Bcmsn lab manual v4

Cisco Certified Network Professional CCNP

BCMSN Lab Manual

Revision 1

Developed by

M. Irfan Ghauri M. Rizwan Khan

Etronics Solution Provider C-32/1 Block-5 Gulshan-e-Iqbal, Karachi ESP Press Ph #021-6034003 Copyrights 2008

LAB.

LABS DESCRIPTION

PAGE NO.

1

Basics of Native IOS

1

2

Configuring VLAN and VTP

6

3

Configuring Traditional Spanning Tree Protocol (PVST)

8

4

Vlan Load Balancing in PVST

9

5

Configuring Uplink fast and Port fast

11

6

Configuring RSTP and MST

13

7

Configuring Inter-Vlan Routing

16

8

Securing STP (Root Guard, Bpdu Guard)

20

9

Configuring Ether Channel

22

10

Configuring HSRP

25

11

Securing Switched network using VACL

27

12

Securing Switched network using Private Vlans

29

13

Securing Switched network using Port Security

31

14

Implementing Wireless Lan using Cisco Aironet Access Point

33

15

Configuring Cisco IP Telephony using Cisco Call Manager &

Cisco IP Phones

52

BCMSN Lab Manual

- 1 -

Lab # 1

Basics of Native IOS Objective This lab includes basic commands of Native IOS on 2950 & 3560. Diagram

2950 3560

Configuratio Step 1: After con Switch con0 is now a Press RETURN to ge Switch>

Etronics Solution P

Console Port 0
Console Port 0
n

necting your PC to the Console Port.

vailable

t started.

(User Mode)

rovider

BCMSN Lab Manual

- 2 -

Step 2: To Enter Into Privilege executive mode From User Mode & Vice- Versa. Switch>enable Switch# Switch#disable Switch> Step 3: To Enter Into Global Configuration Mode. Switch# Switch#config t Switch(config)# Step 4: To change the Host Name of Switch. Switch(config)#hostname 3560 Step 5(A): Set the Line Console Password on the switch. 3560(config)#line console 0 3560(config-line)#password cisco 3560(config-line)#login Step 5(B): Verification Line Console Password on the switch. 3560 con0 is now available Press RETURN to get started. User Access Verification Password: 3560>enable Step 6(A): Set the privileged mode password in clear text. 3560(config)#enable password cisco Step 6(B): Verifying the privileged mode password in clear text. 3560#disable 3560>enable Password:

Etronics Solution Provider

BCMSN Lab Manual

- 3 -

Step 7(A): Set the Privileged Mode password in encrypted form. 3560(config)#enable secret cisco1 Step 7(B): Verifying the Privileged Mode password in encrypted form. 3560#disable 3560>enable Password: Step 8: Set the Line VTY Password on the switch. 3560(config)#line vty 0 15 3560(config-line)#password cisco 3560(config-line)#login Step 9: Show contents of Current Configuration (RAM). 3560#show running-config Step 10: To give the IP Address of Management Domain Interface OF 3560. 3560(config)#int vlan 1 3560(config-if)#ip address 10.0.0.10 255.0.0.0 3560(config-if)#no shutdown Step 11: Display the information of Management VLAN Interface. 3560#show int vlan 1 Step 12: Display the information of All Interfaces on the switch. 3560#show ip interface brief Step 13: Set a IP Default Network In a Switched Network. 3560(config)#ip default-gateway 10.0.0.1 Step 14: Display the Flash Information. 3560#dir Etronics Solution Provider

BCMSN Lab Manual

- 4 -

OR 3560#show flash: Step 15: Display the Status of the Interfaces on the switch. 3560#show interfaces status Step 16: Display the Detailed Information of Interfaces. 3560#show interfaces OR 3560#show interfaces fastEthernet 0/1 Step 17: Display the Information of the Mode of Interfaces (Switchport). 3560#show interfaces switchport OR 3560#show interfaces fastEthernet 0/1 switchport Step 18: Display the Detailed Information of Interfaces Capabilities. 3560#show interfaces capabilities OR 3560#show interfaces fastEthernet 0/1 capabilities Step 19: Display the Information of the Trunk Interfaces (Ports). 3560#show interfaces trunk Step 20: Display the Version Information of the Switch. 3560#show version Etronics Solution Provider

