ASSEMBLY INSTRUCTION SHEET

ITEM# FP-1833-7-1SKU# 810392476DESCRIPTION: GREY GRAND FIREPLACECUSOTMER SERVICE NO.:1-888-878-8820Email:customerservice@gbtcorporation.com

Warning:1. Need at least two adults to assemble this fireplace.2. Assemble on soft , smooth surface to protect finish from beingscratched .3. DO NOT use power tools.4. Remove all packaging material, make sure all parts are presentbefore assembly.5. Estimated Assembly Time: 30 minutes. Exact assembly timeswill vary based on skill level and past assembly experience.

Customer ServiceFor the missing or replacement of wooden panels, hardware, orelectric fireplace insert, please contact Vendor Customer Service at1-888-878-8820Working hour: Mon.-Fri., 8:30am - 5:30pm Pacific Standard Time.

CARE INSTRUCTIONS:1. Clean periodically by wiping the product with a soft clean cloth.2. Do not expose your product to any liquids. All liquids should bewiped up immediately with a soft, slightly damp cloth in thedirection of wood grain.3. Do not expose your product to strong or direct sunlight, near heatoutlets or air conditioning units, open windows or dampness.Excessive exposure to sunlight and heat can cause fading of yourfurniture finish. Extreme temperatures and humidity changes cancause wood cracking and splitting.4. Clean using a glass/mirror cleaner and soft cloth. Do not usecleaning products containing abrasives, as these will scratchglass/mirror.

!A

C

PARTS LIST

TOP 1pc

F

D

BASE 1pc

B

G H

I

FRONT PANEL 1pc TOP RAIL 1pc

LEFT SIDE PANEL

1pc

E

J K L

LEFT SIDE RAIL

1pc

RIGHT SIDE RAIL

1pc

LEFT SUPPORT

1pcs

RIGHT SUPPORT

1pcs

RIGHT SIDE PANEL

1pc

LEFT POST

1pc

RIGHT POST

1pc

ASSEMBLY INSTRUCTION

ELECTRIC FIREPLACE

INSERT 1pc

H1

H2

H3

H4

60 pcs

1 pcALLEN WRENCH

FLAT WASHER

4 MM

∅1/4"*16MM

SPRING WASHER ∅1/4"60 pcs

H5

6 pcs ROUND HEAD SCREW #8*12MM

PARTS LIST

SHORT BOLT ∅1/4*5/8" 32 pcs

H6

M Step 1Place Left side panel (E) face down on a smooth soft surface. (The sidewith the most holes should be facing up.) Align the holes of Bracket(H7) with the holes of Left side panel (E) with the tenons facing outwardas shown in figure 1. Secure the Bracket (H7) to the Left side panel (E)with Flat washer (H4), Spring washer (H3), and Short bolt (H2) usingAllen wrench (H5). DO NOT fully tighten bolts in this step for lateradjustment. Repeat this procedure to attach Bracket (H7) to Right sidepanel (F) and Front panel (C) as shown in figure 1.

Figure 1

LONG BOLT ∅1/4*1-1/4" 28 pcs

16 pcs

BRACKETH7

E

Tenons facing outside.

H2

H3

H4

H5

H7

E

C

H7

H7

N O

SIDE TRIM 2pcs POST TRIM

2pcs

ASSEMBLY INSTRUCTIONASSEMBLY INSTRUCTION ASSEMBLY INSTRUCTION

Figure 3

Step 2Place Left post (G) on a soft smooth surface. With assistance fromanother adult, slide Left side panel (E) into the groove of Left post (G)until both ends are flush. Secure the Left side panel (E) to Left post (G)with Short bolt (H2), Spring washer (H3), Flat washer (H4) using Allenwrench (H5) as shown in figure 2. DO NOT fully tighten the bolts in thisstep for later adjustment. Repeat this procedure to attach Right sidepanel (F) to Right post (H) as shown in figure 2.

Figure 2

E

G

F

H

H2

H3 H4

H5

G

E

B

E

F

G

H

H5

H2

H3

H4

Step 3With assistance from another adult, insert the tenons of Left side panel (E) and Rightside panel (F) into the corresponding holes of Base (B). Panels may need to be slightlyadjusted to be inserted into the proper holes. Secure Left side panel(E) and Right sidepanel (F) to Base (B) with Short bolt (H2), Spring washer (H3) and Flat washer (H4)using Allen wrench (H5). DO NOT fully tighten bolts in this step for later adjustment.Then secure Left post (G) and Right post (H) to Base (B) with Long bolt (H1), Springwasher (H3) and Flat washer (H4) using Allen wrench (H5). DO NOT fully tighten boltsin this step for later adjustment. As shown in figure 3.NOTE: The Left side panel (E) should be supported until secured in place to prevent thepanels from tipping and causing damage or injury.

