Attachments ONLY for RS1000 with PP35. BUYER’S GUIDE
Transcript of Attachments ONLY for RS1000 with PP35. BUYER’S GUIDE
BUYER’S GUIDEl Features l Specifications l Attachments
RS1000
As Shipped
Engine
Starting
Final Drive
Track Clutches
Brakes
Rated Pull
Size
Weight
Speed
Attachments
ASSEMBLED, painted
Honda, 18.5 ft/lbs Tq. [390cc]
Electric Start, at seat
Triple Ball Bearing [sealed]
Dual each Track [forward]
Double, 8” Caliper
1,500 lbs. at Track
51” long, 41” wide, 38” high
700 lbs.
3.15 MPH
Manual or Hydraulic Attachments
D-I-Y KIT, unpainted
Briggs & Stratton, 11.5 ft/lbs Tq. [250cc]
Recoil, at seat
Double Ball Bearing [sealed]
Single each Track [forward]
Single, 8” Caliper
1,000 lbs. at Track
51” long, 41” wide, 38” high
575 lbs.
3.15 MPH
Manual Attachments only
What’s the DIFFERENCEbetween the
RS1000 & MD196K?
RS1000
MAGNATRAC® RS1000
Factory Assembled... Build it Yourself... D-I-Y Kit
BACKHOE BUCKETS - 12” or
16” wide Backhoe Bucket
mounts directly to Backhoe dip-
per arm. (See below on back-
hoe).
Heavy-Duty single
tooth ripper mounts
in place of Bucket...
equipped with two
(2) replaceable
teeth:
(1) 16” x 2” x 1/2”
thick “plow steel”
tooth for stone &
frost picking &
hardpan penetra-
tion to 18” [shown
below right].
(2) 15” x 2” x 1/2”
thick “serrated”
edge tooth... allows
root cutting to
depths of 18”
[not shown].
POWER PACK KIT -
Hydraulic power system
for raising and lowering
select front and rear at-
tachments. Does not in-
clude cylinders, hoses
or fittings. (See HFH15
Hydro Front Hitch &
HRH35 Hydro Rear
Hitch.)
ROLL-OvER PROTECTIvE STRUCTURE - A Magnatrac’s
low center of gravity and ground gripping traction are no
substitute for ROPS protection on uneven ground. Includes
seat belt and mounting hardware. (Requires AM39 Angle
Mounts).
Roll-overProtectiveStructure
MD196K
MINI-DOZER® MD196K
The RS1000 & MD196K are identical in
physical size and share a majority of com-
ponents... The difference is a more power-
ful engine in the RS1000 plus additional
Heavy-Duty drive train components.
MANUAL FRONT HITCH KIT - Standard-
duty front mounted hitch for manual “lift”.
Complete with dual sets of “lift assist”
springs, lift handle and all hardware.
How easy can I lift the MFH15 Manual Front Hitch with “lift assist” springs?
(1) 3 lbs. of force on lift handle will raise the 95 lb. DB44 Dozer Blade.
(2) 29 lbs of force on handle will raise 95 lb. DB44 Blade, 50 lb. BM13 Bucket
Mouth and a 186 lb. “load”... that’s a combined “lift” of over 330 lbs!
BUCKET MOUTH KIT
DOZER BLADE KIT - 42” wide
x 15” high x 3/16” thick solid
steel blade with replaceable
cutting edge. Manually angles
left and right. [Requires MFH15
or HFH15 Front Hitch]
Manual Front Hitch
Bucket Mouth[shown mounted to Dozer Blade]
Dozer Blade
FRONT WEIGHT KIT - Front
mounted weight kit for use as
a counter balance when a
Backhoe is mounted. Heavy-
duty steel bar welded to
plates and mounted to the
front of RS1000. (Additional
slip on weights available for
even more weight).
PP35
FW15
MD196K-MFH15MFH15
MD196K-DB44DB44
MD196K-BM13BM13
HRH35
ROPS20
Hydro RearHitch
BACKHOE KITS - Backhoe mounts directly to a set of AM39 Angle
Mounts Brackets. D1060 utilizes (2) crank down stabilizers and (4) single
stick backhoe controls for each motion. D1060UG utilizes (2) hydraulic
stabilizers and only (2) joystick backhoe controls for all digging opera-
tions. Comes with fully rotatable and adjustable seat. (Fully assembled
on a secondary pallet)
FW15, HFH15,
HE47 and DB44.
SAFETY NOTE: To “safely” counter-balance the Backhoe’s weight,
at a minimum, the following front attachments should be installed:
BACKHOE FROST / CHISEL RIPPER
Power Pack
Front Weight
*
*
*
Attachments... for MD196K & RS1000*
Attaches in minutes to DB44 Dozer Blade with only
two pins... requires no tools! When installed, it forms
a “mouth” that when used with the Blade becomes a
hard-working Bucket. Easily handles a couple of
100 pounds of rocks, concrete, mud,
driveway gravel, etc. Dumps with
simple hand lever. [Not designed
for use with HFH15 Hydro Front Hitch]
Unassembled,Unassembled,Unpainted KIT Unpainted KIT
BACKHOE
BackhoeBucket(B612)
JoystickWobble Controls
BackhoeFrost /ChiselRipper
14
HYDRO REAR HITCH
KIT - All-hydraulic Rear
Hitch allows operator to ef-
fortlessly hook-up and
move logs, rear-mounted
carriers, log splitters, com-
pact trailers, etc. Includes:
cylinder, hoses, fittings &
mounting hardware. Re-
quires PP35 Power Pack.