BCMSN Lab Manual

- 5 -

Step 21: Display the Information of Dynamic Trunking Protocol (DTP). 3560#show dtp Step 22: Display the Information of CDP. 3560#show cdp Step 23: Display the Information of CDP Enabled Interfaces. 3560#show cdp interfaces Step 24: Enabled the CDP on the switch. Switch(config)#cdp run Step 25: Enable CDP on the Interface FastEthernet 0/1. Switch(config)#interface fastethernet 0/1 Switch(config-if)#cdp enable Step 26: Shown the MAC Address Table Information. 3560#show mac address-table dynamic Step 27: Copy the Current Configuration Into Startup Configuration. 3560#copy running-config startup-config Step 28: Configuring the Multiple Interfaces. 3560(config)#int range fastEthernet 0/1 - 5 3560(config-if-range)#switchport mode access Step 29: Setting Of Speed, Duplex and Description On Interface. 3560(config)#int fastEthernet 0/1 3560(config-if)#speed 100 3560(config-if)#duplex full 3560(config-if)#description Fast-Ethernet-Port-1


BCMSN Lab Manual

- 6 -

Lab # 2

VLAN & VTP Objective To understand VLAN & VTP operations in switched environment.

i. VLAN Diagram

Switch

Con 0

Switch (2950 / 3560) Switch(config)#vlan 2 Switch(config-vlan)#name esp Switch(config)#interface fastEthernet 0/1 Switch(config-if)#switchport mode access Switch(config-if)#switchport access vlan 2 Verifying Commands Switch#show vlan Switch#show mac address-table dynamic


BCMSN Lab Manual

- 7 -

ii. VLAN Trunking Protocol (VTP) Diagram

VTP Domain CISCO

VTP Mode: SERVER VTP Mode: CLIENT 2950-SWB 2950-SWA

Fastethernet 0/24 Fastethernet 0/24Con 0 Con 0

Switch (2950 / 3560) Switch(config)#vtp domain CISCO Switch(config)#vtp mode [ client | server ] Verifying Commands Switch#show vtp status Switch#show vlan


BCMSN Lab Manual

- 8 -

Lab # 3

Spanning Tree Protocol Objective To understand the Spanning tree protocol operation in switched environment. Diagram

Switch (2950-SWB) Switch(config)#spanning-tree vlan 1 priority 0 Switch (2950-SWA) Switch(config)#int fastethernet 0/24 Switch(config-if)#spanning-tree vlan 1 cost 18 Verifying Commands Switch#show spanning-tree Switch#show spanning-tree vlan 1

Con 0

Priority: 32768 Priority: 0 Root Switch

MAC: 0012.43a0.b840 MAC: 0012.43a0.b940

Fa 0/23 Fa 0/23 2950-SWB 2950-SWA Blocked Port Designated Port

Fa 0/24 Fa 0/24 Con 0 Designated Port Root Port

Non Root Switch


BCMSN Lab Manual

- 9 -

Lab # 4

Vlan Load Balancing in PVST Objective To understand Vlan Load Balancing in PVST. Diagram

MAC: 0012.43a0.b840 MAC: 0012.43a0.b940

Fa 0/23 Fa 0/23

Switch (2950-SWA) Switch(config)#vlan 10 Switch(config)#vlan 20 Switch(config)#spanning-tree vlan 10 priority 0 Switch (2950-SWB) Switch(config)#vlan 10 Switch(config)#vlan 20 Switch(config)#spanning-tree vlan 20 priority 0

Con 0

2950-SWB 2950-SWA

Fa 0/24 Fa 0/24 Con 0

Root Switch for Vlan 10

Root Switch for Vlan 10


BCMSN Lab Manual

- 10 -

Verifying Commands Switch# show spanning-tree vlan 10 Switch# show spanning-tree vlan 20


