SCHEDULEintra.itiltd-india.com/bgp/tenders/new bill of quantities... · Web viewAmount c 1Core 150...

SCHEDULE

SUB : Electrical Work for establishing the Data Center at F86 Hangar

PROJECT ITI DC AT BANGALORE

SUB ELECTRICAL BOQ_ LT Work DATE/REV 08-06-2017- R3

SR No Description Unit Qty Supply Rate

Installation Rate

Supply Amount

Installation Amount

COST SUMMARY1 INSTALLATION OF LT PANELS DISTRIBUTION BOARDS - -2 CABLES , BUS DUCT & SUB MAINS - -3 LIGHITNG FIXTURES & FITTINGS SUPPLY ONLY - -4 POINT WIRING, POWER OULETS & CIRCUITS - -5 CABLE TRAYS & RACEWAY - -6 EARTHING & MISCELENEOUS WORK - -7 LIGHTNING ARRESTOR - -8 HT WORK ( Local VCB & cabling) - -

Note:

Making of Shop drawings, Asbuilt layouts, operation manual , labeling of power outlets, light fixtures with self adhesive tape, taging of cables with Al tag etc is part of this scope without any extra cost.

SUB TOTAL - - GST @ 28% 28% - GST @ 18% 18% - Grand Total with All Taxes -

Contd….2..

- 2 -

SR No

Description Unit Qty Supply Rate

InstallationRate

SupplyAmount

InstallationAmount

1 LT DISTRIBUTION BOARDS

Safely Handiling , Shifting as required on site , positioning of panels provided , Assisting for coupling of panels sections to panel builder. Testing & commisioning along with Panel builder of following panels , Refer SLD for further details .

FORM 3 B TYPE 1.1 MLTP-1A & 1B Set 2.00 - -

As per SLD - -1.2 MLTP-2A & 2B Set 2.00 - -

As per SLD - -1.3 CHILLER PANELS Set 2.00 - -

As per SLD - -1.4 Primary Pump Panel Set 1.00 - -

As per SLD - -1.5 Secondary Pump Panel Set 1.00 - -

As per SLD - -1.6 UPS I/P Panel 1A & 1B Set 2.00 - -

As per SLD - -1.7 UPS I/P Panel 2A & 2B Set 2.00 - -

As per SLD - -1.8 UPS O/P Panel 1A & 1B Set 2.00 - -



As per SLD - -

Contd….3.

- 3 - SR Description Unit Qty Supply Installation Supply Installation

No Rate Rate Amount Amount1.11 DC Panel 1A & 1B (21S) AT GROUND FLOOR Set 2.00 - -

As per SLD - -1.12 DC Panel 2A & 2B (21S) AT 1ST FLOOR Set 2.00 - -

As per SLD - -1.13 DC Panel 1A & 1B (F85) AT 1ST FLOOR Set 2.00 - -

As per SLD - -1.14 DC Panel 2A & 2B (F85) AT 1ST FLOOR Set - -

As per SLD 2.00 - -1.15 DC Panel 3A & 3B (F85) AT 1ST FLOOR Set - -

As per SLD - -1.16 DC Panel 4A & 4B (F85) AT 2ND FLOOR Set 2.00 - -

As per SLD - -1.17 DC Panel 5A & 5B (F85) AT 3RD FLOOR Set - -

As per SLD 2.00 - -

1.18 PDU with 150KVA/125KVA/100KVA/75kVA Isolation Transfomer Set 100.00 - -

As per SLD - -1.19 SUB PANEL 1A& 1B AT 21S BLOCK Set 2.00 - -

As per SLD - -1.20 SUB PANEL 2A& 2B AT F85 BLOCK Set 2.00 - -

As per SLD - -1.21 LIGHTING & RAW POWER PANEL Set 7.00 - -

As per SLD - -1.22 2X100KVA AUX UPS O/P PANEL AT F85 BLOCK Set 1.00 - -

As per SLD - -1.23 AUX UPS SUB PANEL AT 21S BLOCK Set 1.00 - -

As per SLD -

Contd.4..

-4- SR Description Unit Qty Supply Installation Supply Installation

No Rate Rate Amount Amount1.24 500KVA APFC PANEL with detuned reactors Set 4.00 - -

As per SLD or given detail in SLD - -1.25 420KVA APFC PANEL with detuned reactors Set 4.00 - -

As per SLD or given detail in SLD - -1.26 120KVAR THYRISTER SWITCHING APFC PANEL Set 4.00 - -

As per SLD or given detail in SLD - -

1.27 1250A FP ATS with end termination box for Chillers with indicating lamps , complete in all respect Set 4.00 - -

As per SLD or given detail in SLD - -1.28 PAC PANEL Set 14.00 - -

As per SLD - -

1.29 40A FP ATS with Indicating lamps & cabel end termination box , complete in all respect , Set 70.00 - -

as per SLD for PAHU - -1.30 FINAL DISTRIBUTION BOARDS - -

Supplying and fixing of following types of factory fabricated prewired SPN and TPN double door sheet steel MCB distribution boards, moisture, dust and vermin proof having IP 42 degree of

protection, 240/415 volts, on surface/recess, complete with tinned copper busbar, neutral busbar, earth bar, din bar,

interconnections, finished with powder coating including , earthing etc. as required :

- -

a LIGHTING DB (LDB) Set 14.00 - -TPN DB with the following: - -

Incommer - -1 No.40A, FP MCB and 3 nos.40A/30mA DP RCCBs each per

phase with separate neutral & earth links per phase - -

Outgoings - -18 Nos.6A/10/16A SP MCB's - -

Contd…5.

