ATV CAN-AM/BOMBARDIER Outlander 400, 500, 650, & 800 Plow ...
2
ATV CAN-AM/BOMBARDIER Outlander 400, 500, 650, & 800 Plow Mount Instructions Kit #60410 LOCK NUT REAR BRACKET RECEIVER FLAT WASHER HITCH PIN CLIP FOAM PAD MOUNT PIN HITCH PIN R-PIN BOLT SPACER MOUNT PLATE Tools: • 9/16” Wrench (2x) • Torque Wrench (ft. lbs.) 9/16” Socket • Tape Measure • Protective Eyewear 1 2 a) For ATV’s without skid plate, measure back 4 ½” on plow mount plate as shown. Wipe area clean and make mark. Apply adhesive side of foam pad next to mark as shown. NOTE: If ATV has a skid plate, foam pad is not used. Leave skid plate on and start with b) at right. a) Orientate rear mount bracket behind front tire/axle area as shown. View is of left side of machine. Note direction of flange legs with hole toward rear of machine. b) At front of machine, position and support mount plate up under frame with tabs to front of differential. Insert mount pin through hole in tab-then direct pin over top of machines frame, push it all the way through and into hole in tab on opposite side. (Tires may need to be turned) b) Position of bracket when on 500, 650, and 800 machines. c) At other side, push R-Pin into hole on mount pin. Mount can hang from frame for now. c) Position of bracket when on 400 machine. Foam Pad Mount Pin R-Pin Mount Tab Mount Tab Bend line on mount Tab with hole facing rear of machine Rear mount bracket 4½” NOTE: It may be necessary to trim excess plastic to allow clearance for rear bracket. Page 1 of 2 PN 60811_B ©Copyright 2013 Agri-Cover, Inc. All Rights Reserved 081613
Transcript of ATV CAN-AM/BOMBARDIER Outlander 400, 500, 650, & 800 Plow ...
ATV CAN-AM/BOMBARDIER Outlander 400, 500, 650, & 800 Plow Mount Instructions Kit #60410
LOCK NUT
REAR BRACKET
RECEIVER
FLAT WASHER
HITCH PIN CLIP
FOAMPAD
MOUNT PIN
HITCH PIN
R-PIN
BOLT
SPACER
MOUNTPLATE
Tools: • 9/16” Wrench (2x) • Torque Wrench (ft. lbs.) 9/16” Socket • Tape Measure • Protective Eyewear
1
2
a) For ATV’s without skid plate, measure back 4 ½” on plow mount plate as shown. Wipe area clean and make mark. Apply adhesive side of foam pad next to mark as shown. NOTE: If ATV has a skid plate, foam pad is not used. Leave skid plate on and start with b) at right.
a) Orientate rear mount bracket behind front tire/axle area as shown. View is of left side of machine. Note direction of flange legs with hole toward rear of machine.
b) At front of machine, position and support mount plate up under frame with tabs to front of differential. Insert mount pin through hole in tab-then direct pin over top of machines frame, push it all the way through and into hole in tab on opposite side. (Tires may need to be turned)
b) Position of bracket when on 500, 650, and 800 machines.
c) At other side, push R-Pin into hole on mount pin. Mount can hang from frame for now.
c) Position of bracket when on 400 machine.
Foam Pad
Mount Pin
R-Pin
MountTab
Mount Tab
Bend line on mount
Tab with hole facing rear of machine
Rear mount bracket
4½”
NOTE: It may be necessary to trim excess plastic to allow clearance for rear bracket.
Page 1 of 2
PN 60811_B ©Copyright 2013 Agri-Cover, Inc. All Rights Reserved 081613
3
4
a) For machines without skid plate, from bottom insert bolt up through mount plate, then 1 spacer, then through bracket. From top lay flat washer over bolt and turn lock nut on finger tight only.
a) Insert rear prong of receiver into notch under rear of mount plate.
b) Draw bolts tight evenly on each side-9/16” wrench. Torque bolts to 31ft.lbs.
b) Lift front of receiver up and insert receiver pin through flange mount plate, receiver and flange on other side.
c) Shows bolts drawn tight on machines without skid plate.
c) Insert hitch pin clip into hitch pin. Periodically check and retorque bolts if needed.
Rear Bracket
Spacer(See Note)
BottomMount
Part No. 60811_ Page 2 of 2 102009
NOTE: For machines with skid plate, use 2 spacers between bottom mount and bracket on each side.