BCMSN Lab Manual

- 11 -

Lab # 5

Tuning Spanning Tree Protocol

(Port-Fast, Uplink-Fast) Objective Tune the spanning tree protocol for enhancing network performance and minimizing the network downtime by enabling port-fast & uplink-fast features.

i. Port Fast Port Fast is used to bypass the STP Timers for connected PCs and Servers. Diagram

3560

2950 Fa0/1 Fa0/1

10.0.0.1 10.0.0.2 Switch (2950 / 3560) Switch(config)#interface fastEthernet 0/1 Switch(config-if)#spanning-tree portfast Verifying Commands Switch#show running-config interface fastEthernet 0/1


BCMSN Lab Manual

- 12 -

ii. Uplink Fast Uplink Fast enables fast uplink failover on an access layer switch when dual uplinks are connected into the distribution layer switch. Diagram

Non Root Switch Root Switch Designated Port Root Port

3560 Fa0/23 Fa0/7

2950 Fa0/24

Con 0 Fa0/8 Designated Port

Blocked Port Con 0

Switch (3560) 3560(config)#spanning-tree uplinkfast Verifying Commands 3560#show spanning-tree uplinkfast 3560#show spanning-tree vlan 1


BCMSN Lab Manual

- 13 -

Lab # 6

Rapid Spanning Tree Protocol &

Multiple Spanning Tree Lab Objective :

1. Enable RSTP on cisco catalyst switches. 2. Enable MST on cisco catalyst switches.

i. RSTP

Diagram 3560 Fa0/23 Fa0/7

2950 Fa0/24 Fa0/8

Con 0 Con 0

Switch (2950) 2950(config)#spanning-tree mode rapid-pvst Switch (3560) 3560(config)#spanning-tree mode rapid-pvst Verifying Commands Switch# show spanning-tree vlan 1


BCMSN Lab Manual

- 14 -

ii. MST Diagram

3560 Fa0/23 Fa0/7

2950 Fa0/24 Fa0/8

Con 0 Con 0

Switch (2950) 2950(config)#vlan 10 2950(config-vlan)#name vlan-10 2950(config)#vlan 20 2950(config-vlan)#name vlan-20 2950(config)#vlan 30 2950(config-vlan)#name vlan-30 2950(config)#vlan 40 2950(config-vlan)#name vlan-40 2950(config)#spanning-tree mode mst 2950(config)#spanning-tree mst configuration 2950(config-mst)#name MST-REGION 2950(config-mst)#revision 5 2950(config-mst)#instance 1 vlan 10,20 2950(config-mst)#instance 2 vlan 30,40 2950(config-mst)#show pending Switch (3560) 3560(config)#vlan 10 3560(config-vlan)#name vlan-10 3560(config)#vlan 20

3560(config-vlan)#name vlan-20 3560(config)#vlan 30


BCMSN Lab Manual

- 15 -

3560(config-vlan)#name vlan-30 3560(config)#vlan 40 3560(config-vlan)#name vlan-40 3560(config)#spanning-tree mode mst 3560(config)#spanning-tree mst configuration 3560(config-mst)#name MST-REGION 3560(config-mst)#revision 5 3560(config-mst)#instance 1 vlan 10,20 3560(config-mst)#instance 2 vlan 30,40 3560(config-mst)#show pending 3560(config)#spanning-tree mst 2 priority 0 Verifying Commands Switch#show spanning-tree mst


BCMSN Lab Manual

- 16 -

Lab # 7

1. Inter-VLAN Routing (Router on a Stick)

Objective To transport packets between VLANs by a Router. Diagram

Switch Switch(config)#vlan 10 Switch(config-vlan)#name vlan-10 Switch(config)#vlan 20 Switch(config-vlan)#name vlan-10

