be modified to conform with local codes, conditions and...

Fast. Easy. Customer Focused.®Literature Disclaimer: Presentations in this brochure or any other Chicago Metallic Corporation publication are correct to the best of our knowledge at time of preparation. We provide this information in an advisory capacity only. Any advisory recommendations given in our publications must be modified to conform with local codes, conditions and specifications. We reserve all rights to amend any information published in our literature without additional notice. Chicago Metallic can not be held responsible or liable for the selection nor application of our products.

Photography by: J.K. Lawrence Photography and Dustin Shores Photography

Ceiling Systems and Specialty Products - USA and Canada: 800-323-7164 / Fax: 800-222-3744 / www.chicagometallic.combelgium / denmark / the netherlands / uk / germany / france / hong kong / prc / malaysia / united arab emirates / mexico

Chicago Metallic and its logo are Registered Trademarks of Chicago Metallic Corporation. © 2010 Chicago Metallic Corporation All Rights Reserved Printed in USA CAP-bRoC-0510

113995 r8 CMC_Broc_Cvr.indd 1 5/5/10 4:05:43 PM

Frisco convention centerFrisco, TX

chicago Metallic Products:EuroStone Sustainable Ceiling PanelsSeismic 1200 Suspension Grid System

chicago Metallic headquarters Chicago, IL

chicago Metallic Product:Ultraline™ Suspension Grid

Bethesda MeMorial hosPitalBoynton Beach, FL

chicago Metallic Products:Infinity Perimeter TrimSeismic 1200 Suspension Grid System

More than a slogan, it’s plain and simply the Chicago Metallic way of meeting customer needs world-wide. Since1893, our valued customers have depended on our suspension grid, metal ceiling and ceiling panel systems to bring their creative projects to life. The ceiling projects featured in this catalog are, in many cases, the award-winning and painstaking results of our customers endeavors to meet their client’s needs. We invite you to take a look inside, as we hope you will be equally inspired.

Right:

sacred heart ParishWeymouth, MA

chicago Metallic Product:Drywall Grid/SpanFast™

Center:

Merle norMan cosMeticsNaperville, IL

chicago Metallic Products:EuroStone® Sustainable Ceiling PanelsTempra™ Grid Suspension System

FAST. EASy. CUSToMEr FoCUSED.®

GrID METAL PANEL

General Applications

Perimeter trim

Premium

Special Applications

Curvilinear Acoustical

Drywall Applications

Plank and Panel

Utility

Seismic Applications

Linear Controlled Environment

open Plenum

Security

cMc headquartersChicago, IL

chicago Metallic Products:EuroStone Kalypso! Sustainable Ceiling PanelsUltraline Suspension Grid

aMerican exPress corPorate headquartersMinneapolis, MN

chicago Metallic Product:Planostile Metal Panels

hillier architecturePhiladelphia, PA


ZerMatt resortMidway, UT

chicago Metallic Product:Drywall Grid

The demand for green building designs are on the rise, it is therefore critical that your projects utilize products that incorporate the use of high recycled content material. Chicago Metallic is committed to providing industry-leading HrC products, in all ceiling categories. our HrCmax™ ceiling grid system includes 81% recycled steel in a variety of distinct profiles.

SEISMIC SoLUTIoNS – INTEGrAL CoMPoNENTS oF A BETTEr BUILT ENvIroNMENT.

Though suspended ceilings are considered non-structural, recommendations for seismic stabilization do exist, and Chicago Metallic has developed ICC recognized systems that can save up to 75% in material and labor costs.

Chicago Metallic’s Seismic Grid Systems are a cost-effective solution that includes seismic and fire-rated seismic constructions to satisfy all seismic code requirements while permitting direct upward access to mechanical systems.

HIGH rECyCLED CoNTENT…For GENErATIoNS To CoME

GrID SUSPENSIoN SySTEMS

Chicago Metallic’s preeminent position in the metal ceilings market is unparalleled. CMC’s broad array of curving, linear, flat metal, perimeter treatment and open plenum designs give the designer the tools to create projects that span from the simple to the sublime. Architects and designers have also trusted in CMC’s ability to produce metal ceiling products that are aesthetically pleasing, installer friendly and compliant with the most stringent standards for safety and durability. Chicago Metallic’s expansion of metal ceiling product lines to include more planks, downward accessible systems, decorative wire mesh and resin panel systems, offer the design community even more choices to meet stringent budgets.

teZa technologiesChicago, IL

chicago Metallic Products:SpanAir™ Plank Metal Ceiling SystemInfinity™ Perimeter Trim

METAL CEILINGS – FroM THE SIMPLE To THE SUBLIME!

METAL CEILING SySTEMS hyatt regencyChicago, IL


heartland PayMent systeMs service centerJeffersonville, IN

chicago Metallic Products:CurvGrid Ceiling SystemInfinity Perimeter TrimBeamGrid®

WilloWcreek coMMunity churchSouth Barrington, IL

chicago Metallic Products:Infinity Perimeter TrimPlanostile Metal Panels

teZa technologiesChicago, IL

chicago Metallic Products:SpanAir Plank Metal Ceiling SystemInfinity Perimeter Trim

university south Florida – Marshall student centerTampa, FL

chicago Metallic Product:Planar® Linear Metal Ceiling with MetalWood Finish

Bethesda MeMorial hosPitalBoynton Beach, FL

chicago Metallic Products:Infinity Perimeter TrimSeismic 1200 Suspension Grid System

Today’s fast track construction cycles require the support of manufacturer’s who can deliver quality products in a pinch. Chicago Metallic’s Quick Ship programs have saved the day for project managers from coast-to-coast. Designed with the best features but in a simple color palette, Quick Ship products slash as much as 80% off the stand lead times to get product to a project fast and easy!

chrysler PlantMarysville, MI

chicago Metallic Products:CurvGrid™ Ceiling SystemPlanostile™ Metal PanelsInfinity Perimeter Trim

QUICK SHIP ProGrAMS – For A FAST PACED WorLD

METAL CEILING SySTEMS

No matter the effect you seek for your ceiling design, Chicago Metallic is uniquely capable of bringing it to life. We recognize the value of offering contrasting colors or the visual impact of uniformity in color from one ceiling component to another; our colors and laminates will do this and more. With our broad range of painted and metallic colors, laminates, and wood grain finishes, your design is in good hands.

Right:

christiana MallNewark, DE

chicago Metallic Products:Planar MacroPlus Linear Metal Ceiling with MetalWood finishSpanAir Plank Metal Ceiling SystemInfinity Perimeter TrimPlanostile Metal Panels

Center:

BeneFis healthcareGreat Falls, MT

chicago Metallic Products:Planostile Metal PanelsCurvGrid Ceiling SystemInfinity Perimeter TrimMetalWood™ and custom wood finishes

CoLorS AND FINISHES – A BroAD PALETTE For INTErIor AND EXTErIor BEAUTy

METAL CEILING SySTEMS aBout FaMily FitnessCoral Springs, FL

chicago Metallic Product:CurvGrid Ceiling System

visitors inForMation BureauSan Antonio, TX

chicago Metallic Product:Traditions™ Embossed Ceiling Panels

Metro transit doWntoWn centeroklahoma City, oK

chicago Metallic Product:Planar Macro Linear Metal Ceiling with MetalWood Finish

chrysler PlantMarysville, MI

chicago Metallic Products:Planostile Metal PanelsInfinity Perimeter Trim

taylor-Morley hoMes design galleryChesterfield, Mo

chicago Metallic Product:BeamGrid

gruPo iMagen oFFice BuildingMexico City, MX

chicago Metallic Products:Intaline™ BaffleMagna™ T-CellInfinity Perimeter TrimPlanostile Metal PanelsEuroStone Sustainable Ceiling Panels

Schools, offices, retail projects, galleries and waiting rooms must all consider acoustical performance if they are to meet the well-being of the occupants. The fact is that managing acoustics in any built environment is essential to maximizing comfort, interpersonal communication or performance productivity. Today’s ceilings, through science can with optional features, help your project to support speech intelligibility or quell the clamor of a night time crowd.

oPEN PLENUM DESIGNS – A MINIMALISTS DrEAM CoME TrUE

Chicago Metallic open Plenum ceiling designs elevate the philosophy of “less is more” to an entirely new plane. Plenum masking, wire mesh panels in stainless or carbon steel and 360 degree painted suspension systems add life to ceiling spaces. Available in a wide array of configurations, open Plenum systems are a minimalists dream!

WinthroP university – thurMond auditoriuMrock Hill, SC

chicago Metallic Product:CurvGrid Custom Ceiling

ACoUSTICAL CorrECTIoN – BETTEr ENvIroNMENTS For LIvING, LEArNING AND LISTENING

METAL CEILING SySTEMS

As a critical building component that can affect light, air flow and acoustical performance, ceilings must also do their part to enhance indoor environmental quality. By design Chicago Metallic ceiling systems contribute to this important building factor by resisting sag, the formation of mold and mildew, and by avoiding the introduction of harmful fibers or voC’s to the environment. These benefits have contributed to the long-term value of not only LEED Certified projects but non-LEED projects as well.

CEILING PANEL SySTEMS THAT SUPPorT THE HIGHEST IAQ

CEILING PANEL SySTEMS

university oF texas – health science centerHouston, TX

chicago Metallic Products:EuroStone Sustainable Ceiling Panels (Novum)Tempra Grid Suspension System

dePaul university – ray Meyer centerChicago, IL

chicago Metallic Product:EuroStone Sustainable Ceiling Panels

dolPhins stadiuMMiami, FL

chicago Metallic Products:EuroStone Sustainable Ceiling Panels (Terric)Tempra Grid Suspension System

holiday innSkokie, IL

chicago Metallic Products:Monarch™ GE Ceiling PanelsTempra Grid Suspension System

Fast. Easy. Customer Focused.®Literature Disclaimer: Presentations in this brochure or any other Chicago Metallic Corporation publication are correct to the best of our knowledge at time of preparation. We provide this information in an advisory capacity only. Any advisory recommendations given in our publications must be modified to conform with local codes, conditions and specifications. We reserve all rights to amend any information published in our literature without additional notice. Chicago Metallic can not be held responsible or liable for the selection nor application of our products.

Photography by: J.K. Lawrence Photography and Dustin Shores Photography

Ceiling Systems and Specialty Products - USA and Canada: 800-323-7164 / Fax: 800-222-3744 / www.chicagometallic.combelgium / denmark / the netherlands / uk / germany / france / hong kong / prc / malaysia / united arab emirates / mexico

Chicago Metallic and its logo are Registered Trademarks of Chicago Metallic Corporation. © 2010 Chicago Metallic Corporation All Rights Reserved Printed in USA CAP-bRoC-0510

113995 r8 CMC_Broc_Cvr.indd 1 5/5/10 4:05:43 PM

USA and Canada: 800.323.7164 / fax: 800.222.3744 Infinity Perimeter Trim 1

perimeter trim09 53 13

Infinity™

product guide

Fast. Easy. Customer Focused.®

2 Infinity Perimeter Trim chicagometallic.com

03 Infinity™PerimeterTrim 04.......Quick Ship Program 05.......Infinity Engineered (Straight Edge) 06.......Infinity R (Reveal Edge) 06.......Infinity Z (Razor Edge) 06.......Accessories

07 ReflectedCeilingPlans

08 SystemIntegration

09 SpecificationData

10 InfinitySpecification 11 GeneralConditionsofSale

Contents

Product Updates

ColorSamples1. Custom color matching requires customer color sample

or paint manufacturer and color number.2. Chicago Metallic Corporation (CMC) will provide color

sample for approval upon request.3. Service Level begins after receipt of color approval.

OrderReviewCustomer Service direct: 1.800.323.7164 / option 1.

OrderPlacementOrders to be faxed to 1.866.211.3824.

StandardSamplesandLiteratureStandard literature, product samples and color samples are available from the CMC Sample and Literature department at no charge. Phone: 1.800.323.7164/ option 2Fax: 1.800.222.3744 Email: [email protected]

TechnicalSupportRequests for technical information on CMC Metal Ceilings may be placed with the Technical Services Department. Phone: 1.800.323.7164 option 3Fax: 1.888.329.2620Email: [email protected]

MockupsandCustomSamplesWhen CMC has agreed to provide custom samples or mockups, the cost for them will be billed to the account. CMC will issue credit for all mockups and custom sample invoices when valid orders for these products are placed with our Customer Service Department. Phone: 1.888.991.7070 Fax: 1.866.211.3824Email: [email protected]

ToPlaceOrdersPhone: 1.800.323.7164 option 1Fax: 1.866.211.3824

Service

chicagometallic.com/infinity

chicagometallic.comPRODUCT

UPDATES

Up-to-date, time stamped product information is always available on the web


ApplicationsIdeal for hospitals, hospitality, retail, airports, offices, schools. Create light coves, floating islands or accents.

Engineered, R (Reveal Edge) and Z (Razor Edge)Features• Infinity profiles are available in straight and curved

heights from 2 to 12.• Infinity R profile with continuous reveal.• Infinity Z simulates a 0 depth ceiling.• Attractive, smooth, rust- and distortion-free

perimeter.• Sturdy extruded aluminum.• Integrates with standard grid and other ceiling

systems.• Metal contains no organic compounds to support

mold and microbial growth.• “QuickShip” standard sizes, or engineered to project

specifications.• Straight or curved profiles can be paired for specific

applications.

• Available factory painted 180°, 360°, or with ready for field painting surface.

Infinity™

perimeter trim

11/163/4

H

Infinity Engineered

Infinity R(Reveal Edge)

H

3/4

2

6

Infinity Z (Razor Edge)

#430 Clip(2 pc)

Convex Curve

Ceiling Grid

Splice Plates


Product Dimensions PerOrder Number Length Height Face Feet Pieces Weight/LF

Trim (Splices and Clips not included - sold separately)Straight 01470Qxx 12 2 3/4 Per Order 0.25 01471Qxx 12 4 3/4 Per Order 0.55 01472Qxx 12 6 3/4 Per Order 0.92 01473Qxx 12 8 3/4 Per Order 1.1 01475Qxx 12 10 3/4 Per Order 1.42Note:Pricingdoesnotincludesplicesandclips.

FactoryMiteredCornerKits (unassembled)2 kit contains: Two (2) 12 Straight Trim pieces with mitered corners; one (1) Corner Splice; two (2) Straight Splices.4, 6, and 8 kit contains: Two (2) 12 Straight Trim pieces with mitered corners; two (2) Corner Splices; four (4) Straight Splices.10, and 12 kit contains: Two (2) 12 Straight Trim pieces with mitered corners; three (3) Corner Splices; six (6) Straight Splices.InsideCorners90° 01470IM01 1 2 3/4 Per Order 01470IM44 1 2 3/4 Per Order 01471IM01 1 4 3/4 Per Order 01471IM44 1 4 3/4 Per Order 01472IM01 1 6 3/4 Per Order 01472IM44 1 6 3/4 Per Order 01473IM01 1 8 3/4 Per Order 01473IM44 1 8 3/4 Per Order 01475IM01 1 10 3/4 Per OrderOutsideCorners90° 01470TM01 1 2 3/4 Per Order 01470TM44 1 2 3/4 Per Order 01471TM01 1 4 3/4 Per Order 01471TM44 1 4 3/4 Per Order 01472TM01 1 6 3/4 Per Order 01472TM44 1 6 3/4 Per Order 01473TM01 1 8 3/4 Per Order 01473TM44 1 8 3/4 Per Order 01475TM01 1 10 3/4 Per OrderFor 12 Corner Kits, see Accessories, pg. 6.

AccessoriesSplicePlate 414.00 Joins trim together Per OrderCornerSplicePlates 417.00 Joins trim at inside corners Per Order 429.00 Joins trim at outside corners Per OrderGridClip 430.00 Joins grid to panel (2 parts) Per Order

Straight Trim01470Q/01471Q /01472Q/01473Q/01475Q

Inside Corner 90°01471IM / 01472IM / 01473IM

Outside Corner 90°01471TM / 01472TM / 01473TM

Corner Splice Plates417-429

Grid Clip430

Splice Plate414

Quick Ship Program


Product Dimensions PerOrder Number Length Height Face Feet Pieces Weight/LF

SystemStraight–IncludesTrim,SplicePlatesandGridClips

01470S.xx 12 2 3/4 Per Order 0.25

01470S.xx 12 2 3/4 Per Order 0.25

01471S.xx 12 4 3/4 Per Order 0.55

01471S.xx 12 4 3/4 Per Order 0.55

01472S.xx 12 6 3/4 Per Order 0.92

01472S.xx 12 6 3/4 Per Order 0.92

01473S.xx 12 8 3/4 Per Order 1.1

01473S.xx 12 8 3/4 Per Order 1.1

01475S.xx 12 10 3/4 Per Order 1.42

01475S.xx 12 10 3/4 Per Order 1.42

1474S.xx 12 12 3/4 Per Order 1.84

1474S.xx 12 12 3/4 Per Order 1.84

Curved–IncludesTrim,SplicePlatesandGridClips

01470C.xx Varies 2 3/4 Per Order 0.25












Curved Trim01470C/01471C /01472C/01473C/01475C/1474C

Straight Trim01470S/01471S /01472S/01473S/ 01475S/1474S

Infinity™ Engineered (Straight Edge)


Product PerOrder Number Description Pieces Weight

PairedInfinityBracket 446.36.00 Joins Infinity 2 1/4 apart with 3/4 opening between panels Per Order 446.46.00 Joins Infinity 2 7/8 apart with1 3/8 opening between panels Per OrderNote:OnecliprequiredattopandatbottomofInfinitypanel,maximum24 oncenter.

HorizontalSplicePlate447.00 Adjustable Corner Splice Plate for Infinity Z Per Order

Accessories

Paired Infinity Bracket446.36.00

Horizontal Splice PLate447.00

Infinity R04571S/04572S

Infinity Z04770S

Infinity R and Z Product Dimensions PerOrder Number Length Height Face Feet Pieces Weight/LF

InfinityR(RevealEdge)Straight–IncludesPanels,SplicePlatesandGridClips 04571S.xx 12 4 3/4 Per Order 0.80*ServiceLevelappliesto01White,08Black,44SatinSilverMetallic.ServiceLevelis4forOtherColors.

InfinityZ(RazorEdge)Straight–IncludesPanels,SplicePlatesandGridClips 04770S.xx 12 11/2 6 Per Order 1.00Note:Cornersavailableminimum45degrees,maximum135degrees.


Reflected Ceiling Plans

Outsidecorner

Insidecorner

Ceilingsystem

Diagonalcorners

Gridtotrim

SpliceInfinity™Rperimetertrim

Outsidecorner

Insidecorner

Diagonalcorners

Gridtotrim

SpliceInfinity™Zperimetertrim

Ceilingsystem

Diagonalcorner

Diagonalcorner Splice

Infinity™perimetertrim

Outsidecorner

Insidecorner

Concavecurve

Convexcurve

CeilingsystemGridtotrim

Infinity Engineered

Infinity R (Reveal Edge)

Infinity Z (Razor Edge)


Grid to trim

430Gridclip

CeilingGrid

Trim

Grid and ceiling panel

Magna T-Cell

Planostile-lay-in square

Planostile-snap-in

Planostile-lay-in reveal

Infinity Engineered

System Integration

430Gridclip

CeilingGrid

Trim

Infinity R (reveal edge)


Magna T-Cell™

Planostile™ lay-in square

Planostile™ snap-in

Planostile™ lay-in reveal

CubeGrid™ and GraphGrid™

Grid to trim

430Gridclip

CeilingGrid

Trim

Grid to trim

Infinity Z (razor edge)


Paired Infinity atHanger Wire

Infinity Paired Trim


Specification DataProduct information for integration into ceiling specification

Infinity Infinity R Z Quick Engineered Reveal Razorsuspension type Ship

material extrudedaluminum • • • •

surface paintedonexposedsurfaces • • • •

painted360° (optional) • • •

primed

size heights: 2,4,6, 2,4,6 4 6 8,10 8,10,12

lengths:12standardandmadetoorder 12 • • •

straight • • • •

curvedtominimum18radius •

pairedoption •

fire classA:flame0,smoke0perASTME84 • • • •

performance standardtoharshinteriorenvironment • • • •

suspension 9/16,15/16,1-3/8 • • • •

concealedsnap-bar,drywall,linear • • • •

warranty 1yearlimited • • • •

sustainability 100%recycledpostconsumercontent, 100%locallyrecyclable • • • •

Standard Painted Colors 01White 08Black 44SatinSilver

Premium Painted Colors

21CopperMetallic 23Sandstone 379GlossWhite 386GlossBlack 431Whitewash 520PolarWhite 521Nickel 524Silver 510MorningDewMetallic 511AutumnMetallic 512MoonGlowMetallic 513SunGoldMetallic 514HarvestMetallic 515SterlingMetallic 516FlintMetallic 517EmeraldMetallicOther_____________________

ColorsWoodScenes™ Painted Colors

800LazyMaple

801AgedTeak

802VintageBurlwood

803BurnishedCherry

804SleekCherry

805WeatheredOak

Coordinating Solid Paint Colors toMetalWood® II Finishes

401Maple 402Oak 403Cherry 404PumpkinMaple 405Karri


SpecificationPART1-GENERAL1.01ScopeProvide metal suspension trim for ceiling island or fascia.1.02 Related SectionsA. Section 09 22 26 - Suspension SystemsB. Section 09 29 00 - Gypsum BoardC. Section 09 54 00 - Specialty CeilingsD. Section 09 58 00 - Integrated Ceiling AssembliesE. Section 13 48 00 - Sound, Vibration, and Seismic ControlF. Section 23 50 00 - Central Heating EquipmentG. Section 26 50 00 - Lighting

1.03ReferencesA. American Society for Testing and Materials (ASTM)

1. C423 - Sound Absorption and Sound Absorption Coefficients by the Rever-beration Room Method.

2. C635 - Standard Specification for the manufacture, performance, and testing of Metal Suspension Systems for Acoustical Tile and Lay-in Panel Ceilings.

3. C636 - Standard Practice for Installation of Metal Ceiling Suspension Systems for Acoustical Tile and Lay-in Panels.

4. E 84 - Test Method for Surface Burning Characteristics of Building Materials. 5. E 1264 - Classification for Acoustical Ceiling Products. 6. E 1477 - Standard Test Method for Luminous Reflectance Factor of Acoustical

Materials by Use of Integrating-Sphere Reflectometers.

