Avionica – Powering Secure Data and Communication Solutions

U.S. Department of Transpo1tation

Federal Aviation Administration

September 26, 201 7

A vionica, Inc. Attn: Jim Mora 9941 West Jessamine Street Miami, Florida 33 15 7

Aircraft Certification Service System Oversight Division Orlando MIDO Section 5950 Haze ltine National Dr. , Suite 405 Orlando, FL 32822

Phone: (407) 855-9050

FEDERAL A VIA TI ON ADMINISTRATION - PARTS MANUFACTURER APPROVAL

Dear Mr. Mora:

In accordance with the provisions of Title 14, Code of Federal Regulations (14 CFR), part 21, Certification Procedures for Products, Articles, and Parts, subpaii K, the Federal Aviation Administration (FAA) has found that the design data, based on Licensing Agreement submitted by Archeion Holdings, LLC., with your letter dated August 31 , 2017 meet the airworthiness requirements of the regulations applicable to the products on which the articles are to be installed. Additionally, the FAA has determined that Avionica, Inc. has established the quality system required by § 21.307 at 9941 West Jessamine Street, Miami, FL 33157. Accordingly, Parts Manufacturer Approval (PMA) is hereby granted for production of the replacement articles listed in the enclosed Supplement No. 43.

You are reminded that the provisions of 14 CFR, parts 21 and 45 , apply to the enclosed PMA Listing-Supplement No.43. The enclosed supplement should be retained with the original PMA letter as evidence of approval to produce the aiiicles concerned.

Sincerely,

V John Kolin /" Manager, Orlando MIDO

Enclosure PMA Listing Supplement No. 43

U.S. Department of Transportation


FEDERAL AVIATION ADMINISTRATION -PARTS MANUFACTURER APPROVAL

A vionica, Inc. 9941 West Jessamine Street Miami, Florida 33 157

Article Name

avWiFi , Wireless Router, 802. 11 alb/gin, No SSD

Part Number

650-0500-00

Approved Replacement for Pait Number

Modification Patt

Approva l Basis and Approved Design Data

ldenticality per 14 CFR §2 1.303 , per li censing agreement between Archeion Holdings, LLC and Avionica, Inc. to use Supp lement Type Cert ificate (STC) ST03967 AT, issued September 18, 20 15, and last amended June 22, 2017 Archeion Holdings LLC. Master Drawing List DWG No. 120890-MDL,

Dated June 4, 20 l7 or later FAA approved revision , with Approved Model List No. 120890-AML, Rev B Dated June 22, 2017, or later FAA approved revision, with 120890-MKL, Rev M dated June 14, 2017, or later FAA approved revision .

Page I of6

PMA Project No. POI 734CE Supplement No. 43 Date: Sep 26, 2017

MAKE Eligibili ty:

Boeing

MODEL Eligibi lity:

B777-200/-300

B737-300/-400/-700/-800

B767-200/-300/-300F/-400ER

DC-10, MD-10, MD-11

B747-l 00/-200/-300/-400/-SP/-8/-SF/SR


A vionica, Inc. 9941 West Jessamine Street Miami, Florida 33157

Pait Name

avWiFi , Wireless Router, 802.11 alb/gin, 32G SSD

Part Number

650-0500-0 I

avWiFi , Wireless 650-0500-02 Router, 802 .11 alb/gin, 64G SSD

Approved Rep lacement for Part Number

Modification Part

FAA Approval Basis and Approved Design Data

Identicality per 14 CFR §2 1.303, per licensing agreement between Archeion Holdings, LLC and Avionica, Inc. to use Supplement Type Certificate (STC) ST03967AT, issued September 18, 2015, and last amended June 22, 2017 Archeion Holdings LLC. Master Drawing List DWG No . 120890-MDL, RevN Dated June 4, 2017 or later FAA approved revision , with Approved Model List No. 120890-AML, Rev B Dated June 22, 2017, or later FAA approved revision , with 120890-MKL, Rev M dated June 14, 20 17, or later FAA approved revision.

