AG28 11’OC Cantilever

Assembly and Operation Guide

www.treasuregarden.com

©2018 Treasure Garden, Inc. - All Rights Reserved. Rev. 9/18

WARRANTY:

Treasure Garden warrants this product (in residential use) to be free from defectsin original materials and workmanship for aperiod of 1 year from the date of purchase.If a defect in the original material orworkmanship appears during the warrantyperiod; Treasure Garden will (at its option)repair or replace the product withoutcharge. Limited warranty against fabricfading, depending on fabric grade.

Simply contact your original authorizedTreasure Garden dealer with a descriptionof the defect. The dealer will verify thedefect and work closely with TreasureGarden to obtain the necessary service. In many cases, simple problems can besolved with a replacement part that can beshipped directly to the dealer forprofessional installation/repair.

In the event that warranted factory serviceis required, Treasure Garden will assumethe responsibility of the return freightcharges on warranted product for the firstyear only.

Returned product that (upon receipt andinspection) is deemed to be “not covered”under our warranty, will be shipped/billedat your expense.

This warranty gives you specific legal rights,and you may have other rights which varyfrom state to state.

NOTE: Failure caused by unreasonable orabusive use, or failure caused by neglect ofreasonable and necessary care are notcovered by this warranty.

Additionally, acts of nature (including but notlimited to wind, hurricanes, tornadoes, andstorms) are not covered by this warranty.

101

Prior to assembly it is important to decide on the location of the AG28 umbrella. The umbrella measures approximately 123” in height when opened.

• Allow ample height to avoid damage to your umbrella during assembly and usage.

• Choose a location that is level and sturdy.

• Avoid any sloping or soft ground cover.

• Consider a location that will maximize the umbrella’s rotating feature. Placing the AG28between two entertaining areas is ideal.

Thank you for purchasing Treasure Garden’s AG28 Cantilever Umbrella.

Please remove all contents from the package, inspect and review checklist. CAUTION: To reduce personal injury and damage to your AG28, read and follow thisassembly and operation guide We recommend a two-person team for assembly anddisassembly. Save information for future reference.

29

Collar (1)

Clamp (1)

Stem (1)

Bolts (2)

Hexagon Wrench (1)

Steel Wrench (1)

Protective Cover (1)Base Shell Base Lid

A

C

B

IE

G

F

J

P

H

M

K

N

L

O

D

Q

R

Spring Loaded Rib End Cap (8)

A - Base Shell and Base Lid J - Double Wind Vent CanopyB - Collar Base Stem K - Removable Crank HandleC - Main Frame L - Socket A - To open and extend armD - Housing M - Socket B - To open canopyE - Outer Frame Arm N - Crank Handle StorageF - Arm Connector O - Light AdapterG - Inner Frame Arm P - Spring Loaded Rib End CapH - Bottom Pole Q - Locking Rotation KnobI - Gemel Hinge R - Valance (optional)

REQUIRED FOR ASSEMBLY:• 200 lbs. of playground sand or all purpose sand (not included).

NOTE: Avoid allowing sand into the center of the base shell.

S A F E T Y P R E C A U T I O N S :• Close the umbrella in windy conditions or when a storm approaches. Never allow the umbrella to flap in the wind; this could damage the canopy.

• Do not leave open umbrella unattended. If damage occurs, this is not covered by the warranty.

• When adjusting the umbrella, make sure that no person(s) or item(s) are close to theumbrella. This is important to prevent injury or material damage.

C A R E A N D M A I N T E N A N C E :• When not in use, close and cover umbrella with a protective cover (included). • Allow a wet canopy to dry in open position.• If necessary, clean the fabric with lukewarm water, mild detergent, and a sponge.• Wipe sliding marks on the aluminum poles with a damp cloth.Winter Storage:• Store in a dry, protected place.After the Winter:• Areas subject to turning and sliding can be treated with a non-staining lubricant spray(silicone-based).

• Check the condition and function of the umbrella. Any defects must be repaired by aprofessional.

CAUTION: Fully assembled, the AG28 umbrella weighs over 300 lbs. Moving theumbrella fully assembled will increase the risk of damage to your umbrella and cancause serious injury. We recommend a two-person team to assemble or disassemblethe umbrella.

