Book Heat and Mass Transfer Heat-5 CH7-1
-
Upload
laura-arriaga -
Category
Documents
-
view
20 -
download
0
Transcript of Book Heat and Mass Transfer Heat-5 CH7-1
![Page 1: Book Heat and Mass Transfer Heat-5 CH7-1](https://reader035.fdocuments.us/reader035/viewer/2022062517/55cf9ac0550346d033a3391a/html5/thumbnails/1.jpg)
# 1
Heat Transfer Su Yongkang
School of Mechanical Engineering
HEAT TRANSFER
CHAPTER 7
External flow
![Page 2: Book Heat and Mass Transfer Heat-5 CH7-1](https://reader035.fdocuments.us/reader035/viewer/2022062517/55cf9ac0550346d033a3391a/html5/thumbnails/2.jpg)
# 2
Heat Transfer Su Yongkang
School of Mechanical Engineering
External Flow: Flat Plate
Topic of the Day
![Page 3: Book Heat and Mass Transfer Heat-5 CH7-1](https://reader035.fdocuments.us/reader035/viewer/2022062517/55cf9ac0550346d033a3391a/html5/thumbnails/3.jpg)
# 3
Heat Transfer Su Yongkang
School of Mechanical Engineering
External Flow: Flat Plate
Where we’ve been ……• General overview of the convection transfer
equations.• Developed the key non-dimensional parameters
used to characterize the boundary layer flow and convective heat and mass transfer.
Where we’re going:• Applications to external flow
– Flat plate Today– Other shapes Next time
Then onto internal flow ……
fk
LhNu
![Page 4: Book Heat and Mass Transfer Heat-5 CH7-1](https://reader035.fdocuments.us/reader035/viewer/2022062517/55cf9ac0550346d033a3391a/html5/thumbnails/4.jpg)
# 4
Heat Transfer Su Yongkang
School of Mechanical Engineering
Differences between external and internal flow
• External flow: Boundary layer develops freely, without constraints
• Internal flow:Boundary layer is constrained and eventually merges
![Page 5: Book Heat and Mass Transfer Heat-5 CH7-1](https://reader035.fdocuments.us/reader035/viewer/2022062517/55cf9ac0550346d033a3391a/html5/thumbnails/5.jpg)
# 5
Heat Transfer Su Yongkang
School of Mechanical Engineering
How this impacts convective heat transfer
• Recall the boundary layer convection equations:
• As you go further from the leading edge, the boundary layer continues to grow. Assuming the surface and freestream T do not change:with increasing distance ‘x’:– Boundary layer thickness, ,
– so
– and
fluid thermal conductivity
wall temperature gradient
TTs
Also
0
y
fs y
Tkq
0
yy
T
sq
![Page 6: Book Heat and Mass Transfer Heat-5 CH7-1](https://reader035.fdocuments.us/reader035/viewer/2022062517/55cf9ac0550346d033a3391a/html5/thumbnails/6.jpg)
# 6
Heat Transfer Su Yongkang
School of Mechanical Engineering
Methods to evaluate convection heat transfer
• Empirical (experimental) analysis– Use experimental measurements in a
controlled lab setting to correlate heat and/or mass transfer in terms of the appropriate non-dimensional parameters
• Theoretical or Analytical approach– Solving of the boundary layer equations for
a particular geometry.– Example:
• Solve for T*• Use evaluate the local Nusselt number, Nux
• Compute local convection coefficient, hx • Use these (integrate) to determine the
average convection coefficient over the entire surface
– Exact solutions possible for simple cases. – Approximate solutions also possible using
an integral method
![Page 7: Book Heat and Mass Transfer Heat-5 CH7-1](https://reader035.fdocuments.us/reader035/viewer/2022062517/55cf9ac0550346d033a3391a/html5/thumbnails/7.jpg)
# 7
Heat Transfer Su Yongkang
School of Mechanical Engineering
Empirical method to obtain heat transfer coefficient
• How to set up an experimental test?
