ATTENTION - Siemens Healthineers Flash/PDF...attention: reference document - not for construction....

SOMATOM DEFINITION FLASH

08013

A-101ATTENTION:

RE

FE

RE

NC

E D

OC

UM

EN

T - N

OT

F

OR

C

ON

ST

RU

CT

IO

N

AutoCAD SHX Text

DEFINITION FLASH

AutoCAD SHX Text

REV 12

AutoCAD SHX Text

RESOURCE LIST (SMS USE ONLY)

AutoCAD SHX Text

DESIGNATION

AutoCAD SHX Text

PG NUMBER

AutoCAD SHX Text

DATE

AutoCAD SHX Text


AutoCAD SHX Text

C2-030.891.01.29.02

AutoCAD SHX Text

08.17

AutoCAD SHX Text

COMMON CT

AutoCAD SHX Text

CT00-000.891.04.15.02

AutoCAD SHX Text

02.17

AutoCAD SHX Text

COMMON OPTIONS CT

AutoCAD SHX Text

CT00-000.891.03.38.02

AutoCAD SHX Text

03.17

AutoCAD SHX Text

TYPICAL FINAL DRAWING SET

AutoCAD SHX Text

AS NOTED

AutoCAD SHX Text

L. BACH

AutoCAD SHX Text

THE USE OR REPRODUCTION OF

AutoCAD SHX Text

THIS TITLE BLOCK WITHOUT

AutoCAD SHX Text

PROJECT #:

AutoCAD SHX Text

SHEET:

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

REF. #:

AutoCAD SHX Text

FULL EXTENT OF THE LAW.

AutoCAD SHX Text

SIEMENS AUTHORIZATION WILL

AutoCAD SHX Text

RESULT IN PROSECUTION UNDER

AutoCAD SHX Text

SHEET OF

AutoCAD SHX Text

DATE:

AutoCAD SHX Text

SHEET OF

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

HEIGHT DIFFERENCE BETWEEN HEAT EXCHANGER AND OUTDOOR UNIT MUST NOT EXCEED ±65-7".

AutoCAD SHX Text

THE MINIMUM ROOM VOLUME REQUIRED FOR THE WATER-AIR SPLIT HEAT EXCHANGER IS 424 CUBIC FEET.

AutoCAD SHX Text

SURGE SUPPRESSOR TO BE SUPPLIED BY SIEMENS, LOCATED AND INSTALLED BY CUSTOMER/CONTRACTOR. IF IT IS TO BE RELOCATED, IT MUST BE DEINSTALLED, RELOCATED AND REINSTALLED BY THE CUSTOMER/CONTRACTOR, IF NECESSARY. IT MUST BE LOCATED WITHIN 3'-0" OF THE CIRCUIT BREAKER.

AutoCAD SHX Text

THE OUTDOOR COOLING UNIT IS SUPPLIED BY SIEMENS, LOCATED AND INSTALLED BY THE CUSTOMER/ CONTRACTOR. THE INDOOR HEAT EXCHANGER CABINET IS SUPPLIED BY SIEMENS, INSTALLED BY THE CUSTOMER/CONTRACTOR. IF THE SYSTEM IS TO BE RELOCATED, THE OUTDOOR COOLING UNIT IS TO BE DEINSTALLED, RELOCATED AND REINSTALLED BY THE CUSTOMER/CONTRACTOR, IF NECESSARY. THE INDOOR HEAT EXCHANGER CABINET IS RELOCATED BY SIEMENS, INSTALLED BY THE CUSTOMER/CONTRACTOR.

AutoCAD SHX Text

NO OBSTRUCTION ZONE - THERE SHOULD BE NO CEILING MOUNTED ITEMS THAT HANG BELOW 86" AFF IN THIS AREA TO ALLOW FOR THE COVER OF THE GANTRY TO OPEN UP.

AutoCAD SHX Text

IT IS THE RESPONSIBILITY OF THE CUSTOMER/CONTRACTOR TO PROVIDE A MEANS OF MOUNTING THE PC TOWER(S) OFF FINISHED FLOOR FOR DAMAGE PROTECTION AGAINST TIP-OVER, FLUIDS, IMPACT, ETC. ADDITIONAL MOUNTING IS NOT NECESSARY IF SIEMENS CONTAINER IS UTILIZED.

AutoCAD SHX Text

HEIGHT OF WINDOW TO BE COORDINATED WITH COUNTERTOP/DESK HEIGHT.

AutoCAD SHX Text

CONTROL ROOM

AutoCAD SHX Text

CT SCAN ROOM

AutoCAD SHX Text

ORIENTATION POINT

AutoCAD SHX Text

6'-5" x 2'-7"

AutoCAD SHX Text

1

AutoCAD SHX Text

2

AutoCAD SHX Text

3

AutoCAD SHX Text

5

AutoCAD SHX Text

12

AutoCAD SHX Text

13

AutoCAD SHX Text

14

AutoCAD SHX Text

15

AutoCAD SHX Text

16

AutoCAD SHX Text

6

AutoCAD SHX Text

21

AutoCAD SHX Text

8

AutoCAD SHX Text

7

AutoCAD SHX Text

11

AutoCAD SHX Text

9

AutoCAD SHX Text

22

AutoCAD SHX Text

23

AutoCAD SHX Text

19

AutoCAD SHX Text

20

AutoCAD SHX Text

17

AutoCAD SHX Text

18

AutoCAD SHX Text

AS AN ALTERNATIVE, A SEPARATE SOURCE OF CHILLED WATER CAN BE PROVIDED BY THE CUTOMER/CONTRACTOR. SEE CHILLED WATER REQUIREMENTS, SHEET M-101A.

AutoCAD SHX Text

HEAT EXCHANGER CABINET IS NOT NEEDED IF HOSPITAL SUPPLIED CHILLED WATER IS USED.

AutoCAD SHX Text

EQUIPMENT ROOM

AutoCAD SHX Text

4

AutoCAD SHX Text

10

AutoCAD SHX Text

FINISHED ROOM HEIGHT

AutoCAD SHX Text

CAREVISION MONITOR/CEILING MOUNT

AutoCAD SHX Text

FOR CT GANTRY ONLY

AutoCAD SHX Text

MIN. 8'-6 3/8" MAX. 12'-1 1/16"

AutoCAD SHX Text

MINIMUM 7'-2 5/8"

AutoCAD SHX Text

N/A

AutoCAD SHX Text

TYPICAL REV 12

AutoCAD SHX Text

-ISSUE BLOCK-

AutoCAD SHX Text

DESCRIPTION

AutoCAD SHX Text

DATE

AutoCAD SHX Text

SYM

AutoCAD SHX Text

CUSTOMER FROM THE APPROPRIATE STATE AGENCY, IF APPLICABLE.

AutoCAD SHX Text

DIAGNOSTIC OR THERAPEUTIC PURPOSES, MUST BE OBTAINED BY THE

AutoCAD SHX Text

CONSTRUCTION OR STRUCTURAL MODIFICATIONS UTILIZING X-RAY FOR

AutoCAD SHX Text

PRIOR TO SIEMENS EQUIPMENT INSTALLATION, APPROVAL OF

AutoCAD SHX Text

STATE AGENCY REVIEW

AutoCAD SHX Text

ARCHITECTURAL EQUIPMENT PLAN

AutoCAD SHX Text

SCALE: 1/4" = 1'-0"

AutoCAD SHX Text

INSTALLATION & OPERATION OF THE SIEMENS EQUIPMENT.

AutoCAD SHX Text

HEREWITH, AS THEY ARE ESSENTIAL FOR THE SUCCESSFUL

AutoCAD SHX Text

CONTRACTOR. FOLLOW DESIGN RECOMMENDATIONS INCLUDED

AutoCAD SHX Text

DETAILED, FURNISHED AND INSTALLED BY THE CUSTOMER AND/OR

AutoCAD SHX Text

1) ALL CASEWORK IS EITHER EXISTING OR IS TO BE DESIGNED,

AutoCAD SHX Text

CASEWORK & ACCESSORY NOTES

AutoCAD SHX Text

BE PROVIDED BY THE CUSTOMER.

AutoCAD SHX Text

2) ALL FURNITURE (CHAIRS, ETC.) FOR THE CONTROL ROOM ARE TO

AutoCAD SHX Text

PLANNING REQUIREMENTS

AutoCAD SHX Text

EXAMINATION ROOM IN ACCORDANCE WITH LOCAL CODES.

AutoCAD SHX Text

EMERGENCY POWER OFF (EPO) BUTTONS REQUIRED IN CONTROL

AutoCAD SHX Text

AREA, EXAMINATION ROOM AND EQUIPMENT AREA.

AutoCAD SHX Text

DOOR (SAFETY) SWITCH REQUIRED ON ALL DOORS ACCESSING THE

AutoCAD SHX Text

SYSTEM COMPONENT

AutoCAD SHX Text

DECIBEL LEVEL

AutoCAD SHX Text

PDCA CABINET

AutoCAD SHX Text

(AT 3'-3" DISTANCE)

AutoCAD SHX Text

5555

AutoCAD SHX Text

PDCB CABINET

AutoCAD SHX Text

5555

AutoCAD SHX Text

IRS TOWER

AutoCAD SHX Text

5555

AutoCAD SHX Text

HEAT EXCHANGER - WATER/AIR SPLIT

AutoCAD SHX Text

<6060

AutoCAD SHX Text

NOISE LEVEL

AutoCAD SHX Text

PATIENT TABLE

AutoCAD SHX Text

<6060

AutoCAD SHX Text

GANTRY

AutoCAD SHX Text

<7070

AutoCAD SHX Text

ARCHITECTURAL NOTES

AutoCAD SHX Text

1) ALL PRELIMINARY EQUIPMENT LAYOUTS SUBMITTED BY SIEMENS HEALTHCARE ARE BASED ON THE RECOMMENDED SPACE NECESSARY FOR THE OPERATION AND SERVICEABILITY OF THE EQUIPMENT BEING PROPOSED. SIEMENS WILL NOT SUBMIT AN EQUIPMENT LAYOUT THAT IS NOT IN THE BEST INTEREST OF BOTH THE CUSTOMER AND SIEMENS. ALL EQUIPMENT LAYOUTS ARE BASED EITHER ON AN ACTUAL SITE SURVEY OR ARCHITECTURAL DRAWINGS SUPPLIED TO SIEMENS. SIEMENS WILL NOT BE RESPONSIBLE FOR ANY ALTERATIONS THAT ENCROACH WITHIN DESIGNATED SAFETY AND SERVICE CLEARANCE ZONES AS INDICATED ON DRAWINGS (I.E.. PIPE CHASES, VENTILATION DUCTS, CASEWORK, AND SOFFITS, ETC.) MADE BY THE CUSTOMER OR REQUIRED BY A CUSTOMER'S ARCHITECTURAL FIRM ONCE PRELIMINARY DRAWINGS HAVE BEEN SUBMITTED AND APPROVED. DO NOT ALTER ANY SPECIFICATIONS AND/OR DIMENSIONS WITHOUT CONTACTING AND RECEIVING WRITTEN CONFIRMATION FROM SIEMENS PROJECT MANAGER. 2) SIEMENS HEALTHCARE IS NOT AN ARCHITECTURAL OR ENGINEERING FIRM. DRAWINGS SUPPLIED BY SIEMENS ARE NOT CONSTRUCTION DRAWINGS. THEREFORE, THESE DRAWINGS ARE TO BE USED ONLY FOR INFORMATION TO COMPLEMENT ACTUAL CONSTRUCTION DRAWINGS AVAILABLE FROM A CUSTOMER APPOINTED ARCHITECTURAL REPRESENTATIVE OR A CUSTOMER'S ENGINEERING DESIGN GROUP. THE CUSTOMER'S ARCHITECT AND GENERAL CONTRACTOR SHALL BE ULTIMATELY RESPONSIBLE FOR COMPLIANCE WITH ALL APPLICABLE CODES AND PROFESSIONAL DESIGN REQUIREMENTS INCLUDING OSHA/NEC SAFETY CLEARANCE REQUIRMENTS IN ADDITION TO SIEMENS-REQUIRED SAFETY/SERVICE CLEARANCES SHOWN. 3) THE CUSTOMER IS RESPONSIBLE FOR ALL ROOM AND AREA PREPARATION COSTS, PROFESSIONAL FEES, PERMITS, REPORTS, AND INSPECTION FEES. 4) EQUIPMENT WARRANTIES, EXPRESSED OR IMPLIED ON THE PART OF SIEMENS SHALL BE CONTINGENT UPON STRICT COMPLIANCE WITH THE ARCHITECTURAL, STRUCTURAL, ELECTRICAL, MECHANICAL AND RECOMMENDATIONS AND REQUIREMENTS CONTAINED IN THESE DRAWINGS, UNLESS SPECIFIED OTHERWISE. 5) ALL DIMENSIONS SHOWN ARE FROM FINISHED SURFACES UNLESS SPECIFIED OTHERWISE. 6) THIS DRAWING DOES NOT PROVIDE RADIATION SHIELDING REQUIREMENTS FOR X-RAY AND ASSOCIATED EQUIPMENT. THE CUSTOMER IS RESPONSIBLE FOR CONSULTING WITH A REGISTERED RADIATION PHYSICIST. ACTUAL PROTECTION REQUIREMENTS SHALL BE SPECIFIED BY A REGISTERED RADIATION PHYSICIST AT CUSTOMER'S ENGAGEMENT AND EXPENSE. RESPONSIBILITY FOR ALL INFORMATION AS TO THE ROOM LOCATION, USE, AND NUMBER OF ANTICIPATED EXAMINATIONS TO BE PERFORMED PER TIME PERIOD SHALL BE PROVIDED TO THE PHYSICIST BY THE CUSTOMER. THE CUSTOMER SHALL FURTHER TAKE ALL RESPONSIBILITY IN THE COMMUNICATION AND COORDINATION OF ACTIVITIES OF THE RADIATION PHYSICIST AND THE ARCHITECTURAL REPRESENTATIVE. 7) SIEMENS HEALTHCARE SHALL BE RESPONSIBLE FOR SIEMENS EQUIPMENT INSTALLATION, CALIBRATION, CONNECTION AND INSTALLATION OF SIEMENS PROVIDED CABLES. THE CUSTOMER/ELECTRICAL CONTRACTOR IS RESPONSIBLE FOR TERMINATIONS OF CUSTOMER/ELECTRICAL CONTRACTOR-SUPPLIED CABLES TO SIEMENS EQUIPMENT. IN THE EVENT THAT SPECIFIC TRADE RULES OR LICENSE REQUIREMENTS PROHIBIT THIS, THE CUSTOMER SHALL INITIATE THE SERVICES OF APPROVED OTHER CONTRACTORS AND PAY FOR SELECTED, APPROVED PARTIES TO PERFORM THIS WORK WITH SUPERVISION PROVIDED BY SIEMENS. CALIBRATION WHEN ACCOMPLISHED OUTSIDE OF NORMAL INSTALLATION SEQUENCES DUE TO CONTRACTOR OR TRADE RULE ACTIONS OR REQUIREMENTS SHALL BE SUPPORTED BY, CHARGED TO, AND ACCEPTED BY THE CUSTOMER AS AN ADDITIONAL INSTALLATION EXPENSE. 8) THE CUSTOMER SHALL COORDINATE WITH SIEMENS PROJECT MANAGER THE LOCATIONS AND TRAVEL OF ALL ANCILLARY EQUIPMENT TO BE CEILING OR WALL MOUNTED (I.E.: O.R. LIGHTS, MEDICAL GAS COLUMNS, PHYSIOLOGICAL MONITORING INJECTORS, CRT PLATFORMS, SPRINKLER HEADS, SMOKE DETECTORS, ELECTRICAL OUTLETS, HVAC GRILLES, SPEAKERS, AND GENERAL ROOM LIGHTING, ETC.). 9) THE GENERAL CONTRACTOR/CUSTOMER SHALL BE RESPONSIBLE FOR ALL FINAL PAINT, TOUCH-UP AND ANY COSMETIC OR TRIM WORK WHICH NEEDS TO BE OR IS REQUIRED TO BE COMPLETED AFTER THE INSTALLATION OF THE SIEMENS EQUIPMENT AND ANY ASSOCIATED SUPPORT APPARATUS.

AutoCAD SHX Text

TRANSPORT AND DELIVERY NOTES

AutoCAD SHX Text

DURING THE MOVEMENT OF THE GANTRY THROUGH CORRIDORS THE TRANSPORT CASTERS ARE SWIVELED OUT FOR STABILITY AS SHOWN BELOW. THE MAXIMUM WIDTH IS 5'-10 7/8" AND THE MAX. LENGTH IS 8'-8 1/8" WHEN CASTERS ARE SWIVELED OUT.

AutoCAD SHX Text

NORMAL TRANSPORT REQUIREMENTS:

AutoCAD SHX Text

NARROW SPACE TRANSPORT REQUIREMENTS:

AutoCAD SHX Text

WHEN TRANSPORTING THE GANTRY THROUGH A NARROW SPACE OR DOORWAY, THE TRANSPORT CASTERS ARE SWIVELED IN AS SHOWN BELOW. THE MAXIMUM WIDTH IS 3'-11 3/8" AND MAXIMUM LENGTH 10'-11 1/8".

AutoCAD SHX Text

TOTAL GANTRY TRANSPORT WEIGHT: 6,317 LBS.

AutoCAD SHX Text

GANTRY WITHOUT TRANSPORT DEVICE: 5,689 LBS. TRANSPORT DEVICE: 628 LBS.

AutoCAD SHX Text

EQUIPMENT LEGEND

AutoCAD SHX Text

NO

AutoCAD SHX Text

DESCRIPTION

AutoCAD SHX Text

SMS

AutoCAD SHX Text

WEIGHT

AutoCAD SHX Text

BTU/HR

AutoCAD SHX Text

DIMENSIONS (INCHES)

AutoCAD SHX Text

REMARKS

AutoCAD SHX Text

SYM

AutoCAD SHX Text

(LBS)

AutoCAD SHX Text

TO AIR

AutoCAD SHX Text

W

AutoCAD SHX Text

D

AutoCAD SHX Text

H

AutoCAD SHX Text

1

AutoCAD SHX Text

-

AutoCAD SHX Text

OPERATING CONSOLE (OPTION)

AutoCAD SHX Text

132

AutoCAD SHX Text

43

AutoCAD SHX Text

47 1/4

AutoCAD SHX Text

31 1/2

AutoCAD SHX Text

29 1/4

AutoCAD SHX Text

2

AutoCAD SHX Text

-

AutoCAD SHX Text

19" FLAT SCREEN MONITOR ICS, KEYBOARD AND CONTROL BOX

AutoCAD SHX Text

-

AutoCAD SHX Text

---

AutoCAD SHX Text

---

AutoCAD SHX Text

---

AutoCAD SHX Text

---

AutoCAD SHX Text

3

AutoCAD SHX Text

PIT

AutoCAD SHX Text

POWER CONNECTION TERMINAL - ICS

AutoCAD SHX Text

---

AutoCAD SHX Text

---

AutoCAD SHX Text

---

AutoCAD SHX Text

---

AutoCAD SHX Text

---

AutoCAD SHX Text

WALL MOUNTED

AutoCAD SHX Text

4

AutoCAD SHX Text

-

AutoCAD SHX Text

DVI SPLITTER - ICS

AutoCAD SHX Text

---

AutoCAD SHX Text

---

AutoCAD SHX Text

15 3/4

AutoCAD SHX Text

3 15/16

AutoCAD SHX Text

11 13/16

AutoCAD SHX Text

MOUNTED ON THE CONSOLE/CONTAINER

AutoCAD SHX Text

5

AutoCAD SHX Text

ICS

AutoCAD SHX Text

SYNGO ACQUISITION WORKPLACE

AutoCAD SHX Text

<55

AutoCAD SHX Text

1,706

AutoCAD SHX Text

7 5/16

AutoCAD SHX Text

19

AutoCAD SHX Text

17

AutoCAD SHX Text

OFF FLOOR/IN CONTAINER

AutoCAD SHX Text

6

AutoCAD SHX Text

-

AutoCAD SHX Text

IMAGE EVALUATION KEYBOARD (OPTION)

AutoCAD SHX Text

-

AutoCAD SHX Text

---

AutoCAD SHX Text

---

AutoCAD SHX Text

---

AutoCAD SHX Text

---

AutoCAD SHX Text

ON CUSTOMER'S COUNTER

AutoCAD SHX Text

7

AutoCAD SHX Text

-

AutoCAD SHX Text

19" FLAT SCREEN MONITOR FOR IES (OPTION)

AutoCAD SHX Text

20

AutoCAD SHX Text

256

AutoCAD SHX Text

16 9/16

AutoCAD SHX Text

8 1/4

AutoCAD SHX Text

16 1/16

AutoCAD SHX Text

ON CONSOLE/COUNTER

AutoCAD SHX Text

8

AutoCAD SHX Text

IES

AutoCAD SHX Text

SYNGO CT WORKPLACE (OPTION)

AutoCAD SHX Text

<66

AutoCAD SHX Text

1,706

AutoCAD SHX Text

9 13/16

AutoCAD SHX Text

29 1/2

AutoCAD SHX Text

18 1/2

AutoCAD SHX Text

OFF FLOOR/IN CONTAINER

AutoCAD SHX Text

9

AutoCAD SHX Text

-

AutoCAD SHX Text

UPS FOR IES (OPTION)

