmanifold heat shield. Install right and left splash shields.
5. To complete removal procedure, reverse removal procedure. Tighten all bolts and nuts tospecification. See TORQUE SPECIFICATIONS .
INTAKE MANIFOLD
EXHAUST MANIFOLD
Removal & Installation
1. Disconnect oxygen sensor. Remove exhaust manifold heat shield. Disconnect exhaust pipe andsupport bracket from exhaust manifold. Remove exhaust manifold.
2. To install, reverse removal procedure. Ensure gasket mating surfaces are clean and flat. Install gasketto cylinder head. Install manifold and tighten manifold nuts/bolts evenly to specification, starting fromcenter bolt and alternating outward. Install NEW donut gasket between exhaust pipe and manifold.
See TORQUE SPECIFICATIONS .
NOTE: Removal and installation procedures are not available from manufacturer.
2000 Kia Sephia
1999-2000 ENGINES 1.8L 4-Cylinder
1234
viernes, 19 de octubre de 2012 06:43:43 a.m. Page 3 © 2005 Mitchell Repair Information Company, LLC.
7/21/2019 BP KIA 1.8 LT
http://slidepdf.com/reader/full/bp-kia-18-lt 4/26
CYLINDER HEAD
Removal
1. Disconnect negative battery cable. Release fuel pressure. See FUEL PRESSURE RELEASE . Drainengine coolant and oil. Remove PCV hose and ventilation hose. Remove accelerator cable and cruisecontrol cable, if equipped. Remove air intake hose and air inlet duct. Label and disconnect allnecessary electrical connectors, ground wires, vacuum hoses, coolant hoses and control cables.
2. Remove exhaust manifold heat shield. Remove exhaust manifold pipe. Remove coolant bypass pipe.Remove intake manifold support bracket. Remove hydraulic lash adjuster. See HYDRAULIC LASHADJUSTER . Loosen cylinder head bolts in 2-3 steps in sequence. See Fig. 2 . Remove cylinder head.
Fig. 2: Cylinder Head Bolt Removal SequenceCourtesy of KIA MOTORS AMERICA, INC.
Inspection
Carefully clean carbon and gasket material from all mating surfaces. Clean threads of cylinder head bolts.Use tap to clean threads in engine block. Check cylinder head for warpage and cracks. Resurface or replacehead if not within specification. Check valve train components. Replace or resurface components if notwithin specification. See CYLINDER HEAD and VALVES & VALVE SPRINGS tables under ENGINESPECIFICATIONS.
CAUTION: Rotate crankshaft in clockwise direction only.
2000 Kia Sephia
1999-2000 ENGINES 1.8L 4-Cylinder
1234
viernes, 19 de octubre de 2012 06:43:43 a.m. Page 4 © 2005 Mitchell Repair Information Company, LLC.
7/21/2019 BP KIA 1.8 LT
http://slidepdf.com/reader/full/bp-kia-18-lt 5/26
Installation
1. Install cylinder head gasket. Install cylinder head assembly and cylinder head bolts. Using 5-6 steps,tighten cylinder head bolts in specified sequence. See Fig. 3 . See TORQUE SPECIFICATIONS .
2. To complete installation, reverse removal procedure. Tighten bolts and nuts to specification. SeeTORQUE SPECIFICATIONS . Add all fluids as necessary. Operate engine until cooling fans cycle.Check ignition timing.
Fig. 3: Cylinder Head Bolt Tightening SequenceCourtesy of KIA MOTORS AMERICA, INC.
CRANKSHAFT FRONT SEAL
Removal & Installation
Remove oil pump. See OIL PUMP . Using screwdriver, remove oil seal. To install, reverse, removal procedure. Tighten bolts and nuts to specification. See TORQUE SPECIFICATIONS .
TIMING BELT
Removal
1. Disconnect negative battery cable. Remove all accessory drive belts. Remove water pump pulley.Remove crankshaft pulley and timing belt guide plate. Remove upper and lower timing belt covers.
2. Turn crankshaft so timing mark on timing belt pulley aligns with timing mark on engine. See Fig. 4 .Ensure "I" mark on intake camshaft pulley aligns with mark on cylinder head cover. Ensure "E" mark on exhaust camshaft pulley aligns with mark on cylinder head cover. See Fig. 5 .
2000 Kia Sephia
1999-2000 ENGINES 1.8L 4-Cylinder
1234
viernes, 19 de octubre de 2012 06:43:43 a.m. Page 5 © 2005 Mitchell Repair Information Company, LLC.
7/21/2019 BP KIA 1.8 LT
http://slidepdf.com/reader/full/bp-kia-18-lt 6/26
3. If timing belt is to be reused, mark direction of timing belt rotation before removal. Loosen timing belt
tensioner lock bolt. Move tensioner away from belt with spring fully extended. Tighten tensioner boltwhile belt tension is released. Remove timing belt.
4. Loosen tensioner pulley lock bolt. Remove tensioner pulley. Remove timing belt. Mark direction of timing belt rotation for proper reinstallation.
