Assembly Instructions for Model: VMPR1Thank you for choosing a Sanus Systems Model: VMPR1 ceiling mount. The VMPR1 ceiling mount provides a unique, simplified method of ceiling mounting inverted LCD/DLP projectors. Its low profile design offers roll, pitch, and yaw adjustment. The VMPR1 steel-to-steel construction with adjustable height to maintain proper ventilation, hold registration for quick lamp changes and easy filter cleaning without loosing registration. The VMPR1 ceiling mount includes an NPT Extension Pipe that may be used where more room is required, such as areas with vaulted or cathedral ceilings.

WARNING: The maximum weight to be installed on the VMPR1 ceiling mount is 50 pounds [22.68 Kg]. Improper installation may result in serious personal injury. Make sure the structural members can support a redundant weight factor five times the total weight of the equipment. If the structure can not support this weight, reinforce the structure prior to installing the VMPR1.

If you do not understand these directions, or have any doubts about the safety of the installation, please call a qualified contractor or contact Sanus at 800.359.5520 or www.sanus.com. Check carefully to make sure that there are no missing or defective parts. Our customer service representatives can quickly assist you with installation questions and missing or damaged parts. Replacement parts for products purchased through authorized dealers will be shipped directly to you. Never use defective parts. Do not use this product for any purpose that is not explicitly specified by Sanus Systems. Please call Sanus Systems before returning products to the point of purchase.

Required Tools: Open End Wrenches, Phillips screwdrivers, Allen Wrenches (provided), other tools may be required depending on the method of installation.

Supplied Parts and Hardware: (All threaded fasteners are shown full size.)

Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 11.09.06 (6901-100023)Customer Service: 800.359.5520. See complementary Sanus products at www.sanus.com

Universal Projector Interface - AQty. 1

Extension Arm - BQty. 2

Ceiling Plate - CQty. 1

Adjustment Bracket - DQty. 1

Bottom Cover - GQty. 1

Top Cover - HQty. 1

NPT Extension Pipe - FQty. 1

NPT Adapter - EQty. 1

Cap Screw - IQty. 2

Tapered Nut - KQty. 4

Set Screw - JQty. 1

M3/M4 Washer - LQty. 4

Lag Bolt Washer - TQty. 2

M5/M6 Washer - MQty. 4

Lag Bolt - UQty. 2

Allen Key - WQty. 1

Allen Key - VQty. 1

VMPR1 Dimensional Drawings

[470.15 mm]18.51 in

Covering area with Extension Arms (B)

installed

[305 mm]12.01 in

Covering area without Extension Arms (B)

installed

[117.3 mm]4.62 in

TO[100.076 mm]

3.94 in

M3 x 10 mm - OQty. 4

M6 x 12 mm - RQty. 4

M5 x 12 mm - QQty. 4

M4 x 12 mm - PQty. 4

M6 x 8 mm - SQty. 2

Set Screw - NQty. 1

Step 1: Ceiling Preparation

NOTE: Study the following information and adapt it as necessary to fit your specific installation.

WARNING: The maximum weight to be installed on the VMPR1 ceiling mount is 50 pounds [22.68 Kg]. Improper installation may result in serious personal injury. Make sure the structural members can support a redundant weight factor five times the total weight of the equipment. If the structure can not support this weight, reinforce the structure prior to installing the VMPR1.

Determine the position of the mount and its distance from the screen. This will require knowing the lens to screen distance. This information is normally listed in the projector specifications for set-up.

The hardware provided with the VMPR1 is designed to be secured to a wood framing member. For installations other than this, consult a qualified contractor. Use a high quality Stud Sensor to locate a stud in the area that you plan to mount the VMPR1 as shown in Diagram 1A. Verify the stud location with an awl or thin nail.

NOTE: Do not attach the Ceiling Plate (C) at this time.

Flat Ceilings: Align the Ceiling Plate (C) with the two tabs aligned to the screen as shown in Diagram 1B.

Pre-drill a 3 in [76.2 mm] deep hole in the center of the framing member using a 3/16 in drill; then, using the Ceiling Plate (C) as a template, pre-drill a second hole to the same depth.

Cathedral or Vaulted Ceilings: Align the Ceiling Plate (C) so that the NPT Adapter (E) is angled to allow the NPT Extension Pipe (F) to point straight down as shown in Diagram 1C.

Pre-drill a 3 in [76.2 mm] deep hole in the center of the framing member using a 3/16 in drill; then, using the Ceiling Plate (C) as a template, pre-drill a second hole to the same depth.

Diagram 1A

16 IN406.4 MM

StudSensor

Use awl or thin nailto verify center of framing member.