AutoCAD SHX Text

36

AutoCAD SHX Text

171

AutoCAD SHX Text

9 3/16

AutoCAD SHX Text

16 7/16

AutoCAD SHX Text

5 13/16

AutoCAD SHX Text

10

AutoCAD SHX Text

PIT2

AutoCAD SHX Text

POWER CONNECTION TERMINAL - IES (OPTION)

AutoCAD SHX Text

---

AutoCAD SHX Text

---

AutoCAD SHX Text

---

AutoCAD SHX Text

---

AutoCAD SHX Text

---

AutoCAD SHX Text

WALL MOUNTED

AutoCAD SHX Text

11

AutoCAD SHX Text

-

AutoCAD SHX Text

CONTAINER FOR ICS/IES (OPTION)

AutoCAD SHX Text

77

AutoCAD SHX Text

---

AutoCAD SHX Text

31 1/2

AutoCAD SHX Text

31 1/2

AutoCAD SHX Text

29 1/4

AutoCAD SHX Text

HOUSING FOR ICS/IES

AutoCAD SHX Text

12

AutoCAD SHX Text

B

AutoCAD SHX Text

SOMATOM DEFINITION FLASH GANTRY

AutoCAD SHX Text

5,689

AutoCAD SHX Text

3,412*

AutoCAD SHX Text

91 1/8

AutoCAD SHX Text

47 3/8

AutoCAD SHX Text

78

AutoCAD SHX Text

*ADDITIONAL HEAT DISSIPATED TO WATER

AutoCAD SHX Text

13

AutoCAD SHX Text

-

AutoCAD SHX Text

PATIENT TABLE

AutoCAD SHX Text

1,103

AutoCAD SHX Text

*

AutoCAD SHX Text

29 1/2

AutoCAD SHX Text

95 11/16

AutoCAD SHX Text

33 7/16

AutoCAD SHX Text

*INCLUDED IN THE GANTRY BTU FIGURE

AutoCAD SHX Text

14

AutoCAD SHX Text

PDCA

AutoCAD SHX Text

POWER DISTRIBUTION CABINET "A"

AutoCAD SHX Text

1,213

AutoCAD SHX Text

13,649**

AutoCAD SHX Text

35 7/16

AutoCAD SHX Text

26 15/16

AutoCAD SHX Text

76 3/4

AutoCAD SHX Text

UPS LOCATED INSIDE OF PDCA

AutoCAD SHX Text

15

AutoCAD SHX Text

PDCB

AutoCAD SHX Text

POWER DISTRIBUTION CABINET "B"

AutoCAD SHX Text

882

AutoCAD SHX Text

**

AutoCAD SHX Text

35 7/16

AutoCAD SHX Text

26 15/16

AutoCAD SHX Text

76 3/4

AutoCAD SHX Text

**PDCA & PDCB COMBINED

AutoCAD SHX Text

16

AutoCAD SHX Text

IRS

AutoCAD SHX Text

IMAGE RECONSTRUCTION SYSTEM

AutoCAD SHX Text

62

AutoCAD SHX Text

5,122

AutoCAD SHX Text

10

AutoCAD SHX Text

26 3/16

AutoCAD SHX Text

20

AutoCAD SHX Text

17

AutoCAD SHX Text

S

AutoCAD SHX Text

HEAT EXCHANGER CABINET - WATER/AIR SPLIT (OPTION)

AutoCAD SHX Text

910

AutoCAD SHX Text

3,412

AutoCAD SHX Text

39 3/8

AutoCAD SHX Text

27 1/4

AutoCAD SHX Text

77

AutoCAD SHX Text

18

AutoCAD SHX Text

S2

AutoCAD SHX Text

OUTDOOR UNIT - WATER/AIR SPLIT (OPTION)

AutoCAD SHX Text

410

AutoCAD SHX Text

119,504

AutoCAD SHX Text

100 3/4

AutoCAD SHX Text

42 1/8

AutoCAD SHX Text

45 5/16

AutoCAD SHX Text

19

AutoCAD SHX Text

F1

AutoCAD SHX Text

CARE VISION DUAL MONITOR (OPTION)

AutoCAD SHX Text

174

AutoCAD SHX Text

---

AutoCAD SHX Text

---

AutoCAD SHX Text

---

AutoCAD SHX Text

---

AutoCAD SHX Text

CEILING MOUNTED

AutoCAD SHX Text

20

AutoCAD SHX Text

SPD

AutoCAD SHX Text

EATON SURGE PROTECTIVE DEVICE PANEL (OPTION)

AutoCAD SHX Text

13.5

AutoCAD SHX Text

---

AutoCAD SHX Text

7 1/2

AutoCAD SHX Text

6 11/16

AutoCAD SHX Text

12

AutoCAD SHX Text

WALL MOUNTED

AutoCAD SHX Text

21

AutoCAD SHX Text

IN1

AutoCAD SHX Text

MEDRAD DISPLAY CONTROL UNIT (OPTION)

AutoCAD SHX Text

8

AutoCAD SHX Text

---

AutoCAD SHX Text

12 1/2

AutoCAD SHX Text

9

AutoCAD SHX Text

13 1/2

AutoCAD SHX Text

HEIGHT WITH SCREEN UP

AutoCAD SHX Text

22

AutoCAD SHX Text

IN2

AutoCAD SHX Text

MEDRAD BASE UNIT (OPTION)

AutoCAD SHX Text

14

AutoCAD SHX Text

---

AutoCAD SHX Text

11

AutoCAD SHX Text

8 3/4

AutoCAD SHX Text

11 1/2

AutoCAD SHX Text

UNDER COUNTER ON SHELF

AutoCAD SHX Text

23

AutoCAD SHX Text

IN3

AutoCAD SHX Text

CEILING MOUNTED MEDRAD INJECTOR (OPTION)

AutoCAD SHX Text

106

AutoCAD SHX Text

---

AutoCAD SHX Text

---

AutoCAD SHX Text

---

AutoCAD SHX Text

---

AutoCAD SHX Text

SEE MFG SPECIFICATIONS

AutoCAD SHX Text

IT IS RECOMMENDED THAT THE SIEMENS DRAWINGS BE INCORPORATED WITH THE CONSTRUCTION

AutoCAD SHX Text

THIS DRAWING IS DESIGNED TO CONFORM TO FEATURES AND EQUIPMENT REQUIREMENTS PRESENTED

AutoCAD SHX Text

AT THE TIME OF THEIR PREPARATION. SINCE BOTH THESE FACTORS ARE SUBJECT TO DESIGN

AutoCAD SHX Text

MODIFICATION, THEY ARE NOT TO BE USED FOR CONSTRUCTION PURPOSES.

AutoCAD SHX Text

DOCUMENTS FOR REFERENCE.

AutoCAD SHX Text

THIS DRAWING DOES NOT PROVIDE RADIATION SHIELDING REQUIREMENTS FOR X-RAY AND ASSOCIATED

AutoCAD SHX Text

EQUIPMENT. THE CUSTOMER IS RESPONSIBLE FOR CONSULTING WITH A REGISTERED RADIATION

AutoCAD SHX Text

PHYSICIST TO SPECIFY RADIATION PROTECTION.

AutoCAD SHX Text

ALL DIMENSIONS SHOWN ON THIS DRAWING ARE FROM FINISHED SURFACES.

AutoCAD SHX Text

THIS SET OF PLANS REPRESENTS A COMPLETE SET OF DETAILS AND SHOULD NOT BE SEPARATED.

AutoCAD SHX Text

ALL RIGHTS ARE RESERVED.

AutoCAD SHX Text

1 8


08013

A-102ATTENTION:

RE

FE

RE

NC

E D

OC

UM

EN

T - N

OT

F

OR

C

ON

ST

RU

CT

IO

N

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

FOR CT GANTRY ONLY

AutoCAD SHX Text

MIN. 8'-6 3/8" MAX. 12'-1 1/16"

AutoCAD SHX Text

MINIMUM 7'-2 5/8"

AutoCAD SHX Text

CT SCAN ROOM

AutoCAD SHX Text

CONTROL ROOM

AutoCAD SHX Text

ORIENTATION POINT

AutoCAD SHX Text

SAFETY CLEARANCE

AutoCAD SHX Text

SERVICE CLEARANCE

AutoCAD SHX Text

TABLE MOVEMENT

AutoCAD SHX Text

SERVICE CLEARANCE

AutoCAD SHX Text

EQUIPMENT ROOM

AutoCAD SHX Text

SERVICE CLEARANCE

AutoCAD SHX Text

SERVICE CLEARANCE

AutoCAD SHX Text


AutoCAD SHX Text

AS NOTED

AutoCAD SHX Text

L. BACH

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

PROJECT #:

AutoCAD SHX Text

SHEET:

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

REF. #:

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

SHEET OF

AutoCAD SHX Text

DATE:

AutoCAD SHX Text

SHEET OF

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

N/A

AutoCAD SHX Text

TYPICAL REV 12

AutoCAD SHX Text

-ISSUE BLOCK-

AutoCAD SHX Text

DESCRIPTION

AutoCAD SHX Text

DATE

AutoCAD SHX Text

SYM

AutoCAD SHX Text

DEFINITION FLASH

AutoCAD SHX Text

REV 12

AutoCAD SHX Text

SIEMENS REMOTE SERVICE

AutoCAD SHX Text

TO ENSURE THE UPTIME OF YOUR SYSTEM DURING THE WARRANTY PERIOD (AND BEYOND WITH A SERVICE AGREEMENT), SIEMENS REMOTE SERVICES (SRS) REQUIRES REMOTE LOCAL AREA NETWORK ACCESS TO SIEMENS SYSTEMS.

AutoCAD SHX Text

THE PREFERRED CONNECTION METHOD IS (VPN) VIRTUAL PRIVATE NETWORK (WHERE THE CUSTOMER HAS AVAILABLE A VPN CAPABLE FIREWALL OR OTHER VPN APPLIANCE). THIS METHOD PROVIDES THE POSSIBILITY FOR REMOTE SYSTEM DIAGNOSTICS WITHOUT ADDITIONAL HARDWARE. PLEASE CONTACT SIEMENS REMOTE SERVICES (800-888-SIEM) TO DETERMINE IF THIS METHOD IS SUITABLE FOR YOUR SITE.

AutoCAD SHX Text

CUSTOMER VPN SERVER

AutoCAD SHX Text

CUSTOMER DMZ

AutoCAD SHX Text

IMAGING DEVICE SINGLE HOST IP OR IP SUBNET LIST

AutoCAD SHX Text

SIEMENS REMOTE SERVICES DMZ

AutoCAD SHX Text

PUBLIC INTERNET

AutoCAD SHX Text

FIREWALL

AutoCAD SHX Text

SRS ACCESS SERVER

AutoCAD SHX Text

CISCO 3745 ROUTER

AutoCAD SHX Text

SAFETY/SERVICE CLEARANCE PLAN

AutoCAD SHX Text

SCALE: 1/4" = 1'-0"

AutoCAD SHX Text

IF THE SAFETY DISTANCES ARE NOT OBSERVED, SAFETY MEASURES IN ACCORDANCE WITH LOCAL CODES SHOULD BE UTILIZED (FOR EXAMPLE BARRIERS, WARNING SIGNS, AND SAFETY MATS).

AutoCAD SHX Text

SAFETY CLEARANCE NOTE

AutoCAD SHX Text

SCANNING WAS PERFORMED USING A MAXIMUM SLICE THICKNESS OF 64 x 0.6 mm (38.4 mm) AT 140 kV THROUGH THE SYSTEM AXIS IN THE HORIZONTAL PLANE. PHANTOM USED: CYLINDRICAL PMMA PHANTOM, 32 cm IN DIAMETER, 15 CM LONG. THE PHANTOM WAS CENTERED IN THE TOMOGRAPHIC PLANE.

AutoCAD SHX Text

RADIATION SCATTER

AutoCAD SHX Text

HORIZONTAL LOCAL DOSE DISTRIBUTION

AutoCAD SHX Text

INCHES

AutoCAD SHX Text

INCHES

AutoCAD SHX Text

.0027

AutoCAD SHX Text

.0181

AutoCAD SHX Text

.0773

AutoCAD SHX Text

.0856

AutoCAD SHX Text

.0760

AutoCAD SHX Text

.0160

AutoCAD SHX Text

.0027

AutoCAD SHX Text

.0012

AutoCAD SHX Text

.0026

AutoCAD SHX Text

.1526

AutoCAD SHX Text

.2180

AutoCAD SHX Text

.1580

AutoCAD SHX Text

.0031

AutoCAD SHX Text

.0013

AutoCAD SHX Text

.0014

AutoCAD SHX Text

.0006

AutoCAD SHX Text

.0011

AutoCAD SHX Text

.0032

AutoCAD SHX Text

.0155

AutoCAD SHX Text

.0510

AutoCAD SHX Text

.3490

AutoCAD SHX Text

.7110

AutoCAD SHX Text

.3775

AutoCAD SHX Text

.0494

AutoCAD SHX Text

.0149

AutoCAD SHX Text

.0298

AutoCAD SHX Text

.0906

AutoCAD SHX Text

.1369

AutoCAD SHX Text

.1763

AutoCAD SHX Text

.1331

AutoCAD SHX Text

.0890

AutoCAD SHX Text

.0305

AutoCAD SHX Text

.0390

AutoCAD SHX Text

.0521

AutoCAD SHX Text

.0650

AutoCAD SHX Text

.0752

AutoCAD SHX Text

.0660

AutoCAD SHX Text

.0533

AutoCAD SHX Text

.0386

AutoCAD SHX Text

.0278

AutoCAD SHX Text

.0333

AutoCAD SHX Text

.0374

AutoCAD SHX Text

.0410

AutoCAD SHX Text

.0363

AutoCAD SHX Text

.0327

AutoCAD SHX Text

.0279

AutoCAD SHX Text

.0200

AutoCAD SHX Text

.0221

AutoCAD SHX Text

.0228

AutoCAD SHX Text

.0214

AutoCAD SHX Text

.0238

AutoCAD SHX Text

.0229

AutoCAD SHX Text

.0199

AutoCAD SHX Text

.0146

AutoCAD SHX Text

.0159

AutoCAD SHX Text

.0165

AutoCAD SHX Text

.0146

AutoCAD SHX Text

.0162

AutoCAD SHX Text

.0158

AutoCAD SHX Text

.0151

AutoCAD SHX Text

59.1

AutoCAD SHX Text

39.4

AutoCAD SHX Text

19.7

AutoCAD SHX Text

0

AutoCAD SHX Text

-19.7

AutoCAD SHX Text

-39.4

AutoCAD SHX Text

-59.1

AutoCAD SHX Text

-78.7

AutoCAD SHX Text

-98.4

AutoCAD SHX Text

-118.1

AutoCAD SHX Text

-78.7

AutoCAD SHX Text

-59.1

AutoCAD SHX Text

-39.4

AutoCAD SHX Text

-19.7

AutoCAD SHX Text

0

AutoCAD SHX Text

19.7

AutoCAD SHX Text

39.4

AutoCAD SHX Text

59.1

AutoCAD SHX Text

78.7

AutoCAD SHX Text

78.7

AutoCAD SHX Text

-137.8

AutoCAD SHX Text

.0050

AutoCAD SHX Text

.0297

AutoCAD SHX Text

.0445

AutoCAD SHX Text

.0466

AutoCAD SHX Text

.0435

AutoCAD SHX Text

.0293

AutoCAD SHX Text

.0072

AutoCAD SHX Text

.0113

AutoCAD SHX Text

.0119

AutoCAD SHX Text

.0119

AutoCAD SHX Text

.0108

AutoCAD SHX Text

.0118

AutoCAD SHX Text

.0118

AutoCAD SHX Text

.0117

AutoCAD SHX Text

MEASUREMENT IN uGy/mAs SCALE 1/4"=1'-0"

AutoCAD SHX Text


AutoCAD SHX Text

.0009

AutoCAD SHX Text

.8645

AutoCAD SHX Text

.0031

AutoCAD SHX Text

SCANNING WAS PERFORMED USING A MAXIMUM SLICE THICKNESS OF 64 x 0.6 mm (38.4 mm) AT 140 kV THROUGH THE SYSTEM AXIS IN THE VERTICAL PLANE. PHANTOM USED: CYLINDRICAL PMMA PHANTOM, 32 cm IN DIAMETER, 15 CM LONG. THE PHANTOM WAS CENTERED IN THE TOMOGRAPHIC PLANE.

AutoCAD SHX Text

RADIATION SCATTER

AutoCAD SHX Text

VERTICAL LOCAL DOSE DISTRIBUTION

AutoCAD SHX Text

INCHES

AutoCAD SHX Text

INCHES

AutoCAD SHX Text

.0557

AutoCAD SHX Text

.0876

AutoCAD SHX Text

.0362

AutoCAD SHX Text

.0017

AutoCAD SHX Text

.0007

AutoCAD SHX Text

.0028

AutoCAD SHX Text

.0209

AutoCAD SHX Text

.0795

AutoCAD SHX Text

.1418

AutoCAD SHX Text

.0699

AutoCAD SHX Text

.0752

AutoCAD SHX Text

.0856

AutoCAD SHX Text

.0599

AutoCAD SHX Text

.1322

AutoCAD SHX Text

.3528

AutoCAD SHX Text

NA

AutoCAD SHX Text

NA

AutoCAD SHX Text

39.4

AutoCAD SHX Text

19.7

AutoCAD SHX Text

0

AutoCAD SHX Text

-19.7

AutoCAD SHX Text

-39.4

AutoCAD SHX Text

-78.7

AutoCAD SHX Text

-59.1

AutoCAD SHX Text

-39.4

AutoCAD SHX Text

-19.7

AutoCAD SHX Text

0

AutoCAD SHX Text

19.7

AutoCAD SHX Text

39.4

AutoCAD SHX Text

59.1

AutoCAD SHX Text

78.7

AutoCAD SHX Text

.2180

AutoCAD SHX Text

MEASUREMENT IN uGy/mAs SCALE 1/4"=1'-0"

AutoCAD SHX Text

.0315

AutoCAD SHX Text

.0456

AutoCAD SHX Text

.0466

AutoCAD SHX Text

.0353

AutoCAD SHX Text

NA

AutoCAD SHX Text

.0363

AutoCAD SHX Text

.0400

AutoCAD SHX Text

.0410

AutoCAD SHX Text

.0026

AutoCAD SHX Text

NA

AutoCAD SHX Text

.0247

AutoCAD SHX Text

.0257

AutoCAD SHX Text

.0214

AutoCAD SHX Text

.0020

AutoCAD SHX Text

NA

AutoCAD SHX Text

.0179

AutoCAD SHX Text

.0188

AutoCAD SHX Text

.0146

AutoCAD SHX Text

.0017

AutoCAD SHX Text

NA

AutoCAD SHX Text

.0137

AutoCAD SHX Text

.0134

AutoCAD SHX Text

.0108

AutoCAD SHX Text

.0014

AutoCAD SHX Text

NA

AutoCAD SHX Text

.3388

AutoCAD SHX Text

.1369

AutoCAD SHX Text

.7110

AutoCAD SHX Text

.1763

AutoCAD SHX Text

98.4

AutoCAD SHX Text

118.1

AutoCAD SHX Text

137.8

AutoCAD SHX Text

59.1

AutoCAD SHX Text

.0419

AutoCAD SHX Text

.0362

AutoCAD SHX Text

.0064

AutoCAD SHX Text

.0022

AutoCAD SHX Text

.0009

AutoCAD SHX Text

.0013

AutoCAD SHX Text

.0031

AutoCAD SHX Text

.0110

AutoCAD SHX Text

.0306

AutoCAD SHX Text

.0225

AutoCAD SHX Text

.0172

AutoCAD SHX Text

.0129

AutoCAD SHX Text


AutoCAD SHX Text

.8645

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

2 8


08013

S-101ATTENTION:

RE

FE

RE

NC

E D

OC

UM

EN

T - N

OT

F

OR

C

ON

ST

RU

CT

IO

N

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

FOR CT GANTRY ONLY

AutoCAD SHX Text

MIN. 8'-6 3/8" MAX. 12'-1 1/16"

AutoCAD SHX Text

MINIMUM 7'-2 5/8"

AutoCAD SHX Text

CONTROL ROOM

AutoCAD SHX Text

CT SCAN ROOM

AutoCAD SHX Text

NOTE: FOR THE WEIGHTS OF ALL SIEMENS EQUIPMENT SHOWN ON THIS PLAN, SEE THE "EQUIPMENT LEGEND" ON SHEET A-101.

AutoCAD SHX Text

ORIENTATION POINT

AutoCAD SHX Text

EQUIPMENT ROOM

AutoCAD SHX Text

S-101

AutoCAD SHX Text

1

AutoCAD SHX Text

S-101

AutoCAD SHX Text

4

AutoCAD SHX Text

S-101

AutoCAD SHX Text

3

AutoCAD SHX Text

S-101

AutoCAD SHX Text

2

AutoCAD SHX Text


AutoCAD SHX Text

AS NOTED

AutoCAD SHX Text

L. BACH

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

PROJECT #:

AutoCAD SHX Text

SHEET:

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

REF. #:

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

SHEET OF

AutoCAD SHX Text

DATE:

AutoCAD SHX Text

SHEET OF

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

N/A

AutoCAD SHX Text

TYPICAL REV 12

AutoCAD SHX Text

-ISSUE BLOCK-

AutoCAD SHX Text

DESCRIPTION

AutoCAD SHX Text

DATE

AutoCAD SHX Text

SYM

AutoCAD SHX Text

DEFINITION FLASH

AutoCAD SHX Text

REV 12

AutoCAD SHX Text

STRUCTURAL FLOOR PLAN

AutoCAD SHX Text

SCALE: 1/4" = 1'-0"

AutoCAD SHX Text

PDC CABINET BASE

AutoCAD SHX Text

BOLTING THE POWER DISTRIBUTION CABINETS TO THE FLOOR IS ONLY NECESSARY WHEN LOCAL OR NATIONAL REGULATIONS REQUIRE IT. (EXAMPLE: EARTHQUAKE ZONES). BOLT THE CABINETS TO THE FLOOR USING ANCHORS THROUGH THE DRILL HOLES IN THE FLOOR PLATE. MATERIALS FOR BOLTING MUST BE SUPPLIED ON-SITE.