- 5 - SR Description Unit Qty Supply Installation Supply Installation

No Rate Rate Amount Amountb RAW POWER DB (RPDB) Set 15.00 - -

TPN DB with the following: - -Incommer - -

1 No.63A, FP MCB and 3 nos.63A/100mA DP RCCBs each per phase with separate neutral & earth links per

phase- -

Outgoings - -24 Nos.10/16/20/25 A SP MCB's - -

c UPS DB Set 5.00 - -TPN DB with the following: - -

Incommer - -1 No 40A, FP MCB and 3 nos.32A DP MCB each per phase with separate neutral & earth links per phase - -


d UPS DB Set 5.00 - -TPN DB with the following: - -

Incommer - -1 No.63A, FP MCB and 3 nos.63A DP MCBs each per phase with separate neutral & earth links per phase - -


e SPN DB (ELDB) Set 14.00 - -SPN DB with the following: - -

Incommer 25A,30mA DP RCCB - 1 No. - -Outgoing 6/10A SP MCBs -6 Nos. - -

f DB with following configuration Set 7.00 - -Incommer - -

1 No.100A, TP MCCB - -

Contd…6.

- 6 - SR No Description Unit Qty Supply

RateInstallation

RateSupplyAmount

InstallationAmount

Outgoings - -2 Nos 25A TP MCB's - -

12 Nos.25/32A SP MCB's - -Note: - -

All MCCB Should have min Breaking capacity of 25KA unless specified - -

All MCCB will have rotary handle - -All MCCB should have Ics=Icu - -

All MCB will be rated for 10KA breaking capacity & C'curve characteristics - -

TOTAL FOR PANELS & D.B'S - -2 CABLES , BUS DUCT & SUB MAINS

2.1

Supply, Testing & Laying of aluminum / copper armoured/ unarmoured PVC/XLPE Insulated 1.1V

agreed cables fixed to walls, ceilings, on trays or laid in ready-made trench as per standard practices .

a 3.5 Core 400 sq. mm. XLPE AL cable - A2XFY mtr 10,500.00 - -b 3.5 Core 300 sq. mm. XLPE AL cable - A2XFY mtr 200.00 - -c 3.5 Core 300 sq. mm. XLPE Copper cable - 2XFY mtr 355.00 - -d 3.5 Core 240 sq. mm. XLPE AL cable - A2XFY mtr 100.00 - -e 4 Core 240 sq. mm. XLPE AL cable - A2XFY mtr 3,500.00 - -f 4 Core 240 sq. mm. XLPE Copper cable - 2XFY mtr 442.00 - -g 4 Core 185 sq. mm. XLPE AL cable A2XFY mtr 100.00 - -h 3.5 Core 185 sq. mm. XLPE AL cable- A2XFY mtr 1,500.00 - -i 4 Core 150 sq. mm. XLPE AL cable - A2XFY mtr 1,700.00 - -j 4 Core 120 sq. mm. XLPE AL cable A2XFY mtr 200.00 - -k 3.5 Core 120 sq. mm. XLPE AL cable A2XFY mtr 100.00 - -l 4 Core 70 sq. mm. XLPE AL cable A2XFY mtr 100.00 - -

m 3.5 Core 50 sq. mm. XLPE AL cable A2XFY mtr 400.00 - -n 3.5 Core 35 sq. mm. XLPE AL cable A2XFY mtr 1,000.00 - -o 3.5 Core 25 sq. mm. A2XFY mtr 100.00 - -

Contd…7..

- 7 -

SR No Description Unit Qty Supply

RateInstallation

RateSupplyAmount

InstallationAmount

p 4 Core 16 sq. mm. A2XFY mtr 900.00 - -

q 4 Core 10 sq. mm. A2XFY mtr 900.00 - -

r 3.5Core 25 sq. mm. 2XFY mtr 120.00 - -

s 4 Core 16 sq. mm. . 2XFY mtr 150.00 - -

t 4 Core 10 sq. mm. . 2XFY mtr 300.00 - -

u 12Core 1.5 sq. mm . 2XFY mtr 200.00 - -

v 4Core 6 sq. mm . 2XFY mtr 7,000.00 - -

x 4Core 4 sq. mm . 2XFY mtr 300.00 - -

y 2 Core 6 Sq mm . 2XFY mtr 200.00 - -

z 3 Core 4 Sq mm . 2XFY mtr 800.00 - -

aa 3 Core 2.5 sq. mm . 2XFY mtr 100.00 - -

2.2

Cable end termination of above armoured cables with Heavy duty Lugs & Brass cable glands. Including cost of

all crimping lugs and DOUBLE compression glands, cable sockets insulation tape, sealing compound etc:

Tagging , Glands boot will be part of this scope.

- -

a 3.5 Core 400 sq. mm. XLPE AL cable - A2XFY Nos. 60.00 - -

b 3.5 Core 300 sq. mm. XLPE AL cable - A2XFY Nos. 30.00 - -

c 3.5 Core 300 sq. mm. XLPE Copper cable - 2XFY Nos. 12.00 - -

d 3.5 Core 240 sq. mm. XLPE AL cable - A2XFY Nos. 4.00 - -

e 4 Core 240 sq. mm. XLPE AL cable - A2XFY Nos. 20.00 - -

f 4 Core 240 sq. mm. XLPE Copper cable - 2XFY Nos. 10.00 - -

g 4 Core 185 sq. mm. XLPE AL cable A2XFY Nos. 20.00 - -

h 3.5 Core 185 sq. mm. XLPE AL cable- A2XFY Nos. 20.00 - -

i 4 Core 150 sq. mm. XLPE AL cable - A2XFY Nos. 4.00 - -

Contd…8..

