Assembly & Parts Manual · casting. Slide casting bushing , spring , rod sleeve , spring washer...
Transcript of Assembly & Parts Manual · casting. Slide casting bushing , spring , rod sleeve , spring washer...
Assembly and Parts Manual
Detracker
Manufacturing, Inc.www.greatplainsmfg.com
EN
Read the operator’s manual entirely. When you see this symbol, thesubsequent instructions and warnings are serious - follow withoutexception. Your life and the lives of others depend on it!
Illustrations may show optional equipment not supplied with standard unit.
41541
© Copyright 2014 Printed 02/24/2014 589-386Q
Great Plains Manufacturing, Inc. iii
Table of Contents
General Information .....................................................1Tools Required ...............................................................1Pre-assembly Checklist..................................................1Document Family ...........................................................1
Product Support......................................................1Assembly ......................................................................2Before You Start.............................................................2Install Detracker Frame Assembly .................................2
Detracker Frame Assembly Parts...............................2Install Detracker Spring Assembly .................................3
Detracker Spring Assembly Parts ................................. 3Install Coulter Hub Assembly......................................... 4Coulter Hub Assembly Parts.......................................... 4Prior Going To The Field................................................ 5
Detracker Placement.............................................. 5Detracker Adjustments........................................... 5Spring Adjustment.................................................. 5Detracter Height Adjustment .................................. 5
Torque Value Chart........................................................ 6
02/24/2014 589-386Q
© Copyright 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014 All rights Reserved
Great Plains Manufacturing, Inc. provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has beentaken in the preparation of this manual, Great Plains Manufacturing, Inc. assumes no responsibility for errors or omissions. Neither is any liability assumed fordamages resulting from the use of the information contained herein. Great Plains Manufacturing, Inc. reserves the right to revise and improve its products asit sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future.
Trademarks of Great Plains Manufacturing, Inc. include: Singulator Plus, Swath Command, Terra-Tine.Registered Trademarks of Great Plains Manufacturing, Inc. include:
Air-Pro, Clear-Shot, Discovator, Great Plains, Land Pride, MeterCone, Nutri-Pro, Seed-Lok, Solid Stand,Terra-Guard, Turbo-Chisel, Turbo-Chopper, Turbo Max, Turbo-Till, Ultra-Till, Verti-Till, Whirlfilter, Yield-Pro.
Brand and Product Names that appear and are owned by others are trademarks of their respective owners.
iv Detracker Great Plains Manufacturing, Inc.
589-386Q 02/24/2014
Great Plains Manufacturing, Inc. 1
General Information
These Instructions explain how to install the Detracker onthe front of the center gang hanger. The unit will beshipped with the detracker mounts banded together. Theutility coulters will be pre-assembled from the factory. Therest of the smaller parts will be shipped in a box.
Tools Required• Basic Hand Tools
• Torque Wrench
• Fork Truck, Overhead Hoist or Loader
Pre-assembly Checklist1. Before assembling, read and understand “Important
Safety Information” in front part of the machinesOperator’s Manual.
2. Have at least two people on hand while assembling.
3. Make sure area is level and free of obstructions(preferably an open concrete area).
4. Have all major componets
5. Have all fasteners and pins shipped with Detracker.
6. Be sure and have a copy of all manuals of themachine you are mounting the Detracker on.
Document Family
7. If you do not have a copy of all the manuals that per-tains to your machine, you may go to www.great-plainsmfg.com and all the manuals will be online.
8. If you need further assistance after reading all themanuals, assistance is available. Contact:
Product SupportGreat Plains Mfg., Inc., Service Department
PO Box 5060Salina, KS 67402-5060
589-386Q Assembly & Parts Manual (this document)
586-201Q Assembly Manual
586-201M Operator Manual
586-201P Parts Manual
586-229Q Assembly Manual
586-239M Operator Manual
586-239P Parts Manual
Figure 1Detracker
41628
02/24/2014 589-386q
2 Detracker Great Plains Manufacturing, Inc.
Assembly
Before You StartReview these instructions, and make sure you under-stand where and how the componets install to machine.
Carefully un-band all componets and inventory the con-tents on page.Assembly
Install Detracker Frame AssemblySee parts lists below for proper descriptions and comments.
Refer to Figure 21. Attach detracker mount to center gang hanger
with plate , using bolts , lock washers andnut . See “Prior Going To The Field” on page 5,for proper placement. Repeat same procedure forother side.
2. Mount shank to detracker mount tube by aligningthe holes in the two plates (one on each side).Align holes in shank clamps on front side ofshank, secure assembly with bolts and lockwashers . These bolts thread into shank clamp.See “Prior Going To The Field” on page 5, forproper placement.
