AutoCAD Course 15

8/9/2019 AutoCAD Course 15

1/11

Figure 1. To make this object, notice the absolute coordinate location of the smaller circle

(4,4.5) which is where you are going to start with. And the rest of the object follows with it.

Figure 2. This object is made with the advantage of the direct distance entry command to firstmake the perimeter (first without the curves). The curves in the sides can be made by usingthefilletorcircle-ttrcommand then trim.

AAppppeennddiixx::DDrraawwiinnggss 15


2/11

Figure 3. Again notice the absolute coordinate location of the line in 1, 3 and the point in 5,7

which is where the rest of the drawing follows.

Figure 4. This object again has absolute coordinates to follow. This is made through circles-

2P, lines, and ars (start-center-radius).

Figure 5. To make this object, start with the line, then the arcs. The center of the arc in 45 is

the endpoint of the location 1.50.


3/11

Figure 6. This drawing again has absolute coordinate locations to follow. The triangle is

made by following those commands given in numbered order. To circle inside the triangle ismade through cicle-ttrcommand.

Figure 7. Though this object can be made through lines and arcs, the objective is to make this

one using polylines wherein the lines and arcs are connected.


4/11

Figure 8. This object starts with the smaller circles with the diameter or 0.50 and the rest

follows. A circle-ttrcommand is more useful than using arc to make the curves.

Figure 9. This object is almost similar to figure 9 which also starts with the smaller circles.Again a cicle-ttrcommand is used here than arcs to make the curves. To copy the arc insideor outside at a different radius, the offsetcommand could be useful.


5/11

Figure 10. In this objects the direct distance entry could be useful to make the perimeter. For

the curves on the edge, filletcommand could also be used. Relative rectangular entry with

snap-from command could locate the circles center. To make the dash-dot center line youneed to load the line in the linetype box.

Figure 11. The objective of making this object is to learn the array (rectangular and polar)command. There are a total of 176 smaller circles. There are 40 circles around each inner

circles and 96 circles inside.


6/11

Figure 12. This exercise will help you use the chamfercommand which will help you makethe cut on the edge. The mirrorcommand is also used to reflect an object to its opposite side.

Fi

gure13.Dra ingexercis .


7/11

Fi

gure14.Dra ingexercis .PipeSpoolDesign.

Ite

1

2

3

4

5

6 7 8

Dim

3Fl

4Fl

3T

3,9

4x3

10 3Pi

nsionange

ange

e

0oElbow

Conc.Redu

pe

cer


8/11

Fi

gure15.Dra

SectionA

ingexercis

.BearingDesign.(seeCh rtfordimensions)

Item DA 1

B 2

C 1

D T

C

E 2

F 1

G

1

H 0

J 0

K 0

L 1

M 0

P 0

Q 0

S 0

T 2

U 0

W

0

Y 2

AA 1

BB 0

AK 0

AJ 1

TAP 0

imension.88

.44

.875

hru:0.266

bore:0.44

.00

.44

.06

.82

.50

.25

.3775

.188

.094

.13

.094

.84

.25

.52

.20

.75

.25

.871

.725

.136


9/11

A

1

Fi

Fi

B C

6 22 10

gure16.Dra

gure17.Dra

D E F

10 6 1

ingexercis

ingexercis

G H

20 31.8 2

.BoreCylind

.ButtHinge

J K

5.5 5 47

erDesign.S

Design.

L M

32.5 12

roke=5(Se

N P

30 7 3

Chartfordi

R S

0 94 63.6

mensions)

T

17


10/11

Fi

gure18.Dra ingexercis .PushLatchDesign


11/11

1.420"

2.75"

1.420"

2.57"

2.44"

2.18"

3.10"

3.03"

1/4-20 UNC-3BNUT MESHADJUSTMENT (2)

0.272"TM

4.000"4.50"

3.40"

1.420"

1/4-20 CAP HD BOLT2 PER CLEAT (OPTIONAL)

FOR END MOUNTING

1.420"

1.420"

0.257" THRU (4)

A

VIEW A-A

A

1.86"

MOTOR PLATE

MOTOR (OPTIONAL)

StabilNut

CARRIAGELEAD SCREW LIMIT SWITCH CAM

MOUNTING CLEATS (OPTIONAL)

COUPLING / BEARING COVER

END PLATE

ADJUSTABLE LIMIT SWITCHES(STANDARD ON MOTOR DRIVEN MODELS)

LIMIT SWITCH CONNECTOR

2.15"

0.355"

4.000"

4.60"

TRAVEL + 7.95" *

TRAVEL + 7.20" *

CARRIAGE FITADJUSTMENT(4)

2.040"

2.65"

Figure19.Drawingexercise.BiSlideAssembly.TravelLength=5inches

AutoCAD Course 15

Documents

Transcript of AutoCAD Course 15