- 8 -


RateInstallation

RateSupplyAmount

InstallationAmount

j 4 Core 120 sq. mm. XLPE AL cable A2XFY Nos. 4.00 - -

k 3.5 Core 120 sq. mm. XLPE AL cable A2XFY Nos. 10.00 - -l 4 Core 70 sq. mm. XLPE AL cable A2XFY Nos. 4.00 - -

m 3.5 Core 50 sq. mm. XLPE AL cable A2XFY Nos. 20.00 - -n 3.5 Core 35 sq. mm. XLPE AL cable A2XFY Nos. 20.00 - -o 3.5 Core 25 sq. mm. A2XFY Nos. 20.00 - -p 4 Core 16 sq. mm. A2XFY Nos. 10.00 - -q 4 Core 10 sq. mm. A2XFY Nos. 10.00 - -r 3.5Core 25 sq. mm. 2XFY Nos. 10.00 - -s 4 Core 16 sq. mm. . 2XFY Nos. 200.00 - -t 4 Core 10 sq. mm. . 2XFY Nos. 10.00 - -u 12Core 1.5 sq. mm . 2XFY Nos. 10.00 - -v 4Core 6 sq. mm . 2XFY Nos. 60.00 - -x 4Core 4 sq. mm . 2XFY Nos. 20.00 - -y 2 Core 6 Sq mm . 2XFY Nos. 20.00 - -z 3 Core 4 Sq mm . 2XFY Nos. 15.00 - -

aa 3 Core 2.5 sq. mm . 2XFY Nos. 20.00 - -

2.3 Supply & laying of Copper Flex cables/wires with flexible conduits as follows - -

a 1Core 400 sqmm cu flexible cable Mtr 2,100.00 - -b 1Core 240 sqmm cu flexible cable Mtr 200.00 - -c 1Core 150 sqmm cu flexible cable Mtr 1,500.00 - -d 1Core 120 sqmm cu flexible cable Mtr 1,440.00 - -e 1 Core 35 Sqmm PVC insulated flexible cable Mtr 200.00 - -f 1 Core 25 Sqmm PVC insulated flexible cable Mtr 200.00 - -g 1 Core 16 Sqmm PVC insulated flexible cable Mtr 200.00 - -

2.4Cable end termination of above unarmoured flexi

cables with Heavy duty Cu. Lugs . Including cost of all crimping lugs, insulation tape,etc:

- -

a 1Core 400 sqmm cu flexible cable Nos 200.00 - -b 1Core 240 sqmm cu flexible cable Nos 120.00 - -

Contd….9..

- 9 -


RateInstallation

RateSupplyAmount

InstallationAmount

c 1Core 150 sqmm cu flexible cable Nos 40.00 - -

d 1Core 120 sqmm cu flexible cable Nos 40.00 - -e 1 Core 35 Sqmm PVC insulated flexible cable Nos 20.00 - -f 1 Core 25 Sqmm PVC insulated flexible cable Nos 20.00 - -g 1 Core 16 Sqmm PVC insulated flexible cable Nos 16.00 - -

2.5 Supply, Installation, Testing & commisioning of Sandwich Copper busduct with 2x80x6mm external copper earthing. Vendor to study site & prepare design for the same, Below

quantities are indicative & it will be on actula basis.

- -

a 6300A Straight Length - IP 54 with canopy Mtrs. 12.00 - -b 5000A Straight Length - IP 54 with canopy Mtrs. 220.00 - -c 6300A Vertical Bends - IP 54 Nos 20.00 - -d 6300A Horizontal Bends - IP 54 Nos 20.00 - -e 5000A Vertical Bends - IP 54 Nos 10.00 - -f 5000A Horizontal Bends - IP 54 Nos 10.00 - -g 6300A Flange end - Provision + Adopter box Nos 8.00 - -h 5000A Flange end - Provision + Adopter box Nos 8.00 - -i 6300A Copper flexible (R,Y,B,N - 1 st) Nos 8.00 - -j 5000A Copper flexible (R,Y,B,N - 1 st) Nos 8.00 - -

MAKES : C&S/LEGRAND/ALFADUCT/SCHNIEDER - -TOTAL FOR CABLES & SUB MAINS - -

3 LIGHITNG FIXTURES & FITTINGS SUPPLY ONLYSupply of following of prewired light fittings/ light

tracks, complete The fitting shall be fixed with chain ,screws etc. & recessed mounted in false ceiling. Cost of chains Screws to be considered in these items

3.1 40W LED SQUARE LIGHT

Contd…10..

- 10 -SR No Description Unit Qty Supply

RateInstallation

RateSupplyAmount

InstallationAmount

Ultra modern recess mounting luminaire with high performance LEDs, suitable for Nos 300.00 - -

mounting with Armstrong/ Grid ceiling complete with Drivers & all required accessories.High transmittance polystyrene opal diffuser for glare free symmetric light distribution. 40W LED 2x2 Panel, PF≥0.95 & THDi ≤10%, CCT 5700K, System Lumens 100lm/W.Type -Havells Venus Neo 42W LED LHEWDRP7PK1W042

Make : Wipro/Philips/Havels - -3.2 LED DOWN LIGHTER 18 WATTS - -

Recess mounted pressure die-cast aluminium luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and independent electronic LED driver. Elegantly designed pressure die-cast aluminium housing & ring for efficient heat dissipation is white powder coated after phosphochromate treatment. 18W LED Downlight, PF≥0.95 & THDi ≤10%, CCT 5700K, System Lumens 100lm/W.Type - Havells Endura DL Neo 18W LED LHEBJNP7PV1W018

Nos 400.00 - -

Make : Wipro/Philips/Havels - -3.3 LED DOWN LIGHTER 7 WATTS - -

Recess mounted pressure die-cast aluminium luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and independent electronic LED driver. Elegantly designed pressure die-cast aluminium housing & ring for efficient heat dissipation is white powder coated after phosphochromate treatment. 07W LED Downlight, PF≥0.95 & THDi ≤10%, CCT 5700K, System Lumens 80lm/W.Type : Havells Endura DL Neo 07W LED LHEBJNP7PZ1W007

Nos 60.00 - -

Make : Wipro/Philips/Havels - -3.4 40W LED SURFACE MOUNTED LIGHT - -

Surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver, Made of ultra slim co-extruded polycarbonate channel with housing part in white finish & diffuser part in reeded opal finish. White finish ABS end caps with decorative circular coloured polycarbonate cap snap fitted on the end cap to enhance the aesthetic of the fixture. These end caps are snap-fitted to the fixture. 18W LED Batten, PF≥0.95 & THDi ≤20%, CCT 5700K, System Lumens 100lm/W.Type :Havells Lumiline 18W LED BATTEN LHEXBQP7PN1W018

Nos 650.00 - -

Make : Wipro/Philips/Havels - - Contd…11..