3. Now the set screws may be installed into theshank clamps. Attach bolt through top hole inshank, secure with lock nut .
4. Once every thing is adjusted, all bolts may be tight-ened to specs, See “Torque Value Chart” onpage 6.
Detracker Frame Assembly Parts
Callout Part Number Description Comment11 589-384H DETRACKER MOUNT12 589-134D PART - DETRACKER13 802-208C HHCS 5/8-11X8 GR514 804-022C WASHER LOCK SPRING 5/8 PLT15 803-021C NUT HEX 5/8-11 PLT16 204-026D SHANK 1 1/2D X 22 FERT COUL17 204-038D CLAMP PLT 4 BAR18 802-045C HHCS 1/2-13X5 GR19 804-015C WASHER LOCK SPRING 1/2 PLT20 204-072D CLAMP SHANK 1 1/2 DIA21 801-040C SCREW SQ HD 5/8-11 X 1 CUP P22 802-115C HHCS 5/16-18X2 GR523 803-011C NUT LOCK 5/16-18 PLT
Figure 2Detracker Frame Assembly
41629
13
1812
141511
19
1716
21
20
22
23
1112 13 14
15
1617
2018
19
2122
23
589-386q 02/24/2014
Great Plains Manufacturing, Inc. Assembly 3
Install Detracker Spring AssemblyRefer to Figure 25. Slide coulter stop weldment into slot in swivel
casting and onto shank, secure with roll pin .Install set screw into coulter stop weldment.Attach set screws and jam nut into swivelcasting.
6. Slide coulter spring rod through hole on swivelcasting. Slide casting bushing , spring , rodsleeve , spring washer over coulter spring rodand secure with two jam nuts . Tighten first jamnut down until it compresses spring down to97⁄8 inches to 10 inches as shown. Tighten secondjam nut down tight against first one.
7. Be sure swing arm bushing is in the swing arm the right way. Also check that the swivel casting
bushing is installed. Slide swing arm on to rest ofassembly as shown, secure top with flange lock nut
and jam nut . Secure pin with flat washerand cotter pin .
8. If decal is not installed, note location, clean area,peel backing off and press on firmly.
9. See “Prior Going To The Field” on page 5, forproper adjustments after hub assembly is installed.before tightening bolts.
Detracker Spring Assembly Parts
Figure 3Spring Assembly
42824
27
28
29
30
31
3233
35
38
34
25
24 3940
41
36
37
26
2624 29
2127 28
3839 40
41 4237
3132
30
36 37 3435
33
Callout Part Number Description Comment24 249-225S PVT CLTR CASTING MNT ASY RH25 800-001C GREASE ZERK STRAIGHT 1/4-2826 149-044D COULTER STOP 30 DEGREE27 801-083C SCREW SET 5/8-11X1 1/2 GR8 CU28 803-023C NUT HEX JAM 5/8-11 PLT29 805-043C PIN SPIROL 3/8X2 1/2 PLAI30 804-156C WASHER MACH 1 1/4x3/4x14GA31 817-513C BUSHING 1x3/4x1 1/8 FLG HD32 204-664H 20” CLTR SWING ARM WLMT33 838-482C DECAL GP PLANTING COMPONENT34 804-165C WASHER MACH 1 7/8x1 1/4x14GA35 800-164C SNAP RING 3/4 EXTERNAL HEAVY36 800-177C SNAP RING EXT 1 1/4 HEAVY37 803-048C NUT HEX JAM 3/4-10 PLT38 802-718C EYE BOLT 3/4-10x14 3/4 LG SP39 805-331C COULTER SPRING GUIDE TUBE40 149-559D SPRING 2.25 O.D. X .5 COIL41 149-558D COULTER SPRING WASHER
02/24/2014 589-386q
4 Detracker Great Plains Manufacturing, Inc.
Install Coulter Hub AssemblyRefer to Figure 4The hub assembly should come pre-assembled on swingarm. Figure 4 shows a parts breakdown if you have totake the assembly apart.
