boss OD-20(T)
Transcript of boss OD-20(T)
SERVICE NOTESIssued by RJA
Apr.2002 OD-20(T)
(T)
TABLE OF CONTENTS
SPECIFIC.ATIONS............................................................2LOCATION OF CONTROLS ..........................................4LOCATION OF CONTROLS PARTS LIST ...................5EXPLODED VIEW ............................................................6EXPLODED VIEW PARTS LIST .....................................9PARTS LIST......................................................................10CHECKING THE VERSION NUMBER.......................13
RESTORING THE FACTORY SETTINGS...................13TEST MODE.....................................................................13BLOCK DIAGRAM.........................................................16CIRCUIT BOARD(JACK)...............................................18CIRCUIT BOARD(PANEL) ...........................................19CIRCUIT DIAGRAM(JACK) .........................................20CIRCUIT DIAGRAM(PANEL)......................................22
Copyright © 2002 ROLAND CORPORATIONAll rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION.
Printed in Japan (0800) (NB)17058015E0
Apr.2002
SPECIFIC.ATIONSOD-20: Overdrive/Distortion
Nominal Input Level-20 dBu
Input Impedance1 MΩ
Nominal Output Level-20 dBu
Output Impedance1 kΩ
Recommended Load Impedance10 kΩ or greater
Dynamic Range102 dB (IHF-A typ.)
ControlsEFFECT ON/OFF Pedal
MANUAL/MEMORY Pedal
DRIVE Knob
BOTTOM Knob
TONE Knob
LEVEL Knob
ATTACK SHAPE Knob
HEAVY OCTAVE Knob
TYPE Knob
VARIATION Button
AMP CTRL (amp control) Button
MEMORY WRITE Button
MEMORY SELECT Button
IndicatorsPOWER Indicator (serves also as battery check indicator)
EFFECT ON/OFF Indicator
MANUAL Indicator
MEMORY Indicator
VARIATION Indicator
AMP CTRL (amp control) Indicator
MEMORY Number Indicator (1-4)
ConnectorsINPUT Jack
AMP CTRL (amp control) Jack
LINE OUT/PHONES Jack
OUTPUT Jack
AC Adaptor Jack (DC 9 V)
Power SupplyDC 9 V: Dry Battery (R6/LR6 (AA) type) x 6
AC Adaptor
Current Draw85 mA (9 V max.)
* Expected battery life under continuous use:
Carbon: 8 hours
Alkaline: 20 hours
These figures will vary depending on the actual conditions of use.
Dimensions173 (W) x 158 (D) x 57 (H) mm
6-13/16 (W) x 6-1/4 (D) x 2-1/4 (H) inches
Weight
1.1 kg / 2 lbs 7 oz (including batteries)
AccessoriesOwner’s Manual
English :G6017351
Japanese :G6017350
Leaflet (“USING THE UNIT SAFELY,” “IMPORTANT NOTES,” and “Information”):(********)
Dry battery (LR6 (AA) type) x 6:(********)
* We recommend that alkaline batteries be used when replacing the batteries.
OptionsAC Adaptor (PSA-series)
* 0 dBu = 0.775 Vrms
* In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice.
2
OD-20(T)
3
Apr.2002
LOCATION OF CONTROLSfig.front
fig.rear
1
2
3
6
7 9 10
5
8
11
12
13
14
15
1617
4
2 364 5 7
1 8
4
OD-20(T)
LOCATION OF CONTROLS PARTS LIST
[Front]
[Rear]
No. PART CODE PART NAME DESCRIPTION Q’TY1 H5029855 SCREW M4X8 HEXAGON BUTTON HEAD 42 G2477122 R-KNOB 5
F3279802 POTENTIOMETERNO CLICK 50KB RD901-40-125F-B54-00D 53 G247751001 VGA KEYTOP S BLACK WITH LENS 2
4 G2477122 R-KNOB 1F3279803 POTENTIOMETER 11 CLICKS 50KB RD901-40-125F-B54-11D 1
5 H5029851 PEDAL SHAFT 16 1502928100 LED (RED) L-34HDSL 37 G2187540 PEDAL L 18 G2017180 CASE 19 G2217171 LED PANEL 1
10 G2187541 PEDAL R 111 H5029852 SCREW 4M3 FEBZC HEXAGON SOCKET BUTTON HEAD 212 G2357116 PEDAL PLATE 62X53 213 F5029126 POWER LED L-113GDT 114 G247751301 VGA KEYTOP S WITHOUT LENS 2
15 1502928100 LED (RED) L-34HDSL 416 G2217170 PANEL 117 G2477122 R-KNOB 1
F3279819 POTENTIOMETER CENTER CLICK 50KB RD901-40-125F-B54-0CD 1