- 11 -


RateInstallation

RateSupplyAmount

InstallationAmount

3.5 20W LED Tube light (4 ft) - -

Surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver, Made of ultra slim co-extruded polycarbonate channel with

housing part in white finish & diffuser part in reeded opal finish. White finish ABS end caps with decorative circular coloured polycarbonate cap snap fitted on the

end cap to enhance the aesthetic of the fixture. These end caps are snap-fitted to the fixture. 18W LED Batten, PF≥0.95 & THDi ≤20%, CCT 5700K, System Lumens

100lm/W.Type :Havells Lumiline 18W LED BATTEN LHEXBQP7PN1W018

Nos 50.00 - -

Make : Wipro/Philips/Havels - -3.6 EXIT SIGNAGES Nos. 40.00 - -

Decorative 'exit' ELD light,fitted into false ceiling with brush-steel finish flush plate & 12mm thick plate glass or acrylic with 'exit' and arrow logo in green with

in built battery back up of 30min- -

(PROLITE MAKE) - -3.7 LIGHTING CONTROL PANEL SET 5.00 - -

Light dimming system in conference/meeting rooms comprising of 6 channels with 6 scene setting system with all necessary hardware and wall plate having

architectural finish and all other necessary acessories but excluding the dimmable ballasts to make the system complete in all respect. (ce/ul approved) (cost to

include decorative scene setting wall switch plate + dimmiing interface near ldb + converters etc as required)

- -

Contd…12..

-12 -


RateInstallation

RateSupplyAmount

InstallationAmount

Lutron - -

3.8 EXHAUST FANS - -Heavy duty Exhaust fans of window mounted type with bird screen and

louvered shutters – 9 inch dia of approved make and colour or Approved equivalent.

Nos 20.00 - -

3.9 PIR SENSORS - -dual technology Occupancy Sensor/presence detector.Detection range

Horizontal(360 degree) & Vertical(120 degree).switch off delay@ 10 sec-21 min & stand by time@0 sec-60 min.Input voltage 230+ 10%,50

Hz.Switching capacity 1200 watt . Sensor shall be suitable for the above fittings considered.

Nos 120.00 - -

Make : Schnieder/Philips / Legrand/Lutron - -3.10 LED STRIP - -

12W/ mtr LED strip with Al profile with drivers , complete in all respect. Flexible PCB, Dual layers, 5000x10x2mmCable: Dual wires: red and black

color single sided tape is used at the back of the strip to mount it.Type :Havells LED Flexistrip 11W/M LHEHDEP5UN1F055

Mtr 60.00 - -

Notes: - -a All fixtures shall be complete with lamps and control gear. - -b Necessary down rods, hanging chains etc shall be part of the fixtures. - -

c Samples of all the fixtures shall be submitted to the architect before supply & approval is taken. - -

d Please check the quantity from drawings / architect / consultant before ordering. - -

Contd…13..

- 13 -


RateInstallation

RateSupplyAmount

InstallationAmount

e Color rendering index of the lamps to be confirmed from - -

architect / consultant before ordering.TOTAL FOR LIGHITNG FIXTURES & FITTINGS SUPPLY ONLY 1,705.00 - -

4 POINT WIRING, POWER OULETS & CIRCUITS

4.1

Wiring for following points with 1.5 sq.mm FRLS PVC insulated flexible copper conductor single core wires of 1100 V grade in recess or surface FR PVC ISI marked conduit with plate type modular switches complete with accessories such as bends, junction boxes, pull wire including 1.5

sq.mm copper conductor green color earth wire for earthing of all metal boxes, light fixtures, exhaust fan etc. complete as required including

circuit wiring with 2x2.5+1x1.5 sq. mm FRLS wires.

- -

a Primary (First) point - MCB DB control Nos 120.00 - -b Primary (first) point.- 5A switch control Nos 250.00 - -c Secondary (looping) point Nos 1,000.00 - -

4.2 Same as above for Emergency lighting - -a Primary (First) point - MCB DB control Nos 32.00 - -b Primary (first) point.- 5A switch control Nos 60.00 - -c Secondary (looping) point Nos 220.00 - -

4.3 Wiring for 5 A light plug outlets with 5A switch Socket. Onboard Set 5.00 - -

4.4

Providing fixing of following type of 240V, 1phase power outlets with required accessories & wiring complete with modular Switch / Socket

with suitable size of GI box complete in all respect, wiring to be laid thru existing raceways/conduits

- -

a1x6 A round pin Raw/UPS switched socket outlet with 2x2.5 sq.mm FRLS PVC insulated copper wire & earthing with 2.5 sq.mm insulated copper

wire , ( 4/5 points can be looped in one circuit)Set 30.00 - -

Contd….14.

- 14 -


RateInstallation

RateSupplyAmount

InstallationAmount

c 2x13 A Multistandard UPS Socket & 1x6A switch outlet with 2x2.5 Set 120.00 - -

sq.mm FRLS PVC insulated copper wire & earthing with 2.5 sq.mm insulated copper wire , ( 4/5 points can be looped in one circuit)

Two Socket & One switch

d

3x13 A Multistandard UPS socket & 1x16 switched outlet with 2x2.5 sq.mm FRLS PVC insulated copper wire & earthing with 2.5 sq.mm insulated copper wire , ( 3/4 points can be looped in one

circuit) Three Socket & One switch

Set 100.00 - -

e

1x6/16 A Round RAW switched socket outlet with 2x4 sq.mm FRLS PVC insulated copper wire & earthing with 2.5 sq.mm insulated

copper wire , ( 2/3 points can be looped in one circuit) For Convenience outlets

Set 130.00 - -

f 32A, 2P+E, IEC309 Socket with Plug, PVC moulded / housed in metal board,interlocked , with DP MCB, For Server Racks Nos 650.00 - -

g 63A, 2P+E , IEC309 Socket with Plug, PVC moulded / housed in metal board,interlocked ,with DP MCB, For Server Racks, Nos 1,450.0