PMA Project No. PQl 734CE Supplement No. 43 Date: Sep 26, 2017

Installation Eligibility: MAKE

Boeing

Installation Eligibility: MODEL

B777-200/-300

8737-300/-400/-700/-800

B767-200/-300/-300F/-400ER

DC-10, MD-10, MDII

B74 7-100/-200/-300/-400/-SP/-8/-8F/SR

Modification ldenticality per 14 CFR Boeing 8777-200/-300 Part §2 1.303, per li censing

agreement between Archeion Ho ldings, LLC and Avionica, Inc. to use Supplement Type Certificate (STC) ST03967 AT, issued September 18, 2015 , and last amended June 22, 2017 Archeion Holdings LLC. Master Drawing List DWG No. 120890-MDL, RevN Dated June 4, 2017 or later FAA approved revision , with Approved Model List No. 120890-AML, Rev B Dated June 22, 2017, or later FAA approved revision , with 120890-MKL, Rev M dated June 14, 2017, or later FAA approved revision.

Page 2 of6

B737-300/-400/-700/-800

B767-200/-300/-300F/-400ER

DC-10, MD-10, MD-11

8747-100/-200/-300/-400/-SP/-8/-8F/SR



Pait Name

avW iFi , Wireless Router, 802.11 a/b/g/n, 128G SSD

Part Number

650-0500-03

avWiFi, Wireless 650-0500-04 Router, 802. 11 alb/gin, 256G SSD

Approved Replacement for Part Number

Modification Pait

Modification Part


ldenticality per 14 CFR §21.303 , per licensing agreement between Archeion Holdings, LLC and A vionica, Inc. to use Supp lement Type Certificate (STC) ST03967 AT, issued September 18, 2015 , and last amended June 22, 20 17 Archeion Holdings LLC. Master Drawing List DWG No. 120890-MDL, RevN Dated June 4, 2017 or later FAA approved revision, with Approved Model List No. 120890-AML, Rev B Dated June 22, 20 17, or later FAA approved revision , with 120890-MKL, Rev M dated June 14, 2017, or later FAA approved revision.

ldentica li ty per 14 CFR §21 .303 , per li censing agreement between Archeion Holdings, LLC and Avionica, Inc. to use Supp lement Type Certificate (STC) ST03967 AT, issued September 18, 2015 , and last amended June 22, 2017 Archeion Holdings LLC. Master Drawing List DWG No. 120890-MDL, RevN Dated June 4, 2017 or later FAA approved revision, with Approved Model List No. 120890-AML, Rev 8 Dated June 22, 20 17, or later FAA approved revision, with 120890-MKL, Rev M dated June 14, 20 17, or later FAA approved revision.

Page 3 of6



Boeing

Boeing


B777-200/-300

B737-300/-400/-700/-800

B767-200/-300/-300F/-400ER

DC-10, MD-10, MDI 1

8747-100/-200/-300/-400/-SP/-8/-8F/SR

B777-200/-300

B737-300/-400/-700/-800

B767-200/-300/-300F/-400ER

DC-10, MD-10, MD-11

8747-100/-200/-300/-400/-SP/-8/-8F/SR



Pait Name

avWiFi Installation (Short Shelf) Kit

avWiFi Installation (Long Shelf) Kit

Part Number

120890K-1

l20890K-2


Modification Part

Modification Part


Identical ity per 14 CFR §21.303 , per licensing agreement between Archeion Holdings, LLC and Avionica, Inc. to use Supplement Type Certificate (STC) ST03967 AT, issued September 18, 2015, and last amended June 22, 2017 Archeion Holdings LLC. Master Drawing List DWG No. 120890-MDL, RevN Dated June 4, 2017 or later FAA approved revision, with Approved Model List No. 120890-AML, Rev B Dated June 22, 2017, or later FAA approved revision, with 120890-MKL, Rev M dated June 14, 2017, or later FAA approved revision.

Identicality per 14 CFR §21.303 , per licensing agreement between Archeion Holdings, LLC and Avionica, Inc. to use Supplement Type Certificate (STC) ST03967 AT, issued September 18, 2015, and last amendedJune22,2017 Archeion Holdings LLC. Master Drawing List DWG No . 120890-MDL, RevN Dated June 4, 2017 or later FAA approved revision, with Approved Model List No. 120890-AML, RevB Dated June 22, 2017, or later FAA approved revision, with 120890-MKL, Rev M dated June 14, 2017, or later FAA approved revision.

