Begin
description
Transcript of Begin
![Page 1: Begin](https://reader036.fdocuments.us/reader036/viewer/2022062800/5681427a550346895daea1ea/html5/thumbnails/1.jpg)
Begin
EZ-GO DCS CART TROUBLESHOOTING
![Page 2: Begin](https://reader036.fdocuments.us/reader036/viewer/2022062800/5681427a550346895daea1ea/html5/thumbnails/2.jpg)
GENERAL WIRING DIAGRAM
Next
![Page 3: Begin](https://reader036.fdocuments.us/reader036/viewer/2022062800/5681427a550346895daea1ea/html5/thumbnails/3.jpg)
TECHNICAL ASSISTANCE
Solenoid Does Not Close
Solenoid Closes But No Travel
Vehicle Travels in reverse when in forward direction, and in forward when in reverse direction.
![Page 4: Begin](https://reader036.fdocuments.us/reader036/viewer/2022062800/5681427a550346895daea1ea/html5/thumbnails/4.jpg)
PRIOR TO CONTINUED TROUBLESHOOTING THE FOLLOWING STEPS MUST BE TAKEN
1. POSITION THE CART ON LEVEL GROUND AND BLOCK FRONT TIRES TO PREVENT VEHICLE FROM ROLLING.
2. ELEVATE THE DRIVE TIRES FROM THE GROUND.
My vehicle is safely lifted from the ground.
![Page 5: Begin](https://reader036.fdocuments.us/reader036/viewer/2022062800/5681427a550346895daea1ea/html5/thumbnails/5.jpg)
1. Tow/Run switch in the “Run” position.
2. Key switch in the “ON” position.
3. Forward/Reverse selector in “Forward” direction.
4. Place Foot pedal switch in fully accelerated position.
OK
![Page 6: Begin](https://reader036.fdocuments.us/reader036/viewer/2022062800/5681427a550346895daea1ea/html5/thumbnails/6.jpg)
Using a digital voltmeter with the Black Lead on battery negative, battery positive should be measured on the following pins of the controllers 10-pin wiring harness.
PIN 10 - RED/YELLOW WIRE
PIN 9 - RED WIRE
PIN 6 - YELLOW WIRE
PIN 5 - GREEN WIRE
If battery positive is not measured click the arrow of the corresponding wire.
All of these wires measure battery positive.
![Page 7: Begin](https://reader036.fdocuments.us/reader036/viewer/2022062800/5681427a550346895daea1ea/html5/thumbnails/7.jpg)
Pin 10 is supplied through your Run/Tow switch, verify this connection.
Back
![Page 8: Begin](https://reader036.fdocuments.us/reader036/viewer/2022062800/5681427a550346895daea1ea/html5/thumbnails/8.jpg)
Pin 9 is supplied from the Red wire on your For/Rev switch, verify this connection.
Back
![Page 9: Begin](https://reader036.fdocuments.us/reader036/viewer/2022062800/5681427a550346895daea1ea/html5/thumbnails/9.jpg)
Pin 6 is supplied from the Yellow wire on your Solenoid Coil, verify this connection.
Back
![Page 10: Begin](https://reader036.fdocuments.us/reader036/viewer/2022062800/5681427a550346895daea1ea/html5/thumbnails/10.jpg)
Pin 5 is supplied from the Green wire through your accelerator, verify proper operation of accelerator start switch.
Back
![Page 11: Begin](https://reader036.fdocuments.us/reader036/viewer/2022062800/5681427a550346895daea1ea/html5/thumbnails/11.jpg)
The solenoid is closed by the following steps
Next
![Page 12: Begin](https://reader036.fdocuments.us/reader036/viewer/2022062800/5681427a550346895daea1ea/html5/thumbnails/12.jpg)
First battery positive is supplied to the solenoid coil through the Run/Tow Switch, For/Rev Switch, and Key Switch.
Next
![Page 13: Begin](https://reader036.fdocuments.us/reader036/viewer/2022062800/5681427a550346895daea1ea/html5/thumbnails/13.jpg)
At this point battery positive should be measured on the Yellow/White wire.
Next
![Page 14: Begin](https://reader036.fdocuments.us/reader036/viewer/2022062800/5681427a550346895daea1ea/html5/thumbnails/14.jpg)
The solenoid is closed by Pin 7, the Blue Wire being pulled to ground.
Next
![Page 15: Begin](https://reader036.fdocuments.us/reader036/viewer/2022062800/5681427a550346895daea1ea/html5/thumbnails/15.jpg)
Verify that the Blue wire, Pin 7 is pulled low to activate the solenoid.
Pin 7 is being pulled low
Pin 7 is NOT being pulled low
![Page 16: Begin](https://reader036.fdocuments.us/reader036/viewer/2022062800/5681427a550346895daea1ea/html5/thumbnails/16.jpg)
Replace vehicle solenoid
End
![Page 17: Begin](https://reader036.fdocuments.us/reader036/viewer/2022062800/5681427a550346895daea1ea/html5/thumbnails/17.jpg)
At this point it is determined that your controller is faulty. Contact Flight Systems Industrial Products at 1-800-333-1194 to order a replacement controller.
End
![Page 18: Begin](https://reader036.fdocuments.us/reader036/viewer/2022062800/5681427a550346895daea1ea/html5/thumbnails/18.jpg)
1. Tow/Run switch in the “Run” position.
2. Key switch in the “ON” position.
3. Forward/Reverse selector in “Forward” direction.
OK
![Page 19: Begin](https://reader036.fdocuments.us/reader036/viewer/2022062800/5681427a550346895daea1ea/html5/thumbnails/19.jpg)
Measure the voltage of the Black Wire, Pin 2. This point should measure between 13-15V.
Pin 2 measures between 13-15V.
Pin 2 does not measure between 13-15V.
![Page 20: Begin](https://reader036.fdocuments.us/reader036/viewer/2022062800/5681427a550346895daea1ea/html5/thumbnails/20.jpg)
Measure the voltage of the White Wire, Pin 1. This point should vary from .4V - 1.6V with the accelerator pedal.
Pin 1 does vary between .4V – 1.6V when moving the accelerator pedal.
Pin 1 does not vary between .4V - 1.6V when moving the accelerator pedal.
![Page 21: Begin](https://reader036.fdocuments.us/reader036/viewer/2022062800/5681427a550346895daea1ea/html5/thumbnails/21.jpg)
Inspect/Replace accelerator pedal
End
![Page 22: Begin](https://reader036.fdocuments.us/reader036/viewer/2022062800/5681427a550346895daea1ea/html5/thumbnails/22.jpg)
Swap positions of the F1 and F2 cables on your controller, this will correct travelling in the wrong direction.
End