0 - -

h 32A, 3P+N+E , IEC309 Socket with Plug, PVC moulded / housed in metal board,interlocked,with DP MCB, For Server Racks Nos 155.00 - -

Make : Scame, Neptune , Legrand - -- -

4.5 Supply, installation, testing & commissioning of metal board with 80 Amp 4 P ISOLATOR IP- 44 for AC Nos QRO

4.6 Supply & Installation of Power outlets with face plates , back boxes etc as required at site

a 5A power outlets with Switch socket. Nos QROb 15A power outlets with Switch socket. Nos QRO

c 20A Rey roll Plug-Sockets with 3 Pin Metal Top Housed in metal board with 20A SP MCB. For indoor supply of Acs Nos 10.00 - -

Contd….15..

- 15 -


RateInstallation

RateSupplyAmount

InstallationAmount

4.7 Supply & Laying of circuit mains in alreasy provided cables - -

trays , termination with lugs & ferruling will be part of this scope for each circuits.

a 3 Core 2.5 sq.mm. Cu conductor PVC insulated FRLS Mtr 500.00 - -b 3 Core 4 sq.mm. Cu conductor PVC insulated FRLS Mtr 450.00 - -c 3 Core 6 sq.mm. Cu conductor PVC insulated FRLS Mtr 300.00 - -d 3 Core 10 sq.mm. Cu conductor PVC insulated FRLS Mtr 6,000.00 - -e 3 Core 16 sq.mm. Cu conductor PVC insulated FRLS Mtr 18,000.00 - -f 4 Core 16 sq.mm. Cu conductor PVC insulated FRLS Mtr 2,700.00 - -

TOTAL FOR POINT WIRING, POWER OULETS & CIRCUITS - -5 CABLE TRAYS & RACEWAY

5.1 Supply and laying of following sizes of floor raceways 2mm thick GI trunking with openable cover including clamping &

side knockout for fixting of power outlets .a 450mm x75mm Mtr 1,450.00 - -b 300mm x75mm Mtr 900.00 - -c 350mm x50mm Mtr 100.00 - -d 200mm x 50mm Mtr 50.00 - -e 150mm x 50mm Mtr 100.00 - -

5.2

Supply and installing of Galvanised floor junction boxes for the raceway mentioned above of following sizes with cover with four nos. SS screws with proper cutouts on the sides for conduit entry and screwed top cover with rubber gasket and

suitable knockouts for flexible conduit outlets as per the detailed drawing. All junction boxes to be properly earthed

with the raceways with copper earth wires as required complete in all respects.

- -

Contd….16…

- 16 -


RateInstallation

RateSupplyAmount

InstallationAmount

a 225mmx225mmx45mm Junction box suitable for above raceway to form Nos 100.00 - -

integral raceways.

b 165mmx165mmx45mm Junction box suitable for above raceway to form integral raceways. Nos 20.00 - -

5.3

Suppy and laying raceways/conduits on floor.The raceways/conduitsshall be fixed to the flooring with clamps for finished

levels as per site conditions or through parttions with all accessories, bends,pull wire etc. but excluding the mounted junction boxes,

bends,pull wire etc. but excluding the floor mounted junction boxes which shall be paid separately. The metal/PVC conduits/raceways shall be earh at suitable intervals the distance between data conduits and

power conduits shall be maintained atleast 6" apart., floor cutting to be included in this item

- -

a 100mm x 38mm Aluminium raceways, 1.6 mm thk. Mtr 500.00 - -b 63mm x 38mm Aluminium raceways, 1.6mm thk. Mtr 30.00 - -

c 25mm Dia FR HMS PVC Conduits Mtr 2,000.00 - -

d 50mm Dia FR HMS PVC Conduits Mtr 300.00 - -e 75mm x 50mm PVC Trunking of Precision make Mtr 200.00 - -f 75mm x 50mm MS powder coated Trunking with openable cover Mtr 300.00 - -

5.4

Supply and installing of 2 mm thicK GI floor junction boxes for the raceway mentioned above of following sizes with GI cover with four nos. SS screws with proper cutouts on the sides for conduit entry and screwed top cover and suitable knockouts for flexible conduit outlets as per the detailed drawing. All junction boxes to be properly earthed with the raceways with copper earth wires as required complete in all respects.

- -

Contd…17…

- 17 -


RateInstallation

RateSupplyAmount

InstallationAmount

a 250mmx250mmx45mm deep Nos 30.00 - -b 350mmx350mmx45mm deep Nos 20.00 - -c 450mmx450mmx45mm deep Nos 15.00 - -c 550mmx550mmx45mm deep Nos 2.00 - -

5.5

Supply & installations of heavy gauge perforated Cable Tray made of GI sheet steel., min 2 mm thick, with sides not less than 80 mm deep, fittings are to be same material as tray, each coupling should have GI earthing connector. . support shall be spaces not more than 1000mm apart & at all bends & couplings. the rate shall be inclusive of all other required

accessories, supports rods & plates etc.

- -

a 150mm wide x50mm depth Perforated type Cable tray Mtr 60.00 - -b 300mm wide x80mm depth Perforated type Cable tray Mtr 90.00 - -c 450mm wide x80mm depth Perforated type Cable tray Mtr 100.00 - -d 450mm wide x100mm depth Perforated type Cable tray Mtr 560.00 - -

5.6

SAME AS ABOVE but ladder type 50mm height, with rungs at 250mm spacing ,complete with couplers, bends etc. The rate

to include supports of 40x40mmx3mm base angle with vertical rod with couplers, required anchor fastener bolts.