AutoCAD SHX Text

POWER DISTRIBUTION CABINET A AND POWER DISTRIBUTION CABINET B

AutoCAD SHX Text

THE FOOTPRINTS OF PDCA AND PDCB ARE IDENTICAL.

AutoCAD SHX Text

FRONT

AutoCAD SHX Text

OPENING IN CABINET BASE FOR CABLE INLET

AutoCAD SHX Text

(4) 9/16" HOLES

AutoCAD SHX Text

SCALE: 1/2"=1'-0"

AutoCAD SHX Text

2

AutoCAD SHX Text

(4) ADJUSTABLE FEET OF GANTRY - 3 1/8". 11/16" FLOOR MOUNTING HOLES THROUGH THEGANTRY FEET, IF REQUIRED.

AutoCAD SHX Text

MAXIMUM POSSIBLE EXTRACTION FORCE AT THESE POINTS IS 1824 POUNDS WITH A 507 POUND PATIENT (INCLUDES SAFETY-FACTOR 4).

AutoCAD SHX Text

GANTRY AND PATIENT TABLE MOUNTING DETAIL

AutoCAD SHX Text

(4) 3/4" MOUNTING HOLES / ADJUSTABLEFEET TO MOUNT THE PATIENT TABLE TO THE FLOOR.

AutoCAD SHX Text

SUPPLIED AND INSTALLED BY SIEMENS.

AutoCAD SHX Text

THE GANTRY AND PATIENT TABLE ARE

AutoCAD SHX Text

2

AutoCAD SHX Text

2a

AutoCAD SHX Text

1

AutoCAD SHX Text

THE PATIENT TABLE MUST ALWAYS BE BOLTED TO THE FLOOR THROUGH THE ATTACHMENT POINTS IN THE TABLE PEDESTAL. A DRILLING TEMPLATE AND ALL INSTALLATION MATERIALS ARE INCLUDED IN THE DELIVERY FOR STANDARD ANCHORING. ANCHOR: HILTI HSL-3G M10/60 (USED WITHOUT BONDED SCREED) OR HSL-3G M10/120 (USED WITH MAX. 2 3/8" BONDED SCREED) ARE SUPPLIED WITH THE TABLE. THE CONCRETE MUST BE MIN. 5 1/2" THICK.

AutoCAD SHX Text

THE WEIGHT CAPACITY OF THE FLOOR MUST BE EVALUATED BY A STRUCTURAL ENGINEER. BOLTING THE GANTRY TO THE FLOOR IS ONLY NECESSARY WHEN LOCAL OR NATIONAL REGULATIONS REQUIRE IT (EXAMPLE: EARTHQUAKE ZONES). BOLT THE GANTRY TO THE FLOOR USING ANCHORS THROUGH THE MOUNTING HOLES IN THE GANTRY BASE. MATERIALS FOR BOLTING MUST BE SUPPLIED ON-SITE.

AutoCAD SHX Text

BOLTING REQUIREMENTS

AutoCAD SHX Text

1

AutoCAD SHX Text

FLOOR SURFACE REQUIREMENTS

AutoCAD SHX Text

IT IS THE RESPONSIBILITY OF THE STRUCTURAL ENGINEER TO DETERMINE THE ANCHORING DEPTH AND CONCRETE STRENGTH NEEDED TO INSTALL THE TABLE BASE WITH THE SIEMENS SUPPLIED ANCHORS OR EQUIVALENT ANCHORS SPECIFIED BY THE STRUCTURAL ENGINEER AND SUPPLIED BY THE CUSTOMER/CONTRACTOR.

AutoCAD SHX Text

THE CONCRETE FLOOR MUST BE LEVEL WITHIN 3/8" MAXIMUM DEVIATION IN THE AREA AROUND THE BASE OF THE GANTRY AND THE BASE OF THE PATIENT TABLE.

AutoCAD SHX Text

THE GANTRY AND PATIENT TABLE MUST BE INSTALLED ON THE SAME PLANE. IT IS THE CUSTOMER'S RESPONSIBILITY TO MEET FLOOR LEVELNESS SPECIFICATIONS AS OUTLINED IN THIS DETAIL. THE GANTRY AND PATIENT TABLE MUST BE PLACED DIRECTLY ON THE CONCRETE FLOOR. EXISTING FLOOR COVERING IN THE AREA OF THE INSTALLATION SUPPORT SURFACE AND ATTACHMENT POINTS OF THE GANTRY AND THE ENTIRE FOOTPRINT AREA OF THE PATIENT TABLE BASE MUST BE REMOVED AND REPLACED WITH SHIMS OF THE APPROPRIATE THICKNESS. THE GANTRY AND PATIENT TABLE RESTS ON ADJUSTABLE FEET AND ANY LEVELING IS DONE WITH THE ADJUSTABLE FEET.

AutoCAD SHX Text

1

AutoCAD SHX Text

ORIENTATION POINT

AutoCAD SHX Text

1

AutoCAD SHX Text

1

AutoCAD SHX Text

2

AutoCAD SHX Text

2

AutoCAD SHX Text

2a

AutoCAD SHX Text

1

AutoCAD SHX Text

SCALE: 1/2"=1'-0"

AutoCAD SHX Text

3

AutoCAD SHX Text

3

AutoCAD SHX Text

3

AutoCAD SHX Text

(4) 3/4" ALTERNATE FLOOR MOUNTING HOLES.

AutoCAD SHX Text

3

AutoCAD SHX Text

THE FOLLOWING APPROVED CHEMICAL ANCHORS MAY BE USED WHEN STANDARD ANCHORS ARE NOT POSSIBLE. TO BE SUPPLIED BY THE CUSTOMER/CONTRACTOR: 1. HILTI INJECTABLE ADHESIVE ANCHOR: HIT-RE 500-V3 HARDENING TIME AT TEMP. FROM 68°-75° - 7 HOURS2. HILTI INJECTABLE ADHESIVE ANCHOR: HIT-HY 200-A HARDENING TIME AT TEMP. FROM 70°-86° - 30 MIN.3. HILTI INTERNALLY THREADED INSERT: HIS-N M10X110 USE THIS SIZE WHEN REPLACING AN ANCHOR. MIN. CONCRETE THICKNESS: 6" 4. HILTI INTERNALLY THREADED INSERT: HIS-N M8X90 USED WHEN MOUNTING HOLES HAVE NOT BEEN DRILLED. MIN. CONCRETE THICKNESS: 4 3/4".

AutoCAD SHX Text

4

AutoCAD SHX Text

4

AutoCAD SHX Text

3

AutoCAD SHX Text

2

AutoCAD SHX Text

1

AutoCAD SHX Text

3

AutoCAD SHX Text

1

AutoCAD SHX Text

2

AutoCAD SHX Text

FLOOR LOADING

AutoCAD SHX Text

±152

AutoCAD SHX Text

±156

AutoCAD SHX Text

±171

AutoCAD SHX Text

±175

AutoCAD SHX Text

1) THE VALUES PROVIDED FOR FLOOR LOADING APPLY ONLY IF THE GANTRY IS SATISFACTORILY LEVELED.

AutoCAD SHX Text

2) THE FLOOR STRUCTURE MUST BE CAPABLE OF WITHSTANDING THE OCCUPIED WEIGHT OF THE GANTRY AND THE INDIVIDUAL CONTACT AREA LOADING.

AutoCAD SHX Text

STATIC FLOOR LOADING DUE TO GANTRY'S OWN WEIGHT

AutoCAD SHX Text

DIFFERENCE BETWEEN MINIMUM AND MAXIMUM FLOOR LOADING DURING GANTRY ROTATION

AutoCAD SHX Text

F STAT MAX

AutoCAD SHX Text

AMPLITUDE

AutoCAD SHX Text

MEASUREMENT POINTS

AutoCAD SHX Text

ADJUSTABLE FOOT

AutoCAD SHX Text

F STAT MAX (POUNDS)

AutoCAD SHX Text

AMPLITUDE FOR F DYN (POUNDS)

AutoCAD SHX Text

BEARING AREA PER ADJUSTABLE FOOT

AutoCAD SHX Text

1272

AutoCAD SHX Text

1717

AutoCAD SHX Text

1768

AutoCAD SHX Text

1476

AutoCAD SHX Text

2

AutoCAD SHX Text

7 3/4 IN

AutoCAD SHX Text

DESCRIPTION

AutoCAD SHX Text

NOTE:

AutoCAD SHX Text

FLOOR AND BUILDING VIBRATIONS

AutoCAD SHX Text

THE THRESHOLD IS DEFINED AS ACCELERATION RMS VALUE (ROOT MEAN SQUARE) IN M/S² OF AN FFT SPECTRUM DERIVED WITH A FREQUENCY RESOLUTION OF 1 Hz AND USING A HANNING-WINDOW. THE VIBRATIONS HAVE TO BE MEASURED WITH A SAMPLING RATE OF 1000Hz USING AN ANTI-ALIASING-FILTER WITH A LIMIT FREQUENCY OF 250Hz. THE THRESHOLD IS VALID FOR VIBRATIONS AT THE INSTALLATION LOCATION WITH A CT IN POSITION. MEASUREMENTS ARE USUALLY TAKEN AT THE SITE BEFORE THE INSTALLATION OF THE CT, CHANGES IN THE EIGENFREQUENCY OF THE SLAB CAUSED BY THE ADDITIONAL MASS OF THE CT HAVE TO BE CONSIDERED WHEN COMPARING THE FREQUENCY SPECTRUM WITH THE THRESHOLD.

AutoCAD SHX Text

TRANSIENT VIBRATIONS (SHOCKS)

AutoCAD SHX Text

ANY TRANSIENT VIBRATION HAS TO BE LESS THAN 0.5 M/S² PEAK-TO-PEAK IN THE TIME DOMAIN. THE VIBRATIONS HAVE TO BE MEASURED WITH A SAMPLING RATE OF 1000Hz.

AutoCAD SHX Text

THE CT SYSTEM IS NOT SENSITIVE TO COMMON VIBRATIONS. IF THE CT IS AWAY FROM VIBRATIONAL SOURCES OR THE CT IS REPLACING A CT SYSTEM, THAT TO DATE, HAS NOT SHOWN IMAGE QUALITY PROBLEMS DUE TO VIBRATIONS, IT IS USUALLY NOT NECESSARY TO EXECUTE VIBRATIONAL MEASUREMENTS. IF THERE ARE ANY DOUBTS, THE FOLLOWING THRESHOLDS HAVE TO BE VERIFIED BY MEASUREMENT: IN THE THREE SPATIAL DIRECTIONS, ACCELERATION IN VIBRATIONS AT THE MOUNTING POINTS OF THE COMPUTED TOMOGRAPHY SYSTEM (GANTRY AND THE PATIENT HANDLING SYSTEM PHS) MUST NOT EXCEED THE THRESHOLDS AS DESCRIBED HERE.

AutoCAD SHX Text

FREQUENCY (Hz)

AutoCAD SHX Text

0.01

AutoCAD SHX Text

1

AutoCAD SHX Text

CONTINUOUS VIBRATIONS

AutoCAD SHX Text

ALLOWABLE ACCELERATION RMS-VALUE M/S²

AutoCAD SHX Text

10

AutoCAD SHX Text

100

AutoCAD SHX Text

0.10

AutoCAD SHX Text

1.00

AutoCAD SHX Text

SURGE SUPPRESSOR

AutoCAD SHX Text

REV 0

AutoCAD SHX Text

PARALLEL SURGE SUPPRESSOR UNIT MUST BE LOCATED WITHIN 3 FEET OF CIRCUIT BREAKER.

AutoCAD SHX Text

EATON SPD

AutoCAD SHX Text

SURGE SUPPRESSOR, SUPPLIED BY SIEMENS AND INSTALLED BY THE CUSTOMER/CONTRACTOR. SURGE SUPPRESSOR IS WALL MOUNTED, CONTRACTOR TO SUPPLY BACKING AND MOUNTING HARDWARE. MAINTAIN A MINIMUM OF 36" IN FRONT OF SURGE SUPPRESSOR FOR SERVICE.

AutoCAD SHX Text

WEIGHT: 13.5 LBS.

AutoCAD SHX Text

FOUR .20" MOUNTING SLOTS

AutoCAD SHX Text

INPUT POWER (FROM LEFT SIDE)

AutoCAD SHX Text

FRONT VIEW

AutoCAD SHX Text

SIDE VIEW

AutoCAD SHX Text

SCALE: NONE

AutoCAD SHX Text

4

AutoCAD SHX Text

HE CABINET BASE

AutoCAD SHX Text

FRONT

AutoCAD SHX Text

BOLTING THE HEAT EXCHANGER CABINET TO THE FLOOR IS ONLY NECESSARY WHEN LOCAL OR NATIONAL REGULATIONS REQUIRE IT. (EXAMPLE: EARTHQUAKE ZONES). BOLT THE CABINET TO THE FLOOR USING ANCHORS THROUGH THE DRILL HOLES IN THE FLOOR PLATE. MATERIALS FOR BOLTING MUST BE SUPPLIED ON-SITE.

AutoCAD SHX Text

HEAT EXCHANGER CABINET (WATER/AIR SPLIT COOLING SYSTEM)

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

1/2"=1'-0"

AutoCAD SHX Text

(4) 5/8" HOLES

AutoCAD SHX Text

OPENING IN CABINET BASE FOR CABLE/HOSE INLET

AutoCAD SHX Text

3

AutoCAD SHX Text

STRUCTURAL NOTES

AutoCAD SHX Text

1) THE CUSTOMER/CONTRACTOR SHALL FURNISH AND INSTALL ALL STRUCTURAL SUPPORT MEMBERS AND NEEDED HARDWARE FOR THE INSTALLATION OF THE SIEMENS EQUIPMENT. 2) THE OVERHEAD STRUCTURAL SUPPORT SYSTEM SHALL BE FIXED, RIGID AND BRACED FOR SWAY. 3) ALL STRUCTURAL SUPPORT MEMBERS SHALL BE TRUE, SQUARE, LEVEL, PARALLEL AND COPLANAR WITH RESPECT TO EACH OTHER, WITH A HORIZONTAL STRUCTURAL SUPPORT MEMBER TO BE LOCATED AND SET WITH A TRANSIT. 4) ALL STRUCTURAL SUPPORT DETAILS SHOWN ARE SAMPLE DETAILS BASED UPON TYPICAL AND STANDARD BUILDING PRACTICES AND ARE NOT INTENDED AS ACTUAL CONSTRUCTION DETAILS. ALL CONSTRUCTION DETAILS AND SUPPORT CALCULATIONS SHALL BE PREPARED BY A PROFESSIONAL STRUCTURAL ENGINEER AT THE CUSTOMER'S EXPENSE. IN THE EVENT AN EXISTING SUPPORT SYSTEM IS TO BE USED, IT WILL BE THE CUSTOMER'S RESPONSIBILITY TO VERIFY THE INTEGRITY OF THAT SYSTEM. 5) MOUNTING PLATES, FRAMES, AND HARDWARE SUPPLIED BY SIEMENS AS DETAILED IN THIS DRAWING SET ARE INSTALLED BY SIEMENS UNLESS OTHERWISE REQUIRED. ANY DEVIATION FROM THE PROVIDED MATERIALS OR MOUNTING METHODS MUST BE DESIGNED AND DOCUMENTED BY THE STRUCTURAL ENGINEER OF RECORD. ALTERNATE MOUNTING MATERIALS (I.E. ANCHORS, THREADED ROD, BACKING PLATES, ETC.) MUST BE SUPPLIED BY THE CUSTOMER/CONTRACTOR. SIEMENS MAY REQUIRE ASSISTANCE FROM THE CUSTOMER/CONTRACTOR WITH INSTALLATION WHEN UTILIZING ALTERNATE MOUNTING MATERIALS. 6) ALL CEILING FIXTURES (I.E. AIR SUPPLY GRILLES, AIR RETURN GRILLES, EXHAUST GRILLES, SPRINKLER HEADS, INCANDESCENT AND FLUORESCENT LIGHT FIXTURES, INTERCOM SPEAKERS, MEDICAL GAS COLUMNS, ETC.) SHALL BE INSTALLED FLUSH MOUNTED WITH THE FINISHED CEILING TO PROVIDE FREE AND UNRESTRICTED TRAVEL OF THE SMS CEILING MOUNTED EQUIPMENT. 7) THE BOTTOM SIDE OF THE UNISTRUT CEILING GRID AND ANY CEILING MOUNTED SUPPORT PLATES ARE TO BE INSTALLED FLUSH WITH THE FINISHED CEILING. THE CUSTOMER/CONTRACTOR SHALL ALSO PROVIDE COVERSTRIPS FOR THE UNISTRUT. 8) THE STRUCTURAL PLANNING AS SHOWN ON THE 1/4" STRUCTURAL PLAN HAS BEEN COORDINATED WITH THE EQUIPMENT LOCATION AS SHOWN ON THE 1/4" EQUIPMENT LAYOUT PLAN. FOR THIS REASON, ANY DEVIATIONS FROM THE STRUCTURAL PLANNING AS SHOWN MUST BE APPROVED BY SMS PLANNING DEPARTMENT. 9) THE STRUCTURAL ENGINEER OF RECORD SHALL BE RESPONSIBLE FOR THE DESIGN AND DETAIL OF FLOOR, WALL, AND CEILING STRUCTURES IN ACCORDANCE WITH THE STRUCTURAL INFORMATION SHOWN, AND LOCAL GOVERNING BUILDING CODES.

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

3 8


08013

S-102ATTENTION:

RE

FE

RE

NC

E D

OC

UM

EN

T - N

OT

F

OR

C

ON

ST

RU

CT

IO

N

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

FOR CT GANTRY ONLY

AutoCAD SHX Text

MIN. 8'-6 3/8" MAX. 12'-1 1/16"

AutoCAD SHX Text

MINIMUM 7'-2 5/8"

AutoCAD SHX Text

NOTE: FOR THE WEIGHTS OF ALL SIEMENS EQUIPMENT SHOWN ON THIS PLAN, SEE THE "EQUIPMENT LEGEND" ON SHEET A-101.

AutoCAD SHX Text

CONTROL ROOM

AutoCAD SHX Text

CT SCAN ROOM

AutoCAD SHX Text

ORIENTATION POINT

AutoCAD SHX Text

EQUIPMENT ROOM

AutoCAD SHX Text

S-102

AutoCAD SHX Text

1

AutoCAD SHX Text

S-102

AutoCAD SHX Text

2

AutoCAD SHX Text


AutoCAD SHX Text

AS NOTED

AutoCAD SHX Text

L. BACH

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

PROJECT #:

AutoCAD SHX Text

SHEET:

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

REF. #:

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

SHEET OF

AutoCAD SHX Text

DATE:

AutoCAD SHX Text

SHEET OF

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

N/A

AutoCAD SHX Text

TYPICAL REV 12

AutoCAD SHX Text

-ISSUE BLOCK-

AutoCAD SHX Text

DESCRIPTION

AutoCAD SHX Text

DATE

AutoCAD SHX Text

SYM

AutoCAD SHX Text

DEFINITION FLASH

AutoCAD SHX Text

REV 12

AutoCAD SHX Text

STRUCTURAL CEILING PLAN

AutoCAD SHX Text

SCALE: 1/4" = 1'-0"

AutoCAD SHX Text

MEDRAD INJECTOR (CL)

AutoCAD SHX Text

INJECTOR

AutoCAD SHX Text

MEDRAD

AutoCAD SHX Text

SUPPORT ARM

AutoCAD SHX Text

HORIZONTAL

AutoCAD SHX Text

CEILING MOUNTING PLATE DETAIL

AutoCAD SHX Text

FINISHED FLOOR

AutoCAD SHX Text

NONE

AutoCAD SHX Text

REV 2

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

MOUNT

AutoCAD SHX Text

CEILING

AutoCAD SHX Text

ASSEMBLY

AutoCAD SHX Text

MOUNTING FLANGE

AutoCAD SHX Text

METAL FRAMEWORK

AutoCAD SHX Text

DECK ABOVE

AutoCAD SHX Text

12"

AutoCAD SHX Text

CEILING

AutoCAD SHX Text

UNISTRUT

AutoCAD SHX Text

PULL BOX "IN3"

AutoCAD SHX Text

1

AutoCAD SHX Text

FOUR 3/8" DIA. A325 BOLTS (SUPPLIED BY MEDRAD) FOR MOUNTING THE COUNTERPOISE MOUNTING FLANGE TO THE MOUNTING PLATE

AutoCAD SHX Text

FOUR 1/2" DIA. A307 BOLTS FOR ANCHORING THE MOUNTING PLATE TO UNISTRUT OR SUPPORT FRAME, SUPPLIED AND INSTALLED BY CUSTOMER/CONTRACTOR.