Vlan 10 Vlan 20

Host A 10.0.0.1/8 10.0.0.10

Host B 20.0.0.1/8 20.0.0.10

Fa 0/24

Fa 0/1 Fa 0/11

Fa 0 / 0.10 10.0.0.10 / 8

Fa 0 / 0.20 20.0.0.10 / 8

Fa 0/0

2811

2950


BCMSN Lab Manual

- 17 -

Switch(config)#interface range fastEthernet 0/1 - 10 Switch(config-if-range)#switchport mode access Switch(config-if-range)#switchport access vlan 10 Switch(config)#interface range fastEthernet 0/11 - 20 Switch(config-if-range)#switchport mode access Switch(config-if-range)#switchport access vlan 20 Switch(config)#interface fastEthernet 0/24 Switch(config-if)#switchport mode trunk Router Router(config)#interface fastEthernet 0/0 Router(config-if)#no ip address Router(config-if)#no shutdown Router(config)#interface fastEthernet 0/0.10 Router(config-subif)#encapsulation dot1Q 10 Router(config-subif)#ip address 10.0.0.10 255.0.0.0 Router(config-subif)#exit Router(config)#interface fastEthernet 0/0.20 Router(config-subif)#encapsulation dot1Q 20 Router(config-subif)#ip address 20.0.0.10 255.0.0.0 Router(config-subif)#exit Verifying Commands Switch#show vlan Switch#show interface trunk Router#show ip int brief


BCMSN Lab Manual

- 18 -

2. Inter-VLAN Routing (By Multi-layer switch)

Objective To transport packets between VLAN’s by layer 3 switch. Diagram

Fa 0/1 Fa 0/2 10.0.0.10 20.0.0.10

Vlan 10 Vlan 20

Host A Host B 10.0.0.1/8 20.0.0.1/8 10.0.0.10 20.0.0.10

3560

Switch 3560(config)#vlan 10 3560(config-vlan)#name vlan-10 3560(config)#vlan 20 3560(config-vlan)#name vlan-20 3560(config)#interface fastEthernet 0/1 3560(config-if)#switchport mode access 3560(config-if)#switchport access vlan 10 Etronics Solution Provider

BCMSN Lab Manual

- 19 -

3560(config)#interface fastEthernet 0/2 3560(config-if)#switchport mode access 3560(config-if)#switchport access vlan 20 3560(config)#interface vlan 10 3560(config-if)#ip address 10.0.0.10 255.0.0.0 3560(config-if)#no shutdown 3560(config)#interface vlan 20 3560(config-if)#ip address 20.0.0.10 255.0.0.0 3560(config-if)#no shutdown 3560(config)#ip routing Verifying Command Switch#show vlan Switch#show ip route


BCMSN Lab Manual

- 20 -

Lab # 8

Protecting Spanning Tree Protocol Topology

(BPDU Guard, Root-Guard) Objective Tune the spanning tree protocol for protecting the STP topology by using BPDU Guard & Root Guard features.

i. BPDU-Guard (Port) Diagram

Non Root Switch Root Switch Designated Port Root Port

3560 Fa0/23 Fa0/7

2950 Fa0/24

Con 0 Fa0/8 Con 0 Designated Port BPDU-Guard

Enabled port

Switch (3560) 3560(config)#interface fastEthernet 0/8 3560(config-if)#spanning-tree bpduguard enable Etronics Solution Provider

BCMSN Lab Manual

- 21 -

Verifying Commands 3560#show spanning-tree interface fastEthernet 0/8 detail 3560#show interfaces fastEthernet 0/8 status err-disabled

ii. Root-Guard Diagram

3560 Root Switch

Root-Guard Fa0/8 Enabled port

Fa0/24

Non Root Switch

2950 Switch (3560) 3560(config)#spanning-tree vlan 1 priority 0 3560(config)#interface fastEthernet 0/8 3560(config-if)#spanning-tree guard root Switch (2950) 2950(config)#spanning-tree vlan 1 priority 0 Verifying Commands 3560#show running-config interface fastEthernet 0/8 Switch#show spanning-tree vlan 1