No. PART CODE PART NAME DESCRIPTION Q’TY1 13449150MF PHONE JACK (STEREO) HTJ-064-12D 32 G2537552 LABEL CAUTION 13 G2217172 REAR PANEL 14 G2017621 BATTERY COVER 15 G2017148 BOTTOM COVER 16 G2357118 BOTTOM FOOT 17 F3449415 ADAPTOR JACK KM02009AB 18 13449155MF PHONE JACK (MONO) HTJ-064-12I 1
5
Apr.2002
EXPLODED VIEWfig.expro1
33
32
26
24
c
k
21
b
d
23
25
b
e
f
6
OD-20(T)
fig.expro2
a
11
18
a
12
18
11
16
j
14
15
17
10
13
7
Apr.2002
fig.expro3
1
2
5
3i
4
g
hRIGHT SIDELEFT SIDE9
6
7
8
8
OD-20(T)
EXPLODED VIEW PARTS LIST
[Part]
[Screw]
No. PART CODE PART NAME DESCRIPTION Q’TY1 G2017180 CASE 12 G2357111 CUSHION R 23 H5029851 PEDAL SHAFT 24 2215770201 PEDAL GUIDE BUSH 215-702 25 2217710900 COIL SPRING 214-109 26 G2357116 PEDAL PLATE 62X53 27 G2357115 PEDAL FOOT M8 28 G2187541 PEDAL R 19 G2187540 PEDAL L 110 G2017148 BOTTOM COVER 111 G2357118 BOTTOM FOOT 212 G2017621 BATTERY COVER 113 G2017620 BATTERY CASE 114 G2177308 BATTERY TERMINAL(+) 115 G2177309 BATTERY TERMINAL(-) 116 G2177307 BATTERY TERMINAL(+-) 117 G2257130 BATTERY INSULATING SHEET 118 G2537552 LABEL CAUTION QUICK MANUAL 121 G2477122 R-KNOB 723 G2257129 INSULATING SHEET 124 G2217170 PANEL 125 G2217172 REAR PANEL 126 G2217171 LED PANEL 132 G247751301 VGA KEYTOP S WITHOUT LENS 233 G247751001 VGA KEYTOP S BLACK WITH LENS 2
No. PART CODE PART NAME DESCRIPTION Q’TYa H5029115 SCREW 3X8 PAN TAPTITE-2 FEBZC 7b H5019110 SCREW M3X6 PAN TAPTITE-2 FEZC 9c H5029855 SCREW M4X8 HEXAGON SOCKET BUTTON HEAD FENI 4d H5039205 WASHER 12.5X9.5X0.5/0.9 INTERNAL TOOTH FENI 4e H5039112 WASHER M9 4f H5039510 NUT M9X12X2 FENI 4g H5029852 SCREW 4M3 FEBZC HEXAGON SOCKET BUTTON HEAD 2h H5039413 NYLON WASHER M4.1X7.5X0.5 BLACK 2i H5039414 NYLON WASHER M5.1X9.5X0.5 BLACK 2j H5019430 SCREW M2.6X5 BINDING HEAD TAPTITE FEZC 2k H5039521 VR ACCESSORY NUT M7 7
9
Apr.2002
PARTS LISTfig.part1e
SAFETY PRECAUTIONS:The parts marked have safety-related characteristics. Use only listed parts for replacement.
CONSIDERATION ON PARTS ORDRINGWhen ordering any parts listed in the parts list, please specify the following items in the order sheet.
QTY PART NUMBER DESCRIPTION MODEL NUMBEREx. 10 22575241 Sharp Key C-20/50
15 2247017300 Knob (orange) DAC-15DFailure to completely fill the above items with correct number and description will result in delayed or even undelivered replacement.
NOTE: The parts marked # are new. (initial parts)
CASING G2357116 PEDAL PLATE 62X53 2 G2017620 BATTERY CASE 1 G2017621 BATTERY COVER 1 G2017148 BOTTOM COVER 1 G2357118 BOTTOM FOOT 2# G2017180 CASE 1# G2217171 LED PANEL 1# G2217170 PANEL 1# G2187541 PEDAL R 1# G2187540 PEDAL L 1
H5029851 PEDAL SHAFT 2# G2217172 REAR PANEL 1
“KNOB,BUTTON” G2477122 R-KNOB 7 G247751001 VGA KEYTOP S BLACK WITH LENS 2 G247751301 VGA KEYTOP S WITHOUT LENS 2
SWITCH 01780101 SKQKAB TACT SWITCH SW3, SW4, SW5, SW6 on PB 4 13129778 SKQKAH TACT SWITCH SW1, SW2 on PB 2
JACK,EXT TERMINAL 13449150MF HTJ-064-12D PHONE JACK (STEREO) JK1, JK2, JK3 on JB 3 13449155MF HTJ-064-12I PHONE JACK (MONO) JK4 on JB 1 F3449415 KM02009AB ADAPTOR JACK JK5 on JB 1
PWB ASSY# E 75D693P000 JACK PWB ASSY # 75D693M000 PANEL PWB ASSY
IC# 02897545 MN101C30AHD OD-20 VER1.00 IC(CPU 8BIT) IC6 on JB 1# F5209123 S-80930ALMP-DAT-T2 IC (REST) IC7 on JB 1 F5179604 CAT24WC02J IC (EEPROM) IC4 on JB 1 02565501 TC220CCA0AF-B01(MR3) IC (DSP) IC5 on JB 1# F5179125 S-8520E33MC-BJS-T2 IC (DC-DC) IC8 on JB 1 15289109 M5216FP-600D IC (BIPOLAR OP AMP) IC10, IC11 on JB 2 15189261 M5218AFP-600E IC (BIPOLAR OP AMP) IC3 on JB 1 00346445 NJM2100M(TE3) IC (BIPOLAR OP AMP) IC1 on JB 1 02451434 AK4552VT IC (AD/DA) IC2 on JB 1