AutoCAD SHX Text

3/8" THICK STEEL MOUNTING PLATE, SUPPLIED BY MEDRAD AND INSTALLED BY CUSTOMER/CONTRACTOR.

AutoCAD SHX Text

TOTAL HUNG WEIGHT OF THE COUNTERPOISE SYSTEM AND INJECTOR: 106 LBS.

AutoCAD SHX Text

MOUNTING PLATE, SUPPLIED BY MEDRAD, INSTALLED BY CUSTOMER/CONTRACTOR. LOCATED EVEN WITH CEILING IF STANDARD MOUNT IS USED.

AutoCAD SHX Text

THERE SHOULD BE SPACE ABOVE THE MOUNTING PLATE TO ACCESS NUTS AND LOCK WASHERS DURING INSTALLATION.

AutoCAD SHX Text

MINIMUM

AutoCAD SHX Text

33 1/2" MEDIUM MOUNT (OPTION)

AutoCAD SHX Text

39 3/8" LONG MOUNT (OPTION)

AutoCAD SHX Text

GANTRY HEIGHT +2" MIN. ABOVE FINISHED FLOOR RECOMMENDED

AutoCAD SHX Text

SUPPORT STRUCTURE FOR CEILING MOUNTING PLATE MUST BE DESIGNED BY AN ENGINEER, BRACED FOR SWAY, AND INSTALLED BY A QUALIFIED CONTRACTOR.

AutoCAD SHX Text

CARE VISION OVERHEAD SUPPORT SIDE ELEVATION

AutoCAD SHX Text

NONE

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

FROM AFF TO UNFINISHED CEILING

AutoCAD SHX Text

8'-6 3/8" TO 10'-2"

AutoCAD SHX Text

ROOM HEIGHT WITH SHORT FLANGE PIPE

AutoCAD SHX Text

UNFINISHED CEILING

AutoCAD SHX Text

INTERMEDIATE CEILING

AutoCAD SHX Text

FINISHED FLOOR

AutoCAD SHX Text

1) IF THE ROOM HEIGHT DOES NOT FALL WITHIN THE RECOMMENDED RANGE, THE MONITOR VIEW ZONE DOES NOT COVER THE ENTIRE RANGE OF THE PREFERRED 4'-7" TO 5'-7" RANGE. IN THIS CASE, WE RECOMMEND USING THE MONITOR TROLLEY. 2) A FREE SPACE OF AT LEAST 2" BETWEEN THE HIGHEST GANTRY POINT (EX. GANTRY TILT, OPENED SERVICE LID, ETC) AND THE LOWEST MCS CONTACT POINT MUST BE MAINTAINED. OTHERWISE ONLY THE MONITOR TROLLEY IS PERMITTED. A) LOWEST CONTACT POINT IF PLACED OVER ISOCENTER. B) LOWEST CONTACT POINT IF NOT PLACED OVER ISOCENTER. 3) SHORTENING OF THE FLANGE PIPES IS NOT PERMITTED.

AutoCAD SHX Text

-

AutoCAD SHX Text

10'-2" TO 12'-1 11/16"

AutoCAD SHX Text

ROOM HEIGHT WITH LONG FLANGE PIPE

AutoCAD SHX Text

RECOMMENDED RANGE NOTE 1)

AutoCAD SHX Text

2'-7 3/8"

AutoCAD SHX Text

LONG FLANGE

AutoCAD SHX Text

SHORT FLANGE

AutoCAD SHX Text

LONG FLANGE

AutoCAD SHX Text

SHORT FLANGE

AutoCAD SHX Text

2'-9 3/4"

AutoCAD SHX Text

HIGHEST POSITION

AutoCAD SHX Text

LOWEST POSITION

AutoCAD SHX Text

LONG FLANGE

AutoCAD SHX Text

SHORT FLANGE

AutoCAD SHX Text

10 3/4"

AutoCAD SHX Text

6'-7"

AutoCAD SHX Text

LONG FLANGE

AutoCAD SHX Text

SHORT FLANGE

AutoCAD SHX Text

NOTE 2)

AutoCAD SHX Text

2B)

AutoCAD SHX Text

2A)

AutoCAD SHX Text

CARE VISION MONITOR CEILING MOUNT DETAIL

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

1" = 1'-0"

AutoCAD SHX Text

THE WEIGHT CAPACITY OF THE CEILING MUST BE EVALUATED BY A STRUCTURAL ENGINEER. 1) SIX SPACERS WITH THREADED BORES FOR MOUNTING THE FLANGE PIPE CEILING PLATE. 2) FOUR THREADED BORES FOR THE THREADED RODS. 3) HOLES FOR MOUNTING TO UNFINISHED CEILING. 4) HOLES FOR THREADED RODS. 5) THREADED RODS, SUPPLIED BY SIEMENS AND INSTALLED BY CUSTOMER/CONTRACTOR. 6) CANOPY "SMALL" - 1'-1 3/8" "BIG" - 1'-7 11/16""BIG" CANOPY IS MANDATORY FOR UNFINISHED CEILING INSTALLTION. 7) FLANGE PIPE IS ALREADY ASSEMBLED TO THE SUPPORT ARM WHEN DELIVERED. "SHORT" FLANGE PIPE: LENGTH= 11 3/16", AVAILABLE FOR ROOMS WITH A CEILING HEIGHT UP TO 10'-2". "LONG" FLANGE PIPE: LENGTH= 2'-7 1/2", AVAILABLE FOR ROOMS WITH A CEILING HEIGHT ABOVE 10'-2". 8) SPACER SLEEVES CONTAINING THREADED RODS BY SIEMENS AND INSTALLED BY THE CUSTOMER/CONTRACTOR. THREADED RODS ARE SUPPLIED IN 3'-3 3/8" LENGTHS AND MAY BE SHORTENED TO ACCOMMODATE CEILING HEIGHT. 9) SPACER PLATE: ALWAYS IN THE CENTER OF THE SUBCONSTRUCTION. NOT NEEDED IF TOTAL SUBCONSTRUCTION LENGTH IS <1'-7 11/16". 10) HOLES FOR MOUNTING CEILING PLATE TO THE INTERFACE PLATE. 11) THREADED BORE FOR M16 FOR TAP BOLT (HORIZONTAL ADJUSTMENT) 12) THREADED BORE M6 FOR GROUNDING CONNECTION. THE SYSTEM CABLES ARE ROUTED THROUGH THE FLANGE PIPE. A DRILLING TEMPLATE IS INCLUDED IN THE DELIVERY VOLUME FOR THE ANCHOR PLATE. 6 HILTI PASS-THROUGH ANCHORS ARE INCLUDED IN THE DELIVERY VOLUME, HSL-3-G M12/50, SUPPLIED BY SIEMENS, EXTRACTION FORCE IS MIN. 1,349 LBS. AT EACH CEILING MOUNTING POINT.

AutoCAD SHX Text

UNFINISHED CEILING INSTALLATION

AutoCAD SHX Text

INTERMEDIATE CEILING INSTALLATION

AutoCAD SHX Text

INTERFACE PLATE, 1/2" THICK, SUPPLIED BY SIEMENS AND INSTALLED BY THE CUSTOMER/ CONTRACTOR.

AutoCAD SHX Text

CEILING PLATE, 1/2" THICK, SUPPLIED AND INSTALLED BY SIEMENS.

AutoCAD SHX Text

ANCHOR PLATE, 1/2" THICK, SUPPLIED BY SIEMENS AND INSTALLED BY THE CUSTOMER/ CONTRACTOR.

AutoCAD SHX Text

1)

AutoCAD SHX Text

2)

AutoCAD SHX Text

5/8" (4)

AutoCAD SHX Text

1 1/2" (6)

AutoCAD SHX Text

INTERFACE PLATE

AutoCAD SHX Text

5)

AutoCAD SHX Text

7)

AutoCAD SHX Text

6)

AutoCAD SHX Text

UNFINISHED CONCRETE CEILING OR UNISTRUT

AutoCAD SHX Text

3)

AutoCAD SHX Text

4)

AutoCAD SHX Text

1 3/16" (6)

AutoCAD SHX Text

M16 (6)

AutoCAD SHX Text

M12 (4)

AutoCAD SHX Text

SYSTEM CABLES

AutoCAD SHX Text

9)

AutoCAD SHX Text

CEILING PLATE, 1/2" THICK, SUPPLIED AND INSTALLED BY SIEMENS. MOUNTED FLUSH WITH THE INTERMEDIATE CEILING.

AutoCAD SHX Text

INTERFACE PLATE

AutoCAD SHX Text

SYSTEM CABLES

AutoCAD SHX Text

DROP CEILING

AutoCAD SHX Text

8)

AutoCAD SHX Text

6)

AutoCAD SHX Text

7)

AutoCAD SHX Text

MIN. 4" TO MAX. 3'-3 9/16"

AutoCAD SHX Text

IF L1 IS <1'-7 11/16": L2 = L1 - 3/16" L3 = L1 - 3 3/8" IF L1 IS >1'-7 11/16": L2 = L1 - 3/16" L3 = L1 - 5" L1 - 5" 2

AutoCAD SHX Text

L1: CEILING DISTANCE (DISTANCE BETWEEN CONCRETE CEILING AND INTERMEDIATE CEILING = TOTAL LENGTH OF SUBCONSTRUCTION. L2: REQUIRED LENGTH OF THREADED RODS L3: REQUIRED LENGTH OF SPACER SLEEVES

AutoCAD SHX Text

13/16" (6)

AutoCAD SHX Text

M16 (6)

AutoCAD SHX Text

10)

AutoCAD SHX Text

11)

AutoCAD SHX Text

12)

AutoCAD SHX Text

5)

AutoCAD SHX Text

2

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

4 8


08013

E-101ATTENTION:

RE

FE

RE

NC

E D

OC

UM

EN

T - N

OT

F

OR

C

ON

ST

RU

CT

IO

N

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

FOR CT GANTRY ONLY

AutoCAD SHX Text

MIN. 8'-6 3/8" MAX. 12'-1 1/16"

AutoCAD SHX Text

MINIMUM 7'-2 5/8"

AutoCAD SHX Text


AutoCAD SHX Text

AS NOTED

AutoCAD SHX Text

L. BACH

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

PROJECT #:

AutoCAD SHX Text

SHEET:

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

REF. #:

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

SHEET OF

AutoCAD SHX Text

DATE:

AutoCAD SHX Text

SHEET OF

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

N/A

AutoCAD SHX Text

TYPICAL REV 12

AutoCAD SHX Text

-ISSUE BLOCK-

AutoCAD SHX Text

DESCRIPTION

AutoCAD SHX Text

DATE

AutoCAD SHX Text

SYM

AutoCAD SHX Text

DEFINITION FLASH

AutoCAD SHX Text

REV 12

AutoCAD SHX Text

TRANSFORMER INSIDE THE HEAT EXCHANGER IS SUPPLIED BY SIEMENS, INSTALLED BY THE CUSTOMER/CONTRACTOR.

AutoCAD SHX Text

E-102

AutoCAD SHX Text

2

AutoCAD SHX Text

CONTROL ROOM

AutoCAD SHX Text

CT SCAN ROOM

AutoCAD SHX Text

ORIENTATION POINT

AutoCAD SHX Text

DOOR SWITCHES ARE OPTIONAL (PER LOCAL CODE REQUIREMENTS).

AutoCAD SHX Text

1

AutoCAD SHX Text

DEDICATED POWER SOURCE, SUPPLIED AND INSTALLED BY CUSTOMER/CONTRACTOR. SEE "POWER DIAGRAM".

AutoCAD SHX Text

CONDENSATION HOSE ROUTED ACCORDING TO LOCAL CODE TO SELECTED ON-SITE DRAIN.

AutoCAD SHX Text

A1

AutoCAD SHX Text

PDCA

AutoCAD SHX Text

PDCB

AutoCAD SHX Text

B

AutoCAD SHX Text

B1

AutoCAD SHX Text

EPO

AutoCAD SHX Text

MP

AutoCAD SHX Text

ICS

AutoCAD SHX Text

IES

AutoCAD SHX Text

IN2

AutoCAD SHX Text

IN3

AutoCAD SHX Text

IRS

AutoCAD SHX Text

3

AutoCAD SHX Text

3

AutoCAD SHX Text

EPO

AutoCAD SHX Text

4

AutoCAD SHX Text

6

AutoCAD SHX Text

7

AutoCAD SHX Text

8

AutoCAD SHX Text

9

AutoCAD SHX Text

10

AutoCAD SHX Text

13

AutoCAD SHX Text

14

AutoCAD SHX Text

18

AutoCAD SHX Text

19

AutoCAD SHX Text

F1

AutoCAD SHX Text

20

AutoCAD SHX Text

21

AutoCAD SHX Text

SPD

AutoCAD SHX Text

5

AutoCAD SHX Text

HD1

AutoCAD SHX Text

A2

AutoCAD SHX Text

S

AutoCAD SHX Text

S2

AutoCAD SHX Text

S1

AutoCAD SHX Text

EPO

AutoCAD SHX Text

2

AutoCAD SHX Text

11

AutoCAD SHX Text

22

AutoCAD SHX Text

23

AutoCAD SHX Text

24

AutoCAD SHX Text

25

AutoCAD SHX Text

16

AutoCAD SHX Text

DS

AutoCAD SHX Text

M-101-A

AutoCAD SHX Text

3

AutoCAD SHX Text

12

AutoCAD SHX Text

15

AutoCAD SHX Text

DC

AutoCAD SHX Text

23

AutoCAD SHX Text

VD1

AutoCAD SHX Text

17

AutoCAD SHX Text

POOR POWER WILL ALTER EQUIPMENT PERFORMANCE

AutoCAD SHX Text

POWER QUALITY

AutoCAD SHX Text

IT IS IN THE CUSTOMER'S INTEREST THAT THE ELECTRICAL CONTRACTOR BE RESPONSIBLE FOR TESTING AND VERIFYING THAT THE EQUIPMENT POWER SUPPLY COMPLIES WITH THE SIEMENS SPECIFICATIONS.

AutoCAD SHX Text

ELECTRICAL RACEWAY PLAN

AutoCAD SHX Text

SCALE: 1/4" = 1'-0"

AutoCAD SHX Text

SYSTEMS NETWORK (VERIFY WITH SMS PROJECT MANAGER).

AutoCAD SHX Text

ETHERNET CONNECTION TO CUSTOMER'S INFORMATION

AutoCAD SHX Text

ALL MAY NOT APPLY

AutoCAD SHX Text

UNDER FLOOR DUCT

AutoCAD SHX Text

CEILING DUCT

AutoCAD SHX Text

TRENCHDUCT

AutoCAD SHX Text

SYMBOLS

AutoCAD SHX Text

OPENING IN ACCESS FLOORING

AutoCAD SHX Text

(EPO) EMERGENCY POWER OFF BUTTON

AutoCAD SHX Text

DOOR SAFETY SWITCH

AutoCAD SHX Text

WARNING LIGHT (X-RAY ON)

AutoCAD SHX Text

VERTICAL DUCT

AutoCAD SHX Text

PULLBOX IN (FLOOR/WALL/CEILING)

AutoCAD SHX Text

OPENING IN RACEWAY OR TRENCHDUCT

AutoCAD SHX Text

MAIN PANEL OR ENCLOSURE BY CUSTOMER/CONTRACTOR

AutoCAD SHX Text

DS

AutoCAD SHX Text

110 VOLT, 20 AMP, HOSPITAL GRADE DUPLEX OUTLET UNLESS OTHERWISE STATED.

AutoCAD SHX Text

SURFACE DUCT

AutoCAD SHX Text

SPECIAL PURPOSE RECEPTACLE

AutoCAD SHX Text

L6-30R

AutoCAD SHX Text

110 VOLT, 20 AMP, HOSPITAL GRADE QUAD OUTLET

AutoCAD SHX Text

CONDUIT LENGTH CALCULATIONS

AutoCAD SHX Text

IF SITE SPECIFIC CONDITIONS EXCEED THE FOLLOWING ASSUMED VALUES THEN ADDITIONAL LENGTH MUST BE SUBTRACTED BY THE ELECTRICAL CONTRACTOR FROM THE MAXIMUM CONDUIT LENGTHS LISTED.

AutoCAD SHX Text

IF DUCT LOCATIONS ARE ALTERED FROM THE SHOWN LAYOUT IT IS THE ELECTRICAL CONTRACTORS RESPONSIBILITY TO RECALCULATE THE MAXIMUM CONDUIT LENGTHS.

AutoCAD SHX Text

ASSUMED VALUES USED IN CALCULATING STATED MAXIMUM CONDUIT LENGTHS: VERTICAL DUCTS - 10'-0" FLOOR PENETRATIONS - 3'-0"

