Atlas Copco Exploration Products Boyles C6/C6C core...
Transcript of Atlas Copco Exploration Products Boyles C6/C6C core...
Atlas Copco Exploration Products
Boyles C6/C6C core drilling rig
Technical specification
Flexible enough to take on almost any jobThe Boyles C6 surface core drilling rig is part of the Boyles range, a new generation of Atlas Copco quality drilling rigs that combine produc tivity with a favorable life cycle cost. Boyles C6 repre sents the most flexible rig size in the Boyles range and is available in trailer-mounted (Boyles C6) or crawler-mounted (Boyles C6C) versions.
Safe and ergonomic• Two E stops on the drill unit are standard and Boyles C6C
has another E stop for the Radio Remote Control.
• Drill operators are protected from the rotation unit by a safety cage.
• Possible to operate by feel while focusing on the drilling operation, thanks to the operator friendly control panel.
Flexible drilling rig size • Compact structure, giving excellent space utilization
using fitted modules.
• Foldable 2-section mast simplifies short-distance transport of the rig.
Reliable and powerfulBoth the Boyles C6 and Boyles C6C are equipped with:
• A powerful main hoist.
• A rod holder with a long-life gas cartridge that handles rods from BO to PO size and casing up to HW.
• A proven and reliable rotation unit with 4-speed gear box that can generate the high rates of penetration with very high torque when it is required.
• A reliable power unit, Cummins QSB 6.7 Tier III (153 kW), which brings out the full capacity of the rig, resulting in higher penetration rates to the bottom of the hole.
Radio remote controlled (Boyles C6C)The tramming functions of the rig can be precisely controlled from a safe distance, eliminating the danger of being on or next to the machine while in motion. If radio contact is lost, tramming will stop automatically.
2
Specifications
Main hoist
The powerful main hoist, equipped with a hydraulic motor and a dual brake system, ensures a well-con-trolled speed. The dual brake system offers both dyna mic and static break-ing. When the lifting operation is stopped, firm self-locking is applied.
Single line capacity Bare drum: 80 kN (18 000 lb)
Line speed Bare drum: 44 m/min (148 ft/min)
Cable size 27 m (89 ft) x 16 mm (10/16 in)
Wireline hoist
The wireline hoist has a high level of speed control to ensure safe and consistent opera tion.
Capacity1,830 m (6 000 ft) of 4.76 mm (3/16 in)
975 m (3 200 ft) of 6.35 mm (1/4 in)
Line pullBare drum: 11.9 kN (2,665 lb)
Full drum: 3.0 kN (668 lb)
Line speedBare drum: 114 m/min (374 ft/min)
Full drum: 453 m/min (1 486 ft/min)
Mast and feed system
Feed travel 3.5 m (11.5 ft)
Feed speeds Fast and slow with variable control
Thrust 59.6 kN (13 390 lb)
Pull 138 kN (31 020 lb)
Drilling angle 45 to 90 degrees
Rod pull length 6.09 m (20 ft)
Power unit
Manufacturer Cummins
Model QSB6,7 Tier III
Volume 6.7 liter 6 cyl.
Power 153 kW (208 hp)
RPM 1 800
Engine type Diesel turbocharged/after cooled
Cooling Water
Electrical system 24 V (alternator 24 V, 95 Amp)
Hydraulic system
Primary pump 28 MPa – 242 l/min (4,061 psi – 63.9 gal/min)
Secondary pump 20 MPa – 122 l/min (2,901 psi – 32.2 gal/min)
Auxiliary pump 21.5 MPa – 47 l/min (3,118 psi – 12.4 gal/min)
Hydraulic oil cooling Air
Rotation unit
The rotation unit can handle BO-PO rods and BW-HW casing. It consists of a hydraulic motor, a sealed gear-box, a hollow spindle and an Atlas Copco patented hydraulic chuck, and quick change chuck jaws. The rotation speed is adjustable from the control panel.