1.04SubmittalsA. Product data sheets listing dimensions and standard compliance.B. Samples: Representative sample of color and finish of all exposed materials.C. Shop Drawings: Reflected ceiling plans to indicate trim locations, radii, and

part numbers.D. Approval drawings indicating ceiling layout and manufacturers details submitted

and approved prior to manufacture of components.

1.05ProjectConditionsA. Environmental Requirements:

1. Verify weather tightness of area to receive suspension system prior to instal-lation.

2. Installation to begin only when temperature and humidity conditions closely approximate interior conditions which will exist when area is complete and occupied.

3. Heating and air conditioning systems to be operating prior to, during, and after installation.

4. Deliver materials in manufacturers original packaging, unopened and undam-aged.

5. Store materials in an enclosed dry location at room temperature and protect from soiling, damage, moisture and humidity.

1.06MaintenanceFurnish additional material equal to _____ percent of ceiling area.

PART2-PRODUCTS2.01ManufacturersInfinity perimeter trim by Chicago Metallic, 4849 South Austin Ave, Chicago IL 60638. 1-800-323-7164.

2.02MaterialsA. Panels:

1. Manufactured from extruded 6063-T5 aluminum complete with continuous integral slots for attachment of splice plates and grid clips.

B. Profile:1. Infinity profile perimeter trim for T-bar type grid acoustical ceilings (2)(4)(6)

(8)(10)(12) inch high with 3/4 inch horizontal face. Panels to be (straight)(and)(curved) as indicated on approved drawings. (All corners to be factory mitered) (90 degree corner kits are allowed in place of mitered corners on straight sections). Finish to be factory applied painted finish (on outside surface)(360 degrees)(01 White)(other color ______).

2. Infinity R Reveal profile perimeter trim for T-bar type grid acoustical ceilings (4) inch high with 3/4 inch wide horizontal face and 1/2 inch wide x 3/4 inch deep continuous open reveal. Panels to be straight as indicated on approved drawings. All corners to be factory mitered. Finish to be factory applied paint (on outside surface)(360°)(01 White)(other color ______).

3. Infinity Z Razor profile for T-bar type grid acoustical ceilings, 6 inch wide hori-zontal face by 1-1/2 inch high. Panels to be straight as indicated on approved drawings. All corners to be factory mitered maximum 45 degrees. Finish to be factory applied paint on outside surface (01 White)(other color____).

C. Splice Plate:1. Manufactured from galvanized steel with set screw for splicing sections of

perimeter trim.D. Grid Clips:

1. Manufactured from galvanized steel with set screw for attaching perimeter trim to suspension system members.

E. Paired Bracket:1. Manufactured from electro-galvanized steel and used for back-to-back Infinity

installations. Size bracket to maintain panel vertical surfaces (2-1/4 inch apart with 3/4 inch opening at bottom) (2-7/8 inch apart with 1-3/8 inch opening at bottom) (____ inches apart).

PART3-EXECUTION3.01ExaminationExamine area receiving system to identify conditions which will adversely affect installation. Do not begin installation until adverse conditions have been remedied.

3.02PreparationA. Verify actual field dimensions prior to installation.B. Verify adequate support for Infinity Perimeter Trim prior to installation.C. Infinity for drywall sections to be cleaned on site prior to field painting.

3.03InstallationA. Infinity Perimeter Trim:

1. Install after completion of above ceiling work.2. Install ceiling suspension system as specified and in accordance with ASTM

C636.3. Install Infinity perimeter trim in accordance with manufacturers printed instruc-

tions and details and approved shop drawings.4. Infinity perimeter trim to be supported by ceiling grid suspension system.5. Attach splice plates and tighten set screws to join perimeter trim.6. Attach trim to main tees and/or cross tees with grid clips. Field measure and

cut tees to length. Attach grid clips to perimeter trim by inserting into grooves and firmly tighten set screw. Attach grid clips to main tees and cross tees with sheet metal fasteners (by contractor).

7. Field paint Infinity for drywall sections after drywall, taping, joint compound and sanding is complete.

3.04FieldQualityControlA. Maximum defection not to exceed 1/360 of the span.


General Conditions of SaleOrderAcceptanceWhenever used herein, “Seller” shall refer to Chicago Metallic Corporation and “Purchaser” shall refer to the party ordering or purchasing products (“Products”) from Seller.Seller’s price list does not constitute an offer to sell Products listed therein, but is simply provided as a convenience to prospective Purchasers.Purchaser’s order to Seller shall constitute an offer to Seller to purchase Products which offer Seller may accept at its sole discretion. Acceptance shall be by a writing containing these General Conditions of Sale (“Conditions”). Acceptance of Purchaser’s order or any part of it by Seller is expressly made conditional on Purchaser’s assent to these Conditions. Purchaser may vary these Conditions only with the written consent of Seller. Acceptance of Products by Purchaser or failure of Purchaser to object in writing to these Conditions within ten (10) days following delivery of Products to Purchaser shall constitute Purchaser’s assent to these Conditions.

ShipmentandDeliverySeller shall deliver Product F.O.B. place of shipment. Risk of loss to Product shall pass to Purchaser upon delivery to carrier at such place of shipment. Carrier acts as Purchaser’s agent. Products shall be shipped as soon as practical, or as requested by Purchaser after order acceptance by Seller. However, delivery dates shall not be of the essence, but shall be regarded as Seller’s best approximation of such delivery dates.

PricesofFreightCostsUnless otherwise indicated, prices shown on Seller’s price list are for less than truckload quantities. The minimum truckload quantity is 24,000 pounds. Prices are subject to change without notice and are based on full carton quantities. Prices shall be those in effect at time of shipment of Products.Seller shall grant Purchaser a freight allowance on all orders of 12,000 pounds or more for a single shipment to a single destination. The allowance shall be based on the lowest rates currently in effect from actual shipping point to destination point or nearest port of export. In no event shall the allowance be greater than the actual freight cost of a specific shipment. Purchaser’s request for costlier means of shipment will be honored, but Purchaser shall be liable to Seller for the additional freight expense. Purchaser “will-call” orders at Seller’s plant warehouse shall not be entitled to allowance.All taxes, tariffs, duties or similar charges paid by Seller imposed or levied by any governmental authority in connection with the purchase, shipment, import or export of Products purchased or in connection with the procuring of materials used therein may at Seller’s sole option be added to the price of Products so affected. Additional shipping charges for Products paid by Seller such as destination, storage, labor and redelivery and special or extra expenses for handling air freight, bus or other shipments may also, at Seller’s sole option, be added to the price of such Products.

PaymentPayment for all Products shall be net cash due and payable in U.S. dollars within thirty (30) days following receipt by Purchaser of shipping documents for such Products by check or bank transfer to a bank account to be designated by Seller. If accounts are paid within ten (10) days following receipt by Purchaser of the corresponding shipping documents, Purchaser shall been entitled to a one percent (1%) discount from the price of Products only.If, in Seller’s sole opinion, the financial condition of the Purchaser so warrants, Seller may require advance payments or satisfactory security. In the event that the Pur-chaser fails to make such advance payments or furnish such security upon Seller’s request, delivery of Products may be suspended without further Seller obligation.Seller may, at Seller’s sole option, require payment by means of an irrevocable letter of credit opened and confirmed by a bank or banks acceptable to Seller and upon terms and conditions acceptable to Seller.

LimitedWarrantySeller warrants to Purchaser that Products will substantially conform in quantity and quality to Purchaser’s order, as accepted by Seller, provided, however, that (1) Products are inspected by Purchaser upon arrival at place of destination and any and all nonconformities are noted on the bill of lading and all other delivery documents and are attested to in writing by carrier’s representative (2) Purchaser furnishes Seller with written notice of such non-conformities within fifteen (15) days following arrival of non-conforming Products at the place of destination, (3) Purchaser holds non conforming Products for Seller’s inspection (4) non-conformities occurred prior

to delivery by Seller of Products F.O.B. place of shipment, and (5) Purchaser does not alter, repair, use or attempt to alter or repair any non-conforming Products. This limited warranty is Seller’s only and exclusive express warranty to Purchaser. Seller disclaims any and all implied warranties including without limitation any implied warranty of merchantability or fitness for a particular purpose.Purchaser’s sole and exclusive remedy against Seller shall be the replacement F.O.B. its plant or site, at Seller’s option, of any Products which do not conform to Seller’s limited warranty hereunder. No other remedy (including, without limita tion, incidental or consequential damages for lost profits, lost sales, injury to persons or property or any other incidental or consequential loss) shall be available to Purchaser.Purchaser agrees to include in all contracts between Purchaser and subsequent owners or users of Products, and to bring to the attention of all Purchaser’s custom-ers of Products, the following warranty disclaimer: Chicago Metallic Corporation disclaims any and all warranties expressed or implied, including, without limitation, any implied warranty of merchantability or fitness for a particular purpose. Purchaser shall be excluded on behalf of Seller all remedies for damage or injury to Products persons or property. In the event that Purchaser fails to comply with the foregoing obligations, Purchaser shall indemnify Seller for any liability resulting from such non-compliance and shall otherwise hold Seller harmless.

ReturnsIn order to return any Products to Seller, Purchaser must first obtain prior authorization for products eligible for return, and receive a Return Goods Authorization number from Seller’s home office. All authorized returns are subject to a 20% restocking charge. Seller will only issue credit for Service Level “0” material received at the designated company facility with the Return Goods Authorization appearing on the material, and after being inspected and determined by Seller to be in resalable condition. Purchaser is solely responsible for arranging and prepaying for all return freight. Seller will not be responsible for any damage in transit on material returned at customer’s request, and will not file freight claims on such damaged material. When these terms are met, seller will issue appropriate material credit less the restocking charge.

Default,TerminationandSuspensionofDeliverySeller reserves the right, among other remedies, either to cancel Purchaser’s order or suspend further deliveries of Products thereunder in the event that (1) Purchaser fails to pay for any one shipment of Products when payment for such shipment becomes due; (2) Purchaser fails to make any advance payments or satisfactory security demanded by Seller pursuant to paragraph two of PAYMENTS section above; or (3) Purchaser fails or refuses to accept any delivery of Products ordered from Seller.Delivery of Products may be suspended in whole or in part in case of any event beyond Seller’s control, including, but not limited to, explosion, fire, shortage of fuel, power or raw materials flood strike lockout, injunction, riot, insurrection, war, national emergency, government act, or act of God.

MiscellaneousNo failure or delay on the part of Seller in exercising any right, power or privilege hereunder shall operate as a waiver thereof or of any other right, power or privi-lege hereunder nor shall any single or partial exercise of any such right power or privilege preclude any other right, power or privilege. The rights or remedies of Seller hereunder are cumulative and not exclusive of any rights or remedies which it may otherwise have.The parties hereto may correct stenographic and clerical errors without liability.Purchaser may not assign the order without the express written consent of Seller.All notices to be given hereunder by either party to the other party shall be dispatched by certified or registered mail return receipt requested addressed to the last known post office address of such other party. Any such notice shall be deemed received within five (5) days following any such dispatch if mailed from within the United States of America and ten (10) days if mailed from outside the United States of America. Either party may change its address by notice to the other party.These Conditions shall be governed by and interpreted in accordance with the laws of the State of Illinois, United States of America, and all disputes hereunder that cannot be amicably resolved by the parties thereto must be settled in a court of competent jurisdiction within the State of Illinois, United States of America.The provisions of these Conditions shall be severable one from the other so that should any provision be held legally unenforceable by a court of competent jurisdic-tion, the remaining provisions shall remain in effect.

12 Infinity Perimeter Trim chicagometallic.comLiterature Disclaimer: Presentations in this brochure or any other Chicago Metallic Corporation publication are correct to the best of our knowledge at time of preparation. We provide this information in an advisory capacity only. Any advisory recommendations given in our publications must be modified to conform with local codes, conditions and specifications. We reserve all rights to amend any information published in our literature without additional notice. Chicago Metallic can not be held responsible or liable for the selection nor application of our products.

Ceiling Systems and Specialty Products - USA and Canada: 800.323.7164 / Fax: 800.222.3744 / www.chicagometallic.combelgium / denmark / the netherlands / uk / germany / france / hong kong / prc / malaysia / united arab emirates / mexico

Chicago Metallic and its logo are Registered Trademarks of Chicago Metallic Corporation. Infinity, MetalWood and WoodScenes are trademarks of Chicago Metallic Corporation.© 2011 Chicago Metallic Corporation All Rights Reserved Printed in USA SNL0142A2011

M e t a l i n e™ / S e c u r l i n e®

P R O D U C T G U I D E

M

800.323.7164 | chicagometallic.com

METAL: Metaline™ › Securl ine® / 095753

Me

tali

ne

lock

-do

wn

Se

curl

ine

pla

nk

1516

342

T H E S A F E S T C H O I C E I S S O M E T I M E S T H E M O S T A E S T H E T I C

Meta l ine

APPLICATIONS

• Industry standard security ceiling providingaccess resistance in supervised areas.

FEATURES

• Range of panel sizes and material thickness.

• Washable baked-on enamel finish.

• Panels continuously lock under the bulb of heavy duty Metaline grid.

BENEFITS

• Meet strength and environmental requirements.

• Economical and durable.

• Adjust acoustical performance to providenoise control.

Secur l ine

APPLICATIONS

• Access and abuse resistant security ceilingfor unsupervised and supervised rooms andcorridors in correctional facilities.

FEATURES

• Galvanized steel in thickness from18 to 12 gage.

• Washable baked-on enamel finish, overlappingplanks and heavy duty channels.

BENEFITS

• Meets strength and environmentalrequirements.

• Adjust acoustical performance to providenoise control.

For more detailed product information, visit:

chicagometallic.com/metaline

chicagometallic.com/securline

Metaline Securline

Grid

Panel

PlankChannels

SAMPLE NO. 109R281D

Perforation Code Key

109 – Hole size in 1/1000 inches (0.109")

R – R = Round hole S = Square hole

281 – Hole spacing in 1/1000 inches (0.281")

D – D = Diagonal pattern (45°)L = Linear pattern (straight)S = Staggered pattern (60°)

109R281D(Metaline)

125R250D(Securline)

chicagometallic.com | 800.323.7164

Perforation Patterns (optional)

lock-down plank

Metaline

panel type

material

surface

size

edge

fire

sound

performance

suspension

classification

warranty

sustainability

2.02 PRODUCTS SPECIFICATIONS

Ac

co

us

tic

al

Se

cu

rity

Pa

ne

l C

eil

ing

s

painted 0.040" aluminum • •painted 20 gauge galvanized steel •painted 18 gauge galvanized steel • •painted 16, 14, 12 gauge galvanized steel •solid and perforated • •1' x 2', 2' x 2', 2' x 4' •1' x 10' standard, also non-standard lengths •square • •class A: flame 0, smoke 0 per ASTM E 84 • •NRC - perforated with 1 1/2" fiberglass acoustical pad 0.90 0.90

supervised areas • •unsupervised areas •interior applications • •exterior soffits 1 • •15/16" heavy duty Metaline grid •3 1/2" heavy duty channels •type XX, pattern C, G per ASTM E 1264 • •20 year limited • •75% - 100% recycled content, 100% locally recyclable • •

Securline

S T R E N G T H

M

1 - Consult with an engineer to evaluate the suitability of the system for the intended application.

Metal & Curved Ceilings

Mopen plenum / metal panel / linear metal / curved grid / metal baffles / perimeter trim / security

Acoustical, Sustainable & Sanitary PanelsP

perlite / fiberglass / glass reinforced gypsum / melamine / mineral fiber / fiber reinforced plastic /

vinyl face gypsum

Ceiling Grid Systems

Gtraditional / designer / performance / drywall / curved drywall / pre-finished drywall track / access doors

Trims & Reveals

Twall / corner / ceiling / base / door / window

Ceiling Systems and Specialty Products - U.S. and Canada: 800.323.7164 / Fax: 800.222.3744 / chicagometallic.comCHICAGO / BALTIMORE / LOS ANGELES / BELGIUM / DENMARK / THE NETHERLANDS / UK / GERMANY / FRANCE / HONG KONG / PRC / MALAYSIA / UNITED ARAB EMIRATES / MEXICO

Sample requests:

U.S. and Canada: 800.323.7164 (ext 4580) / Fax: 800.222.3744 / [email protected]

Chicago Metallic, its logo, and Securline are Registered Trademarks of Chicago Metallic Corporation. Metaline is a Trademark of Chicago Metallic Corporation.

Literature Disclaimer: Presentations in this brochure or any other Chicago Metallic publication are correct to the best of our knowledge at time of preparation. We provide this information in an advisory capacity only. Any advisory recommendations givenin our publications must be modified to conform with local codes, conditions and specifications. We reserve all rights to amend any information published in our literature without additional notice. Chicago Metallic can not be held responsible or liablefor the selection nor application of our products.

© 2004 Chicago Metallic Corporation All Rights Reserved MPG-Security-1004 Printed in USA

Symbol I.D. Key

Chicago Metall ic Product Categories

Listed by Underwriter’s Laboratories and/or ITS/Warnock-Hersey for use in fire rated assemblies.

Products have a limited warranty.

Unlimited array of Chicago Metallic and custom colors.

Manufactured from up to 100% recycled material or are recyclable.

Detailed product information is availablein reference binder.

open plenummetal ceiling

09 54 13Open PlenumMetal Ceiling Systemsproduct guide


2 Open Plenum chicagometallic.com

SystemSelection

03 MagnaT-Cell™OpenCell

04.......Panel Configurations 04.......Assembled Panels 05.......Suspension 06.......Accessories

07 Intaline™Baffle

08.......Baffles 09.......Suspension 10.......Accessories

11 CubeGrid™OpenPlenumGrid

12.......15/16 Face 360° (Stab Finished Components

13 BeamGrid™OpenPlenumBeam

14 MetalScapes™WireMeshPanels

16 GraphGrid™OpenWireCeilingPanel

16 SystemIntegration

17 SpecificationData

18 Specifications

18.......Magna T-Cell 19.......Intaline 20.......CubeGrid 20.......GraphGrid 21.......BeamGrid 22.......MetalScapes

23 GeneralConditionsofSale

Contents

Product Updates

ColorSamples1. Custom color matching requires customer color sample

or paint manufacturer and color number.2. CMC will provide color sample for approval upon request.3. Service Level begins after receipt of color approval.

OrderReviewCustomer Service direct: 1.800.323.7164 / option 1.

OrderPlacementOrders to be faxed to 1.866.211.3824.

StandardSamplesandLiteratureStandard literature, product samples and color samples are available from the CMC Sample and Literature department at no charge.

Phone: 1.800.323.7164/ option 2Fax: 1.800.222.3744 Email: [email protected]

TechnicalSupportRequests for technical information on CMC Metal Ceilings may be placed with the Technical Services Department.

Phone: 1.800.323.7164 option 3Fax: 1.888.329.2620Email: [email protected]

MockupsandCustomSamplesWhen CMC has agreed to provide custom samples or mockups, the cost for them will be billed to the account. CMC will issue credit for all mockups and custom sample invoices when valid orders for these products are placed with our Customer Service Department.

Phone: 1.888.991.7070 Fax: 1.866.211.3824Email: [email protected]

ToPlaceOrdersPhone: 1.800.323.7164 option 1

Fax: 1.866.211.3824

Service

chicagometallic.com/magnatcell

chicagometallic.com/intaline

chicagometallic.com/cubegrid

chicagometallic.com/beamgrid

chicagometallic.com/graphgrid

chicagometallic.com/metalscapes


UPDATES

Up-to-date, time stamped product information is always available on the web

USA and Canada: 800.323.7164 / fax: 800.222.3744 Open Plenum 3

ApplicationsIdeal for hospitals, hospitality, retail, airports, transit, galleries, offices.

Features• Flexibility in design choices, module

sizes and plenum masking.

• Tee grid based systems ensure module alignment and accept industry standard fixtures.

• Panels and suspension blend together visually.

• Metal contains no organic compounds to support mold and microbial growth.

• 100% random access to plenum.

• Sustainable: Steel: 25% minimum, alu-minum: 100% post consumer recycled content, 100% locally recyclable, global/regional manufacture.

Magna T-Cell™

Open Cell Ceiling

Web Cover

Cross Tees

Angle

Main Tee

Assembled PanelTop and Bottom Blades

9/16Blade

2

Suspension andWeb Cover

1 1/2

9/16

2

1 x 2Wall Angle

1

2 3/4

15/16

3/4 x 15/16Wall Angle

2 1/16

9/16

3/8

Edge Cap

9/16

Cell Size(square)

Cell

2

ColorandFinishOptions

StandardPaintedColors 01 White 08 Black 44 Satin Silver

PremiumPaintedColorsandFinishes 03 Bronze 21 Copper Metallic 23 Sandstone 88 Flat Black 113 Straw 167 Brick Red 174 Garnet 215 Forest Green 246 Federal Indigo 256 True Blue 263 Plum 270 Pearl Gray 379 Gloss White 386 Gloss Black 401 Maple* 402 Oak* 403 Cherry* 404 Pumpkin Maple*

405 Karri* 425 Wet Clay 428 Yellow Flash 429 Silver Lining 430 Beige Breeze 431 Whitewash 432 Blonde Wood 437 Midnight Blue 438 Royal Amethyst 442 Burgundy Brick 443 Toffee Fate 447 Cinnamon 449 Fortune Gray 455 Cocoa Shell 495 Cardinal Red 510 Morning Dew Metallic 511 Autumn Metallic 512 Moon Glow Metallic 513 Sun Gold Metallic 515 Sterling Metallic 516 Flint Metallic 517 Emerald Metallic 520 Polar White

521 Nickel 524 Silver

AnodizedFinishes 14 Chromecoat Anodized 16 Brasscoat Anodized 504 Satin Silver Anodized 509 Copper Coat Anodized

MetalWood®IIWoodgrainFinishes 650R Maple 651R Cherry 652R Pumpkin Maple 653R Oak 654R Karri 655R Bamboo (Panels and Web Covers Only

WoodScenes™PaintedColors 800 Lazy Maple 801 Aged Teak 802 Vintage Burlwood 803 Burnished Cherry 804 Sleek Cherry 805 Weathered Oak


UPDATES

* Coordinating Solid Paint Colors to MetalWood® II Woodgrain Finishes


Product Cell Panel Blade Blade Packaging Number Size Size Height Face Sq. Ft. Pieces Weight

PaintedAssembled*Panels–0.010GalvanizedSteel

36.22.003.xxx 3 x 3 2 x 2 2 9/16 40 10 31

36.24.004.xxx 4 x 4 2 x 2 2 9/16 40 10 30

36.22.006.xxx 6 x 6 2 x 2 2 9/16 40 10 20

36.24.006.xxx 6 x 6 2 x 4 2 9/16 40 5 20

36.22.008.xxx 8 x 8 2 x 2 2 9/16 40 10 15

36.24.008.xxx 8 x 8 2 x 4 2 9/16 40 5 15

36.44.012.xxx 12 x 12 4 x 4 2 9/16 80 5 20

ReflectiveAssembled*Panels–0.024Aluminum

46.22.003.xxx 3 x 3 2 x 2 2 9/16 40 10 29

46.22.004.xxx 4 x 4 2 x 2 2 9/16 40 10 22

46.24.004.xxx 4 x 4 2 x 4 2 9/16 40 5 22

46.22.006.xxx 6 x 6 2 x 2 2 9/16 40 10 13

46.24.006.xxx 6 x 6 2 x 4 2 9/16 40 5 13

46.22.008.xxx 8 x 8 2 x 2 2 9/16 40 10 8

46.24.008.xxx 8 x 8 2 x 4 2 9/16 40 5 8

46.44.012.xxx 12 x 12 4 x 4 2 9/16 80 5 13

* Does not include grid, web covers or wall molding.