BCMSN Lab Manual

- 22 -

Lab # 9

Ether Channel Objective Ether Channel allows to specify the multiple Ethernet ports of the same type as a single virtual link. Lab Objective :

1. Enable Ether-Channel with no protocol on Cisco catalyst switches. 2. Enable Ether-Channel (PAgP) on Cisco catalyst switches. 3. Enable Ether-Channel (LACP) on Cisco catalyst switches.

i. Ether-Channel

Diagram

Ether Channel 3560

Switch (2950) 2950(config)#interface range fastEthernet 0/23 - 24 2950(config-if-range)#channel-group 1 mode on Switch (3560) 3560(config)#interface range fastEthernet 0/7 - 8 3560(config-if-range)#channel-group 1 mode on

Root Switch Non Root

Switch

2950 Fa0/23

Fa0/24 Fa0/8

Fa0/7


BCMSN Lab Manual

- 23 -

Verifying Commands Switch#show etherchannel Switch#show etherchannel protocol Switch#show etherchannel port Switch#show etherchannel port-channel Switch#show etherchannel summary

ii. Ether-Channel (PAgP) Diagram

Ether Channel 3560

Switch (2950) 2950(config)#interface range fastEthernet 0/23 - 24 2950(config-if-range)#channel-group 1 mode desirable Switch (3560) 3560(config)#interface range fastEthernet 0/7 - 8 3560(config-if-range)#channel-group 1 mode auto Verifying Commands Switch#show etherchannel Switch#show etherchannel protocol


Switch

2950 Fa0/23

Fa0/24 Fa0/8

Fa0/7


BCMSN Lab Manual

- 24 -

Switch#show etherchannel port Switch#show etherchannel port-channel Switch#show etherchannel summary

iii. Ether-Channel (LACP) Diagram

Ether Channel 3560

Switch (2950) 2950(config)#interface range fastEthernet 0/23 - 24 2950(config-if-range)#channel-group 1 mode active Switch (3560) 3560(config)#interface range fastEthernet 0/7 - 8 3560(config-if-range)#channel-group 1 mode passive Verifying Commands Switch#show etherchannel Switch#show etherchannel protocol Switch#show etherchannel port Switch#show etherchannel port-channel Switch#show etherchannel summary


Switch

2950 Fa0/23

Fa0/24 Fa0/8

Fa0/7


BCMSN Lab Manual

- 25 -

Lab#10

Hot Standby Router Protocol

(HSRP) Objective Understanding the Layer 3 device redundancy.

Diagram

Virtual Router

10.0.0.20

L0 15.0.0.1

L0 15.0.0.1

E0 10.0.0.5 S0 13.0.0.1 S0 13.0.0.2 RA ISP-1

HSRP

S0 14.0.0.1

RB ISP-2 S0 14.0.0.2

E0 10.0.0.10

GROUP 64

Host A 10.0.0.1


BCMSN Lab Manual

- 26 -

Router A RouterA(config)# interface ethernet0 RouterA(config-if)# ip address 10.0.0.5 255.0.0.0 RouterA(config-if)# standby 64 ip 10.0.0.20 RouterA(config-if)# standby 64 priority 150 RouterA(config-if)# standby 64 preempt RouterA(config-if)# standby 64 track serial 0 100 Router B RouterB(config)# interface ethernet0 RouterB(config-if)# ip address 10.0.0.10 255.0.0.0 RouterB(config-if)# standby 64 ip 10.0.0.20 RouterB(config-if)# standby 64 preempt RouterB(config-if)# standby 64 track serial 0 50 Verifying Commands Router# debug standby Router# show standby


BCMSN Lab Manual

- 27 -

Lab # 11

VLAN ACL Objective The VLAN ACL’s are filters that can directly affect how packets are handled within a VLAN. Diagram