Use Stud Sensor to locate framing

member.

Tab toward screento allow adequatePitch Adjustment.

Diagram 1B(Shown assembledfor reference only.)

Diagram 1C(Shown assembledfor reference only.)

Tab aligned to allow NPT Extension Pipe (F)

to point down.

F

Step 2: Attach Universal Projector Interface to Projector

Loosen, but do not remove the Acorn Nuts shown in Diagram 2A.

Place the Universal Projector Interface (A) on the projector, aligning the holes in the Adjustable Feet with the threaded holes in the projector and with the Threaded Suds in line as shown in Diagram 2A. If there are only three mounting points, remove one Leg from the Universal projector Interface by removing the Acorn Nut.

uds in line as shown in Diagram 2A. If there are only three mounting points, remove one Leg from the Universal projector Interface by removing the Acorn Nut.

If necessary, add Extension Arms (B) to the Universal Projector Interface (A) by removing the Adjustable feet and Installing them on the Extension Arms as shown in Diagram 2B.

Secure the Extension Arms (B) to the Universal Projector Interface, using the M6 x 8 mm (S) screws as shown in Diagram 2B.

Adjust the Adjustable Feet as shown in Diagram 2C, making sure to allow for proper air ventilation and keeping the Universal Projector Interface level with the projector. Some Adjustable Feet may need to be at different heights.

NOTE:If the mounting holes are closer than a five inch diameter, lower the feet all the way to allow the Threaded Stud to swing under the Ceiling Plate (C).

Determine the proper screw size and depth, M3 x 10 mm (O), M4 x 12 mm (P), M5 x 12 mm (Q), or M6 x 12 mm (R), and corresponding Washers (L, M) for projector mounting.

Using correct Screws (O,P,Q,R) and Washers (L,M), secure the back two legs of the Universal Projector Interface (A) to the projector; then, secure the front legs.

Move the Universal Projector Interface (A) to the center of gravity of the projector. You can locate the center of gravity by attempting to lift the projector straight up. If it feels like it wants to twist, move the Universal Projector Interface toward the heavy side. When the projector feels balanced, you have located the center of gravity.

ThreadedStuds

AcornNut

AcornNut

AdjustableFoot

Hex Nuton all

Adjustable FeetAdjustable

Foot

Diagram 2C

Install M6 x 8 mmScrew (S)

Remove Adjustable Foot and install here

Rotate Adjustable Foot left or right to increase or decrease length. Each rotation equals

0.625” [15.80 mm].

Hex Nuton all

Adjustable Feet

Step 3A: Attach Ceiling Plate to Adjustment Bracket - Flat Ceilings

NOTE: If the projector is being mounted in an area where it must be lower from the ceiling, such as areas with vaulted or cathedral ceilings, proceed directly to Step 3B - Attach Ceiling Plate to Adjustment Bracket using Extension Pipe and NPT Adapter - Vaulted or Cathedral Ceilings.

Place the Ceiling Plate (C) over the Adjustment Bracket (D), lining up the holes in both the Ceiling Plate and the Adjustment Bracket as shown in Diagram 3A; then, using the two Cap Screws (I) secure the Adjustment Bracket to the Ceiling Plate. Diagram 3A

I

I

D

C

Step 3B: Attach Ceiling Plate to Adjustment Bracket using Extension Pipe and NPT Adapter - Vaulted or Cathedral Ceilings

Place the Ceiling Plate (C) over the NPT Adapter (E), lining up the holes in both the Ceiling Plate and the NPT Adapter as shown in Diagram 3B.

Using the Allen Key (V) and the two Cap Screws (I), secure the Ceiling Plate (C) to the NPT Adapter (E).

NOTE:Set Screw (J) is shorter than Set Screw (N).

NOTE:When using the NPT Extension Pipe (F), the Set Screw (N) must point either toward or away from the screen. If a longer NPT Extension Pipe is required, custom lengths may be purchased from your local hardware store.

Thread the NPT Extension (F) into the NPT Adapter (E) and secure it with the Set Screw (J) as shown in Diagram 3B.

Thread the Adjustment Bracket (D) onto the NPT Extension (F); then, using Set Screw (N), secure the Adjustment Bracket (D) to the NPT extension (F) as shown in Diagram 3B.

Diagram 3B

E

CI

I

F

D

N

J

Step 4A: Attach VMPR1 Top Assembly to Ceiling and install Top Cover - Flat Ceilings

Using the Lag Bolts (U) and Lag Bolt Washers (T) secure the VMPR1 Top Assembly to the framing member at the location selected in Step 1: Ceiling Preparation.