[below]
BUCKET FORCE...
DIPPER FORCE...
LIFT (@ bucket pivot)...
LIFT (@ dipper pivot)...
SWING ARC...
STABILIZER SPREAD...
TRANSPORT WIDTH...
BUCKET CAPACITIES...
B612...
B816...
2500 lbs1250 lbs135 lbs210 lbs120 deg41.5”41.5”
1.16 cu. ft.1.54 cu. ft.
A - 80”
B - 114”
C - 103”
D - 75”
E - 162”
RATINGS DIMENSIONS
ROCK/DEBRISTHUMB KIT
Rock “thumb” mounts
to D1060/UG Backhoe
“dipper arm” of Backhoe
with two bolts. Distance
of Bucket “teeth” to
Thumb is adjustable.
RockThumb
C
A
B
D
E
2 Feet
2 Ground Level
D1060/UGBACKHOERatings &
Dimensions
MD196K
MINI-D
OZER®
MINI-DOZER®
BR50
RT24
B612 - 12” BucketB616 - 16” Bucket
D1060(Shown)
D1060 - Crank Down Stabilzers with 4 Stick Controls (Pictured)D1060UG - Hydro Stabilzers with Joystick Wobble Controls
ANGLE MOUNTS
- (2) heavy-duty
mounting brackets
are the connection
point for a ROPS,
Backhoe or Ballast
Box.
AngleMounts
AM39
Attachments... ONLY for RS1000 with PP35. [Continued]
MD196K
Buy-Guide 1.01.19
Buy-Guide MD196K & RS1000 1.01.19.qxp_Layout 1 6/19/19 9:42 AM Page 1
LOG CRANE ADAPTER /
DRAWBAR KIT - Required for
use of LW228 Log
Crane when a
MRH35 or HRH35
Rear Hitch is
mounted. [Can also
be used alone
when you need a drawbar and
have a Rear Hitch mounted].
RUBBER TRACK SHOE KIT -
Medium-duty rubber pavement shoes
allow “scratch free” travel on any sur-
face. Gives added penetration and trac-
tion. Ideal for snow use on blacktop or
concrete. Not for heavy, rocky condi-
tions. [Complete with all fasteners.]
Bolts to steel tracks.
MUD / ICE SCRAPER KIT - Pair of
“scraper arms” continually remove
rock chips, mud and snow build-up
from between track sprockets. (For
Steel Tracks only).
GROUSER TRACK SHOE KIT -
Heavy-duty “U” shaped all-steel shoes
give added penetration and traction to
track. Provides ultimate stiffness and
strength to track allowing use in rocky
conditions with the best possible trac-
tion. [Complete with all fasteners.]
Bolts to steel tracks.
HITCH EXTENDER KIT - Moves attach-
ment “mounting holes” of Front Hitch 6” for-
ward. Required for use with D1060
Backhoe and BK45 Material Bucket Kit.
MATERIAL BUCKET KIT (Hydro Dump) -
Front mounted, heavy-duty, 42-1/2” wide x
12-3/4” high x 13-1/2” deep, “hydro-dump-
ing”, hardened cutting edge, 350 lbs. rated
load... Rear “counterweight” required for
maximum loads. [Requires HFH15 Front
Hitch, PP35 Power Pack and HE47 Hitch
Extender]
MATERIAL BUCKET KIT (Manual Dump)
- Front mounted, heavy-duty, 42-1/2” wide x
12-3/4” high x 13-1/2” deep, manual dump-
ing, hardened cutting edge, 350 lbs. rated
load... Rear “counterweight” required for
maximum loads. [Similar to BK45 Material
Bucket above, but without the “hydro-dump-
ing” features].
BUCKET FORKS KIT -
Four, 25” long, 19” high, 2-
1/2” wide x 1/2” thick solid
steel forks quickly mount to
BK44 or BK45 Material
Buckets with eight locking
bolts. [Requires BK44 or
BK45 Material Bucket].BLADE DRAWBAR KIT - Mounts to “top
lip” of DB44 Dozer Blade... see “inset”
Photo above. Use for medium-duty pulling,
has 3/4” hole for tow hook or chain clevis.
[Requires drilling four 5/16” holes in Blade].
BladeDrawbar
REAR DRAWBAR KIT - Mounts to rear of
tractor at two levels: Drawbar
can be 5-1/2” or 10-1/2”
above ground. [Can not be
used while any rear attach-
ment is mounted].
