Best-Rite 3' x 4' Evolution Projection Board with Deluxe Aluminum Trim

Instruction Manual

Which board assembly instructions should you use?

Use L-Clip instructions for... Use Z-Clip instructions for...Ultra Trim

Presidential Trim

31 Trim

Euro Trim

Scroll down for instructions.

ABC Trim

Aluminum Trim

Deluxe Wood Trim

48 Trim

3/4

Determine board location. Measure from floor tothe top edge of board. Mark with pencil line thecorner location. Measure down from top edge ofboard 3/4”, and draw line as shown. Locate studnear each end of board and drill pilot hole along lineusing 1/8” drill bit.

Lift, Tilt, and SlideBoard down over theZ-Hangers.Z-Hangers shouldcatch in the top trim onthe back of the board.Draw line alongbottom edge of board.

Secure board to bottombrackets (F) using 2 shortscrews (B) as shown.

Attach Z-Hangers (E) using Long Screws (A) as shown.

Board Location

Board Location

Top Edgeof Board

Wall Stud

Draw line

Z Brackets hang inthe trim on back ofboard

118

Lift and remove board from the Z-Hangers.Measure up from bottom line of board 1-1/8”, anddraw line as shown. Locate stud near each end ofboard and drill pilot hole along line using 1/8” drill bit.

Draw line

Board Location

Bottom Edgeof Board

Drill Hole

Secure 2 bottom brackets (F) to the wall using 2long screws (A) as shown.Hang board on the Z-Hangers (E).

Hardware List

A Long Screw

B Short Screw

C Screw Anchor - Concrete

D Screw Anchor - Drywall

E Z Hanging Bracket

F Bottom Bracket

P1 Board

Parts List

Z Clip Install_05-29-13

(For Drywall)

(For Concrete walls)

E

AP-1

P-1

FA

P-1

B

F

Z Clip Install

Note:Install Masonry Anchors (D) into 1/4”Diameter predrill holes for masonrywalls.

Install Drywall Anchors (E) into 1/4”Diameter predrill holes for sheet rockwalls. E

D

1.

2.

3.

4.

5. 6.

Z Clip Install Instructions

1

1 14

1

2

3

4

5 6

Determine board location. Measure from floor to the bottom edge of board. Mark with pencil line thecorner location. Measure up from bottom edge ofboard 1-1/4” and draw line as shown. Locatestud near each end of board and drill pilot holesalong line using 1/8” drill bit.

Set board on the AngleBrackets. Draw line alongtop edge of board.Attach ½ the # of Angle Brackets using

Long Screws (B) as shown.

Board Location

Board Location

Bottom Edge of Board

Wall Stud

Draw line

Lift and remove board fromthe angle brackets. Measure down

from top line of board 1” and draw lineas shown. Locate stud near each end ofboard and drill pilot hole along line using

1/8” drill bit.

Draw line

Board Location

Top Edge of Board

Drill Holes

Secure top Angle Brackets (A) to the wall usinglong screws (B) as shown. Follow diagram inStep 1. Set board on the bottom angle brackets.

Hardware List

A Angle Bracket

B Long Screw

C Short Screw

D Screw Anchor-Concrete

E Screw Anchor-Drywall

P1 Board

Parts List

L Clip Install_12-12-14

Secure board to bottom andtop brackets (A) using shortscrews (C) as shown.

EquallySpaced

L Clip Install

Note:Install Masonry Anchors (D) into 1/4”Diameter predrill holes for masonrywalls.

Install Drywall Anchors (E) into 1/4”Diameter predrill holes for sheet rockwalls. E

D

3” 16” min.24” max.

Edge ofBoard

Angle Bracket Locations on Board

AngleBracket

Edge ofBoard

See diagram below.

L Clip Install Instructions

AttentionPlease read and follow these instructions!Failur e to follow these instructions willvoid your warranty and could result inboard failur e and possible injury.

1. Always use the correct supplied mounting hardware forthe type wall your board will be mounted on.

2. Use the correct stated predrill for the type anchor you will be using.

3. The Angle Brackets and Z Clips be installedaccording to the layout and spacing as shown below.

MUST

L-Clip_09-08-15

NOTE: For more information, please referto our web-site:

www.partsandinstructions.com

WWW.MYBINDING.COM

Your top and bottom L-Cliplayouts should be spaced likethis for an 8’ wide board.

If you don’t use this number ofL-Clips on top and bottom, yourboard could end up like this. Pleasefollow these installation directions.

Proper L-Clip Layout