AG28 CHECKLIST

S T E P 1 Assemble AG28 BaseSelect area to set base and place in desired location.Remove base lid from base shell and set aside (Fig. 1). Insert the base stem into the baseshell (Fig. 2). Turn collar base stem in a clockwise motion to engage threading. Fillbase shell with dry playground or all-purpose sand (not included) (Fig. 3). NOTE: Baseweight will be 250 lbs. after sand is added. Remove the base stem carefully and avoidallowing sand into the center of the base shell (Fig. 4). IMPORTANT: Do not allow sand to spillinto the center of the base (Fig. 4) as it will interfere with collar base stem installation. Place baselid back onto base shell.

83

CAUTION: Fully assembled, the AG28 umbrella weighs over 300 lbs. Moving theumbrella fully assembled will increase the risk of damage to your umbrella and cancause serious injury. We recommend a two-person team to assemble the umbrella.

(Fig. 1)

(Fig. 3)

Avoid allowing sandinto the center of thebase shell.

!

(Fig. 2)

(Fig. 4)

(Fig. 18) (Fig. 19)

AG28 Features

To Attach an Umbrella Light:Loosen the light adapter built into the umbrella runner by turning counter-clockwise

(Fig. 18). After loosening, pull down light adapter post (Fig. 19) to attach theumbrella light (sold separately).

To Remove Umbrella Light and Close Adapter:Remove umbrella light, and gently push up the light adapter post back into umbrella runnerand tighten turning clockwise (Fig. 18).

47

Stem SteelWrench

Clamp

Collar

(Fig. 7)

(Fig. 5) (Fig. 6)

(Fig. 8)

(Fig. 16)

(Fig. 17)

S T E P 2 Assemble AG28 Collar Base StemRe-insert the base stem into the base shell. Turn collar base stem in a clockwisemotion to engage threading (Fig. 5). Insert steel wrench provided into holes on top ofstem and tighten (Fig. 6). NOTE: To avoid damage to your base, do not over-tighten basestem. Insert clamp into base stem (Fig. 7). Attach collar to top of the base stem byengaging threading (Fig. 8). Do not completely tighten before inserting AG28 umbrellaframe.

S T E P 5 Rotating AG28Pull out the locking rotation knob to disengage lock (Fig. 16) and place second hand onSocket B crank system simultaneously to rotate in either direction (Fig. 17). After desiredlocation is reached, release rotation knob to lock into one of the 12 preset locking positions.

S T E P 3 Assemble AG28 FrameTo prevent scratching frame during assembly, lay umbrella parts on soft surface.Remove packaging from umbrella. NOTE: Keep canopy structure and frame arm strapped.

Attach the bottom pole into the housing, bottom pole only fits one way. Line up holes andsecure the two bolts with hexagon wren ch (Fig. 9). Insert crank handle into socket A ofhousing (Fig. 10). Crank inner frame arm counter-clockwise until arm stops. To preparebase for umbrella, release collar base stem by turning the collar counter-clockwise(Fig. 11). Lift and insert umbrella frame into collar base stem (Two Persons Required).Secure position by tightening the collar in a clockwise direction (Fig. 12).NOTE: Cantilever will open counter-clockwise but not designed to be operated in thatmatter.

65

(Fig. 10)(Fig. 9)

(Fig. 11)

(Fig. 12)

Socket A

(Fig.13) (Fig.14)

(Fig.15)

SSoSocSockSockeSocketSocket Socket ASocket A SSoSocSockSockeSocketSocket Socket BSocket BSSocket BSoSocket BSocSocket BSockSocket BSockeSocket BSocketSocket BSocket Socket BSocket BSocket B

SSoSocSockSockeSocketSocket Socket ASocket A

To Adjust Vertical Shade:Insert crank handle into socket A (Fig. 15) and slowly crank counter-clockwise to desired degree ofvertical shade.

S T E P 4 Opening and ClosingTo Open and Extend Arm:Insert crank handle fully into socket A (Fig. 13), crank handle will snap into place, thenslowly crank the handle clockwise until crank handle stops and arm is fullyextended outward. CAUTION: Arm must be fully extended before retracting. Do not overcrank, as it will damage your umbrella.

To Open Canopy:Insert crank handle fully into socket B (Fig. 14), crank handle will snap into place, thenslowly crank the handle clockwise until canopy is completely open and hub isinserted under center pole and crank handle stops.

To Close Canopy:Set canopy to horizontal position and turn crank handle socket B counter-clockwise.

