Boss DR-770 Service Notes
-
Upload
fernando-gomez -
Category
Documents
-
view
225 -
download
0
Transcript of Boss DR-770 Service Notes
8/3/2019 Boss DR-770 Service Notes
http://slidepdf.com/reader/full/boss-dr-770-service-notes 1/18
DR-770 Feb. 1999
1
TABLE OF CONTENTS PageSPECIFICATIONS ............................................................................................... 1
Deterioration in the conductive coating inside the case ............................................................................................... 2
PANEL LAYOUT . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 2
EXPLODED VIEW ............................................................................................... 3
PARTS LIST . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 4
LOADING THE FACTORY PRESET DATA ............................................................................................... 6
IDENTIFYING THE VERSION NUMBER ............................................................................................... 6
USER DATA SAVE AND LOAD ............................................................................................... 6
How to save the User Data ............................................................................................... 6
How to load the User Data ............................................................................................... 7
TEST MODE . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 8
TROUBLESHOOTING ............................................................................................... 11
ERROR MESSAGE ............................................................................................... 12
BLOCK DIAGRAM ............................................................................................... 13
CIRCUIT DIAGRAM (JACK) ............................................................................................... 14
CIRCUIT BOARD (JACK) ............................................................................................... 15
CIRCUIT DIAGRAM (MAIN) ............................................................................................... 16
CIRCUIT BOARD (MAIN) ............................................................................................... 17Change Information ............................................................................................... 18
SERVICE NOTES
First Edition
Issued by RJA
Copyright © 1999 by ROLAND CORPORATIONAll rights reserved. No part of this publication may be reprodu ced in any form without the written permission of ROLAND CORPORATION.
17059959 Printed in Japan AA00 (DP)
Dr. Rhythm
SPECIFICATIONSq Instruments
255
q Maximum Polyphony
14 voices
q Rhythm PatternsPreset Patterns : 400
User Patterns : 400
q SongSongs :100
Song Length : Maximum 250 parts for a song
Total Parts for Songs : 10,000
q Effect
Reverb,Flanger
q Resolution
Per quarter note : 96
q TempoQuarter note=20 ~ 260
q Data Input MethodRealtime/Step
q Maximum Note Storage
approx.11,200note
q Output LevelMax.7 Vp-p(L(MONO),R)
q Noise Level
Less Than -78 dBm(DIN AUDIO)((L(MONO))
q Output Impedance1k Ω(L(MONO),R, INDIVIDUAL))
q Power Source
AC Adaptor BOSS BRC Series
q Current Draw700mA
q Dimensions
215(W)×165(D)×57(H)mm
8-1/2(W)×6-1/2(D)×2-3/8(H)inches
q Weight
715g/1 lbs 10 oz
q AccessoriesOwner's Manual Set(English) : PNo.71238223
Owner's Manual Set(Japanese) : PNo.71238145AC Adaptor
AC ADAPTOR BRC-100 BOSS :PNo.00899078
AC ADAPTOR BRC-120 BOSS :PNo.00899089
AC ADAPTOR BRC-230 BOSS :PNo. 00899090
AC ADAPTOR BRC-240A BOSS :PNo. 00899101
EURO CONVERTER PLUG ECP01-5A :PNo. 00905234
本書の一部、もくしは全部を無断で複写・転載することを禁じます。
音色数255
最大同時発音数14 voices
リ ズムパターン数プリセットパターン :400ユーザーパターン :400
ソ ン グソング数 : 100ソング長 :1ソング当たり最大250パターン総ソング長 :10,000
エ フェクト
リバーブ、フランジャー
分解能4分音符当り:96
テンポQ uarter note/4分音符=20 ∼ 260
データ入力方式リアルタイム、ステップ
最大記憶音数約11,200音
出力レベル最大7 Vp-p(L(M ON O),R)
ノイズレベル-78 dBm以下(DIN A UD IO)((L(M ON O))
出力インピーダンス1kΩ(L(M ON O),R, IND IVIDU AL ))
電源
AC アダプター BOSS BR C シリーズ
消費電流700mA
外形寸法215(W )×165(D )×57(H )mm8-1/2(W )×6-1/2(D)×2-3/8(H)inches
重量715g/1 lbs 10 oz
標準付属品取扱説明書(和文) :PNo.71238145取扱説明書(英文) :PNo.71238223保証書(Japan Only) :PNo.40232334AC AdaptorAC A DA PTOR B RC-100 BOSS :PNo.00899078
主な仕様
目次
主な仕様
ケース内側の導電塗装の劣化について
パネル配置図
分解図
パーツリスト
ファクトリー・プリセット・データのロードの方法
バージョンの確認方法
データのセーブとロードの方法
ユーザーデータのセーブ方法
ユーザーデータのロード方法
テストモード
トラブルシューティング
エラー・メッセージ
ブロック図
回路図 (JAC K)
基板図 (JAC K)
回路図 (M AIN )
基板図 (M AIN )変更案内
8/3/2019 Boss DR-770 Service Notes
http://slidepdf.com/reader/full/boss-dr-770-service-notes 2/18
DR-770 Feb. 1999
2
PANEL LAYOUT
FRONT VIEW
REAR VIEW
Top Case(01787767)
LED (red)SLC-22VR3F15039221
LED (green)SLC-22MG3F15039222
Rubber Switch KEY(01787790)
Rubber Switch PAD(01787801)Pressure Sheet Sensor(25095101)Plate(22055165)
<Top View>
Display Cover(01787778)LCDRCD1627R(01788490)
DR-Knob (BLK)(22485303)Rotary VolumeRK14k 124 50KB×2(13289189)
DR-Knob (BLK)(22485303)Rotary EncoderEC16B 24204(01231367)
KEY Top(12499175)SwitchSPUN19F(13129369)
JackHEC0740-01-010(13449728)
JackYKB21-5130(13449433)
JackHLJ7101-01-3010(13449283)
Bottom Case(01787734)
JackHLJ7001-01-3010(13449284)
MIDI ConnectorM-S2-3P(13429642)
sDeterioration in the conductive
coating inside the case
The inside of the case is coated with a conductive material. If the
board undergoes repeated detaching/attaching, the coating on the
boss may deteriorate.
If the resistance value between the case center and the head of the
boss becomes 5Ω or more, the effect of conductive coating cannot
be expected. In such a case, replace the case.
/ 背面図
/ 正面図
/パネル配置図sケース内側の導電塗装の劣化に
ついて
ケース内側には導電塗装が施されていますが、基板の取り外
し、取り付けを繰り返すと、ボスの部分の塗装が劣化してき
ます。
ケース中心とボスの頭との抵抗値が、5Ω以上になると、導電
塗装の効果が望めなくなりますので、ケースを交換して下さ
い。
8/3/2019 Boss DR-770 Service Notes
http://slidepdf.com/reader/full/boss-dr-770-service-notes 3/18
DR-770 Feb. 1999
3
A
B
C
D
EF
G
H
I
J
KL
M
N
O
P
Q
R
S
T
U
V
EXPLODED VIEW
[Part]NO. PART CODE PART NAME DESCRIPTIONq 01787734 BOTTOM CASE
w 01898189 FOOT D10 T4
e 71238156 JACK BOARD ASSY
r 12449445 FERRITE-CORE ESD-R-16C
t 71238167 VR BOARD ASSY
y 71238178 ENC BOARD ASSY
u 01892034 VR SHIELD SHEET
i 71238123 MAIN BOARD ASSY (EXG)
o 22055165 PLATE 205-165
!0 250 95101 PRESSURE SHEET SENSOR 509 -101
!1 23365653 RUBBER CONNECTOR 336-653
!2 01788490 LCD RCD1627R
!3 01787790 RUBBER SW KEY
!4 01787801 RUBBER SW PAD
!5 01787767 TOP CASE
!6 12499175 G S-BUTTON S1H BLK 249-175
!7 01787778 DISPLAY COVER
!8 22485303 D R-KNOB L BLK 248-303
[Screw]NO. PART CODE PART NAME DESCRIPTIONa 40012456 SCREW M2.6×8 BINDING TAPTITE P FE NI
b 40012489 SCREW M2.6×10 BINDING TAPTITE FE BZC
c 40011223 SCREW M2.6×6 BINDING TAPTITE P NI
d
This MG WASHER and MG NUT are included in the #01231367 ROTARY ENCODER.
This MG WASHER and MG NUT are included in the #13289189 POTENTIOMETER.
!1
!8
!6
!4
!2
!3
!5
!7
a
b
c
1
2
3
4
7
8
9
!0
d
e
6
5c
/分解図
d このワッシャーとナットは、#01231367 ROTA RY EN CO DE R に含まれます。
e このワッシャーとナットは、#13289189 PO TEN TIOM ETER に含まれます。
8/3/2019 Boss DR-770 Service Notes
http://slidepdf.com/reader/full/boss-dr-770-service-notes 4/18
DR-770 Feb. 1999
4
*1 *2
↓ ↓ CASING Q'ty
# 01787734 BOTTOM CASE 1
# 01787767 TOP CASE 1
# 01787778 DISPLAY COVER 1
22055165 PLATE 205-165 1
KNOB, BUTTON
12499175 G S-BUTTON S1H BLK 249-175 1
22485303 D R-KNOB L BLK 248-303 2
# 01787790 RUBBER SW KEY 1
# 01787801 RUBBER SW PAD 1
SWITCH
13129369 SPUN19430A PUSH SWITCH SW101 on JB 1
JACK, SOCKET
13429642 M-S2-3P MIDI SOCKET JK108,JK107 on JB 2
13449433 3.5MM STEREO YKB21-5130 JACK JK105 on JB 1
13449283 6.5MM HLJ7101-01-3010 JACK JK102,JK103,JK104 on JB 3
13449284 6.5MM HLJ7001-01-3010 JACK JK101 on JB 1
13449728 HEC0740-010010 ADAPTOR JACK JK106 on JB 1
DISPLAY UNIT
# 01788490 RCD1627R LCD 1
PCB ASSY
# E 71238123 MAIN BOARD ASSY (EXG) 1
NOTE : 'MAIN BOARD ASSY' includes the following parts.
12169388 LED SPACER LH-3-3 2
# 71238178 ENC BOARD ASSY 1
NOTE : 'ENC BOARD ASSY' includes the f ollowing parts.
