BN-DS-C01 Overview of the piping design standardsThis page gives an overview of the piping design standards of the Red-Bag site. Also the approximate date of issue is given. The standards are therefore for reference only.

BN-DS-C01 Overview of the piping design standards http://www.red-bag.com/jcms/design-standards/201-bn-ds-c01-overview-of...

1 of 4 8/15/2013 4:34 PM

INDEX

DESCRIPTIONNo. No. OF

PAGESISSUE DATE

Index of Company Piping Standards BN-DS-C1 5 2 Feb. ‘91

Dimensions and Particulars of Line Pipe BN-DS-C2 6 2 Jan. ‘91

Dimensions of Valves BN-DS-C3 1 2 Jan. ‘91

Dimensions of Line Pipe, Reducers, Elbows, Capsand required spacing between lines

BN-DS-C4 1 2 Jan. ‘91

Dimensions 30° and 60° Bends BN-DS-C5 1 2 Jan. ‘91

ANSI Standard Welding Tees BN-DS-C6 1 2 Jan. ‘91

150 lb ANSI Fabricated Flanged Fittings BN-DS-C7 1 2 Jan. ‘91

300 lb ANSI Fabricated Flanged Fittings BN-DS-C8 1 2 Jan. ‘91

Welding Neck Flanges - ANSI 150, 300, 400, 600,900, 1500 and 2500 lb

BN-DS-C9 7 3 Jan. ‘91

Slip-on, Threaded and Socket Type Flanges - ANSI150, 300, 400 and 600 lb

BN-DS-C10 6 2 Jan. ‘91

Lap-joint Stub Ends and Caps BN-DS-C11 1 3 Jan. ‘91

Weldolets BN-DS-C12 1 2 Jan. ‘91

Replaced by BN-DS-C50 BN-DS-C13 3 1

Machine and Stud Bolt Dimensions for Flanges -150, 300, 400, 600, 900, 1500 and 2500 lb(Dimensions in inches)

BN-DS-C14 7 2 Jan. ‘91

Machine and Stud Bolt Dimensions for Flanges -150, 300, 400, 600, 900, 1500 and 2500 lb(Dimensions in MM)

BN-DS-C15 7 2 Feb. ‘91

Dimensions and Bolting ANSI 300 lb Steel OrificeFlanges

BN-DS-C16 1 2 Jan. ‘91

Replaced by BN-DS-C55 BN-DS-C17 1 1

90° Mitre Bends - R=D and 1 1/2 D nom (3Sections)

BN-DS-C18 2 2 Jan. ‘91

Replaced by BN-DS-C58/59 BN-DS-C19 2 1

Replaced by BN-DS-C55/56 BN-DS-C20 2 1

Replaced by BN-DS-C61 BN-DS-C21 1 1

Y-type Suction Strainers BN-DS-C22 1 2 Jan. ‘91

Replaced by BN-DS-C66 BN-DS-C23 2 1

Replaced by BN-DS-C44 BN-DS-C24 1 1

Recommended Maximum Horizontal Spans inMaters

BN-DS-C25 2 3 Jan. ‘91

Maximum Pipe Spans based upon Deflection andStress

BN-DS-C26 3 2 Jan. ‘91

Replaced by BN-DS-C45 BN-DS-C27 3 1

Replaced by BN-DS-C43 BN-DS-C28 4 1

Swaged Nipples BN-DS-C29 1 3 Jan. ‘91

Replaced by BN-DS-C63 BN-DS-C30 1 1

Replaced by BN-DS-C46 BN-DS-C31 1 1

“L” Bend Nomogram BN-DS-C32 4 1 24-04-89

Thermal Expansion Data BN-DS-C33 4 2 Jan. ‘91

Replaced by BN-DG-C3 BN-DS-C34 29 1

Replaced by BN-DS-C53 BN-DS-C35 1 1

Replaced by BN-DS-C54 BN-DS-C36 1 1

BN-DS-C01 Overview of the piping design standards http://www.red-bag.com/jcms/design-standards/201-bn-ds-c01-overview-of...