Stopper

S T E P 3 Assemble AG28 FrameTo prevent scratching frame during assembly, lay umbrella parts on soft surface.Remove packaging from umbrella. NOTE: Keep canopy structure and frame arm strapped.

Attach the bottom pole into the housing, bottom pole only fits one way. Line up holes andsecure the two bolts with hexagon wren ch (Fig. 9). Insert crank handle into socket A ofhousing (Fig. 10). Crank inner frame arm counter-clockwise until arm stops. To preparebase for umbrella, release collar base stem by turning the collar counter-clockwise(Fig. 11). Lift and insert umbrella frame into collar base stem (Two Persons Required).Secure position by tightening the collar in a clockwise direction (Fig. 12).NOTE: Cantilever will open counter-clockwise but not designed to be operated in thatmatter.

65

(Fig. 10)(Fig. 9)

(Fig. 11)

(Fig. 12)

Socket A

(Fig.13) (Fig.14)

(Fig.15)

SSoSocSockSockeSocketSocket Socket ASocket A SSoSocSockSockeSocketSocket Socket BSocket BSSocket BSoSocket BSocSocket BSockSocket BSockeSocket BSocketSocket BSocket Socket BSocket BSocket B

SSoSocSockSockeSocketSocket Socket ASocket A

To Adjust Vertical Shade:Insert crank handle into socket A (Fig. 15) and slowly crank counter-clockwise to desired degree ofvertical shade.

S T E P 4 Opening and ClosingTo Open and Extend Arm:Insert crank handle fully into socket A (Fig. 13), crank handle will snap into place, thenslowly crank the handle clockwise until crank handle stops and arm is fullyextended outward. CAUTION: Arm must be fully extended before retracting. Do not overcrank, as it will damage your umbrella.

To Open Canopy:Insert crank handle fully into socket B (Fig. 14), crank handle will snap into place, thenslowly crank the handle clockwise until canopy is completely open and hub isinserted under center pole and crank handle stops.

To Close Canopy:Set canopy to horizontal position and turn crank handle socket B counter-clockwise.

Stopper

47

Stem SteelWrench

Clamp

Collar

(Fig. 7)

(Fig. 5) (Fig. 6)

(Fig. 8)

(Fig. 16)

(Fig. 17)

S T E P 2 Assemble AG28 Collar Base StemRe-insert the base stem into the base shell. Turn collar base stem in a clockwisemotion to engage threading (Fig. 5). Insert steel wrench provided into holes on top ofstem and tighten (Fig. 6). NOTE: To avoid damage to your base, do not over-tighten basestem. Insert clamp into base stem (Fig. 7). Attach collar to top of the base stem byengaging threading (Fig. 8). Do not completely tighten before inserting AG28 umbrellaframe.

S T E P 5 Rotating AG28Pull out the locking rotation knob to disengage lock (Fig. 16) and place second hand onSocket B crank system simultaneously to rotate in either direction (Fig. 17). After desiredlocation is reached, release rotation knob to lock into one of the 12 preset locking positions.

S T E P 1 Assemble AG28 BaseSelect area to set base and place in desired location.Remove base lid from base shell and set aside (Fig. 1). Insert the base stem into the baseshell (Fig. 2). Turn collar base stem in a clockwise motion to engage threading. Fillbase shell with dry playground or all-purpose sand (not included) (Fig. 3). NOTE: Baseweight will be 250 lbs. after sand is added. Remove the base stem carefully and avoidallowing sand into the center of the base shell (Fig. 4). IMPORTANT: Do not allow sand to spillinto the center of the base (Fig. 4) as it will interfere with collar base stem installation. Place baselid back onto base shell.

83

CAUTION: Fully assembled, the AG28 umbrella weighs over 300 lbs. Moving theumbrella fully assembled will increase the risk of damage to your umbrella and cancause serious injury. We recommend a two-person team to assemble the umbrella.

(Fig. 1)

(Fig. 3)

Avoid allowing sandinto the center of thebase shell.

!

(Fig. 2)

(Fig. 4)

(Fig. 18) (Fig. 19)

AG28 Features

To Attach an Umbrella Light:Loosen the light adapter built into the umbrella runner by turning counter-clockwise

(Fig. 18). After loosening, pull down light adapter post (Fig. 19) to attach theumbrella light (sold separately).