Page 4 of6



Boeing

Boeing

lnstal lation Eligibi lity: MODEL

8777-200/-300

8737-300/-400/-700/-800

B767-200/-300/-300F/-400ER

DC-10, MD-10, MD-11

8747-100/-200/-300/-400/-SP/-8/-8F/SR

8777-200/-300

8737-300/-400/-700/-800

B767-200/-300/-300F/-400ER

DC-10, MD-10, MD-1 I

874 7-100/-200/-300/-400/-SP/-8/-8F/SR


Avionica, Inc. 9941 West Jessamine Street Miami, Florida 33 157

Part Name

avWiFi Install ation (Stand-Alone) K it

Part Number

120890K-3

Approved Replacement for Pat1 Number

Modification Part


Identica lity per 14 CFR §2 1.303 , per li censing agreement between Archeion Ho ldings, LLC and Avionica, Inc. to use Supplement Type Ce1tificate (STC) ST03967 AT, issued September 18, 20 15, and last amended June 22, 20 J 7 Archeion Holdings LLC. Master Drawing List DWG No. 120890-MDL, RevN Dated June 4, 2017 or later FAA approved revision , with Approved Model L ist No. 120890-AML, RevB Dated June 22, 2017, or later FAA approved revision, with 120890-MKL, Rev M dated June 14, 20 17, or later FAA approved revis ion.

Page 5 of6


Insta llat ion Eligibility: MAKE

Boeing


B777-200/-300

B737-300/-400/-700/-800

B767-200/-300/-300F/-400ER

DC-10, MD- I 0, MD-11

B74 7-100/-200/-300/-400/-SP/-8/-8F/SR

FEDERAL AVIATION ADMINISTRATION-PARTS MANUFACTURER APPROVAL


Part Name Part Number

Approved Replacement for Patt Number





-----------------------------End Of Listing----------------------

Note: The procedures that have been accepted by the type certificate or TSO authorization holder and its cognizant FAA Aircraft Certification Office, for minor changes to original articles used on type-certificated products, are also acceptable for incorporating the same minor changes on identical PMA replacement articles The PMA holder must be able to show traceabihty relating to the TC, STC, or TSO authorization holder on all minor changes incorporated by this procedure When these procedures are no longer applicable because of completion of the production contract, or tennination of the licensing agreement or business relationship, all subsequent minor design changes to the PMA atticles must be submitted in a manner as determined by the ACO Major design changes (reference 14 CFR §§21319 and 21 619) to drawings and specifications are to be handled in the same manner as that for an original PMA.

John C. Kolin Manager, Orlando MIDO

Page6of6

U.S. Department of Transportation

Federal Avia tion Adm in ist ra t ion

October 25, 2017

Avionica, Inc. Attn: Jim Mora 9941 West Jessamine Street Miami, Florida 33157

Aircra ft Certification Service System Oversight Division Orlando MIDO Section 5950 Hazeltine 1ational Dr.. Suite 405 Orlando. FL 32822

Phone: ( 407) 855-9050

FEDERAL AV IATION ADMIN ISTRAT ION - PARTS MANUFACTURER APPROVAL

Dear Mr. Mora:

ln accordance with the provisions of Title 14. Code off ederal Regulations ( l 4 CFR), part 21. Certification Procedures for Products, Articles, and Parts. subpart K. the Federal Aviation Administration (FAA) has found that the design data, based on Licensing Agreement submitted by Archeion Holdings, LLC., with your letter dated September 19, 20 17 meet the airworthiness requirements of the regulations applicable to the products on which the articles arc to be installed. Additionally, the FAA has determined that Avionica, Inc. has established the quality system required by§ 21.307 at 9941 West Jessamine Street, Miami , FL 33157. Accordingly. Parts Manufacturer Approval (PMA) is hereby granted for production of the rep lacement articles listed in the enclosed Supplement No. 44.

You are reminded that the provisions of 14 CFR. parts 21 and 45, apply to the enclosed PMA Listing-Supplement No.44. The enclosed supplement should be retained with the original PMA letter as evidence or approval to produce the articles concerned.

Sincerely.