Power Hydraulic motor – variable speed/reversible
Final drive 4 in chain driven in oil bath – 2,5 ratio
Spindle (inner diameter) 117 mm (4 5/8 in)
Spindle data
Ratio Speed, rpm Torque, Nm Torque, ftlb
1st 6.63:1 117–196 5 113–3 051 3 771–2 250
2nd 3.17:1 245–410 2 445–1 459 1 803–1 076
3rd 1.72:1 451–756 1 326–792 978–584
4th 1.00:1 776–1 300 771–460 569–340
Range selection Manual control from operator’s station
Hinged head Swing away
Chuck assemblyType Hydraulically opened, spring closed
Maximum inside diameter 117 mm (4 5/8 in)
Holding capacity 18 143 kg (40 000 lb)
Rod Holder
The rod holder is hydraulically opened and closed by gas pressure. In case of loss of hydraulic pressure, the rod holder closes instantly. The gas pressure can be conveniently monitored.
Type Hydraulically opened, gas spring closed
Maximum inside diameter 210 mm (8,3 in)
Holding capacity 13 000 kg (28 660 lb)
3
Standard equipment
Hydraulic mast dump
Mast in two sections
Large crown sheave wheel
Wear lines on lower mast
Safety guards
Hydraulic oil reservoir fill pump and filtration
Tier III diesel engine
Control panel
Hydraulic P-size rod holder
4 hydraulic leveling jacks
Fuel tank 200 l (53 gal)
Fuel filter and water separator
Hydraulic mast raise
Feed wear protection plates
Lighting kit
E-stop devices
Spindle tachometer
Drill base supports
Boyles C6 and Boyles C6C
Support 4 hydraulic jacks
Pad diameter 200/230 mm (7.87/9 in)
Travel length 550 mm (21.6 in)
Boyles C6 Trailer mounted rig, four 770 mm (30.3 in) wheels, towing package
Boyles C6C
Crawler mounted rig, radio remote controlled
Max speed 3.3 km/h
Heavy duty crawler tracks 300 mm wide
Optional equipment
Hydraulic mud mixer
Water flow meter Max 6.4 MPa
Hydraulic mud pump, Trido 140 140 l/min (37 gal/min) / 7 MPa (1 015 psi)
High altitude kit
Atlas Copco Geotechnical Drilling and Exploration www.atlascopco.com
© C
opyr
ight
201
2, A
tlas
Cop
co C
rael
iuss
AB
, Mär
sta,
Sw
eden
. All
prod
uct n
ames
in th
is p
ublic
atio
n ar
e tra
dem
arks
of A
tlas
Cop
co. A
ny u
naut
horis
ed u
se o
r cop
ying
of t
he
cont
ents
or a
ny p
art t
here
of is
pro
hibi
ted.
Thi
s ap
plie
s in
par
ticul
ar to
trad
emar
ks, m
odel
deno
min
atio
ns, p
art n
umbe
rs a
nd d
raw
ings
. lllu
stra
tions
and
pho
tos
in th
is b
roch
ure
may
sho
w e
quip
men
t with
opt
iona
l ext
ras.
Spe
cific
atio
ns a
nd e
quip
men
t sub
ject
to c
hang
e w
ithou
t not
ice.
Con
sult
your
Atla
s C
opco
Cus
tom
er C
ente
r for
spe
cific
info
rmat
ion.
6991
175
6 01
Mär
sta,
Sw
eden
, Nov
embe
r 201
2
Measurements and weights
Weight
Boyles C6 incl. Trido140 7 000 kg (15 430 lb)
Boyles C6C incl. Trido140 9 000 kg (19 838 lb)
A B C
D
E
F
G
H
I
45 °
90 °
A
DC
B
E
A
B C
D
E
G
H
45 °
90 °
A
C D
B
EBoyles C6
Boyles C6
Boyles C6
Boyles C6C
Boyles C6C
Boyles C6C
Working dimensionsBoyles C6 Boyles C6C
Dimension mm in mm in
A 10 082 397 10 082 397
B 7 294 287 7 541 297
C 9.5 0.4 256.5 10.1
D 196.5 7.7 87 3.4
E 7 486 295 7 486 295
Capacity drilling depthBoyles C6 and Boyles C6C
m ft
B Wireline 1 540 5 052
N Wireline 1 200 4 042
H Wireline 800 2 695
P Wireline 475 1 558
Depth are based on vertical hole
Transport dimensionsBoyles C6 Boyles C6C
Dimension mm in mm in
A 222 8.7 321 12.6
B 2 205 87 2 634 104
C 2 602 102 2 817 111
D 6 525 257 5 302 209
E 2 625 104 2 555 101
F 379.5 14.9 – –
G 3 400 134 4 905 193
H 705 28 705 28
I 1 927 76 – –