The vertical supports shall be spaces at 1000mm apart & at all bends. All bends shall be smooth as per cable allowable bending radius. Trays to be fixed partly on ceiling & wall.

- -

a 150x50mm Ladder type Cable tray Mtr 600.00 - -b 300x50mm Ladder type Cable tray Mtr 500.00 - -c 450x50mm Ladder type Cable tray Mtr 500.00 - -d 600x50mm Ladder type Cable tray Mtr 800.00 - -

Contd…18..

- 18 -


RateInstallation

RateSupplyAmount

InstallationAmount

e 600x100mm Ladder type Cable tray Mtr 50.00 - -

f 1000x150mm Ladder type Cable tray Mtr 1,500.00 - -g 1200x100mm Ladder type Cable tray Mtr 60.00 - -

5.7

Supplying , Design , fabrication and erecting Iron work consisting of Various sections of MS and including Plates, Chequered Plates, Rods, Bars, MS pipes, etc. for panel board or any other purposes complete with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as

per directions by the authority

Kg 10,000.00 - -

5.8

Supply and laying of following sizes of 2mm thick MS Powder Coated trunking with openable cover including clamping & side knockout for

light point connection , The trunk will be supended to true ceiling with 8mm dia GI with threaded rods from both the sides & GI Bracket.The Cost should be inclusive of bend , couplers, supports etc . This is to be

used for installation of light fixtures in Server room

- -

a 100x50mm Mtr 400.00 - -b 150x50mm Mtr 50.00 - -c 75x50mm Mtr 100.00 - -

Note Shop drawings for cable supports to be approved first - -TOTAL FOR CONDUITING ,RACEWAY & CABLE TRAYS - -

6 EARTHING & MISCELENEOUS WORK

6.1

Supply Installation Testing &commissioning of Copper Pipe type earth pits with 80 mm dia, Three meters length pipe with specially developed on Pipe in

pipe/Strip concept filled with highly conductive & anticorrosive crystalline conductive mixture. The back fill is to be done by special compound which retains moisture & enhance conductivity. The rate should be inclusive of

making bore & finish & terminated in chamber, Test Links, masonry chamber with concrete base, manhole, 6 mm thick MS lockable cover with frame (300 x

300 mm) For dedicated Earth, make Ashlok/Fastelectro

Set 126.00 - -

Contd….19…

- 19 -

SR Description Unit Qty Supply Installation Supply Installation

No Rate Rate Amount Amount

6.2

Supply Installation Testing &commissioning of GI Pipe type earth pits with 80 mm dia, Three meters length pipe with

specially developed on Pipe in pipe/Strip concept filled with highly conductive & anticorrosive crystalline conductive mixture. The back fill is to be done by special compound which retains moisture & enhance conductivity. The rate

should be inclusive of making bore & finish & terminated in chamber, Test Links, masonry chamber with concrete base, manhole, 6 mm thick MS lockable cover with frame (300 x 300 mm) For dedicated Earth, make Ashlok/Fastelectro

Set 40.00 - -

6.3

Supply & laying of Earthing conductors/flat strips. The portion of the strip under-ground shall be laid to a depth of at least 60cms. The rates shall include cost of all materials &

accessories, excavation as required in soft soil/hard soil/concrates etc.

- -

a 75x10 mm Cu flat strips with heat shrinkable sleeves Mtr 700.00 - -b 50x6 mm Cu flat strips with heat shrinkable sleeves Mtr 80.00 - -c 40x6 mm Cu flat strips with heat shrinkable sleeves Mtr 600.00 - -d 32x6 mm Cu flat strips with heat shrinkable sleeves Mtr 60.00 - -e 25x3 mm Cu flat strips on insulator Mtr 50.00 - -f 50x6 mm AL flat strips Mtr 3,500.00 - -g 32x6 mm AL flat strips Mtr 1,000.00 - -h 25x6 mm GI flat strips Mtr 3,000.00 - -i 10 SWG Cu earth Mtr 1,200.00 - -j 25mm Braided Cu wire for server room earthing Mtr 3,500.00 - -

Contd…20…

- 20 -


RateInstallation

RateSupplyAmount

InstallationAmount

6.4 Supply & laying of single core flexible PVC insulated Copper - -

conductor . The portion of the strip /conductor under-ground shall be laid to a depth of at least 60cms. The rates shall

include cost of all materials & accessories, FRLS PVC HMS pipe inside building , GI Pipe at out side areas / under ground with each conductor, excavation as required in soft soil/hard

soil/concrates etc.a 1 core 185sqmm. Mtr 100.00 - -b 1 core 150 sqmm. Mtr 7,000.00 - -c 1 core 120 sqmm. Mtr 2,500.00 - -d 1 core 95 sqmm. Mtr 200.00 - -e 1 core 50 sqmm. Mtr 500.00 - -f 1 core 35 sqmm. Mtr 1,500.00 - -g 1 core 25 sqmm. Mtr 200.00 - -h 1 core 16 sqmm. Mtr 500.00 - -i 1 core 10sqmm. Mtr 200.00 - -j 1 core 6sqmm. Mtr 600.00 - -k 1 core 4sqmm. Mtr 600.00 - -

6.5

Supply & laying of following pipes . The pipes are to be laid underground at least 75cms. The rates shall include cost of all materials , Access Chambers as required & accessories , excavation as required in soft soil/hard soil/concrates etc.

- -

a 32MM DIA GI C Class pipe Mtr 500.00 - -b 50MM DIA GI C Class pipe Mtr 500.00 - -c 150MM DIA Hume pipe Mtr 120.00 - -d 300MM DIA Hume pipe Mtr 300.00 - -

Contd…21…

- 21 -


RateInstallation

RateSupplyAmount

InstallationAmount

6.6

Supply,installation,testing & commissioning of copper Earth bus of various size mounted on insulators ,in suitable size

painted MS box. Bus should have 10 nos of holes with brass nut bolts of suitable size

- -

a 50 mm x6mmx750 mm ( WxBxL) Nos 40.00 - -b 25 mm x6mmx600 mm ( WxBxL) Nos 20.00 - -

6.7Temporary arrangement for lighting & power for construction for Approx 75000 sft area (2buildings , G+3 & G+2), the scope covers as under.