AutoCAD SHX Text

ELECTRICAL NOTES

AutoCAD SHX Text

1) COMPLIANCE: ELECTRICAL WORK SHALL BE IN COMPLIANCE WITH THE NATIONAL ELECTRICAL CODE (NFPA-70), O.S.H.A. REGULATIONS, AS WELL AS APPLICABLE REGULATIONS OF CITY, COUNTY, STATE AND FEDERAL AGENCIES. PROVIDE MATERIALS AND EQUIPMENT THAT COMPLY WITH ANSI, IEEE AND NEMA STANDARDS AND ARE U.L. LISTED AND LABELED. THE CUSTOMER'S/CONTRACTOR'S WORK AND ALL EQUIPMENT INSTALLED SHALL COMPLY WITH THE CURRENT EDITION OF THE NATIONAL ELECTRICAL CODE ADOPTED/ENFORCED BY THE AUTHORITY HAVING JURISDICTION. 2) QUALITY ASSURANCE: THE CONTRACTOR SHALL VERIFY EXISTING CONDITIONS IN THE FIELD TO INSURE THAT THE NEW WORK WILL FIT INTO THE EXISTING STRUCTURE AS SHOWN ON THE DRAWINGS. SHOULD ANY CONDITIONS EXIST OR BE DISCOVERED THAT PREVENT THE INSTALLATION OF WORK AS SHOWN, THE CONTRACTOR SHALL NOTIFY THE OWNER'S REPRESENTATIVE PRIOR TO FABRICATION OF EQUIPMENT, OR THE PERFORMANCE OF ANY WORK THAT MAY BE AFFECTED. DO NOT ALTER DRAWINGS, DIMENSIONS, OR SPECIFICATIONS IN ANY WAY WITHOUT CONTACTING AND RECEIVING WRITTEN CONFIRMATION FROM SIEMENS PROJECT MANAGER. ALL DIMENSIONS ARE FROM FINISHED SURFACES. CONDUIT AND PULL BOXES TO BE INSTALLED BY THE CUSTOMER/CONTRACTOR WITH LOCATIONS BEING FIELD VERIFIED BY THE SIEMENS PROJECT MANAGER. 3) POWER SUPPLY SOURCE: POWER SUPPLIES FOR SIEMENS HEALTHCARE EQUIPMENT SHALL BE FROM A MEDICAL IMAGING PANEL OR BUILDING SERVICE EQUIPMENT THAT IS A GROUNDED 3 OR 4-WIRE 'WYE' SOURCE PER THE SPECIFIC EQUIPMENT OPERATION REQUIREMENTS. A DEDICATED CIRCUIT SHALL BE PROVIDED THAT IS KEPT ENTIRELY FREE AND INDEPENDENT OF ALL OTHER BUILDING WIRING. NO ELEVATORS, GENERATORS, PUMPS, HVAC OR SIMILAR EQUIPMENT SHALL BE CONNECTED TO THE SAME CIRCUIT OR MEDICAL IMAGING PANEL THAT SERVES THE SIEMENS HEALTHCARE EQUIPMENT. IF THE POWER SUPPLY SOURCE DOES NOT MEET THE SPECIFIC SIEMENS EQUIPMENT POWER REQUIREMENTS, THE CONTRACTOR SHALL PROVIDE THE NECESSARY EQUIPMENT REQUIRED TO ESTABLISH THE POWER SUPPLY IN ACCORDANCE WITH THE REQUIRED POWER SUPPLY PARAMETERS OF THE SIEMENS EQUIPMENT. THE CONTRACTOR SHALL COORDINATE THIS WORK WITH THE CUSTOMER AND/OR UTILITY COMPANY FIELD REPRESENTATIVE. 4) WORK FURNISHED BY CUSTOMER/CONTRACTOR: WORK NOT PROVIDED BY SIEMENS HEALTHCARE BUT SHOWN ON DRAWINGS TO BE FURNISHED AND INSTALLED BY CUSTOMER/CONTRACTOR INCLUDES, BUT IS NOT LIMITED TO, THE FOLLOWING, UNLESS NOTED OTHERWISE: ELECTRICAL RACEWAYS AND DUCTS, WIRING TROUGHS, PULL BOXES, CONDUITS, CIRCUIT BREAKERS, ACCESS PANELS, EMERGENCY OFF BUTTONS, DOOR SWITCHES, WARNING LIGHTS, WIRING, WIRING DEVICES, CONNECTORS, LIGHTING EQUIPMENT AND GROUNDING. 5) RACEWAY AND CONDUIT NOTES: ALL CONDUITS SHALL BE INSTALLED IN COMPLIANCE WITH THE CURRENT ENFORCED EDITION OF THE NATIONAL ELECTRICAL CODE. CONDUIT BODIES SHALL NOT BE USED. WHERE A CONDUIT ENTERS A BOX, FITTING, OR OTHER ENCLOSURE, AN INSULATED THROAT CONNECTOR SHALL BE PROVIDED TO PROTECT THE WIRE FROM ABRASION. ALL CONNECTORS FOR EMT SHALL BE COMPRESSION OR DOUBLE SET SCREW TYPE. KEEP RACEWAYS AT LEAST 6 INCHES AWAY FROM PARALLEL RUNS OF FLUES OR STEAM AND HOT WATER PIPES. INSTALL RACEWAY RUNS ABOVE WATER AND STEAM PIPES PROVIDED THAT CABLE RUN DISTANCES ARE MAINTAINED. USE TEMPORARY CLOSURES TO PREVENT FOREIGN MATTER FROM ENTERING RACEWAY. CONDUIT RUNS ARE SHOWN SCHEMATICALLY. INSTALL CONDUIT WITH A MINIMUM OF BENDS IN THE SHORTEST PRACTICAL DISTANCE CONSIDERING THE BUILDING CONSTRUCTION AND OBSTRUCTIONS, EXCEPT AS OTHERWISE INDICATED. THE CONTRACTOR SHALL MAKE CERTAIN THAT ANY CONDUIT/RACEWAY RUNS CONTAINING SIEMENS HEALTHCARE CABLES DO NOT EXCEED THE SPECIFIED MAXIMUM DISTANCES AS SHOWN ON THE ELECTRICAL DETAILS. LISTED CONDUIT SIZES FOR SIEMENS-SUPPLIED CABLES MUST BE MAINTAINED IN ORDER TO ENABLE THE TOTAL CABLE BUNDLE INCLUDING CONNECTORS TO BE PULLED THROUGH WITHOUT DAMAGE. PROVIDE ENCLOSED METAL WIRE DUCT RACEWAY SYSTEM WHERE SHOWN ON DRAWINGS WITH DIVIDERS TO SEPARATE THE DUCT INTO TWO OR THREE SEPARATE COMPARTMENTS AS SHOWN ON THE SIEMENS PLANS (FOR POWER AND SIEMENS HEALTHCARE CABLING). DIVIDERS AND CROSSOVER PIECES TO BE PROVIDED AS NECESSARY. THE CABLE TO CABLE AS WELL AS THE CIRCUIT TO CIRCUIT SEPARATION REQUIREMENT WAS EVALUATED DURING THE UL SYSTEM CERTIFICATION OF THE EQUIPMENT. ADDITIONAL SEPARATION OF THE SYSTEM CABLE ASSEMBLIES INTO SEPARATE OR PARTITIONED RACEWAYS, UNLESS OTHERWISE NOTED, IS NOT NECESSARY TO INSURE SEPARATION OF CIRCUITS. PROVIDE WIRE DUCT/RACEWAY WITH ACCESSIBLE REMOVABLE COVERS. LOCATIONS OF BUILDING MATERIAL OPENINGS (I.E. ACCESS PANELS) TO BE CUT IN FIELD ARE TO BE COORDINATED WITH THE DRAWING REQUIRMENTS AND BUILDING STRCTURE. THOSE THAT ARE NOT INDICATED OR INTERFER WITH BUILDING ELEMENTS SHALL BE COORDINATED WITH SIEMENS PROJECT MANAGER. ELECTRICAL PULL BOXES AND RACEWAY COVERS SHALL BE INSTALLED IN A MANNER TO ALLOW ACCESSIBILITY FOR INSTALLATION AND MAINTENANCE. CONTRACTORS MUST PROVIDE PULL STRINGS FOR ALL CONDUIT AND WIRE DUCT/RACEWAY. IN-FLOOR TRENCH DUCT AND FLUSH FLOOR BOXES SHALL BE PROVIDED WITH FULLY GASKETED REMOVABLE COVERS. WHEN JUNCTION BOXES AND WIRE DUCT/RACEWAY ARE MOUNTED HIGHER THAN 14 FEET ABOVE FINISHED FLOOR, THE ELECTRICAL CONTRACTOR SHALL PROVIDE TWO ELECTRICIANS TO HELP THE SIEMENS INSTALLERS PULL SIEMENS SUPPLIED CABLES AT CUSTOMER'S EXPENSE. WHEN JUNCTION WHEN JUNCTION BOXES AND WIRE DUCT/RACEWAY ARE MOUNTED ABOVE A HARD CEILING (I.E. SHEET ROCK), A 24" x 24" ACCESS PANEL IS REQUIRED AT EACH JUNCTION BOX AND WITHIN 2 FEET OF EACH RACEWAY TRANSITION (SUCH AS A 90 DEGREE ELBOW OR TEE) IN DUCT/RACEWAY. THERE MUST BE FREE AND CLEAR ACCESS TO JUNCTION BOXES AND WIRE DUCT/RACEWAY. WHEN ACCESS PANELS ARE LOCATED MORE THAN 3 FEET FROM JUNCTION BOXES AND WIRE DUCT/RACEWAY THE ELECTRICAL CONTRACTOR SHALL PROVIDE TWO ELECTRICIANS TO HELP SIEMENS INSTALLERS PULL SIEMENS SUPPLIED CABLES AT CUSTOMER'S EXPENSE. 6) WIRING: ALL WIRING INSTALLED SHALL BE 600 VOLT CLASS, STRANDED TYPE THHN/THWN-2, SINGLE CONDUCTOR ANNEALED COPPER FOR A MAXIMUM OPERATING TEMPERATURE OF 90° C (194° F), SIZED AS INDICATED, INSTALLED IN METAL RACEWAYS. THE CUSTOMER/CONTRACTOR SHALL LEAVE A MINIMUM 10 FEET OF WIRE TAILS AT ALL OUTLET POINTS WITH WIRE IDENTIFICATION TAGGED AT BOTH ENDS FOR FINAL CONNECTION BY THE CUSTOMER/ELECTRICAL CONTRACTOR. 7) SHORT CIRCUIT REQUIREMENTS: ALL CIRCUIT BREAKERS SUPPLIED FOR THE SIEMENS EQUIPMENT REQUIREMENTS SHALL BE RATED HIGHER THAN THE SHORT CIRCUIT AVAILABLE AT THE TERMINALS OF THE ELECTRICAL EQUIPMENT AS DETERMINED BY THE ENGINEER OF RECORD, BUT NOT LESS THAN 35,000A RMS SYMMETRICAL AT 480V, 3-PHASE, 60 HERTZ. THE CONTRACTOR SHALL OBTAIN THE CORRECT SHORT CIRCUIT CURRENT RATING OF ALL THE NEW EQUIPMENT FOR INSTALLATION FROM THE ENGINEER OF RECORD.

AutoCAD SHX Text

ELECTRICAL LEGEND

AutoCAD SHX Text

SYM

AutoCAD SHX Text

SIZE

AutoCAD SHX Text

DESCRIPTION

AutoCAD SHX Text

REMARKS

AutoCAD SHX Text

SUPPLIED AND INSTALLED BY CUSTOMER/CONTRACTOR

AutoCAD SHX Text

A1

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

PULL BOX MOUNTED FLUSH WITH FINISHED WALL AT FLOOR LINE IN SHOWN LOCATION.

AutoCAD SHX Text

A2

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

PULL BOX MOUNTED FLUSH WITH FINISHED WALL AT FLOOR LINE IN SHOWN LOCATION.

AutoCAD SHX Text

B

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

PULL BOX MOUNTED BELOW FLOOR SLAB WITH A 3 1/2" CORE DRILL WITH SLEEVE AND A 3" CORE DRILL WITH SLEEVE THROUGH THE SLAB ENDING FLUSH WITH THE FINISHED FLOOR IN SHOWN LOCATIONS.

AutoCAD SHX Text

GANTRY CABLE ACCESS

AutoCAD SHX Text

B1

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

PULL BOX MOUNTED BELOW FLOOR SLAB WITH A 5" CORE DRILL WITH SLEEVE THROUGH THESLAB ENDING FLUSH WITH THE FINISHED FLOOR IN SHOWN LOCATION.

AutoCAD SHX Text

GANTRY CABLE ACCESS

AutoCAD SHX Text

DC

AutoCAD SHX Text

---

AutoCAD SHX Text

DISCONNECT SWITCH MOUNTED NEAR OUTDOOR UNIT TO DISCONNECT POWER SUPPLY FROM INDOOR UNIT. SUPPLIED BY SIEMENS, INSTALLED BY CUSTOMER/CONTRACTOR IN ACCORDANCE WITH LOCAL CODES.

AutoCAD SHX Text

OUTDOOR UNIT-WATER/AIR SPLIT

AutoCAD SHX Text

EPO

AutoCAD SHX Text

---

AutoCAD SHX Text

EMERGENCY POWER OFF BUTTON. EXACT LOCATIONS TO BE DETERMINED BY CUSTOMER/CONTRACTOR.

AutoCAD SHX Text

SEE POWER SCHEDULE

AutoCAD SHX Text

F1

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

PULL BOX MOUNTED ABOVE FINISHED CEILING.

AutoCAD SHX Text

CARE VISION MONITOR CEILING MOUNT

AutoCAD SHX Text

ICS

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

PULL BOX MOUNTED BELOW FLOOR SLAB WITH 4" CORE DRILL WITH SLEEVE THROUGH SLABENDING FLUSH WITH FINISHED FLOOR IN SHOWN LOCATION.

AutoCAD SHX Text

IMAGE CONSTRUCTION SYS.

AutoCAD SHX Text

IES

AutoCAD SHX Text

---

AutoCAD SHX Text

FIXED POINT DESIGNATION, SAME PULL BOX/OPENING AS ICS.

AutoCAD SHX Text

IMAGE EVALUATION SYSTEM

AutoCAD SHX Text

IN2

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

PULL BOX MOUNTED FLUSH WITH FINISHED WALL AT FLOORLINE IN CONTROL AREA.

AutoCAD SHX Text

INJECTOR ELECTRONICS

AutoCAD SHX Text

IN3

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

PULL BOX MOUNTED ABOVE FINISHED CEILING IN SHOWN LOCATION.

AutoCAD SHX Text

CEILING MTD. INJECTOR

AutoCAD SHX Text

IRS

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

PULL BOX MOUNTED TO UNDERSIDE OF FLOOR SLAB WITH 4" CORE DRILL WITH SLEEVETHROUGH FLOOR SLAB ENDING FLUSH WITH FINISHED FLOOR IN SHOWN LOCATION.

AutoCAD SHX Text

IMAGE RECONSTRUCTION CAB.

AutoCAD SHX Text

MP

AutoCAD SHX Text

---

AutoCAD SHX Text

MAIN PANEL WITH MAIN BREAKER. EXACT LOCATION DETERMINED BY CUSTOMER/CONTRACTOR.

AutoCAD SHX Text

SEE POWER SCHEDULE.

AutoCAD SHX Text

PDCA

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text


AutoCAD SHX Text

POWER DISTRIBUTION CAB.

AutoCAD SHX Text

PDCB

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text


AutoCAD SHX Text

POWER DISTRIBUTION CAB.

AutoCAD SHX Text

S

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

TWO PULL BOXES MOUNTED BELOW THE FLOOR SLAB WITH TWO 6" CORE DRILLS WITH SLEEVESTHROUGH THE FLOOR SLAB ENDING FLUSH WITH FINISHED FLOOR IN SHOWN LOCATIONS.

AutoCAD SHX Text

HEAT EXCHANGER CABINET-WATER/AIR SPLIT

AutoCAD SHX Text

S1

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

PULL BOX THAT IS PROVIDED ON THE OUTDOOR COOLING UNIT.

AutoCAD SHX Text

OUTDOOR COOLING UNIT-WATER/AIR SPLIT

AutoCAD SHX Text

S2

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

PULL BOX MOUNTED ADJACENT TO OUTDOOR COOLING UNIT PROVIDED WITH FLEX-TITE CONDUIT FROM PULL BOX TO WATER HOSE CONNECTIONS ON OUTDOOR COOLING UNIT.

AutoCAD SHX Text

OUTDOOR COOLING UNIT- WATER/AIR SPLIT

AutoCAD SHX Text

SPD

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

PULL BOX MOUNTED FLUSH WITH FINISHED WALL PROVIDED WITH 2" OPENING IN FINISHEDCOVER. THE SURGE PROTECTIVE DEVICE MUST BE LOCATED WITHIN 3 FEET CABLE RUN FROM CIRCUIT BREAKER, AT HEIGHT DETERMINED BY CUSTOMER/ CONTRACTOR.

AutoCAD SHX Text

SEE DETAIL S-101

AutoCAD SHX Text

HD1

AutoCAD SHX Text

10" x 3 1/2"

AutoCAD SHX Text

ELECTRICAL DUCT RUN HORIZONTALLY ON THE WALL AT THE FLOOR LINE AND SURFACE MOUNTED ON FINISHED WALL AS SHOWN FOR EXCESS CABLE STORAGE.

AutoCAD SHX Text

RACEWAY

AutoCAD SHX Text

VD1

AutoCAD SHX Text

10" x 3 1/2"

AutoCAD SHX Text

ELECTRICAL DUCT MOUNTED FLUSH WITH FINISHED WALL IN SHOWN LOCATION PROVIDED WITH FINISHED, REMOVABLE COVERS. TO EXTEND FROM FLOOR LINE TO END ABOVE FINISHED CEILING. DUCT TO BE DIVIDED INTO TWO SECTIONS WITH METAL DIVIDERS.

AutoCAD SHX Text

RACEWAY

AutoCAD SHX Text

CONTRACTOR SUPPLIED CABLES

AutoCAD SHX Text

FROM

AutoCAD SHX Text

VIA

AutoCAD SHX Text

TO

AutoCAD SHX Text

DESCRIPTION

AutoCAD SHX Text

REMARKS

AutoCAD SHX Text

POWER SOURCE

AutoCAD SHX Text

1

AutoCAD SHX Text

MP

AutoCAD SHX Text

3-PHASE CONDUCTORS, 1 NEUTRAL, 1 GROUND ALL TO BE THE SAME SIZE. SIZED BY ELECTRICAL ENGINEER OF RECORD.

AutoCAD SHX Text

SEE POWER SCHEDULE

AutoCAD SHX Text

MP

AutoCAD SHX Text

2

AutoCAD SHX Text

EPO

AutoCAD SHX Text

DETERMINED BY ELECTRICAL ENGINEER OF RECORD.

AutoCAD SHX Text

SEE POWER SCHEDULE

AutoCAD SHX Text

EPO

AutoCAD SHX Text

3

AutoCAD SHX Text

EPO

AutoCAD SHX Text


AutoCAD SHX Text

SEE POWER SCHEDULE

AutoCAD SHX Text

EPO

AutoCAD SHX Text

4,VD1

AutoCAD SHX Text

PDCA

AutoCAD SHX Text


AutoCAD SHX Text

SEE POWER SCHEDULE

AutoCAD SHX Text

MP

AutoCAD SHX Text

5

AutoCAD SHX Text

SPD

AutoCAD SHX Text

3-PHASE CONDUCTORS, 1 NEUTRAL AND 1 GROUND ALL TO BE THE SAME SIZE. SIZED BY ELECTRICAL ENGINEER OF RECORD.

AutoCAD SHX Text

SEE POWER SCHEDULE

AutoCAD SHX Text

MP

AutoCAD SHX Text

6,VD1

AutoCAD SHX Text

PDCA

AutoCAD SHX Text

3 PHASE CONDUCTORS, 1 NEUTRAL AND 1 GROUND ALL TO BE THE SAME SIZE, MAX. 3/0. SIZED BY ELECTRICAL ENGINEER OF RECORD.

AutoCAD SHX Text

SEE POWER SCHEDULE

AutoCAD SHX Text

MP

AutoCAD SHX Text

7,A1

AutoCAD SHX Text

PDCB

AutoCAD SHX Text

3 PHASE CONDUCTORS, 1 NEUTRAL AND 1 GROUND ALL TO BE THE SAME SIZE, MAX. 3/0. SIZED BY ELECTRICAL ENGINEER OF RECORD.

AutoCAD SHX Text

SEE POWER SCHEDULE

AutoCAD SHX Text

PDCA

AutoCAD SHX Text

VD1,8

AutoCAD SHX Text

WARNING LIGHT

AutoCAD SHX Text


AutoCAD SHX Text

PDCA

AutoCAD SHX Text

VD1,9

AutoCAD SHX Text

DS

AutoCAD SHX Text


AutoCAD SHX Text

MP

AutoCAD SHX Text

22,A2

AutoCAD SHX Text

S

AutoCAD SHX Text

3 PHASE CONDUCTORS AND 1 GROUND ALL TO BE THE SAME SIZE. SIZED BY ELECTRICAL ENGINEER OF RECORD.

AutoCAD SHX Text

SEE POWER SCHEDULE

AutoCAD SHX Text

SIEMENS SUPPLIED CABLES

AutoCAD SHX Text

FROM

AutoCAD SHX Text

VIA

AutoCAD SHX Text

TO

AutoCAD SHX Text

DESCRIPTION

AutoCAD SHX Text

REMARKS

AutoCAD SHX Text

PDCA

AutoCAD SHX Text

10

AutoCAD SHX Text

ICS

AutoCAD SHX Text

POWER CABLE; W8:300V, W34:600V DATA CABLE; W61:CAT5 ,W63:CAT 5

AutoCAD SHX Text

MAXIMUM LENGTH 82'-0"

AutoCAD SHX Text

PDCA

AutoCAD SHX Text

11

AutoCAD SHX Text

IRS

AutoCAD SHX Text

POWER CABLE; W7:300V, W33:600V DATA CABLE; W57:CAT5, W65:CAT5

AutoCAD SHX Text


AutoCAD SHX Text

PDCA

AutoCAD SHX Text

ROUTE UNDER CABINETS

AutoCAD SHX Text

PDCB

AutoCAD SHX Text

POWER CABLE & CONTROL CABLE; W11:300V, W55:300V

AutoCAD SHX Text


AutoCAD SHX Text

PDCA

AutoCAD SHX Text

12

AutoCAD SHX Text

B

AutoCAD SHX Text

POWER CABLE; W1:600V, W2:600V, W3:300V, W4:2000V, W9:300V, W54:300V PE CABLE & CONTROL CABLE; W30:600V, W59:600V DATA CABLE; W53:CAT5, W74:FIBER

AutoCAD SHX Text


AutoCAD SHX Text

PDCB

AutoCAD SHX Text

13,14

AutoCAD SHX Text

B

AutoCAD SHX Text

POWER CABLE; W5:2000V PE CABLE AND DATA CABLE; W36:600V, W76:FIBER

AutoCAD SHX Text


AutoCAD SHX Text

B

AutoCAD SHX Text

15

AutoCAD SHX Text

ICS

AutoCAD SHX Text

CONTROL CABLE; W51:300V

AutoCAD SHX Text


AutoCAD SHX Text

B

AutoCAD SHX Text

16

AutoCAD SHX Text

IRS

AutoCAD SHX Text

DATA CABLE; W70:FIBER, W78:FIBER, W98:FIBER

AutoCAD SHX Text


AutoCAD SHX Text

S

AutoCAD SHX Text

17

AutoCAD SHX Text

B1

AutoCAD SHX Text

WATER HOSES

AutoCAD SHX Text


AutoCAD SHX Text

B1

AutoCAD SHX Text

18

AutoCAD SHX Text

DRAIN

AutoCAD SHX Text

CONDENSATION HOSE

AutoCAD SHX Text


AutoCAD SHX Text

IN2

AutoCAD SHX Text

19

AutoCAD SHX Text

IN3

AutoCAD SHX Text

INJECTOR CABLE

AutoCAD SHX Text

ICS

AutoCAD SHX Text

20

AutoCAD SHX Text

F1

AutoCAD SHX Text

CONTROL CABLE

AutoCAD SHX Text


AutoCAD SHX Text

PDCA

AutoCAD SHX Text

VD1,21

AutoCAD SHX Text

F1

AutoCAD SHX Text

POWER CABLE

AutoCAD SHX Text


AutoCAD SHX Text

S

AutoCAD SHX Text

A2,23,DC,23

AutoCAD SHX Text

S1

AutoCAD SHX Text

POWER CABLE AND CONTROL CABLE; W820:600V

AutoCAD SHX Text

MAXIMUM LENGTH 131'-0" SUPPLIED BY SIEMENS, INSTALLED BY CUSTOMER/CONTRACTOR

AutoCAD SHX Text

S

AutoCAD SHX Text

24

AutoCAD SHX Text

B

AutoCAD SHX Text

DATA CABLE; W821:30V

AutoCAD SHX Text


AutoCAD SHX Text

S

AutoCAD SHX Text

25

AutoCAD SHX Text

S2

AutoCAD SHX Text

WATER HOSES

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

5 8


08013

E-102ATTENTION:

RE

FE

RE

NC

E D

OC

UM

EN

T - N

OT

F

OR

C

ON

ST

RU

CT

IO

N

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

FOR CT GANTRY ONLY

AutoCAD SHX Text

MIN. 8'-6 3/8" MAX. 12'-1 1/16"

AutoCAD SHX Text

MINIMUM 7'-2 5/8"

AutoCAD SHX Text


AutoCAD SHX Text

AS NOTED

AutoCAD SHX Text

L. BACH

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

PROJECT #:

AutoCAD SHX Text

SHEET:

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

REF. #:

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

SHEET OF

AutoCAD SHX Text

DATE:

AutoCAD SHX Text

SHEET OF

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

N/A

AutoCAD SHX Text

TYPICAL REV 12

AutoCAD SHX Text

-ISSUE BLOCK-

AutoCAD SHX Text

DESCRIPTION

AutoCAD SHX Text

DATE

AutoCAD SHX Text

SYM

AutoCAD SHX Text

DEFINITION FLASH

AutoCAD SHX Text

REV 12

AutoCAD SHX Text

E-102

AutoCAD SHX Text

1

AutoCAD SHX Text

EQUIPMENT ROOM

AutoCAD SHX Text

CT SCAN ROOM

AutoCAD SHX Text

CONTROL ROOM

AutoCAD SHX Text

ORIENTATION POINT

AutoCAD SHX Text

B1

AutoCAD SHX Text

IN3

AutoCAD SHX Text

B

AutoCAD SHX Text

PDCA

AutoCAD SHX Text

S

AutoCAD SHX Text

A2

AutoCAD SHX Text

A1

AutoCAD SHX Text

IRS

AutoCAD SHX Text

PDCB

AutoCAD SHX Text

IES

AutoCAD SHX Text

ICS

AutoCAD SHX Text

F1

AutoCAD SHX Text

IN2

AutoCAD SHX Text

HD1

AutoCAD SHX Text

VD1

AutoCAD SHX Text

ELECTRICAL DIMENSION PLAN

AutoCAD SHX Text

SCALE: 1/4" = 1'-0"

AutoCAD SHX Text

REV 4

AutoCAD SHX Text

ALL CONDUITS AND WIRES SIZES MUST BE DETERMINED BY THE ELECTRICAL ENGINEER OF RECORD PER N.E.C AND TO MAINTAIN SIEMENS IMPEDANCE REQUIREMENTS.