23505274 WIRING HARNESS B 3P 350-274 1
# 71238156 JACK BOARD ASSY 1
NOTE : 'JACK BOARD ASSY' includes the following parts.
# 01898889 WIRING GND 1P 1# 01788556 WIRING 6P 1
# 01898989 WIRING W11 1
# 01898001 HEATSINK (DR-770) 1
22465939 HEATSINK (DR-660) 1
22190758 HOLDER DIN SOCKET (2P) 1
40011112 SCREW M3¥10 BINDING TAPTITE B BZC 2
40011090 SCREW M3¥6 BINDING TAPTITE B BZC 2
40016512 LOCKING TIE 80M/M T-18S 2
40016545 INSULOK TIE SKM-1 1
# 71238167 VR BOARD ASSY 1
NOTE : 'VR BOARD ASSY' includes the following parts.
23505275 WIRING HARNESS C 6P 350-275 1
IC
# 01784678 HD6415108RF12 IC (CPU) IC6 on MB 1
15199923 SED1278F0A IC (LCD DRIVER) IC9 on MB 1
15239197 MB622928PF-G-BND-ER IC (GATE ARRAY) IC19 on MB 115239229 TC6116AF (GP-4) IC (PCM CUSTOM) IC5 on MB 1
01560289 TC55257DFL-55L(EL) IC SRAM IC10 on MB 1
01122412 TC551001CF-70L IC (SRAM) IC12 on MB 1
# 01788589 LHMN4708 IC (MASK ROM) IC8 on MB 1
# 01788578 LHMN5KRP WAVE ROM IC (MASK ROM) IC4 on MB 1
01340789 BU9480F IC (D/A CONVERTER) IC15,IC16 on MB 2
15259864T0 TC74HC4052AF(EL) IC IC13,IC11 on MB 2
15249104 TC7S04F(TE85L) IC (C MOS) IC14 on MB 1
15249111 TC7WU04F(TE12L) IC (C MOS) IC3 on MB 1
15259889 TC7S02F(TE85L) IC IC18 on MB 1
15269805 TC74AC14F(EL) IC IC2 on MB 1
15269810 TC74AC138F(EL) IC (CMOS) IC17 on MB 1
15289131 BA10393F-E2 IC (COMPARATOR) IC1 on MB 1
15289709 M51954BFP-600D IC (RESET) IC20 on MB 1
15289125 PC-410KT 178FAY IC (PHOTO COUPLER) IC7 on MB 1
15189186 UPC4570C IC (OP AMP) BIPOLAR IC102,IC101 on JB 2
15189248 M5216P IC (OP AMP) BIPOLAR IC103 on JB 1
# 01784834 M62421SP FILTER IC106 on JB 1
# 01897801 UPC7805AHF IC (REGULATOR) IC104 on JB 1
# 01897223 UPC24M09AHF IC (REGULATOR) IC105 on JB 1
TRANSISTOR
15309101 2SA1037KR T146 QRS TRANSISTOR Q3 on MB 1
15329518 DTA114TKT146 TRANSISTOR Q2,Q1 on MB 2
# 00894489 2SA1049-GR(TPE4) TRANSISTOR Q104 on JB 1
# 01788734 2SC2459-GR(TPE4) TRANSISTOR Q106,Q105 on JB 2
15129204 DTC343TS TP TRANSISTOR Q101,Q102,Q103 on JB 3
PARTS LIST
CONSIDERATIONS ON PARTS ORDERING
When ordering any parts listed in the parts list, please specify the following items in the order sheet.
Q TY PAR T NU MBER D ESCR IP TI ON MO DEL N UMBER
10 22575241 Sharp key C-20/50
15 2247017300 Knob (orange) DAC-15D
Failure to completely fill the above items with correct number and description will result in delayed or even
undelivered replacement.
Ex.
SAFETY PRECAUTION:*1
The parts marked have safety-
related characteristics.
U s e on l y l i s t e d pa r t s f o r
replacement.
MB → Main Board Assy
VB → VR Board Assy
EB → ENC Board Assy
JB → Jack Board Assy
The parts marked #
are new (initial
parts). *2
Note : Consider about the natural environment carefully before through the old lithium battery away when you exchange to the new one.you exchange to the new one.
/ケース
/つ まみ、 ボ タン
/ ス イ ッ チ
/ ジャ ッ ク 、 ソ ケ ッ ト
/表示ユニット
/基板完成品
注意 : 補修用 M A IN B O AR D A SSY は、下記の部品を含みます。
注意 : 補修用 ENC B O AR D A SSY は、下記の部品を含みます。
注意 : 補修用 JA CK BO A RD ASSY は、下記の部品を含みます。
注意 : 補修用 V R B OA RD ASSY は、下記の部品を含みます。
/トラ ン ジ スター
パーツ発注に関するお願い
オーダーシートには、必ず下記の4項目は正確に記入して下さい。(例外は除く)必要数 パ ーツナンバー 品名 使用機種
10 22575241 Sharp key C-20/50
15 2247017300 Knob (orange) DAC-15D
もし記入洩れ、誤記等が有る場合、必要部品が発送できなかったり、大幅な遅れの原因になります。御協力をお願いします。
例)
安全上の注意:*1
が付いている部品は、安全上特別な規格でつくられたものです。交換の際は、指定された部品番号以外の部品は使わないようにして下さい。
/パーツリ スト
#の付いた部品は新
規部品です。*2
注意 :リチウム電池の交換時に、不要になったリチウム電池は、環境問 題を十分考慮した上で処理して下さい。
8/3/2019 Boss DR-770 Service Notes
http://slidepdf.com/reader/full/boss-dr-770-service-notes 5/18
DR-770 Feb. 1999
5
DIODE
15339135T0 1SS300(TE85R) DIODE DA2-DA20 on MB 19
01127489 RB715F T106 SCHOTTKY DIODE DA1 on MB 1
# 15039221 SLC-22VR3F LED LED1 on MB 1
# 15039222 SLC-22MG3F LED LED2 on MB 1
15019126 1SS133 T-77 SWITCHING DIODE D104,D105,D106,D107 on JB 4
15019260 1G4B42 1A/400V BRIDGE DIODE D102 on JB 1
01122323 MTZJ T-77 8.2B ZENER DIODE D101 on JB 1
01122312 MTZJ T-77 5.6C ZENER DIODE D103 on JB 1
RESISTOR
15399975 RCE9A223JA (22KOHM X8) RESISTOR ARRAY RA4 on MB
15409113 EXBV8V103JV RESISTOR ARRAY RA7 on MB 1
1 53 99 96 5 RCE9 A1 03 JA G7 A (1 0K OH M X 8) RE SI STO R A RRA Y RA 1,R A2 ,RA 3 o n M B
# 01788489 CNB2B9ZTE332 J R-ARRAY RA5,RA6 on MB 2
# 13749187 SR50TR 220 J CARBON RESISTOR R127,R132 on JB 2
# 01897834 ERF5AJ 150 CEMENT RESISTOR R137 on JB 1
# 01897812 RSSX3 5.6 OHM J MTL.OXIDE RESISTOR R136 on JB
POTENTIOMETER
13289189 RK14K124 L1=15 50KBX2 POTENTIOMETER VR301 on VB 1
CAPACITOR
# 00783990 MMTVA0050J474 200 M.POLYEST CAP. C150,C151 on JB 2
# 01897778 16MV470CZ CHEMICAL CAPACITOR C154 on JB 1
# 01897789 25MV470CZ+T CHEMICAL CAPACITOR C136,C137 on JB 2
# 01897790 16MV100UGX+T CHEMICAL CAPACITOR C142 on JB 1
# 01897945 35MV10UGX CHEMICAL CAPACITOR C163 on JB 1
INDUCTOR, COIL, FILTER
12449370 SBT-0160W EMI FILTER L117 on JB 1
12449381 SBT-0460TF (TP) EMI FILTER L101-L111 on JB 11
12449445 ESD-R-16C FERRITE-CORE 1
CRYSTAL, RESONATOR
00891801 MA-406 24.000MHZ CRYSTAL X1 on MB 1
ENCODER
01231367 EC16B24204 (L=15) ROTARY ENCODER on EB 1
CONNECTOR
23365653 336-653 RUBBER CONNECTOR 2
13369874 IL-Z-11PL-SMTY-E1500 CONNECTOR CN2 on MB 1
13369928 53253-0610 CONNECTOR CN1 on MB 1
13369968 IL-404-17S-LW CONNECTOR CN3 on MB 1
13369942 53254-0610 CONNECTOR CN101 on JB 1
13369939 53254-0310 CONNECTOR CN103 on JB 1
SCREW
4 00 12 48 9 SC REW M2 .6×10 BINDING TAPTITE FE BZC 1
4 00 11 22 3 S CREW M2 .6×6 BINDING TAPTITE P NI 9
4 00 12 45 6 S CREW M2 .6×8 BINDING TAPTITE P FE NI 6
PACKING
# 01897923 PAD ADAPTOR 1
# 01788512 PAD UPPER 1
# 01788523 PAD LOWER 1
# 01788501 PACKING CASE 1
MISCELLANEOUS
12569249S0 LITHIUM BATTERY CR2032 220MAH/3V 1
# 01898189 F OOT D10 T4 4
25095101 PRESSURE SHEET SENSOR 509-101 1
# 01892034 VR SHIELD SHEET 1
13429566 IC SOCKET 400-032-001 32P 1
12569420 LITHIUM BATTERY HOLDER (HL32-A2) FOR CR2032 1
ACCESSORIES (STANDARD)
00899078 AC ADAPTOR BRC-100 1
00899089 AC ADAPTOR BRC-120 1
00899090 AC ADAPTOR BRC-230 1
00899101 AC ADAPTOR BRC-240A 1
00905234 EURO CONVERTER PLUG ECP01-5A (PLUG FOR BRC-230T) 1
# 71238145 OWNER'S MANUAL JAPANESE 1
# 71238223 OWNER'S MANUAL ENGLISH 1
/ダイオード
/抵抗
/ボリューム
/コンデンサー
/ イ ン ダク タ ー 、 コ イ ル 、 フ ィ ル タ ー
/クリス タル、 発振子
/エンコーダー
/コ ネ クター
/ねじ類
/梱包材
/その他
/標準付属品
40232334 保証書 (JAPAN ONLY)
8/3/2019 Boss DR-770 Service Notes
http://slidepdf.com/reader/full/boss-dr-770-service-notes 6/18
DR-770 Feb. 1999
6
LOADING THE FACTORY
PRESET DATA
1. Turn off the power to the DR-770.
2. While simultaneously pressing the [RESET] and [REC] buttons
turn the power on.