TRANSISTOR 00679045 2SA1298-Y(TE85R) TRANSISTOR Q5 on JB 1 15309104 2SA1586-GR(TE85R) TRANSISTOR Q4 on JB 1 15319108 2SC-3324GR-TE85R TRANSISTOR Q3, Q12 on JB 2 00562012 2SC3265-Y(TE85R) TRANSISTOR Q7 on JB 1 15319107 2SC4116-GR(TE85R) TRANSISTOR Q6, Q9, Q10 on JB 3 F5139608 IRF7606 POWER MOS FET Q11 on JB 1# F5329530 2SK879Y FET TRANSISTOR Q2, Q8 on JB 2 15329103 2SK880GR-TE85R FET TRANSISTOR Q1 on JB 1
DIODE 02562878 02DZ5.1-Y(TPH3) ZENER DIODE D8 on JB 1 01019534 1SS355 TE-17 SWITCHING DIODE D1, D4, D6, D10 on JB 4 F5029126 L-113GDT POWER LED LED2 on PB 1
10
OD-20(T)
1502928100 L-34HDSL LED (RED) LED3, 4, 5, 8, 9, 10, 11 on PB 7 F5029117 L-312LRD LED LED6, 7 on PB 2 15339119 1SS-352 DIODE D2 on JB 1 00783034 1SS294(TE85L) DIODE D3 on JB 1 15339120 1SS302 DIODE DA3 on JB 1 F5339137 SS14 VF=0.45V DIODE D5, D7 on JB 2
DIODE
RESISTOR F5419707 CRN34101J RESISTOR ARRAY RA5,6 on JB 2# F5399951 68(1/2W) CHIP RESISTOR (1/2W) R64, R68 on JB 2# F2569127 MINISMDC075 POLY SWITCH R48 on JB 1 00566867 RPC05T 100 J MTL.FILM RESISTOR R37, R76, R77, R79 on JB 4 00567023 RPC05T 101 J MTL.FILM RESISTOR R51 on JB 1 00567156 RPC05T 102 J MTL.FILM RESISTOR R6, R61 on JB 2 00567289 RPC05T 103 J MTL.FILM RESISTOR R1, R7, R11, R12, R13, R14, R15, R17, R19, 25 00567412 RPC05T 104 J MTL.FILM RESISTOR R10, R28, R45, R67, R75, R78, R82, R83, R86 12 00567556 RPC05T 105 J MTL.FILM RESISTOR R2, R3, R5, R27, R29, R44, R60 on JB 7 00567290 RPC05T 123 J MTL.FILM RESISTOR R25, R34 on JB 12 00567301 RPC05T 153 J MTL.FILM RESISTOR R23, R36 on JB 2 00567190 RPC05T 222 J MTL.FILM RESISTOR R57 on JB 1 00567334 RPC05T 273 J MTL.FILM RESISTOR R59 on JB 1 00566934 RPC05T 330 J MTL.FILM RESISTOR R54 on JB 1 00567089 RPC05T 331 J MTL.FILM RESISTOR R62, R69, R82 on JB 3 00567367 RPC05T 393 J MTL.FILM RESISTOR R30 on JB 1 00567245 RPC05T 472 J MTL.FILM RESISTOR R9, R66, R88 on JB 3 00567378 RPC05T 473 J MTL.FILM RESISTOR R8, R16, R21, R26, R31, R41, R47, R52, R53, 11 00567501 RPC05T 474 J MTL.FILM RESISTOR R4, R74 on JB 2 00567134 RPC05T 681 J MTL.FILM RESISTOR R72 on JB 1# F3829270 27(2W) METAL OXIDE RESISTOR R18, 22 on JB 2 F5429365 10K OHM F RANK (1%) CHIP RESISTOR R24 on JB 1 F5429386 150K F (1608TYPE) CHIP RESISTOR R20 on JB 1# F5419740 CRN34473J CHIP ARRAY RESISTOR RA4 on JB 1# F5419741 CRN34681J CHIP ARRAY RESISTOR RA2,3 on JB 2
POTENTIOMETER# F3279819 RD901-40-125F-B54-0CD 50KB ROTARY POT. W/CENTER CLICK VR2 on PB 1 F3279802 RD901-40-125F-B54-00D POTENTIOMETERNO CLICK 50KB VR1, VR3, VR4, VR5, VR6 on PB 5 F3279803 RD901-40-125F-B54-11D POTENTIOMETER 11 CLICKS 50KB VR7 on PB 1
CAPACITOR 02341489 ECPU1C474MA5 MYLAR CAPACITOR(SUBMI-
CRON) 1
# F5349704 ECPU1C474MA5 MYLAR CAPACITOR (SUBMI-CRON)
C1 on JB 1
# F5359732 GRM39B102J50PT CHIP CAPACITOR (1608 TYPE) C80 on JB 1 F5359780 GRM39B103K50PT CHIP CAPACITOR (1608 TYPE) C55, C56, C57, C58, C59, C60, C61, C72 on J 8# F5359382 GRM39B182J50PT CHIP CAPACITOR (1608 TYPE) C89, C95 on JB 2 F5359740 GRM39B222K50PT CHIP CAPACITOR (1608 TYPE) C5, C9 on JB 2# F5359812 GRM39B473J50PT CHIP CAPACITOR (1608 TYPE) C17, C33 on JB 2# F5359372 GRM39B683J50PT CHIP CAPACITOR (1608 TYPE) C67 on JB 1 F5359720 GRM39CH101J50PT CHIP CAPACITOR (1608 TYPE) C6 on JB 1# F5359803 GRM39CH151J50PT CHIP CAPACITOR (1608 TYPE) C83, C85, C88, C90 on JB 4# F5359370 GRM39CH180J50PT CHIP CAPACITOR (1608 TYPE) C69 on JB 1 F5359704 GRM39CH220J50PT CHIP CAPACITOR (1608 TYPE) C68, C70, C71 on JB 3# F5359373 GRM39CH271J50PT CHIP CAPACITOR (1608 TYPE) C12, C13, C22 on JB 3 F5359800 