Panel Configurations Magna T-Cell

2 x 2 Panel 2 x 2 Panel 2 x 2 Panel 2 x 2 Panel 3 x 3 Cells 4 x 4 Cells 6 x 6 Cells 8 x 8 Cells

2 x 4 Panel 2 x 4 Panel 2 x 4 Panel 4 x 4 Panel 4 x 4 Cells 6 x 6 Cells 8 x 8 Cells 12 x 12 Cells

PanelConfigurations

Assembled Panels Magna T-Cell


Product Dimensions Weight Number Length Height Face Per Piece

EdgeCap–FinishBothSides*forFree-FloatingApplications

36.10.916.xxx 10 21/16 9/16 x 3/8 2

EdgeCap–FinishOneSideOnly

46.10.916.xxx 10 21/16 9/16 x 3/8 2

WallAngle–FinishBothSides(onesideforreflective)

C3209.xxx 10 2 1 2

* 01 White/08 Black/44 Satin Silver Metallic/Premium/Other Painted Colors only.** Reflective/Anodized only.

9/16GridMainTee(HeavyDuty)

10.04.040.01CH 12 11/2 9/16 3

MainTee(IntermediateDuty)

10.04.000.xxxCH 12 11/2 9/16 3.6

CrossTees–Stab-in

10.04.014.xxxCH 4 11/2 9/16 1

10.04.022.xxxCH 2 11/2 9/16 0.5

Edge Cap36.10.916-46.10.916

Wall AngleC3209

Main Tee10.04.000.CH

Cross Tee10.04.014.CH

Cross Tee –No Slots10.04.022.CH

Magna T-Cell Suspension


Accessories Magna T-Cell

Product Per Carton Number Length Description Piece Weight

PaintedWebCovers–0.010GalvanizedSteel

38.40.907.xxx 2 With hanger holes 50 15

38.40.908.xxx 2 Without hanger holes 50 15



ReflectiveWebCovers–0.012Aluminum





Product Cell Maximum Packaging Number Size Height Hole Size Piece Weight

InfillPanelswithCutouts-FlushFit*

38.06.003.xxx 3 x 3 2 2.125 10 2

38.06.004.xxx 4 x 4 2 3.125 10 2

38.06.006.xxx 6 x 6 2 5.125 10 3

38.06.008.xxx 8 x 8 2 7.125 10 3

38.06.012.xxx 12 x 12 2 11.12 10 4

* Hole size and type (round or square) to be specified at time of order.

Web Cover38.40.907-38.40.909-48.40.907-48.40.909

Web Cover38.40.908-38.40.91048.

Infill Panel38.06


ApplicationsIdeal for hospitals, hospitality, retail, airports, transit,galleries, offices.



• Five distinct systems each with a wide range of sizes and finishes.




• Sustainable: Steel: 25% minimum, aluminum: 100% post consumer recycled content, 100% locally recyclable, global/regional manufacture.

Intaline™

Baffle Ceiling chicagometallic.comPRODUCT

UPDATES

AlignmentClip

Main Tee (4 O.C.

Cross Tee(4 O.C.

Web Cover (optional

AlignmentSleeve

Suspension Clip

Baffle

Round Base / V Base

AlignmentClip

Main Tee (4 O.C.V base suspension available for variable baffle spacing or indexed 4 or 6.

Cross Tee(4 O.C.

Web Cover (optional

AlignmentSleeve

Suspension Clip

Baffle

V Base

Round Base V Base Tees Angle

1 1/2

15/16

15/16

3/4

15/16

6, 8 or 10

4

9/16

Indexing Clip

3/43/8


Product Packaging Number Length LF Pieces Weight

SteelBaffle4VBase–0.020

48.50.004.xxx 12 Per Order

AluminumBaffles6RoundBase–0.032


8RoundBase–0.032


10RoundBase–0.032


4

9/16

3/8

Baffles Intaline™

Steel-V Base48.50.004

Aluminum-Round Base38.40.031-38-40.051-38.40.061

6, 8or 10

15/16

3/4



PremiumPaintedColorsandFinishes 03 Bronze 21 Copper Metallic 23 Sandstone 88 Flat Black 113 Straw 167 Brick Red 174 Garnet 215 Forest Green 246 Federal Indigo 256 True Blue 263 Plum 270 Pearl Gray 379 Gloss White 386 Gloss Black 401 Maple* 402 Oak* 403 Cherry* 404 Pumpkin Maple* 405 Karri* 425 Wet Clay 428 Yellow Flash 429 Silver Lining 430 Beige Breeze 431 Whitewash 432 Blonde Wood 437 Midnight Blue

438 Royal Amethyst 442 Burgundy Brick 443 Toffee Fate 447 Cinnamon 449 Fortune Gray 455 Cocoa Shell 495 Cardinal Red 510 Morning Dew Metallic 511 Autumn Metallic 512 Moon Glow Metallic 513 Sun Gold Metallic 515 Sterling Metallic 516 Flint Metallic 517 Emerald Metallic 520 Polar White 521 Nickel 524 Silver

AnodizedFinishes 14 Chromecoat Anodized** 16 Brasscoat Anodized** 504 Satin Silver Anodized** 509 Copper Coat Anodized**


* Coordinating Solid Paint Colors to MetalWood® II Woodgrain Finishes ** Finish on one side only


Product Dimensions Packaging Number Length Height Face Feet Pieces Weight

15/16Grid

CubeGridMainTee(IntermediateDuty)–Slottingis48O.C.

C1811Mxxx 12 11/2 15/16 300 25 73

CubeGridCrossTee–Stab-in

C1804Mxxx 4 11/2 15/16 200 50 49

IndexingVBaseCarrier

48.40.100.008 12 11/2 15/16 – 12 23

48.40.101.008 12 11/2 15/16 – 12 23

Note: Use for V Base Baffles. Notches space baffles. Baffles attached to carrier with #48.40.005.008 attachment clip.

CrossTeeforIndexingVBaseCarrier–Stab-in

C1210Mxxx 4 11/2 15/16 200 50 49

Product Dimensions PackagingNumber Length Height Face LF Pieces Weight

WallAngle–AluminumwithHemmedEdges

38.90.124.xxx 12 3/4 15/16 300 25 25

WallAngle–PaintedBothSides

C3209.xxx 10 2 1 – – 2

WebCover*–WithHangerHoles

38.40.909.xxx 4 2 9/16 1 0.50

WebCover*–WithoutHangerHoles

38.40.910.xxx 4 2 9/16 1 0.50

* Optional when used with standard grid.

Intaline™ Suspension

Main Tee C1811M

Cross Tee C1804M

Indexing V-base Carrier 48.40.100.008

Wall Angle38.90.124

Wall AngleC3209

Web Cover38.40.909

Web Cover38.40.910


Product Per Carton Number Description Pieces Weight

SuspensionClip

48.40.003.008 Steel baffle to 15/16 grid-08 Black 100 1

38.40.921.008 Aluminum baffle to 15/16 grid-08 Black 100 1

SwivelSuspensionClip

48.40.004.008 Steel baffle to 15/16 grid-08 Black 25 2

38.40.004.008 Aluminum baffle to 15/16 grid-08 Black 25 2

AlignmentClip(top)

48.40.002 Steel baffle-Clear 100 1

38.40.922 Aluminum baffle-Clear 50 1

AlignmentClip(bottom)

48.40.001 Steel baffle 100 1

IndexingSuspensionClip

48.40.005.008 V Baffle to Intaline Carrier 250 1

AlignmentSleeve(bottom)

38.40.923 Aluminum baffle 50 1

Accessories Intaline™

Suspension Clip48.40.003 - 38.40.921

Swivel Suspension Clip48.40.004 - 38.40.004

Indexing Suspension Clip48.40.005

Alignment Clip (top)48.40.002

Alignment Clip (bottom)48.40.001

Alignment Clip (top)38.40.922

Alignment Sleeve (bottom)38.40.923


ApplicationsIdeal for hospitals, hospitality, show-rooms, lobbies, corridors.






• No unnecessary holes in suspension web.

• Lowers total costs.

• 360 degree painting of all components.

• Sustainable: Steel: 25% minimum, aluminum: 100% post consumer recycled content, 100% locally recy-clable, global/regional manufacture.


UPDATES

CubeGrid™

Open Plenum Grid Ceiling

Cross Tee

Angle

Main Tee

48 x 4824 x 24

1 x 2Wall Angle

2

1

15/16 x 15/16Wall Angle

3/4

15/16

1 1/2WebCap

Tees

15/16



PremiumPaintedColorsandFinishes 03 Bronze 21 Copper Metallic 23 Sandstone 88 Flat Black 113 Straw 167 Brick Red 174 Garnet 215 Forest Green 246 Federal Indigo 256 True Blue 263 Plum 270 Pearl Gray 379 Gloss White 386 Gloss Black 401 Maple* 402 Oak* 403 Cherry* 404 Pumpkin Maple* 405 Karri* 425 Wet Clay 428 Yellow Flash 429 Silver Lining 430 Beige Breeze 431 Whitewash 432 Blonde Wood 437 Midnight Blue

438 Royal Amethyst 442 Burgundy Brick 443 Toffee Fate 447 Cinnamon 449 Fortune Gray 455 Cocoa Shell 495 Cardinal Red 510 Morning Dew Metallic 511 Autumn Metallic 512 Moon Glow Metallic 513 Sun Gold Metallic 515 Sterling Metallic 516 Flint Metallic 517 Emerald Metallic 520 Polar White 521 Nickel 524 Silver

AnodizedFinishes 14 Chromecoat Anodized** 16 Brasscoat Anodized** 504 Satin Silver Anodized** 509 Copper Coat Anodized**


* Coordinating Solid Paint Colors to MetalWood® II Woodgrain Finishes ** Finish on suspension face only



24x24ModuleMainTee-HeavyDuty–Slottingis24”O.C.

C1800KxxX 12 11/2 15/16 300 25 73

MainTee-IntermediateDuty–Slottingis24”O.C.

C1811KxxX 12 11/2 15/16 300 25 73

CrossTees-Stab-in

C1802KxxX 2 11/2 15/16 150 75 37

C1804KxxX 4 11/2 15/16 200 50 49

48x48ModuleMainTee-HeavyDuty–Slottingis48”O.C.

C1800MxxX 12 11/2 15/16 300 25 73

MainTee-IntermediateDuty–Slottingis48”O.C.

C1811MxxX 12 11/2 15/16 300 25 73

CrossTee-Stab-in

C1804MxxX 4 11/2 15/16 200 50 49


WallAnglesFinishOneSide-AluminumwithHemmedEdges

38.90.124.xxx 12 3/4 15/16 120 10 10

PaintedBothSides

C3209.xx 10 2 1 – – 2

*Reflective and Anodized finishes on one side only.

15/16 360° Finished Grid Components CubeGrid™

Main TeeC1800-C1811

Cross TeeC1802

Cross TeeC1804

Wall AngleC3209

Wall Angle38.90.122


Cross Beam

Perimeter Beam

Hanger/Coupler

Main Beam

Corner Kit

ApplicationsIdeal for hospitals, hospitality, retail, airports, transit, galleries, offices, cafeterias, lobbies.



• Five module sizes.

• Choose section and module to suit scale of space.



• Sustainable: Aluminum: 100% post consumer recycled content, 100% locally recyclable, global/regional manufacture.

BeamGrid™

Open Plenum Beam Ceiling

AvailableSizes• BeamGrid is available in the following beam sizes:

Standard (wide x high SpecialOrder(wide x high 1 x 1 1 x 5 1 x 2 2 x 6 1 x 4 2" x 8" 2 x 2 3 x 6 2 x 4 3 x 12 3 x 3 5 x 5 4 x 4 6 x 6

• BeamGrid is available in the following standard module sizes:

12 x 12, 16 x 16, 24 x 24, 36 x 36, 48 x 48

W

H

Beam

W

Wall Channel

H


UPDATES



PremiumPaintedColorsandFinishes 03 Bronze 21 Copper Metallic 23 Sandstone 88 Flat Black 113 Straw 167 Brick Red 174 Garnet 215 Forest Green 246 Federal Indigo 256 True Blue 263 Plum 270 Pearl Gray 379 Gloss White 386 Gloss Black 401 Maple*

402 Oak* 403 Cherry* 404 Pumpkin Maple* 405 Karri* 425 Wet Clay 428 Yellow Flash 429 Silver Lining 430 Beige Breeze 431 Whitewash 432 Blonde Wood 437 Midnight Blue 438 Royal Amethyst 442 Burgundy Brick 443 Toffee Fate 447 Cinnamon 449 Fortune Gray 455 Cocoa Shell 495 Cardinal Red 510 Morning Dew Metallic 511 Autumn Metallic 512 Moon Glow Metallic

513 Sun Gold Metallic 515 Sterling Metallic 516 Flint Metallic 517 Emerald Metallic 520 Polar White 521 Nickel 524 Silver

AnodizedFinishes 14 Chromecoat Anodized 16 Brasscoat Anodized 504 Satin Silver Anodized 509 Copper Coat Anodized


* Coordinating Solid Paint Colors to MetalWood® II Woodgrain Finishes


Cross Tee

Wall Angle

Main Tee

MetalScapes Panel

24 x 24 and 24 x 48 lay-in wire panel for use with 15/16 T-grid.

ApplicationsCreate durable, accessible, and airy ceilings in interior spaces.

Features• MetalScapes Wire Mesh panels

are constructed of stainless or carbon steel.

• 8 stainless steel panels — no painting.

• 6 carbon steel panels — paintable.

• Stainless steel and carbon steel panels are available in 24 x 24 or 24 x 48 nominal configuration for use in 15/16 grid.

• Factory applied no-VOC powder coated paints for carbon steel panels only.

Benefits• MetalScapes Wire Mesh panels may

contribute to LEED® certification project credits.

• Class A Fire Rating (Non-combustible material.

• From 10% to 25% recycled content; 100% recyclable at end of useful life.

MetalScapes™

Wire Mesh Panels


UPDATES

Aberdeen 60023

Armor 60031

Erlanger 60025

Lattice 60033

Frankfort 60027

Scales 60029

Appalachian 60015

Hood 60019

Alps 60016

Atlas 60020

Everest 60017

Ural 60021

Rockies 60018

Tyber 60022

StainlessSteelPatterns

CarbonSteelPatterns

Standard Painted Colors (Carbon Steel Patterns only)

01 White 08 Black 44 Satin Silver


1 x 1 Cell 2 x 2 Cell 3 x 3 Cell 4 x 4 Cell

ApplicationsIdeal for hospitals, hospitality, retail, airports, transit, galleries, offices, cor-ridors.

Features• Flexibility in design choices, cell sizes

and plenum masking.

• Designed to show consistent wire spacing, even at panel perimeter.

• Four designs with different wire spacing.

• Tee grid based systems ensure module alignment and accept industry stan-dard fixtures.



• Lowers total costs.

• Sustainable: Steel: 25% minimum lo-cally recyclable, global/regional manu-facture.

GraphGrid™

Open Wire Ceiling Panel

Cross Tee

Wall Angle

Main Tee

GraphGridPanel

24 x 24 lay-in wire panel for use with 9/16 and 15/16 T-grid.

Product Nominal Packaging Number Cell Size Panel Size Sq Ft Piece Weight

GraphGridPanels–For15/16and9/16T-Grid

8901.xxx 1 x 1 2 x 2 Per Order




Wire diameter: 0.117


Standard Painted Colors 01 White 08 Black 44 Satin Silver

Premium Painted Colors and Finishes 21 Copper Metallic 23 Sandstone 379 Gloss White 431 Whitewash 510 Morning Dew Metallic 511 Autumn Metallic

512 Moon Glow Metallic 513 Sun Gold Metallic 514 Harvest Metallic 515 Sterling Metallic 516 Flint Metallic 517 Emerald Metallic 520 Polar White 521 Nickel 524 Silver

Reflective Finish 58 Bright Mirror


UPDATES


System Integration Open Plenum

MagnaT-Cell™

Intaline™

BeamGrid™

GraphGrid™andMetalScapes™

Panel at Suspension Edge Cap 1 x 2 Wall AngleInfinity™ Perimeter Trim(Web Cover conceals fasteners)

15/16 x 3/4 Wall Angle

Baffle Parallel To Wall

Baffle Attachment Baffle AlignmentBaffle Perpendicular To Wall

Wall condition with 15/16 Angle Wall condition with 1 x 2 Angle

Infinity™ Perimeter TrimGrid Intersection

Panel at Grid

Panel at Wall Infinity™ Perimeter Trim

Wall Channel Wall Channel-double

Perimeter Beam Infinity™ Perimeter Trim

V Base Baffle inIndexing Carrier

CubeGrid™


Product information for integration into ceiling specification

panel type Magna T-Cell Intaline Round Base Intaline V Base

material depth 2 6, 8, 10 4

width 9/16 3/4 3/8

panel size/length 2 x 2, 2 x 4, 4 x 4 12 12

painted steel • • painted aluminum • reflective and anodized • one side only one side only anodized aluminum size spacing 3, 4, 6, 8, 12 6, 8, 10 4 variable variablefire class A: flame 0, smoke 0 • • • per ASTM E 84 performance interior applications • • •suspension 9/16 general • 15/16 general • • beam warranty 1 year limited • • •sustainability Steel: 25% minimum, aluminum: • • • 100% post consumer recycled content,100% locally recyclable global manufacture

Open Plenum Specification Data

panel type CubeGrid BeamGrid GraphGrid MetalScapes

material depth 1 1/2 1, 2, 3, 4 n/a n/a

width 15/16 1, 2, 3, 4 1, 2, 3, 4 various panel size/length 2 x 2 2 x 2, 2 x 4

painted steel • • • painted aluminum • stainless steel • reflective and anodized cap only • anodized aluminum

size spacing 24, 48 12, 16, 24 30, 36 48 1, 2, 3, 4 variousfire class A: flame 0, smoke 0 • • • • per ASTM E 84 performance interior and seismic environments • • • •suspension 9/16 general • 15/16 general • • • beam • warranty 1 year limited • • • •sustainability Steel: 25% minimum, aluminum: • • • 100% post consumer recycled content,100% locally recyclable global manufacture Aluminum: 100% post consumer • recycled content,100% locally recyclable global manufacture


Specification Magna T-Cell™ Open Cell

PART1-GENERAL1.01 Section Includes

Provide Open Cell Ceiling System.

1.02 Related Sections

A. Section 09 22 26 - Suspension Systems

B. Section 09 54 00 - Specialty Ceilings

C. Section 13 42 00 - Building Modules

D. Section 13 48 00 - Sound, Vibration, and Seismic Control

E. Section 23 50 00 - Central Heating Equipment

F. Section 26 50 00 - Lighting

G. Section 265000 Lighting1.03 References

A. American Society for Testing and Materials (ASTM



1.04 Submittals

A. Product data sheets listing dimensions, load carrying capacity and standards compliance.

B. Sample kit containing appropriate open cell ceiling samples.

C. Shop drawings illustrating appropriate placement of system.

D. Certification of materials and system conforming to specification requirements.

1.05 Project Conditions

A. Environmental Requirements:

1. Verify weather tightness of area receiving suspension system prior to instal-lation.

2. Wet trades work to be thoroughly dry and complete prior to installation.



1.06 Maintenance

Furnish additional material equal to ______ percent of ceiling area.

PART2-PRODUCTS2.01 Manufacturers

Magna T-Cell ceiling system as manufactured by Chicago Metallic, 4849 S. Austin Avenue, Chicago, IL, 1-800-323-7164.

2.02 Suspension System Components

A. Lay-In Panels:

1. Manufactured from (painted 0.010 inch galvanized steel (0.024 inch aluminum forming U-shaped blades 2 inches high by 9/16 inch wide by (24(48 inches long, notched to form (3 x 3(4 x 4(6 x 6(8 x 8(12 x 12 inch cells.

2. Finish: (Coated with baked-on polyester enamel paint; Color: (01 White(08 Black(44 Satin Silver(Other ____; Anodized (14 Chromecoat(16 Brasscoat(509 Coppercoat, Woodscenes (____, MetalWood II (____.

3. Panels: (24 x 24(24 x 48(48 x 48 inches, nominal size. Architect Note: 48 x 48 inch panel available for 12 x 12 inch cell only.

B. Suspension System Components:

1. Main Tees:

a. Manufactured from (0.018(0.020 inch steel 9/16 inch wide by 1-1/2 inches high by 144 inches long, with factory punched cross tee slots, hanger holes and integral bayonet-style end couplings.

b. Capping color and finish matches lay-in panels.

2. Cross Tees:

a. Manufactured from (0.012 (0.018 inch steel 9/16 inch wide, by 1-1/2 inches high by (24 (48 inches long, with factory punched cross tee slots, hanger holes, and staked-on end couplings.

b. Capping color and finish matches Main Tees.

3. Web Covers:

a. Manufactured from (painted 0.010 inch galvanized steel(0.012 inch alumi-num 2 inches high by 9/16 inches wide by (24(48 inches long, formed to a “U” shape, (with(without pre-punched hanger holes.

b. Color and finish matches panels.