3. The display will show “INIT?”.
4. Press the [ENTER] button and the display will show “SURE?”.
NOTE : If initialization is not necessary do not press the [ENTER]
button.
Press the [STOP/EXIT] button. The display will show “Aborted”
and the operation will enter normal mode.
5. Press the [ENTER] button again. The DR-770 is loaded the
Factory preset Data and then the display will show “Done” and
the operation will enter normal mode.
IDENTIFYING THE VERSION
NUMBER
1. While simultaneously pressing the [SONG] and Numericbutton [7] turn the power on.
The version number will appear on the LCD display as shown
below . The displayed version of number is ROM (IC8 on Main
Board) 's version number.
2. When pressing the Numeric button [8], the display will show
“INIT ?”.
Then press the [ENTER] button the display will show
“SURE?”. If you want to initialize the DR-770 press the
[ENTER] botton again.
The display will show “Done” and the operation enters normal
mode.
If not initializing, press the [STOP/EXIT] button. The display
will show “Aborted” and the operation enters normal mode.
The displayed date differs depending on the ROM version.
USER DATA SAVE AND LOAD
To save the data stored in the RAM of the mainframe (DR-770) in
an external memory or load external MIDI.
Methods of transmitting and receiving data are explained below.
NOTE : If loading is executed all data stored in the RAM of the
mainframe will be lost.
NOTE : If you select “ALL” and execute the Bulk Dump, the
memory on the receive device will be full before the Bulk Dump iscompleted, not being able to receive any more data.
If this happens, change the data to be transferd to “SEQ,”
“GLOBAL,” “DRMKITS,” or “1DRMKIT,” then execute the Bulk
Dump again.
How to save the User Data
Connections
Procedure
1. Press [MIDI] to make“MIDI” light.
The DR-770 is now in MIDI mode.
2. Use [ ] [ ] to select “9 BULK.”
PADBANKFUNCMODE
MIDI OUT
Receive device
MIDI IN
Transmit device (DR-770)
MIDI sequencerComputeretc.
FUNCMODE
INSERTCOPY
DELETE
SONGPATTERN
PADUTILITY
REALSTEP
EFFECTSMIDI
QUANTIZENEXTPTNPART
BEATLENGTHPATTERN
Data to be transferred
フ ァ ク ト リ ー・プ リ セ ッ ト ・データ
のロード の方法
1. D R -770の電源を一旦切ります。
2. [RES ET ] ボタンと [REC ] ボタンを同時に押しながら電源
を入れます。
3. L C Dディプレイに、“IN IT ?”と表示されます。
4. [EN TE R] ボタンを押すと、LC Dディスプレイに、“Sure
?”と表示されます。
注 意:イニシャライズをしない場合は、[EN TE R ] ボタンを
押さずに、[ST O P/EX IT] ボタンを押して下さい。すると、
LC Dディスプレイに、“A borted”と表示され、通常モードに
なります。
5. もう一度 [EN TE R ] ボタンを押すと、ファクトリー・プリ
セット・データがロードされてLC D ディスプレイに、
“D one”と表示され、通常モードに入ります。
バージョ ンの確認方法
1. [SO N G ] ボタンと数字ボタン [7] を同時に押しながら電源を入れます。
LC Dディスプレイに、下記のように表示されます。
表示されるR O M のバージョンは、RO M (IC8 on M ain
B oard)のものです。
2. 数字ボタン [8] を押すと、“INIT ?”表示されます。
[EN TE R ] ボタンを押すと、LC Dディスプレイに、“SU RE
?”と表示されます。
D R-770をイニシャライズする場合は、再度、[EN TE R ] ボ
タンを押して下さい。
LC Dディスプレイに、“Don e”と表示され、通常モード
になります。イニシャライズしない場合は、[ST O P/EX IT]ボタンを押して下さい。すると、LC Dディスプレイに、
“A borted”と表示され、通常モードに入ります。
(日付けはRO M のバージョンによって違います)
データのセーブとロ ード の方法
本体のRA M に記憶したデータを、外部にセーブしたり、ある
いは、外部のデータを本体のRA M にロードするには、M ID I
のエクスクルーシブ・メッセージを使用します。
以下に、データの送信、受信方法を説明します。
注 意:データのロードを実行すると、それまでに、本体内
に記憶されていたデータは、全て消去されます。
注 意:“AL L”を選んでバルク・ダンプを実行した場合、
受信側の機器のメモリーが途中でいっぱいになり、それ以降のデータを受け付けなくなることがあります。
このようなときは、転送するデータをSEQ 、GL O BA L、
D RM K ITS、1D RM K ITのいずれかに分割してバルク・ダンプ
を実行してください。
ユーザーデータのセーブ方法
接続
操作
1. [M ID I] を押して“M ID I”を点灯させます。
M ID Iモードにします。
2. [ ] [ ] を押して、“9 BU LK ”を選びます。
受信側送信側(DR -770)
M ID Iシーケンサーコンピューター
など
転送するデータ
8/3/2019 Boss DR-770 Service Notes
http://slidepdf.com/reader/full/boss-dr-770-service-notes 7/18
DR-770 Feb. 1999
7
3. Use [DEC] [INC] or [VALUE] to select the type of data that
will be transmitted.
AL L: Al l d ata of th e DR -7 70
S EQ: Al l p att er ns an d s on gs
GLOBAL: DPP/roll/metronome/MIDI settings
DRMKITS: All user drum kits
1DRMKIT: A specified individual drum kit (If this data is
transmitted to the DR-770, the drum kit that is
currently selected on the receiving device will
change to the drum kit settings that were
received.)
4. Press [ENTER].
The display will ask “Sure?,” allowing you to confirm whether
you really want to execute the bulk dump.
s If you selected “1DRMKIT,” use [DEC] [INC] or [VALUE] to
select the drum kit whose data you want to transmit.
5. To execute the bulk dump, press [ENTER].
The display will indicate “Trnsmit” (transmitting) ' “Done,”
and the bulk dump will be completed.
If you decide to cancel, press [STOP/EXIT].
The bulk dump will be canceled, and the display will indicate
“Aborted."
QUANTIZENEXTPTNPART
BEATLENGTHPATTERN
PADBANKFUNCMODE
MIDI OUT
Receive device (DR-770)
MIDI IN
Transmit device
MIDI sequencerComputer
etc.
How to load the User Data
Connections
Connections
1. Press [MIDI] to make“MIDI” light.
The DR-770 is now in MIDI mode.
2. Use [ ] [ ] to select “2 MIDIch.”
3. Use [VALUE*] to select the MIDI channel.
s If you want to restore data that was formetly transmitted to a
sequencer, set the unit to the same MIDI channel that was used
when transmitting the data.
s If you want to receive data that being transmittied from another
DR-770, set both DR-770 units to the same MIDI channel.
4. Use [ ] [ ] to select “7 RxEXC.”
5. Use [DEC] [INC] or [VALUE] to turn the setting “ON.”
With playback stopped on the DR-770, receive the data.
FUNCMODE
INSERTCOPYDELETE
SONGPATTERNPADUTILITY
REALSTEP
EFFECTSMIDI
QUANTIZENEXTPTNPART
BEATLENGTHPATTERN
3. [D EC ] [IN C ] または [V A LU E] で、転送するデータを選び
ます。
AL L: DR -770のすべてのデータ
SEQ: パターンとソング全部
G LO BA L: D PP/ロール/メトロノーム/M ID Iの設定
D RM K ITS:ユーザー・ドラム・キット全部
1D RM K IT: ドラム・キットいずれか1つ(DR -770に転送
したときは、受信側で今選ばれているドラ
ム・キットが転送したドラム・キットの設定
になります。)
4. [EN TE R] を押します。“Sure?”とバルク・ダンプを実行しても良いかどうかを
確認するメッセージが表示されます。
“1D RM K IT”を選んだときは、 [D EC ] [IN C] または
[V A LU E] でデータを転送するドラム・キットを選びま
す。
バルク・ダンプを実行するときは、 [EN TE R ] を押しま
す。
5. “Trnsmit”(転送中)→“Done”と表示されてバルク・
ダンプが完了します。
中止するときは [ST O P/EX IT] を押します。
“A borted”と表示されてバルク・ダンプを中止します。
受信側(DR -770)送信側
M IDIシーケンサーコンピューター
など
ユーザーデータのロード 方法
接続
操作
1. [M ID I] を押して“M IDI”を点灯させます。
M IDIモードにします。
2. [ ] [ ] を押して、“2 M ID Ich”を選びます。
3. [V A LU E*] で、M ID Iチャンネルを設定します。
シーケンサーに転送したデータを戻すときは、データを
転送したときと同じM IDIチャンネルに設定します。
別のD R-770から送信されるデータを受信するときは、2台
のD R-770を同じM ID Iチャンネルに設定します。
4. [ ] [ ] を押して、“7 RxE X C”を選びます。
5. [D EC ] [IN C] または [V A LU E] で、“O N”にします。
D R-770の演奏がストップしている状態で、データを受信
します。
8/3/2019 Boss DR-770 Service Notes
http://slidepdf.com/reader/full/boss-dr-770-service-notes 8/18
DR-770 Feb. 1999
8
TEST MODE
CAUTION : When running a test item (RAM check) in the test
mode the backup data in the mainframe will be erased.
Be sure to seve the data before running this test.
To save the data refer to “DATA SAVE AND LOAD”.
Required Items
· Monitor speakers or Headphones,
· MIDI cable
· FS5U× 2 (Polarity switch setting is Jack side)
· Oscilloscope
To enter test mode
While simultaneously pressing the [SONG] and [7] buttons, turn
the power on. The version number will appear on the LCD
display as shown below. The displayed date differs depending on
the ROM version.
This LCD display is referred to as the main screen in the
following procedures.
To exit test mode
On the main screen, press the [8] button.
The display will show “INIT?”.
When initializing:
Press the [ENTER] button. The display will show “Sure?”.