GRM39F104Z25PT CHIP CAPACITOR (1608 TYPE) C11, C21, C24, C26, C30, C32, C35, C36, C37 30# F3629692 0.22/50V CAPACITOR C87 on JB 1# F3629695TS 1/50V CAPACITOR C2, C3, C19, C29, C91, C94 on JB 6# F3629678TS 10/16V CAPACITOR C4, C7, C8, C10, C14, C15, C16, C18, C20, C 14# 13629550KM 100/16V CAPACITOR C31, C49, C52, C54, C76, C78, C81, C86, C92 9# 13629509KM 47/16V CAPACITOR C34, C74 on JB 2
INDUCTOR,COIL,FILTER F2449216 SLF7045T-151MR40 SMD COIL L3 on JB 1 02563478 NFM4516P13C204F EMI FILTER C48 on JB 1 F2449210 SLF7032T-4R7M1R7-2(4.7UH) COIL L2 on JB 1
CRYSTAL,RESONATOR 02673278 CX-49G 11.2896MHZ CRYSTAL X2 on JB 1 F5299108 HC-49SM 8MHZ CRYSTAL X1 on JB 1
CONNECTOR F3439160 53015-0210 2P P=2MM CONNECTOR CN4 on JB 1 F3439165 A2001WR2-10P CONNECTOR CN1 on JB 1# F3439200 A2001WR2-15P CONNECTOR CN2 on JB 1
11
Apr.2002
WIRING,CABLE G3487163 WIRING BATTERY L=80MM 2P 1# G3467251 WIRING 15P L=52MM P=2MM CN2 on PB 1# G3487421 WIRING 10P L=40MM P=2MM CN1 on PB 1 G3477146 RIBBON CABLE 3P L=40X5X5 MM P=2MM CN3 on JB 1
SCREWS H5019110 SCREW M3X6 PAN TAPPING-2 FEZC 10 H5029115 SCREW 3X8 PAN TAPPING-2 FEBZC 7 H5039205 WASHER 12.5X9.5X0.5/0.9 INTERNAL TOOTH FENI 4 H5029852 SCREW 4M3 FEBZC HEXAGON SOCKET BUTTON HEAD 2# H5029855 SCREW M4X8 HEXAGON BUTTON HEAD 4 H5039510 NUT M9X12X2 FENI 4 H5039413 NYLON WASHER M4.1X7.5X0.5 BLACK 2 H5039414 NYLON WASHER M5.1X9.5X0.5 BLACK 2 H5019430 SCREW M2.6X5 BINDING HEAD TAPTITE FEZC 2 H5039521 VR ACCESSORY NUT M7 7 H5039112 WASHER M9 4
PACKING# G2627250 PACKING CASE 1 G2607212 PACKING CASE LOWER 1 G2237614 REAR PAD 1 G2237613 SIDE PAD 1
MISCELLANEOUS G2357115 PEDAL FOOT M8 2 H2369427 LED SPACER H=8MM 4 2215770201 PEDAL GUIDE BUSH 215-702 2 2217710900 COIL SPRING 214-109 2 G2257130 BATTERY INSULATING SHEET 1 G2177308 BATTERY TERMINAL(+) 1 G2177307 BATTERY TERMINAL(+-) 1 G2177309 BATTERY TERMINAL(-) 1 G2357111 CUSHION R 2 G2257129 INSULATING SHEET CENTER 1# G2537552 LABEL CAUTION 1 G2197126 LED GUIDE 1
ACCESSORIES (Standard)# G6017350 OWNER’S MANUAL JAPANESE 1# ******** ALKALINE BATTERY LR6SG-P2 3# G6017351 OWNER’S MANUAL ENGLISH 1
12
OD-20(T)
CHECKING THE VERSION NUMBERAfter you enter test mode, perform step 5.
1. Turn all knobs to MIN (all the way to the left).
2. While holding down the left pedal and the right pedal, insert the 9V plug into DC IN.
At this time, only the POWER LED will light.
3. Release the left and right pedals. The EFFECT ON/OFF LED will blink.
4. Within four seconds, press the left pedal and then the right pedal.
If you were successful in entering test mode, the EFFECT ON/OFF LED, MANUAL LED, and MEMORY LED will light.
5. Set the TYPE volume to METAL/LOUD.
. The version number will be indicated as follows.
For Ver1.00, only the MEMORY 2 LED will light.
(The integer portion is indicated by the MEMORY 1 and 2 LEDs
1: MEMORY 1 LED: dark MEMORY 2 LED: lit
2: MEMORY 1 LED: lit MEMORY 2 LED: dark
3: MEMORY 1 LED: lit MEMORY 2 LED: lit
The first decimal place is indicated by the MEMORY 3 and 4 LEDs
0: MEMORY 3 LED: dark MEMORY 4 LED: dark
1: MEMORY 3 LED: dark MEMORY 4 LED: lit
2: MEMORY 3 LED: lit MEMORY 4 LED: dark
3: MEMORY 3 LED: lit MEMORY 4 LED: lit
The second decimal place is indicated by the MANUAL LED and MEMORY LED
0: MANUAL LED: dark MEMORY LED: dark
1: MANUAL LED: dark MEMORY LED: lit
2: MANUAL LED: lit MEMORY LED: dark
3: MANUAL LED: lit MEMORY LED: lit )
RESTORING THE FACTORY SETTINGSReturning Settings to Their Factory Defaults
You can restore the memories (1-4), pedal mode settings, and the MEMORY Number Indication to their original factory values.