4. Perimeter Treatment:

a. Wall angle:1. Manufactured from (0.020 inch steel(0.025 inch aluminum 2 inches high

by 1 inch wide by 120 inches long.2. Finish: (Painted both sides(Anodized on outer surface color matching

panels.b. Edge Cap:

1. Manufactured from (painted 0.020 inch galvanized steel(0.025 inch aluminum 2-1/16 inches I.D. by 3/8 inch wide top leg by 9/16 inch wide bottom leg.

PART3-EXECUTION3.01 Examination

Examine area receiving suspension system to identify conditions which will adversely affect installation. Do not begin installation until adverse conditions have been remedied.

3.02 Installation

A. Main Tees: Installed 48 inches on center, by direct suspension from existing structure, with not less than 12 gage steel hanger wires, wrapped tightly 3 full turns, spaced 48 inches on center along component length.

B. Web Covers: Installed on main runners during main runner installation.

C. Cross Tees:

1. Installed perpendicular to main tees (24(48 inches on center forming (24 x 48(48 x 48 inch modules.

2. Installed perpendicular to 24 inch by 48 inch module forming cross tees 24 inches on center forming 24 inch by 24 inch modules.

D. Perimeter Treatment

1. Wall angle: Installed on vertical surfaces intersecting suspension system by appropriate method in accordance with industry accepted practice.

2. Edge cap: Affixed to main tee and cross tee ends by (screw(pop rivet attach-ments.

3.03 Repair

A. Remove damaged components, replace with undamaged components. Clean with non-solvent based non-abrasive commercial cleaning solution.


2. Additional Hanger Wires at locations where imposed loads could cause deflection exceeding 1/360 span.

E. Air Diffusers: coordinate with Mechanical (HVAC Division.

3.03 Repair



Intaline™ Baffle Specification

PART1-GENERAL1.01 Scope

Furnish and install the Intaline metal baffle open plenum ceiling system as manu-factured and supplied by Chicago Metallic Corporation.



B. Section 09 53 00 - Acoustical Ceiling Suspension Assemblies

C. Section 09 54 00 - Specialty Ceilings

D. Section 09 58 00 - Integrated Ceiling Assemblies

E. Section 13 48 00 - Sound, Vibration and Seismic Control

F. Section 23 00 00 - Heating, Ventilating and Air Conditioning

H. Section 26 50 00 - Lighting

1.03 References


1. C 635 - Standard Specification for the manufacture, performance, and testing of Metal Suspension Systems for Acoustical Tile and Lay-in Panel Ceilings.

2. C 636 - Standard Practice for Installation of Metal Ceiling Suspension Systems for Acoustical Tile and Lay-in Panels.

3. E 84 - Test Method for Surface Burning Characteristics of Building Materials.

1.04 Submittals

A. Product data: Manufacturers standard data sheets listing dimensions and details.

B. Samples: Manufacturers standard samples including suspension, panels and colors.

C. Shop Drawings: Reflected ceiling plan and elevation drawings indicating ceiling layouts, dimensions and perimeter conditions.

D. Certification1. Furnish certification of materials and system conforming to specification

requirements.2. Provide written warranty against defective workmanship and materials for a

period of __ year(s (up to 20 yrs. maximum from filing notice of completion.




2. Wet trades work to be thoroughly dry and complete prior to suspension system installation.






Intaline metal baffle open plenum ceiling system as manufactured by Chicago Metallic Corporation, 4849 South Austin Avenue, Chicago, Illinois 60638. 1-800-323-7164.

2.02 ComponentsA. Baffle Panels:

1. Manufactured from (0.020 inch steel (0.032 inch aluminum nominal (4 (6 (8 (10 inches deep by 144 inches long, with (round (diagonal V base. Architect Note: Nominal 4 inch deep panel available in steel with diagonal V base only. Nominal (6 (8 (10 inch deep panels available in aluminum with round base only.

2. Finish: (coated with baked-on polyester enamel painted finish on both dies, Color: _______, Anodized on one side, color _______, (WoodScenes painted color _______.

B. Suspension System Components:

1. Main Tees:

a. Manufactured from 0.015 inch steel 15/16 inch wide by 1-1/2 inches high by 144 inches long, with factory punched cross tee slots, hanger holes and integral bayonet-style couplings.

b. Finish on cap to be (08 Black(________.

2. Cross Tees:

a. Manufactured from 0.015 inch steel 15/16 inch wide by 1-1/2 inches high by 48 inches long with factory punched cross tee slots, hanger holes, and staked-on stab-in end couplings.


3. Web Covers (optional:

a. Manufactured from 0.010 inch steel 2 inches high by 5/16 inches wide by 48 inches long, formed to a “U” Aluminum Steel shape, (with (without pre-punched hanger holes.


4. Wall Angle:

a. Manufactured from (0.020 inch steel (0.025 inch thick aluminum 3/4 inches wide by 15/16 inches high by 144 inches long with both edges hemmed.


C. Accessories:

1. Suspension Clips: Manufactured from steel with factory applied (white (black baked-on enamel paint finish.

2. Alignment Components: Manufactured from clear acrylic.


A. Examine area receiving system to identify conditions which will adversely affect installation. Do not begin installation until adverse conditions have been remedied.

B. Verify completion of work above ceiling plane prior to installation.

3.02 Installation

A. Suspension Components:

1. Main Tees: Installed 48 inches on center by direct suspension from existing structure, with not less than 12 gauge hanger wires wrapped tightly 3 full turns, spaced 48 inches on center along component length.

2. Web Covers: Installed on main tees during main tee installation.3. Cross Tees: Installed perpendicular to main tees 48 inches on center forming

48 x 48 inch modules.4. Wall Angles: Installed on vertical surfaces intersecting suspension system

by appropriate method in accordance with industry accepted practice.B. Linear Baffle Panels and Accessories:

1. Baffle Panels:

a. Installed perpendicular or diagonally to main tee component spaced as noted on project drawings, or identical to the baffle panel depth. 6 inch maximum allowable overhang for baffle panels.

b. Attached with suspension clips to main tees.

c. Connected with top alignment clip and bottom alignment sleeve.

3.03 Repair



Specification CubeGrid™ Open Plenum Grid


Modular suspended open plenum ceiling system.








1.03 References




1.04 Submittals


B. 12 inch long samples of Main Tees and Cross Tees with integral couplings.







1.06 Maintenance



Chicago Metallic C1811/C1802/C1804 double web Intermediate duty non-fire rated ceiling suspension system. Installed to form open plenum module size of (12 inches x 12 inches(24 inches x 24 inches(48 inches x 48 inches(___ x ___.


A. Main Tees:

1. C1811 - 144 inch long, manufactured from (0.015(0.020 inch steel 15/16 inch wide by 1-1/2 inches high with factory punched holes only where necessary to achieve tee intersections, hanger wire suspension and integral bayonet-style end couplings.

2. Finish: Web and end couplings - baked enamel paint (01 White(08 Black(44 Satin Silver Metallic(Other color ______. Cap - (matching baked enamel color [Anodized Face Only (14 Chromecoat(16 Brasscoat(509 Coppercoat], (WoodScenes painted color ______.

B. Cross Tees:

1. (C1802, 24 inch long (C1804, 48 inch long manufactured from 0.015 inch steel 15/16 inch wide by 1-1/2 inch high by with factory punched cross tee slots only where required to achieve grid intersections and integral bayonet-style end couplings.

2. Finish: Web and end couplings: baked enamel paint (01 White(08 Black(44 Satin Silver Metallic(Other color ______. Cap: (matching baked enamel color [Anodized Face Only (14 Chromecoat(16 Brasscoat(509 Coppercoat].

C. Perimeter Treatment Components:

1. Angle Moldings: (C3209.08, 1 inch wide x 2 inch high (38.90.124.xxx, 3/4 inch wide by 15/16 inch high 15/16 inch face by 144 inches long finished identical to main tees and cross tees.

2. Floating Perimeter Trim: Infinity™ by Chicago Metallic. Made from extruded aluminum [(2(4(6(8(10(12] inches deep. Painted on all sides [(to match CubeGrid(Other painted color _________].

3. Hanger wire: galvanized.

Specification GraphGrid™ Open Wire Ceiling Panel


Modular suspended open plenum ceiling system.








1.03 References




1.04 Submittals


B. Samples of panel with chosen cell size and suspension system including main tees and cross tee with integral end couplings.







1.06 Maintenance



Chicago Metallic GraphGrid™ panel and CubeGrid™ double web Intermediate duty non-fire rated ceiling suspension system. Installed to form open plenum module size of 24 inches x 24 inches.


A. Main Tees:

1. CubeGrid C1811, 144 inch long, manufactured from 0.015 inch thick steel 15/16 inch wide by 1-1/2 inches high with factory punched holes only where necessary to achieve tee intersections, hanger wire suspension and integral bayonet-style end couplings.

2. Finish: Web and end couplings - baked enamel paint (01 White(08 Black(44 Satin Silver Metallic(Other color ______. Cap - (matching baked enamel color [Anodized Face Only(14 Chromecoat(16 Brasscoat(509 Coppercoat].

B. Cross Tees:

1. CubeGrid (C1802, 24 inch long(C1804, 48 inch long manufactured from 0.015 inch thick steel 15/16 inch wide by 1-1/2 inch high with factory punched cross tee slots only where required to achieve grid intersections and integral bayonet-style end couplings. Cross tees to include bulb-forward design to minimize gap between cross tee and main tee.

2. Finish: Web and end couplings: baked enamel paint (01 White(08 Black(44 Satin Silver Metallic(Other color ______. Cap: (matching baked enamel color [Anodized Face Only(14 Chromecoat(16 Brasscoat(509 Coppercoat].

C. Perimeter Treatment Components:

1. CubeGrid Angle Moldings: (C3209, 1 inch wide x 2 inch high (38.90.124.xxx, 15/16 inch wide by 15/16 inch high 3/4 inch face by 144 inch long finished identical to main tees and cross tees.

2. Infinity™ perimeter trim: Made from extruded aluminum [(2(4(6(8(10(12] inches deep. Painted on all sides [(to match CubeGrid(GraphGrid(Other painted color _________].


BeamGrid™ Open Plenum Beam Specification

PART1-GENERAL1.01 Scope

Furnish and install the BeamGrid ceiling system as manufactured and supplied by Chicago Metallic Corporation.


A. Section 092000 - Plaster and Gypsum Board

B. Section 095100 - Acoustical Ceilings

C. Section 096300 - Acoustical Ceiling Suspension Assemblies

D. Section 095400 - Specialty Ceilings

E. Section 210000 - Fire Suspension

F. Section 220000 - Plumbing

G. Section 230000 - Heating, Ventilating and Air Conditioning

H. Section 265000 - Lighting

1.03 References


1. C 635 - Standard Specification for the manufacture, performance, and testing of Metal Suspension Systems for Acoustical Tile and Lay-in Panel Ceilings.

2. C 636 - Standard Practice for Installation of Metal Ceiling Suspension Systems for Acoustical Tile and Lay-in Panels.

1.04 Submittals



C. Shop Drawings: Reflected ceiling plan and elevation drawings indicating ceiling layouts, dimensions and perimeter conditions.










Chicago Metallic BeamGrid™ non-rated beam suspension system.

2.02 Beam suspension system components

Finish to be [(Painted with baked enamel finish (379 Gloss White (386 Gloss Black (color_____] [(Reflective anodized finish (14 Chromecoat (16 Brasscoat (378 Brushed Aluminum]. (WoodScenes painted finish _____.A. Main and cross beams:

1. Manufactured to a (1 in. x 1 in.(1 in. x 2 in.(1 in. x 4 in.(2 in. x 2 in.(2 in. x 4 in.(3 in. x 3 in.(4 in. x 4 in. channel shape from 0.024 in. aluminum.

2. Manufactured with factory pre-punched slots and holes properly spaced to provide module size: (12 in. x 12 in.(12 in. x 24 in.(16 in. x 16 in.(24 in. x 24 in.(24 in. x 48 in.(30 in. x 30 in.(36 in. x 36 in.(48 in. x 48 in..

B. Perimeter treatments:

1. Perimeter beam: Manufactured identical to main and cross beams with intersection slots on one side only at inside and outside 90° corners provide 90° corner kits with 45° miters.

2. Corner Kit: Manufactured to same profile as main beams from identical metal with 45° miter at appropriate end.

3. Wall channel: Manufactured from same material and finish as main and cross beams.[(Painted 360°(Reflective finish on outer surface only].

4. Wall channel-double: Manufactured from same material and finish as main and cross beams.

5. Curved perimeter trim (Infinity™: [(2 in.(4 in.] painted [(to match main and cross beams(color _____].

C. Suspension:

1. Hanger wire: galvanized.


Examine area receiving system to identify conditions which will adversely affect installation. Do not begin installation until adverse conditions have been remedied.

3.02 Installation

A. Affix hanger/couplers on appropriate centers, as recommended by Chicago Metallic, to main beam components. Suspend main beam components from 12 gauge hanger wire attached to the coupler. Main beams are to be installed on appropriate centers as dictated by module size and component layout. For continuous runs of the main beam components, splice the components together by pop-riveting the coupler to the consecutive main beam components.

B. Install cross beam components by inserting the attachment tabs located at each end of the component into the appropriate slot on the main beam components.

C. Complete the system by affixing main and cross beam components to the perimeter components. For free-floating applications, perimeter beam components shall be suspended from 12 gauge wire attached to hanger/couplers affixed to the component in an identical manner as described above for the main beam components. For applications requiring the BeamGrid system to be affixed to a wall or other structure establishing the perimeter of an installation, attach the perimeter beams to the structure, prior to installing main and cross beams, by means of an industry-accepted practice. For free-floating applications, attach the 90° corners, upon completion of field assembly, to appropriate components by means of the hanger/coupler.

3.03 Repair



Specification MetalScapes™ Wire Mesh Panel

PART1-GENERAL1.1RelatedDocumentsDrawings and general conditions of Contract, including General and Supplementary Conditions and Divisions-1 Specification sections apply to work of this section.

1.01SectionIncludesA. Open metal mesh ceiling panelsB. Metal acoustical ceiling suspension systems.C. Suspension system accessories and perimeter treatment.

ModularSuspendedOpenPlenumCeilingSystem.1.02RelatedSectionsA. Section 09 22 26 - Suspension SystemsB. Section 09 54 00 - Specialty CeilingsC. Section 13 42 00 - Building ModulesD. Section 13 48 00 - Sound, Vibration, and Seismic ControlE. Section 23 50 00 - Central Heating EquipmentF. Section 26 50 00 - Lighting

1.03ReferencesA. American Society for Testing and Materials (ASTM

1. A 641 Standard Specification for Zinc-Coated (Galvanized Carbon Steel Wire.

2. A 653 Standard Specification for Steel Sheet, Zinc-Coated (Galvanized by the Hot-Dip Process.

3. A 100B Standard Specification for Steel Sheet, Cold-Rolled, Carbon, Struc-tural, High-Strength Low-Alloy and High Strength Low-Alloy with improved Formability.

4. C 423 Sound Absorption and Sound Absorption Coefficients by the Rever-beration Room Method.

5. C 635 Standard Specification for the manufacture, performance, and testing of Metal Suspension Systems for Acoustical Tile and Lay-in Panel Ceilings.

6. C 636 Standard Practice for Installation of Metal Ceiling Suspension Sys-tems for Acoustical Tile and Lay-in Panels.

1.04SubmittalsA. Product data sheets listing dimensions, load carrying capacity and standards

compliance. B. Samples of panel with chosen cell size and suspension system including main

tees and cross tee with integral end couplings.

1.05ProjectConditionsA. Environmental Requirements:


2. Wet trades work to be thoroughly dry and complete prior to installation.3. Installation to begin only when temperature and humidity conditions closely

approximate interior conditions which will exist when area is complete and occupied.


5. The placement of wire mesh panels may affect the distribution of fire sup-pression systems by delaying or accelerating the distribution of sprinkler discharge toward or away from the source of heat. Designers and installers must consult a fire protection engineer, NFPA 13 or their local codes for guidance where automatic fire suppression systems are present.

1.06Delivery,StorageandHandlingA. Store the ceiling panels in cartons in a dry, interior location before installation to

avoid damage.B. Exercise care when handling and moving cartons and panels so as not to cause

damage.

1.06Maintenance Furnish additional material equal to ______ percent of ceiling area.

PART2-PRODUCTS2.01ManufacturersChicago Metallic – MetalScapes™ Wire Mesh PanelsChicago Metallic – Heavy-duty, hot dipped galvanized suspension, non-fire rated, double web construction system. System of main runners and cross tees to form module size of 24 inches x 24 inches or 24 inches x 48 inches in 15/16 inch (1200 system with exposed face.

2.02SuspensionSystemComponentsA. Main Tees:

1. Components are 144 inches long, manufactured from commercial quality galvanized steel with factory punched cross tee slots, hanger holes and hanger wire suspension of not less than 12 gauge, and integral end cou-plings.

2. Finish: Web and end couplings - baked enamel paint (01 White(08 Black(44 Satin Silver Metallic(Other color ______. Cap - (matching baked enamel color [Anodized Face Only(14 Chromecoat(16 Brasscoat(509 Coppercoat].

B. Cross Tees:1. Components are 48 inches and/or 24 inches long, manufactured from com-

mercial quality galvanized steel installed perpendicular to main runners with

integral bayonet-style end couplings to achieve grid intersections. Cross tees to include bulb-forward design to minimize gap between cross tee and main tee.

C. Perimeter Treatment Components. 1. Wall Channels: Wall channels are formed from 0.020 inch (electro-galva-

nized steel (aluminum and manufactured to a C-shape, with a 3/4 inch top leg by 1-9/16 inch I.D. and 15/16 inch bottom leg. Length is 144 inches. Finish shall be supplied by manufacturer.

2. Wall Angle: (C3209, 1 inch wide x 2 inch high and 120 inches long. (1430, 7/8 inch high x 144 inches long finished identical to main tees and cross tees.

3. Infinity™ Perimeter Trim: Made from extruded aluminum [(2(4(6(8(10(12] inch deep. Painted on all sides [(to match main and cross tees(Other painted color _________].

D. Panels. 1. MetalScapes wire mesh panels (stainless steel, made from .031 min to

.162 wire diameter T316 stainless steel to form panels for 24 inch x 24 inch or 24 inch x 48 inch ceiling modules. MetalScapes wire mesh panels (carbon steel made from .040 min to .765 Cold-Rolled Steel Grade DDS to form panels for 24 inch x 24 inch or 24 inch x 48 inch ceiling modules.

2. Finish: Will be baked enamel paint on all sides (01 White (08 Black (44 Satin Silver or (Other color _____.Carbon steel panels only.

E. Hanger Wire. 1. Hanger wire: 12 gauge galvanized steel.

PART3—EXECUTION3.01ExaminationExamine area receiving suspension system to identify conditions which will adversely affect installation. Do not begin installation until adverse conditions have been remedied.

3.02InstallationA. Main Tees: Installed 48 inches on center, by direct suspension from existing

structure, with not less than 12 gauge steel hanger wires, wrapped tightly 3 full turns, spaced 48 inches on center along component length.

B. Cross Tees. 1. Installed perpendicular to main tees 24 inches on center to form 24 inch x

24 inch modules. 2. Installed perpendicular to module 48 inches on center to form 24 inch x 24

inch modules or 24 inch by 48 inch modules.C. Angle / Moldings: Installed on vertical surfaces, intersecting suspension compo-

nents by appropriate method in accordance with industry accepted practice.D. Additional Hanger Wires: Wrapped tightly 3 full turns to structure and compo-

nents at locations where imposed loads could cause deflection exceeding 1/360 span.

E. Panel: Lay panels into ceiling module. Panels are directional with wires on panel faces to be in same direction.

3.03RepairA. Remove damaged components, replace with undamaged components. Clean

with non-solvent based non-abrasive commercial cleaning solution.

Panel Size (Nominal) Color Pattern Wire DiameterLbs. Per Sq. Ft.

Open Area %

24" x 24", 24" x 48" Stainless steel Appalachian .162" 1.21 89%

24" x 24", 24" x 48" Stainless steel Alps 0.062" 1.23 52%

24" x 24", 24" x 48" Stainless steel Everest 0.093" x 0.031" 1.20 79%

24" x 24", 24" x 48" Stainless steel Rockies 0.080" x 0.054" 1.09 52%

24" x 24", 24" x 48" Stainless steel Hood 0.080" x 0.047" 1.11 57%

24" x 24", 24" x 48" Stainless steel Atlas 0.080" x 0.080" 1.35 51%

24" x 24", 24" x 48" Stainless steel Ural 0.162" x 0.162" 1.78 66%

24" x 24", 24" x 48" Stainless steel Tyber .120" 1.90 27%

24" x 24", 24" x 48" Carbon steel Aberdeen 0.04" 0.56 44%

24" x 24", 24" x 48" Carbon steel Erlanger 0.048" 0.50 62%

24" x 24", 24" x 48" Carbon steel Frankfort 0.08" 0.38 70%

24" x 24", 24" x 48" Carbon steel Scales 0.082" 0.38 70%

24" x 24", 24" x 48" Carbon steel Armor 0.365" 1.00 21%

24" x 24", 24" x 48" Carbon steel Lattice 0.08" 0.63 50%


General Conditions of Sale

OrderAcceptanceWhenever used herein, “Seller” shall refer to Chicago Metallic Corporation and “Purchaser” shall refer to the party ordering or purchasing products (“Products” from Seller.

Seller’s price list does not constitute an offer to sell Products listed therein, but is simply provided as a convenience to prospective Purchasers.

Purchaser’s order to Seller shall constitute an offer to Seller to purchase Products which offer Seller may accept at its sole discretion. Acceptance shall be by a writing containing these General Conditions of Sale (“Conditions”. Acceptance of Purchaser’s order or any part of it by Seller is expressly made conditional on Purchaser’s assent to these Conditions. Purchaser may vary these Conditions only with the written consent of Seller. Acceptance of Products by Purchaser or failure of Purchaser to object in writing to these Conditions within ten (10 days following delivery of Products to Purchaser shall constitute Purchaser’s assent to these Conditions.

ShipmentandDeliverySeller shall deliver Product F.O.B. place of shipment. Risk of loss to Product shall pass to Purchaser upon delivery to carrier at such place of shipment. Carrier acts as Purchaser’s agent. Products shall be shipped as soon as practical, or as requested by Purchaser after order acceptance by Seller. However, delivery dates shall not be of the essence, but shall be regarded as Seller’s best approximation of such delivery dates.

