Assembly Manual - Infrared Saunas Au

Assembly Manual

www.infraredsaunas.co.nz Tel 021 224 8020


Prepare & Position the Sauna FloorIf you are assembling your sauna ona hard surface floor it isrecommended that you apply theincluded adhesive felt pads to thebottom of the sauna floor.

Place the sauna floor in the desired location. It is necessary to position the floorout from your walls for assembly and move the sauna following assembly.

It is important that the sauna floor is level. Checking with a large level isrecommended. If the floor is not level, shimming or other remediesshould be applied before assembling the sauna.


Left Side WallPlace the left side wall on your floorbehind the sauna floor base.

Front Wall Insert the front wall (with window) into

the channel in the sauna floor base


Connect Left Side Walland Front WallCinch the left side wall andthe front wall together byapplying pressure onthe outside of the side wallwith your knee whileassistant gently pushesthe edge of front wall withtheir foot.Slide the front wall upwardapprox. 3/4” with right handwhile holding the side walldown with your left hand.

There are two sets of fasteners to jointhe saunas' corners together. Afterlowering the front wall, check to ensurethat both sets of fasteners haveconnected by looking at the cornerinside of the sauna. It is possible toconnect one set of fasteners and missthe other. If there is an obvious gap inthe corner between the two walls thefasteners have not connected and theraising and lowering procedure willneed to be repeated.


Back WallRepeat the procedure toconnect the back wall tothe left side wall

Right Side Wall (with door)Insert the right side wall into thechannel in the sauna floor base


Connect the Right Side Wall(door wall) to Back Wall

It is easiest to connect one corner ofthe side wall (door wall) at a time

.It is recommended that the assistantstablizes the sauna on opposite side

while connecting the door wall

Connect the Right Side Wall(door wall) to the Front Wall


Connect the front wall heater electricallead to the floor base.Ensure hat the threaded cuff of theconnector is fully screwed onto the floorbase connector.

UnderBench ElectricalConnect all electrical

cords to the main powersupply box recessed in

the floor.


Remove Side WallHeater Guards

The wooden lattice work in front ofthe heaters is referred to as theheater guard. These are held in

place with strong magnets.It is necessary to remove the heater

guards from the two side walls inorder to install the leg heater

and the sauna bench.

Leg HeaterInstall the leg heater by lowering it intothe holding brackets mounted on theside walls.Plug leg heater into the power supplybox in floor.


Install the Sauna Bench

Reinstall the Side WallHeater Guards


Prepare the Sauna RoofRemove the one panel on the

left side of roof to accesselectrical connections.

Install Sauna RoofLower the roof into place by firstfitting the right side of roof (doorside).Keep the left side of roofelevated to enable feeding ofelectrical connection from wallthrough the roof.


This is easiest accomplished with one person holding the weight of the roof whilethe other feeds the wire through the hole.When the wire is fed entierly through the roof, lower roof into place taking carenot to pinch the wire between the roof and the front wall

Roof WiresBefore lowering the roof itis necessary to feed thewire up through thehole in the sauna roof aspictured.

Roof ElectricalTake the wire that was fed from the side wall through the roof and makeconnection on the roof. This connection is the 12 volt power for the LEDreading light and the Bluetooth audio receiver/ amplifier.


Bluetooth Audio ReceiverMusic can be piped to thespeakers in the sauna twodifferent ways, either wirelessvia the Bluetooth receiver or bydirectly connecting your device(smart phone, tablet, laptop etc.)with an audio cord (red audiocord not included)

Bluetooth Mode: Search for and pair your device's Bluetooth to 'BT speaker'.

Direct Connect Mode: Connect your device to

the saunas' speakers viayour device's headphonejack by inserting an audio

cord into the BTcircuit board. This will

deactivate the Bluetoothreceiver.


Reinstall the roof panelsand feed youraudio cord through thehole in roof if youhave decided NOT to useBluetooth


Control Panel


Interior Control Panel

Temperature Sensor FRAGILE

DO NOT TOUCH


Connecting the sauna to your house power supplyWhen the sauna is plugged into you wall outlet the red Power Indicator light on the controlpanel will be on. The Bluetooth audio receiver on the roof will make a beeping noise its indicator light will turnon.

ON/OFF for HeatersPush the POWER button to turn the sauna heaters ON. The various displays will come on.The sauna heaters will remain ON until the timer runs down to 00.The sauna heaters can be turned OFF at any time by pushing the POWER button.

Timer AdjustmentThe default time is 60 minutes. Press + or to change the Timer setting. The maximum setting is 60 minutes. The minimum setting is 5 minutes.

Pre HeatSun Stream Infrared Saunas are typically used by preheating the sauna for 2030 minutes.

Thermostat AdjustmentPress + or to change the Thermostat setting.Increase Thermostat Setting: Press the + button to increase the temperature by 1 degree Cincrements. The maximum setting is 65 C.

Decrease Thermostat Setting: Press the button to decrease the temperature by 1 degree Cincrements.The minimum setting is 25 C.


Thermometer /Thermostat DisplayWhen the POWER button is turned ON the digital display will show the Thermometer reading. Anytime the + and buttons are pushed the Thermostat setting display will show.After setting the thermostat the display will return to displaying Thermometer reading.

Temperature ControlWhen the interior air temperature is below the Thermostat set temperature, the heaters willremain ON.

When the interior temperature is higher than the Thermostat set temperature, the power to theheaters will be turned OFF. The heater panels will begin to cool down, air temperature andInfrared levels will slowly drop until the Thermostat is activated and the power to the heaterswill be turned back on.

AII (Adjustable Infrared Intensity)The Intensity button on the control panel will adjust the Infrared intensity much like a dimmerswitch for a household light. Press the Intensity button to select 100%, 75% or 50 % levels ofInfrared intensity for different purposes and individual needs.


Enjoy your newSun Stream

Infrared Sauna !

Assembly Manual - Infrared Saunas Au

Documents

Transcript of Assembly Manual - Infrared Saunas Au