LS 1.00 - -

Supply & Installation of Main Panel for temporary Lighting & power arrangemnet with MCCB / MCB / ELCB , Sub Panles at each floor , Sub DBs with 4xset of Industrial power outelts with top 4nos per floor , Lighting with LED tube lights , wiring with 3core / 4core flexible wires dully fixed on walls / ceiling . The contractor is sole responsible for any eletrocation happend at site hence ELCB at final outelts are compulsary.

- -

Contractor is responsible to maintain the entire installation in good working conditions till the job is completed / handed over to the owners. The necessary material required to complete the job and to maintain the same is solely responsibility of the contractor. The contractor has to cooperate with all other agencies and maintain the installation and provide necessary temporary power to all other bidders. All complete as required and as per the final direction and approval of the Architect / Consultant.

- -

6.8 SAFETY EQUIPMENTS - -

a

Supplying, erecting and connecting a 5 KG CO2 FIRE EXTINGUISHER properly fixed on the wall with necessary

clamps, screws, bolts and nuts etc. The extinguisher shall be suitable for all types of fires(A, B & C).

Nos 5.00 - -

Contd….22…

- 22 -


RateInstallation

RateSupplyAmount

InstallationAmount

b Supplying, erecting and connecting a 2 KG CO2 FIRE Nos 5.00 - -

EXTINGUISHER properly fixed on the wall with necessary clamps, screws, bolts and nuts etc. The extinguisher shall be

suitable for all types of fires (A, B & C).

cSupplying, erecting and connecting Treatment Chart in

English, Hindi, Local Language directly fixed onto the wall with necessary screws etc.

Nos 20.00 - -

d

Supplying and fixing PVC Synthetic elastomer electrically insulating mat with class C insulation conforming to IS: 15652 – 2006 & CPRI tested having 3mm thickness , 1000mm wide ,

for upto 33 kV

Nos 30.00 - -

e Supplying and fixing 440 V Danger Board. Nos 30.00 - -

6.9

Third Party Testing & commissioing (+Thermographics & relay coordinatiosn) of Panels , outlets, Cables etc & all other

electrical installation after commissioing, Vendor to submit atleast 3 Agencies name for this work.

Job 1.00 - -

6.10Testing of Earth pits at test links under witness of site

engineers to achive desired earth reisistances , genrating reports etc

Job 166.00 - -

6.11Liasoning , Documentations with supporting Drawings , test certificates & carrying of PWD/ Electrical Inspection /CEIG ,

the official fees will be born by clientJob 1.00 - -

7 LIGHTNING ARRESTOR

7.1SUPPLY , INSTALLATION & COMMSIOING OF EARLY

STREAMER EMISSION TYPE LIGHTENING ARRESTORS AS PER BELOW SPECIFICATION

Set 2.00

- -

Contd….23….

- 23 -


RateInstallation

RateSupplyAmount

InstallationAmount

a Supply of Early Streamer Emission (ESE) type Lightning - -

Protection complete with the Lightning Air Terminal - Configured as a Spheroid which is comprised of separate electrically isolated 4 panels (stainless steel) surrounding an earthed central finial.• Tested & certified as per NFC 17-102 standard “Switching Impulse Voltage” of -700 KV and “Direct Voltage” of -70 KV. The testing lab is IEC/IECEE accredited.• Tested & certified by CPRI (Central Power Research Institute), Govt of India for the Impulse current of 45 KA with 5 positive & 5 negative impulse. (Protection Radius = 79 mtrs @ Level I protection)

b LIGHTNING STRIKE RECORDER Supply of Lightning Strike Recorder - 7 digits electro mechanical display to record the lightning current in an IP 67 enclosure with the minimum sensitivity of 1500A & maximum capacity of 220 KA (8/20 micro second waveform). The recorder is of non-resettable type with the electro-mechanical display. • LCD screen is not permitted as it may depend upon the battery life to energize the LCD. • Tested & certified inline with the ese lightning arrester in an international laboratory for an impulse current of more than 450 KA as per IEC 60-1:1989 standard. • Tested & certified by CPRI (Central Power Research Institute), Govt of India for the Impulse current of 45 KA with 5 positive & 5 negative impulse.

- -

Contd….24….

- 24 -


RateInstallation

RateSupplyAmount

InstallationAmount

c

Supply Installation Testing &commissioning of 2Nos- Pipe-in -Pype type earth pits with 80 mm

dia, 3meters length pipe with specially developed on Pipe in pipe/Strip concept filled with highly

conductive & anticorrosive crystalline conductive mixture. The back fill is to be done

by special compound/Gel which retains moisture & enhance conductivity. The rate should be

inclusive of making bore & finish & terminated in chamber, masonry chamber with concrete

base, manhole, lockable cover Heavy Guage MS cover with frame (300 x 300 mm) For dedicated

Earth, make Ashlok/JK or equivalent

-

-

d

Mast Supply of G.I. mast of 5/7 mtrs height as per

requiremnet for mounting the terminal & adaptor with the ESE Air Terminal along with

supporting guy wires, with required MS fabrication / concrate foundtaion as per site

requirement etc.

-

-

e

Test Link JointSupply of weather proof thermoplastic

insulated, shock proof, dust & rust proof enclosure of suitable dimension.

-

-

Make : LPI/ Indelec / Eriko -

-

Contd…25….