Inspection
Check timing belt for cracks, peeling, abrasion or other damage. Check tensioner bearing for looseness or roughness of rotation. Inspect tensioner spring for stretching. Replace parts as necessary.
Installation
1. Install tensioner pulley. Pull tensioner pulley to its farthest point, and tighten lock bolt. Ensure timing belt and engine marks align. See Fig. 4 . Ensure intake and exhaust camshaft sprocket marks align.See Fig. 5 .
2. Install timing belt onto crankshaft sprocket first, then idler pulley, exhaust camshaft sprocket, intakecamshaft sprocket, and tensioner pulley in order. See Fig. 6 . Ensure there is no looseness between
belt and pulleys and sprockets.
3. Loosen timing belt tensioner lock bolt, and allow spring to apply tension on belt. Tighten tensioner pulley lock bolt to specification. See TORQUE SPECIFICATIONS . Rotate crankshaft clockwise 2complete revolutions. Ensure timing marks align. If timing marks do not align, remove belt, realign alltiming marks, and repeat installation procedure.
4. Check timing belt deflection. Check timing belt deflection with 22 lbs. (10 kg) of pressure applied to belt. Timing belt deflection should be .36-.45" (9.1-11.4 mm). If timing belt deflection is not withinspecification, repeat procedure and/or replace timing belt tensioner spring. If timing belt deflection iswithin specification, reverse removal procedure to complete installation. Tighten bolts and nuts tospecification. See TORQUE SPECIFICATIONS .
NOTE: DO NOT move camshaft or crankshaft once timing marks have beencorrectly positioned.
2000 Kia Sephia
1999-2000 ENGINES 1.8L 4-Cylinder
1234
viernes, 19 de octubre de 2012 06:43:43 a.m. Page 6 © 2005 Mitchell Repair Information Company, LLC.
7/21/2019 BP KIA 1.8 LT
http://slidepdf.com/reader/full/bp-kia-18-lt 7/26
Fig. 4: Aligning Crankshaft Timing Marks
Courtesy of KIA MOTORS AMERICA, INC.
2000 Kia Sephia
1999-2000 ENGINES 1.8L 4-Cylinder
1234
viernes, 19 de octubre de 2012 06:43:43 a.m. Page 7 © 2005 Mitchell Repair Information Company, LLC.
7/21/2019 BP KIA 1.8 LT
http://slidepdf.com/reader/full/bp-kia-18-lt 8/26
Fig. 5: Identifying Camshaft Sprocket Timing Marks
2000 Kia Sephia
1999-2000 ENGINES 1.8L 4-Cylinder
1234
viernes, 19 de octubre de 2012 06:43:43 a.m. Page 8 © 2005 Mitchell Repair Information Company, LLC.
7/21/2019 BP KIA 1.8 LT
http://slidepdf.com/reader/full/bp-kia-18-lt 9/26
Fig. 6: Installing Timing BeltCourtesy of KIA MOTORS AMERICA, INC.
HYDRAULIC LASH ADJUSTER
2000 Kia Sephia
1999-2000 ENGINES 1.8L 4-Cylinder
1234
viernes, 19 de octubre de 2012 06:43:43 a.m. Page 9 © 2005 Mitchell Repair Information Company, LLC.
7/21/2019 BP KIA 1.8 LT
http://slidepdf.com/reader/full/bp-kia-18-lt 10/26
Removal
1. Disconnect negative battery cable. Remove center cover. Remove ignition coils and spark plug wires.Disconnect PCV hose and ventilation hose. Remove timing belt. See TIMING BELT .
2. Remove cylinder head cover. Align camshaft and crankshaft timing belt alignment marks. See Fig. 4and Fig. 5 .
3. Remove phase sensor. Remove camshaft sprockets. Loosen camshaft bearing caps bolts in 5 or 6 stepsin sequence. See Fig. 7 . Remove camshafts. Reference mark HLAs to identify their original positionif they will be reused.
Inspection
Inspect face of HLA for wear or damage, replace as necessary.
Installation
1. Apply engine oil to friction surfaces of HLA. Install HLA in bores of cylinder head. Ensure HLAmoves smoothly in cylinder head bore. Apply engine oil to camshaft and camshaft bearing surfaces.Install camshaft so camshaft dowel pins point straight up. Install camshaft bearing caps according tocap number, with directional arrows pointing forward. Install bolts to camshaft bearing caps, andtighten in 5 or 6 steps in sequence. See Fig. 7
2. Apply engine oil to lip of NEW camshaft seal. Seat camshaft seal by hand, and tap seal into placeuntil flush with edge of camshaft bearing cap. Install camshaft pulleys onto camshaft aligning "I"mark with intake camshaft dowel pin and "E" mark with exhaust camshaft dowel pin. See Fig. 5 .
3. To complete installation, reverse removal procedure. Tighten bolts and nuts to specification. SeeTORQUE SPECIFICATIONS .