3560

Fa/1 Fa/2 VLAN 2 VLAN 2

Switch (3560) 3560(config)#vlan 2 3560(config-vlan)#name vlan-2 3560(config)#interface range fastEthernet 0/1 - 2 3560(config-if-range)#switchport mode access 3560(config-if-range)#switchport access vlan 2

www & ftp Server

Host B Host A Ip Add: 10.0.0.2 Ip Add: 10.0.0.1


BCMSN Lab Manual

- 28 -

3560(config)#access-list 110 permit tcp host 10.0.0.2 host 10.0.0.1 eq www 3560(config)#access-list 110 permit tcp host 10.0.0.2 host 10.0.0.1 eq ftp 3560(config)#vlan access-map VLAN-ACL 10 3560(config-access-map)#match ip address 110 3560(config-access-map)#action drop 3560(config)#vlan access-map VLAN-ACL 20 3560(config-access-map)#action forward 3560(config)#vlan filter VLAN-ACL vlan-list 2 Verifying Commands 3560#show access-lists 3560#show vlan access-map VLAN-ACL 3560#show vlan filter vlan 2 3560#show vlan filter access-map VLAN-ACL


BCMSN Lab Manual

- 29 -

Lab # 12

Private Vlan Objective Understanding the Private VLAN operation. Diagram

Fa0/1 10.0.0.20

Fa0/0 20.0.0.10

Primary Vlan 100

Fa0/10

Promiscuous 2811Web Server

Fa0/3 20.0.0.1 Fa0/1 Fa0/2

Isolated Community

Vlan 20 Vlan 10

10.0.0.3 10.0.0.20

10.0.0.1 10.0.0.210.0.0.20 10.0.0.20

Switch (3560) Switch(config)#vtp mode transparent Switch(config)#vlan 10 Switch(config-vlan)#private-vlan community Switch(config)#vlan 20 Switch(config-vlan)#private-vlan isolated


BCMSN Lab Manual

- 30 -

Switch(config)#vlan 100 Switch(config-vlan)#private-vlan primary Switch(config-vlan)#private-vlan association 10,20 Switch(config)#int range fastEthernet 0/1 - 2 Switch(config-if-range)#switchport mode private-vlan host Switch(config-if-range)#switchport private-vlan host-association 100 10 Switch(config)#int fa0/3 Switch(config-if)#switchport mode private-vlan host Switch(config-if)#switchport private-vlan host-association 100 20 Switch(config)#int fa0/10 Switch(config-if)#switchport mode private-vlan promiscuous Switch(config-if)#switchport private-vlan mapping 100 10,20 Verifying Commands Switch#show vlan private-vlan Switch# show vlan private-vlan type


BCMSN Lab Manual

- 31 -

Lab # 13

Port Security

Objective To demonstrates the concept of port security mechanism on Switch. Diagram

2950-SW

Fastethernet 0 / 9

Secure MAC Address 0011.d8b5.4126

Switch (2950) Switch(config)#int fa0/9 Switch(config-if)#switchport mode access Switch(config-if)#switchport port-security Switch(config-if)#switchport port-security maximum 1 Switch(config-if)#switchport port-security mac-address sticky Switch(config-if)#switchport port-security violation shutdown Verifying Commands Switch#show mac-address-table


BCMSN Lab Manual

- 32 -

Switch#show port-security Switch#show port-security interface fa0/9 Switch#show interface status err-disabled


BCMSN Lab Manual

- 33 -

Lab # 14 (A)

Wireless Infrastructure Mode Using Cisco Aironet Access Point

Objective This lab includes Infrastructure implementation of Wireless. Diagram

Cisco Aironet AP 1130

IP: 192.168.1.150 /24

PoE

Cisco Catalyst 3560

Wireless Client 2 Wireless Client 1 IP: 192.168.1.170 / 24 IP: 192.168.1.160 /24

SSID: esp


BCMSN Lab Manual

- 34 -

Configuration Step 1: Accessing the AP.

• Connect a Pc (having ip address 192.168.1.160 255.255.255.0) to the same PoE enabled switch, to which AP is already connected.

• Verify connectivity by ping to default ip address (192.168.1.150) of AP.

• Open Internet explorer and type the AP default ip address (192.168.1.150).

• Enter;

o Username: ap o Password: Cisco

• The home page of AP appears as shown below.