Press the [ENTER] button again. The display will show “Done”
and the operation will exit test mode.
When not initializing:
Press the [STOP/EXIT] button. The display will show “Aborted”
and the operation will exit test mode without initializing the
setting.
Test ItemsThe test mode includes the 8 tests.
0. LED check
1. Switch check
2. LCD check
3. RAM check
4. ROM check
5. MIDI check
6. FSR (Key Pads) check
7. OUTPUT check
NOTE : Each test number corresponds to the [0] to [7] keys on
numeric buttons. To begin a test, press a numeric button that
corresponds to the test number to be run.
[0]. LED check
This test checks whether the LED lights normally.
1. Press the numeric button [0] to run this test.
2. If normal, pressing the [REC] button turns on the red LED,
while pressing the [START] button turns on the green LED.
3. When pressing the [STOP/EXIT] button, the display will
show “OK”.
4. Again, press the [STOP/EXIT] button to return to the main
screen.
[1]. Switch check
This test checks whether each key (except key-pads) and the
encoder (VALUE knob) are functioning.
1. Press the numeric button [1] to run this test.
The display will show as follows:
2. When pressing a button or Foot SW to be checked, the key
name will be displayed in the “ ” field. At
the same time a rim-shot sound will be output from Outputs L
and R.
3. After all the buttons and Foot SW have been pressed for
checking, the test automatically enters the encoder checking.
The display will show as follows:
4. When turning the encoder clockwise (or counterclockwise),
the display shown at right in the figure above will appear.
Then when turning the encoder in the reverse direction, the
display will show “OK” if the encoder is functioning.
5. Press the [STOP/EXIT] button to return to the main screen.
[2]. LCD check
1. Press the numeric button [2] to run this test.
2. When this test is entered, all segments of the LCD will be
displayed.
3. When pressing the [STOP/EXIT] button, the display will
show “OK” (even if the LCD does not operate normally).
4. Again, press the [STOP/EXIT] button to return to the main
screen.
Turning the encoder
(or<<<<<<<)
テスト モード
注意:テスト・モード内のテスト項目“RA M チェック”を
実行すると、本体内にバックアップしているユーザー・
データが消去されてしまいますので、必ず、データのセー
ブを行って下さい。データのセーブ方法は、“データの
ロード/セーブの方法”を参照して下さい。
用意するもの・モニター・スピーカーかヘッドホン、・M ID Iケーブル
・フットスイッチ FS5U ×2、(尚、ポラリティSW を
ジャック側に設定してください)・オシロスコープ
テストモード への入り 方[SON G ] ボタンと数字ボタン [7] を同時に押しながら電源を
入れます。
LC Dディスプレイに下記のように表示されます。
日付はRO M のバージョンによって違います。
以下の文章において、この画面を、メイン画面と呼びま
す。
テストモード の抜け方メイン画面の状態で、数字ボタン [8] を押します。
すると、LC Dディスプレイに、“IN IT?”と表示されます。
・イニシャライズして終了する場合:
[EN TE R ] ボタンを押すと、LCD ディスプレイに、“Sure?”
と表示されます。
もう一度 [EN TE R] ボタンを押すと、“Done”と表示され、
テスト・モードから抜けます。
・イニシャライズせず終了する場合:
[STO P/EX IT] ボタンを押すと、LC D ディスプレイに、
“A borted”と表示され、テスト・モードから抜けられま
す。
テスト項目テストは全部で8項目あります。
0. L EDチェック
1. スイッチ・チェック
2. LC Dチェック
3. RAM チェック
4. ROM チェック
5. M IDIチェック
6. FSR(キー・パッド)チェック
7. OU TPUTチェック
注意:各テスト項目は、数字ボタンの [0] から [7] に対応
しています。
実行したいテスト項目に対応している数字ボタンを押し
て、テストを実行して下さい。
[0]. LEDチェ ッ ク
LE Dのチェックを行います。
1. 数字ボタン [0] を押し、テストを実行させます。
2. [RE C] ボタンを押すと赤のLED が、[STA RT ] ボタンを
押すと緑のLED が点灯します。
3. [STO P/EX IT] ボタンを押すと、LC Dディスプレイに、
“OK ”と表示されます。
4. もう一度[STO P/EX IT] ボタンを押すと、メイン画面に戻ります。
[1]. スイッ チ・ チェック
各ボタン(キー・パッド以外)とエンコーダー( [V A LU E]
ツマミ)のチェックを行います。
1. 数字ボタン [1] を押し、テストを実行させます。
LC Dディスプレイに、下記のように表示されます。
2. 任意のボタン(キー・パッド以外)を押すと、“
”の部分に押したボタンの名前が表示され、同
時に、リムショットの音が、OU TPU T L /R ジャックか
ら出力されます。3. 全てのボタン(キー・パッド以外とフットスイッチ)を
押すと、自動的にエンコーダーのチェックに入ります。
LC Dディスプレイに、下記のように表示されます。
4. エンコーダーを右または左に回すと、上図、右のように
表示されます。
次に反対側に回すと、LC Dディスプレイに、“OK ”と
表示されます。
5. [STO P/EX IT] ボタンを押すと、メイン画面に戻りま
す。
[2]. LCDチェ ッ ク
1. 数字ボタン [2] を押して、テストを実行させます。
2. L CD を全て表示させます。
3. [STO P/EX IT] ボタンを押すと、LC Dディスプレイに、
“OK”と表示されます。(LC Dの表示がおかしい場合
でも)
4. もう一度、[STO P/EX IT] ボタンを押すと、メイン画面
に戻ります。
回す
8/3/2019 Boss DR-770 Service Notes
http://slidepdf.com/reader/full/boss-dr-770-service-notes 9/18
DR-770 Feb. 1999
9
[3]. RAM check
1. Press the numeric button [3] to run this test.
This test automatically performs the RAM check.
If normal, the display will show “OK”. If a malfunction is
found, the display will show “NG”.
2. Press the [STOP/EXIT] button to return to the main screen.
[4]. ROM check
1. Press the numeric button [4] to run this test.
This test automatically performs the ROM check.
If normal, the display will show “OK”. If an error occurs, the
display will show as follows.
· If there is an error on the wave ROM
· If there is an error on the program ROM
· If there is an error on the wave ROM and program ROM
2. Press the [STOP/EXIT] button to return to the main screen.
[5]. MIDI check
1. Before entering this test, connect MIDI IN to OUT using the
MIDI cable.
2. Press the numeric button [5] to run this test.
If the test result is normal the display will show “OK”.
If the test is entered before connecting the MIDI cable, the
display will show “NG”. Connect the MIDI cable properly
and the display will change to “OK”.
3. Press the [STOP/EXIT] button to return to the main screen.
[6]. FSR (key-pads) check
This test checks whether the FSR (key-pads) is functioning.
1. Press the numeric button [6] to run this test.
The display will show as follows:
2 . I n th e“ ” field the key-pad number is displayed, and in
the “ ” field the pressure value is indicated.
An asterisk “*” is displayed when the pressure value reaches
“127”.
When a key-pad is pressed, the red LED first goes on and
then the green LED turns on when the pressure reaches
“127”.
A beep of oscillation sound is output from the OUTPUT-L/R
jacks.
If the FSR pattern touches a key-pad or two key-pads are
pressed simultaneously, the display will show “T” to the right
of the key-pad number as shown in the figure below.
At the same time, the key-pad number being touched will bedisplayed at the lower right of the LCD display.
3. When all the key-pads are pressed with a pressure of more
than 127 and there is no pattern touch in the FSR, the display
will show “OK”. If the pressure value is low or any pattern
touch occurs, the display will show “NG”.
4. Press the [STOP/EXIT] button to return to the main screen.
[7]. Sound checkThis performs the tests for sounding and panning.
1. Press the numeric button [7] to run this test.
The display will show as follows:
K Sounding
2 . I n t he “ ” field the output destination is displayed, and
in the “ ” field the velocitiy is indicated.
3. When you press one of key-pads 1 to 4, sound will be output
as shown in the table below.
Pad no. / 1L
TOM1
2R
TOM2
3IND1
TOM3
Output destination /
Sound /
[3]. RAMチェ ッ ク
1. 数字ボタン [3] を押して、テストを実行させます。
自動的にRA M のチェックを行います。正常ならば、
LC Dディスプレイに、“OK ”と表示され、異常があれ
ば“NG ”と表示されます。
2. [STO P/EX IT] ボタンを押すと、メイン画面に戻りま
す。
[4]. ROMチェッ ク
1. 数字ボタン [4] を押して、テストを実行させます。
自動的にRO M のチェックを行います。正常ならば、
LC Dディスプレイに、“OK ”と表示され、異常があれ
ば以下のように表示されます。
・ W AVE ROM がNG
・ プログラムROM がNG
・ W AV E RO M とプログラムRO M の両方がNG
2. [STO P/EX IT] ボタンを押すと、メイン画面に戻りま
す。
[5]. MIDIチェ ッ ク
1. テストを実行する前に、M ID Iケーブルで、M IDI INと
O U Tを接続します。
2. 数字ボタン [5] を押して、テストを実行させます。
自動的にチェックを行い、正常ならば、LCDディスプ
レイに、“OK ”と表示され、異常があれば“NG ”と表
示されます。
(M ID Iケーブルで、M ID I IN とOU Tを接続しないで、
テストを実行した場合、“NG ”と表示されますが、
M ID Iケーブルで接続すると、“OK ”と表示されま
す。)
3. [STO P/EX IT] ボタンを押すと、メイン画面に戻りま
す。
[6]. FSR( キー・ パッド ) チェック
FSR (キー・パッド)のチェックを行います。
1. 数字ボタン [6] を押して、テストを実行させます。
LC Dディスプレイに、下記のように表示されます。
2. “”に、押したキー・パッドの番号、“”に
は押したときの圧力値が表示されます。“*”は、圧力
値が“127”になると表示されます。
また、キー・パッドを押すと、最初に赤のLED が点灯
し、圧力値が“127”になると緑のLED が点灯します。
O U TPU T-L/R ジャックから、“ピー”という発振音が
出力されます。この時、FSR (キー・パッド)のパター
ンがタッチしていた場合、または、2つのキー・パッド
を同時に押した場合は、下記のように、“T”がキー・
パッド番号の右側に表示されます。同時に、タッチして
いるキー・パッドの番号が、LC Dディスプレイ右下に
表示されます。
3. 全てのキー・パッドが、それぞれ “127” 以上の圧力
値で押され、FSR(キー・パッド)にパターン・タッチ
がなければ、LC Dディスプレイに、“OK ”と表示され
ます。
押したときの圧力値が低かったり、パターン・タッチ
あったときは、“NG”と表示されます。
4. [STO P/EX IT] ボタンを押すと、メイン画面に戻りま
す。
[7]. サウンド・ チェック音出しとパンニングのテストを行います。
1. 数字ボタン [7] を押して、テストを実行させます。
LC Dディスプレイに、下記のように表示されます。
音出し
2. “”は出力ジャック名、“”には押された時
の圧力値が表示されます。
3. キー・パッドの“1”∼ “3”を押すと、それぞれ下表
のように音が出力されます。
パッド番号出力ジャック
出力音
8/3/2019 Boss DR-770 Service Notes
http://slidepdf.com/reader/full/boss-dr-770-service-notes 10/18
DR-770 Feb. 1999
10
K EQ (IC106 on Jack Board)
4. When you press one of key-pads “5” to “7”, a rectangle wave
will be output with following EQ setting.