/

t>,.L.lohn Kolin Manager, Orland

Enclosure PMA Listing Supplement No. 44

U.S. Deportment of Transportation


FEDERAL AVIATION ADM INISTRATION - PARTS MANUFACTURER APPROVAL

A vionica. Inc. 9941 West Jessamine Street Miami, Florida 33 157

Article ame

satLI NK MAX Router. o Iridium, GPS. 739/741 lntergration

satLINK MAX Router. Single Iridium. GPS. 739/741 I ntergration

Part Number

804-0520-30

804-0520-3 I

Approved Replacement for Part

umber

Modification Part

Modification Part

Approval Basis and Approved Design Data

ldenticali ry per 14 CFR §21 .303. per licensing agreement between Archeion Holdings. LLC and A vionica, Inc. to use Supplement Type Certificate (STC) ST04375AT, issued June 27, 20 17. Archeion Holdings LLC. Master Drawing List DWG No. 160910-MDL, Rev A Dated June 12. 2017 or later FAA approved revision, with 130710-MKL, Rev J dated June 4, 20 17, or later FAA approved revision.

ldenticality per 14 CFR §2 1.303. per licensing agreement between Archeion Holdings, LLC and A vionica, Inc. to use Supplement Type Certificate (STC) ST04375AT, issued June 27, 20 17, Archeion Holdings LLC. Master Drawing List DWG o. 160910-MDL. Rev A Dated June 12, 20 17 or later FAA approved revision, with 130710-MKL, Rev J dated June4, 20 17, or later FAA approved revision.

Page I of7

PMA Project No. POI 734CE Supplement No. 44 Date: Oct 25, 2017

MAKE Eligibiliry:

Boeing

Boeing

MODEL Eligibility:

B747-I 00/-200/-300/-400/SP/SR/-8/-SF

series

B74 7- 100/-200/-300/-400/SP/SR/-8/-SF

series

FEDERAL AVIATION ADMINISTRATION-PARTS MANUFACTURER APPROVAL

A vionica, Inc. 9941 West Jessamine Street Miami. Florida33157 (786) 544-1100

Part Name

satLINK MAX Router, Dual Iridium. GPS, 739174 1 lntergration

satLIN K MAX Router, Triple Iridium, GPS. 739/74 I lntergration

Part Number

804-0520-32

804-0520-33


Modification Part

Mod ification Part


ldenticality per 14 CF R §21.303, per licensing agreement between Archeion Holdings. LLC and Avionica. Inc. to use Supplement Type Certificate (STC) ST04375AT, issued June 27, 20 I 7. Archeion Holdings LLC. Master Drawing List DWG No. 160910-MDL, Rev A Dated June I 2. 2017 or later FAA approved revision, with 1307 10-MKL, Rev J dated June 4. 2017. or later FAA approved revision.

ldentical ity per 14 CFR §2 1.303. per licensing agreement between Archeion Holdings, LLC and Avionica, Inc. to use Supplement Type Certificate (STC) ST04375AT, issued June 27. 20 I 7, Archeion Holdings LLC. Master Drawing List DWG o. 160910-MDL. Rev A Dated June 12, 2017 or later FAA approved revision. with 130710-MKL, Rev J dated June 4, 20 17, or later FAA approved revision .

Page 2 of7

PMA Project No. PQl 734CE Supplement No. 44

Date: month day, year


Boeing

Boeing

Installation El igibility: MODEL

6747-100/-200/-300/-400/SP/SR/-8/-8F

series

8 74 7- 100/-200/-300/-400/SP/SR/-8/-8F

series

FEDERAL AVIATION ADMINISTRATION - PARTS MANUFACTURER APPROVAL

Avionica, Inc. 9941 West Jessamine Street Miami , Florida 33 157 (786) 544-1100

Part Name

satLI K MAX Router, Quad Iridium, GPS, 7391741 I ntergration

Part Number

80-t-0520-34

avRDC MAX, No 804- 1250-30

Audio Channel. ARTNC 429. RS422, ARJNC 717, Ethernet. 28Ydc


Modification Part

Modification Part


Jdenticality per 14 CFR §2 1.303, per licensing agreement between Archcion I loldings. LLC and Avionica. Inc. to use Supplement Type Certificate (STC) ST04375AT, issued June 27, 2017, Archeion Holdings LLC. Master Drawing List DWG No. 160910-MDL, Rev A Dated June 12, 2017 or later FAA approved revision. with 130710-MKL, Rev J dated June 4, 20 17, or later FAA approved revision.

ldenticality per 14 CFR §2 1.303, per licensing agreement between Archeion Holdings, LLC and A vionica, Inc. to use Supplement Type Certificate (STC) ST04375AT, issued June 27, 20 17, Archeion Holdings LLC. Master Drawing List DWG No. 160910-MDL. Rev A Dated June 12, 2017 or later FAA approved revision, with 130710-MKL. Rev J dated June 4. 2017. or later FAA approved revision.