• Let’s say you want to know the heat transfer rate of an airplane wing (with fuel inside) flying at steady conditions………….
• What are the parameters involved?
– Velocity, –wing length,
– Prandtl number, –viscosity,
– Nusselt number,
• Which of these can we control easily?
• Looking for the relation:
Experience has shown the following relation works well:
UT ,
surface wingT
U L
Pr Nu
nmLCNu PrRe
![Page 8: Book Heat and Mass Transfer Heat-5 CH7-1](https://reader035.fdocuments.us/reader035/viewer/2022062517/55cf9ac0550346d033a3391a/html5/thumbnails/8.jpg)
# 8
Heat Transfer Su Yongkang
School of Mechanical Engineering
UT ,inputPower
insulation
L
Empirical method to obtain heat transfer coefficient
• Experimental test setup
• Measure current (hence heat transfer) with various fluids and test conditions for
• Fluid properties are typically evaluated at the mean film temperature
UT ,
2
TT
T sf
![Page 9: Book Heat and Mass Transfer Heat-5 CH7-1](https://reader035.fdocuments.us/reader035/viewer/2022062517/55cf9ac0550346d033a3391a/html5/thumbnails/9.jpg)
# 9
Heat Transfer Su Yongkang
School of Mechanical Engineering
Analytical Solution – Laminar Flow
• Assume:– Steady, incompressible, laminar flow– Constant fluid properties– For flat plate,
• Boundary layer equations
• Blasius developed a similarity solution to the hydrodynamic equations in 1908 based on the stream function, (x,y)
0
y
v
x
u
2
2
y
u
y
uv
x
uu
2
2
y
T
y
Tv
x
Tu
Continuity
Momentum
Energy
UT ,
sT
y
![Page 10: Book Heat and Mass Transfer Heat-5 CH7-1](https://reader035.fdocuments.us/reader035/viewer/2022062517/55cf9ac0550346d033a3391a/html5/thumbnails/10.jpg)
# 10
Heat Transfer Su Yongkang
School of Mechanical Engineering
Analytical Solution – Laminar Flow (Cont’d)
• Define new dependent and independent variables,
• The momentum equation can be rewritten as
• And the boundary conditions are
yu
xv
and
uxu
f/
)(
xuy /
022
2
3
3
d
fdf
d
fd
0)0(0
fd
df
1
d
dfand
![Page 11: Book Heat and Mass Transfer Heat-5 CH7-1](https://reader035.fdocuments.us/reader035/viewer/2022062517/55cf9ac0550346d033a3391a/html5/thumbnails/11.jpg)
# 11
Heat Transfer Su Yongkang
School of Mechanical Engineering
Analytical Solution – Laminar Flow (Cont’d)
• Blasius solution summary:
• Conclusions from the Blasius solution:
• Solution for the thermal boundary layer:
– For Pr 0.6
– Expressing the local convection coefficient as:
– Then the Local Nusselt number is:
x
xu
x
u Re
x5
Re since but,
5x
u
1 and and x
0 2
Pr *
2
*2
T
fT
31
0η
*
Pr 0.332
T
0η
*
T
x
ukhx
For 0.6 Pr 50
Eq. 7.21
3/12/1 PrRe332.0 xx
x k
xhNu
![Page 12: Book Heat and Mass Transfer Heat-5 CH7-1](https://reader035.fdocuments.us/reader035/viewer/2022062517/55cf9ac0550346d033a3391a/html5/thumbnails/12.jpg)
# 12
Heat Transfer Su Yongkang
School of Mechanical Engineering
Analytical Solution – Laminar Flow (Cont’d)
• The Average Nusselt number over the whole plate found by integrating:
• Ratio of velocity to thermal boundary layer thickness:
x
1
0
x
xx
x dxhk
x
k
xhuN
y
x
th
For large Pr (oils):
Pr > 1000
y
x
thFor small Pr (liquid metals):
Pr < 0.1Fluid viscosity greater than thermal diffusivity
Fluid viscosity less than thermal diffusivity