PricesofFreightCostsUnless otherwise indicated, prices shown on Seller’s price list are for less than truckload quantities. The minimum truckload quantity is 24,000 pounds. Prices are subject to change without notice and are based on full carton quantities. Prices shall be those in effect at time of shipment of Products.

Seller shall grant Purchaser a freight allowance on all orders of 12,000 pounds or more for a single shipment to a single destination. The allowance shall be based on the lowest rates currently in effect from actual shipping point to destination point or nearest port of export. In no event shall the allowance be greater than the actual freight cost of a specific shipment. Purchaser’s request for costlier means of shipment will be honored, but Purchaser shall be liable to Seller for the additional freight expense. Purchaser “will-call” orders at Seller’s plant warehouse shall not be entitled to allowance.

All taxes, tariffs, duties or similar charges paid by Seller imposed or levied by any governmental authority in connection with the purchase, shipment, import or export of Products purchased or in connection with the procuring of materials used therein may at Seller’s sole option be added to the price of Products so affected. Additional shipping charges for Products paid by Seller such as destination, storage, labor and redelivery and special or extra expenses for handling air freight, bus or other shipments may also, at Seller’s sole option, be added to the price of such Products.

PaymentPayment for all Products shall be net cash due and payable in U.S. dollars within thirty (30 days following receipt by Purchaser of shipping documents for such Products by check or bank transfer to a bank account to be designated by Seller. If accounts are paid within ten (10 days following receipt by Purchaser of the corresponding shipping documents, Purchaser shall been entitled to a one percent (1% discount from the price of Products only.

If, in Seller’s sole opinion, the financial condition of the Purchaser so warrants, Seller may require advance payments or satisfactory security. In the event that the Pur-chaser fails to make such advance payments or furnish such security upon Seller’s request, delivery of Products may be suspended without further Seller obligation.

Seller may, at Seller’s sole option, require payment by means of an irrevocable letter of credit opened and confirmed by a bank or banks acceptable to Seller and upon terms and conditions acceptable to Seller.

LimitedWarrantySeller warrants to Purchaser that Products will substantially conform in quantity and quality to Purchaser’s order, as accepted by Seller, provided, however, that (1 Products are inspected by Purchaser upon arrival at place of destination and any and all nonconformities are noted on the bill of lading and all other delivery documents and are attested to in writing by carrier’s representative (2 Purchaser furnishes Seller with written notice of such non-conformities within fifteen (15 days following arrival of non-conforming Products at the place of destination, (3 Purchaser holds non conforming Products for Seller’s inspection (4 non-conformities occurred prior

to delivery by Seller of Products F.O.B. place of shipment, and (5 Purchaser does not alter, repair, use or attempt to alter or repair any non-conforming Products. This limited warranty is Seller’s only and exclusive express warranty to Purchaser. Seller disclaims any and all implied warranties including without limitation any implied warranty of merchantability or fitness for a particular purpose.

Purchaser’s sole and exclusive remedy against Seller shall be the replacement F.O.B. its plant or site, at Seller’s option, of any Products which do not conform to Seller’s limited warranty hereunder. No other remedy (including, without limita tion, incidental or consequential damages for lost profits, lost sales, injury to persons or property or any other incidental or consequential loss shall be available to Purchaser.

Purchaser agrees to include in all contracts between Purchaser and subsequent owners or users of Products, and to bring to the attention of all Purchaser’s custom-ers of Products, the following warranty disclaimer: Chicago Metallic Corporation disclaims any and all warranties expressed or implied, including, without limitation, any implied warranty of merchantability or fitness for a particular purpose. Purchaser shall be excluded on behalf of Seller all remedies for damage or injury to Products persons or property. In the event that Purchaser fails to comply with the foregoing obligations, Purchaser shall indemnify Seller for any liability resulting from such non-compliance and shall otherwise hold Seller harmless.

ReturnsIn order to return any Products to Seller, Purchaser must first obtain prior authorization for products eligible for return, and receive a Return Goods Authorization number from Seller’s home office. All authorized returns are subject to a 20% restocking charge. Seller will only issue credit for Service Level “0” material received at the designated company facility with the Return Goods Authorization appearing on the material, and after being inspected and determined by Seller to be in resalable condition. Purchaser is solely responsible for arranging and prepaying for all return freight. Seller will not be responsible for any damage in transit on material returned at customer’s request, and will not file freight claims on such damaged material. When these terms are met, seller will issue appropriate material credit less the restocking charge.

Default,TerminationandSuspensionofDeliverySeller reserves the right, among other remedies, either to cancel Purchaser’s order or suspend further deliveries of Products thereunder in the event that (1 Purchaser fails to pay for any one shipment of Products when payment for such shipment becomes due; (2 Purchaser fails to make any advance payments or satisfactory security demanded by Seller pursuant to paragraph two of PAYMENTS section above; or (3 Purchaser fails or refuses to accept any delivery of Products ordered from Seller.

Delivery of Products may be suspended in whole or in part in case of any event beyond Seller’s control, including, but not limited to, explosion, fire, shortage of fuel, power or raw materials flood strike lockout, injunction, riot, insurrection, war, national emergency, government act, or act of God.

MiscellaneousNo failure or delay on the part of Seller in exercising any right, power or privilege hereunder shall operate as a waiver thereof or of any other right, power or privilege hereunder nor shall any single or partial exercise of any such right power or privi-lege preclude any other right, power or privilege. The rights or remedies of Seller hereunder are cumulative and not exclusive of any rights or remedies which it may otherwise have.

The parties hereto may correct stenographic and clerical errors without liability.

Purchaser may not assign the order without the express written consent of Seller.

All notices to be given hereunder by either party to the other party shall be dispatched by certified or registered mail return receipt requested addressed to the last known post office address of such other party. Any such notice shall be deemed received within five (5 days following any such dispatch if mailed from within the United States of America and ten (10 days if mailed from outside the United States of America. Either party may change its address by notice to the other party.

These Conditions shall be governed by and interpreted in accordance with the laws of the State of Illinois, United States of America, and all disputes hereunder that cannot be amicably resolved by the parties thereto must be settled in a court of competent jurisdiction within the State of Illinois, United States of America.

The provisions of these Conditions shall be severable one from the other so that should any provision be held legally unenforceable by a court of competent jurisdic-tion, the remaining provisions shall remain in effect.

LiteratureDisclaimer:Presentations in this brochure or any other Chicago Metallic Corporation publication are correct to the best of our knowledge at time of preparation. We provide this information in an advisory capacity only. Any advisory recommendations given in our publications mustbemodifiedtoconformwithlocalcodes, conditions and specifications. We reserve all rights to amend any information published in our literature without additional notice. Chicago Metallic can not be held responsible or liable for the selection nor application of our products.

Ceiling Systems and Specialty Products - USA and Canada: 800.323.7164 / Fax: 800.222.3744 / chicagometallic.combelgium / denmark / the netherlands / uk / germany / france / hong kong / china / malaysia / united arab emirates / mexico

Chicago Metallic, its logo, Fast.Easy.Customer Focused., SpanFast and QuickClick are Registered Trademarks of Chicago Metallic Corporation. Snap-Grid, Tempra and Ultraline are trademarks of Chicago Metallic Corporation.© 2011 Chicago Metallic Corporation All Rights Reserved Printed in USA SNL0105L1311

linear metal

ceiling09 53 23 - 09 54 26Planar ®

PlanarPlus ® PlanarMacro® MacroPlus™

product guide


2 Planar Linear Metal Ceiling chicagometallic.com3 Planar Linear Metal Ceiling chicagometallic.com

Always up-to-date product information is available on the web

chicagometallic.com/planar chicagometallic.com/planarplus

chicagometallic.com/planarmacro chicagometallic.com/macroplus


UPDATES

ApplicationsIdeal for airports, transit, galleries, offices, restaurants, corridors, auditoriums.

Features• Choice of widths, round and square edges, shallow

and deep profiles.

• Thickness and finishes for virtually any environment.

• Painted colors, reflective, anodized and vinyl wood finishes.

• Reveals between panels can be closed or left open.

• Easily incorporates lighting, air, audio and services.

• Visual design continuity from exterior to interior.

• Enhance acoustical performance with optional perforating and Acoutex™ backer.

• Metal contains no organic compounds to support mold or microbial growth.

• Aluminum: 100% recycled content; Steel: T-bar Carrier is 25% recycled content. 100% locally recyclable.

Planar ®

PlanarPlus® PlanarMacro®

MacroPlus™

linear metal ceilings

Recessed Filler Strip

4 Planar Round Edge – Open Reveal

PlanarPlus Panelwith Integral Filler

Recessed Filler Strip

PlanarMacro Panel

MacroPlus*- Panelwith Integral Filler

Symmetrical Carrier(grid available)

4 PlanarPlus Square Edge with Integral Filler

Planar Panel

6 PlanarMacro Square Edge – Open Reveal

8 MacroPlus Square Edge with Integral Filler




2 Planar Linear Metal Ceiling chicagometallic.com3 Planar Linear Metal Ceiling chicagometallic.com USA and Canada: 800.323.7164 / fax: 800.222.3744 Planar Linear Metal Ceiling 3

Planar® PlanarPlus® 4 Round / Square Edge Panels

Product Dimensions Packaging Number Length Height Face Finish Feet Pieces Weight

4 Planar Round Edge – Open Reveal*0.025 Aluminum – Solid

Painted, Reflective, Anodized

58.01.044.xxx 12 5/8 31/4 MetalWood II®, WoodScenes™ 240 20 40

* AvailableperforatedwithAcoutex™backer.

4 PlanarPlus Round Edge – Matching Integral Filler*0.025 Aluminum – Solid




4 Planar Square Edge – Open Reveal*0.025 Aluminum – Solid



* AvailableperforatedwithAcoutex™backer.** Unfinished(xxxU)orFinished(xxxF).NaturalWood(unperfedonly).

4 PlanarPlus Square Edge – Matching Integral Filler*0.025 Aluminum – Solid

Painted, Reflective, Anodized 58.03.018.xxx 12 5/8 31/4 MetalWood II®, WoodScenes™

240 20 44


4 Planar Round Edge58.01.044

4 PlanarPlus Round Edge58.03.012

4 Planar Square Edge58.03.052

4 PlanarPlus Square Edge58.03.018

NOTE: Special panel lengths are available. Minimum order quantities apply to all products. Please contact CMC Customer Service for details.

5/8

4

5/8

4

5/8

4

5/8

4


PlanarMacro® 4, 6 and 8 Square Edge Panels


4 PlanarMacro Square Edge – Open Reveal*0.032 Aluminum – Solid




6 PlanarMacro Square Edge – Open Reveal*0.032 Aluminum – Solid**



* AvailableperforatedwithAcoutex™backer.** MetalWoodIIFinishesarelaminatedonto0.024aluminum.

8 PlanarMacro Square Edge – Open Reveal*0.032 Aluminum – Solid




4 PlanarMacro Square Edge58.03.425

6 PlanarMacro58.03.450

8 PlanarMacro58.03.455


7/8

4, 6, 8


MacroPlus™ 4, 6 and 8 Square Edge Panels


4 MacroPlus Square Edge – Matching Integral Filler*0.032 Aluminum – Solid







* AvailableperforatedwithAcoutex™backer.** MetalWoodIIFinishesarelaminatedonto0.024aluminum.6MacroPlusSquareEdge–MatchingIntegralFiller





4 MacroPlus58.03.426




7/8

4, 6, 8


Filler Strips / Splices / End Plugs Product Dimensions Packaging Number Length Height Face Finish Feet Pieces Weight

Filler Strips – Aluminum (for Planar / PlanarMacro)Recessed

Painted Colors, MetalWood II®,

58.01.009.xxx 12 – 3/4 WoodScenes™, Reflective, Anodized 240 20 15

Recessed for Expansion Carrier Painted Colors, MetalWood II®,

58.01.011.xxx 12 – 3/4 WoodScenes™, Reflective, Anodized

240 20 21

Splices - Aluminum4 Planar/PlanarPlus – Round Edge / Square Edge

Painted Colors, MetalWood II®, 58.01.004.xxx – – 31/4 WoodScenes™, Reflective, Anodized – 50 4

4 PlanarMacro/MacroPlus Painted Colors, MetalWood II®, 58.03.525.xxx – – 31/4

WoodScenes™, Reflective, Anodized – 50 5

6 Planar/PlanarPlus Painted Colors, MetalWood II®, 58.03.530.xxx – – 51/4


8 Planar/PlanarPlus Painted Colors, MetalWood II®, 58.03.535.xxx – – 71/4


Recessed Filler Strip58.01.009 - 58.01.011

Splice58.01.004-58.03.525 58.03.530-58.03.535

NOTE: Minimum order quantities apply to all products.

ProductNumber

Dimensions

Description

MinimumOrderQuantity

Height Face Pieces Weight

End Plugs – Aluminum

4˝ Planar/PlanarPlus – Round Edge58.01.052.xxx 5/8˝ 3 1/4˝ Standard Colors 100 158.01.052.xxx 5/8˝ 3 1/4˝ Premium Colors and Finishes 100 158.01.052.xxx 5/8˝ 3 1/4˝ WoodScenes 100 1

4˝ Planar/PlanarPlus – Square Edge58.03.171.xxx 5/8˝ 3 1/4˝ Standard Colors 100 158.03.171.xxx 5/8˝ 3 1/4˝ Premium Colors and Finishes 100 158.03.171.xxx 5/8˝ 3 1/4˝ WoodScenes 100 1

4˝ PlanarMacro/MacroPlus – Square Edge58.03.625.xxx 7/8˝ 3 1/4˝ Standard Colors 100 158.03.625.xxx 7/8˝ 3 1/4˝ Premium Colors and Finishes 100 158.03.625.xxx 7/8˝ 3 1/4˝ WoodScenes 100 1



End Plug Round Edge58.01.052

End Plug Square Edge58.01.171, 58.03.625, 58.03.630, 58.03.635


Planar® PlanarPlus® PlanarMacro® MacroPlus™ Suspension

Product Packaging Number Length Description Feet Pieces Weight

SuspensionCarriers

58.01.007.008 12 Symmetrical Carrier – Aluminum* 240 20 47 Per Order 12 Radius Symmetrical Carrier – factory curved** 240 20 47 58.01.022.008 12 Expansion Carrier – 41/8 for 4 and 8 Panels 240 20 47 1500.08C 12 T-Bar Carrier for 4 and 8 Panels – Steel 144 12 23 1501.08C 12 T-Bar Carrier for 6 Panels – Steel 144 12 23 58.01.008.008 10 Radius Carrier – 2 for 6 Panels 200 20 40 58.01.005.008 10 Radius Carrier – 4 for 4 and 8 Panels 200 20 40*Symmetricalcarrierisrequiredonallexteriorapplications.**Forradiussymmetricalcarrierspecifyradiusattimeoforder.Curvingavailableconcaveonly.

Accessories 58.01.403.008 – Symmetrical Carrier Splice – 100 4 58.01.028.008 4913/16 Interior Stabilizer Bar for Symmetrical Carrier – 50 17 58.01.029.008 3513/16* Exterior Stabilizer Bar - Symmetrical Carrier – 50 12 1503.08H 4 Cross Tee for T-Bar Carrier 200 50 38 10.00.828.000H 4 Spacer Bar for T-bar Carrier 160 40 29 58.01.318.000 – Retainer Clip - Separate filler used – 500 4 58.01.317.000 – Retainer Clip - Integral filler used – 500 4

Access Door Assembly Kit 58.01.058 (2 Hinge Assemblies, 4 Retainer Clips, 2 Retainer Bars) – – 1

*2StabilizerBaravailableasaspecial.PleasecontactCMCCustomerService.

Symmetrical Carrier58.01.007

Expansion Carrier58.01.022

T-Bar Carrier1500.08C-1501.08C

Radius Carrier58.01.008-58.01.005

Splice58.01.403

Stabilizer Bar58.01.028 - 58.01.029

Cross Tee1503.08H

Spacer Bar10.00.828.000

Retainer Clip58.01.318 - 58.01.317



For INTERIOR Use Only

StationaryCarrier

HingeAttachwith(2)3/16poprivets

NotchFillerFlange Forclearance

BoltandNut 3/16x1-1/4

RetainerClip(Attachwith3/16poprivetsusingexistingCarrierholes)

RecessedFillerStrips(Flattenendsandcentersforfastening)Attachwithself-tappingscrews

Self-tappingScrew

LeaveroomatendsofCarrierforhinges,latchclipsorlatchbars

AccessDoorCarrier

StationaryCarrier

LatchingBar(DrillbarholestomatchCarrierholes.Attachwith(2)3/16poprivets)

Linear Metal Panel Access Door Treatment - Interior / Exterior

Drill3/4diameteraccessholeinPlanarMacroPluspanel

TrimPlanarMacroPluspanel&Planarcarrierasrequiredforclearance

Secureaccessdoortostopbarwith1/4-20x1lg.hexwasherheadscrew(by others).

DETAILAStabilizerBar@36 orlessO.C.spacing

#10self-tapscrew(by others)18ga.tiewire(by others)

12ga.electrogalvanizedhangerwire(by others) Strut and attachment to deck

(by others)

11/2widex9/16flangex20ga.coldrolledsteelchannelstabilizer-bothsidesofopening(by others)

Hinge(attachwith(2)3/16poprivets)

Notchfillerflangeforclearance

3/16x11/4bolt&nutAccessDoorCarrier

Useself-tappingscrews.Fasten4fromedgetoaccomodatelatchparts(by others)

11/2widex9/16flangex20ga.steelchannelstiffener-flattenonechannelincenterforfastening(by others)

StationaryCarrier

#58.01.056.900StopBar(2places)-attachwith(2)1/4-20machinescrews&(2)1/4-20hexnuts(by others)seeDETAILA

NOTE: Exterior soffit design and engineering is Contractors responsibility. Consult with an Engineer to evaluate the suitability of the system for the intended application.

AccessDoorCarrier#58.01.056.900StopBar

StationaryCarrier

For EXTERIOR Use Only


Linear Metal Panel Curved Treatment - Factory / Field

FACTORY Planar Symmetrical Carrier for CONCAVE TreatmentsNote: Factory curved carriers are not available for convex applications

FIELD Modified Planar Symmetrical Carrier for CONVEX Treatments

of 4 Planar OnlyShown using 4 Planar Round Edge Panels

Contact CMC Tech Services for instructions using other panel options

FIELD Modified Planar Symmetrical Carrier for CONCAVE Treatments

of 4 Planar OnlyShown using 4 Planar Round Edge Panels

Contact CMC Tech Services for instructions using other panel options

VerticalSlot

Planarpan

VerticalSlot

Planarcarrier

12minimumradius

Cutout"Vee"sections,downtohorizontalshoulderofcarrier

Do Not Cut Carrierinareaabovetabsthatholdpanels

Formcarrierandfillerstriptodesiredshapeandscrewattach,orpop-rivet,fillerstriptocarrieronbothsidesofcut

4Planarroundedgepan

Tek-screworpoprivet

FillerStrip

SymmetricalCarrier

Section A-A

Sawcut,downtohorizontalshoulderofcarrierbetweentabswithoutstabilizerslots

Do Not Cut Carrierinareaabovetabsthatholdpanels

Formcarrierandfillerstriptodesiredshapeandscrewattach,orpop-rivet,fillerstriptocarrieronbothsidesofcut

4Planarroundedgepan

Tek-screworpoprivet

FillerStrip

SymmetricalCarrier

Section A-A


Product Dimensions Packaging Number Length Height Face Description LF Pieces Weight

Wall Angles – Aluminum with Hemmed Edges

38.90.124.xxx 12 3/4 15/16 Painted, Reflective, MetalWood II® 120 10 10

Wall Channels – Planar – Aluminum with a Hemmed Edge 58.03.017.xxx 10 113/16 17/8 x 1 Anodized, MetalWood II® 100 10 14

Wall Channels – PlanarMacro – Aluminum with a Hemmed Edge 58.03.717.xxx 10 2 15/8 x 1 Anodized, MetalWood II® 100 10 14

Custom Trims (PVC) 38.35.995.000 10 2 1/2 Flexible Angle-Aluminum-Bare 100 10 10 38.90.131.xxx Per Order Special Sections – – –

Planar® PlanarMacro® Perimeter Treatments & Accessories

Wall Angles38.90.124

Wall Channels 58.03.017 - 58.03.717

Custom Trims38.35.995.000 38.90.131

Product Roll Roll Sq.Ft. Packaging Number Size Width Description PerRoll Pieces Weight

Acoustical Blanket – Vinyl Facing One Side

58.01.103.008 100 48 1 x 1 lb. - Black 400 1 56 58.01.060.008 100 48 1 x 11/2 lb. - Black 400 1 76 58.01.104.008 100 48 11/2 x 1 lb. - Black 400 1 58 58.01.102.008 100 48 11/2 x 11/2 lb. - Black 400 1 78

Duct Liner – Black with No Facing 58.01.105.008 100 48 1 x 11/2 lb. 400 1 76

Note: Please consult CMC Customer Service for Panel Cutting Tool and pricing.



2-Slot Diffuser58.01.072




Product Packaging Number Description Pieces Weight

Air Diffusers

58.01.072 2 slot unit, 8 collar, 9 width 1 10 58.01.074 4 slot unit, 10 collar, 17 width 1 13 58.01.076 6 slot unit, 12 collar, 25 width 1 16 58.01.078 8 slot unit, 14 collar, 33 width 1 20 58.01.108 Round Edge Planar Pattern Control 1 1 58.01.107 Macro and Square Edge Planar Pattern Control 1 1Notes: Numberofslotsbasedon4panels. Onepatterncontrolisneededforeachslotopeningonairsupplyunits. Standardcollarsaretopmounted.Oval,sideinletcollarsarespecialorder. AirdiffusersarecompatiblewithSymmetricalCarrieronly.

Planar® PlanarMacro® Air Distribution

Air diffusers are designed to install as tailored components to the Planar Linear Metal Ceiling System. Dimensions of the Affinitrol Air Diffuser are compatible with ceiling panels and carriers. The Affinitrol air chamber spans the 50” area between carriers.