Page 3 of7

PMA Project o. PO 1734CE Supplement No. 44


Installation Eligibility: MAK E

Boeing

Boeing


8747-1 00/-200/-300/-400/SP/SR/-8/-8F

series

874 7-100/-200/-300/-400/SP/SR/-8/-8F

series


A vionica. Inc. 9941 West Jessamine Street Miami. Florida 33157 (786) 544-1I00

Part Name

avRDC MAX. Single Audio Channel, ARINC 429. RS422, ARl C 717. Ethernet. 28Vdc

avRDC MAX. Dual Audio Channel, ARfNC 429, RS422, ARJNC 717. Ethernet. 28Vdc

Part Number

80-l-1 250-31

804-1250-32


Modification Part

Modification Part

FA A Approval Basis and Approved Design Data

ldenticality per 14 CFR §21.303, per licensing agreement between Arche ion Holdings, LLC and A vionica. Inc. to use Supplement Type Certificate (STC) ST04375AT, issued June 27, 20 17, Archeion Holdings LLC. Master Drawing List DWG No. 160910-MDL. Rev A Dated June 12. 20 17 or later FAA approved revision. with 130710-M KL, Rev J dated June 4, 20 17. or later FAA approved revision.

ldenticality per 14 CFR §2 1.303. per licensing agreement between Archeion Holdings, LLC and A vion ica, Inc. to use Supplement Type Certificate (STC) ST04375AT. issued June 27, 20 17, Archeion Holdings LLC. Master Drawing List DWG o. 160910-MDL. Rev A Dated June 12, 2017 or later FA A approved revision. with 130710-MKL, Rev J dated June 4. 2017. or later FAA approved revision.

Page 4 of7

PMA Project No. PQ 1734CE Supplement No. 44

Date: month dav, vear

I nsta I lat ion El igibi I ity: MAKE

Boeing

Boeing


8747-100/-200/-300/-400/SP/SR/-8/-8F

series

8747-100/-200/-300/-400/SP/SR/-8/-8F

series


A vionica, Inc. 9941 West Jessamine Street Miami, Florida 33 157 (786) 544-1100

Part Name

av PM (Personality Module). 4 SIM. 256MB

satLINK MAX with avRDC MAX Installation Kit

Part Number

804-0701-00

1307 10K-1


Modi ti cation Part

Modification Part


Identicali ty per 14 CF R §2 1.303. per licensing agreement between Archeion Holdings, LLC and A vionica. Inc. to use Supplement Type Certificate (STC) ST04375AT, issued June 27, 20 I 7, Archeion Holdings LLC. Master Drawing List DWG No. 160910-MDL. Rev A Dated June I 2, 20 I 7 or later FAA approved revision, with 1307 I 0-M KL, Rev J dated June 4, 20 17, or later FAA approved revision.

ldcnticali ty per 14 CFR §2 1.303, per licensing agreement between Archeion Holdings. LLC and Avionica. Inc. to use Supplement Type Certificate (STC) ST04375AT. issued June 27, 20 17, Archeion Holdings LLC. Master Drawing List DWG No. 160910-MDL, Rev A Dated June I 2, 2017 or later FAA approved revision. with 1307 10-M KL, Rev J dated June 4, 20 17, or later PAA approved revision.