NOTE: Install Hydraulic Lash Adjusters (HLA) in original locations. Failure toinstall HLAs in their original location will result in premature anduneven wear of HLAs and camshafts. Remove HLAs from cylinder head. Place HLAs upside down in an oil-filled container.
2000 Kia Sephia
1999-2000 ENGINES 1.8L 4-Cylinder
1234
viernes, 19 de octubre de 2012 06:43:43 a.m. Page 10 © 2005 Mitchell Repair Information Company, LLC.
7/21/2019 BP KIA 1.8 LT
http://slidepdf.com/reader/full/bp-kia-18-lt 11/26
Fig. 7: Camshaft Bearing Cap Bolt Removal/Installation SequenceCourtesy of KIA MOTORS AMERICA, INC.
CAMSHAFT
Removal
1. Disconnect negative battery cable. Remove center cover. Remove ignition coils and spark plug wires.Disconnect PCV hose and ventilation hose. Remove timing belt. See TIMING BELT
2. Remove cylinder head cover. Align camshaft and crankshaft timing belt alignment marks. See Fig. 4and Fig. 5 .
3. Remove phase sensor. Remove camshaft pulleys. Loosen camshaft bearing caps bolts in 5 or 6 steps
in sequence. See Fig. 7 . Remove camshafts.
Inspection
Check camshaft journals and bearings for wear. Check camshaft lobes for wear and damage. Check camshaft runout. See CAMSHAFT table under ENGINE SPECIFICATIONS. If any measurements are notwithin specification, replace camshaft and/or cylinder head.
Installation
1. Apply engine oil to camshaft and camshaft bearing surfaces. Install camshaft so camshaft dowel pins point straight up. Install camshaft bearing caps according to cap number, with directional arrows pointing forward. Install bolts to camshaft bearing caps, and tighten in 5 or 6 steps in sequence. SeeFig. 7
2000 Kia Sephia
1999-2000 ENGINES 1.8L 4-Cylinder
1234
viernes, 19 de octubre de 2012 06:43:43 a.m. Page 11 © 2005 Mitchell Repair Information Company, LLC.
7/21/2019 BP KIA 1.8 LT
http://slidepdf.com/reader/full/bp-kia-18-lt 12/26
2. Apply engine oil to lip of NEW camshaft seal. Seat camshaft seal by hand, and tap seal in place untilit's flush with edge of camshaft bearing cap. Install camshaft pulleys onto camshaft aligning "I" mark with intake camshaft dowel pin and "E" mark with exhaust camshaft dowel pin. See Fig. 5 .
3. To complete installation, reverse removal procedure. Tighten bolts and nuts to specification. See
TORQUE SPECIFICATIONS .
REAR CRANKSHAFT OIL SEAL
Removal
Disconnect negative battery cable. On M/T, remove transaxle and flywheel. See appropriate article inCLUTCHES. For A/T, remove transaxle and drive plate. See AUTOMATIC TRANSMISSION REMOVAL& INSTALLATION article in AUTOMATIC TRANSMISSION SERVICING. On all models, remove rear cover. Using seal remover, remove oil seal from rear cover.
Installation
To install, lubricate seal lip with light coat of oil. Tap seal in until it is flush or no more than 0.02" (0.50mm) below surface of cover. Install rear cover. On M/T install flywheel and manual transaxle. On A/Tmodels, install drive plate and automatic transaxle. On all models, to complete installation, reverse removal
procedure. Tighten bolts and nuts to specification. See TORQUE SPECIFICATIONS .
WATER PUMP
Removal
Disconnect negative battery cable. Drain coolant. Remove timing belt. See TIMING BELT . Remove water inlet pipe and gasket. Remove water pump bolts, and remove water pump. Remove gasket and clean gasketmating surface of engine block.
Installation
Ensure all gasket mating surfaces are clean. Install water pump gasket on water pump. Install water pump.Tighten bolts to specification. See TORQUE SPECIFICATIONS .
OIL PAN
Removal
Disconnect negative battery cable. Drain engine oil. Remove engine splash covers. Remove exhaust header pipe and support brackets from front exhaust system. Remove oil pan mounting bolts. Using screwdriver,remove oil pan. Remove oil strainer.
Installation
NOTE: Rear crankshaft oil seal can be removed without removing oil pan or crankshaft.
CAUTION: DO NOT force pry bar between engine block and oil pan contactsurfaces when removing oil pan.
2000 Kia Sephia
1999-2000 ENGINES 1.8L 4-Cylinder
1234
viernes, 19 de octubre de 2012 06:43:43 a.m. Page 12 © 2005 Mitchell Repair Information Company, LLC.
7/21/2019 BP KIA 1.8 LT
http://slidepdf.com/reader/full/bp-kia-18-lt 13/26
Install oil strainer. Apply continuous bead of silicone sealant to baffle plate along inside of bolt holes oncontact surfaces. Install oil pan. Install oil pan mounting bolts. Ensure appropriate bolt is installed. Tightento specification. See Fig. 8 To complete installation, reverse removal procedure. Tighten all bolts tospecification. See TORQUE SPECIFICATIONS . Fill engine with oil.
