AVR 3650, AVR 365 AVR 2650, AVR 265 - GfK .AVR 3650, AVR 365 AVR 2650, AVR 265...
Embed Size (px)
Transcript of AVR 3650, AVR 365 AVR 2650, AVR 265 - GfK .AVR 3650, AVR 365 AVR 2650, AVR 265...
AVR 3650, AVR 365 AVR 2650, AVR 265
Table of ContentsINTRODUCTION 3
SUPPLIED ACCESSORIES 3
IMPORTANT SAFETY INFORMATION 3
PLACE THE RECEIVER 3
FRONT-PANEL CONTROLS 4
REAR-PANEL CONNECTORS 6
SYSTEM REMOTE CONTROL FUNCTIONS 8
ZONE 2 REMOTE CONTROL FUNCTIONS (AVR 3650/AVR 365 ONLY) 10
INTRODUCTION TO HOME THEATER 12
TYPICAL HOME THEATER SYSTEM 12
MULTICHANNEL AUDIO 12
SURROUND MODES 12
PLACE YOUR SPEAKERS 13
PLACING THE LEFT, CENTER AND RIGHT SPEAKERS 13
PLACING THE SURROUND SPEAKERS IN A 5.1-CHANNEL SYSTEM 13
PLACING THE SURROUND SPEAKERS IN A 7.1-CHANNEL SYSTEM 13
PLACING FRONT HEIGHT SPEAKERS IN A 7.1-CHANNEL SYSTEM 13
PLACING THE SUBWOOFER 13
TYPES OF HOME THEATER SYSTEM CONNECTIONS 14
SPEAKER CONNECTIONS 14
SUBWOOFER CONNECTIONS 14
SOURCE DEVICE CONNECTIONS 14
VIDEO CONNECTIONS 15
RADIO CONNECTIONS 16
NETWORK CONNECTOR 16
USB PORT 16
RS-232 CONNECTOR 16
MAKING CONNECTIONS 17
CONNECT YOUR SPEAKERS 17
CONNECT YOUR SUBWOOFER 17
CONNECT YOUR TV OR VIDEO DISPLAY 17
CONNECT YOUR AUDIO AND VIDEO SOURCE DEVICES 18
CONNECT THE BRIDGE IIIP 20
CONNECT TO YOUR HOME NETWORK 20
CONNECT THE RADIO ANTENNAS 20
INSTALL A MULTIZONE SYSTEM 21
CONNECT IR EQUIPMENT (AVR 3650/AVR 365 ONLY) 22
CONNECT THE 12V TRIGGER OUTPUT 23
CONNECT TO AC POWER 23
SET UP THE REMOTE CONTROL 23
INSTALL THE BATTERIES IN THE REMOTE CONTROL 23
PROGRAM THE REMOTE TO CONTROL YOUR SOURCE DEVICES AND TV 23
SET UP THE AVR 25
TURN ON THE AVR 25
USING THE ON-SCREEN MENU SYSTEM 25
CONFIGURE THE AVR FOR YOUR SPEAKERS 25
SET UP YOUR SOURCES 26
SET UP THE NETWORK 27
OPERATING YOUR AVR 28
CONTROLLING THE VOLUME 28
MUTING THE SOUND 28
DOLBY VOLUME 28
LISTENING THROUGH HEADPHONES 28
SELECTING A SOURCE 28
LISTENING TO FM AND AM RADIO 29
LISTENING TO SIRIUS SATELLITE RADIO 29
LISTENING TO MEDIA ON A USB DEVICE (AVR 3650/AVR 365) 30
LISTENING TO AN iPod/iPhone DEVICE 30
LISTENING TO INTERNET RADIO 31
LISTENING TO MEDIA VIA YOUR HOME NETWORK 32
SELECTING A SURROUND MODE 32
AUDIO EFFECTS 32
VIDEO MODES 32
ADVANCED FUNCTIONS 33
AUDIO PROCESSING AND SURROUND SOUND 33
VIDEO PROCESSING 34
MANUAL SPEAKER SETUP 36
LISTENING IN ZONE 2 39
SYSTEM SETTINGS 39
SETTINGS LOCK 40
ADVANCED REMOTE CONTROL PROGRAMMING 41
SLEEP TIMER 41
RESETTING THE REMOTE 42
PROCESSOR RESET 42
Introduction, Supplied Accessories, Important Safety Information and Place the Receiver
Thank you for choosing this Harman Kardon product!