Page 5 of7

PMA Project No. POI 734CE Supplement No. 44

Date: month dav, vear


Boeing

Boeing


8747- I 00/-200/-300/-400/SP/SR/-8/-8F

series

8747-1 00/-200/-300/-400/SP/SR/-8/-8F

series


Avionica, [nc. 9941 West Jessamine Street Miami , Florida 33157 (786) 544-1100

Part arne

satLINK MAX Installation Kit

satLINK MAX Upgrade Installation Kit

1307 1 OK-2

1307 IOK-3

Approved Replacement for Part

umber

Modification Part

Modification Part


ldenticality per 14 CFR §2 1.303, per licensing agreement between Archeion I foldings, LLC and A vionica. Inc. to use Supplement Type Certificate (STC) ST04375AT, issued June 27, 2017, Archeion Holdings LLC. Master Drawing List DWG o. 160910-MDL, Rev A Dated June 12, 20 17 or later FAA approved revision, with 130710-MKL. Rev J dated June 4, 2017, or later FAA approved revision.

ldenticality per 14 CFR §21.303. per licensing agreement between Archeion I foldings, LLC and A vionica, Inc. to use Supplement Type Certificate (STC) ST04375AT. issued June 27. 2017, Archeion Holdings LLC. Master Drawing List DWG No. 160910-MDL, Rev A Dated June 12. 2017 or later FAA approved revision. with 130710-MKL, Rev J dated June 4, 2017, or later FAA approved revision.

Page6of7


Date: month dav, vea r


Boeing

Boeing


874 7-100/-200/-300/-400/SP/SR/-8/-&F

series

8747- 100/-200/-300/-400/SP/SR/-8/-8F

series


A vionica, Inc. 9941 West Jessamine Street Miami , Florida 33157 (786) 544-1100

Pan Name Part Number

Approved Replacement for Pan Number




Installation Eligibility: MAK E

I nsta llat ion Eligibility: MODEL

-----------------------------End 0 f Listing----------------------

Note: The procedures that have been accepted by the type cenificate or TSO authorization holder and its cognizant FAA Aircraft Certification Office, for minor changes to original artic les used on type-certificated products. are also acceptable for incorporating the same minor changes on identical PMA replacement anicles The PMA holder must be able to show traceabihty relating to the TC, STC, or TSO authorization holder on all minor changes incorporated by this procedure When these procedures are no longer applicable because of completion of the production contract, or tennination of the licensing agreement or business relationship, all subsequent minor design changes to the PMA articles must be submined in a manner as determined by the ACO Major design changes (reference 14 CFR §2 1.319 and §21.619) to drawings and specifications are to be handled in the same manner as that for an original PMA.

John C. Kolin Manager, Orlando MIDO Section

Page 7 of 7

U.S. Depai1ment of Transportat ion

Federal Av iation Administration

March 28. 20 18

Avionica LLC. Attn : Jim Mo1Ta 99 14 Jessamine St. Miami, FL 33157

Airc raft Certifica tion Se rvice System Oversight Division Orlando M IDO Sec ti on 8-1 27 Southpark Circle. Suite 5 19 Orlando. FL 328 19-9058

Phone: ( 407)487-7200

PQ l 734CE

Ori ginal PMA Approval September 13 . 2004 Superseded PMA Approval February 28 . 201 8

FEDERAL AVIATION AD M INISTRATION - PARTS MANUFACTU RER APPROVA L

Dear Mr. Morra:

This is in response to Avionica Inc. letter dated February 13, 201 8 whereby you notified this offi ce of the name change from Avionica Inc. to Avioni ca LLC. while maintaining existing quality system , core management staff and fac ilities. The FAA has determined that Avionica LLC.. (hereinafter referred to as .. the Manu fac turer .. ) has established a quality system required by Ti tle 14 of the Code of Federal Regulations Part 21. sec tion 2 1.307 at 991 4 Jessamine St. Miami , FL 33 157. Accordingly. Parts Manu fac turing Approval (PMA) is hereby granted to produce the parts li sted in Supplements number 1 thru 44 in conformity with the FAA approved design data which includes, if applicable, Airpl ane Flight Manual Suppl ements and installation instructions and any changes subsequently approved. All changes to the des ign data must be approved in a manner acceptable to the FAA.

The follo wing terms and conditions appl y to this approval:

1. The Manufac turer·s quality system, methods. procedures. and manufac turing fac ilities. including suppliers. are subj ect to FAA surve illance and investi gations. Accordingly, the Manufacturer must advise its suppliers that their faciliti es are also subj ec t to FAA surveillance and investigations.

2. The Manufacturer must obtain approval fro m the Orlando Manufact uring Inspection Distric t Offi ce (M IDO) Section, prior to relocating or expanding manufac turing fac ilities from which articles are produced. including the addition of assoc iate fac ilities. Additionall y. thi s requirement applies to the Manufac turer· s suppliers with major inspection authori zation. and those suppliers who furni sh arti cles or related services where a determination of safety and confo rmance to the approved des ign cannot or will not be made upon receipt at the approved rece iving facility.