Fig. 8: Identifying Oil Pan Mounting Bolts
Courtesy of KIA MOTORS AMERICA, INC.
CAUTION: If reusing oil pan mounting bolts, ensure old sealant is completelyremoved from bolt threads. Failure to do so may cause bolt holes tocrack.
NOTE: Install oil pan within 5 minutes after silicone sealant is applied.
2000 Kia Sephia
1999-2000 ENGINES 1.8L 4-Cylinder
1234
viernes, 19 de octubre de 2012 06:43:43 a.m. Page 13 © 2005 Mitchell Repair Information Company, LLC.
7/21/2019 BP KIA 1.8 LT
http://slidepdf.com/reader/full/bp-kia-18-lt 14/26
OVERHAUL
CYLINDER HEAD
Cylinder Head
Ensure all mating surfaces are clean. Check cylinder head for warpage. Resurface cylinder head if warpageexceeds .004" (.10 mm). Check manifold contact surfaces for warpage. Resurface manifold surfaces or replace cylinder head if warpage exceeds .008" (.20 mm). Check cylinder head height. See CYLINDER HEAD table under ENGINE SPECIFICATIONS. If measurements are not as specified, replace cylinder head.
Valve Springs
Ensure valve spring free length and out-of-square are within specification. See VALVES & VALVE
SPRINGS table under ENGINE SPECIFICATIONS. Replace valve spring as necessary.
Valves
Check valve face angle, margin thickness and stem diameter. Service or replace valves if measurements arenot within specification. See VALVES & VALVE SPRINGS table under ENGINE SPECIFICATIONS.
Valve Guides
1. Check valve stem-to-valve guide oil clearance. Ensure valve guide inside diameter is withinspecification. See CYLINDER HEAD table under ENGINE SPECIFICATIONS.
2. Measure valve guide installed height. If installed height is not within specification, adjust or replacevalve guide or cylinder head as necessary. See CYLINDER HEAD table under ENGINESPECIFICATIONS.
Valve Seat
1. Service valve guide as needed before servicing valve seat. Valve seat replacement information is notavailable from manufacturer. Inspect valve seat for roughness, pitting, cracks and damage. Check valve seat angle and seat width.
2. Measure seat contact width on valve, and ensure seat contact position should be in center of valveface. Service seat if angle and width are not within specification. See CYLINDER HEAD table under
ENGINE SPECIFICATIONS. Measure valve installed height after servicing valve seat.
Valve Seat Correction Angles
1. Measure seat contact width on valve. See CYLINDER HEAD table under ENGINESPECIFICATIONS. Ensure valve/seat contact position is at center of valve face. If width and positionare not within specification, cut seats as necessary.
2. If seat contact position is too high, correct using 63-degree cutter and 45-degree cutter. Finish angleusing 45-degree stone until contact width is corrected.
3. If seat contact position is too low, correct using 0-degree and 45-degree cutter. Finish angle using 45-degree stone until contact width is corrected. Seat valve to seat using lapping compound.
Valve Stem Installed Height
2000 Kia Sephia
1999-2000 ENGINES 1.8L 4-Cylinder
1234
viernes, 19 de octubre de 2012 06:43:43 a.m. Page 14 © 2005 Mitchell Repair Information Company, LLC.
7/21/2019 BP KIA 1.8 LT
http://slidepdf.com/reader/full/bp-kia-18-lt 15/26
1. After servicing valves, measure valve stem installed height. See VALVE INSTALLED HEIGHT
table. See Fig. 9 . If installed valve height is within standard specification, no adjustment is necessary.
2. If installed valve height exceeds standard specification but does not exceed service limit specification,install adjusting shim on spring seat to bring installed height back within standard specification.
3. If valve stem installed height exceeds specification, replace valve. If valve stem installed height stillexceeds limit, replace cylinder head. See VALVE INSTALLED HEIGHT table.
Fig. 9: Measuring Valve Stem Installed Height (Typical)
Courtesy of KIA MOTORS AMERICA, INC.
VALVE INSTALLED HEIGHT
Application In. (mm)
Intake
Standard 1.432-1.467 (36.37-37.26)
Service Limit (1) 1.467-1.495 (36.37-37.97)
Beyond Limit (2) 1.495 (36.37)
Exhaust
Standard 1.431-1.467 (36.35-37.26)Service Limit (1) 1.467-1.494 (36.37-37.95)
2000 Kia Sephia
1999-2000 ENGINES 1.8L 4-Cylinder
1234
viernes, 19 de octubre de 2012 06:43:43 a.m. Page 15 © 2005 Mitchell Repair Information Company, LLC.