Eq. 7.25
3/12/1 PrRe664.0 xxNu
![Page 13: Book Heat and Mass Transfer Heat-5 CH7-1](https://reader035.fdocuments.us/reader035/viewer/2022062517/55cf9ac0550346d033a3391a/html5/thumbnails/13.jpg)
# 13
Heat Transfer Su Yongkang
School of Mechanical Engineering
Analytical Solution – Laminar Flow (Cont’d)
• Solution for friction factor
• Textbook contains Nusselt number correlations for low Pr (liquid metals) and large Pr (oils)
2/1, Re328.1 xxfC
2/12
,, Re664.0
2/
xxs
xf uC
2/2,
,
u
C xsxf
x
uuxs
332.0,
x
xsxs dxx 0 ,,
1
![Page 14: Book Heat and Mass Transfer Heat-5 CH7-1](https://reader035.fdocuments.us/reader035/viewer/2022062517/55cf9ac0550346d033a3391a/html5/thumbnails/14.jpg)
# 14
Heat Transfer Su Yongkang
School of Mechanical Engineering
Analytical Solution – Turbulent Flow
• For flat plate in turbulent flow (more common)
60 Pr 0.6 Pr Re 0.0296PrStRe
Re 0.37 3154
xx
5-1x
xNu
x
Important point:
– Typically a turbulent boundary layer is preceded by a laminar boundary layer first upstream
need to consider case with mixed boundary layer conditions!
L
xcturb
xc
lamx dxhdxhL
h 1
0
75/1, 10ReRe0592.0
xxxfC
![Page 15: Book Heat and Mass Transfer Heat-5 CH7-1](https://reader035.fdocuments.us/reader035/viewer/2022062517/55cf9ac0550346d033a3391a/html5/thumbnails/15.jpg)
# 15
Heat Transfer Su Yongkang
School of Mechanical Engineering
Analytical Solution – Mixed Boundary Layer
• Integrating
5cx,
85
L1/5L
Lf,
5cx,
85
1/35/4
105Re 10 Re105
Re
1742 -
Re
0.074C
105Re 10 Re105
60 Pr 0.6
871)Pr-Re037.0(
L
L
LLNu
Equations 7.33 and 7.34
![Page 16: Book Heat and Mass Transfer Heat-5 CH7-1](https://reader035.fdocuments.us/reader035/viewer/2022062517/55cf9ac0550346d033a3391a/html5/thumbnails/16.jpg)
# 16
Heat Transfer Su Yongkang
School of Mechanical Engineering
Analytical Solution – Special Cases
• The existence of unheated starting length.
• When the boundary condition is a uniform surface heat flux.For laminar flow,
For turbulent flow,
60Pr 0.6 Pr Re 0.0308 3154x xNu
0.6Pr Pr Re 0.453 3121x xNu
x
ss h
qTxT
)(
![Page 17: Book Heat and Mass Transfer Heat-5 CH7-1](https://reader035.fdocuments.us/reader035/viewer/2022062517/55cf9ac0550346d033a3391a/html5/thumbnails/17.jpg)
# 17
Heat Transfer Su Yongkang
School of Mechanical Engineering
Methodology for a Convection Calculation
• Become immediately cognizant of the flow geometry.
• Specify the appropriate reference temperature and evaluate the fluid properties.
• Calculate the Reynolds number
• Decide whether a local or surface average coefficient is required.
• Select the appropriate correlation.
![Page 18: Book Heat and Mass Transfer Heat-5 CH7-1](https://reader035.fdocuments.us/reader035/viewer/2022062517/55cf9ac0550346d033a3391a/html5/thumbnails/18.jpg)
# 18
Heat Transfer Su Yongkang
School of Mechanical Engineering
Example – Cooling of automobile crankcase
• Given:– Automobile crankcase with approximate
dimensions of 0.6 m long, 0.2 m wide and 0.1 m deep.
– Surface temperature of 350 K– Ambient temperature of 300 K– Vehicle velocity of 30 m/s
• Find:– Heat loss from bottom surface exposed to
air stream
• What other information or assumptions needed?
