Bialla Sp. z oo · 2018-10-21 · BGA (see ), adapter caps for BGA (Metcal) 160 ' 200 ' 160 mm,...
Transcript of Bialla Sp. z oo · 2018-10-21 · BGA (see ), adapter caps for BGA (Metcal) 160 ' 200 ' 160 mm,...
706 soldering kit
Cat. No. 202420
712 soldering kit
Cat. No. 202350
SPECIFICATIONFEATURES
FEATURES
<2 Ω
Soldering station
temperature range200 ~ 480 ° C
power supply 50 200 ~ 240V / 60Hz
The tip-to-ground voltage <2 mV
The resistance of the tip-to-ground
Panel dimensions ( W ' D ' H)Panel dimensions ( W ' D ' H)Panel dimensions ( W ' D ' H)Panel dimensions ( W ' D ' H)Panel dimensions ( W ' D ' H)Panel dimensions ( W ' D ' H)
panel Weight
Equipment: Flask "hot air" (connected to the panel of the station), the soldering iron
with a tip TI, the support of the soldering iron, the support flask "hot air" cord, cap:
A1300, A1121, A1124 Optional nozzles (cap) supply type QFP , SOP, PLCC SOJ,
BGA (see www.biall.com.pl), adapter caps for BGA (Metcal)
160 ' 200 ' 160 mm, about 160 ' 200 ' 160 mm, about 160 ' 200 ' 160 mm, about 160 ' 200 ' 160 mm, about 160 ' 200 ' 160 mm, about
3.4 kg
• Two switches allow you to work separate or shared soldering
station and the station "HOT AIR".
• Optional attachments allow you to work with SMD type SOIC,
CHIP, QFP, PLCC, BGA, etc.
• The high efficiency of heat transfer to the soldering tip heater or
heated air.
• Temperature control in a closed loop
• High power for fast heating of air temperature and
achievement of stability regardless of flow rate.
• Swirling air in the heating element provides improved heat
transfer from the heater.
• A wide range of air flow control.
• The "auto sleep" automatic heater cooled to 100 ° C and
turning the power off to save energy and extend the life of
the heating element.
• Immediate return to the set operating parameters after
removing the flask from the cradle.
• Status message "sleep" on the LCD.
• Messages of malfunctions on the LCD.
• Wide range of tips for soldering station (caves as the station
ESD 236 Quick - see page 9 of catalog).
• Large selection of adapters to a flask for hot air (as a cap Quick
855PG - see www.biall.com.pl
• It can also be used for removing paint, melting heat, etc.
disinfection.
• Station settings are password protected.
• Temperature control using the buttons.
• A temperature sensor disposed within the tip.
• Digital temperature calibration.
• Temperature control in closed loop.
• Electromagnetic heating element.
• The "auto sleep".
• Powerful brushless motor with variable.
• The "shut-off" Cooling element for heating the deposition of the
flask to stand.
• Well insulated, yet lightweight stock.
Power / voltage heater 50W / 30V
Station "HOT-AIR"
temperature range 100 ~ 450 ° C
Power / voltage heating 580W / 30V
Air flow 100 l / min max
digital display LCD resolution of 1 ° C
Other specifications
Universal cap a "pipe"
Type A1300
Ø8,4x17
Type A1121
Ø6,4x17
Ø3,0x25
SPECIFICATION
<2 Ω
Soldering station
temperature range
Operating Temperature The temperature in
the sleep mode
50 ~ 500 ° C
100 ~ 500 ° C 50
~ 250 ° C
Station "HOT-AIR"
Air flow 120l / min max
Power consumption
Power consumption
90W
Sleep mode time 0 ~ 250 min
temperature stabilization
temperature stabilization
± 2 ° C
± 2 ° C
Potential tip to ground
1000W
tel./fax: +48 58 322 11 91 E-mail:
http://www.biall.com.pl
Bialla Sp. z oo
ul. Barniewicka 54c PL
80-299 GDANSK