CAUTION:Do not over tighten the lag Bolts (U). Tighten lag Bolts until they are pulled firmly against the ceiling Plate (C). If there is a layer of drywall or other material, this drywall or other material may not exceed 5/8 inch (15.8 mm) in thickness. Failure to heed this caution may result in property damage and/or personal injury.

Tighten the Lag Bolts (U) until the Ceiling Plate (C) is flush with the ceiling drywall.

Choose the desired color Top Cover (H) and simply slide it over the Adjustment Bracket (D) until it fits snugly onto the Ceiling Plate (C).

Diagram 4A

U U

TT

C

DH

Step 4B: Attach VMPR1 Top Assembly to Ceiling and install Top Cover - Vaulted or Cathedral Ceilings

Using the Lag Bolts (U) and Lag Bolt Washers (T) secure the VMPR1 Top Assembly to the framing member at the location selected in Step 1: Ceiling Preparation.

CAUTION:Do not over tighten the lag Bolts (U). Tighten lag Bolts until they are pulled firmly against the ceiling Plate (C). If there is a layer of drywall or other material, this drywall or other material may not exceed 5/8 inch (15.8 mm) in thickness. Failure to heed this caution may result in property damage and/or personal injury.

Tighten the Lag Bolts (U) until the Ceiling Plate (C) is flush with the ceiling drywall.

Loosen the Pitch Adjustment Screws on the NPT Adapter (E) and set the NPT Extension Pipe (F) so that it is facing down; then, retighten the Pitch Adjustment Screws.

Rotate the Adjustment Bracket (D) until the Set Screw (N) is facing the screen; then, tighten the Set Screw securing the Adjustment Bracket to the NPT Extension Pipe (F).

Choose the desired color Top Cover (H) and simply slide it over the Adjustment Bracket (D) until it fits snugly onto the Ceiling Plate (C).

Diagram 4B

U

ET

D

C

F

HN

Step 5: Add Projector

Once the desired position is located and all the Adjustment Screws are tightened, the projector may be removed for service and re-installed without losing registration by reversing the following procedure.

Loosely install the Tapered Nuts (K) with the tapered end down on the Studs of the Universal Projector Interface (A) as shown in Diagram 5A.

NOTE:The two halves of the VMPR1 attach by lifting the and rotating the Universal Projector Interface (A) so that the Threaded Studs with Tapered Nuts (K) rotate into the Vee Slots of the Adjustment Bracket (D) as shown in Diagram 5A. Once the desired position is located and the Tapered Nuts are tightened, the projector may be removed for service and re-installed without losing registration by simply rotating the projector.

Align the four Vee Slots of the Adjustment Bracket (D) with the Threaded Studs and Tapered Nuts (K) of the Universal Projector Interface (A); then, rotate the Universal Projector Interface until it is securely locked into the Vee Slots of the Adjustment Bracket (D).

Tighten the Tapered Nuts (K), securing the projector and Universal Projector Interface (A) to the Adjustment Bracket (D) as shown in diagram 5B. Diagram 5A

K

A D

K

A

D

Vee Slot

Diagram 5B

Step 6 - Projector Alignment

The VMPR1 can be adjusted for vertical elevation (Pitch), horizontal tilt (Roll), and rotation (Yaw).

Pitch AdjustmentLoosen the Pitch Adjustment Screws on both sides of the Adjustment Bracket (D) and adjust the projector to the desired Pitch; then, retighten the Pitch Adjustment Screws as shown in Diagram 6A.

Roll AdjustmentLoosen the Roll Adjustment Screws on both sides of the Adjustment Bracket (D) and adjust the projector to the desired angle and tilt; then, retighten the Roll Adjustment Screws as shown in Diagram 6A. Diagram 6A

Yaw AdjustmentLower the Top Cover (H) to expose the Lag Bolts (U). Loosen the Lag Bolts and adjust the projector to the desired angle or yaw; then retighten the Lag Bolts and snap the Top Cover (H) back into place as shown in Diagram 6B. Diagram 6B

Pitch Adjustment ScrewRoll Adjustment Screw

Lag Bolt (U)Lag Bolt (U)

Top Cover (H)

Step 7 - Attach Bottom cover

Flex the Bottom Cover (G) at the seam, just enough to fit it around the Adjustment Bracket (D). Align the seam in the least visible location, you may also stick a small piece of tape to the inside of the Bottom cover to secure the seam.

Diagram 7

G

CSAV, Inc. and its affiliated corporations and subsidiaries (collectively, “CSAV”), intend to make this manual accurate and complete. However, CSAV makes no claim that the information contained herein covers all details, conditions, or variations. Nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. CSAV makes no representation of warranty, expressed or implied, regarding the information contained herein. CSAV assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.