For more than fifty years, the Harman Kardon mission has been to share a passion for music and entertainment, using leading-edge technology to achieve premium performance. Sidney Harman and Bernard Kardon invented the receiver, a single component designed to simplify home entertainment without compromising performance. Over the years, Harman Kardon products have become easier to use, while offering more features and sounding better than ever.
The AVR 3650, AVR 2650, AVR 365 and AVR 265 7.1-channel digital audio/video receivers continue this tradition with some of the most advanced audio and video processing capabilities yet, and a wealth of listening and viewing options.
To obtain the maximum enjoyment from your new receiver, please read this manual and refer back to it as you become more familiar with its features and their operation.
If you have any questions about this product, its installation or its operation, please contact your Harman Kardon retailer or custom installer, or visit the Web site at www.harmankardon.com.
The following accessory items are supplied with your receiver. If any of these items are missing, please contact your Harman Kardon dealer or Harman Kardon customer service at www.harmankardon.com.
System remote control
Zone 2 remote control (AVR 3650/AVR 365 only)
AM loop antenna
FM wire antenna
Six AAA batteries (AVR 3650/AVR 365); four AAA batteries (AVR 2650/AVR 265)
AC power cord
IMPORTANT SAFETY INFORMATION
Verify Line Voltage Before Use
The AVR 3650 and AVR 2650 have been designed for use with 120-volt AC current. The AVR 365 and AVR 265 have been designed for use with 220 240-volt AC current. Connection to a line voltage other than that for which your receiver is intended can create a safety and fire hazard and may damage the unit. If you have any questions about the voltage requirements for your specific model, or about the line voltage in your area, contact your selling dealer before plugging the unit into a wall outlet.
Do Not Use Extension Cords
To avoid safety hazards, use only the power cord supplied with your unit. We do not recommend that extension cords be used with this product. As with all electrical devices, do not run power cords under rugs or carpets, or place heavy objects on them. Damaged power cords should be replaced immediately by an authorized service center with a cord meeting factory specifications.
Handle the AC Power Cord Gently
When disconnecting the power cord from an AC outlet, always pull the plug; never pull the cord. If you do not intend to use your receiver for any considerable length of time, disconnect the plug from the AC outlet.
Do Not Open the Cabinet
There are no user-serviceable components inside this product. Opening the cabinet may present a shock hazard, and any modification to the product will void your warranty. If water or any metal object such as a paper clip, wire or staple accidentally falls inside the unit, disconnect it from the AC power source immediately, and consult an authorized service center.
CATV or Antenna Grounding (AVR 3650/AVR 2650)
If an outside antenna or cable system is connected to this product, be certain that it is grounded so as to provide some protection against voltage surges and static charges. Section 810 of the United States National Electrical Code, ANSI/NFPA No. 70-1984, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements of the grounding electrode.
NOTE TO CATV SYSTEM INSTALLER: This reminder is provided to call the CATV (cable TV) system installers attention to article 820-40 of the NEC, which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as possible.
Place the Receiver
Place the receiver on a firm and level surface. Be certain that the surface and any mounting hardware can support the AVRs weight.
Provide proper space above and below the receiver for ventilation. If you install the receiver in a cabinet or other enclosed area, provide cooling air within the cabinet. Under some circumstances, a fan may be required.
Do not obstruct the ventilation slots on the top of the receiver or place objects directly over them.
Do not place the receiver directly on a carpeted surface.
Do not place the receiver in moist or humid locations, in extremely hot or cold locations, in areas near heaters or heat registers, or in direct sunlight.
HDMI FrontInput Connector
Headphone Jack/EzSet/EQMic Input
Continued on next page
Video Modes Button
Headphone Jack/ EzSet/EQ Mic Input
Audio Effects Button
Surround Modes Button
HDMI Front Input Connector
Source List Button
AVR Front-Panel Controls, continued
Power Indicator: This LED has three possible modes:
LED is off: Indicates that the AVR is unplugged or the rear-panel Main Power switch is off.
LED glows amber: Indicates that the AVR is in the Standby mode.
LED glows white: Indicates that the AVR is turned on.
IMPORTANT NOTE: If the PROTECT message ever appears on the AVRs front-panel message display, turn off the AVR and unplug it from the AC outlet. Check all speaker wires for a possible short-circuit (the + and conductors touching each other or both touching the same piece of metal). If a short-circuit is not found, bring the unit to an authorized Harman Kardon service center for inspection and repair before using it again.
Power button: Press this button to turn the receiver on or to place it in the Standby mode.
Setup button: Press this button to access the AVRs main menu.
Info button: Press this button to access the AVRs Source submenu, which contains the settings for the source currently playing