Memory Settings
Memory 1 LOUD
Memory 2 LEAD
Memory 3 OD-1
Memory 4 STACK
Pedal Mode
1 (MANUAL -> MEMORY 1 -> MEMORY 2 -> MEMORY 3 -> MEMORY 4 -> MANUAL)
MEMORY Number Indication
Lighting Pattern 1(Only the indicator for the selected memory lights up.)
Carrying out the following procedure completely clears the content currently stored in the memories (1-4).
1. Switch off the power.
Disconnect the connection plug from the INPUT jack.
2. While holding down the WRITE button, switch on the power.
Insert the connection plug into the INPUT jack.
When you release the button, the MEMORY Number indicators blink.
3. Press the MEMORY WRITE button.
After the MEMORY Number indicators begin blinking rapidly, the setting is stored in memory and the unit returns to its ordinary state.
* To cancel the setting change, operate the EFFECT ON/OFF pedal or the MANUAL/MEMORY pedal before pressing the MEMORY WRITE button. The unit will return to its ordinary state.
TEST MODE
Required items 1. Oscillator
2. Noise meter
3. Oscilloscope
4. Monitor amp (e.g., MA-12)
5. Guitar amp (with a channel-switching jack)
6. Stereo plug
7. 47kΩ short plug
1. How to enter test mode1. Turn all knobs to MIN (all the way to the left).
Connect a short plug (47kΩ) to INPUT.
2. While holding down the left pedal and right pedal, insert the 9V plug into DC IN.
At this time, only the POWER LED will light.
3. Release the left and right pedals. The EFFECT ON/OFF LED will blink.
4. Within four seconds, press the left pedal and then the right pedal.
If you were successful in entering test mode, the EFFECT ON/OFF LED, MANUAL LED, and MEMORY LED will light.
2. List of test items1. IC check
2. Switching noise / shock noise check
3. Residual noise check
4. SW and LED check
5. AMP control check
6. VR Check
7. DAC check (includes FET SW (EFFECT) inspection)
8. DSP thru check
9. Analog mute check (FET SW (DIRECT) inspection)
10. Version check
13
Apr.2002
3. Test contents1. IC check1. When you enter test mode, the DSP(IC5) and EEPROM(IC4) check will
begin automatically.
2. If no problem is found, the EFFECT ON/OFF LED, MANUAL LED, and MEMORY LED will light.
3. If a problem is found, the LEDs will indicate the problem as follows.
ON/OFF LED blinking: EEPROM error
MANUAL LED blinking: DSP(PRAM) error
MEMORY LED blinking: DSP(IRAM) error
If a problem is found, the unit will remain in this state, and it will not be possible to carry out the remaining tests.
2. Switching noise / shock noise check1. With the EFFECT ON/OFF LED, MANUAL LED, and MEMORY LED lit,
connect a short plug (47kΩ) to INPUT, and a monitor speaker to OUTPUT.
2. Press the EFFECT ON/OFF switch several times, and verify that no abnormal switching noise occurs.
3. Press the EFFECT ON/OFF switch to make the EFFECT ON/OFF LED go dark (ANALOG BYPASS), and drop the unit from a height of approximately 10 cm to subject it to physical shock. Verify that no abnormal noise occurs.
4. Press the EFFECT ON/OFF switch to make the EFFECT ON/OFF LED light (DSP THRU), and drop the unit from a height of approximately 10 cm to subject it to physical shock. Verify that no abnormal noise occurs.
3. Residual noise check1. Connect a noise meter to the OUTPUT.
2. Press the EFFECT ON/OFF switch to make the EFFECT ON/OFF LED light (DSP THRU), and measure the residual noise.
Verify that the value detected by the noise meter is below -73 dBm (IHF-A).
3. Press the EFFECT ON/OFF switch to make the EFFECT ON/OFF LED go dark (BYPASS), and measure the residual noise.
Verify that the value detected by the noise meter is below -104 dBm (IHF-A).
4. SW and LED check1. Press the VARIATION switch, and you will proceed to the switch and
LED check.
First verify that only the VARIATION LED is lit.
The other LEDs will be dark.
Press the switches in the following order, and verify that in a similar way, only one LED at a time is lit.
2. Press the AMP CTRL switch, and verify that only the AMP CTRL LED is lit.
3. Press the MEMORY WRITE switch, and verify that only the EFFECT ON/OFF LED is lit.
4. Press the MEMORY WRITE switch, and verify that only the MANUAL LED is lit.
5. Press the MEMORY WRITE switch, and verify that only the MEMORY LED is lit.
6. Press the MEMORY SELECT switch, and verify that only the MEMORY 1 LED is lit.
7. Press the MEMORY SELECT switch, and verify that only the MEMORY 2 LED is lit.
8. Press the MEMORY SELECT switch, and verify that only the MEMORY 3 LED is lit.
9. Press the MEMORY SELECT switch, and verify that only the MEMORY 4 LED is lit.
(It is not possible to proceed to other test items before you have finished the above procedure.)
5. AMP control check1. Connect the AMP CTRL jack to the channel switching jack of the guitar
amp.