10. Align holes on coulter blade to bolts on hubassembly , secure with lock washers andnut .
11. Tightened hub bolts to specs, See “Torque ValueChart” on page 6.
Coulter Hub Assembly Parts
19
51
50
47 45
48 49
4546
52
25
43
4253
44
45
42
Figure 4Coulter Hub Assembly
43297
5143 19
52
Callout Part Number Description Comment42 822-020C BRG CUP LM-6701043 200-039V COULTER HUB & CUP ASSY Includes items 25 & 4344 816-009C OIL SEAL DOUBLE LIP45 822-021C BRG CONE 1.25ID LM-6704846 200-001D HUB GREASE CAP47 204-379S COULTER HUB PACKAGE Includes items 25, 43-4748 804-055C WASHER SPINDLE - 7/849 803-029C NUT HEX SLOTTED 7/8-14 PLT50 805-017C PIN COTTER 3/16 X 1 3/4 PLT51 820-215C 18 INCH TURBO COULTER BLADE52 803-020C NUT HEX 1/2-13 PLT53 802-214C RHSNB 1/2-13X1 1/4 GR5
589-386q 02/24/2014
Great Plains Manufacturing, Inc. Assembly 5
Prior Going To The FieldDetracker Placement
Refer to Figure 5Adjust detracker frames to approximate location asshown in Figure 5 to clear other parts on machine. Adjustcoulter assemblies to cover tire tracks.
Detracker Adjustments
Refer to Figure 6Spring Adjustment12. Coulters springs are preset at 10”, giving the
coulters an initial operating force of 400 pounds.This setting is adequate for many no-till conditions.For lighter no-till conditions where rocks or otherobstructions are a problem, you can lengthen thesprings to protect the coulters from impact.
Note: Setting the coulter spring length shorter than 9.75”may contribute to premature failure of parts andvoids the warranty.
Detracter Height Adjustment13. The initial height of the detracker coulter assemblies
is 1 1/2” - 2” deeper than the machine gangs. Toadjust the height, loosen the set screws on theclamp shanks and slide the shank up or down tothe desired height, then re-tighten set screws.
Note: May need to adjust coulter height for different fieldconditions.
14. Be sure all bolts are tightened to specs, See“Torque Value Chart” on page 6.
15. This completes the setup.
Spring Length Force10.25” (26.04cm) 300lbs (136kg)
10” (25.4cm) 400lbs (181kg)9.75” (24.77cm) 525lbs (238kg)
Figure 5Detracker Placement
41630
Figure 6Detracker Adjustment
41627
2120
02/24/2014 589-386q
6 Detracker Great Plains Manufacturing, Inc.
Torque Value Chart
94 6
25199m
BoltSize
Bolt Head IdentificationBoltSize
Bolt Head Identification
Grade 2 Grade 5 Grade 8 Class 5.8 Class 8.8 Class 10.9in-tpia N-mb N-m N-m mm x pitchc N-m N-m N-m1⁄4-20 7.4 11 16 M 5 X 0.81⁄4-28 8.5 13 18 M 6 X 1 7 11 155⁄16-18 15 24 33 M 8 X 1.25 17 26 365⁄16-24 17 26 37 M 8 X 1 18 28 393⁄8-16 27 42 59 M10 X 1.5 33 52 723⁄8-24 31 47 67 M10 X 0.75 39 61 857⁄16-14 43 67 95 M12 X 1.75 58 91 1257⁄16-20 49 75 105 M12 X 1.5 60 95 1301⁄2-13 66 105 145 M12 X 1 90 105 1451⁄2-20 75 115 165 M14 X 2 92 145 2009⁄16-12 95 150 210 M14 X 1.5 99 155 2159⁄16-18 105 165 235 M16 X 2 145 225 3155⁄8-11 130 205 285 M16 X 1.5 155 240 3355⁄8-18 150 230 325 M18 X 2.5 195 310 4053⁄4-10 235 360 510 M18 X 1.5 220 350 4853⁄4-16 260 405 570 M20 X 2.5 280 440 6107⁄8-9 225 585 820 M20 X 1.5 310 650 900
7⁄8-14 250 640 905 M24 X 3 480 760 1050
1-8 340 875 1230 M24 X 2 525 830 1150
1-12 370 955 1350 M30 X 3.5 960 1510 2100
11⁄8-7 480 1080 1750 M30 X 2 1060 1680 2320
11⁄8-12 540 1210 1960 M36 X 3.5 1730 2650 3660
11⁄4-7 680 1520 2460 M36 X 2 1880 2960 4100
11⁄4-12 750 1680 2730
13⁄8-6 890 1990 3230 a. in-tpi = nominal thread diameter in inches-threads per inch
13⁄8-12 1010 2270 3680 b. N· m = newton-meters
11⁄2-6 1180 2640 4290
11⁄2-12 1330 2970 4820
c. mm x pitch = nominal thread diameter in mm x thread pitch
Torque tolerance + 0%, -15% of torquing values. Unless otherwise specified use torque values listed above.
5.8 8.8 10.9
589-386q 02/24/2014
02/24/2014 589-386Q
Great Plains Manufacturing, Inc.Corporate Office: P.O. Box 5060Salina, Kansas 67402-5060 USA