<Fig 1> L(MONO)
R
Pad No. 5 Pad No. 6 Pad No. 7
K Panning
5. When you press one of key-pads 13 to 15, a sine wave will be
output with the follwing panning.
<Fig 2> L(MONO)
R
Pad No. 13 Pad No. 14 Pad No. 15
6. The LCD is displayed as shown below.
7 . I n t he “ ” field the panning state is displayed, and in the
“ ” field the pressure value is indicated.
An asterisk “*” is displayed when the pressure value reaches
“127”.
When a key-pad is pressed, the red LED first goes on and
then the green LED turns on when the pressure reaches
“127”.
8. When pressing the [STOP/EXIT] button, the display will
show “OK”.
9. Again, press the [STOP/EXIT] button to return to the main
screen.
Pad no. / 5
0dB
0dB
00
6
-12dB
+12dB
+12 -12
7
+12dB
-12dB
-12 +12
EQ High
EQ Low
LCD display /
Pad no. / 13
L7
14
CENTER
15
R7Panning /
(1v/div)
(2ms/div)
(1v/div)
(2ms/div)
EQ (IC106 or Jack Board)
4. キー・パッドの“5”∼ “7”を押すと、それぞれ下表
のようなEQ設定で矩形波が出力されます。
パンニング
5. キー・パッドの“13”∼ “15”を押すと、下表のよう
なパンニングで正弦波が出力されます。
6. L C Dディスプレイには、下記のように表示されます。
7. “”にパンニング状態、“”には押された時
の圧力値が表示されます。“*”は、圧力値が“127”
になると表示されます。
また、キー・パッドを押すと、最初に赤のLED が点灯
し、圧力値が“127”になると緑のLED が点灯します。
8. [STO P/EX IT] ボタンを押すと、LCD ディスプレイに、
“OK ”と表示されます。
9. もう一度、[STO P/EX IT] ボタンを押すと、メイン画面に戻ります。
パッド番号
LCD 表示
パッド番号
パンニング
8/3/2019 Boss DR-770 Service Notes
http://slidepdf.com/reader/full/boss-dr-770-service-notes 11/18
DR-770 Feb. 1999
11
TROUBLESHOOTING
q No sound is produced.
possible causes
The volume is set to minimum.
The level of the key-pads is set to zero.
The selected Rhythm Pattern or Song contains on data.
w Sound breaks.
possible causesMore than 14 voices are being played simultaneously.
Assign Type for the key-pads is not properly set.
e Sound is strange.
possible causes
The settings for the key-pads are inappropriate.
r The Roll/Flam effect is not produced.
possible causes
The Flam Interval is set to zero.
The settings for the Flam Ratio are inappropriate.
t Playback does not begin when [START] button is pressed.
possible causes
The Sync Mode is set to MIDI.
The selected Rhythm Pattern or Song contains no data.
y Songs automatically play one after another.
possible causes
The song chain function is ON.
u The tempo changes when a song starts playing.
possible causes
An internal tempo is being set.
i The DR-770 cannot be controlled by an external MIDI
device.
An external MIDI device cannot be controlled by the DR-770.
possible causes
The MIDI channels of the DR-770 and the external MIDI
device do not match.
Note numbers of the DR-770 and the external MIDI device do
not correspond.
o When the DR-770 is played by performance data from a
sequencer, the song on the DR-770 starts together.
possible causes
The Sync Mode is set to MIDI sync.
!0 The metronome does not sound.
possible causes
The level of the metronome is set to zero.
!1 Program Change messages cannot be transmitted or
received.
possible causes
“4PRG’ in the MIDI Mode is set to OFF.
!2 The volume does not change when MIDI Volume messages
are received.
possible causes
“5RxVOL” in the MIDI mode is set to OFF.
!3 The volume does not change when MIDI Expression
messages are received.
possible causes
“6RxEXPR” in the MIDI mode is set to OFF.
!4 The DR-770 cannot receive Exclusive messages.
possible causes
“7RxEXC” in the MIDI mode is set to OFF.
MIDI channels are not set to the same number.
ト ラブルシューティ ング
q 音が出ない。
原因
ボリュームが最小になっている。
キーパッドのレベルが“0”になっている。
現在選ばれているソング、またはリズム・パターンに
データが記憶されていない。
パンの設定が、“IN D IV”になっている。
w 音が途切れる。
原因同時に14音以上の音色を鳴らしている。
キー・パッドのアサイン・タイプが不適当。
e 音色がおかしい。
原因
キー・パッドの設定が不適当。
r ロール/フラムができない。
原因
ロールの設定で、タイプが“FL”になっている。
フラム・インターバルやフラム・レシオの設定が不適
当。
t [START] ボタンを 押しても 演奏がスタート しな い。
原因
シンク・モードがM ID Iになっている。
現在選ばれているソングまたはリズム・パターンにデー
タが記憶されていない。
y ソングの演奏が終了したら 、 他のソングが自動的にス
タートす る 。
原因
ソング・チェインが設定されている。
u ソングの演奏をスタートすると、 テンポが変化する。
原因
イニシャル・テンポが設定されている。
i 外部MIDI機器から 音が鳴ら せない。
外部MIDI機器の音が鳴らな い。
原因M ID Iチャンネルが合っていない。
ノート・ナンバーが合っていない。
o シーケンサーの演奏データでDR-770を鳴ら す時に、 DR-
770のソングが一緒にスタート する。
原因
シンク・モードがM ID Iになっている。
!0 メト ロノ ーム が鳴らな い。
原因
メトロノームのレベルが“0”になっている。
!1 プログラム・ チェンジが送受信されない。
原因
M ID Iモードの“4PRG ”がOFFになっている。
!2 MIDIボリ ューム 情報で音量が変化しない。
原因
M ID Iモードの“5RxV O L”がOF Fになっている。
!3 MIDIエクスプレ ッ ショ ン情報で音量が変化しない。
原因
M ID Iモードの“6RxEX PR”がOFFになっている。
!4 エクスクルーシブ・ メッ セージを受信しない。
原因
M ID Iのモードの“7RxE X C”がO FFになっている。
M IDIチャンネルが合っていない。
8/3/2019 Boss DR-770 Service Notes
http://slidepdf.com/reader/full/boss-dr-770-service-notes 12/18
DR-770 Feb. 1999
12
ERROR MESSAGE
If you attempt an incorrect operation or if an operation could not be
executed, the display will indicate an error message. Refer to this
list and take the appropriate action.
q No more patterns can be recorded. Press [STOP/EXIT]. If you want to continue recording patterns,
you must first delete unneeded patterns. (p. 62)
q No more songs can be recorded.
Press [STOP/EXIT]. If you want to continue recording songs,
you must first delete unneeded songs. (p. 67)
q During pattern editing, using “Copy Pattern” or “Delete
Pattern,” the selected pattern contained no data.
Press [STOP/EXIT], then select a different pattern.
q During song editing, using “Insert Pattern” or “Delete Pattern,”
the selected pattern contained no data.
Press [STOP/EXIT], then select a different part.
q During song editing, using “Copy Song” or “Delete Song,” the
selected song contained no data.
Press [STOP/EXIT], then select a different song.
q An excessive amount of MIDI data was received all at once, and
the DR-770 was unable to process it.
Press [STOP/EXIT],
If this message appears while receiving data, reduce the amount
of MIDI data that is being transmitted to the DR-770.
Change the MIDI mode setting so unnecessary MIDI messages
are not transmitted or received. (p. 87)
q An exclusive message could not be received correctly.
Press [STOP/EXIT], then try the operation once again.
q The memory backup battery inside the DR-770 has run down.
(This message will appear when the power is turned on.)
Replace the battery as soon as possible. For battery
replacement, please contact a Roland Service Center.
q The data in internal memory has been lost. (This message will
appear when the power is turned on.)
After this message is shown, “Press ENTER” appears, then
pressing [ENTER] will recall the factory settings.