7/21/2019 BP KIA 1.8 LT
http://slidepdf.com/reader/full/bp-kia-18-lt 16/26
CYLINDER BLOCK ASSEMBLY
Piston & Connecting Rod Assembly
1. Before removing rod cap from crankshaft, measure and record rod side play. See CONNECTINGRODS table under ENGINE SPECIFICATIONS. Before removal, ensure all rods, pistons and capsare marked for reassembly reference.
2. Before removing rod and piston assembly from block, check and record rod bearing oil clearance. SeeCRANKSHAFT, MAIN & CONNECTING ROD BEARINGS table under ENGINESPECIFICATIONS.
Piston Pin Replacement
1. Match mark piston pin and rod piston for reassembly reference. Using arbor press and piston pinremoval/installation set, press piston pin through rod and out of piston.
2. Check piston-to-pin clearance, and rod-to-pin interference fit. See PISTONS, PINS & RINGS tableunder ENGINE SPECIFICATIONS. Ensure piston mark and rod identification mark are in proper
position. Press pin into piston and rod until pin is centered. Piston should pivot freely.
Fitting Pistons
1. Check piston-to-cylinder wall clearance in 3 different vertical levels of piston travel. If clearance isnot within specification, rebore cylinders to fit oversize pistons.
2. Using NEW piston ring, measure piston ring side clearance around entire piston circumference. If clearance is not within specification, replace piston. See PISTONS, PINS & RINGS table under ENGINE SPECIFICATIONS.
Piston Rings
Insert NEW piston ring into cylinder, and measure ring end gap. Grind ring ends or replace piston ring if ring end gap is not within specification. See PISTONS, PINS & RINGS table under ENGINESPECIFICATIONS.
Connecting Rod Bearings
Check crankshaft connecting rod journals for wear, out-of-round, taper and undersize. Machine or replacecrankshaft and/or bearings as necessary. See CRANKSHAFT, MAIN & CONNECTING ROD
BEARINGS table under ENGINE SPECIFICATIONS.
Crankshaft & Main Bearings
1. Before removing main caps, measure and record crankshaft end play. Using Plastigage, measure and
Beyond Limit (2) 1.494 (37.95)
(1) If installed height exceeds specification, adjust with washer on spring seat area of cylinder head.
(2) If installed height exceeds specification, replace cylinder head.
NOTE: During disassembly, match mark components for reassembly reference.
2000 Kia Sephia
1999-2000 ENGINES 1.8L 4-Cylinder
1234
viernes, 19 de octubre de 2012 06:43:43 a.m. Page 16 © 2005 Mitchell Repair Information Company, LLC.
7/21/2019 BP KIA 1.8 LT
http://slidepdf.com/reader/full/bp-kia-18-lt 17/26
record main bearing oil clearance. DO NOT rotate crankshaft when measuring oil clearances.
2. Remove crankshaft. Measure and record each main journal diameter in 2 places. SeeCRANKSHAFT, MAIN & CONNECTING ROD BEARINGS table under ENGINESPECIFICATIONS. Machine or replace crankshaft as necessary. Main bearing upper halves are
grooved.3. Install main bearing caps in original positions. Tighten bearing cap bolts in sequence and to
specification. See Fig. 10 . See TORQUE SPECIFICATIONS .
Fig. 10: Main Bearing Cap Bolt Tightening SequenceCourtesy of KIA MOTORS AMERICA, INC.
Thrust Bearings
1. Check crankshaft end play with crankshaft bearings and caps installed, but without connecting rodsattached to crankshaft.
2. Replace thrust bearing if end play is not within specification. See CRANKSHAFT, MAIN &CONNECTING ROD BEARINGS table under ENGINE SPECIFICATIONS. Ensure thrust
bearings are installed with oil groove facing crankshaft. Oversize thrust bearings are available.
Cylinder Block
Check cylinder bore out-of-round, taper, and piston-to-cylinder bore clearance. Check head gasket surface
for warpage. If warpage is not within specification, machine or replace cylinder block as necessary. SeeCYLINDER BLOCK table under ENGINE SPECIFICATIONS.
2000 Kia Sephia
1999-2000 ENGINES 1.8L 4-Cylinder
1234
viernes, 19 de octubre de 2012 06:43:43 a.m. Page 17 © 2005 Mitchell Repair Information Company, LLC.
7/21/2019 BP KIA 1.8 LT
http://slidepdf.com/reader/full/bp-kia-18-lt 18/26
ENGINE OILING
ENGINE LUBRICATION SYSTEM
Oil pressure is provided by a rotor-type pump driven by crankshaft. Pump draws oil from oil pan through oilstrainer. From oil pump, oil is sent through oil filter to cylinder block and up to cylinder head. Oil thendrains back to oil pan. See Fig. 11 .
Crankcase Capacity
Crankcase capacity is 3.8 qts. (3.6L) without oil filter change, and 4.0 qts. (3.8L) with oil filter change.
Oil Pressure
With engine at operating temperature, oil pressure should be 43-57 psi (3.0-4.0 kg/cm2 ) at 3000 RPM.