2. Verify that the guitar amp channel is switched each time you press the AMP CTRL SW.
6. VR check1. Turn the DRIVE volume from MIN to MAX, and verify that the
MEMORY 1-4 LEDs are all dark when the volume is at MIN (the instant you begin turning the volume), and light correspondingly as you turn the volume, so that all LEDs are lit when you reach MAX.
(Each VR you operate here must be left at the MAX position so that you will be able to proceed to the next test item.)
In the same way, perform this test in the following order for the other VR’s.
2. BOTTOM volume
3. TONE volume
4. LEVEL volume
5. ATTACK SHAPE volume
6. HEAVY OCTAVE volume
7. With the TYPE volume turned all the way to the left, turn it toward the right one click at a time, and verify that the LEDs change as follows. (TABLE A)
dark lit
(TABLE A)
TYPE EFFECT MANUAL MEMORY VARI AMPCTRL MEM1 MEM2 MEM3 MEM40 (OD-2/OD-1)
1 (BD-2/DS-1)
2 (HM-2/MT-2)
3 (BOOST/LEAD)
4 (CRUNCH/STACK)
5 (METAL/LOUD)
6 (T-SCREAM/FULL-D)
7 (DST+/CENTA OD)
8 (GUV DS/P-RAT)
9 (R-MAN/MUFF FUZZ)
10 (FACE/OCT FUZZ)
14
OD-20(T)
7. DAC check1. Set the TYPE volume to BD-2/DS-1.
2. Connect an oscilloscope to OUTPUT, and check the output waveform (DSP oscillation).
fig.1
(200mV/div, 1msec)
3. Press MEMORY SELECT. The MEMORY 4 LED will go dark, and the output signal will be muted. Verify that the signal is less than -67 dBm (IHF-A).
4. Connect an oscilloscope to LINE OUT/PHONES, and check the L and R output waveform (DSP oscillation).
fig.2
(200mV/div, 1msec)
5. Press MEMORY SELECT. The MEMORY 4 LED go dark, and the output signal will be muted. Verify that the noise for L and R is less than -68 dBm (IHF-A).
8. DSP thru check1. Set the TYPE volume to HM-2/MT-2.
2. Connect an oscillator to INPUT, and input a 344 Hz, 50 mVp-p square wave.
3. Connect an oscilloscope to OUTPUT, and check the output waveform.fig.3
(500mV/div, 1msec)
9. Analog mute check1. Set the TYPE volume to BOOST/LEAD.
2. Connect an oscillator to INPUT, and input a 344 Hz, 50 mVp-p sine wave.
3. Connect an oscilloscope to OUTPUT, and check the output waveform.fig.4
(20mV/div, 1msec)
4. Press MEMORY SELECT. The MEMORY 4 LED will go dark, and the output signal will be muted. Verify that its level is less than -77 dBm (IHF-A).
15
Apr.2002 OD-20(T)
BLOCK DIAGRAMfig.block
INPUT
DC IN
OUTPUT
AMP CTRL
LINEOUT/PHONES
IC2
CODEC
IC3AMP
FET SWQ2
Q8FET SW
BUFFERQ3
AMP,LPFIC11
TR SW
Q4,Q5,Q7
IC6
CPU
RESET
IC7
IC5
DSPCOMPARATORIC10
Q10FILTER
IC8
DC-DC CONVERTER
Q11,
EEPROMIC4
BUFFER
Q1
PRE EMPHASISAF/AD
IC1
BUFFER
Q12
DE EMPHASIS
BATTERY CN4
TR SW TR SWQ6Q9
-9V
CN3CN5
WIRING 10P
WIRING 15P
CN1
CN2
CN1
CN2
VR1,VR2,VR3,VR4
VR5,VR6,VR7
SW1,SW2,SW3
SW4,SW5,SW6
LED1,LED2,LED3,LED4
LED5,LED6,LED7,LED8
LED9,LED10,LED11,LED12
RIBON CABLE
PANEL BOARD
JACK BOARD
3pin +A 9
+D 3. 3
JK1
1
23
JK2
1
23
JK4
1
23
JK3
1
23
JK5213
X211.2896MHz1
2
X18MHz
1 2
1
2
3
1 2
1 2
16 17
Apr.2002
CIRCUIT BOARD(JACK)Circuit_Jack-1.eps
Circuit_Jack-2.eps
18
OD-20(T)
CIRCUIT BOARD(PANEL)Circuit_Panel.eps
19
Apr.2002 OD-20(T)
CIRCUIT DIAGRAM(JACK)fig.jack
GUITAR INPUT
DC IN
TO BATTERY
OUTPUT
AMP CTRL
148/40usPre-Emphasis
DC IN
td=48ms
PHONES/LINE
LED_POWER
LED_AMP_CTRL
CA3
CA3
LED_ON/OFF
LED_4
LED_4LED_3
LED_MEMORY
LED_VARIATION
LED_MANUAL
LED_ON/OFFLED_MANUALLED_MEMORYLED_AMP_CTRLLED_VARIATION
LED_3
CA4
CA4
LED_2
LED_2
P03P04
LED_1
LED_1
VR_TONE
VR_ATTACKVR_OCTAVE
VR_LEVEL
VR_BOTTOM
VR_TYPEVR_DRIVE
CA1CA0