B

E

H5

H1

H3

H4

ASSEMBLY INSTRUCTIONASSEMBLY INSTRUCTION ASSEMBLY INSTRUCTION

Figure 4 Figure 5

Step 4With assistance from another adult, place Side trim (M), Post trim (N)into the corresponding holes of Left side panel (E), Right side panel (F),Left post (G) and Right post (H). Side trim (M) should align with Leftpost (G) and Right post (H). Secure the trim in place with Long bolt (H1),Spring washer (H3), Flat washer (H4) using Allen wrench (H5) as shownin figure 4. DO NOT fully tighten bolts in this step for later adjustment.

H1

H3

H4

H5

E

F

M

M

Step 5Align the holes of Left support (K) and Left post (G). Secure Leftsupport (K) to Left post (G) with Long bolt (H1), Spring washer (H3)and Flat washer (H4) using Allen wrench (H5). DO NOT fully tightenbolts in this step for later adjustment. Repeat this process to attachRight Support (L) to Right post (H) as shown in figure 5.

H

G

B

H5

H1

H3

H4

N

N

H5

H1

H3

H4

B

K

L

G

H

G

K

ASSEMBLY INSTRUCTION ASSEMBLY INSTRUCTION

Step 6With assistance from another adult, place the Front panel (C) onto thetenons of Left support and Right support (K&L). Secure the Front panel(C) to Left post (G) and Right post (H) with Long bolt (H1), Springwasher (H3) and Flat washer (H4) using Allen wrench (H5) as shownin figure 6. DO NOT fully tighten bolts at this time for later adjustment.

Figure 6 Figure 7

C

K

L

G

H

B

K

L

B

C

H

G

H5

H1

H3

H4

C

G

D

I

J

C

C

D

I

J

H5

H1

H3

H4

D

C

I

Step 7With assistance from other adults, make sure the arrow label of the Left siderail(I) and Right side rail(J) point upward, insert the tenons of the Left siderail(I) and Right side rail(J) into the corresponding holes of Base(B) and hold.Then, insert the tenons of the Left side rail(I) and Right side rail(J) into thecorresponding holes of Top rail(D) (If there is difficulty, please slightly moveLeft side rail(I) and Right side rail(J) outward). Then align the holes and attachLeft side rail(I), Right side rail(J) and Top rail(D) with Long bolt(H1), Springwasher(H3) and Flat washer(H4) using Allen wrench(H5). Do not fully tightenbolts in this step for later adjustment. As shown figure 7.

Make sure the arrowlabel point upward.

D

I

ASSEMBLY INSTRUCTION ASSEMBLY INSTRUCTION

Step 8With assistance from another adult, align the tenons of Left side panel(E), Left post (G), Front panel (C), Right post (H) and Right side panel(F) with the corresponding holes in Top (A) as shown in figure 9. Takecare not to pinch your fingers as the top is lowered in place. Secure Top(A) to the Left side panel (E), Front panel (C) and Right side panel (F)with Short bolt (H2), Spring washer (H3) and Flat washer (H4) usingAllen wrench (H5). Adjust all parts to minimize any gaps betweenpanels and Fully tighten all bolts from Steps 1-8.

Figure 9Figure 8

Not provided

O

H6

J

I

O

J

Step 9Place the Electric fireplace insert (O) into the assembled Mantel fromthe back. Slide the Electric fireplace insert (O) into the opening of theassembled Mantel and center so the space around the insert and rails isequal. Secure the Electric fireplace insert to the back of the assembledMantel with Round head screws (H6) using Phillips screwdriver (notprovided) as shown in figure 9.

H5

H2

H3

H4

A

A

C

C

E

F

H

G

G

E

Assembly is now complete.Note: Please read the operating manual for the Electric Fireplace Insert andElectric Fireplace Insert remote control before using Fireplace.

MADE IN CHINA

ASSEMBLY INSTRUCTION

PRINTED IN CHINA

FP-1833-7說明书---螺杆统一-01图纸和视图模型

FP-1833-7說明书---螺杆统一-02图纸和视图模型

FP-1833-7說明书---螺杆统一-03图纸和视图模型

FP-1833-7說明书---螺杆统一-04图纸和视图模型

FP-1833-7說明书---螺杆统一-05图纸和视图模型

FP-1833-7說明书---螺杆统一-06图纸和视图模型

FP-1833-7說明书---螺杆统一-07图纸和视图模型

FP-1833-7說明书---螺杆统一-08图纸和视图模型