- 25 -


RateInstallation

RateSupplyAmount

InstallationAmount

7.2

Supply, Installation, Testing & Commissioning of 1 c x 70 Sq.mm PVC insulated (19 stands of 1.8mm dia) copper conductor cable - Black or

Green insulated

Mtr 160.00

- -

TOTAL FOR LIGHTNING ARRESTOR - -

8 HT WORK - -

8.1 Vacuum Circuit Breaker- BEFORE TRANSFORMER as per below specs Set 4.00 - -

Supply, Installation, Testing & Commissioning of VCB as per below specs - -

11kV, 800A, 26.3kA for 3 sec with spring charging motor of 230V AC, tripping coil & closing coil suitable for 24V DC - -

Current Transformers - -600/1-1 A, CL 1 / 5P10 , 7.5VA for each core - -

Potential Transformer - -11000/√3 // 110/√3 V, CL 1/3P, 50VA - -

Relay - -AVAJH13 - Master Trip Relay - Ashida - -

MC61AnX - Feeder Protection Relay - (3O/C+1E/F -IDMT+Inst.) - L&T or eq Schnider / Siemens - -

TCS01-nX - Trip Circuit Supervision Relay - L&T or eq Schnider / Siemens - -

AVA33 - Auxliary relay for Transformer faults - Ashida - -Meters - -

Contd….26….

- 26 -

SR Description Unit Qty Supply Installation Supply Installation

No Rate Rate Amount AmountDigital Ammeter - -Digital Voltmeter - -

Digital Multifunction Meter (VEGA, Model-A, Cl-1, w/o RS485) - L&T or eq Schnider / Siemens - -

Miscellaneous - -8 Window annunciator in each panel with common Hooter - -Powerpack with inbuilt battery backup - 230V AC // 24V DC - -

Fuses - -Panel illumination Lamp - -

Plug & Socket - -L/R switch - -TNC Switch - -Thermostat - -

Panel space heater assembly - -Emergency Push Button - -

Indicating lamp - -Makes : L&T / Siemens/ABB/Schnieder - -

8.2 HT CABLE - -

a

Supplying , erecting & terminating 3 x 300 sq mm 11 kV, XLPE(E) ROUND armoured cable on wall/ceiling or laid in

provided trench / pipe in an approved manner as per specification No. CB-HT

Mtr 100.00 - -

b

Supplying , erecting & terminating 3 x 185 sq mm 11 kV, XLPE(E) ROUND armoured cable on wall/ceiling or laid in

provided trench / pipe in an approved manner as per specification no. CB-HT

Mtr 100.00 - -

Contd……27….

- 27 -


RateInstallation

RateSupplyAmount

InstallationAmount

8.3 HT CABLE TERMINATION ( Heat shrinkable type) - -

a

Supply, installation testing commissioing of Indoor type termination for above 3CORE, 300sqmm cable with cable

gland, indoor type cable sealing kits, insulation tape, approved sealing epoxy compund , effecting gland &

termination connections to the equipments complete as required.

SET 4.00 - -

b

Supply, installation testing commissioing of Indoor type termination for above 3CORE, 185 sqmm cable with cable

gland, indoor type cable sealing kits, insulation tape, approved sealing epoxy compund , effecting gland &

termination connections to the equipments complete as required.

SET 4.00 - -

Make : 3M/Rechyam - -TRANSFORMER - -

8.4 3500KVA ONAN OUT DOOR TYPE TRANSFORMER - -Design , manufacturing, supplying, Transporting, of

3500kVA ,3 phase, 50 c/s ONAN, copper wound transformer with delta conn. on HV side & star connection on LV side with

additional neutral brought out on load side, voltage rating 11 / 0.415kV with HV tapping of +5 To - 15% @ 1.25 ON

Load Tap Changer Switch with RTCC +AVR panel , continuously rated for full load with standard accessories

complete with Test Certificate

SET 4.00 - -

Ratio: 11/0.415 KV , 50 Hz, 3 phase, DYN-11 - -Capacity: 3500 KVA (Out Door type) - -

Contd……28…..

- 28 -


RateInstallation

RateSupplyAmount

InstallationAmount

Losses :No Load = 4300w max & Full Load = 25,500W max with IS tolerance - -

% Impedance = 7.15% - -H.V. Side: Cable end box suitable for 3.0 core x 300sq.mm 11 KV

XLPE (E) cable terminations - -

L.V. Side: Cable/ BBT - -1 set of Oil Temperature indicator - -

Buchholz Relay - -MOG For oil level with Low level alarm - -

Breather with silica gel - -Standard accessories like Explosion proof Vent, Oil Drain Valve,

Rollers, Liftings lugs, Topping of oil etc - -

The transformer described above complete with wiring upto Mashalling Box and as per final direction and approval of

Consultant/owner- -

The Rate Shall Also includs - -1- Testing of Transformer at manufacturer works , traveling expences for 4 person to be considered including Airfair & lodging / boarding as per the requiremnet.

- -

2- Loading of Transformer at manufacturing works , packing & forwarding at site including all taxes , duties , insurance etc - -

3- Unloading of transformer at site with necessary unloaing equipments & other necessary tools & tackels. - -

4- manufacturer should asist during testing & commisiong at site - -

Contd…..29…

- 29 -


RateInstallation

RateSupplyAmount

InstallationAmount

5- Installation , testing & commisooing of RTCC panel by Transformer Supplier's Engineer. - -

Cost should be inclusive for Type tests to be carried out at works for all Transfomer - -

Temperature Rise Tests - -Sound Level Tests - -Impuse Tests - -Partial Discharge Test - -12hours Heat run test with actual loading on transformer @ full load on all transformer - -

- -

8.5

Unloading, handling, installation & testing commissioning of Transformer with RTCC installation , Termination of control cabling etc & technical assistance for Installation of transfomer to other Elect Vendor

SET 4.00 - -

PREFERRED MAKES: VOLTAMP/KIRLOSKAR/UNIVERSAL-POWER /CROMPTON - -

- -TOTAL FOR HT WORK - -Partial Discharge Test - -

SCHEDULEintra.itiltd-india.com/bgp/tenders/new bill of quantities... · Web viewAmount c 1Core 150...

Documents

Transcript of SCHEDULEintra.itiltd-india.com/bgp/tenders/new bill of quantities... · Web viewAmount c 1Core 150...