BCMSN Lab Manual

- 35 -

Step 2: Click on Radio0-802.11G interface.


BCMSN Lab Manual

- 36 -

Step 3: Go to the ‘SETTINGS’ tab and select ‘Enable’ in the ‘Enable Radio’ option & press ‘Apply’.

Step 4: Go to ‘EXPRESS SECURITY’ and type an SSID ( esp ) and select the check box ‘Broad SSID in Beacons’ & press ‘Apply’.


BCMSN Lab Manual

- 37 -

Step 5: Open Aironet Desktop Utility on the wireless client 1.

Step 6: Go to ‘Profile Management’ tab and click ‘Scan’.


BCMSN Lab Manual

- 38 -

Step 7: Verify the SSID (esp) appears as follow. Select it and press ‘Activate’.

Step 8: Now create a profile as shown below.


BCMSN Lab Manual

- 39 -

Step 9a: Verify that a blue circle appears on antenna symbol under ‘Network Name (SSID)’.

Step 9b: Verify the connectivity under ‘Current Status’ tab.


BCMSN Lab Manual

- 40 -

Step 10: Verify association of wireless client 1 with AP in the ASSOCIATION option.

Step 11: On wireless client 2, open wireless desktop utility. No association appears for some time.


BCMSN Lab Manual

- 41 -

Step 12: Go to ‘Site Survey’ tab and see the SSID (esp) as shown below. Select it and press ‘Connect’.

Step 13: Verify that wireless client 2 is also connected to Ap.


BCMSN Lab Manual

- 42 -

Step 14: Verify association of wireless client 2 with AP in the ASSOCIATION option.


BCMSN Lab Manual

- 43 -

Lab # 14 (B)

Wireless Adhoc Mode Objective This lab includes Adhoc implementation of Wireless Lan. Diagram

Wireless Client 1

SSID: esp-adhoc

Wireless Client 2 IP: 10.0.0.44/ 8 IP: 10.0.0.33/ 8


BCMSN Lab Manual

- 44 -

Configuration

Step 1: On wireless client 1, open wireless desktop utility. Go to ‘Profile’ tab and click ‘New’.

Step 2: Enter a profile name and Press ‘OK’.


BCMSN Lab Manual

- 45 -

Step 3: Here you can see available networks. Click ‘Manual Setup’.

Step 4: Enter the ip address and subnet mask as shown below. Click ‘Next’.


BCMSN Lab Manual

- 46 -

Step 5: Select Wireless Mode as ‘Ad-Hoc Mode’. Enter SSID (esp-adhoc) and click Next.

Step 6: Select Channel and Network Mode as shown below and click Next.


BCMSN Lab Manual

- 47 -

Step 7: Select ‘Disabled’ in Security option and click Next.

Step 8: Verify all configurations and click Save.


BCMSN Lab Manual

- 48 -

Step 9: Profile configuration has been completed. Press ‘Connect to Network’.

Step 10: Verify that wireless client 1 has successfully joined Ad-Hoc network.


BCMSN Lab Manual

- 49 -

Step 11: Open Aironet Desktop Utility on the wireless client 2.


BCMSN Lab Manual

- 50 -

Step 12: Go to ‘Profile Management’ tab and click ‘Scan’.

Step 13: Verify the SSID (esp-adhoc) appears as follow. Select it and press ‘Activate’.


BCMSN Lab Manual

- 51 -

Step 14: Now create a profile as shown below. Press ‘OK’.

Step 15: Verify the connectivity under ‘Current Status’ tab.


BCMSN Lab Manual

- 52 -

Lab # 15

Configuring Cisco IP Telephony Using Cisco Call Manager & Cisco IP Phones

Objective

Establishing VoIP call using Cisco Call Manager & Cisco IP Phones: 7940 & 7971.

Cisco Call Manager

Client 1 Client 2 Cisco 7940 Cisco 7971 IP Phone IP Phone


Bcmsn lab manual v4

Documents

Transcript of Bcmsn lab manual v4