BESSER/AMG ENHANCED ADJUSTABLE BOX CULVERT FORM · 2017-12-28 · BESSER/AMG ENHANCED ADJUSTABLE...
2
BESSER/AMG ENHANCED ADJUSTABLE BOX CULVERT FORM Besser acquired AMG in December 2016 7/8” Round Rubber used to improve seal between form and pallet Vibrator Pads are machined after welding for a true flat mounting surface 3/4” Joint Plate Bolts used to increase clamping force Formed Funnels add structure to perform as the header frame stop CNC Machined Renewable Alignment Dowel Second Vibrator on Rise Side of Form Reduces Corner Soft Spots Lift Hole Pins feature self purging receptacle (optional) 5/8” Grade 50 Joint Plates Fully Machined Pallet Guides, with renewable wear plate “push and pull” to allow for ease of set up Pallet Latch Relief Design so latches DO NOT have to be disassembled to remove Vibration Transfer Bar aids in compaction and surface finish Vibrator Pads have CNC machined plate with the correct hex hole pattern welded to the back for ease of assembly CNC Machined Finger Slots Pick Up Points for corner pick up Pick Up Points for joint plate pick up 5/16” Grade 50 Skin Machined Bores are honed to allow the latch to operate freely Pallet Latch redesigned to be opened with a 2-1/2” open end wrench Integral Locking System remove a common fail point Rubber gasketed adjustable box culvert equipment provides producers with the ultimate in flexibility. The size of the form can be increased and decreased to produce a wide range of product sizes to meet market requirements. Reducing your inventory of forms, producing products to exacting dimensions and improving employee safety during production process are significant benefits of using Besser/AMG forms for producing Box Culverts.
Transcript of BESSER/AMG ENHANCED ADJUSTABLE BOX CULVERT FORM · 2017-12-28 · BESSER/AMG ENHANCED ADJUSTABLE...
BESSER/AMG ENHANCED ADJUSTABLE BOX
CULVERT FORM
Besser acquired AMG in December 2016
7/8” Round Rubberused to improve seal
between form and pallet
Vibrator Pads aremachined after
welding for a trueflat mounting
surface
3/4” Joint Plate Boltsused to increase
clamping force
Formed Funnels addstructure to perform asthe header frame stop
CNC Machined RenewableAlignment Dowel
Second Vibrator onRise Side of Form Reduces
Corner Soft SpotsLift Hole Pins feature
self purging receptacle(optional)
5/8” Grade 50 Joint Plates
Fully Machined Pallet Guides, with renewable wear plate“push and pull” to allow forease of set up
Pallet Latch Relief Designso latches DO NOThave to be disassembledto remove
Vibration Transfer Bar aids in compaction and surface finish
Vibrator Pads have CNC machined plate with the correct hex hole pattern welded to the back for ease of assembly
CNC Machined Finger Slots
Pick Up Points forcorner pick up
Pick Up Points for joint plate pick up
5/16” Grade 50 Skin
Machined Bores are honed to allow the latch to operate freely
Pallet Latch redesigned to be opened with a 2-1/2” open end wrench
Integral Locking System remove a common fail point
Rubber gasketed adjustable box culvert equipment provides producers with the ultimate in flexibility. The size of the form can be increased and decreased to produce a wide range of product sizes to meet market requirements. Reducing your inventory of forms, producing products to exacting dimensions and improving employee safety during production process are significant benefits of using Besser/AMG forms for producing Box Culverts.
111 S. George StreetSioux City, Iowa 51103 USA+1.712.277.8111 or +1.870.336.3339 [email protected]
For better viewing, all guards, safety devices and signs are not necessarily shown. Some of the equipment shown or described throughout this brochure is available at extra cost. Besser Company reserves the right to change or improve product design and specifications without prior notice. Since the time of printing, some of the information in this brochure may have been updated, ask your Besser sales representative for details. 07
17-w
eb
Discover the Besser/AMG Difference
Typical Adjustable Core, Pallet and Header Assembly (core top not shown)
Typical Pallet Extensionavailable in 1ʼ, 2ʼ and 3ʼ
lengths (6ʼ length optional)
Enhanced Design DoubleAdjustable Basic Core Corner
common basic sizes 4ʼ x 2ʼ,6ʼ x 3ʼ and 9ʼ x 4ʼ for dry cast
production method (customsizes available upon request)
Typical Wall Spacer Extensionavailable in 1ʼ, 2ʼ and 3ʼ
lengths (6” length optional)
Double Adjustable Cast Steeland Fully CNC Machined
Header Assembly6” or 8” wall standard(optional header wall
spacers available)
Typical Header Extensionavailable in 1ʼ, 2ʼ and 3ʼ
lengths (6” length optional)
Double Adjustable CastSteel and Fully CNC MachinedUniversal Pallet Corner
Adjustable PalletHaunches (optional)
Core Extensionavailable in standard1ʼ, 2ʼ, 3ʼ, 4ʼ, 5ʼ and 6ʼ widths (6” wide optional)
Adjustable Core Haunches(optional)
Optional Bolt-On CastSteel Fully CNC MachinedHeader Wall Spacers(available for 7”, 7-1/2”,10” and 12” slab/wallthickness production)
Adjustable Header Haunches(optional)
* Basic Size is the smallest product size that can be produced on this mold set** Not available for wet cast mold equipment
NOTE: The “minimum wall” shown is for the production of precast box culverts with ASTM C1677 rubber gasket joints. Standard ASTM C1433 and ASTM C1577 TS, BS and SW thickness is available for the production of mastic joint box culvert elements.
Typical Mold Dimensions for Besser/AMG Adjustable Box Culvert Molds with Enhanced DesignBasic Size
*Typical
MaximumDry Cast
Form StripDry Cast
Static CastWetCast
6”Haunch
8”Haunch
12”Haunch
AdjustableHaunch
4ʼLength
6ʼLength
8ʼLength
MinimumWall
MaximumWall
3ʼ x 2ʼ 8ʼ x 8ʼ X X X X 8”4ʼ x 2ʼ 8ʼ x 8ʼ X X X X X 8”4ʼ x 3ʼ 8ʼ x 8ʼ X X X X ** X 8”6ʼ x 3ʼ 12ʼ x 12ʼ X X X X X X X X 8” 12”9ʼ x 4ʼ 12ʼ x 12ʼ X X X X X X X X 10” 12”9ʼ x 4ʼ 20ʼ x 12ʼ X X X X X X X 10” 12”
Metric sizes available1 m x 1 m 4.5 m x 4.5 m X X X 1200 mm X 2.5 m 1200 mm 1400 mm