AutoCAD SHX Text

POWER SCHEDULE

AutoCAD SHX Text

ITEM

AutoCAD SHX Text

QTY

AutoCAD SHX Text

DESCRIPTION

AutoCAD SHX Text

EPO

AutoCAD SHX Text

VARIES

AutoCAD SHX Text

A

AutoCAD SHX Text

1

AutoCAD SHX Text

BREAKER AMPS: 125 (FOR POWER DISTRIBUTION CABINETS (FOR POWER DISTRIBUTION CABINETS "PDCA" & "PDCB")

AutoCAD SHX Text

D

AutoCAD SHX Text

1

AutoCAD SHX Text

BREAKER AMPS: 30 (FOR SURGE PROTECTIVE DEVICE "SPD")(FOR SURGE PROTECTIVE DEVICE "SPD")

AutoCAD SHX Text

VOLTS

AutoCAD SHX Text

480/277Y

AutoCAD SHX Text

3

AutoCAD SHX Text

PHASES

AutoCAD SHX Text

NEUTRAL

AutoCAD SHX Text

GROUND

AutoCAD SHX Text

TOTAL WIRES

AutoCAD SHX Text

1

AutoCAD SHX Text

1

AutoCAD SHX Text

5

AutoCAD SHX Text

VOLTS

AutoCAD SHX Text

480/277Y

AutoCAD SHX Text

3

AutoCAD SHX Text

PHASES

AutoCAD SHX Text

NEUTRAL

AutoCAD SHX Text

GROUND

AutoCAD SHX Text

TOTAL WIRES

AutoCAD SHX Text

1

AutoCAD SHX Text

1

AutoCAD SHX Text

5

AutoCAD SHX Text

EPO

AutoCAD SHX Text

NC

AutoCAD SHX Text

NC

AutoCAD SHX Text

NC

AutoCAD SHX Text

MAIN BREAKER EPO CIRCUIT POWER SOURCE

AutoCAD SHX Text

NOTE #2

AutoCAD SHX Text

EPO

AutoCAD SHX Text

EPO

AutoCAD SHX Text

NOTE #1

AutoCAD SHX Text

NOTE 1 - EPO CIRCUIT #1 MAIN CIRCUIT BREAKER EMERGENCY POWER OFF BUTTON WITH PROTECTIVE COVER THAT PREVENTS ACCIDENTAL ACTIVATION. THE EPO MUST BE OF FAIL-SAFE DESIGN. ALL EPO'S TO HAVE MECHANICAL LATCHING MECHANISM. MECHANICAL LATCHING MECHANISM. . EPO MUST BE RESET BEFORE MAIN BREAKER CAN RESUME OPERATION. CONTACTS AND WIRING CONFIGURATION TO BE DESIGNED BY ELECTRICAL ENGINEER OF RECORD. NOTE 2 - EPO CIRCUIT #2 EPO CONTACTS TO BE NORMALLY CLOSED, WIRED IN NORMALLY CLOSED, WIRED IN , WIRED IN SERIES, CONNECTED TO CT PDC UPS ONLY. THE EPOs MUST BE INSTALLED BY A QUALIFIED ELECTRICAL CONTRACTOR ACCORDING TO NATIONAL ELECTRICAL CODE, STATE AND LOCAL REGULATIONS. MEASURES SHOULD BE TAKEN TO DESIGN THE CIRCUIT IN SUCH A WAY THAT IT WILL ALWAYS WORK WHEN THE MEDICAL EQUIPMENT IS POWERED. THE CUSTOMER IS SOLELY RESPONSIBLE FOR THE IMPLEMENTATION OF THE EPOs AND THEIR ASSOCIATED CIRCUITS AND MUST MAKE THE FINAL DETERMINATION CONSIDERING ALL SITE CONDITIONS AND REGULATORY FACTORS.

AutoCAD SHX Text

SURGE PROTECTIVE DEVICE

AutoCAD SHX Text

POWER DISTRIBUTION CABINET A

AutoCAD SHX Text

UPS

AutoCAD SHX Text

M

AutoCAD SHX Text

MP

AutoCAD SHX Text

A (125A) (125A)

AutoCAD SHX Text

B (125A) (125A)

AutoCAD SHX Text

PDCA

AutoCAD SHX Text

SPD

AutoCAD SHX Text

C (30A) (30A)

AutoCAD SHX Text

M

AutoCAD SHX Text

1

AutoCAD SHX Text

MAIN BREAKER AMPS: SEE POWER REQUIREMENTS

AutoCAD SHX Text

VOLTS

AutoCAD SHX Text

480/277Y

AutoCAD SHX Text

3

AutoCAD SHX Text

PHASES

AutoCAD SHX Text

NEUTRAL

AutoCAD SHX Text

GROUND

AutoCAD SHX Text

TOTAL WIRES

AutoCAD SHX Text

1

AutoCAD SHX Text

1

AutoCAD SHX Text

5

AutoCAD SHX Text

MAIN BREAKER MUST HAVE TRIPPING DEVICE SO WHEN ANY EPO IS PRESSED THE BREAKER TRIPS.

AutoCAD SHX Text

MP

AutoCAD SHX Text

1

AutoCAD SHX Text

MAIN PANEL WITH CIRCUIT BREAKERS FLUSH OR SURFACE MOUNTED.

AutoCAD SHX Text

(THIS BREAKER WILL NOT BE NEEDED IF THE SURGE PROTECTIVE DEVICE IS NOT PURCHASED.)

AutoCAD SHX Text

POWER DISTRIBUTION CABINET B

AutoCAD SHX Text

PDCB

AutoCAD SHX Text

B

AutoCAD SHX Text

1

AutoCAD SHX Text

INDOOR HEAT EXCHANGER

AutoCAD SHX Text

S

AutoCAD SHX Text

D (30A)(30A)

AutoCAD SHX Text

C

AutoCAD SHX Text

1

AutoCAD SHX Text

BREAKER AMPS: 30 (FOR INDOOR HEAT EXCHANGER "S")(FOR INDOOR HEAT EXCHANGER "S")

AutoCAD SHX Text

VOLTS

AutoCAD SHX Text

480/277Y

AutoCAD SHX Text

3

AutoCAD SHX Text

PHASES

AutoCAD SHX Text

NEUTRAL

AutoCAD SHX Text

GROUND

AutoCAD SHX Text

TOTAL WIRES

AutoCAD SHX Text

0

AutoCAD SHX Text

1

AutoCAD SHX Text

4

AutoCAD SHX Text

UNLESS OTHERWISE NOTED, ALL ITEMS LISTED IN THIS SCHEDULE SHALL BE SUPPLIED AND INSTALLED BY CUSTOMER/CONTRACTOR.

AutoCAD SHX Text

480/277Y VOLTS 3 PHASE, 4 WIRE PLUS GROUND

AutoCAD SHX Text

PHASE AND NEUTRAL WIRES TO BE THE SAME SIZE, GROUND PER NEC. UNLESS OTHERWISE NOTED ALL BREAKERS WILL BE 80% RATED.

AutoCAD SHX Text

5" CORE DRILLTHROUGH FLOOR SLAB FOR WATER HOSES.

AutoCAD SHX Text

3" CORE DRILLTHROUGH FLOOR SLAB FOR DATA CABLES.

AutoCAD SHX Text

3 1/2" COREDRILL THROUGH FLOOR SLAB FOR POWER CABLES.

AutoCAD SHX Text

GANTRY OPENINGS

AutoCAD SHX Text

PULL BOX MOUNTED BELOW FLOOR SLAB.

AutoCAD SHX Text

PULL BOX MOUNTED BELOW FLOOR SLAB.

AutoCAD SHX Text

TABLE SIDE

AutoCAD SHX Text

PLAN VIEW OF GANTRY CABLE INLETS

AutoCAD SHX Text

IMPORTANT ALL CONDUITS MUST HAVE STANDARD SWEEP ELBOWS

AutoCAD SHX Text

ORIENTATION POINT

AutoCAD SHX Text

NO FLOOR PENETRATIONS PERMITTED WITHIN THIS DEFINED AREA (7 1/2" ) AROUND THEADJUSTABLE FEET. (VALID FOR ALL FEET)

AutoCAD SHX Text

GANTRY ADJUSTABLE FEET AND MOUNTING HOLE LOCATIONS. SEE DETAIL 1 ON S-101 SHEET FOR SPECIFIC LOCATIONS.

AutoCAD SHX Text

SCALE: 1"=1'-0"

AutoCAD SHX Text

1

AutoCAD SHX Text

NORMALLY OPEN

AutoCAD SHX Text

24 VAC

AutoCAD SHX Text

RELAY (1)

AutoCAD SHX Text

NEUTRAL

AutoCAD SHX Text

LIGHTING PANEL

AutoCAD SHX Text

BY CUSTOMER/CONTRACTOR

AutoCAD SHX Text

HOT

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

NONE

AutoCAD SHX Text

AUXILIARY WIRING

AutoCAD SHX Text

DS

AutoCAD SHX Text

SUPPLIED 24 VOLTS (FOR DOOR SWITCH ONLY)

AutoCAD SHX Text

LIGHTING PANEL TO BE PROVIDED WITH SWITCH TO TURN OFF WARNING LIGHTS FOR SERVICE PURPOSES.

AutoCAD SHX Text

1) RELAY WITH A 24 VOLT, AC COIL (NOT TO EXCEED 5 AMPS) SUPPLIED BY ELECTRICAL CONTRACTOR. ALL ITEMS EXTERNAL TO THE SIEMENS CABINET ARE TO BE SUPPLIED AND INSTALLED BY CONTRACTOR.

AutoCAD SHX Text

INCANDESCENT/FLUORESCENT/LED "X-RAY ON" WARNING LIGHT

AutoCAD SHX Text

ABOVE ROOM ENTRY DOOR OUTSIDE SCAN ROOM

AutoCAD SHX Text

6 FT. PIGTAILS

AutoCAD SHX Text

SIEMENS POWER DISTRIBUTION CABINET (PDC) OR LINE CONNECTION BOX (LCB)

AutoCAD SHX Text

X-RAY WARNING LIGHTS AND DOOR SWITCH SCHEMATIC

AutoCAD SHX Text

2

AutoCAD SHX Text

EQUIPMENT GROUND CONDUCTOR TO COMPLY WITH THE FOLLOWING: 1) SIZED EQUIVALENT TO THE PHASE CONDUCTORS (FULL SIZED GROUND). 2) DERIVED FROM THE ELECTRICAL SERVICE, TRANSFORMER OR MAIN DISTRIBUTION PANEL FEEDING THE SIEMENS EQUIPMENT. 3) RUN IN THE SAME CONDUIT, TROUGH OR RACEWAY AS THE PHASE CONDUCTORS. 4) CONTINUOUS, WITH NO BREAKS OR USE OF CONDUIT, CHASSIS OR EARTH AS THE SOLE GROUNDING PATH. 5) BONDED TO CHASSIS AND/OR CONDUIT IN ACCORDANCE WITH THE NEC REQUIREMENTS. 6) MINIMIZE CONNECTIONS OR TERMINALS TO ENSURE CONTINUITY OVER THE LIFE OF THE INSTALLATION. 7) AS A NORM, THERE SHOULD NOT BE ANY CURRENT PRESENCE ON THE GROUND CONDUCTOR, BUT IT IS ACCEPTABLE TO HAVE <500mA DURING OPERATION OF THE <500mA DURING OPERATION OF THE 500mA DURING OPERATION OF THE DURING OPERATION OF THE IMAGING EQUIPMENT.

AutoCAD SHX Text

GROUNDING NOTES

AutoCAD SHX Text

POWER REQUIREMENTS

AutoCAD SHX Text

SYSTEM

AutoCAD SHX Text


AutoCAD SHX Text

POWER CONSUMPTION (WITH STANDARD HOSPITAL CHILLED WATER) CT OPERATING FOR 2 SEC - 283 kVA CT OPERATING AT 35 SEC - 177 kVA CT OPERATING AT 100 SEC - 85 kVA CT SYSTEM ON (STAND-BY) - 6 kVA CT SYSTEM ON (COMP ON) - 3 kVA CT GANTRY OFF (EVA ON) - 1 kVA

AutoCAD SHX Text

ALL STANDARD COMPONENTS AND ADD-ONS ARE SUPPLIED VIA THE POWER DISTRIBUTION SYSTEM.

AutoCAD SHX Text

DO NOT CONNECT NON-SIEMENS COMPONENTS SUCH AS LASER CAMERAS OR FILM PROCESSORS TO THE SIEMENS POWER DISTRIBUTION SYSTEM (PDS).

AutoCAD SHX Text

THE EXAMINATION ROOM SHOULD BE EQUIPPED WITH AT LEAST ONE EMERGENCY POWER OFF (PANIC) BUTTON.

AutoCAD SHX Text

IF AN ON-SITE TRANSFORMER IS REQUIRED TO OBTAIN CT OPERATING VOLTAGE, IT MUST BE OF SUFFICIENT CAPACITY AND CHARACTERISTICS TO MAINTAIN SUPPLY VOLTAGE AND IMPEDENCE REQUIREMENTS (TRANSFORMER AND CONDUCTORS).

AutoCAD SHX Text

TO ENSURE SATISFACTORY SYSTEM OPERATION THE PDS MUST HAVE A DEDICATED PROTECTIVE GROUND CONDUCTOR.

AutoCAD SHX Text

POWER CONSUMPTION (WITH OPTIONAL WATER/AIR SPLIT COOLING SYSTEM) CT OPERATING FOR 2 SEC - 283 kVA CT OPERATING AT 35 SEC - 177 kVA CT OPERATING AT 100 SEC - 85 kVA CT SYSTEM ON (STAND-BY) - 6 kVA CT SYSTEM ON (COMP ON) - 3 kVA CT GANTRY OFF (EVA ON) - 1 kVA COOLING SYSTEM - 10kVA COOLING SYSTEM FLOW HEATER (OPTIONAL) - 12kVA

AutoCAD SHX Text

SUPPLY VOLTAGE (VOLTS)

AutoCAD SHX Text

3 480±10%

AutoCAD SHX Text

POWER CONSUMPTION (kVA)

AutoCAD SHX Text

SUPPLY IMPEDANCE (mΩ)

AutoCAD SHX Text

SEE BELOW

AutoCAD SHX Text

MAIN CIRCUIT BREAKER (AMPS)

AutoCAD SHX Text

225

AutoCAD SHX Text

65

AutoCAD SHX Text

CONDUIT LEGEND

AutoCAD SHX Text

SYM

AutoCAD SHX Text

SIZE

AutoCAD SHX Text

DESCRIPTION

AutoCAD SHX Text

REMARKS

AutoCAD SHX Text

SUPPLIED AND INSTALLED BY CUSTOMER/CONTRACTOR

AutoCAD SHX Text

1

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

CONDUIT FROM POWER SOURCE TO "MP" SIZED BY ELECTRICAL ENGINEER OF RECORD.

AutoCAD SHX Text

SEE POWER SCHEDULE

AutoCAD SHX Text

2

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

CONDUIT FROM "MP" TO "EPO" SIZED BY ELECTRICAL ENGINEER OF RECORD.

AutoCAD SHX Text

SEE POWER SCHEDULE

AutoCAD SHX Text

3

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

CONDUIT FROM "EPO" TO "EPO" SIZED BY ELECTRICAL ENGINEER OF RECORD.

AutoCAD SHX Text

SEE POWER SCHEDULE

AutoCAD SHX Text

4

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

CONDUIT FROM "EPO" TO "VD1" (PDCA/UPS), SIZED BY ELECTRICAL ENGINEER OF RECORD.

AutoCAD SHX Text

SEE POWER SCHEDULE

AutoCAD SHX Text

5

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

CONDUIT FROM "MP" TO "SPD" SIZED BY ELECTRICAL ENGINEER OF RECORD.

AutoCAD SHX Text

SEE POWER SCHEDULE

AutoCAD SHX Text

6

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

CONDUIT FROM "MP" TO "VD1" (PDCA), SIZED BY ELECTRICAL ENGINEER OF RECORD.

AutoCAD SHX Text

SEE POWER SCHEDULE

AutoCAD SHX Text

7

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

CONDUIT FROM "MP" TO "A1" (PDCB), SIZED BY ELECTRICAL ENGINEER OF RECORD.

AutoCAD SHX Text

SEE POWER SCHEDULE

AutoCAD SHX Text

8

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

CONDUIT FROM "VD1" (PDCA) TO "WARNING LIGHT".

AutoCAD SHX Text

9

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

CONDUIT FROM "VD1" (PDCA) TO "DS".

AutoCAD SHX Text

10

AutoCAD SHX Text

2-1/2"%%c

AutoCAD SHX Text

CONDUIT FROM "PDCA" TO "ICS".

AutoCAD SHX Text

MAX. CONDUIT LENGTH 76'-0"

AutoCAD SHX Text

11

AutoCAD SHX Text

2"%%c

AutoCAD SHX Text

CONDUIT FROM "PDCA" TO "IRS".

AutoCAD SHX Text


AutoCAD SHX Text

12

AutoCAD SHX Text

(3) 3"%%c

AutoCAD SHX Text

CONDUITS FROM "PDCA" TO "B" WITH A MINIMUM 6" BENDING RADIUS.

AutoCAD SHX Text


AutoCAD SHX Text

13

AutoCAD SHX Text

3"%%c

AutoCAD SHX Text

CONDUIT FROM "PDCB" TO "B" WITH A MINIMUM 6" BENDING RADIUS.

AutoCAD SHX Text


AutoCAD SHX Text

14

AutoCAD SHX Text

2-1/2"%%c

AutoCAD SHX Text

CONDUIT FROM "PDCB" TO "B".

AutoCAD SHX Text


AutoCAD SHX Text

15

AutoCAD SHX Text

3"%%c

AutoCAD SHX Text

CONDUIT FROM "B" TO "ICS".

AutoCAD SHX Text


AutoCAD SHX Text

16

AutoCAD SHX Text

1-1/2"%%c

AutoCAD SHX Text

CONDUIT FROM "B" TO "IRS".

AutoCAD SHX Text


AutoCAD SHX Text

17

AutoCAD SHX Text

(2) 3"%%C

AutoCAD SHX Text

CONDUITS, IF REQUIRED PER LOCAL CODE, FROM "S" TO "B1". TO CONTAIN SIEMENS COOLING WATER HOSES WITH A MINIMUM 6" BENDING RADIUS.

AutoCAD SHX Text

MAX. CONDUIT LENGTH 90'-0" SEE SHEET M-101

AutoCAD SHX Text

18

AutoCAD SHX Text

1"%%C

AutoCAD SHX Text

CONDUIT, IF REQUIRED PER LOCAL CODE, FOR CONDENSATION HOSE FROM "B1" TO SELECTED DRAIN TYPE. THE MINIMUM BENDING RADIUS IS 1 3/16".

AutoCAD SHX Text


AutoCAD SHX Text

19

AutoCAD SHX Text

2-1/2"%%C

AutoCAD SHX Text

CONDUIT FROM "IN2" TO "IN3", VERIFY LENGTH RESTRICTIONS WITH MANUFACTURER.

AutoCAD SHX Text

20

AutoCAD SHX Text

2-1/2"%%c

AutoCAD SHX Text

CONDUIT FROM "ICS" TO "F1".

AutoCAD SHX Text


AutoCAD SHX Text

21

AutoCAD SHX Text

2-1/2"%%c

AutoCAD SHX Text

CONDUIT FROM "VD1" (PDCA) TO "F1".

AutoCAD SHX Text


AutoCAD SHX Text

22

AutoCAD SHX Text

AS REQUIRED

AutoCAD SHX Text

CONDUIT FROM "MP" TO "A2" (S), SIZED BY ELECTRICAL ENGINEER OF RECORD.

AutoCAD SHX Text

SEE POWER SCHEDULE

AutoCAD SHX Text

23

AutoCAD SHX Text

1-1/2"%%c

AutoCAD SHX Text

CONDUIT FROM "A2" (S) TO "DC" AND "DC" TO "S1".

AutoCAD SHX Text


AutoCAD SHX Text

24

AutoCAD SHX Text

1-1/2"%%c

AutoCAD SHX Text

CONDUIT FROM "S" TO "B".