Planar PlanarMacro



Perimeter Treatments***

System Treatments

T Pattern

0.0625diameterholes0.216linealcenters.125border7.6%openarea

Perforation Option

Color Options

Wall angle - recessed

Wall angle - flush

Wall channel

Wall channel - floating

End cap

Infinity™ perimeter trim

Standard Painted Colors 01 White 02 Black 44 Satin Silver

Premium Painted Colors 03 Bronze 21 Copper Metallic 23 Sandstone 88 Flat Black 113 Straw 167 Brick Red 174 Garnet 215 Forest Green 246 Federal Indigo 256 True Blue 263 Plum 270 Pearl Gray 379 Gloss White 386 Gloss Black 401 Maple* 402 Oak* 403 Cherry* 404 Pumpkin Maple* 405 Karri* 425 Wet Clay 428 Yellow Flash 429 Silver Lining 430 Beige Breeze 431 Whitewash 432 Blonde Wood 437 Midnight Blue 438 Royal Amethyst 442 Burgundy Brick 443 Toffee Fate 447 Cinnamon 449 Fortune Gray 455 Cocoa Shell 495 Cardinal Red 510 Morning Dew Metallic

511 Autumn Metallic 512 Moon Glow Metallic 513 Sun Gold Metallic515 Sterling Metallic 516 Flint Metallic 517 Emerald Metallic 520 Polar White 521 Nickel 524 Silver

WoodScenes™ Painted Colors 800 Lazy Maple 801 Aged Teak 802 Vintage Burlwood 803 Burnished Cherry 804 Sleek Cherry 805 Weathered Oak

Reflective Finishes 369 Brushed Gold** 378 Brushed Aluminum**

Anodized Finishes 14 Chromecoat Anodized 16 Brasscoat Anodized 504 Satin Silver Anodized 509 Copper Coat Anodized

MetalWood II® Finishes* 401 Maple 402 Oak 403 Cherry 404 Pumpkin Maple 405 Karri 650R Maple 651R Cherry 652R Pumpkin Maple 653R Oak 654R Karri 655R Bamboo

*** Reference Wall Angles and Channels on p. 10. See Infinity Product Guide for other trim options.

* Coordinating Solid Paint Colors to MetalWood II® Finishes** 4" Planar Only


Specification DataProduct information for integration into ceiling specification

panel type Planar PlanarPlus PlanarMacro MacroPlus

material paintedaluminum • • • •

reflectiveandanodizedaluminum • • • •

Woodlaminatesonly • •

MetalWoodII®woodgrainfinishesandvinyllaminate • • • •

WoodScenes™paintedcolors • • • •

surface solidandperforated1 • • • •

size nominalpanelwidthxdepth 4x5/8 4x5/8 4,6,8x7/8 4,6,8x7/8

edge square • • • •

round • •

reveal openwithoptionalfillerstrip • •

integralfillerstrip • •

fire classA:flame0,smoke0 perASTME841 • • • •

sound NRC-solidwithopenreveal 0.602 0.602

NRC-perforatedwithopenreveal 0.553,0.952 0.553,0.952

NRC-perforatedwithclosedreveal 0.703,0.952 0.703,0.952 0.703,0.952 0.703,0.952

performance interior,seismicandexteriorenvironments4 • • • •

suspension aluminumsymmetricalcarrier(straightandcurved) • •

steelgridcarrier • • • •

aluminumradiuscarrier • •

lights and air linearintegratedlightingandairdiffusers • • • •

classification typeXX,patternC,GperASTME1264 • • • •

warranty 1yearlimited • • • •

sustainability Aluminum:100%recycledcontent;Steel:T-BarCarrieris • • • • 25%recycledcontent.100%locallyrecyclable. 1-Excludinglaminated. 2-With1-1/2,1-1/2lb.acousticalblanket 3-PerforatedwithAcoutex™backer 4-Consultwithanengineertoevaluatethesuitabilityofthesystemfortheintendedapplication.


Planar® PlanarPlus® Specification Data

PART1-GENERAL1.01Scope

ProvideLinearMetalCeilingSystem.1.02RelatedSectionsA. Section095100-AcousticalCeilingsB. Section096300-AcousticalCeilingSuspensionC. Section095400-SpecialtyCeilingsD. Section210000-FireSuspensionE. Section220000-PlumbingF. Section230000-HVACG. Section265000-Lighting1.03ReferencesA. AmericanSocietyforTestingandMaterials(ASTM)

1. C423-TestMethodforSoundAbsorptionandSoundAbsorptionCoefficientsbytheReverberationRoomMethod.

2. C635-StandardSpecificationforthemanufacture,performance,andtestingofMetalSuspensionSystemsforAcousticalTileandLay-inPanelCeilings.

3. C636-StandardPracticeforInstallationofMetalCeilingSuspensionSystemsforAcousticalTileandLay-inPanels.

4. E84-TestMethodforSurfaceBurningCharacteristicsofBuildingMaterials.5. E580-PracticeforApplicationofCeilingSuspensionSystemsforAcousticalTile

andLay-InPanelsinAreasRequiringSeismicRestraint.6. E795-PracticesforMountingTestSpecimensDuringSoundAbsorptionTests.1.04Submittals

A. Productdata:Manufacturersstandarddatasheetslistingdimensionsanddetails.B. Samples:Manufacturersstandardsamplesincludingsuspension,panelsandcolors.C. ShopDrawings:Reflectedceilingplanandelevationdrawingsindicatingceilinglayouts,

dimensionsandperimeterconditions.1.05ProjectConditionsA. EnvironmentalRequirements:

1. Verifyweathertightnesspriortoinstallation.2. Wet tradeswork tobethoroughlydryandcompleteprior tosuspensionsystem

installation.3. Installation tobeginonlywhen temperatureandhumidityconditionscloselyap-

proximateinteriorconditionstoexistwhenareaisoccupied.4. Heatingandair conditioningsystems tobeoperatingprior to,during,andafter

installation.5. Delivermaterialsinmanufacturersoriginalpackaging,unopenedandundamaged.6. Storematerialsinanencloseddrylocationatroomtemperatureandprotectfrom

soiling,damage,moistureandhumidity.1.06MaintenanceFurnishextramaterialequalto____percentofceilingarea.

PART2-PRODUCTS2.01Manufacturer

(Planar)(PlanarPlus)linearmetalceilingsystemsasmanufacturedbyChicagoMetallic,4849SouthAustinAvenue,Chicago,Illinois60638.1-800-323-7164.2.02MaterialsA. LinearMetalPanels:

1. Manufacturedfrom(0.025)inchthickaluminumnominal4incheswideby(144)(__)incheslongby5/8inchdeep.

a.Planarwith(round)(square)edges. b.PlanarPluswith(round)(square)edgesandintegralfillerstrips.

2. Finish:(Painted_____)(Reflective_____)(Anodized_____)(MetalWood®laminatedvinyl_____)(WoodScenes™Painted_____).

3. [(Unperforated)(PerforatedwithpatternT)] [(with)(without)]Acoutex™non-wovenmembranefactorybondedtopanelbackside.

B. Accessories1. PlanarRecessedFillerStrips:Manufacturedfromaluminum3/4inchwideby144

incheslongcoatedto(matchpanel)(_____color)withlinearmetalpanels.

2. PanelSplices:Manufacturedfrom0.025inchthickaluminum83/4incheslongcoatedwith(blackbaked-onpolyesterenamel)(finishidenticaltolinearmetalpanels),withprofilecompatiblewithlinearpanels.

3. EndPlugs:Manufacturedfrom0.025inchthickaluminumwith(round)(square)edges.Coatedidenticaltolinearmetalpanels.

4. PerimeterTrim a. PerimeterCaps:Manufacturedfrom0.025inchthickaluminum113/16inchI.D.

by17/8inchtopflangeby1inchbottomflangeby120incheslong.Coatedidentical

tolinearmetalpanels. b. WallAngles:Manufacturedfrom0.025inchthickaluminum15/16inchwideby3/4

inchhighby144incheslongwithhemmededges.Coatedidenticaltolinearmetalpanels.

C.SuspensionSystem1. SymmetricalCarrier: a. Manufacturedtoaninverted“U”shapefrom0.040inchaluminum144inches

long.Coatedwithblackpolyesterenamel. ArchitectNote:Doublegripcarrierrequiredonallexteriorapplications. b. Slottedatappropriateintervalstoreceivestabilizingcomponentsasdescribed

below.2. StabilizerBars:Manufacturedfrom0.040inchthickaluminum(4913/16)(3513/16)inch

long.Coatedwithblackpolyesterenamel.3. RadiusCarrier:Manufacturedtoaninverted“U”shapefrom0.040inchthickaluminum

120incheslongwithintegralcarriertabs,paintedblack.4. ExpansionCarrier:Manufactured toan inverted “U” shape from0.040 inch thick

aluminum144incheslongwithintegralcarriertabsspaced41/8inches.Coatedwithblackpolyesterenamel.

D.AcousticalMaterial1. Blankettypeblackvinylfacedoneside(1)(11/2)inchesthickby(1)(11/2)poundsper

cubicfootdensity.2. Blackmatteductliner1inchthickby11/2poundspercubicfoot.3. Acoutex™non-wovenfiberfactoryadheredtobackofperforatedpanels.

E.AirDiffusion1. AirUnits: a. (2)(4)(6)(8)slotwith(8)(10)(12)(14)incheswide(dampered)(undampered)top

mountedcollars. b. Manufacturedfrom0.024inchthicksteelwithgasketedlowerflangesandfactory

appliedacousticalinsulationadheredtointernalsurfaces. c. “L”shapeddirectionalvanespaintedblack. d. Optionalremotecontroldamperassemblywithcontrolcableextendingthrough

airdistributionslot.

PART3-EXECUTION3.01ExaminationExamineareareceivingsystemtoidentifyconditionswhichwilladverselyaffectinstallation.Donotbegininstallationuntiladverseconditionshavebeenremedied.3.02Installation(InteriorOnly)

A. SuspensionSystem1. SymmetricalCarriers:Installed50inchesoncenterbydirectsuspensionfromexisting

structurewithnotlessthan12gaugehangerwireswrappedtightly3fullturns,spaced48inchesoncenter.

2. StabilizerBars:Installedperpendiculartosymmetricalcarrier(24)(36)(48)inchesoncenter.

B. LinearMetalPanelsandAccessories1. LinearMetalPanels:

a. AttachtoMainCarriertabsandconnectwithPanelSpliceswithjointsstaggeredinadjacentrows.

2. Slip-onMoldings:Installonexposedendsofpanels.3. EndPlugs:Installedexposedendsofpanels.4. WallAngles:Installedonverticalsurfacesintersectingsystembyappropriatemethod

inaccordancewithindustryacceptedpractice.5. FillerStrips:Installedintoopenrevealbetweenpanels.6. AccessPanels:Installedinaccordancewithmanufacturersrecommendations.

C. IntegratedAccessories1. Insulationtrimmedtofitandinstalledinplenumbetweencarriers.3.03RepairsA. Removedamagedcomponents,replacewithundamagedcomponents.Cleanwith

non-solvent,non-abrasivecommercialcleaningsolution.

Though Planar/PlanarPlus are meant for interior and exterior applications, Specifications as shown here pertain to interior applications only.

Contact Chicago Metallic for guidelines specifically applicable to exterior use of Planar/PlanarPlus products.


PART1-GENERAL

1.01Scope

ProvideLinearMetalCeilingSystem.

1.02RelatedSections

A. Section095100-AcousticalCeilings

B. Section096300-AcousticalCeilingSuspension

C. Section095400-SpecialtyCeilings

D. Section210000-FireSuspension

E. Section220000-Plumbing

F. Section230000-HVAC

G. Section265000-Lighting

1.03References

A. AmericanSocietyforTestingandMaterials(ASTM)

1. C423-TestMethodforSoundAbsorptionandSoundAbsorptionCoefficientsbytheReverberationRoomMethod.


3. C636-StandardPractice for InstallationofMetalCeilingSuspensionSystems forAcousticalTileandLay-inPanels.

4. E84-TestMethodforSurfaceBurningCharacteristicsofBuildingMaterials.

5. E580-PracticeforApplicationofCeilingSuspensionSystemsforAcousticalTileandLay-InPanelsinAreasRequiringSeismicRestraint.

6. E795-PracticesforMountingTestSpecimensDuringSoundAbsorptionTests.

1.04Submittals

A. Productdata:Manufacturersstandarddatasheetslistingdimensionsanddetails.

B. Samples:Manufacturersstandardsamplesincludingsuspension,panelsandcolors.

C. ShopDrawings:Reflectedceilingplanandelevationdrawingsindicatingceilinglayouts,dimensionsandperimeterconditions.

1.05ProjectConditions

A. EnvironmentalRequirements:

1. Verifyweathertightnesspriortoinstallation.

2. Wettradesworktobethoroughlydryandcompletepriortosuspensionsysteminstal-lation.

3. Installationtobeginonlywhentemperatureandhumidityconditionscloselyapproximateinteriorconditionstoexistwhenareaisoccupied.

4. Heatingandairconditioningsystemstobeoperatingpriorto,during,andafterinstal-lation.

5. Delivermaterialsinmanufacturersoriginalpackaging,unopenedandundamaged.

6. Storematerialsinanencloseddrylocationatroomtemperatureandprotectfromsoiling,damage,moistureandhumidity.

1.06Maintenance

Furnishextramaterialequalto____percentofceilingarea.

PART2-PRODUCTS

2.01Manufacturer

(PlanarMacro)(MacroPlus)linearmetalceilingsystemsasmanufacturedbyChicagoMetallic,4849SouthAustinAvenue,Chicago,Illinois60638.1-800-323-7164.2.02MaterialsA. LinearMetalPanels:

1. a.PlanarMacromanufacturedfrom(0.032)(0.040)inchthickaluminumnominal(4)(6)(8)incheswideby(144)(__)incheslongwithsquareedgesby7/8inchdeep.

b.MacroPlusmanufacturedfrom0.032inchthickaluminumnominal(4)(6)(8)incheswideby(144)(__)incheslongby7/8inchdeep.withsquareedgesandintegralfillerstrips.

2. Finish:(Painted_____)(Reflective_____)(Anodized_____)(MetalWood®laminatedvinyl_____)(WoodScenes™Painted_____).

3. [(Unperforated)(Perforated with pattern T)] [(with)(without)] Acoutex™ non-wovenmembranefactorybondedtopanelbackside.

C. Accessories

1. PlanarMacroRecessedFillerStrips:Manufacturedfromaluminum3/4inchwideby144incheslongcoatedto(matchpanel)(_____color)withlinearmetalpanels.

2. PanelSplices:Manufacturedfrom0.032inchthickaluminum83/4incheslongcoatedwith (blackbaked-onpolyesterenamel)(finish identical to linearmetalpanels),withprofilecompatiblewithlinearpanels.

3. EndPlugs:Manufacturedfrom0.032inchthickaluminumwith(round)(square)edges.Coatedidenticaltolinearmetalpanels.

4. PerimeterTrim a. PerimeterCaps:Manufacturedfrom0.025inchthickaluminum2inchI.D.by15/8

inchtopflangeby1inchbottomflangeby120incheslong.Coatedidenticaltolinearmetalpanels.

b. WallAngles:Manufacturedfrom0.025inchthickaluminum15/16inchwideby3/4inchhighby144incheslongwithhemmededges.Coatedidenticaltolinearmetalpanels.

C.SuspensionSystem1. SymmetricalCarrier: a. Manufacturedtoaninverted“U”shapefrom0.040inchaluminum144incheslong.

Coatedwithblackpolyesterenamel. ArchitectNote:Doublegripcarrierrequiredonallexteriorapplications. b. Slottedatappropriate intervals to receivestabilizingcomponentsasdescribed

below.2. StabilizerBars:Manufacturedfrom0.040inchthickaluminum(4913/16)(3513/16)inch

long.Coatedwithblackpolyesterenamel.3. RadiusCarrier:Manufacturedtoaninverted“U”shapefrom0.040inchthickaluminum

120incheslongwithintegralcarriertabs,paintedblack.4. ExpansionCarrier:Manufacturedtoaninverted“U”shapefrom0.040inchthickalu-

minum144incheslongwithintegralcarriertabsspaced41/8inches.Coatedwithblackpolyesterenamel.

D.AcousticalMaterial1. Blankettypeblackvinylfacedoneside(1)(11/2) inchesthickby(1)(11/2)poundsper

cubicfootdensity.2. Blackmatteductliner1inchthickby11/2poundspercubicfoot.3. Acoutex™non-wovenfiberfactoryadheredtobackofperforatedpanels.

E.AirDiffusion1. AirUnits: a. (2)(4)(6)(8) slot with (8)(10)(12)(14) inches wide (dampered)(undampered) top

mountedcollars. b. Manufacturedfrom0.024inchthicksteelwithgasketedlowerflangesandfactory

appliedacousticalinsulationadheredtointernalsurfaces. c. “L”shapeddirectionalvanespaintedblack. d. Optionalremotecontroldamperassemblywithcontrolcableextendingthroughair

distributionslot.

PART3-EXECUTION

3.01Examination

Examineareareceivingsystemtoidentifyconditionswhichwilladverselyaffectinstallation.Donotbegininstallationuntiladverseconditionshavebeenremedied.

3.02Installation(InteriorOnly)A. SuspensionSystem

1. SymmetricalCarriers:Installed50inchesoncenterbydirectsuspensionfromexistingstructurewithnotlessthan12gaugehangerwireswrappedtightly3fullturns,spaced48inchesoncenter.

2. Stabilizer Bars: Installed perpendicular to symmetrical carrier (24)(36)(48) inches oncenter.

B. LinearMetalPanelsandAccessories1. LinearMetalPanels:

a. AttachtomaincarriertabsandconnectwithPanelSpliceswithjointsstaggeredinadjacentrows.

2. Slip-onMoldings:Installonexposedendsofpanels.3. EndPlugs:Installedexposedendsofpanels.4. WallAngles:Installedonverticalsurfacesintersectingsystembyappropriatemethodin

accordancewithindustryacceptedpractice.5. FillerStrips:Installedintoopenrevealbetweenpanels.6. AccessPanels:Installedinaccordancewithmanufacturersrecommendations.

C. IntegratedAccessories1. Insulationtrimmedtofitandinstalledinplenumbetweencarriers.3.03Repairs

A.Removedamagedcomponents, replacewithundamagedcomponents.Cleanwithnon-solventnon-abrasivecommercialcleaningsolution.non-solventbasednon-abrasivecommercialcleaningsolution.

PlanarMacro® MacroPlus™ Specification DataThough PlanarMacro/MacroPlus are meant for interior and exterior applications, Specifications as shown here pertain to interior applications only.

Contact Chicago Metallic for guidelines specifically applicable to exterior use of PlanarMacro/MacroPlus products.

Literature Disclaimer: Presentations in this brochure or any other Chicago Metallic Corporation publication are correct to the best of our knowledge at time of preparation. We provide this information in an advisory capacity only. Any advisory recommendations given in our publications must be modified to conform with local codes, conditions and specifications. We reserve all rights to amend any information published in our literature without additional notice. Chicago Metallic can not be held responsible or liable for the selection nor application of our products.

Ceiling Systems and Specialty Products - USA and Canada: 800.323.7164 / Fax: 800.222.3744 / www.chicagometallic.combelgium / denmark / the netherlands / uk / germany / france / hong kong / china / malaysia / united arab emirates / mexico

Chicago Metallic, its logo, Planar, PlanarPlus, PlanarMacro and MetalWood II are Registered Trademarks of Chicago Metallic Corporation. Acoutex, Infinity, WoodScenes and MacroPlus are trademarks of Chicago Metallic Corporation.© 2011 Chicago Metallic Corporation All Rights Reserved Printed in USA SNL0085L1311

USA and Canada: 800.323.7164 / fax: 800.222.3744 Planostile Metal Panel 1

MetAl PAnel Ceiling 09 51 33

Planostile™ Metal Panel CeilingsProdUCt gUide

2 Planostile Metal Panel chicagometallic.com

Applicationsideal for exterior soffits, airports, hotels, lobbies, corridors.

Features• Attractiveanddurablemetalpanelsforgrid-based

suspension systems in standard and custom sizes.

• Rangeofprofilesandoptionsoffergreatdesignflexibility.

• Integrateswithvarietyofgridsuspensionsystems.

• Gridsuspensionacceptsindustrystandardlightandair diffusers.

• Standardperforationpatternsandcustomperforating.

• Snap-insystemdesignedtowithstandpositiveandnegativewindpressure(UL580).

• MetalWood™woodgrainandWoodScenes™ painted finishes.

• Enhanceacousticalperformancewithoptionalbacking material.

• Metalcontainsnoorganiccompoundstosupportmoldormicrobialgrowth.

• Buildingsystemintegrationflexibility(HVAC,lighting).

• Sustainable:Aluminum100%recycledcontent,Steel75%.100%locallyrecyclableatendofusefullife.