CA1
CA2
CA0
CA2
SW_ON/OFF
SW_VARIATION
SW_ON/OFF
SW_AMP CTL
SW_WRITE
SW_MAN/MEMSW_VARIATION
SW_MAN/MEM
SW_AMP CTL
SW_SELECT
SW_SELECTSW_WRITE
P04P03
+
+D 3. 3
D
+D 3. 3
A
+D 3. 3
D
+
AA
+
+D 3. 3
+
A
+
A
A
+
AA
+
+D 3. 3
+ +
+
+
+
A A A
+
D
+D 3. 3
D
D
+D 3. 3
D
D
D
+D 3. 3
D
D
+D 3. 3
+D 3. 3
D
+D 3. 3
D
+D 3. 3
+D 3. 3
D
D
D
+D 3. 3
D
D
+D 3. 3
D
+D 3. 3
AD
D
+D 3. 3
D
D
-
A
A
D
+
A A A
+
+D 3. 3
D
D
+D 3. 3
D
D
D
+D 3. 3 +
D
DD
-
+
A
A
A
A
A
A
A
A
+
A
+
+
A
+D 3. 3
D
+D 3. 3
+
A
A
A
R110k
C1
0.47S
Q12SK880GR
3
12
L3SLF7045T-151MR37-2(150uH)
IC8S-8520E33MC-BJS-T2
ON/OFF1
VIN5
VSS2
EXT4
VOUT3
D7SS14
C76100/16
CN3
112233
RIBON CABLE 2mm 3P
11 22 33
D5SS14
IC2 AK4552VT
LIN2
SDTO8
RIN1
VD5 MCLK
11BCLK12
PDN13
DEM17
VCOM14
LRCK10
VSS3
SDTI9
DEM06
VA4
ROUT16
LOUT15 +
-
IC3BM5218AFP
6
57
R2512k
R3412k
D41SS355
12
Q82SK879Y 3
12
Q10 2SC4116GR
1
23
C790.1
C510.1 C54
100/16
C52100/16
C530.1
C77 0.1
C330.047
R45100k
R51M
R61k
Q11 IRF7606
S2
D7
S3
D5
G4
S1
D8
D6
R23 15k
C12 270p
R3615k
C22270p
R29
1M
C4
10/16
Q22SK879Y 3
12
D11SS355
12
R271M
R2147k
C170.047
R28100k
R2
1M
R3
1M
R30
39k
R26 47k
C13 270p
R1710k
C90.0022
C191/50
R4470k Q3
2SC3324GR1
23C3
1/50C21/50
C31100/16
C320.1
R4010k
R4610k
C2010/16
C210.1
R3510k
R3310k
+
-
IC1CNJM2100M
84
C35
0.1
R49
10k
R50
10k
C42 0.1
C44 0.1
C46 0.1
C40 0.1
C38 0.1
C6918pX2
CX-49G 11.2896MHz
C67 0.068
C43 0.1
C45 0.1
C47 0.1
C36 0.1
R611k
C34 47/16
R54 33
R601M
IC5TC220C120AF-006(MR3)
OSC1
VS
S2
OSCSEL3
VS
S4
XTO5
XTI6
VD
D7
DIVS08 DIVS19
PLLBP10
VS
S11
VS
S12
TESTP13
VD
D14
VDD15
PLLVAA16
PLLRO17
PLLLP18
PLLAGS19
PLLAGD20
VSS21
VS
S22
VD
D23
VD
D24
RST25
VS
S26
CD727
CD628
CD529
CD430
VS
S31
TESTS32
VD
D33
CD334
CD235
CD136
CD037
VD
D38
DRQ39INT040INT141
DRST42
VS
S43
CA444
CA345
CA246
CA147
CA048
VD
D49
RD50
CS51
VS
S52
WR53
VS
S54
DIV55
VD
D56
DA057
AD058
VD
D59
BCK60
VS
S61
LRCK062
LRCK163
VD
D64
MCK65
VS
S66
DA167
AD168
DA269
AD270
VS
S71
CTYPE72
VD
D73
DA374
AD375
SYI76
TESTB77
TESTT78
VD
D79
VS
S80
C640.1
X149US SMD1 8MHz
C70 22p
C68 22p
R51
100
C58
0.01
C57
0.01
C59
0.01
C60
0.01
C56
0.01
C55
0.01
C61
0.01
IC4
CAT24WC02J
A01
A12
A23
VSS4 SDA
5
SCL6
WP7
VCC8
R1827 (2W)
R3710
C240.1
C2310/16 C25
10/16C260.1
C300.1
C291/50
JK1
HTJ-064-12D
1
23
C5
0.0022 C6 100p
C710/16
R16
47k
R8
47k
+
-
IC1ANJM2100M
2
31
R12
10k
+
-
IC1BNJM2100M
6
57
R20150k(F)
R24
10k(F)
TP1 TH1
TP2 TH1
R5347k
R5247k
JK2
HTJ-064-12D
1
23
RIBON CABLE 2mm 3P
11 22 33
C810/16
C1510/16
C1610/16
Q52SA1298Y
1
32
R1310k
Q42SA1586GR
1
32
R1510k
R1110k
R3210k
C48NFM4516P13C204F
JK6 DJ-0711-020213
JK5 KM02009_B213
R572.2k
Q72SC3265Y
1
23
R48miniSMDC075
C1010/16
C110.1
R1410k
R1910k
L2SLF7032T-4R7M1R7-2 (4.7uH)
IC6 MN101C30A
LED3/D3/P8357
LED2/D2/P8258
LED1/D1/P8159
LED0/D0/P8060
AN0/PA062AN1/PA163AN2/PA264AN3/PA31AN4/PA42AN5/PA53AN6/PA64AN7/PA75
VDD7
OSC28
OSC19
VSS10
P22/IRQ229 P23/IRQ330 P24/IRQ431
P67/A744
P27/RST21MMOD13
LED7/D7/P8753
LED6/D6/P8654
LED5/D5/P8555
LED4/D4/P8456
P66/A643
P65/A542
P64/A441
P63/A340
P62/A239
P61/A138
P60/A037
P70/A845 P71/A946 P72/A1047 P73/A1148 P74/A1249 P75/A1350 P76/A1451 P77/A1552
P21/IRQ1/SENS28
P20/IRQ027
VREF+6
VREF-61
X111
X012
P50/WE32 P51/RE33 P52/CS34 P53/A1635 P54/A1736
P14/TM4IO26
P13/TM3IO25
P11/TM1IO23P12/TM2IO24
P10/TM0TO/RMOUT22
P06/BUZZER/DK20
P05/SBT119
P04/SBI118
P03/SBO117
P02/SBT016
P01/SBI0/RXD15
P00/SBO0/TXD14
C78100/16
C1410/16
C1810/16
RA5 1001 82 73 64 5
D61SS3551
2
C720.01
R62330
D9
N.I.U.