Oil Pressure Relief Valve
Pressure relief valve is located in oil pump body and is not adjustable.
2000 Kia Sephia
1999-2000 ENGINES 1.8L 4-Cylinder
1234
viernes, 19 de octubre de 2012 06:43:43 a.m. Page 18 © 2005 Mitchell Repair Information Company, LLC.
7/21/2019 BP KIA 1.8 LT
http://slidepdf.com/reader/full/bp-kia-18-lt 19/26
Fig. 11: Cross-Sectional View Of Engine Oil CircuitCourtesy of KIA MOTORS AMERICA, INC.
OIL PUMP
Removal
1. Disconnect negative battery cable. Drain engine oil. Remove timing belt. See TIMING BELT under REMOVAL & INSTALLATION. Remove oil pan and strainer. See OIL PAN under REMOVAL &INSTALLATION. Remove generator.
2. Remove A/C compressor and mounting bracket (if equipped) from engine block. Remove crankshaft
pulley lock bolt. Remove timing belt pulley. Remove oil pump mounting bolt. Remove oil pump.3. Remove front oil seal. Carefully clean all gaskets and sealant from mating surfaces without damaging
2000 Kia Sephia
1999-2000 ENGINES 1.8L 4-Cylinder
1234
viernes, 19 de octubre de 2012 06:43:43 a.m. Page 19 © 2005 Mitchell Repair Information Company, LLC.
7/21/2019 BP KIA 1.8 LT
http://slidepdf.com/reader/full/bp-kia-18-lt 20/26
sealing/mating surfaces. Remove all sealant from components and bolts. Check oil pump clearances.See OIL PUMP SPECIFICATIONS table. Replace oil pump as necessary.
Installation
1. Use NEW gaskets when installing oil pump and pick-up tube. Tighten oil pump bolts to specification.See TORQUE SPECIFICATIONS . Apply light oil coat of clean oil to oil seal lip, and tap oil sealinto oil pump body until it is flush with edge of pump body. DO NOT bottom seal in pump body.
2. To complete installation, reverse removal procedure. Tighten bolts and nuts to specification. SeeTORQUE SPECIFICATIONS . Check oil fluid level, and add if necessary.
OIL PUMP SPECIFICATIONS
TORQUE SPECIFICATIONS
TORQUE SPECIFICATIONS
Application Maximum Clearance - In. (mm)
Inner Gear Tip-To-Outer Gear Clearance .007 (.18)
Outer Gear-To-Pump Body Clearance .015 (.38)
Gear-To-Pump Body Side Clearance .0035 (.089)
Application Ft. Lbs. (N.m)
A/C Compressor Bracket Bolt
12-mm 14-18 (19-24)
14-mm 28-38 (38-51)
A/C Compressor Mounting Bolt 27-38 (37-51)Automatic Transaxle Linkage Nut/Washer 24-34 (32-46)
Battery Tray 10-12 (14-16)
Camshaft Bearing Cap Bolts (1) 13-20 (18-27)
Camshaft Pulley Bolts 36-45 (49-61)
Clutch Release Cylinder & Pipe (M/T) 14-19 (19-26)
Connecting Rod Nut 35-37 (47-50)
Coolant Bypass Pipe 66-86 (89-117)
Crankshaft Pulley Bolt 9-13 (12-17)
Crankshaft Sprocket Bolt 116-123 (157-167)
Cylinder Head Bolt (2) (3)
Step 1 36 (49)
Step 2 (4) Loosen Bolts InSequence
Step 3 29 (39)
Step 4 (5)
Step 5 Turn Additional 90-Degrees
Step 6 Turn Additional 90-
DegreesDynamic Damper Bolt 55-76 (74-103)
2000 Kia Sephia
1999-2000 ENGINES 1.8L 4-Cylinder
1234
viernes, 19 de octubre de 2012 06:43:43 a.m. Page 20 © 2005 Mitchell Repair Information Company, LLC.