Planostile™

MetAl PAnel

Lay-in

Square,lay-in(MF/AMF)

9/16, 15/16, 1 3/8

Reveal,lay-in(ME/AME)

5/16

9/16

5/16

9/16

Reveal,lay-in(ME/AME)

15/16

Reveal,lay-in(MC/AMC)

5/16

Snap-in

Snap-insquare(MA/AMA)

2-1/2

Snap-inbevel(MA461/AMA461)

(24 x 24only)

2-1/2


chicagometallic.com/planostile


Lay-inSquareEdgePanels

Product Panel Packaging Number Size Sq. Ft. Pieces Weight

Lay-in Square Edge — for 9/16, 15/16, 13/8 grid0.024 Galvanized Steel MF463XxxxX 24 x 24 56 14 32 MF483XxxxX 24 x 48 Pto* Pto* Pto*

0.024 600 Stainless Steel 2BSolid Only MF463X02BX 24 x 24 56 14 32

0.032 AluminumSolid** AMF463XxxxX 24 x 24 56 14 31 AMF483XxxxX 24 x 48 Pto* Pto* Pto*


Lay-in Reveal Edge — for 15/16 grid0.024 Galvanized SteelSolid MC463XxxxX 24 x 24 64 16 31 MC483XxxxX 24 x 48 Pto* Pto* Pto*

0.032 AluminumSolid AMC463XxxxX 24 x 24 64 16 31 AMC483XxxxX 24 x 48 Pto* Pto* Pto*

(9/16) (15/16) (13/8)

Lay-in Square Edge (MF/AMF)

11/2

Lay-in Reveal Edge (MC/AMC)

(15/16) (15/16) (15/16)

13/4

* Pto – Packaged to order

** MetalWoodIIfinishedaluminumpanelsareconstructedfrom0.024basealuminummetalwith0.008vinyllaminateforatotalpanelthicknessof0.032


Lay-inRevealEdgePanels


Lay-in Reveal Edge— for 9/16 grid0.024 Galvanized SteelSolid Me463XxxxX 24 x 24 64 16 32 Me483XxxxX 24 x 48 Pto* Pto* Pto*

0.032 AluminumSolid** AMe463XxxxX 24 x 24 64 16 31 AMe483XxxxX 24 x 48 Pto* Pto* Pto*

Lay-in Reveal Edge (ME/AME)

(9/16) Square (9/16) Square (9/16)

13/4



USAandCanada:800.323.7164/fax:800.222.3744 PlanostileMetalPanel 5

Main Tee10.00.200

Main Tee10.00.250

Cross Tee10.01.20910.01.229 - No Slots

Main Tee10.04.040

Main Tee10.04.000

Cross Tee10.04.01410.04.022 - No Slots

Wall Angle38.90.124

Wall Channel60.00.010-60.00.011

Lay-inSuspension Product Dimensions Weight Number Length Height Face Slots Per Piece

15/16 GridMain Tee (Heavy Duty) 10.00.200.xxxH 12 11/2 15/16 24 4

Main Tee (Intermediate Duty) 10.00.250.xxxH 12 11/2 15/16 24 3

Cross Tees – Stab-in/Butt Cut 10.01.209.xxxH 4 11/2 15/16 3 1 10.01.229.xxxH 2 11/2 15/16 0 0.5

9/16 GridMain Tee (Heavy Duty) 10.04.040.xxxH 12 11/2 9/16 24 4

Main Tee (Intermediate Duty) 10.04.000.xxxH 12 11/2 9/16 24 3

Cross Tees – Stab-in 10.04.014.xxxCH 4 11/2 9/16 3 1 10.04.022.xxxCH 2 11/2 9/16 0 0.5

Product Weight Number Description Per Piece

Wall Angle – Aluminum with Hemmed Edges38.90.124.xxx 12 x 3/4 x 15/16 1.2*Reflective and Anodized finishes on one side only.

Wall Channel — Steel60.00.010.xxx 10 x 19/16 x 3/4 x 15/16 2.2

Wall Channel — Aluminum60.00.011.xxx 10 x 19/16 x 3/4 x 15/16 2.2


Product Weight Packaging Number Description Per Piece Feet Pieces

Hold Down Inserts for 19/16 Channel — Steel 60.00.012 11 x 11/2 x 3/4 x 3/4 0.2 Pto* 60.00.014 22 x 11/2 x 3/4 x 3/4 0.4 Pto*

Hold Down Inserts for 19/16 Channel — Aluminum 60.00.013 11 x 11/2 x 3/4 x 3/4 0.1 Pto* 60.00.015 22 x 11/2 x 3/4 x 3/4 0.2 Pto*

Product Packaging Number Description Pieces Weight

Miscellaneous Accessories 63.26.200 Black-HoldDownClip 1000 16 63.26.201 PerimeterClip 500 21 63.26.202 WallSpring-5/8 face x 7/8 deep 1000 17 940.xxx Touch-UpPaint,12oz.spraycan – 1 1

Lay-inAccessories

Hold Down Inserts60.00.012-60.00.01360.00.014-60.00.015

Hold Down Clip63.26.200

Perimeter Clip63.26.201

Wall Spring63.26.202

Poly-Wrapped Acoustical Pads58.01.059.008-58.01.064.008

Wire Grid Spacer60.00.0211

Product Panel Weight Number Size Description Per Piece

Poly-Wrapped Acoustical Pads 58.01.059.008 24 x 24 1x1lb. 0.50 58.01.061.008 24 x 48 1 x 1 lb. 1.00 58.01.064.008 24 x 24 11/2x1lb. 0.75 58.01.063.008 24 x 48 11/2x1lb. 1.50

Product Weight Number Description Per Piece

Wire Grid Spacer 60.00.021 2 x 2,Steel 0.50




Snap-in Square Edge0.024 Galvanized SteelSolid MA463XxxxX 24 x 24 56 14 32

0.032 AluminumSolid** AMA463XxxxX 24 x 24 56 14 31 AMA483XxxxX 24 x 48 Pto* Pto* Pto*

Snap-inSquareandBevelEdgePanelsSnap-in Square Edge Panels (MA/AMA)

21/2


Snap-in Bevel Edge0.024 Galvanized SteelSolid MA461XxxxX 24 x 24 56 14 32

0.032 AluminumSolid** AMA461XxxxX 24 x 24 56 14 31

Snap-in Bevel Edge Panels (MA461/AMA461)

21/2




Concealed Snap Bar Main TeeMA010.500CH

Spacer Tee10.04.022UL.001-10.01.229UL.001 10.01.210.001H - 10.01.206.001H

Spacer Bar10.00.826.000H - 10.00.828.000H

Wall Channel60.00.009-60.00.008

Snap-inSuspensionandWallChannels Product Dimensions Packaging Number Length Height Face Feet Pieces Weight

Concealed Snap-Bar Main Tee MA010.500CH* 12 21/8 15/16 180 15 74

Spacer Cross Tee 10.04.022Ul.001* 2 11/2 9/16 200 100 35 10.01.229Ul.001* 2 11/2 15/16 150 75 28 10.01.210.001H 4 11/2 15/16 200 50 38 10.01.206.001H 5 11/2 15/16 250 50 61*Components labeled for U.L. 580 Class 30 system.

Spacer Bar 10.00.826.000 2 1 1 80 40 15 10.00.828.000 4 1 1 160 40 29

Product Dimensions Weight Number Length Height Face Per Piece

Wall Channel — Steel60.00.009.xxx 10 21/2 15/16 x 15/16 4

Wall Channel — Aluminum*60.00.008.xxx 10 21/2 15/16 x 15/16 2.5*Components labeled for U.L. 580 Class 30 system - see drawing on page 11 for additional information.


Product Dimensions Weight Packaging Number Length Height Face Per Piece Feet Pieces

Hold Down Inserts for 21/2 Wall Channel – Steel 60.00.031 11 27/16 3/4 x 3/4 0.5 PTO* 60.00.032 22 27/16 3/4 x 3/4 0.5 PTO*

Hold Down Inserts for 21/2 Channel – Aluminum 60.00.033 11 27/16 3/4 x 3/4 0.2 Pto* 60.00.034* 22 27/16 3/4 x 3/4 0.2 Pto**Components labeled for U.L. 580 Class 30 system - see drawing on page 11 for additional information.

Product Packaging Number Length Description Feet Pieces Weight

Miscellaneous Accessories 923 – AccessKeyBladeAssembly PTO* 924 – AccessKeyBlade* PTO* *Access key blade fits into a standard utility knife handle and is used to disengage tiles from the concealed snap bar.

Product Packaging Number Size Description Feet Pieces Weight

Accessories for UL 580 Class 30 Snap-in System for Exterior Soffits 63.26.031* 4 PanelRetainerClip – 500 7 63.26.032* 3 x 3 BracingtoSnap-BarCarrierAttachmentClip– 100 63.26.035.xxx 120 ExpansionJointAssembly-paintedcolor – PTO* 5 63.26.033.xxx 24 x 24 AccessDoorAssembly-paintedcolor – 1 6*Components labeled for U.L. 580 Class 30 system - see drawing on page 11 for additional information.Expansion Joint Assembly includes two pieces of expansion channel and one piece of expansion angle.

Snap-inAccessories

Hold Down Inserts60.00.031-60.00.03260.00.033-60.00.034

Panel Retainer Clip63.26.031

Attachment Clip Brace63.26.032

Poly-Wrapped Acoustical Pads58.01.059.008-58.01.064.008

Wire Grid Spacer60.00.021

Product Panel Weight Number Size Description Per Piece

Poly-Wrapped Acoustical Pads 58.01.059.008 24 x 24 1x1lb. 0.50 58.01.061.008 24 x 48 1 x 1 lb. 1.00 58.01.064.008 24 x 24 11/2x1lb. 0.75 58.01.063.008 24 x 48 11/2x1lb. 1.50

Wire Grid Spacer 60.00.021 – 2 x 2,Steel 0.50

Product Fixture Per Weight Number Size Carton Per Piece

Trim Kit* – For 24 x 24 Type G Light Fixture - 24 Carrier Spacing 63.26.036.xxx 24 x 24 Pto* 2 63.26.036.xxx 24 x 24 Pto* 2 63.26.036.xxx 24 x 24 Pto* 2

Trim Kit** – For 24 x 48 Type G Light Fixture - 48 Carrier Spacing 63.26.037.xxx 24 x 48 Pto* 4 63.26.037.xxx 24 x 48 Pto* 4 63.26.037.xxx 24 x 48 Pto* 4

Trim Kit* – For 24 x 48 Type G Light Fixture - 24 Carrier Spacing 63.26.038.xxx 20 x 48 PTO* 5 63.26.038.xxx 20 x 48 PTO* 5 63.26.038.xxx 20 x 48 PTO* 5* Kit includes four trim pieces and two variable placement cross tees.** Kit includes four trim pieces and two spacer bars.

Trim Kit 63.26.036- 63.26.037-63.26.038



exterior Soffits

PlanostileSnap-InPanelsystemwillresista30PSFwindpressure(positiveandnegative)wheninstalledasshownandinaccordancewithASTMC636-04.Downbracesselectedbasedontheplenumdepthandimposedaxialloadselectedbyarchitectorengineerof record.

Planostile Snap-in System for Exterior Soffits – Class 30 per UL 580

Panel Retainer Clip (#63.26.031)Insert through holes in panels and twist wrap retainer ends with a minimum (3) tight wraps.

Concealed Snap Bar Main Tee (#MA010.500CH)

Hanger Wire (12 ga min.)

Cross Tee (#4022)

Down Brace (48 maximum spacing along main tee) must be fastened to main tee.

Planostile Snap-In Panel (#AMA 463 or #MA 463) non-perforated. (If steel panels required, use G60 minimum. Special order, consult CMC).

Planostile Lay-in

System integration

Planostile Snap-in

Wallconditionwithangle Wallconditionwithchannel/holddowninsert

infinity™ perimeter trim

Lay-insquarepanel

Lay-inrevealpanel

Wallconditionwithangle Wallconditionwithchannel/holddowninsert

infinity™ perimeter trim

Snap-inpanel

g fixture trim

trim Kit

type glight fixture(byothers)


Specification dataProduct information for integration into ceiling specification

panel type Lay-in Reveal Edge Lay-in Square Edge Snap-inmaterial paintedaluminum • • • paintedgalvanizedsteel • • • MetalWood®woodgrainfinishes*** • • • WoodScenes™paintedfinishes • • • brass,copper,chromeandsatinanodizedaluminum • • • stainlesssteel(solidonly) •surface solidandperforated • • •size 2 x 2 square square square/bevel 2 x 4, custom square square squarefire classA:flame0,smoke0 perASTME84 • • •sound NRC - perforated with Acoutex™ backer 0.70 0.70 0.70 NRC - perforated with 1-1/2 acoustical pad 0.90 0.90 0.90performance interiorandseismicenvironments • • • exterior soffits (per UL 580 class 30) (2 x 2)1 •suspension 9/16 • • 15/16 • • 1-3/8 • concealedsnapbar •classification typeXX,patternC,GperASTME1264 • • •warranty 1yearlimited • • •sustainability Aluminum 100% recycled content (60% post-consumer/ 40% post-industrial). Steel panels 75% recycled content (50% post-consumer/50% post-industrial). 100% locally recyclable • • • 1 - Consult with an engineer to evaluate the suitability of the system for the intended application.

Colors and FinishesStandard Painted Colors 01 White 08 Black 44 Satin Silver

Premium Painted Colors and Finishes 21 Copper Metallic 03 Bronze 88 Flat Black 113 Straw 167 Brick Red 174 Garnet 215 Forest Green 246 Federal Indigo 256 True Blue 263 Plum 270 Pearl Gray 425 Wet Clay 428 Yellow Flash 429 Silver Lining 430 Beige Breeze 432 Blonde Wood 437 Midnight Blue

438 Royal Amethyst 442 Burgundy Brick 443 Toffee Fate 447 Cinnamon 449 Fortune Gray 455 Cocoa Shell 495 Cardinal Red 23 Sandstone 379 Gloss White 386 Gloss Black 401 Maple* 402 Oak* 403 Cherry* 404 Pumpkin Maple* 405 Karri*

431 Whitewash 520 Polar White 521 Nickel 524 Silver Other painted color* Coordinating Solid Paint Colors to MetalWood II ® Woodgrain Finishes

Anodized Finishes

14 Chromecoat 16 Brasscoat 504 Satin Anodized* 509 Coppercoat

** Panels only

WoodScenes™ Painted Colors 800 Lazy Maple

801 Aged Teak

802 Vintage Burlwood

803 Burnished Cherry

804 Sleek Cherry

805 Weathered Oak

MetalWood II ® Woodgrain Finishes*** 650R Maple 651R Cherry 652R Pumpkin Maple 653R Oak 654R Karri 655R Bamboo

** * MetalWood II finished aluminum panels are constructed from 0.024 base aluminum metal with 0.008 vinyl laminate for a total panel thickness of 0.032


Panel Perforation Borders (24 x 24Lay-inPanels) Square Edge for Reveal Edge for Reveal Edge for Pattern Letter Hole Size Hole Type Spacing Pattern % Open Area 15/16 Grid 15/16 Grid 9/16 Snap-in Standard

AA 0.062 Round 0.354 Lineal(straight) 3% none none none none

d 0.098 round 0.216 Lineal(straight) 16% none 1.00 1.19 0.72

e 0.071 round 0.138 Diagonal(45°) 21% none 0.97 1.16 0.66

J 0.250 round 0.312 Staggered(60°) 58% none none none none

Q 0.562 Square 0.672 Lineal(straight) 70% none 0.35 1.02 1.00

R 0.250 Square 0.750 Lineal(straight) 11% 0.53 0.53 0.72 0.25

V 0.062 Round 0.250 Diagonal(45°) 5% none none none none

Note: Border is measured from edge of hole to edge of grid.

Panel Perforation Patterns

J 250R312S0.250 diameter holes0.312 staggered centers58% open area

R 250S750L0.250 square holes0.750 lineal centers11% open area

Q 562S572L0.562 square holes0.672 lineal centers70% open area

V 62R250D0.062 diameter holes0.250 diagonal centers5% open area

D 98R216L0.098 diameter holes0.216 lineal centers16% open area

AA 62R354L0.062 diameter holes0.354 lineal centers3% open area

E 71R138D0.071 diameter holes0.138 diagonal centers21% open area

Standard Patterns

Perforation Code Key

Sample number: 62R250D

62Hole size in 1/1000

inches (0.062”)

RR = Round HoleS = Square Hole

250Hole spacing in 1/1000 inches

(0.250”)

DD=Diagonal pattern (45°)L=Linear pattern (straight)S=Staggered pattern (60°)


Panel Perforation Borders (24 x 24Lay-inPanels) Square Edge for Reveal Edge for Reveal Edge for Pattern Letter Hole Size Hole Type Spacing Pattern % Open Area 15/16 Grid 15/16 Grid 9/16 Snap-in Premium B 0.060 round 0.120 Lineal(straight) 10% 0.437 0.437 0.625 0.900 F 0.071 Round 0.195 Lineal(straight) 10% 0.71 0.71 0.90 0.40 G 0.125 Round 0.250 Lineal(straight) 20% 0.340 0.340 0.581 1.060 H 0.125 Round 0.354 Diagonal(45°) 10% 0.340 0.340 0.562 0.590 i 0.188 round 1.000 Diagonal(45°) 3% none 0.13 0.31 0.59 K 0.250 Round 0.354 Diagonal(45°) 39% 0.280 0.280 0.470 0.750 L 0.250 Round 0.50 Lineal(straight) 19% 0.400 0.400 0.590 0.980 N 0.250 Round 0.750 Lineal(straight) 9% 0.53 0.53 0.72 0.25 O 0.375 Square 1.125 Lineal(straight) 11% 0.65 0.66 0.84 0.31 P 0.375 Round 1.125 Lineal(straight) 9% 0.65 0.66 0.84 0.31 W 0.562 round 1.312 Lineal(straight) 14% 0.75 0.75 0.94 0.66 Y 0.562 Square 1.312 Lineal(straight) 18% 0.75 0.75 0.94 0.56 Z 0.125 Round 0.500 Lineal(straight) 5% 0.437 0.437 0.650 0.730 AI 0.250 round 0.413 Staggered(41°) 28% 0.798 0.798 0.986 1.267 AJ 0.500 round 0.600 Staggered 63% 0.181 0.181 0.369 0.650 AK 0.048 round 0.196 Lineal(straight) 4.7% 0.433 0.433 0.621 0.902Note: Border is measured from edge of hole to edge of grid.

Panel Perforation Patterns

B 60R169L0.060 diameter holes0.120 diagonal centers10% open area

F 71R195L0.071 diameter holes0.195 lineal centers10% open area

G 125R250L0.125 diameter holes0.250 lineal centers20% open area

Z 125R500L0.125 diameter holes0.500 lineal centers5% open area

AI 250R413S0.250 diameter holes0.413 special staggered centers (41°)28% open area

AJ 500R600S0.500 diameter holes0.600 staggered centers63% open area

H 125R354L0.125 diameter holes0.354 lineal centers10% open area

K 250R354D0.25 diameter holes0.354 lineal centers39% open area

L 250R500L0.25 diameter holes0.50 lineal centers19% open area

N 250R750L0.250 diameter holes0.750 lineal centers9% open area

P 375R1125L0.375 diameter holes1.125 diagonal centers9% open area

W 562R131L0.562 diameter holes1.312 lineal centers14% open area

AK 48R196L0.048 diameter holes0.196 lineal centers4.7% open area

Y 562S1312L0.562 square holes1.312 lineal centers18% open area

I 185R1000D0.188 diameter holes1.00 diagonal centers3% open area

O 375S1125L0.375 square holes1.125 lineal centers11% open area

Premium Patterns


Lay-inPanelSpecificationPART1-GENERAL

1.01 Scope

FurnishandinstallthePlanostilelay-inmetalpanelceilingsystemasmanufacturedandsuppliedbyChicagoMetallic(800)323.7164.

1.02 related Sections

A. Section092226-SuspensionSystems

B. Section095100-AcousticalCeilings

C. Section096300-AcousticalCeilingSuspensionAssemblies

D. Section092900-GypsumBoard

E. Section095400-SpecialtyCeilings

F. Section095800-IntegratedCeilingAssemblies

G. Section134800-Sound,Vibration,andSeismicControl

H. Section220000-Plumbing

I. Section235000-CentralHeatingEquipment

J. Section265000-Lighting

1.03 references

A. AmericanSocietyforTestingandMaterials(ASTM)


2. C636-StandardPracticeforInstallationofMetalCeilingSuspensionSystemsforAcousticalTileandLay-inPanels.

3. E84-TestMethodforSurfaceBurningCharacteristicsofBuildingMaterials.

4. E580-StandardPractice forApplicationofCeilingSuspensionSystems forAcousticalTileandLay-inPanelsinAreasRequiringSeismicRestraint.

1.04 Submittals

A. Product data: Manufacturers standard data sheets listing dimensions and de-tails.

B. Samples:Manufacturersstandardsamples includingsuspension,panelsandcolors.

C. ShopDrawings:Reflectedceilingplanandelevationdrawingsindicatingceilinglayouts, perimeter conditions and accessories.

1.05ProjectConditions

A. EnvironmentalRequirements:

1. Verifyweathertightnessofareatoreceivesuspensionsystempriortoinstalla-tion.

2. Wettradesworktobethoroughlydryandcompletepriortosuspensionsysteminstallation.

3. Installation to begin only when temperature and humidity conditions closelyapproximateinteriorconditionswhichwillexistwhenareaiscompleteandoc-cupied.

4. Heatingandairconditioningsystemstobeoperatingpriorto,during,andafterinstallation.

5. Delivermaterialsinmanufacturersoriginalpackaging,unopenedandundam-aged.


1.06 Maintenance

Furnishadditionalmaterialequalto(_____)%ofceilingarea.

PART2-PRODUCTS

2.01 Manufacturer

ChicagoMetallicnon-ratedPlanostilelay-inmetalpanelceilingsystemforinstallationintoexposedT-barceilingsuspension.

2.02 Materials

A. Lay-inmetalpanels:

1. Panelsshallmeasure(24in.by24in.)(24in.by48in.)(custom_________)with(square)(reveal)lay-inedgedetail.

2. Manufactured from [(0.024 in.galvanizedsteel) (0.032 in.aluminum)] [(solid)(perforatedwithChicagoMetallicpattern___)].

3. Finish: [Painted: (01 White)(44 Satin Silver) (Painted Color__________)(An-odized________) (MetalWood® finish _________ on 0.032 inch aluminum)(WoodScenes™PaintedColor______)].

B. AcousticalMaterial:

1. Poly-encased insulationpads,of (1)),(1-1/2)) thicknessandadensityof (1)),(1-1/2))pcf.

2.Acoutexacousticalnon-wovenfibertobeinsertedinthefactoryandadheredwithgluetothebackofthepanelforsoundabsorptioncapabilities.

C. Suspension:

1. Chicago Metallic Intermediate duty non-rated double web suspension (1200systemwith15/16 inchexposed face) (4000systemwith9/16 inchexposedface)(3500systemwith9/16inchwideby5/16inchdeepfacewith1/4inchwideopening)(3600systemwith9/16inchwideby5/16inchdeepfacewith1/8inchwideopening).Systemconsistsofmainteesandcrossteestocreate(24inchby24inch)(24inchby48inch)(custom_________)modules.

2. Suspensionexposedfaceshallbe[(coatedwithfactoryappliedbaked-onenamelpaint)(01White)(44SatinSilverMetallic)(_____)][anodized(14Chromecoat)(16Brasscoat)(509Coppercoat)][paintedcolorcoordinatedforwoodgrainpanelfinish].

d. Perimeter treatment Components:

1. WallChannelsandhold-downinserts:Wallchannelsareformedfrom0.020inch(galvanizedsteel)(aluminum)andmanufacturedtoaC-shape,witha¾inchtoplegby1-9/16I.D.and15/16inchbottomleg.Lengthis144.Finishedidenticaltomainteesandcrosstees.Hold-DownInsertsaremanufacturedfromthesamematerialaswallchannelsandformedinaC-shapewith¾inchlegswith1½inchI.D.by(11inch)(22inch)length.Finishshallbesuppliedbymanufacturer.

