Automation of calibration of instruments using labview - Project PPT
-
Upload
aman-singhla -
Category
Education
-
view
719 -
download
4
description
Transcript of Automation of calibration of instruments using labview - Project PPT
Automation Of Calibration Of Instruments Using
LabVIEWCalibration Of FLUKE 5500A Calibrator with
HP3458A Multimeter.
Automation Of Instruments
An Overview:
What is Automation?
Automation Federation define Automation as:
“ The creation and application of technology to monitor and control the production and
delivery of products and services.”
Quality
Productivity
Manpower Cost
Plant
Introduction to Virtual Instrumentation
• A virtual instrument consists of an industry-standard computer or workstation equipped with powerful
application software, cost-effective hardware such as plug-in boards, and driver software, which together
perform the functions of traditional instruments.
• Virtual instruments represent a fundamental shift from traditional hardware-centered instrumentation systems to software-centered systems that exploit the computing power, productivity, display, and connectivity capabilities of popular desktop computers and workstations.
Virtual Instrumentation: LabVIEW LabVIEW (short for Laboratory Virtual Instrumentation Engineering
Workbench) is a platform and development environment for a visual programming language from National Instruments.
DATA FLOW PROGRAMING: The programming language used in LabVIEW, also referred to as G, is
a dataflow programming language. Execution is determined by the structure of a graphical block diagram
(the LV-source code) on which the programmer connects different function-nodes by drawing wires.
GRAPHICAL PROGRAMMING: This type of programing uses graphics, icons and designs rather than
writing codes for programing. The graphical approach also allows non-programmers to build
programs simply by dragging and dropping virtual representations of lab equipment with which they are already familiar.
Comparison of LabVIEW with other Software's:
ABOUT THE PROJECT
The main task is to calibrate FLUKE 5500A CALIBRATOR with HP
3458A DIGITAL MULTIMETER using LabVIEW 12 software.
Fluke 5500
A Calibrator
HP3458A
Digital
Multimeter
LabVIEW
FLUKE 5500A Multi-Function Calibrator
The Fluke Model 5500A Multi-Product Calibrator is a precise instrument that calibrates a wide variety of electrical measuring instruments.
With the 5500A Calibrator, you can calibrate precision Multimeters that measure ac or dc voltage, ac or dc Current, ac or dc power, resistance, capacitance, and temperature.
With the Oscilloscope Calibration option, you can use the 5500A Calibrator to calibrate analog and digital Oscilloscopes.
Fluke 5500A Calibrator: Specifications
DC voltage from 0 V to ±1020 V.
AC voltage from 1 mV to 1020 V, with output from 10 Hz to 500 kHz.
AC current from 0.01 μA to 11.0 A, with output from 10 Hz to 10 kHz.
DC current from 0 to ±11.0 A.
Resistance values from a short circuit to 330 MΩ.
HP3458 Digital Multimeter
This DMM is characterized with both fast and accurate measurements.
3458A transfers high speed measurement data over GPIB or into and out of its 75,000 reading memory at 100,000 readings /second. Resolution of 8.5 digits.
Signal bandwidth of 12 MHz.
100,000 readings per second at 4 1/2 digits.
Other Hardware's:
This is a NI GPIB – GPIB cable which connects two instruments serially.
These are Double-shielded standard cables.
This is a NI GPIB – USB HS cable which connects an instrument and a computer.
Hi-Speed USB compliance; compatibility with USB 1.x full-speed ports.
Software’s Used:
Flow Diagram of Project:
DC Calibration Center
DC VoltDC Volt
AUXAC Volt
AC VoltAUX
Front Panel of Calibration Center:
DC Volt Main Screen:
Main Screen Of DC Volt AUX:
Main Screen of AC Volt:
Main Screen Of AC Volt AUX:
Thank You…Submitted By: Aman Singhla
Roll No.:101005004