It is designed for maximum performance. Please seek advice if one is not familiar with this kindof electric powered precision model. Operating this model without prior preparation may causeinjuries. Remember, safety is the most important thing. Always keep this instruction manual athand for quick reference.

Warning ! This model is not a toy.

THE WINGS MAKERFACTORY PRE-FABRICATEDALMOST-READY-TO-FLY (ARF) SERIESMADE IN CHINA

* Specifications are subject to change without notice.*

www thewingsmaker com. .

Wing Span:40 in / 1020 mmWing Area: 310 sq in / 20 sq dmFlying Weight: 28 6 oz / 810 gFuselage Length: 36 in / 910 mmRequires: 4- channel radio w/ 4 micro servos,

20A Brushless ESC and 3 cells 11 1V2100 mAh Li Po battery charger.

-

.

.&

SpecificationsSpecifications

GE030

Before commencing assembly please read these instructions thoroughly , .

I NSTRUCTI ON M ANUAL

LITTLE TONI EP

BEFORE YOU BEGIN

INDEXBEFORE YOU BEGIN

PARTS LIST

ASSEMBLY

SAFETY PRECAUTIONS

P.1

P.2

P.3-P.9

P.9

Apply epoxy glue. Apply instant glue(C.A.glue, super glue.)

Ensure smooth non-bindingmovement while assembling.

Cut off shaded portion.

Must be purchased separately!Apply thread locker

Do not overlook this symbol!

Assemble left and rightsides the same way.

Pierce the shaded portioncovering film.

Peel off shaded portioncovering film.

Drill holes with the specifieddiameter (here: 3mm)

Pay close attention here!

Read through the manual before you begin, so you will have an overall idea of what to do.

Check all parts. If you find any defective or missing parts contact your local dealer. PleaseDRY FIT and check for defects for all parts that will require CA or Epoxy for final assembly.Any parts you find to be defective after the gluing process may be difficult to remove forwarranty replacement. The manufacturer will replace any defective parts, but will not extendto the parts that are good before gluing to defective parts during assembly. Warranty willnot cover any parts modified by customer.

Symbols used throughout this instruction manual comprise of the following :-

1

2

3

3mm

P.1

LITTLE TONI EP

6. SCREW PB2x10mm -- 2 pcs CLEVIS -- 1 pc. FUEL TUBE d2xD4x4mm -- 1 pc. HORN -- 1 set PUSHROD Ø1.4x427mm w/ Threads (For Rudder) -- 1 pc.

7. CLEVIS -- 1 pc. FUEL TUBE d2xD4x4mm -- 1 pc. PUSHROD Ø1.4x418mm w/ Threads (For Elevator) -- 1 pc.

8. SCREW PM3x6mm -- 4 pcs WASHER d3xD7mm -- 4 pcs FOLDING PROPELLER SET (PL6314020) -- 1 set COWLING -- 1 pc. SCREW PWA2x8mm -- 4 pcs SPINNER Ø45mm -- 1 set

9. BATTERY TIE 200mm -- 1 pc. FUEL TUBE d2xD4x4mm -- 2 pcs STRAPER -- 2 pcs SPONGE 10x50x150mm -- 1 pc. DOUBLE-SIDED TAPE 30x35mm -- 1 pc.

10. SCREW PM2.5x20mm -- 2 pcs WASHER d2.6xD8mm -- 2 pcs PVC PLATE 1x20x68mm -- 1 pc.(For Wing Protection)

11. CANOPY -- 1 pc. SCREW PWA2x8mm -- 4 pcs

12. DECALS: GE030DEC -- 1 pc.

Parts List

P.2

COVERING:--LIGHTEX SGX 100 WHITELIGHTEX SGX 312 BRIGHT RED

1. MAIN WING -- 1 pair

2. SERVO MOUNTING PANEL -- 1 pair SCREW PB2x12mm -- 4 pcs SCREW PA1.7x8mm -- 8 pcs STRAPER -- 2 pcs CLEVIS -- 2 pcs HORN -- 2 sets FUEL TUBE d2xD4x4mm -- 4 pcs PUSHROD Ø1.4x93mm w/ Threads (For Aileron) -- 2 pcs

3. MAIN LANDING GEAR -- 1 pair SCREW PWA2x10mm -- 6 pcs MAIN WHEEL Ø40mm -- 2 pcs WHEEL PANTS -- 1 pair COLLAR Ø3.1mm w/ set screw -- 2 sets SCREW PM3x25mm -- 2 pcs SCREW PWA2x6mm -- 4 pcs M3 NUT -- 2 pcs WASHER d3xD7mm -- 4 pcs COPPER TUBE d3.1xD4x4mm -- 2 pcs PLATE 0.5mm -- 1 pair

4. STABILIZER & ELEVATOR -- 1 set FUSELAGE -- 1 pc. ELEVATOR LINK PL4510010 -- 1 pc. SCREW PB2x8mm -- 2 pcs

5. VERTICAL FIN & RUDDER -- 1 set TAIL LANDING GEAR -- 1 set TAIL WHEEL Ø23mm -- 1 pc. PLASTIC COLLAR d1xD5x2mm -- 2 pcs SCREW PA2x8mm -- 2 pcs SCREW PM2x8mm -- 1 pc. M2 NUT -- 1 pc. ALUMINUM PLATE 0.3mm -- 1 pc.

Main Wing

Bottom View

Bottom View

Aileron Servos

Apply instant type CA glue to both sides of each hinge.

Aileron Servo Lead

Please choose either 02L & 02R or 03L & 03R or 04L & 04R that suits your servo.