AutoCAD SHX Text


AutoCAD SHX Text

25

AutoCAD SHX Text

(2) 3"%%C

AutoCAD SHX Text

CONDUITS, IF REQUIRED PER LOCAL CODE, FROM "S" TO "S2". THE MINIMUM BENDING RADIUS IS 12.5".

AutoCAD SHX Text

MAX. CONDUIT LENGTH 131'-0" SEE SHEET M-101

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

6 8


08013

M-101ATTENTION:

RE

FE

RE

NC

E D

OC

UM

EN

T - N

OT

F

OR

C

ON

ST

RU

CT

IO

N

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

FOR CT GANTRY ONLY

AutoCAD SHX Text

MIN. 8'-6 3/8" MAX. 12'-1 1/16"

AutoCAD SHX Text

MINIMUM 7'-2 5/8"

AutoCAD SHX Text

HEIGHT DIFFERENCE BETWEEN HEAT EXCHANGER AND OUTDOOR UNIT MUST NOT EXCEED ±65-7".

AutoCAD SHX Text

THE OUTDOOR COOLING UNIT IS SUPPLIED BY SIEMENS, LOCATED AND INSTALLED BY THE CUSTOMER/ CONTRACTOR. THE INDOOR HEAT EXCHANGER CABINET IS SUPPLIED BY SIEMENS, INSTALLED BY THE CUSTOMER/CONTRACTOR. IF THE SYSTEM IS TO BE RELOCATED, THE OUTDOOR COOLING UNIT IS TO BE DEINSTALLED, RELOCATED AND REINSTALLED BY THE CUSTOMER/CONTRACTOR, IF NECESSARY. THE INDOOR HEAT EXCHANGER CABINET IS RELOCATED BY SIEMENS, INSTALLED BY THE CUSTOMER/CONTRACTOR.

AutoCAD SHX Text

SIEMENS SUPPLIED AND INSTALLED WATER HOSES FROM THE HEAT EXCHANGER TO THE CT GANTRY. THE HOSES SHALL BE RUN IN (2) 3" CONDUITSOR ACCORDING TO LOCAL CODE. (SEE SHEET E-102, ITEM 17).

AutoCAD SHX Text

SIEMENS SUPPLIED WATER HOSES FROM THE HEAT EXCHANGER TO THE OUTDOOR UNIT TO BE INSTALLED BY THE CUSTOMER/CONTRACTOR. THE HOSES SHALL BE RUN IN (2) 3" CONDUITS ORACCORDING TO CODE. (SEE SHEET E-102, ITEM 25 AND DETAILS THIS SHEET).

AutoCAD SHX Text

SIEMENS SUPPLIED AND INSTALLED CONDENSATION HOSE ROUTED ACCORDING TO LOCAL CODE TO SELECTED ON-SITE DRAIN. (SEE SHEET E-102, ITEM 18).

AutoCAD SHX Text

EQUIPMENT ROOM

AutoCAD SHX Text

CONTROL ROOM

AutoCAD SHX Text

CT SCAN ROOM

AutoCAD SHX Text

ORIENTATION POINT

AutoCAD SHX Text

NOTE: FOR THE HEAT OUTPUT (BTU/HR) OF ALL SIEMENS EQUIPMENT SHOWN ON THIS PLAN, SEE THE "EQUIPMENT LEGEND" ON SHEET A-101.

AutoCAD SHX Text

M-101

AutoCAD SHX Text

1

AutoCAD SHX Text

M-101

AutoCAD SHX Text

5

AutoCAD SHX Text

M-101-A

AutoCAD SHX Text

3

AutoCAD SHX Text


AutoCAD SHX Text

AS NOTED

AutoCAD SHX Text

L. BACH

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

PROJECT #:

AutoCAD SHX Text

SHEET:

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

REF. #:

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

SHEET OF

AutoCAD SHX Text

DATE:

AutoCAD SHX Text

SHEET OF

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

N/A

AutoCAD SHX Text

TYPICAL REV 12

AutoCAD SHX Text

-ISSUE BLOCK-

AutoCAD SHX Text

DESCRIPTION

AutoCAD SHX Text

DATE

AutoCAD SHX Text

SYM

AutoCAD SHX Text

DEFINITION FLASH

AutoCAD SHX Text

REV 12

AutoCAD SHX Text

MECHANICAL PLAN - WATER/AIR SPLIT OPTION

AutoCAD SHX Text

SCALE: 1/4" = 1'-0"

AutoCAD SHX Text

THE MAXIMUM TEMPERATURE GRADIENT IS 6 K/HR.

AutoCAD SHX Text

REFER TO THE CLIMATOGRAM ABOVE FOR THE PERMITTED CLIMATE RANGE.

AutoCAD SHX Text

THE ROOM AIR SHOULD BE PROTECTED AGAINST CONTAMINATION BY HYDROGEN SULPHIDE, EVEN IN SMALL AMOUNTS. IF A DANGER OF SUCH CONTAMINATION EXISTS, CORRECTIVE ACTIONS HAVE TO BE TAKEN. E.G., EXTRACTOR FANS, SIPHON, MODIFICATION OF VENTILATION INTAKE, ETC..

AutoCAD SHX Text

ENVIRONMENTAL REQUIREMENTS

AutoCAD SHX Text

THE ENVIRONMENTAL REQUIREMENTS FOR THE OPERATOR AND THE SYSTEM IS 64 TO 82 °F WITH A RELATIVE HUMIDITY OF20-75% AND A BAROMETRIC PRESSURE OF 11.6 TO 15.4 PSI.

AutoCAD SHX Text

EXTERIOR AIR VENTS SHOULD BE EQUIPPED WITH A FILTRATION SYSTEM OF THE FILTER CLASS MERV 8 TO FILTER DUST PARTICLES >10 um.

AutoCAD SHX Text

TEMPERATURE, HUMIDITY, DUST, AIR CONTAMINATION:

AutoCAD SHX Text

TEMPERATURE (°F)

AutoCAD SHX Text

% RELATIVE HUMIDITY

AutoCAD SHX Text

95

AutoCAD SHX Text

86

AutoCAD SHX Text

82

AutoCAD SHX Text

77

AutoCAD SHX Text

68

AutoCAD SHX Text

64

AutoCAD SHX Text

59

AutoCAD SHX Text

50

AutoCAD SHX Text

41

AutoCAD SHX Text

32

AutoCAD SHX Text

0

AutoCAD SHX Text

10

AutoCAD SHX Text

20

AutoCAD SHX Text

30

AutoCAD SHX Text

40

AutoCAD SHX Text

50

AutoCAD SHX Text

60

AutoCAD SHX Text

70

AutoCAD SHX Text

75

AutoCAD SHX Text

80

AutoCAD SHX Text

90

AutoCAD SHX Text

100

AutoCAD SHX Text

1/2"=1'-0"

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

OUTDOOR COOLING UNIT MOUNTING DETAIL

AutoCAD SHX Text

SIDE VIEW

AutoCAD SHX Text

TOP VIEW

AutoCAD SHX Text

WEATHER PROTECTION

AutoCAD SHX Text

AIR INTAKE

AutoCAD SHX Text

CABLE CONNECTION BOX

AutoCAD SHX Text

MIN. SERVICE CLEARANCE

AutoCAD SHX Text

THE OUTDOOR UNIT MUST BE LOCATED AND INSTALLED BY THE CUSTOMER/CONTRACTOR. THIS UNIT IS PART OF A PRE-INSTALLATION KIT THAT MUST BE INSTALLED PRIOR TO THE DELIVERY OF THE SYSTEM. IT MAY BE LOCATED OUTSIDE ON THE ROOF OR GROUND, OR IN AN AIR CONDITIONED ROOM IF AN OUTSIDE INSTALLATION IS NOT POSSIBLE. THE MOUNTING SURFACE MUST BE LEVEL. IT IS RECOMMENDED THAT THE UNIT BE PROTECTED AGAINST RAIN, SNOW, ETC. THE OUTDOOR UNIT MUST ALWAYS BE BOLTED TO THE FLOOR THROUGH THE DRILL HOLES IN THE FRAME. MATERIALS FOR BOLTING MUST BE SUPPLIED BY THE CUSTOMER/CONTRACTOR. MOUNTING TO A WALL IS ALSO POSSIBLE. MATERIALS FOR MOUNTING AND STRUCTURAL SUPPORT MUST BE DESIGNED, SUPPLIED AND INSTALLED BY THE CUSTOMER/CONTRACTOR.

AutoCAD SHX Text

FRONT VIEW

AutoCAD SHX Text

WALL MOUNTING - NO SCALE

AutoCAD SHX Text

OUTDOOR COOLING UNIT

AutoCAD SHX Text

ON-SITE SUPPORT

AutoCAD SHX Text

WALL

AutoCAD SHX Text

ON-SITE WEATHER PROTECTION (RECOMMENDED)

AutoCAD SHX Text

NOTE: SPACE FOR SERVICE MUST ALSO BE MAINTAINED

AutoCAD SHX Text

WATER INLET & RETURN

AutoCAD SHX Text

MIN. SERVICE CLEARANCE

AutoCAD SHX Text


AutoCAD SHX Text

COOLING FAN (EXHAUST)

AutoCAD SHX Text

MIN. FOR EXHAUST

AutoCAD SHX Text


AutoCAD SHX Text

5

AutoCAD SHX Text

TOP VIEW

AutoCAD SHX Text

FRONT VIEW

AutoCAD SHX Text

CONNECTION DETAILS

AutoCAD SHX Text

WATER INLET FROM OUTDOOR UNIT (PRIMARY CIRCUIT)

AutoCAD SHX Text

WATER INLET TO GANTRY (SECONDARY COOLING CIRCUIT)

AutoCAD SHX Text

WATER RETURN FROM GANTRY (SECONDARY COOLING CIRCUIT)

AutoCAD SHX Text

WATER RETURN TO OUTDOOR UNIT (PRIMARY CIRCUIT)

AutoCAD SHX Text

OPENING IN CABINET BASE FOR ROUTING HOSES AND CABLES

AutoCAD SHX Text

HEAT EXCHANGER

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

3/4"=1'-0"

AutoCAD SHX Text

1

AutoCAD SHX Text

SIEMENS HEAT EXCHANGER - INDOOR UNIT (FRONT)

AutoCAD SHX Text

SIEMENS OUTDOOR UNIT (FRONT)

AutoCAD SHX Text

COOLING DIAGRAM

AutoCAD SHX Text

WATER HOSES SHOWN SCHEMATICALLY

AutoCAD SHX Text

SIEMENS GANTRY (BACK SIDE)

AutoCAD SHX Text

SCALE: NONE

AutoCAD SHX Text

A 3/4" HOSE BIB AND A WATER DRAIN (EX. SINK) MUST BE AVAILABLE IN THE EQUIPMENT ROOM OR IN THE SCAN ROOM NEAR THE HEAT EXCHANGER FOR FILLING THE COOLING CIRCUITS.

AutoCAD SHX Text

THE COOLING CIRCUIT BETWEEN THE OUTDOOR UNIT AND THE INDOOR UNIT IS THE PRIMARY COOLING CIRCUIT. THE COOLING CIRCUIT BETWEEN THE GANTRY AND THE INDOOR COOLING UNIT IS THE SECONDARY COOLING CIRCUIT. THE PRIMARY CIRCUIT IS TO BE FILLED BY THE CUSTOMER/CONTRACTOR. THE STATIC FILL PRESSURE MUST BE SET TO 29 PSI AFTER FILLING FOR THE PRIMARY CIRCUIT AND 22 PSI FOR THE SECONDARY CIRCUIT. THE PUMP IN THE PRIMARY COOLING CIRCUIT GENERATES AN OPERATING PRESSURE OF 29-73 PSI AT THE PUMP OUTLET. THE PUMP IN THE SECONDARY COOLING CIRCUIT GENERATES AN OPERATING PRESSURE OF 58-73 PSI AT THE PUMP OUTLET. THE WATER VOLUME IN THE PRIMARY COOLING CIRCUIT IS APPROX. 23.8 GALLONS. THE WATER VOLUME IN THE SECONDARY COOLING CIRCUIT IS APPROX. 13.2 GALLONS, NOT INCLUDING ANY HOSE EXTENSIONS. ANTIFREEZE (GLYKOSOL N ONLY) WILL BE UTILIZED BY THE TECHNICIAN WHO WILL START THE SYSTEM. THE PERMITTED MIXING RATIO IS 40:60 (GLYCOL:WATER) FOR TEMPERATURE RANGE -22° TO 122°. 26.4 GALLONS OF ANTIFREEZE MIXTURE (GLYKOSOL N) IS INCLUDED IN DELIVERY. WATER CANNOT BE ADDED TO THIS MIXTURE.

AutoCAD SHX Text

THE WATER-AIR SPLIT COOLING SYSTEM IS DELIVERED AS A PRE-INSTALLATION KIT. IT MUST BE INSTALLED PRIOR TO DELIVERY OF THE SYSTEM BY THE CUSTOMER/CONTRACTOR. THE FOLLOWING IS INCLUDED IN THE PRE-INSTALLATION KIT: OUTDOOR COOLING UNIT, INDOOR HEAT EXCHANGER CABINET, HOSES AND SYSTEM CABLES, 26.4 GALLONS ANTIFREEZE MIXTURE (GLYKOSOL N), CONNECTION KIT AND CONNECTION SCHEMATIC.

AutoCAD SHX Text

2

AutoCAD SHX Text

PRIMARY CIRCUIT

AutoCAD SHX Text

WATER TEMPERATURE RANGE:

AutoCAD SHX Text

AIR INTAKE TEMPERATURE RANGE:

AutoCAD SHX Text

RELATIVE HUMIDITY:

AutoCAD SHX Text

-13° TO 136°

AutoCAD SHX Text

-22° TO 122°

AutoCAD SHX Text

0-100%

AutoCAD SHX Text


AutoCAD SHX Text

SIEMENS OUTDOOR UNIT (FRONT)

AutoCAD SHX Text

CHILLED WATER HOSES (PRIMARY LOOP)

AutoCAD SHX Text

THE CHILLED WATER HOSES ARE SUPPLIED IN THE FOLLOWING LENGTH ONLY: 131 FEET. A 1 1/4" SUPPLY AND RETURNCOPPER PIPE CAN BE USED INSTEAD OF THE SIEMENS WATER HOSES, HOWEVER THE SUPPLIED WATER HOSES MUST BE CUT AND USED TO CONNECT THE SIEMENS COMPONENTS TO THE COPPER PIPE. THE LENGTH MAY BE EXTENDED FROM 131 FEET UP TO 196 FEET WITH CUSTOMER/CONTRACTOR SUPPLIED 1 1/4" INNER COPPER PIPE USED WITH SIEMENS WATERHOSES OR FROM 131 FEET UP TO 328 FEET WITH CUSTOMER/CONTRACTOR SUPPLIED 1 1/2" INNER COPPERPIPE USED WITH SIEMENS WATER HOSES. 20 ELBOW ADAPTERS (90 DEGREES) ARE PERMITTED WITHIN THE TOTAL RUN. CUSTOMER/CONTRACTOR TO SUPPLY AND INSTALL FITTINGS TO MATCH THE SELECTED PIPE SIZE. CUSTOMER/CONTRACTOR TO INSULATE WITH 1/2" ARMAFLEX INSULATION, INCLUDING FLEX HOSES.

AutoCAD SHX Text

(1 1/4" FEMALE NPT SUPPLIED AND INSTALLED BY CUSTOMER/ CONTRACTOR) ONLY IF COPPER PIPE IS USED WITH WATER HOSES. TO BE CONNECTED TO SIEMENS SUPPLIED FITTING KIT (ORDERED SEPARATELY) AND INSTALLED BY THE CUSTOMER/CONTRACTOR.

AutoCAD SHX Text

SIEMENS WATER HOSES OR 1 1/4" INNER COPPER PIPES (SUPPLIEDAND INSTALLED BY CUSTOMER/ CONTRACTOR.

AutoCAD SHX Text

SIEMENS FLEXIBLE WATER HOSES

AutoCAD SHX Text


AutoCAD SHX Text

BTU/HR TO AIR (EXHAUST):

AutoCAD SHX Text

119,425

AutoCAD SHX Text

PRIMARY CIRCUIT

AutoCAD SHX Text

NONE

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text


AutoCAD SHX Text

IF THE SIEMENS WATER HOSES ARE EXTENDED (>131 FEET), THE LINE VOLTAGE/CONTROL CABLE THAT RUNS FROM THE HEAT EXCHANGER CABINET TO THE OUTDOOR UNIT MUST ALSO BE EXTENDED. THESE EXTENDED CABLES ARE AVAILABLE THROUGH SIEMENS.

AutoCAD SHX Text

ADDITIONAL ANTIFREEZE (GLYKOSOL N ONLY) MUST ALSO BE SUPPLIED BY THE CUSTOMER/CONTRACTOR FOR HOSE EXTENSION. GLYKOSOL N CAN BE ORDERED THROUGH SIEMENS LOCAL CSE. USE OF AUTOMOTIVE ANTIFREEZE IS PROHIBITED.

AutoCAD SHX Text

3

AutoCAD SHX Text

50°F (SECONDARY COOLINGCIRCUIT)

AutoCAD SHX Text

-13°F TO 136°F MAXIMUM(PRIMARY COOLING CIRCUIT)

AutoCAD SHX Text

ANTIFREEZE (GLYKOSOL N ONLY) MAY BE ADDED TO THE PRIMARY COOLING CIRCUIT ONLY, BY THE TECHNICIAN WHO WILL START THE SYSTEM. THE PERMITTED MIXING RATIO IS 40:60 (GLYCOL:WATER) FOR TEMPERATURE RANGE -22° TO 122°F. 26.4 GALLONS OF ANTIFREEZE MIXTURE (GLYKOSOL N) IS INCLUDED IN DELIVERY. WATER CANNOT BE ADDED TO THIS MIXTURE. USE OF AUTOMOTIVE ANTIFREEZE IS PROHIBITED.

AutoCAD SHX Text

THE WATER MUST BE OF DRINKABLE QUALITY. IF THE WATER IS OF LESSER QUALITY A FILTER WITH A MESH OF 200 MICRONS IS REQUIRED IN THE PRIMARY INLET SUPPLIED BY THE CUSTOMER/ CONTRACTOR.

AutoCAD SHX Text

TECHNICAL DATA

AutoCAD SHX Text

TEMPERATURE RANGE OF WATER

AutoCAD SHX Text

AMBIENT AIR TEMPERATURE RANGE (AIR INTAKE)

AutoCAD SHX Text

FILTRATION

AutoCAD SHX Text

BTU/HR TO AIR (EXHAUST)

AutoCAD SHX Text

119,425

AutoCAD SHX Text

200 MICRONS

AutoCAD SHX Text

-22°F TO 122°F MAXIMUM

AutoCAD SHX Text

WATER QUALITY

AutoCAD SHX Text

ANTIFREEZE

AutoCAD SHX Text

SECONDARY CIRCUIT

AutoCAD SHX Text

DUE TO THE HIGH NOISE (<60 dB), IT IS RECOMMENDED TO INSTALL THE HEAT EXCHANGER IN A SEPARATE ROOM. THE HEAT EXCHANGER MAY BE INSTALLED TO THE LEFT OR RIGHT OF PDCA/PDCB OR INDEPENDENT OF THE PDC CABINETS.

AutoCAD SHX Text

WATER TEMPERATURE:

AutoCAD SHX Text

57°F

AutoCAD SHX Text

SIEMENS WATER HOSES OR 1" INNER COPPER PIPES(SUPPLIED AND INSTALLED BY CUSTOMER/CONTRACTOR

AutoCAD SHX Text


AutoCAD SHX Text

HEAT EXCHANGER

AutoCAD SHX Text

CHILLED WATER HOSES (SECONDARY COOLING CIRCUIT)

AutoCAD SHX Text

NOMINAL FLOW RATE:

AutoCAD SHX Text

660 GALLONS/HR (WITH 98 FT. HOSE)

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

SECONDARY CIRCUIT

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

PRESSURE CONNECTORS SUPPLIED BY CUSTOMER/ CONTRACTOR (ONLY IF COPPER PIPE IS USED WITH WATER HOSES)

AutoCAD SHX Text

THE CHILLED WATER HOSES HAVE TO BE ORDERED SEPARATELY AND WILL BE SUPPLIED IN THE FOLLOWING THREE LENGTHS ONLY: 31 FEET, 64 FEET AND 96 FEET. A 1" SUPPLY ANDRETURN COPPER PIPE CAN BE USED INSTEAD OF THE SIEMENS WATER HOSES, HOWEVER THE SUPPLIED WATER HOSES MUST BE CUT AND USED TO CONNECT THE SIEMENS COMPONENTS TO THE COPPER PIPE. THE LENGTH MAY BE EXTENDED FROM 96 FEET UP TO 164 FEET WITH CUSTOMER/CONTRACTOR SUPPLIED 1" INNER COPPER PIPE USED WITH SIEMENS WATER HOSESOR FROM 96 FEET UP TO 229 FEET WITH CUSTOMER/ CONTRACTOR SUPPLIED 1 1/4" INNER COPPER PIPE USEDWITH SIEMENS WATER HOSES. 20 ELBOW ADAPTERS (90 DEGREES) ARE PERMITTED WITHIN THE TOTAL RUN. CUSTOMER/CONTRACTOR TO SUPPLY AND INSTALL FITTINGS TO MATCH THE SELECTED PIPE SIZE. CUSTOMER/CONTRACTOR TO INSULATE WITH 1/2" ARMAFLEX INSULATION, INCLUDING FLEX HOSES. THE OUTER DIAMETER OF THE WATER HOSES IS 1-3/8". INSULATED WATER HOSES ARE AVAILABLE THROUGH SIEMENS.