TRACK MAT KIT - Two
(2) 18” wide x 1/2” thick x
96” long rubber mats.
Use as protective
padding when driving
steel tracks over concrete
walks and drives or to
protect parking spot in
garage.
MANUAL REAR HITCH KIT -
Available with standard “sleeve
hitch” and two “lift-assist”
springs. Comparison for judging
ability of “lift assist” springs: 2
lbs. of lift handle force will raise
24 lb. DR30 Ripper. [includes
basic Drawbar shown]
HITCH ADAPTER KIT -
Mounts to Rear Hitch with two
bolts. Allows use of dozens of
2” Receiver Tube Attachments.
THREE SHANK RIPPER KIT -
Three 17” long x 2” wide x 5/8” thick
“hardened steel” ripping teeth. May
be used singlely or all three together.
Design allows to flip tooth for greater
wear. [Recommended for RS1000]
DOUBLE SHANK RIPPER KIT -
Two 17” long x 2” wide x 5/8” thick
“hardened steel” ripping teeth. May
be used singlely or both together.
Design allows to flip tooth for greater
wear. [Recommended for MD196K]
STEEL RAKE KIT - Unique “finishing rake”
using thirty-seven “log nail” teeth mounted in
42” wide frame. Takes place of hand raking
operations. NOT for ripping. NOT for use with
PP35 Power-Pack! [Requires MRH35 or
HRH35 Rear Hitch].
LOG CRANE KIT - Heavy-duty
rear mounted crane with 800
lbs. winch pulling capacity.Does
not include
winch. Use LW16
Manual Winch
at right...
Has self-
contained
drawbar.
The MAGNATRAC® RS1000 is offered completely assembled and painted. The MINI-DOZER® MD196K is completely manufactured but sold in an
unassembled, unpainted KIT form. It’s the customer’s responsibility to provide competent service ability! The servicing can be provided either by
the mechanically inclined customer, or by a local mechanic. All Attachments and Accessories [unless noted otherwise] are shipped in an easy-
to-assemble KIT form. We provide Manuals & collateral material for complete service and repair so that anyone with reasonable mechanical skill
can perform all required service work. Contact the factory for more information.
The STRUCK CORP. has a policy of continuous product improvement and reserves the right to change its products, specifications and dimensions
at any time without notice or obligation. All dimensions and specifications are based upon best possible performance of components, running at
100% efficiency. Results will vary due to changes due to component wear, oil temperature, etc. If a particular specification or dimension is critical to
your application, contact the factory for more detailed information.
Struck Corp. W51N545 Struck Lane P.O. Box 307 Cedarburg, WI 53012
E-Mail: [email protected] Phone: 262-377-3300 Web: www.StruckCorp.com Fax:262-377-9247ll l
l l l
HYDRO FRONT HITCH KIT - All hy-
draulic Front Hitch provides operator
with full power to drive a mounted
Dozer Blade or Bucket into tough soil,
gravel, manure, sand etc. with total
control. Includes: cylinder, hoses, fit-
tings & mounting hardware. [Requires
PP35 Power Pack].
Attachments... for MD196K & RS1000 [Continued] Attachments... for MD196K & RS1000 [Continued]
Manual Rear Hitch
Log Crane Adapter
Drawbar
Three Shank Ripper
Steel Rake
Double ShankRipper
Grouser Shoes
Hitch Adapter
Rear Drawbar
Track Mat
Log Crane
Bucket Forks
Rubber Shoes
Hydro Front Hitch
Box Scraper[shown mounted toDozer Blade]
MD196K-MRH35MRH35
MD196K-LCA9LCA9
TR23
MD196K-RK26RK26
HFH15
BK44
BK45
BF22
HE47
BS40
TSO58
MD196K-HA14HA14
MD196K-BD23BD23
MD196K-BD7BD7
TM96LW16
MD196K-LW228LW228
MD196K - MS90MS90
RS58
MD196K-DR30DR30
*
*
*
**
*
*
*
*
*
*
BOX SCRAPER KIT - Attaches to DB44 Dozer Blade to
trap and move loose material. 42” wide x 12+” deep x 18+”
high. Hardened and beveled “plow steel” cutting edge.
[Requires DB44 Dozer Blade; shown above mounted to
DB44 Dozer Blade]
DB44 DOZER BLADE
DB44 DOZER BLADE
MaterialBucket Kit(Hydro Dump)
Attachments... for RS1000 with Hydro Power Pack!
*Unassembled,Unassembled,Unpainted KIT Unpainted KIT
23
MANUAL WINCH KIT -
Utility winch,
800 lbs. pull capacity,
5/32” dia. x 25 ft.
long cable with
hook. [Requires
LW228 Log Crane
or mounting location
provided by customer].
Contact factory for
Electric Winches. Manual Winch
Mud/Ice Scraper
MaterialBucket Kit(Manual Dump)
Hitch Extender
Buy-Guide MD196K & RS1000 1.01.19.qxp_Layout 1 6/19/19 9:43 AM Page 2