Clevis

Horn

Fuel Tubed2xD4x4mm

PB2x12 mm Screw

PB2x12mm

PA1.7x8mm Screw

Ø1mm pilot holes for The Wings Maker horn are pre-drilled. Please look for pin-hole marks at under side of control surfaces.

Straper Fuel Tubed2xD4x4mm

PA1.7x8mm

PushrodØ1.4x93mm

P.3

4

8

2

1

02L

03L

04L

02R

03R

04R

Completed

PWA2x6mm

1mm

PM3x25mm Screw

d3xD7mm Washer4

3.1mm Wheel Collar2

2

M3 Nut2

PWA2x10mm Screw6

PWA2x6mm Screw4

PWA2x10mm

Stabilizer & Elevator

Main Landing Gear

Completed

Apply instant type CA glue to both sides of each hinge.

PB2x8mm Screw2

PB2x8mm

Wheel Pant

Ø1mm pilot holes for The Wings Maker tri-horn are pre-drillde. Please look for pin-hole marks at under side of control surfaces.

P.4

4

3

A A'

A=A'

(Main Wing)

(Stabilizer)B B'

B=B'

Temporary install the mainwing, adjust leveling of the stabilizer to make it as parallel to the main wing as possible

Bottom View

PM3x25 mm

Plate 0.5mm

d3xD7mmWasher

Wheel Ø40mm

3mmSet Screw

3.1mm Collar

M3 Nut Copper Tubed3.1xD4x4mm

Ø1mm pilot holes for The Wings Maker horn are pre-drilled. Please look for pin-hole marks at under side of control surfaces.

Rudder Pushrod

Vertical Fin, Rudder & Tail Landing Gear

Bottom View

Completed

Apply instant type CA glue to both sides of each hinge.

PA2x8mm Screw2

PB2x10mm Screw2

C C'

C=C'

1mm

P.5

6

5

Plastic Collar

Wheel 23mmPA2x8mm

M2 Nut PM2x8mm

Ø

M2 Nut1

PM2x8mm Screw1

PB2x10mm

Clevis

Horn Fuel Tubed2xD4x4mm

PushrodØ1.4x427mm

75mm 24mm

PM2x12mm Screw

PM3x6mm

PM2x12mm

PM2x12mm

d3xD7mm Washer d3xD7mm Washer

M5 Nut

PWA2x8mm Screw

PWA2x8mm

4

2

PM3x6mm Screw4

4

Don’t over-tighten the PM2 screws, let the propeller blades align themselves whenspinning.

Don't over-tighten the PM3 screws, too much stress on the screws could split the firewall.

Outrunner Motor 28/ 30 KM0283010

Propeller Adaptor (d3xD5) HW2340100

Elevator Pushrod

Outrunner Motor/ Cowling

Bottom View

Completed

Make sure rotating motor casing is not in contact with wirings or anything.

P.6

7

8

60mm35mm

Spinner Ø45mm

1.5mm

Optional Parts

Clevis

Fuel Tubed2xD4x4mm

Pushrod Ø1.4x418mm

SolderSolder

TWMKP0011310

PM2.5x20mm Screw

PM2.5x20mm

d2.6xD8mm Washer

d2.5xD8mm Washer

2

2

PVC Plate 1x20x68mm

Radio Equipment

Main Wing

Bottom View

Top View Completed

Bottom View

Front

Sponge Fuel Tubed2xD4x4mm

Elevator PushrodØ1.4x418mm

Rudder PushrodØ1.4x427mm

Receiver

Straper

Elevator Servo

Battery Battery Tie

Rudder Servo

20A Brushless ESC

Double-Sided Tape

Install and arrange the servos as shown in the diagram.

P.7

9

10

2.5mm

4

Adjust the wing and fuselage configuration as shown in the diagrams.

A=A' B=B'C=C' D=D'

A A'

B B'

D'D

C C'

Canopy

Wing Setting

PWA2x8mm Screw

P.8

11

12

1.2mmPWA2x8mm

# First time flyer should never fly by himself / herself. Assistance from experienced flyer is absolutely necessary.

# Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly pre-adjusted aircraft.

# is specially designed to be powered by 180W Motor System.

# Make sure the air field is spacious, never fly the plane too close to people and never get too close to a running propeller. Extreme caution should be exercised when working with electric powered models. Make sure the propeller is cleared of all objects, especially your hands before connecting the battery to the model. Make sure you understand the operation of the ESC (Electronic Speed Control) by studying the ESC manual. Once you plug in the battery for electric powered model, always treat the propeller as a rotating one, as accidental movement of the throttle stick will spin the propeller and could cause injuries.

# If you find wrinkles on the covering as a result of weather changes, you can use hot iron to remove the wrinkles. Please begin with lower temperature setting and gradually raise the temperature until the wrinkles are gone. Too hot an iron may damage the covering. Don't use hot iron near the seams or edges, hot iron will melt the glue and shrink the covering at the same time, causing the seams to pull away.

# Check and re-tighten up all factory assembled screws, use thread locker if necessary.

C.G. The ideal C.G. position is 74mm (2.9 in.) behind the leading edge measured at where the wing meets the fuselage. In order to obtain the C.G. specified, add weight to the fuselage or move the battery position. Check the C.G. before flying.

74mm

C.G.

2.9 in

P.9GE030PO18130809

14

Warning!Important Safety Precautions

Control Throws Adjust the control throws as shown in thediagram. These throws are good for generalflying. You can adjust according to yourpersonal preference.

Elevator

Rudder15mm15mm

10mm

6mm6mm

10mm

Aileron

13

LITTLE TONI EP

THE WINGS MAKER

www.thewingsmaker.com

GE030PO18130809