/エラ ー・ メ ッ セ ージ
操作を誤ったり、正しく実行できなかったときは、ディスプ
レイにエラー・メッセージが表示されます。表示のメッセー
ジにしたがって対処してください。
q パターンをこれ以上記憶することはできません。 [STO P/EX IT]を押してください。パターンの録音を続
ける場合は、不要なパターンを削除してください。
(P.62)
q ソングをこれ以上記憶することはできません。
[STO P/EX IT]を押してください。ソングの録音を続け
る場合は、不要なソングを削除してください。(P.67)
q パターン編集の「パターンのコピー」や「パターンの削
除」で、対象となるパターンにデータがありません。
[STO P/EX IT]を押してから、パターンを替えてくださ
い。
q ソング編集の「パターンの挿入」や「パターンの削除」
で、対象となるパターンにデータがありません。
[STO P/EX IT]を押してから、パートを替えてくださ
い。
q ソング編集の「ソングのコピー」や「ソングの削除」
で、対象となるソングにデータがありません。
[STO P/EX IT]を押してから、ソングを替えてくださ
い。
q 大量のM IDI情報を受信したため、DR -770本体で処理しき
れなくなりました。
[STO P/EX IT]を押してから、
受信時に表示されたときは、送信側のM ID I情報を減らし
てください。
不必要なM ID I情報を送受信しないように、M ID Iモードの
設定を行ってください。(P.87)
q エクスクルーシブ・メッセージが正しく受信できません
でした。
[STO P/EX IT]を押してから、もう一度操作をやり直し
てください。
q 本体のメモリー・バックアップ用の電池が消耗していま
す。(このメッセージは、電源投入時に表示されま
す。)
早めに電池を交換してください。交換に関しては、ロー
ランド・サービスにご相談ください。
q 本体に記憶されているデータが壊れています。(この
メッセージは、電源投入時に表示されます。) このメッセージが表示された後“Press EN TE R”と表示さ
れ、[EN TE R]を押すと、製品出荷時の設定に戻ります。
8/3/2019 Boss DR-770 Service Notes
http://slidepdf.com/reader/full/boss-dr-770-service-notes 13/18
DR-770 Feb. 1999
13
BLOCK DIAGRAMA
B
C
D
EF
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
/ブ ロ ッ ク 図
8/3/2019 Boss DR-770 Service Notes
http://slidepdf.com/reader/full/boss-dr-770-service-notes 14/18
DR-770 Feb. 1999
14
A
B
C
D
EF
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
CIRCUIT DIAGRAM (JACK)
IND1
L/MONO
R
PH O N ES
AC 1 4 V
To Main Board
CN2
To Main Board
CN1
MIDI INMIDI O UT
FOOT SWITCH
ENC Board
VR Board
To ENC Board
CN201
To VR Board
CN301
To Jack Board
CN 103
To Jack Board
CN 101
Jack Board
A
A
A
A
A
A A
A
D
A A
A
A
A
V RE F 4 .0 V
V RE F 4 .0 V
V RE F 4 .0 V
A
D
D
A A
+5D
+5D +5D
+5D
A +8
A
A +8
A
A +8
A
V RE F 4 .0 V
D
DD
D
D
D
A +8
A
+5D
+5D
A
V RE F 4 .0 V
A
A
A
A +9
+5D
D
A
A
A
V RE F 4 .5 V
D
V RE F 4 .0 V
A
A
A
D
D A
A
C1 1 51 0 /1 6
L 1 0 6S B T- 0 4 6 0
R1 2 72 2 ( 1 /2 W)
C1 3 34 7 /1 6
L 1 0 7S B T- 0 4 6 0
C1 2 84 7 /1 6
R1 3 22 2 ( 1 /2 W)
Q 1 0 1DTC3 4 3 TK
1
2
3
Q 1 0 3DTC3 4 3 TK
1
2
3
L 1 0 3S B T- 0 4 6 0
Q 1 0 2DTC3 4 3 TK
1
2
3
C1 2 7
0 .0 0 3 3
C1 1 9
0 .0 0 3 3
L 1 0 5S B T- 0 4 6 0
L 1 0 4S B T- 0 4 6 0
C1 0 11 0 /1 6
C1 1 41 0 /1 6
R1 0 710k
C1 1 0
1 5 0 p
R1 2 6
56k
CN3 0 1
WIRING HA RNE S S C
11
22
33
44
55
66
C1 1 8150p
C1 1 7
1 5 0 p
+
-
IC1 0 2 BUP C4 5 7 06
57
C1 2 0
0 .0 3 3
CN2 0 1
WIRING HA RNE S S B
11
22
33
R1 2 51k
C1 2 6150p
R1 1 8
56k
R1 1 03 .3 k
C1 2 31 0 /1 6
JK 1 0 6
HE C0 7 4 0 - 0 1 0 - 1 0
213
+
-
IC1 0 1 AUP C4 5 7 0
2
31
CN1 0 35 3 2 5 4 - 0 3 1 0 ( 3 P )
11
22
33
R1 1 318k
C1 2 21 0 /1 6
C1 0 81 0 /1 6
L 1 1 0 S B T- 0 4 6 0
C1 2 12 .2 /2 5
R1 2 43 .3 k
R1 1 9
56k
C1 1 2
0 .0 3 3
C1 2 5
1 5 0 p
R1 1 63 .3 k
R1 1 53 .3 k
R1 1 71k
C1 0 61 0 0 p
R1 2 33 .3 k
L 1 0 9 S B T- 0 4 6 0
C1 0 7
0 .0 3 3
R1 0 93 .3 k
R1 1 11k
L 1 1 1 S B T- 0 4 6 0
R1 2 0
56k
JK 1 0 5
Y K B 2 1 - 5 1 3 0
1
23
CN1 0 1
5 3 2 5 4 - 0 6 1 0 ( 6 P )
11
22
33
44
55
66
R1 1 2
56k C1 1 1
0 .0 0 3 3
L 1 0 2S B T- 0 4 6 0
R1 0 51k
R1 3 4
3 .3 k
R1 0 618k
R1 0 210k
C1 3 5
0 .0 0 3 3
R1 2 8
3 .3 k
R1 0 31k
R1 0 410k
C1 3 2
0.1
C1 3 1
0.1
C1 3 0
0.1
A B
ENE N2 0 1 AE C1 6 B 2 4 2 0 4
3 1 2
A B
EN
E N2 0 1 BE C1 6 B 2 4 2 0 4
1
0
2
0+
-
IC1 0 1 BUP C4 5 7 0
6
57
+
-
IC1 0 3 AM5 2 1 6 FP2
31
+
-
IC1 0 3 BM5 2 1 6 FP6
57
+
-
IC1 0 2 AUP C4 5 7 02
31
C1 0 4
1 0 0 p
C1 0 5
100p
C1 0 2
1 0 0 p
C1 0 3
100p
L 1 1 7
S B T- 0 1 6 0 W
1
2
4
3
D1 0 7
1 S S 1 3 3
1
2
D1 0 6
1 S S 1 3 3 1
2
D1 0 4
1 S S 1 3 3 1
2
D1 0 5
1 S S 1 3 3 1
2
C1 5 0
0 .4 7
C1 4 72 .2 /2 5
C1 4 9
0 .0 2 2
C1 4 8
0 .0 2 2
C1 5 1
0 .4 7
C1 4 62 .2 /2 5
R1 2 118k
C1 1 32 .2 /2 5
C1 5 2
0.1
IC1 0 6
M6 2 4 2 1 S P
A G ND13
CH1 IN2
S IMIN13
S IMO UT14
B A S S 15
DV DD12
O UT17
AVDD20
DG ND8
REF1
CS11
DAT9
CLK10
O UT214
TRE 215
B A S S 216
S IMO UT217
S IMIN218
CH2 IN19
TRE 16
CN1 0 4
WIRING 6 P
11
22
33
44
55
66
CN1 0 2
WIRING 1 1 P
11
22
33
44
55
66
77
88
99
1010
1111
1
42
5
3
JK 1 0 8M- S 2 - 3 P
5 2 4
JK 1 0 1
HL J7 0 0 1 - 0 1 - 3 0 1 0
1
34
JK 1 0 2
HL J7 1 0 1 - 0 1 - 3 0 1 0
1
34
JK 1 0 3
HL J7 1 0 1 - 0 1 - 3 0 1 0
1
2, 34
JK 1 0 4
HL J7 1 0 1 - 0 1 - 3 0 1 0
1
2, 34
V R3 0 1 BRK 1 4 K 1 2 4 5 0 kB *2
1
4
6
V R3 0 1 ARK 1 4 K 1 2 4 5 0 kB *2
2
3
5
V R3 0 1 CRK 1 4 K 1 2 4 5 0 kB *2
1 0
2 0
1
42
5
3
JK 1 0 7M- S 2 - 3 P
5 2 4L 1 0 8 S B T- 0 4 6 0R 1 44 1 0 0
R 1 45 1 2 0
R 1 46 2 2 0
R 1 47 2 2 0
C1 2 9
0 .0 0 3 3
C1 5 5 0 .0 3 3
C1 5 6 0 .0 3 3
S W1 0 1 A
S P UN1 9 4 3 0 A
3.62, 5
+ -
~
~
D1 0 2
1 G 4 B 4 2 2
1
4 3
+
-
IC1 0 1 CUP C4 5 7 0
8
4
+
-
IC1 0 2 CUP C4 5 7 0
8
4
+
-
IC1 0 3 CM5 2 1 6 FP
8
4
C1 5 3
0.1
R1 2 910k
C1 5 4
4 7 0 /1 6
C1 3 6
4 7 0 /2 5
C1 4 30.1
D1 0 1
MTZ8 .2 B
1
2
R1 3 5
560
R1 0 1
56k
D1 0 3
MTZ5 .6 C 1
2
Q 1 0 6
2 S C2 4 5 9
3
1
2
R1 3 110k
R1 3 7
1 5 ( 5 W)
IC1 0 5
UP C2 4 M0 9 A HF
IN1
OUT3
C O M
2C1 4 2
1 0 0 /1 6
R1 4 2
4 .7 k
Q 1 0 4
2 S A 1 0 4 9
3
2
1
C1 3 8
1 0 0 /6 .3 C1 3 90.1
R1 4 3
4 .7 k
C1 3 7
4 7 0 /2 5
Q 1 0 5
2 S C2 4 5 9
3
1
2
R1 3 310k
R1 3 047k
C1 3 4
4 7 /1 6
C1 4 40.1
C1 4 00.1
R1 3 65 .6 ( 3 W)
L 1 0 1S B T- 0 4 6 0
C1 5 80.1
C1 5 71 0 0 p
C1 5 91 0 0 p
C1 6 0
0.1
C1 6 11 0 0 p
C1 6 2
1 0 0 p
IC1 0 4
7 8 0 5 A HF
IN 1OUT3
C O M
2
C1 6 3
1 0 /3 5
R1 3 9
1k
R1 3 80 ( JUMP E R)
To Main Board(1/2)
CHORUS
RE V E RB
DRUM KIT
TEMPOSTEP/REAL
ROL LPTN/SONGPAD
EFFECT
7
8
9
4
5
63
2
1
MIDI
UTILITYCOP Y
DELETE
V(down)
0
^(up)ENTER
FWD
>(right)BWD
<(left)RESET
PAD BA NKFLAMREC
STAR T
STOP/EXIT
Main Board(2/2)
DA4
1SS300
1 2
DA7
1SS300
1 2
SW12
1 2
DA 1 1
1SS300
1 2
DA 1 5
1SS300
1 2
SW5
1 2
SW20
1 2
SW28
1 2
SW36
1 2
SW35
1 2
SW27
1 2
SW19
1 2
SW11
1 2
SW4
1 2
SW3
1 2
SW2
1 2
DA3
1SS300
1 2
DA6
1SS300
1 2SW10
1 2
SW9
1 2
SW17
1 2
DA 1 0
1SS300
1 2
SW18
1 2
SW25
1 2
DA 1 4
1SS300
1 2
SW26
1 2
SW33
1 2
SW34
1 2
SW1
1 2
DA2
1SS300
1 2
DA5
1SS300
1 2
SW8
1 2
SW15
1 2
DA9
1SS300
1 2
SW16
1 2
DA13
1SS300
1 2
SW23
1 2
SW24
1 2
SW31
1 2
SW32
1 2
SW6
1 2
SW7
1 2
SW30
1 2
SW22
1 2
SW14
1 2
SW29
1 2
SW21
1 2
SW13
1 2
DA18
1SS300
1 2
DA 1 7
1SS300
1 2
DA 1 6
1SS300
1 2
DA 1 2
1SS300
1 2
DA8
1SS300
1 2
DA 1 9
1SS300
1 2
P0P1P2P3P4P5P6P7P8P9P10P11P12
/回路図 (JACK)
8/3/2019 Boss DR-770 Service Notes
http://slidepdf.com/reader/full/boss-dr-770-service-notes 15/18
DR-770 Feb. 1999
15
A
B
C
D
EF
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
CIRCUIT BOARD (JACK)
View from component side.