7/21/2019 BP KIA 1.8 LT
http://slidepdf.com/reader/full/bp-kia-18-lt 21/26
Engine Ground Strap Bolts
At Engine 28-38 (38-51)
At Frame (6)
Engine Hanger 27-38 (37-51)
Engine Mount Bolts/Nuts
No. 1 (3 Bolts) 49-69 (67-93)
No. 2 (2 Nuts) 28-38 (38-51)
No. 3 (1 Bolt) 63-86 (85-117)
No. 4
Bolt (1) 47-66 (64-89)
Nut (3) 51-69 (68-93)
Exhaust Manifold Heat Shield Bolt 14-22 (19-30)
Exhaust Manifold-To-Head Bolt/Nut
Manifold-To-Head (9) 28-38 (38-51)Manifold-To-TWC Warmup Converter (5) 16-21 (22-28)
Extension Bar (M/T) 23-34 (31-46)
Front Exhaust Pipe
Pipe-To-TWC Warmup Converter Nuts 30-39 (40-53)
Converter Hanger Nuts 51-69 (69-94)
Clamp Nuts 15-20 (20-27)
Intake Manifold Support Bracket 27-38 (37-51)
Joint Shaft Support Bracket Bolts 32-46 (43-62)
Main Bearing Cap Bolt (2) (7)
Step 1 29 (39)
Step 2 (8)
Step 3 15 (20)
Step 4 (5)
Step 5 Turn Additional 90-Degrees
Step 6 Turn Additional 60-Degrees
Manual Transaxle Linkage (M/T) 12-17 (16-23)
Oil Pump Bolt 14-19 (19-26)Pinch Bolts 35-38 (47-51)
Power Steering Pump Mounting Bolt 28 (38)
Rear Seal Cover Bolts
Short Bolts (6) (6)
Long Bolts (2) 30-41 (40-55)
Splash Shield 10-12 (14-16)
Stabilizer Control Link Bolts 32-45 (43-61)
Starter Bolt 27-38 (37-52)
Tensioner Pulley Lock Bolt 28-41 (38-55)Thermostat Housing 14-19 (19-26)
2000 Kia Sephia
1999-2000 ENGINES 1.8L 4-Cylinder
1234
viernes, 19 de octubre de 2012 06:43:43 a.m. Page 21 © 2005 Mitchell Repair Information Company, LLC.
7/21/2019 BP KIA 1.8 LT
http://slidepdf.com/reader/full/bp-kia-18-lt 22/26
ENGINE SPECIFICATIONS
GENERAL SPECIFICATIONS
CRANKSHAFT, MAIN & CONNECTING ROD BEARINGS
Timing Belt Guide Plate Bolt 9-13 (12-17)
Valve Cover Bolts 6-9 (8-12)
Water Pump Bolt 14-19 (19-26)
Wheel Lug Nuts 65-87 (88-118)
INCH Lbs. (N.m)
Center Cover Bolt 44-80 (5-9)
Oil Pan Bolts
Except Bolt "E" 70-97 (8-11)
"E" (9)
Oil Pressure Switch 106-160 (12-18)
Oil Strainer Bolt 70-106 (8-12)
Timing Belt Cover Bolt 70-97 (8-11)
Water Pump Pulley Bolt 70-97 (8-11)
(1) Tighten bolts in proper sequence. See Fig. 7 .
(2) Tighten bolts in 5 or 6 steps.
(3) Tighten bolts in proper sequence. See Fig. 3 .
(4) See Fig. 2 .
(5) Mark bolts for rotational reference.
(6) Tighten bolts to 70-106 INCH lbs. (8-12 N.m)
(7) See Fig. 10 .
(8) Loosen bolts in reverse order shown. See Fig. 10 .(9) Tighten bolt to 28-38 ft. lbs. (38-51 N.m).
Application Specification
Displacement 109.4 Cu. In. (1.8L)
Bore 3.19" (81 mm)
Stroke 3.43" (87 mm)Compression Ratio 9.4:1
Fuel System SFI
Application In. (mm)
Crankshaft
End Play
Standard .0032-.0111 (.080-.282)
Service Limit (1)
Maximum Runout .00098 (.0249)
Main Journal Bearings
2000 Kia Sephia
1999-2000 ENGINES 1.8L 4-Cylinder
1234
viernes, 19 de octubre de 2012 06:43:43 a.m. Page 22 © 2005 Mitchell Repair Information Company, LLC.
7/21/2019 BP KIA 1.8 LT
http://slidepdf.com/reader/full/bp-kia-18-lt 23/26
CONNECTING RODS
PISTONS, PINS & RINGS
Journal Diameter (1)
Undersize 1 - .010 (.25) 2.1728 (55.189)
Undersize 2 - .020 (.50) 2.1826-2.1833 (55.438-55.456)
Undersize 3 - .030 (.75) 2.1924-2.1931 (55.687-55.705)
Journal Out-Of-Round & Taper (1)
Oil Clearance
Standard .00095-.00165 (.0241-.0419)
Service Limit (1)
Connecting Rod Bearings
Journal Diameter (1)
Oversize - 1 .010 (.25) .1034-.1053 (2.626-2.675)
Oversize - 2 .20 (.50) .1083-.1102 (2.751-2.799)
Oversize - 3 .30 (.75) .1132-.1151 (2.875-2.924)
Standard .0985-.1003 (2.502-2.548)
Journal Out-Of-Round & Taper (1)
Oil Clearance
Standard .0008-.0017 (.020-.0431)
Service Limit .004 (.10)
(1) Information is not available from manufacturer.
Application In. (mm)
Bore Diameter
Connecting Rod Bearing Bore (1)
Piston Pin Bore (1)
Center-To-Center Length (1)
Maximum Bend (1)
Side Play
Standard .0044-.0103 (.112-.262)
Service Limit .012 (.30)
(1) Information is not available from manufacturer.
Application In. (mm)
Pistons
2000 Kia Sephia
1999-2000 ENGINES 1.8L 4-Cylinder
1234
viernes, 19 de octubre de 2012 06:43:43 a.m. Page 23 © 2005 Mitchell Repair Information Company, LLC.