12
D802DZ5.1Y
12
RA6 100
1 82 73 64 5
R5547k
R5647k
CN2
A2001WR2-15P
11 22 33 44 55 66 77 88 99 10
10 1111 1212 1313 1414 1515
RA447k
18
27
36
45
RA2 680
1 82 73 64 5
RA3 680
1 82 73 64 5
Q62SC4116GR
1
23
R4147k
R441M
Q92SC4116GR
1
23
R3147k
R4747k
R5810k
C800.001
R2227 (2W)
JK4
HTJ-064-12I
1
23
CN4
53015-0210
1122
C39 0.1
C41 0.1
C37 0.1
R10100k
+
-
IC3AM5218AFP
2
31
+
-
IC3CM5218AFP
84
C840.1
R73 10k
R75
100k
R78
100k
R74470k
+
-IC10C
M5216FP
84
R7710
C9310/16
C6510/16
C74 47/16
C6310/16
+
-IC10B
M5216FP
6
57
C750.1
+
-IC10A
M5216FP
2
31
C7122p
C660.1
C620.1
R79
10
C94
1/50
D10
1SS355
1 2
C91 1/50
DA3 1SS30221
3
R76
10
C92100/16
+
- IC11A
M5216FP
2
31
R82100k
R83100k
C950.0018
R65330
R94.7k
+
- IC11B
M5216FP
6
57
R86100k
R87100k
C90150p
R69330
R67100k
C87
0.22/50
C49
100/
16
C50
0.1
C83150p
C88150p
C85150p
R710k
JK3
HTJ-064-12D
1
23
C81
100/16
R81 10k
R8010k
R664.7k
R8410k
R85 10kC890.0018
C86
100/16
R64
68(1/2W)
R68
68(1/2W)
R72 680
+
- IC11C
M5216FP
84
D2
1SS352
D3
1SS294
R88 4.7kR59 27k
CN1
A2001WR2-10P
11 22 33 44 55 66 77 88 99 10
10
R7010k
C730.1
IC7
S-80930CLMC
OUT1
Cp5
VDD2
NC4
VSS3
IC12
N.I.U.(S-80130ALMC-JAP-T2)
DS1
GND2
NC3
VDD5
OUT4
Q122SC3324GR1
23
R100
10k
R10110k
R102100k
R103100k
C100 N.I.U.
C101 N.I.U.
C102 N.I.U.
20 21
Apr.2002 OD-20(T)
CIRCUIT DIAGRAM(PANEL)fig.panel-c
(50KB) (50KB) (50KB) (50KB)
EFFECT ON/OFF MANUAL
(50KB) (50KB)
MEMORY VARIATION 1234
DRIVEBOTTOMTONELEVELATTACK
OCTAVETYPE
AMPCTRL
EFFECT ON/OFF
MAN/MEM VARIATION AMP CTRL WRITE SELECT
(50KB 11click )
SHAPEHEAVY
(CENTER CLICK)
+D 3. 3
D
+D 3. 3
D
+D 3. 3 +D 3. 3 +D 3. 3 +D 3. 3 +D 3. 3 +D 3. 3+D 3. 3 +D 3. 3
D
+D 3. 3
D D D D D D D
+D 3. 3
VR2
RD901-40-125F-B54-0CD
1
2
3
VR4
RD901-40-125F-B54-00D
1
2
3
VR1
RD901-40-125F-B54-00D
1
2
3
VR3
RD901-40-125F-B54-00D
1
2
3
VR6
RD901-40-125F-B54-00D
1
2
3
VR5
RD901-40-125F-B54-00D
1
2
3
VR7
RD901-40-125F-B54-11D
1
2
3
LED12L-113GDT
12
LED5
L-34HDSL
12
LED6
L-312LRD
12
LED8
L-34HDSL
12
LED9
L-34HDSL
12
LED10
L-34HDSL
12
LED11
L-34HDSL
12
LED3
L-34HDSL
12
LED4
L-34HDSL
12
LED7
L-312LRD
12
C1 N.I.U.
SW1
SKQKAH12
SW2
SKQKAH12
SW3
SKQKAB12
SW4
SKQKAB12
SW5
SKQKAB12
SW6
SKQKAB12
CN2
WIRRING 15P
11223344556 6778899101011111212131314141515
CN1
WIRRING 10P
1122334455667 788991010
22 23
Apr.2002
24