/基板図 (JACK)
8/3/2019 Boss DR-770 Service Notes
http://slidepdf.com/reader/full/boss-dr-770-service-notes 16/18
DR-770 Feb. 1999
16
CIRCUIT DIAGRAM (MAIN)A
B
C
D
EF
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
To Main Board(2/2)
To Jack BoardCN104
To Jack BoardCN102
To FSR(Key-Pads)
Main Board(1/2)
P9
P5
P10
P8
P6
P11
P4
P7
P11P10
P7
P4
P8
P2
P12
P9
P5P6
P[12..0]
P1P0
P3P2
P1P0
P3
P5
P10P9
P6P7
P11
P8
P12
F1
F15
F13
F7
F8
F15F13
F6
F6
F14
F4
F1
F5
F12F15
F10
F13
F6
F9F10
F6F5
F8
F7
F3
F14
F3
F1
F10
F10
F2
F3
F4F3
F12
F7
F16
F11
F9
F12
F5
F8
F13
F9
F14
F7 F2
F11
F14
F5
F15
F2
F8F4
F12
F2F1
F11
F9
F4
P12
F11
F16 F16
F16
F[16..1]
WD2
WD0WD1
WD3
WD5WD7
WD4
WD1
WD[7..0]WD7
WD0
WD4
WD2
WD6
WA21
WD3
WD6WD5
WD6WD7
WD0
WD2WD1
WD5WD4WD3
WA21
WA19
WA10WA9
WA5
WA3
WA17
WA8
WA14
WA19
WA12
WA13
WA9
WA2
WA18
WA1
WA10
WA[21..0]
WA4
WA2
WA6
WA15
WA14
WA7
WA11
WA15
WA0
WA7
WA20
WA20
WA4
WA16
WA16
WA1
WA6
WA0
WA13
WA17
W A1 8 W A1 1
WA12
WA8
WA5
WA3
A2
A16A16
A1
A7
A14
A19
A11
A5
A5
A14
A1
A18
A4
A4
A0
A16
A1
A18
A7
A21
A10
A17
A8
A7
A9
A18
A4
A2
A20
A6
A4A3
A3
A11
A9
A12
A2
A3
A3
A0
A[21..0]
A5
A6
A13A10
A10
A14
A6
A21
A19
A5
A12
A15
A15
A15
A13
A17
A8
A20
A0
A0
A8
A11
A2
A9
A12
A13
A0
A1
A20
A19
A17
D[7..0]
D2
D4D5
D0
D7
D0
D3
D1
D2
D3D2
D3
D7
D5
D1
D4
D6
D7
D7
D5
D[7..0]
D6
D0
D0
D4
D6
D0
D4
D1D2
D2
D3
D4
D6D5
D1
D0
D5
D5
D1
D3
D7
D1
D6
D7
D3
D4
D6
D2
ED5
ED7
ED5
ED[7..0]
ED2
ED6
ED7
ED1
ED0
ED6
ED2
ED2
ED0
ED1
ED3
ED1ED4
ED4
ED4
ED7
ED5
ED6
ED4
ED1
ED3
ED3
ED7
ED6
ED0
ED5
ED0
ED3
ED2
+5D
D
D
+5D
+5D
D
+ 5D
+ 5D
D
+5D
D
A
B A T
D
D
D+5D
+5D
+ 5D
D
+5D
D
A
D
D
A
B A T
D
D
+ 5D
D
D
+5D
+5D
D
D
+5D
D
+ 5D
+ 5D
D
D
+5D
D
D
D
D
DD
+ 5D
D
+ 5D
D
+5D
A
D
D
D
D
+ 5D
D
A
+ 5D
D
+5D
+ 5D
D
D
+5D
D
D
D
+5D
+ 5D
D
D
D
D
D
D
D
D
+ 5D
D
B A T
+5D
D
+5D
+5D
+5D
+5D
+5D
+ 5D
+5D
+5D
+ 5D
+5D
+ 5D
+5D
D
A
+ 5D
D
D
+ 5D
C2 0. 1
C22
47/10
IC17TC74AC138F
C3
B2
A1
G2B5
G2A4
G16
Y7 7
Y69
Y510
Y411
Y312
Y2 13
Y114
Y015
V C C
1 6
G N D
8
C21
0.1
R17
220
IC8LH53H4100
A1831
A1730
A162
A153
A1429
A1328
A124
A1125
A1023
A926
A827
A75
A66
A57
A48
A39
A210
A111
A012
CE22
OE24
D721
D620
D519
D418
D317
D215
D114
D013
VPP1
VCC32
VSS16
IC2FTC74AC14AF
1312
R1133k
C4 0. 1
C250.1
R14
2.2M
IC18TC7S02F1
24
5
3
C5 0. 1
C6 0. 1
IC15BU9480F
V C C
8
G N D
3
LRCK5
BCLK7
SDAT6
LOUT4
ROUT1
REF2
BT1
(CR2032) 1
2
C1347/16
IC2ATC74AC14AF
12
R1210k
R7100k
R29180
R25
2.2k
IC9
SED1278F0A
SEG4063
SEG3964
SEG3865
SEG3766
SEG3667
SEG3568
SEG3469
SEG3370
SEG3271
SEG3172
SEG3073
SEG2974
SEG2875
SEG2776
SEG2677
SEG2578
SEG2479
SEG2380
SEG221
SEG212
SEG203
SEG194
SEG185
SEG176
SEG167
SEG15 8
SEG149
SEG1310
SEG1211
SEG1112
SEG10 13
SEG914
SEG815
SEG716
SEG617
SEG5 18
SEG419
SEG320
SEG221
SEG122
COM1662
COM1561
COM1460
COM1359
COM1258
COM1157
COM1056
COM955
COM854
COM753
COM652
COM551
COM450
COM3
49
COM2 48
COM147
DB746
DB645
DB544
DB443
DB342
DB241
DB140
DB039
LP31
XSCL32
FR 34DO 35
RS36
R/W37
E38
OSC124
OSC225
V530
V429
V328
V227
V126
VDD33
VSS23
R27
2.2k
R22
91k
R24
2.2k
R16
220
R26
2.2k
R23
2.2k
IC3ATC7WU04F1 7
C18
100/6.3
IC20M51954BFP
R S T
6
DLY5
VCC7
GND4
NC1
NC2
NC3
NC8
C61
1/50
R39
10k
R10
22k
X1MA-406 24MHz
1 4
IC3CTC7WU04F6 2
R33
220
R281M
IC13TC74HC4052
3Y4
2Y2
1Y5
0Y1
3X11
2X15
1X14
0X12
YCOM3
XCOM13
INH6
B9
A10
VEE7
VCC16
GND8
IC114HC4052
3Y4
2Y2
1Y5
0Y1
3X11
2X15
1X14
0X
12
YCOM3
XCOM13
INH6
B9
A10
VEE7
VCC16
GND 8
LED2SLC-22MG
12
LED1SLC-22VR
12
R6330
R8270
LCD1
RCD1627R
SEG401
SEG392
SEG383
SEG374
SEG365
SEG356
SEG347
SEG338
SEG329
SEG3110
SEG3011
SEG2912
SEG2813
SEG2714
SEG2615
SEG2516
SEG2417
SEG2318
SEG2219
SEG2120
SEG2021
SEG1922
SEG1823
SEG1724
SEG1625
SEG1526
SEG1427
SEG1328
SEG1229
SEG1130
SEG1031
SEG932
SEG833
SEG734
SEG635
SEG536
SEG437
SEG338
SEG239
SEG140
COM1641
COM1542
COM1443
COM1344
COM1245
COM1146
COM1047
COM453
COM948
COM849
COM750
COM651
COM552
COM3
54
COM255
COM156
R15
220
R4100k
IC1ABA10393F
3
21
C1
0.1
IC1CBA10393F
8
4
IC2G
TC74AC14AF
1 4
7
IC3DTC7WU04F
8
4
C3
0.1
C44220p
C41220p
C47220p
C38
220p
C53220p
C32220p
C50220p
C34220p
C31220p
R 34 1 k
IC16BU9480F
V C C
8
G N D
3
LRCK5
BCLK7
SDAT6
LOUT4
ROUT1
REF2
R 35 1 k
R 32 1 k
C58
47/10
C55
0.1
IC2CTC74AC14AF
56
CN3
11
22
33
4455
66
77
88
9 910 1011
1112
1213
1314 1415
1516
1617
17
R40
1k
R4110k
R20 1k
R 19 1k
R18 1k
R45100
C57
22P
C16
0.1
C7
0.1
IC4
LH5332P00N
A2044
A1943
A182
A173
A1634
A1535
A1436
A1337
A1238
A1139
A1040
A941
A842
A74
A65
A56
A47
A38
A29
A110
A011
*/D1531
BYTE33
CE12
OE14
D1429
D1327
D1225
D1122
D1020
D918
D816
D730
D628
D526
D424
D321
D219
D117
D015
NC1
VCC23
VSS13
VSS32
IC12
TC551001CF-70L
A162
A1531
A143
A1328
A124
A1125
A1023
A926
A827
A7
5
A66
A57
A48
A39
A210
A111
A012
CE230
CE122
R/W29
OE24
I/O821
I/O720
I/O619
I/O518
I/O417
I/O315
I/O214
I/O113
NC1
VDD32
VSS16
R1
10k
IC14TC7S04F
2 4
5
3
C52220p
C37220p
C14
0.1
C40220p
C33220p
C20
0.1
C43220pC46220pC49220p
C11
0.01
C62
0.1
C56
22P
C10
0.01
R9
47k
IC3BTC7WU04F3 5
DA1RB715F
1 2
3
RA1RCE9A1031 2
3456789
RA3
RCE9A103
1 23456789
RA4
RCE9A223
123456789
R3
100k
R36
33k
C17
0.1
C9
0.1
C12
0.1
C15
0.1
C39
0.1
C260.1
C8
0.1
R5
100k
R37
4.7k
R21
1k
RA2RCE9A103
1 23456789
RA5CNB2B9Z3.3K
1 23456789
RA6CNB2B9Z3.3K
1 23456789
RA7
EXBV8V103
1 82 73 64 5
IC5TC6116AF
V D D
1 8
V D D
5 4
V D D
9 0
V D D
1 2 6
G N D
1 9
G N D
5 5
G N D
9 1
G N D
1 0 4
G N D
1 2 7
G N D
1 4 2
XMSF114
X68113
XE112
CA1966
CA1867
CA1769
CA1668
CA1570
CA1471
CA1374
CA1273
CA1176
CA1080