2. WallAngle:(C3209,1inchwidex2incheshighx120incheslong)(1430,7/8inchwideby7/8inchhighx144incheslong)finishedidenticaltomainteesandcross tees.

3. Infinity™PerimeterTrim:Made fromextrudedaluminum [(2)(4)(6)(8)(10)(12)]inchesdeep.Paintedonallsides[(tomatchmainteesandcrosstees)(Otherpaintedcolor_________)].Panelstobe(straight)(curved)asindicatedonreflectedceiling plans.

E. HangerWire:

1. Hangerwire:galvanized.

PART3-EXECUTION

3.01 examination

Examineareareceivingsystemtoidentifyconditionswhichwilladverselyaffectinstal-lation.Donotbegininstallationuntiladverseconditionshavebeenremedied.

3.02 installation

A. MetalpanelssupportedbyanappropriatelyinstalledChicagoMetallic(15/16))(9/16))gridsystem.

B. Ifrequired,insulationpadsshallbelaiduponthebackofthepanels(3)max.or1lb/sq.ft.max.).

C. Ifnecessary,utilizeChicagoMetallicholddownclipstokeeptheinsulationpadsin place.

d. Perimeter treatment:

1. Perimetertreatment:Installchannelonverticalsurfaces,intersectingsuspen-sioncomponents,byappropriatemethodinaccordancewithindustryacceptedpractice.

2. Hold-downinsertsinstallbetweenthetoplegofthewallchannelandallmetalpanels.

3. AdditionalHangerWiresatlocationswhereimposedloadscouldcausedeflectionexceeding 1/360 span.

3.03 repair

A. Removedamagedcomponents,replacewithundamagedcomponents.Cleanwithnon-solventbasednon-abrasivecommercialcleaningsolution.

USAandCanada:800.323.7164/fax:800.222.3744 PlanostileMetalPanel 15

PART 1 - GENERAL

1.01 Scope

Furnish and install the Planostile snap-in metal panel ceiling system as manufactured and supplied by Chicago Metallic (800)323.7164.


A. Section 09 20 00 - Plaster and Gypsum Board

B. Section 09 51 00 - Acoustical Ceilings

C. Section 09 63 00 - Acoustical Ceiling Suspension

D. Section 09 54 00 - Specialty Ceilings

E. Section 21 00 00 - Fire Suspension

F. Section 220000 - Plumbing

G. Section 23 00 00 - HVAC

H. Section 26 50 00 - Lighting

1.03 References

A. American Society for Testing and Materials (ASTM)

1. C635 - Standard Specification for the Manufacture, Performance, and Testing of Metal Suspension Systems for Acoustical Tile and Lay-in Panel Ceilings.


3. E 84 - Test Method for Surface Burning Characteristics of Building Materials.

4. E 580 - Standard Practice for Application of Ceiling Suspension Systems for Acoustical Tile and Lay-in Panels in Areas Requiring Seismic Restraint.

B. International Building Code (IBC)

1. Section 1621

C. Uniform Building Code

1. 25-2 Standard

1.04 Submittals



C. Shop Drawings: Reflected plan and elevations indicating ceiling layouts, perimeters and accessories.

1.05 Quality Assurance

A. Materials flame and smoke tested per ASTM E 84 and comply with ASTM E 1264 Class A.

B. Exterior soffit system classified per UL Construction #630 tested per UL 580 Class 30 pressures in both inward (uplift) and outward (negative) directions.



1. Verify weather tightness of area to receive suspension system prior to installation.


3. Installation to begin only when temperature and humidity conditions approximate interior conditions which will exist when area is complete and occupied.

4. Deliver materials in manufacturers original packaging, unopened and undamaged.

5. Store materials in an enclosed dry location at room temperature and protect from damage.

1.07 Maintenance

Furnish additional material equal to (_____) % of ceiling area.

PART 2 - PRODUCTS

2.01 Manufacturer

Chicago Metallic non-rated Planostile (interior)(exterior) snap-in metal panel ceiling system.

2.02 Materials

A. Suspension system:

1. Main Tee MA 010.500CH: Snap-bar formed into T-shape to receive the vertical flanges of Planostile panels with tight panel interlock, alignment and adjacent panels level at the ceiling plane. Formed from 0.020 in. HDG steel.

2.Spacer Tee (2 ft and4 ft): Manufactured from 0.012 in. galvanized steel formed into T-shape (24) (48) (60) (___) in. long.

3.Panel Retention Clip 63.26.031 for UL 580 Class 30 exterior soffits: Formed from 16 ga. galvanized steel wire into angled V shape to interlock four panel corners to Main Tee.

4. Brace Clip 63.26.032 for UL 580 Class 30 exterior soffits: Manufactured from .040 in. galvanized steel for fastener attachment to suspension and bracing.

5. Structural bracing to meet requirements of UL 580 Class 30 classification and specified project design requirements.

B. Metal Panels:

1. Planostile Snap-In Metal Panels for interior applications

a. Panels shall measure (24 in. x 24 in.), (24 in. x 48 in.), (custom _______) with 90° upturned legs on all four sides. Panels shall be formed with (square)(bevel) edges.

b. Panels formed from [(.024 in. galvanized steel)(.032 in. aluminum)] [(perforation pattern ___ ) (unperforated)].

c. Finish: [Painted: (01 White)(44 Satin Silver) (Painted Color__________)(Anodized________) (MetalWood® finish _________ on 0.032 inch aluminum) (WoodScenes™ Painted Color ______)].

2. Planostile Snap-In Metal Panels for exterior soffits:

a. Panels shall measure 24 in. x 24 in. with 90° upturned

legs on all four sides. Panels shall be formed with (square)(bevel) edges.

b. Panels formed from 0.032 in. aluminum, unperforated.

c.Finish to be [painted with a baked enamel finish (01 White) (44 Satin Silver Metallic) (_____)].

3. Acoustical material for interior applications:

a. Glass fiber insulation pads encased in black poly [(1),(1-1/2)] in. thick and density of [(1) (1-1/2)] pcf.

b. Acoutex acoustical non-woven fiber adhered with glue to the back of the panel. Soundtex color is black.

C. Perimeter Treatment:

1. Interior Wall Channel and Hold-Down Insert: Channel made from .020 in. galvanized steel in C-shape, with a 3/4 in. top leg, 2-1/2 in. I.D., and a 15/16 in. bottom leg. Length 144 in. Hold-Down Insert formed from same material as wall channel in a C-shape, with 3/4 in. legs, 2-7/16 in. I.D., (11)(22) in. long.

2. Infinity™ Perimeter Trim: Made from extruded aluminum [(4)(6)(8)(10)(12)] inches deep. Painted on all sides [(to match main tees and cross tees)(Other painted color _________)]. Panels to be (straight)(curved) as indicated on reflected ceiling plans.

3. Exterior Wall Channel and Hold-Down Insert: Channel made from .032 in. aluminum in C-shape, with 3/4 in. top leg, 2-1/2 in. I.D., and 2 in. bottom leg. Hold-Down Insert is formed from same material as wall channel in C-shape, with 3/4 in. legs, 2-7/16 in. I.D., 22 in. long.

D. Accessories

1. Interior panel access key provided to permit detachment of panels from the carrier.

2. Exterior panel access door assembly in same size and finish as panels. Four exposed fasteners lock to the suspension support angles.

3. Expansion Joints: Formed from 0.032 in. aluminum into a C-shape, with 1-3/4 in. top leg, 2-1/2 in. I.D., and 2 in. bottom leg. Top angle to be formed from same material with ½ in. vertical and 4 in. horizontal leg.

4. Interior Trim Kit for (24 in. x 24 in.)(24 in. x 48 in.) Type G fluorescent light fixture including two variable placement 01 White cross tees and trim (01 White)(to match Planostile panels)(other color _____).

5. Bracing bracket at connection between structural bracing and Planostile suspension.

6. Hanger Wire: galvanized.

PART 3 - EXECUTION

3.01 Examination

A. Examine area receiving system to identify conditions which will adversely affect installation. Do not begin installation until adverse conditions have been remedied.

B. Verify completion of work above ceiling plane prior to panel installation.

3.02 Installation

A. General:

1. For interior applications in non seismic areas install in accordance with ASTM C636 (see 1.03, A 2.).

2. For interior applications in seismic areas install in accordance with (IBC Section 1621)(ASTM E 580).

3. For exterior soffit applications install in accordance with ASTM C636 (see 1.03, A 2.)

B. Suspension:

1. Planostile Snap-Bar Main Tees: Install (24)(48) in. O.C., by direct suspension from existing structure, with not less than 12 gage steel hanger wires spaced (48) in. O.C. along main tee length. Wrap hanger wires tightly 3 full turns at each end. (Brace against wind uplift as necessary to meet UL 580 Class 30).

2.Cross Tees: Install perpendicular to main tees 48 in. O.C.

C. Metal Panels:

1. Planostile Snap-in Metal Panels: Install Metal Panel into Main Tee carrier ensuring embosses on vertical legs are fully engaged into Main Tee and panel edges are aligned.

2. If required, insulation pads shall be laid upon the back of the panels (3) max. or 1 lb/sq.ft. max.).

3. For Seismic and Exterior Soffit applications install wire retention clips through holes in panel vertical flanges, connecting four panel corners together and secure by tying wire clips across top of Snap-Bar Main Tee.

D. Perimeter Treatment:

1. Perimeter treatment: Install channel on vertical surfaces, intersecting suspension components, by appropriate method in accordance with industry accepted practice.

2. Hold-down inserts install between the top leg of the wall channel and all metal panels.

3. Additional Hanger Wires at locations where imposed loads could cause deflection exceeding 1/360 span.

E. Air Diffusers: coordinate with Mechanical (HVAC) Division.

3.03 Repair


Snap-inPanelSpecification


C H I C A G O M E T A L L I C ®

Elevate Your Ceilings Accelerate Your Projects Celebrate Your Success

4849 SOUTH AUST IN AVE. , CH ICAGO, I L 60638 708.563.4600 USA & CANADA 800.323.7164 CH ICAGOMETALL IC .COM

© 2013 Chicago Metallic Corporation. All rights reserved. SNL0091B1813

metal panel09 54 33

Traditions™

product guide


Traditions™ Embossed Metal PanelsFeatures and Benefits:

Range of patterns to suit varied designs.

Bare chromium treated steel (suitable for painting) for superior aesthetics and corrosion resistance.

2 x 2 or 2 x 4 Lay-in panels designed for use with stan-dard 15/16 T-bar grid allow for full plenum accessibility.

2 x 4 Nail-up panels are available for ceiling and/or wall applications. Nail-up panels are installed onto furring strips.

Perimeter angles, cornices, and accessories are available for a complete, authentic installation.

Ideal for applications such as restaurants, night clubs, hotels, casinos, lobby areas, retail stores, and private resi-dences.

ColorsStandard Painted Colors

l 01 Whitel 08 Blackl 44 Satin Silver

Premium Painted Colors and Finishes

l 03 Bronzel 21 Copper Metallicl 23 Sandstonel 88 Flat Blackl 113 Strawl 167 Brick Redl 174 Garnetl 215 Forest Greenl 246 Federal Indigol 256 True Bluel 263 Pluml 270 Pearl Grayl 379 Gloss Whitel 425 Wet Clayl 428 Yellow Flashl 429 Silver Liningl 430 Beige Breezel 431 Whitewashl 432 Blonde Woodl 437 Midnight Bluel 438 Royal Amethystl 442 Burgundy Brickl 443 Toffee Fatel 447 Cinnamonl 449 Fortune Grayl 455 Cocoa Shelll 495 Cardinal Redl 510 Morning Dew Metallicl 511 Autumn Metallicl 512 Moon Glow Metallicl 513 Sun Gold Metallicl 514 Harvest Metallicl 515 Sterling Metallicl 516 Flint Metallicl 517 Emerald Metallicl 520 Polar Whitel 521 Nickel

Flat Lay-In Panel(2 x 2 or 2 x 4)

use with standard 15/16 T-bar gridfor full plenum accessibility

(hold down clips or gypsum lay-in panel required)

Full Ceiling Panel

Partial Ceiling Panel 1/2 Nail

Cone Head Nails(required) Cornice

Molding

Cone Head Nail(optional)

Drywall

Nail-up Panel/Cornice(2 x 4)

nails directly to furring strips positioned 12 O.C. (2 x 2)

Furring Strips - 12 OC

2


chicagometallic.com/traditions


UPDATES

0 1 2 3 4

5 6 7 8 9

10 000 Standard Filler Panel 21 23 26

Panel Patterns

37 (1x 2)

Standard nail-up installation procedures are not applicable to pattern 36. This panel requires special installation techniques using 1 x 2 furring strips for attachment. Proper installation instructions are available in the CMC Tech Data literature series or by contacting Customer Service. These patterns are available in Bare (000) only.

Available in 2x 4 only.

36 38 (1x 1)

3

Product Number Key

Product Number Pattern Finish Weight Per Piece

Panels2 x 2 LAY-IN

63.22.xxx.000 0-10, 21, 23, 26 & 36 Bare (000) 2

63.22.xxx.xxx 0-10, 21, 23, 26 & 36 Standard painted colors 2

63.22.xxx.xxx 0-10, 21, 23, 26 & 36 Premium colors and finishes 2

2 x 4 LAY-IN

63.24.xxx.000 0-8, 10, 21, 23, 26 & 36 Bare (000) 4

63.24.xxx.xxx 0-8, 10, 21, 23, 26 & 36 Standard painted colors 4

63.24.xxx.xxx 0-8, 10, 21, 23, 26 & 36 Premium colors and finishes 4

2 x 2 NAIL-uP

63.23.036.000 36 Steel – Bare 2

63.23.036.xxx 36 Steel – Standard Colors 4

63.23.036.xxx 36 Steel – Premium Colors 4

2 x 4 NAIL-uP

63.25.xxx.000 1, 3 Steel – Bare 2

63.25.xxx.000 0, 2, 4, 21, 23, 26, 36 Steel – Bare 2

63.25.xxx.xxx 0-4, 21, 23, 26, 36 Steel – Standard Colors 4

63.25.xxx.xxx 0-4, 21, 23, 26, 36 Steel – Premium Colors 4

63.22.011.001 Finish 000 Bare (suitable for painting) xx (01 /44) White / Satin Silver

xxx Premium Colors and Finishes

Pattern Number

Product 22 2 x 2 Lay-in Panel 24 2 x 4 Lay-in Panel 25 2 x 4 Nail-up Panel 26 2 x 4 Filler Panel 40 Cornice

63 Traditions

4

CornicesCornices need to be field bent to achieves the projections shown below.

— recommended for nail-up panel ceiling installations only —

63.40.035 (31/2 Projection) > Convex Face

63.40.020 (2 Projection) > Convex Face

6�

63.40.050 (4 Projection) > Concave Face


63.40.075 63.40.015 Girder Nosing Pattern

6

3

63.40.030 (3 Projection) > Straight Face


61/4

63.40.063 (61/4 Projection) > Concave Face

5

Product Nominal Dimensions Number Length Height Projection Weight Finish

Cornices 63.40.020.000 4 2 2 .75 Bare (000) 63.40.020.xxx 4 2 2 .75 Standard painted colors 63.40.020.xxx 4 2 2 .75 Premium colors and finishes

63.40.035.000 4 31/2 31/2 .75 Bare (000) 63.40.035.xxx 4 31/2 31/2 .75 Standard painted colors 63.40.035.xxx 4 31/2 31/2 .75 Premium colors and finishes

63.40.040.000 4 4 4 1 Bare (000) 63.40.040.xxx 4 4 4 1 Standard painted colors 63.40.040.xxx 4 4 4 1 Premium colors and finishes



63.40.060.000 4 6 6 1.50 Bare (000) 63.40.060.xxx 4 6 6 1.50 Standard painted colors 63.40.060.xxx 4 6 6 1.50 Premium colors and finishes

63.40.063.000 4 61/4 61/4 1.75 Bare (000) 63.40.063.xxx 4 61/4 61/4 1.75 Standard painted colors 63.40.063.xxx 4 61/4 61/4 1.75 Premium colors and finishes

Perimeter TreatmentFILLER PANELS – 2 x 4 Nail-up For Perimeter use 63.26.xx.000 2 x 4 Steel-Bare (000) 63.26.xx.xxx 2 x 4 Steel-Painted White

AccessorieshoLd dowN CLIP 935.00 – 1000 16 Steel

hoLd dowN CLIP 935.00

6

Specification Guidelines09 54 33 - Decorative Panel Ceilings

PART 1 - GENERAL1.01 Section IncludesA. Provide Stamped Ceiling and Wall Panel

System.

1.02 Related SectionsA. Section 09120 Ceiling Suspension

SystemsB. Section 09130 Acoustical Suspension

SystemsC. Section 09545 Special Ceiling SurfacesD. Section 13020 Integrated AssembliesE. Section 13080 Sound, Vibration, and

Seismic ControlF. Section 15550 Heating, Ventilating, and Air

ConditioningG. Section 16500 Lighting

1.03 ReferencesA. American Society for Testing and Materials

1. C-423 - Test Method for Sound Absorp-tion and Sound Absorption Coefficients by the Reverberation Room Method.

2. C-635 - Standard Specification for the Manufacture, Performance, and Testing of Metal Suspension Systems for Acousti-cal Tile and Lay-In Panel Ceilings.

3. C-636 - Standard Recommended Practice for Installation of Metal Ceiling Suspension Systems for Acoustical Tile and Lay-In Panels.

4. E-84 - Test Method for Surface Burning Characteristics of Building Materials.

5. E-580 - Practice for Application of Ceiling Suspension Systems for Acoustical Tile and Lay-In Panels in Areas Requiring Seismic Restraint.

6. E-795 - Practices for Mounting Test Specimens During Sound Absorption Tests.

1.04 SubmittalsA. Product/Technical Literature

1. Submit descriptive literature along with installation recommendations.

B. Samples1. Submit sample kit containing appropri-

ate Metal Ceiling and Wall Panel System samples.

C. Shop Drawings1. Submit shop drawings illustrating appro-

priate placement of panels.D. Certification

1. Furnish certification of materials and system conforming to specification requirements.

2. Provide written warranty against defec-tive workmanship and materials for a period of __ year(s) (up to 20 yrs. maxi-mum) from filing notice of completion.

1.05 Project ConditionsA. Environmental Requirements

1. Verify weather tightness of area to re-ceive system prior to installation.

2. Installation to begin only when tem-perature and humidity conditions closely approximate interior conditions that will exist when area is complete and occu-pied.

B. Trade Requirements1. Heating or cooling systems to be operat-

ing prior to, during, and after installation.2. Wet trades work shall be dry and com-

plete prior to installation.

1.06 MaintenanceA. Replacement Material

1. Furnish additional material equal to __% of the ceiling system area.

PART 2 - PRoduCTS2.01 ManufacturerA. Traditions Embossed Metal Panels as

manufactured by Chicago Metallic, 4849 South Austin Avenue, Chicago, Illinois 60638. 1-800-323-7164.

2.02 ComponentsA. Stamped Panels:

1. Traditions pattern ( _________).2. Manufactured from (0.010 inch thick tin-

free steel). Nominal (2 x 2)(2 x 4).3. Finish: [Bare 000 with chromium treat-

ment for field painting][baked-on polyes-ter enamel paint (white 001)(____)]

B. Suspension System Components1. Main Runners:

a. Manufactured from 0.015 inch thick steel 15/16 inch wide by 1-1/2 inches high by 144 inches long, with factory punched cross tee slots, hanger holes and integral bayonet-style couplings.

b. Capped and coated with [baked-on polyester enamel paint(white 001)

2. Cross Tees:a. Manufactured from 0.015 inch thick

steel 15/16 inch wide by 1-1/2 inches high by (24)(48) inches long with fac-tory punched cross tee slots,hanger holes, and staked-on stab-in end couplings.

b. Capped and coated identical to main runners.

C. Perimeter Treatments1. Wall Angle:

a. Manufactured from (0.020 inch thick steel)(0.024 inch thick aluminum) 3/4 inches wide by 15/16 inches high by 144 inches long with both edges hemmed.

b. Capped and coated identical to main runners.

2. Cornices:a. Traditions cornice pattern [__].b. Manufactured from (0.010 inch thick

steel) with (2)(2-1/2)(3-1/2)(4)(5)(7-1/2) inch projection by 48 inches long.

c. Coated identical to stamped panels.C. Accessories

1. Conehead nails: Manufactured with [(bare000)(white001)] finish.

PART 3 - ExECuTIoN3.01 InstallationA. Examine area receiving Stamped Ceiling

and Wall Panel System to identify condi-tions which will adversely affect installa-tion. Do not begin installation until adverse conditions have been remedied.

B. Verify completion of work above ceiling plane prior to installation.

3.02 InstallationA. Lay-In Panels:

1. Supported by an appropriately installed Chicago Metallic ceiling grid system.

2. Install backing material, e.g., acoustical board, gypsum board, insulation pads, etc., on the plenum side of the panels.

3. Attach two hold down clips along each side of the panel.

B. Nail-Up Panels: Supported by an appropri-ately installed furring system per detailed instructions provided by Chicago Metallic.

C. Cornices: Installed in accordance with detailed instructions provided by Chicago Metallic.

3.03 RepairA. Remove damaged components, replace

with undamaged components. Clean with mineral spirits per detailed instructions provided by Chicago Metallic.

7

Literature Disclaimer: Presentations in this brochure or any other Chicago Metallic Corporation publication are correct to the best of our knowledge at time of preparation. We provide this information in an advisory capacity only. Any advisory recommendations given in our publications must be modified to conform with local codes, conditions and specifications. We reserve all rights to amend any information published in our literature without additional notice. Chicago Metallic can not be held responsible or liable for the selection nor application of our products.

Ceiling Systems and Specialty Products - USA and Canada: 800-323-7164 / Fax: 800-222-3744 / www.chicagometallic.combelgium / denmark / the netherlands / uk / germany / france / hong kong / china / malaysia / united arab emirates / mexico

Chicago Metallic and its logo are Registered Trademarks of Chicago Metallic Corporation. Traditions is a trademark of Chicago Metallic Corporation.© 2012 Chicago Metallic Corporation All Rights Reserved Printed in USA SNL0095F2012

be modified to conform with local codes, conditions and...

Documents

Transcript of be modified to conform with local codes, conditions and...