![Page 19: Book Heat and Mass Transfer Heat-5 CH7-1](https://reader035.fdocuments.us/reader035/viewer/2022062517/55cf9ac0550346d033a3391a/html5/thumbnails/19.jpg)
# 19
Heat Transfer Su Yongkang
School of Mechanical Engineering
Example – Cooling of automobile crankcase (Cont’d)
1. Determine air properties at an average film temperature
2. Calculate Reynolds #
3. Calculate average Nusselt number (mixed b.l.)
4. Average convection coefficient is
5. BOTTOM SURFACE HEAT LOSS:
K 325 2
TTT s
f
Km
W Pr
m
sN
m
kg
23
k
![Page 20: Book Heat and Mass Transfer Heat-5 CH7-1](https://reader035.fdocuments.us/reader035/viewer/2022062517/55cf9ac0550346d033a3391a/html5/thumbnails/20.jpg)
# 20
Heat Transfer Su Yongkang
School of Mechanical Engineering
Example – Cooling of automobile crankcase (Cont’d)
• How to determine the heat loss from the other surfaces?– Assumptions …………..
– Analysis procedure ………
![Page 21: Book Heat and Mass Transfer Heat-5 CH7-1](https://reader035.fdocuments.us/reader035/viewer/2022062517/55cf9ac0550346d033a3391a/html5/thumbnails/21.jpg)
# 21
Heat Transfer Su Yongkang
School of Mechanical Engineering
Example: Cooling air over electronic chips
• Given:Cooling air drawn over electronic devices mounted on board.
• Devices are 4 x 4 mm in size, spacing = 0.25 mm• Find the surface temperature of the fourth device,
assumed uniform surface T.
• Assumptions?
• Solution Method?
T = 27 º C
V = 10 m/sQ = 40 mW each device
“turbulator”
15 mm C L
![Page 22: Book Heat and Mass Transfer Heat-5 CH7-1](https://reader035.fdocuments.us/reader035/viewer/2022062517/55cf9ac0550346d033a3391a/html5/thumbnails/22.jpg)
# 22
Heat Transfer Su Yongkang
School of Mechanical Engineering
Example: Consider atmospheric air at 25 and a ℃velocity of 25 m/s flowing over both surfaces of a 1-m long flat plate that is maintained at 125 . Determine ℃the rate of heat transfer per unit width from the plate for values of the critical Reynolds number corresponding to , , and .510 5105 610
![Page 23: Book Heat and Mass Transfer Heat-5 CH7-1](https://reader035.fdocuments.us/reader035/viewer/2022062517/55cf9ac0550346d033a3391a/html5/thumbnails/23.jpg)
# 23
Heat Transfer Su Yongkang
School of Mechanical Engineering
![Page 24: Book Heat and Mass Transfer Heat-5 CH7-1](https://reader035.fdocuments.us/reader035/viewer/2022062517/55cf9ac0550346d033a3391a/html5/thumbnails/24.jpg)
# 24
Heat Transfer Su Yongkang
School of Mechanical Engineering
External Flow: Flat Plate
KEY POINTS THIS SECTION• What key characteristic of external flow
compared to internal flow?• Heat transfer rate generally decreases with
increasing distance from leading edge.• Turbulent convective heat transfer generally
higher than laminar due to mixing effect within boundary layer.
• Experimental tests indicate that heat transfer coefficient will generally vary like:
• Concept of transition Re number.• Difference in boundary layer growth for high
and low Pr number fluids. • General correlation for Nusselt number for flow
over flat plate in laminar, turbulent and mixed flows.
nmL
fL C
k
LhNu Pr Re
![Page 25: Book Heat and Mass Transfer Heat-5 CH7-1](https://reader035.fdocuments.us/reader035/viewer/2022062517/55cf9ac0550346d033a3391a/html5/thumbnails/25.jpg)
# 25
Heat Transfer Su Yongkang
School of Mechanical Engineering
Have a good time!
Go back and review lecture notes!