3. Upon request. the Manufac turer must make available to the FAA any pertinent in fo rmation concerni ng their suppliers \Nho furni sh parts/sen ices. Thi s includes:

a. A description of the pa11 or se rvice:

b. Where and by whom the part or se rvice will undergo inspection:

c. Any delegation of inspection duties:

d. Any delegation of materi als revievv authority:

e. The name and title of the FAA contac t at the supplier fac ility;

f. The inspection procedures required to be implemented:

g. Any direc t-shipment authority:

h. Results of the Manufac turer·s evaluation. audit, and/or surve illance of their suppliers:

i. The purchase/work order number (o r eq ui valent ): and

j . Any feedback relati ve to service difficulties ori ginating at the Manu facturer·s suppliers.

4. Parts. appliances. or manufacturing services furni shed by any suppliers located in a foreign country may not be used in the production of any arti cle or li sted in the enclosed supplement unless:

a. That part or service can and will be completely inspected fo r conformity at the Manufacturer' s U.S . facility; or

b. The FAA has determined the location of the fore ign supplier fac ility places no undue burden on the FAA in admini stering applicable airworthiness requirements. The Manu facturer must advise the FAA at least ten ( I 0) work ing days in advance when the use of such fo reign suppliers is contemplated. Thi s will allow the FAA time to make this determination.

5. Articles produced under the terms of thi s approval must be permanentl y marked with the identification info1mation as required by 14 CFR part 45. Identification and Registration Marking. § 45.15 . Use the letters .. FAA- PM A:· the name. trademark. or symbol of the company. and the part number. If the FAA finds the arti cle is too small or impracti cal to mark. the manufac turer must attach the info rmati on required by§ 45. 15 to the ai1icle or its container.

6. Thi s approva l is not transferable and it may be withdrawn fo r any reason that prec ludes its issuance or whenever the FAA finds the quality system is not being maintained. A withdrawal may occur if unsafe or nonconforming a11icles are accepted under the quality system.

7. The Orlando MIDO must approve any changes to the address shovrn in this appro val.

8. The Manu fac ture r must maintain its quality system in continuous compliance with the requirements of § 21.307. The Manufac turer also must ensure that each arti cle confo rms to the approved des ign data and is safe fo r installation on type-certifi cated products.

9. The Manufacturer has the pri vileges spec ifi ed within the PMA letter and suppl ement. In addition. the Manu facturer is eligible fo r the appointment of qualified individuals in its employ to represent the FAA as Designated Manu fac turing Inspec tion Representati ves (DMIRs). in accordance vvith the prov isions of pa11 183 . The DMIRs may iss ue export airworthiness approvals for arti cles. The Manu fac ture r may also be authori zed to apply fo r and obtain an Organizat ion Designation Authori zation (ODA). Orders 8100.8 and 8100 .1 5 contain procedures fo r the administration of DMIRs and ODAs, respect ive ly.

10. The Manufacturer must report in a timely manner. to the Orlando MIDO. in fo rmation concerning service difficulties on any ai1icle produced under th is approval. The Manufac turer also must report any failures. malfunctions. and defec ts that are required to be reported in acco rdance with § 21.3 .

11 . All tec hnical data required by § 21.303(a)(3 ), fo r the ai1icles to be produced in accordance with this approval, must be readil y avail able to the FAA at the facility where the articles are being produced.

12. The Manufac turer must noti fy the Orlando MIDO, immedi ate ly in writing of any changes to the quality system that may affect the inspecti on. confo rmity. or airworthiness of the a11icles approved in this letter.

13. The Manufac turer must produce all articles in accordance with Avionica LLC.. Quality System Manual. Rev E. dated December I. 20 11 that has been presented as ev idence of compliance with § 21.307. Accordingly. any revisions to the data must be submi tted to the Orlando MIDO Section fo r approval prior to implementation.

Sincerely.

John Ko lin Manager. Orlando MIDO Section

Avionica – Powering Secure Data and Communication Solutions

Documents

Transcript of Avionica – Powering Secure Data and Communication Solutions