7/21/2019 BP KIA 1.8 LT
http://slidepdf.com/reader/full/bp-kia-18-lt 24/26
CYLINDER BLOCK
Clearance
Standard .0015-.0021 (.038-.053)
Service Limit (1)
Diameter 3.1872-3.1879 (80.955)
Pins
Diameter .7869-.7871 (19.987-19.992)
Piston Fit .0004-.0010 (.010-.025)
Rod Fit (1)
Rings
No. 1
End Gap
Standard .006-.011 (.15-.28)
Service Limit .039 (1.0)
Side Clearance
Standard .002-.003 (.051-.076)
Service Limit .039 (1.0)
No. 2
End Gap
Standard .012-.018 (.30-.46)
Service Limit .039 (1.0)
Side Clearance
Standard .001-.003 (.025-.076)
Service Limit .039 (1.0)
No. 3 (Oil)
End Gap
Standard .008-.027 (.20-.69)
Service Limit .039 (1.0)
(1) Information is not available from manufacturer
Application In. (mm)
Cylinder Bore
Standard Diameter 3.1892-3.1897(81.006-81.018)
Maximum Taper & Out-Of-Round .0007 (.018)
Deck Height
Standard (1)
Minimum (1)
Maximum Deck Warpage (2) .006 (.15)
(1) Information is not available from manufacturer.
(2)Replace cylinder block if material removed from deck is more than .004" (10 mm).
2000 Kia Sephia
1999-2000 ENGINES 1.8L 4-Cylinder
1234
viernes, 19 de octubre de 2012 06:43:43 a.m. Page 24 © 2005 Mitchell Repair Information Company, LLC.
7/21/2019 BP KIA 1.8 LT
http://slidepdf.com/reader/full/bp-kia-18-lt 25/26
VALVES & VALVE SPRINGS
Application Specification
Valves
Face Angle 45°
Head Diameter (1)
Minimum Margin
Intake .035" (0.9 mm)
Exhaust .039" (1.0 mm)
Minimum Refinish Length
Intake
Standard 4.052" (121.92 mm)
Minimum (1)
Exhaust
Standard 3.993" (101.42 mm)Minimum (1)
Stem Diameter
Intake .2350-.2356" (5.97-5.984mm)
Minimum (1)
Exhaust .2348-.2354" (5.964-5.979 mm)
Minimum (1)
Installed Height(2)
Intake
Standard 1.432-.1467 (36.37-37.26)
Service Limit (3) 1.467-1.495 (36.37-37.97)
Beyond Limit (4) 1.495 (36.37)
Exhaust
Standard 1.431-1.467 (36.53-37.26)
Service Limit (3) 1.467-1.494 (36.37-37.95)
Beyond Limit (4) 1.494 (37.95)
Out-Of-Square
Intake & Exhaust .0638" (1.621 mm)
(1) Information is not available from manufacturer.
(2) Valve height is measured from top of installed valve to spring seat.
(3) If installed height exceeds specification, adjust with washer on spring seat area of cylinder head.
(4) If installed height exceeds beyond limit specification, replace cylinder head.
2000 Kia Sephia
1999-2000 ENGINES 1.8L 4-Cylinder
1234
viernes, 19 de octubre de 2012 06:43:43 a.m. Page 25 © 2005 Mitchell Repair Information Company, LLC.
7/21/2019 BP KIA 1.8 LT
http://slidepdf.com/reader/full/bp-kia-18-lt 26/26
CYLINDER HEAD
CAMSHAFT
Application Specification
Cylinder Head Height 5.272-5.280" (133.91-134.11 mm)
Maximum Warpage .004" (.10 mm)
Valve Seats
Seat Angle 45°
Seat Width .078-1.059" (1.98-26.90 mm)
Valve Guides
Valve Guide I.D. .2367-.2374" (6.012-6.030 mm)
Valve Guide Installed Height
Intake .539-.563" (13.69-14.30 mm)
Exhaust .658-.681" (16.71-17.30 mm)
Valve Stem-To-Guide Oil Clearance
Intake .0010-.0023" (.025-.058 mm)Exhaust .0012-.0025" (.030-.064 mm)
Service Limit .008" (.20 mm)
Application In. (mm)
Bore Diameter
Journals No. 1-5 (1)
End Play .0003-.0004 (.008-.010)
Journal Diameter
Standard 1.0606-1.0616 (26.939-26.965)
Minimum 1.0594 (26.909)
Maximum Journal Out-Of-Round .002 (.05)
Maximum Journal Runout .0012 (.030)
Journal Oil Clearance .0014-.0031 (.036-.079)
Lobe Height
Intake
Standard 1.6415 (41.694)
Exhaust
Standard 1.7560 (42.238)
(1) Information is not available from manufacturer.
2000 Kia Sephia
1999-2000 ENGINES 1.8L 4-Cylinder
1234