CA575
CA477
CA379
CA281
CA184
CA086
CD785
CD687
CD589
CD493
CD395
CD294
CD192
CD088
RESET99
ALE100
DS(RD)78
R/W(WR)72
CS97
WAIT102
GPINT107
EXWAIT115
INT5111
INT4110
INT3109
INT2108
GAINT101
CS7116
CS698
CS582
CS483
CS3118
CS2117
CS152
CS096
RSCD53
RWWR56
LERD57
LD765
LD664
LD563
LD462
LD361
LD260
LD159
LD058
IOCK103
CK105
SC546
SC447
SC348
SC249
SC150
SC051
TEST106
WA19134
WA18135
WA17137
WA16136
WA15138
WA14139
WA13141
WA12140
WA114
WA107
WA92
WA8144
WA7143
WA61
WA53
WA45
WA36
WA28
WA19
WA011
WD710
WD612
WD514
WD416
WD320
WD217
WD115
WD013
WCS7133
WCS6132
WCS5131
WCS4130
WCS3129
WCS2128
WCS1125
WCS0124
EA1445
EA1342
EA1243
EA1136
EA1033
EA938
EA840
EA741
EA639
EA5
37
EA4 35
EA334
EA232
EA130
EA028
ED729
ED627
ED525
ED423
ED321
ED222
ED124
ED026
EWE44
ECS31
SD119
SCK121
DACA(LE)120
DACC(MX)122
DACB(INH)123
IC19MB622928PF-G-BND
EWE1
ED02
ED13
ED24
CK5
V S S
6
RESET7
NC8
SD9
SCK10
LE11 V
D D
1 2
WDTH013
WDTH114WDTH215
CC16 CR17
V S S
1 8
ED319
ED420
ED521
ED622
ED723
V D D
2 4
C66
27p
DA201SS300
1 2
3
R44100
IC6HD6415108F
P32/BREQ49
STBY112
MD2111
MD1110
MD0109
TXD2/P8796
RXD2/P8695
TXD1/P8594
RXD1/P8493
P6780
P6679
P6578
P6477
P6376
P6275
P6174
P6073
P5772
P5671
P5570
P5469
P53/FTOB268
P52/FTOA267
P51/FTOB166
P50/FTOA165
AN3/P7386
AN2/P7285
AN1/P7184
AN0/P7083
AVCC87
AVSS82
SCK2/IRQ3/P8392
SCK1/IRQ2/P8291
P81/IRQ190
P80/IRQ089
P3754
P3653
P3552
P34
51
P3350
EXTAL98
XTAL99
NMI2
P47/FTCI263
P46/FTI262
P45/FTCI161
P44/FTI160
P43/TMO59
P42/TMRI58
P41/TMCI57
P40/ADTRG56
P27/A2345
P26/A2244
P25/A2143
P24/A2042
P23/A1941
P22/A1840
P21/A1739
P20/A1638
A1536
A1435
A1334
A1233
A1132
A1031
A930
A829
A728
A627
A526
A425
A324
A223
A122
A021
D1519
D1418
D1317
D1216
D1115
D1014
D913
D812
P17/D711
P16/D610
P15/D59
P14/D48
P13/D37
P12/D26
P11/D15
P10/D04
RFSH107
RD
104
HWR105
LWR106
AS 103
RES1
P31/BACK48
P30/WAIT47
E102
PHAI101
V C C
5 5
V C C
8 8
V C C
1 0 8
V S S
3
V S S
2 0
V S S
3 7
V S S
4 6
V S S
6 4
V S S
8 1
V S S
9 7
V S S
1 0 0
CN1
53253-0610
11
22
33
44
55
66
R47
100
R49
10k
IC7PC410
6
4
1
35
Q2
DTA114TK
2
3
1
Q1
DTA114TK
2
3
1
Q3
2SA1037KR
2
3
1
IC2ETC74AC14AF
1110
IC2BTC74AC14AF
34
IC2D
TC74AC14AF
9 8
C67
0.1
C680.1
IC10
TC55257DFL-55L
A141
A1326
A122
A1123
A1021
A924
A825
A73
A64
A5
5
A46
A37
A28
A19
A010
CS20
WE27
OE22
I/O819
I/O718
I/O617
I/O516
I/O415
I/O313
I/O212
I/O111
VCC28
VSS14
C65
10p
R13100k
IC1B
BA10393F
5
67
C64
10p
CN2
IL-Z-11PL-SMTY
11
22
33
44
55
66
77
88
99
1010
1111
MIDI IN 2
MIDI OUT 2
MIDI IN 1
ENCORDER B
MIDI OUT 1
P12
P7
P0
P2
P11
P5
P8
P6
P3P4
P9
P1
P10
MIDI OUT 2MIDI OUT 1
MIDI IN 2MIDI IN 1
ENCODER BENCODER A
ENCORDER A
FS0FS1
FS1FS0
/回路図 (MAIN)
8/3/2019 Boss DR-770 Service Notes
http://slidepdf.com/reader/full/boss-dr-770-service-notes 17/18
DR-770 Feb. 1999
17
A
B
C
D
EF
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
CIRCUIT BOARD (MAIN)
View from component side.
/基板図 (MAIN)
DR 770 F b 1999
8/3/2019 Boss DR-770 Service Notes
http://slidepdf.com/reader/full/boss-dr-770-service-notes 18/18
DR-770 Feb. 1999
18
Change Information
The wiring differs depending on the serial number (the location of
the red wire is opposite). The difference between before and after
the change is as follows.
Before change
Applicable serial numbers: ZL90100 ~ ZL90199
Applicable parts #******* WIRING 11p
Wire color: red white - white
Figure 1
The connection method is as follows.
Jack board Main board
1CN102
11
1
CN2
11
No.11 of CN102 is red No.11 of CN2 is red
Figure 2
After change
Applicable serial numbers: ZL90200 ~
Applicable parts #01898989 WIRING W11
Wire color: white - white red
Figure 3
The connection method is as follows.
Jack board Main board
1CN102
11
1
CN2
11
No.1 of CN10 is red No.1 of CN2 is red
Figure 4
There is no difference in the circuit board before or after the change.
As parts for servicing, only the newer wiring (01898989 WIRING
W11) is supplied.
The jack board supplied for servicing has the newer wiring.
The older wiring was installed only on the first production lot of one
hundred units (ZL90100 ~ ZL90199).
• If you replace the jack board wiring with the newer version
(01898989 WIRING W11) on a unit with a serial number
ZL90100 ~ ZL90199, make connections using the newer
method (figure 4).
• If you retain the existing jack board and replace only the main
board of a unit with a serial number ZL90100 ~ ZL90199, makeconnections using the older method (figure 2).
• If you retain the existing main board and replace only the jack
board on a unit with a serial number ZL90100 ~ ZL90199, make
connections using the newer method (figure 4).
/変更案内
ワイヤリングがシリアル番号により異なります(赤線の位置
が逆)。なお変更前、変更後の相違点は以下のとおりです。
変更前
対象シリアル番号.ZL 90100∼ ZL 90199
対象パーツ #******** W IRING 11P
線色:赤白 ー 白
図 1
接続方法は以下のとおりです。
ジャックボード メインボード
C N 102の11番が赤 C N 2の11番が赤
図 2
変更後
対象シリアル番号Serial N o. ZL 90200∼
対象パーツ #01898989 W IRING W 11
線色:白 ー 白赤
図 3
接続方法は、以下のとおりです。
ジャックボード メインボード
C N102の1番が赤 C N2の1番が赤
図 4
なお、変更前と変更後での基板の違いはありません。
サービス用のパーツとしては変更後のワイヤリング
(01898989 W IRING W 11)のみの供給となります。
またサービス用で供給されるジャックボードは、変更後のワ
イヤリングが実装されています。
変更前のワイヤリングは1ロット生産分(ZL 901 00∼
ZL90199)の100台のみに実装されています。
・ シリアル番号.ZL 90100∼ ZL 90199の製品で、ジャックボード
のワイヤリングを変更後のワイヤリング(01898989
W IRING W 11)に交換する場合は変更後の接続方法(図4)
のように接続して下さい。
・ シリアル番号.ZL 90100∼ ZL 90199の製品で、ジャックボード
はそのままで、メインボードのみを交換する場合は、変更前の接続方法(図2)のように接続して下さい。
・ シリアル番号.ZL 90100∼ ZL 90199の製品で、メインボードは
そのままでジャックボードのみ交換する場合は変更後の接続
方法(図4)のように接続して下さい。