Blizzard Outdoor Banner Stand · Blizzard Outdoor Banner Stand UB701 UI183U REV 2 06/08 We are...
2
Assembled Dimensions (mm): 2125 (h) x 800 (w) x 490 (d) approx (based upon 2000 x 800 graphic) Base footprint: 490 (w) x 350 (d) approx Weight: 3.5kg approx when empty and 18.5kg approx when filled with water. (requires 15 litres approx) Maximum Graphic Dimensions: 2000 (h) x 800 (w) approx Minimum Graphic Dimensions: 1500 (h) x 600 (w) Substrate: Lightweight outdoor banner material (solid or mesh type substrates) Graphic requires 4 off 13mm eyelets 11.5mm recommended minimum internal eyelet diameter Included in kit: Base, telescopic pole /support arms and bottom rail. Availability: Anodised silver/blue base Optional accessories: Carry bag hardware specifications graphic specifications additional info Blizzard Outdoor Banner Stand UB701 UI183U REV 2 06/08 We are continually improving and modifying our product range and reserve the right to vary the specifications without prior notice. All dimensions and weights quoted are approximate and we accept no responsibility for variance. E&OE. features & benefits • Ideal for point of sale, retail display or exhibition environments • Stylish design hollow plastic base for water or sand weighting agent • Fully adjustable graphic height and width • Graphic supported on simple eyelet system • Weather resistant Specifically designed for indoor and outdoor promotions or high traffic areas of display. Blizzard’s moulded base can be filled with either water or sand to provide stablilty in adverse weather conditions. 800mm (max) 600mm (min) 2000mm (max) 1500mm (min) Graphic dimensions and eyelet positioning Position eyelet centres 30mm in from each graphic corner
Transcript of Blizzard Outdoor Banner Stand · Blizzard Outdoor Banner Stand UB701 UI183U REV 2 06/08 We are...
Assembled Dimensions (mm):2125 (h) x 800 (w) x 490 (d) approx(based upon 2000 x 800 graphic)
Base footprint:490 (w) x 350 (d) approx
Weight:3.5kg approx when empty and 18.5kgapprox when �lled with water.(requires 15 litres approx)
Maximum Graphic Dimensions:2000 (h) x 800 (w) approx
Minimum Graphic Dimensions:1500 (h) x 600 (w)
Substrate:Lightweight outdoor banner material(solid or mesh type substrates)Graphic requires 4 o� 13mm eyelets11.5mm recommended minimuminternal eyelet diameter
Included in kit:Base, telescopic pole /support arms andbottom rail.
Availability:Anodised silver/blue base
Optional accessories:Carry bag
hardware speci�cations graphic speci�cations additional info
Blizzard Outdoor Banner StandU
B701
UI1
83U
REV
2 0
6/08
We are continually improving and modifying our product range and reserve the right to vary the speci�cations withoutprior notice. All dimensions and weights quoted are approximate and we accept no responsibility for variance. E&OE.
features & bene�ts
• Ideal for point of sale, retail display or exhibition environments
• Stylish design hollow plastic base for wateror sand weighting agent
• Fully adjustable graphic height and width
• Graphic supported on simple eyelet system
• Weather resistant
Speci�cally designed for indoor and outdoorpromotions or high tra�c areas of display. Blizzard’smoulded base can be �lled with either water or sand toprovide stablilty in adverse weather conditions.
800mm (max)600mm (min)
2000
mm
(max
)15
00m
m (m
in)
Graphic dimensions and eyelet positioning
Position eyelet centres 30mmin from each graphic corner
Assembly Instructions
Remove cap and fill the base withwater or sand.
1
Insert the telescopic pole set intothe base.
2
Kit includes: Base, telescopic pole/support arms and bottom rail.
Twist the telescopic pole hub tothe right to unlock, then raise thepole to the desired height.
Twist the telescopic pole hub tothe left to lock.
5
Open out the banner supportarms.
3
64
Attach the top graphic eyelets tothe support arm hooks.
Unlock the telescopic bottom railby lifting up the lever.
7
Push down on the lever tolock the rail into place
9 10
Extend the bottom rail to suit thegraphic width.
8
12
Attach the bottom graphiceyelets to the rail hooks.
11
Slide the rail stay cord to thecentre of the base.
If necessary adjust the telescopicpole to add tension to thegraphic.