2 of 4 8/15/2013 4:34 PM

INDEX

DESCRIPTIONNo. No. OF

PAGESISSUE DATE

Replaced by BN-DG-C4 BN-DS-C37 7 1

Inches and Fractions of an Inch Expressed as aDecimal of a Foot

BN-DS-C38 1 2 Jan. ‘91

Wire and Sheet Metal Gauges BN-DS-C39 1 2 Jan. ‘91

Metric Conversion Table Inches and Fractions of anInch to Millimeters

BN-DS-C40 4 2 Jan. ‘91

Metric Conversion of Pressures, Weights, Volumesand Temperatures

BN-DS-C41 4 2 Jan. ‘91

Pipe Spacing Standard Metric Units BN-DS-C42 7 2 Jan. ‘91

Typical Pump Piping BN-DS-C43 4 2 Jan. ‘91

Condensate Pots for Steam Mains BN-DS-C44 1 1 21-04-89

Typical Service Station Hook-up at Grade and atPlatform

BN-DS-C45 2 1 21-04-89

Typical Steam Snuffing Manifold forNonfreezing/Freezing Climates

BN-DS-C46 2 1 21-04-89

Plot Arrangement and Typical Section thruPipe-way

BN-DS-C47 2 2 Feb. ‘91

Typical Exchanger Piping and Data HorizontalExchangers

BN-DS-C48 3 2 Feb. ‘91

Typical Air Fin Piping and Data BN-DS-C49 2 2 Feb. ‘91

Dimensions for Screwed and Socket Weld Fittings BN-DS-C50 2 2 Feb. ‘91

Projection for Welded on Fittings Full Sizes,Reducing Sizes and 45° Branch Connections

BN-DS-C51 6 1 19-04-89

Drawing Format BN-DS-C52 1 1 19-04-89

Flanged Control Valves Piping Manifold 150, 300and 600 lb Gate Valves CS

BN-DS-C53 1 2 Feb. ‘91

Flanged Control Valves Piping Manifold 150, 300 -600 lb Gate Valves MSS Stub Ends

BN-DS-C54 1 2 Feb. ‘91

Two Weld 90° Miter Elbow BN-DS-C55 1 2 Jan. ‘91

Two Weld 45° Miter Elbow BN-DS-C56 1 2 Jan. ‘91

One Weld 45° Miter Elbow BN-DS-C57 1 2 Jan. ‘91

Three Weld 90° LR Miter Elbow BN-DS-C58 1 2 Jan. ‘91

Three Weld 90° SR Miter Elbow BN-DS-C59 1 2 Jan. ‘91

Five Weld 90° Miter Elbow BN-DS-C60 1 2 Jan. ‘91

Standard Dimensions for Temporary Strainers(Conical Type)

BN-DS-C61 1 2 Jan. ‘91

Special Fabricated Large DiameterConcentric/Eccentric Reducers

BN-DS-C62 2 2 Jan. ‘91

Clearances required for Personnel BN-DS-C63 1 1 18-04-89

Ring Type Joint Dimensions for Valves and Flanges BN-DS-C64 1 1 18-04-89

Fuel Piping Vertical Cylindrical Heaters BN-DS-C65 1 2 Jan. ‘91

Spectacle Flanges Single Blind-Ring Spacers/RingJoint Male/Ring Joint Female/Dimensions andWeights

BN-DS-C66 3 2 Feb. ‘91

Jack Screws Size Selection and Installation Detailfor FF, RF and RJ

BN-DS-C67 2 1 18-04-89

Dimensions for WN flanges 26”-60” API Standard605 150-300-600 and 900 lb

BN-DS-C68 4 2 Feb. ‘91

BN-DS-C01 Overview of the piping design standards http://www.red-bag.com/jcms/design-standards/201-bn-ds-c01-overview-of...

3 of 4 8/15/2013 4:34 PM

INDEX

DESCRIPTIONNo. No. OF

PAGESISSUE DATE

Minimum Spacing for Refineries and PetrochemicalPlants

BN-DS-C69 2 2 Feb. ‘91

Valve Locking Arrangement BN-DS-C70 3 2 Feb. ‘91

BN-DS-C01 Overview of the piping design standards http://www.red-bag.com/jcms/design-standards/201-bn-ds-c01-overview-of...

4 of 4 8/15/2013 4:34 PM