AutoCAD SHX Text

IF THE SIEMENS WATER HOSES ARE EXTENDED (>96 FEET), THE DATA CABLE THAT RUNS FROM THE HEAT EXCHANGER CABINET TO THE GANTRY MUST ALSO BE EXTENDED. THESE EXTENDED CABLES ARE AVAILABLE THROUGH SIEMENS.

AutoCAD SHX Text

SCALE: NONE

AutoCAD SHX Text

4

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

7 8


08013

M-101-AATTENTION:

RE

FE

RE

NC

E D

OC

UM

EN

T - N

OT

F

OR

C

ON

ST

RU

CT

IO

N

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

FOR CT GANTRY ONLY

AutoCAD SHX Text

MIN. 8'-6 3/8" MAX. 12'-1 1/16"

AutoCAD SHX Text

MINIMUM 7'-2 5/8"

AutoCAD SHX Text

EQUIPMENT ROOM

AutoCAD SHX Text

CONTROL ROOM

AutoCAD SHX Text

CT SCAN ROOM

AutoCAD SHX Text

ORIENTATION POINT

AutoCAD SHX Text

NOTE: FOR THE HEAT OUTPUT (BTU/HR) OF ALL SIEMENS EQUIPMENT SHOWN ON THIS PLAN, SEE THE "EQUIPMENT LEGEND" ON SHEET A-101.

AutoCAD SHX Text

SIEMENS SUPPLIED AND INSTALLED CONDENSATION HOSE ROUTED ACCORDING TO LOCAL CODE TO SELECTED ON-SITE DRAIN.

AutoCAD SHX Text

SIEMENS SUPPLIED AND INSTALLED WATER HOSES ROUTED IN (2) 3" CONDUITS TOON-SITE CHILLED WATER CONNECTION.

AutoCAD SHX Text

M-101-A

AutoCAD SHX Text

1

AutoCAD SHX Text

M-101-A

AutoCAD SHX Text

2

AutoCAD SHX Text

M-101-A

AutoCAD SHX Text

3

AutoCAD SHX Text

M-101-A

AutoCAD SHX Text

1

AutoCAD SHX Text


AutoCAD SHX Text

AS NOTED

AutoCAD SHX Text

L. BACH

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

PROJECT #:

AutoCAD SHX Text

SHEET:

AutoCAD SHX Text

SCALE:

AutoCAD SHX Text

REF. #:

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

SHEET OF

AutoCAD SHX Text

DATE:

AutoCAD SHX Text

SHEET OF

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

DRAWN BY:

AutoCAD SHX Text

N/A

AutoCAD SHX Text

TYPICAL REV 12

AutoCAD SHX Text

-ISSUE BLOCK-

AutoCAD SHX Text

DESCRIPTION

AutoCAD SHX Text

DATE

AutoCAD SHX Text

SYM

AutoCAD SHX Text

DEFINITION FLASH

AutoCAD SHX Text

REV 12

AutoCAD SHX Text

MECHANICAL PLAN - HOSPITAL SUPPLIED CHILLED WATER OPTION

AutoCAD SHX Text

SCALE: 1/4" = 1'-0"

AutoCAD SHX Text

THE MAXIMUM TEMPERATURE GRADIENT IS 6 K/HR.

AutoCAD SHX Text

REFER TO THE CLIMATOGRAM ABOVE FOR THE PERMITTED CLIMATE RANGE.

AutoCAD SHX Text

THE ROOM AIR SHOULD BE PROTECTED AGAINST CONTAMINATION BY HYDROGEN SULPHIDE, EVEN IN SMALL AMOUNTS. IF A DANGER OF SUCH CONTAMINATION EXISTS, CORRECTIVE ACTIONS HAVE TO BE TAKEN. E.G., EXTRACTOR FANS, SIPHON, MODIFICATION OF VENTILATION INTAKE, ETC..

AutoCAD SHX Text

ENVIRONMENTAL REQUIREMENTS

AutoCAD SHX Text

THE ENVIRONMENTAL REQUIREMENTS FOR THE OPERATOR AND THE SYSTEM IS 64 TO 82 °F WITH A RELATIVE HUMIDITY OF20-75% AND A BAROMETRIC PRESSURE OF 11.6 TO 15.4 PSI.

AutoCAD SHX Text

EXTERIOR AIR VENTS SHOULD BE EQUIPPED WITH A FILTRATION SYSTEM OF THE FILTER CLASS MERV 8 TO FILTER DUST PARTICLES >10 um.

AutoCAD SHX Text

TEMPERATURE, HUMIDITY, DUST, AIR CONTAMINATION:

AutoCAD SHX Text

TEMPERATURE (°F)

AutoCAD SHX Text

% RELATIVE HUMIDITY

AutoCAD SHX Text

95

AutoCAD SHX Text

86

AutoCAD SHX Text

82

AutoCAD SHX Text

77

AutoCAD SHX Text

68

AutoCAD SHX Text

64

AutoCAD SHX Text

59

AutoCAD SHX Text

50

AutoCAD SHX Text

41

AutoCAD SHX Text

32

AutoCAD SHX Text

0

AutoCAD SHX Text

10

AutoCAD SHX Text

20

AutoCAD SHX Text

30

AutoCAD SHX Text

40

AutoCAD SHX Text

50

AutoCAD SHX Text

60

AutoCAD SHX Text

70

AutoCAD SHX Text

75

AutoCAD SHX Text

80

AutoCAD SHX Text

90

AutoCAD SHX Text

100

AutoCAD SHX Text

CONDENSATION WATER DRAIN

AutoCAD SHX Text

GANTRY (BACK SIDE)

AutoCAD SHX Text

WALL

AutoCAD SHX Text

SINK

AutoCAD SHX Text

SIEMENS CONDENSATION WATER HOSE (LENGTH: 32'-9", OUTSIDE DIA. 3/8"). MAX. BENDING RADIUS 1 3/16".

AutoCAD SHX Text

WATER DRAIN

AutoCAD SHX Text

HOSE OUTLET

AutoCAD SHX Text

FLOOR DRAIN

AutoCAD SHX Text

MIN. 4" FLOOR DRAIN AS REQUIRED PER LOCAL CODE. PROVIDE SURFACE MOUNTED PULL BOX OR SURFACE DUCT AS REQUIRED.

AutoCAD SHX Text

A WATER DRAIN IS REQUIRED TO BE SUPPLIED AND INSTALLED BY THE CUSTOMER/CONTRACTOR TO DRAIN CONDENSED WATER FROM THE GANTRY. THE DRAIN MUST BE WITHIN 32'-9" OF THE GANTRY (TO USE THE DELIVERED WATER HOSE) AND CANNOT EXCEED 9'-10" ABOVE THE FINISHED FLOOR. THE DISTANCE FROM THE GANTRY TO THE DRAIN MAY BE EXTENDED UP TO 98'-5" WITH EXTENSION MATERIAL PROVIDED BY THE CUSTOMER/CONTRACTOR. BELOW ARE SOME EXAMPLES OF POSSIBLE WATER DRAINS. THE MECHANICAL CONTRACTOR IS RESPONSIBLE FOR DETERMINING WHICH DRAIN TYPE TO USE AND FOR SPECIFYING, SUPPLYING AND INSTALLING THE PLUMBING FIXTURES NECESSARY TO CONNECT THE SIEMENS WATER HOSE TO THE SELECTED DRAIN.

AutoCAD SHX Text

SINK DRAIN

AutoCAD SHX Text

GANTRY (TOP VIEW)

AutoCAD SHX Text

THE MAX. FLOW RATE OF THE CONDENSED WATER IS .53 GALLONS/HR AT 75% RELATIVE HUMIDITY.

AutoCAD SHX Text

3

AutoCAD SHX Text

WATER FLOW RATE

AutoCAD SHX Text

THIS DIAGRAM ILLUSTRATES THE DEPENDENCY OF THE MINIMUM CIRCULATING VOLUME ON CHILLED WATER TEMPERATURE.

AutoCAD SHX Text

TEMPERATURE OF CHILLED WATER AT INLET

AutoCAD SHX Text

15.4

AutoCAD SHX Text

13.2

AutoCAD SHX Text

11.0

AutoCAD SHX Text

8.8

AutoCAD SHX Text

6.6

AutoCAD SHX Text

4.4

AutoCAD SHX Text

2.2

AutoCAD SHX Text

0.0

AutoCAD SHX Text

39.2

AutoCAD SHX Text

42.8

AutoCAD SHX Text

46.4

AutoCAD SHX Text

50

AutoCAD SHX Text

53.6

AutoCAD SHX Text

2.9

AutoCAD SHX Text

3.3

AutoCAD SHX Text

3.6

AutoCAD SHX Text

5.7

AutoCAD SHX Text

°F

AutoCAD SHX Text

GPM

AutoCAD SHX Text

CIRCULATING VOLUME

AutoCAD SHX Text

WITH 40% ANTIFREEZE AGENT

AutoCAD SHX Text

WITHOUT ANTIFREEZE AGENT

AutoCAD SHX Text

4.3

AutoCAD SHX Text

4.9

AutoCAD SHX Text

7.0

AutoCAD SHX Text

5.7

AutoCAD SHX Text

4.5

AutoCAD SHX Text

57.2

AutoCAD SHX Text

60.8

AutoCAD SHX Text

7.9

AutoCAD SHX Text

14.0

AutoCAD SHX Text

9.0

AutoCAD SHX Text

13.0

AutoCAD SHX Text

GANTRY HOSE CONNECTION

AutoCAD SHX Text

WATER RETURN

AutoCAD SHX Text

WATER SUPPLY

AutoCAD SHX Text

WATER RETURN

AutoCAD SHX Text

WATER SUPPLY

AutoCAD SHX Text

GANTRY TOP VIEW

AutoCAD SHX Text

GANTRY (BACK SIDE)

AutoCAD SHX Text

DETAIL "A"

AutoCAD SHX Text

DETAIL "A"

AutoCAD SHX Text

WATER RETURN

AutoCAD SHX Text

WATER SUPPLY

AutoCAD SHX Text

SCALE: NONE

AutoCAD SHX Text

1

AutoCAD SHX Text

CHILLED WATER

AutoCAD SHX Text

THE COOLING SYSTEM IS INTEGRATED WITHIN THE GANTRY. THE ON-SITE CHILLED WATER SUPPLY AND RETURN ARE CONNECTED DIRECTLY TO THE GANTRY.

AutoCAD SHX Text

THE SIEMENS FLEXIBLE CHILLED WATER HOSES HAVE TO BE ORDERED SEPARATELY AND WILL BE SUPPLIED IN THE FOLLOWING THREE LENGTHS ONLY: 31 FEET, 64 FEET AND 96 FEET. THE MIN. ACCEPTABLE BENDING RADIUS OF THE HOSES IS 6". THE OUTER DIAMETER OF THE WATER HOSES IS 1-3/8". CUSTOMER/CONTRACTOR TO INSULATE NON-INSULATED WATER HOSES WITH 1/2" ARMAFLEX INSULATION. INSULATED WATER HOSES ARE AVAILABLE THROUGH SIEMENS. THESE INSULATED HOSES ARE USABLE FOR ON-SITE WATER TEMPERATURE RANGES GREATER THAN OR EQUAL TO 46.4 °F TO 60.8 °F. ADDITIONALINSULATION MUST BE SUPPLIED AND APPLIED TO THE HOSES BY THE CUSTOMER/CONTRACTOR FOR ON-SITE WATER TEMPERATURE RANGES 39.2° F TO <46.4° F. THIS MAY REQUIRE AN INCREASEIN THE CONDUIT/DUCT SIZE FOR HOSES.

AutoCAD SHX Text

ON-SITE CHILLED WATER REQUIREMENTS

AutoCAD SHX Text

WATER TEMPERATURE: MINIMUM 39.2°F TO 60.8°F MAXIMUMNOMINAL OPERATING PRESSURE: 29 TO 87 PSI (145 PSI MAXIMUM) FLOW RATE: DEPENDS ON WATER TEMPERATURE DIFFERENTIAL PRESSURE: AS RELATES TO WATER CIRCULATION

AutoCAD SHX Text


AutoCAD SHX Text

ON-SITE CHILLED WATER CONNECTION TO HOSPITAL COOLING CIRCUIT.

AutoCAD SHX Text

SIEMENS FLEXIBLE WATER HOSES.

AutoCAD SHX Text

WALL

AutoCAD SHX Text

CHILLED WATER HOSES

AutoCAD SHX Text

A 3/4" HOSE BIB AND A WATER DRAIN (EX. SINK) MUST BE AVAILABLE NEAR THE GANTRY FOR FILLING THE COOLING SYSTEM.

AutoCAD SHX Text

2

AutoCAD SHX Text

SCALE: NONE

AutoCAD SHX Text

2

AutoCAD SHX Text

AN ANTIFREEZE AGENT MAY BE ADDED, BY THE TECHNICIAN WHO WILL START THE SYSTEM, TO THE ON-SITE CIRCUIT TO PROVIDE PROTECTION FOR TEMPERATURES TO -13°F WITH A MIXTURE OF40% ANTIFREEZE. TO COMPENSATE FOR THE RESULTING REDUCTION IN COOLING CAPACITY, THE WATER FLOW RATE WILL HAVE TO BE INCREASED. WATER WITH ANTIFREEZE FROM THE ON-SITE CHILLED WATER MUST BE BETWEEN 39.2° F AND 57.2° F. ONLY WATER AT THIS TEMPERATURE MAY FLOW THROUGH THE WATER/WATER COOLING SYSTEM. ANTIFREEZE TO BE SUPPLIED BY THE CUSTOMER/CONTRACTOR. CHILLER MANUFACTURER'S SPECIFICATIONS MAY DIFFER, VERIFY WITH SIEMENS PROJECT MANAGER.

AutoCAD SHX Text

TECHNICAL DATA

AutoCAD SHX Text

MINIMUM 39.2°F TO60.8°F MAXIMUM

AutoCAD SHX Text

WATER SUPPLY RATE

AutoCAD SHX Text

SEE WATER FLOW RATE DIAGRAM

AutoCAD SHX Text

TEMPERATURE RANGE OF WATER

AutoCAD SHX Text

BTU DISCHARGE TO THE WATER

AutoCAD SHX Text

58,045 BTU/HR

AutoCAD SHX Text

29 TO 87 PSI

AutoCAD SHX Text

NOMINAL OPERATING PRESSURE

AutoCAD SHX Text

FILTRATION

AutoCAD SHX Text

200 MICRONS

AutoCAD SHX Text

DIFFERENTIAL PRESSURE

AutoCAD SHX Text

SEE DIFFERENTIAL PRESSURE DIAGRAM

AutoCAD SHX Text

MAXIMUM 1 K/MINUTE

AutoCAD SHX Text

TEMPERATURE GRADIENT OF WATER

AutoCAD SHX Text

THE WATER MUST BE OF DRINKABLE QUALITY. IF THE WATER IS OF LESSER QUALITY A FILTER WITH A MESH OF 200 MICRONS IS REQUIRED IN THE ON-SITE INLET.

AutoCAD SHX Text

ANTIFREEZE

AutoCAD SHX Text

WATER QUALITY

AutoCAD SHX Text

(145 PSI MAXIMUM) (1)

AutoCAD SHX Text

1) TO GUARANTEE THE LIMIT OF THE MAXIMUM WATER PRESSURE OF 145 PSI, THE ON-SITE COOLING WATER SYSTEM MUST PROVIDE A SUITABLE SAFETY DEVICE, EX. PRESSURE RELIEF VALVE.

AutoCAD SHX Text

CHILLED WATER COOLING CIRCUIT

AutoCAD SHX Text

PIPING AND HOSE SCHEMATIC CLOSED LOOP CHILLED WATER

AutoCAD SHX Text

VISUAL FLOW GAUGE F-451002LHN (2-20 GPM)

AutoCAD SHX Text

BALL VALVE (BRONZE) B6080

AutoCAD SHX Text

PRESSURE GAUGE 530-2005 (LIQUID FILLED 0-160 PSI)

AutoCAD SHX Text

FILTER W/200 MICRON BAG OR EQUAL THAT MEETS SPECIFICATION.

AutoCAD SHX Text

THERMOMETER (20°-120°F) TG-1, 530-30005

AutoCAD SHX Text

HOSPITAL SUPPLIED CHILLED WATER

AutoCAD SHX Text

FLOOR LINE

AutoCAD SHX Text

RETURN

AutoCAD SHX Text

SUPPLY

AutoCAD SHX Text

3/8" VALVE

AutoCAD SHX Text

PIPING AND FIXTURES TO BE SPECIFIED BY THE MECHANICAL ENGINEER OF RECORD AND TO BE SUPPLIED AND INSTALLED BY THE MECHANICAL CONTRACTOR. RECOMMENDED PIPE SIZE FOR TOTAL LENGTH OF PIPING LOOP IS USUALLY 1". THE MECHANICAL ENGINEER MUST DETERMINE THE ACTUAL PIPE SIZE REQUIRED FOR THE TOTAL LENGTH OF THE RUN. THE ON-SITE PIPES ARE TO BE INSULATED WITH 1/2" ARMAFLEX INSULATION BY THE CUSTOMER/CONTRACTOR. SIEMENS NON-INSULATED FLEXIBLE WATER HOSES ARE TO BE INSULATED WITH 1/2" ARMAFLEX INSULATION BY THE CUSTOMER/CONTRACTOR. INSULATED WATER HOSES ARE AVAILABLE THROUGH SIEMENS. THESE INSULATED HOSES ARE USABLE FOR ON-SITE WATER TEMPERATURE RANGES GREATER THAN OR EQUAL TO 46.4 °F TO 60.8 °F.ADDITIONAL INSULATION MUST BE SUPPLIED AND APPLIED TO THE HOSES BY THE CUSTOMER/CONTRACTOR FOR ON-SITE WATER TEMPERATURE RANGES 39.2° F TO <46.4° F. THIS MAY REQUIRE AN INCREASE IN THE CONDUIT/DUCT SIZE FOR HOSES.THE CHILLED WATER DELIVERY SYSTEM MUST BE INSTALLED AND CHARGED PRIOR TO EQUIPMENT DELIVERY.

AutoCAD SHX Text

FLEXIBLE WATER HOSES SUPPLIED BY SIEMENS. MAX. LENGTH 96 FEET.

AutoCAD SHX Text


AutoCAD SHX Text

REQUIRED FIXTURE LEGEND

AutoCAD SHX Text

RECOMMENDED ADDITIONAL FIXTURE LEGEND

AutoCAD SHX Text

ALL COMPONENTS SUPPLIED BY MECHANICAL CONTRACTOR AT A CONVENIENT HEIGHT FOR SERVICING. ALL ITEMS IN THE FIXTURE LEGENDS CAN BE ORDERED FROM PROCAM CONTROLS, (800) 333-2556 OR FAX (214) 422-6262

AutoCAD SHX Text

1" MALE NPT

AutoCAD SHX Text

IF HARD PIPE IS USED, IT MUST BE LOCATED A MINIMUM OF 10" FROM THE GANTRY TO ALLOW ROOM TO ATTACH TO SIEMENS HOSES.

AutoCAD SHX Text

PRESSURE LOSS

AutoCAD SHX Text

PSI

AutoCAD SHX Text

CIRCULATING VOLUME

AutoCAD SHX Text

GPM

AutoCAD SHX Text

THIS DIAGRAM ILLUSTRATES THE RELATIONSHIP BETWEEN THE CIRCULATING VOLUME AND THE PRESSURE LOSS IN THE COOLING UNIT WITHIN THE GANTRY.

AutoCAD SHX Text

PRESSURE LOSS

AutoCAD SHX Text

20.3

AutoCAD SHX Text

17.4

AutoCAD SHX Text

14.5

AutoCAD SHX Text

11.6

AutoCAD SHX Text

0

AutoCAD SHX Text

14.0

AutoCAD SHX Text

13.0

AutoCAD SHX Text

4.9

AutoCAD SHX Text

4.3

AutoCAD SHX Text

3.6

AutoCAD SHX Text

2.9

AutoCAD SHX Text

3.3

AutoCAD SHX Text

8.7

AutoCAD SHX Text

5.8

AutoCAD SHX Text

2.9

AutoCAD SHX Text

2.9

AutoCAD SHX Text

2.9

AutoCAD SHX Text

3.3

AutoCAD SHX Text

4.8

AutoCAD SHX Text

8.0

AutoCAD SHX Text

14.5

AutoCAD SHX Text

9.0

AutoCAD SHX Text

7.9

AutoCAD SHX Text

7.0

AutoCAD SHX Text

5.7

AutoCAD SHX Text

4.5

AutoCAD SHX Text

3.0

AutoCAD SHX Text

WITHOUT ANTI- FREEZE AGENT

AutoCAD SHX Text

WITH 40% ANTI- FREEZE AGENT

AutoCAD SHX Text

3.2

AutoCAD SHX Text

3.6

AutoCAD SHX Text

6.8

AutoCAD SHX Text

9.7

AutoCAD SHX Text

18.8

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

8 8

ATTENTION - Siemens Healthineers Flash/PDF...attention: reference document - not for construction....

Documents

Transcript of ATTENTION - Siemens Healthineers Flash/PDF...attention: reference document - not for construction....