Automatic Voice Frequency Test Sequences of ELQ 30A To learn more click on the selected topic! The...

11
Automatic Voice Frequency Test Sequences of ELQ 30A To learn more click on the selected topic! The Automatic Master-Slave Measuring mode is intended for the qualification of leased and dial-up voice frequency circuits. Two ELQ 30A connected to the ends of the tested line communicate over the tested line. The Master initializes the measurements and collects the results. The Slave performs the measurements according to the Master’s commands and sends the results back. Pre-programmed test parameter sets are provided based on recommendations: ITU-T M.1020 special quality leased circuits with special bandwidth conditioning ITU-T M.1025 special quality leased circuits with basic bandwidth conditioning ITU-T M.1040 ordinary quality leased circuits Using pre-programmed test parameter sets ELQ 30A provides immediate PASS/FAIL qualification and detailed information about the reasons of failure. ELEKTR NIKA Passive Leased Circuits Active Leased Circuits Dial-up (Switched) Circuits ITU-T Rec. for Passive Circuits ITU-T Rec. for Active Circuits

Transcript of Automatic Voice Frequency Test Sequences of ELQ 30A To learn more click on the selected topic! The...

Page 1: Automatic Voice Frequency Test Sequences of ELQ 30A To learn more click on the selected topic! The Automatic Master-Slave Measuring mode is intended for.

Automatic Voice Frequency Test Sequences of ELQ 30A

To learn more click on the selected topic!

The Automatic Master-Slave Measuring mode is intended for the qualification of leased and dial-up voice frequency circuits.

Two ELQ 30A connected to the ends of the tested line communicate over the tested line. ■ The Master initializes the measurements and collects the results. ■ The Slave performs the measurements according to the Master’s commands and sends the results back.

Pre-programmed test parameter sets are provided based on recommendations: ■ ITU-T M.1020 special quality leased circuits with special bandwidth conditioning ■ ITU-T M.1025 special quality leased circuits with basic bandwidth conditioning ■ ITU-T M.1040 ordinary quality leased circuits

Using pre-programmed test parameter sets ELQ 30A provides immediate PASS/FAIL qualification and detailed information about the reasons of failure.

ELEKTR NIKA

Passive Leased Circuits

Active Leased Circuits

Dial-up (Switched) Circuits

ITU-T Rec. for Passive Circuits

ITU-T Rec. for Active Circuits

Page 2: Automatic Voice Frequency Test Sequences of ELQ 30A To learn more click on the selected topic! The Automatic Master-Slave Measuring mode is intended for.

ELQ 30AELQ 30A

Qualification of Passive Leased Circuits (Cables)Selected system

Selected tests

Notice:■ The duration of EVENT test is 30 min therefore it is recommended only for trouble shooting !

Short form test result

ELEKTR NIKA

ELQ 30AELQ 30A

Detailed Results

Page 3: Automatic Voice Frequency Test Sequences of ELQ 30A To learn more click on the selected topic! The Automatic Master-Slave Measuring mode is intended for.

Detailed Results of Passive Leased Circuit Test

ELEKTR NIKA

Page 4: Automatic Voice Frequency Test Sequences of ELQ 30A To learn more click on the selected topic! The Automatic Master-Slave Measuring mode is intended for.

Qualification of Active Leased Circuits

Selected system

Selected tests

Short form test result

Notices:■ The duration of EVENT test is 30 min therefore it is recommended only for trouble shooting !■ The receiver delay should only be defined in case of extremely long lines

ELEKTR NIKA

Detailed Results

Page 5: Automatic Voice Frequency Test Sequences of ELQ 30A To learn more click on the selected topic! The Automatic Master-Slave Measuring mode is intended for.

Detailed Results of Active Leased Circuit Test

ELEKTR NIKA

Page 6: Automatic Voice Frequency Test Sequences of ELQ 30A To learn more click on the selected topic! The Automatic Master-Slave Measuring mode is intended for.

ELEKTR NIKA

Qualification of Dial-up (Switched ) Circuits

Click here for details

Page 7: Automatic Voice Frequency Test Sequences of ELQ 30A To learn more click on the selected topic! The Automatic Master-Slave Measuring mode is intended for.

Qualification of Dial-up (Switched ) Circuits

Notices:■ The duration of EVENT test is 30 min therefore it is recommended only for trouble shooting !■ The receiver delay should only be defined in case of extremely long lines

Selected system

Selected tests

Setting the phone number of slave

ELEKTR NIKA

Short form test result

Detailed Results

Page 8: Automatic Voice Frequency Test Sequences of ELQ 30A To learn more click on the selected topic! The Automatic Master-Slave Measuring mode is intended for.

Detailed Results of Switched Circuit Test

ELEKTR NIKA

Page 9: Automatic Voice Frequency Test Sequences of ELQ 30A To learn more click on the selected topic! The Automatic Master-Slave Measuring mode is intended for.

ITU-T Recommendations for Passive Circuits

Special quality circuits with special bandwidth conditioning

Special quality circuits with basic bandwidth conditioning

Ordinary quality circuits

Not specified

ELEKTR NIKA

Page 10: Automatic Voice Frequency Test Sequences of ELQ 30A To learn more click on the selected topic! The Automatic Master-Slave Measuring mode is intended for.

ITU-T Recommendations for Active Circuits

Special quality circuits with special bandwidth conditioning

Special quality circuits with basic bandwidth conditioning

Ordinary quality circuits

Not specified

ELEKTR NIKA

Page 11: Automatic Voice Frequency Test Sequences of ELQ 30A To learn more click on the selected topic! The Automatic Master-Slave Measuring mode is intended for.

THANK YOU FOR YOUR ATTENTION!