To Remove Umbrella Light and Close Adapter:Remove umbrella light, and gently push up the light adapter post back into umbrella runnerand tighten turning clockwise (Fig. 18).

29

Collar (1)

Clamp (1)

Stem (1)

Bolts (2)

Hexagon Wrench (1)

Steel Wrench (1)

Protective Cover (1)Base Shell Base Lid

A

C

B

IE

G

F

J

P

H

M

K

N

L

O

D

Q

R

Spring Loaded Rib End Cap (8)

A - Base Shell and Base Lid J - Double Wind Vent CanopyB - Collar Base Stem K - Removable Crank HandleC - Main Frame L - Socket A - To open and extend armD - Housing M - Socket B - To open canopyE - Outer Frame Arm N - Crank Handle StorageF - Arm Connector O - Light AdapterG - Inner Frame Arm P - Spring Loaded Rib End CapH - Bottom Pole Q - Locking Rotation KnobI - Gemel Hinge R - Valance (optional)

REQUIRED FOR ASSEMBLY:• 200 lbs. of playground sand or all purpose sand (not included).

NOTE: Avoid allowing sand into the center of the base shell.

S A F E T Y P R E C A U T I O N S :• Close the umbrella in windy conditions or when a storm approaches. Never allow the umbrella to flap in the wind; this could damage the canopy.

• Do not leave open umbrella unattended. If damage occurs, this is not covered by the warranty.

• When adjusting the umbrella, make sure that no person(s) or item(s) are close to theumbrella. This is important to prevent injury or material damage.

C A R E A N D M A I N T E N A N C E :• When not in use, close and cover umbrella with a protective cover (included). • Allow a wet canopy to dry in open position.• If necessary, clean the fabric with lukewarm water, mild detergent, and a sponge.• Wipe sliding marks on the aluminum poles with a damp cloth.Winter Storage:• Store in a dry, protected place.After the Winter:• Areas subject to turning and sliding can be treated with a non-staining lubricant spray(silicone-based).

• Check the condition and function of the umbrella. Any defects must be repaired by aprofessional.

CAUTION: Fully assembled, the AG28 umbrella weighs over 300 lbs. Moving theumbrella fully assembled will increase the risk of damage to your umbrella and cancause serious injury. We recommend a two-person team to assemble or disassemblethe umbrella.

AG28 CHECKLIST

WARRANTY:

Treasure Garden warrants this product (in residential use) to be free from defectsin original materials and workmanship for aperiod of 1 year from the date of purchase.If a defect in the original material orworkmanship appears during the warrantyperiod; Treasure Garden will (at its option)repair or replace the product withoutcharge. Limited warranty against fabricfading, depending on fabric grade.

Simply contact your original authorizedTreasure Garden dealer with a descriptionof the defect. The dealer will verify thedefect and work closely with TreasureGarden to obtain the necessary service. In many cases, simple problems can besolved with a replacement part that can beshipped directly to the dealer forprofessional installation/repair.

In the event that warranted factory serviceis required, Treasure Garden will assumethe responsibility of the return freightcharges on warranted product for the firstyear only.

Returned product that (upon receipt andinspection) is deemed to be “not covered”under our warranty, will be shipped/billedat your expense.

This warranty gives you specific legal rights,and you may have other rights which varyfrom state to state.

NOTE: Failure caused by unreasonable orabusive use, or failure caused by neglect ofreasonable and necessary care are notcovered by this warranty.

Additionally, acts of nature (including but notlimited to wind, hurricanes, tornadoes, andstorms) are not covered by this warranty.

101

Prior to assembly it is important to decide on the location of the AG28 umbrella. The umbrella measures approximately 123” in height when opened.

• Allow ample height to avoid damage to your umbrella during assembly and usage.

• Choose a location that is level and sturdy.

• Avoid any sloping or soft ground cover.

• Consider a location that will maximize the umbrella’s rotating feature. Placing the AG28between two entertaining areas is ideal.

Thank you for purchasing Treasure Garden’s AG28 Cantilever Umbrella.

Please remove all contents from the package, inspect and review checklist. CAUTION: To reduce personal injury and damage to your AG28, read and follow thisassembly and operation guide We recommend a two-person team for assembly anddisassembly. Save information for future reference.

AG28 11’OC Cantilever

Assembly and Operation Guide

www.treasuregarden.com

©2018 Treasure Garden, Inc. - All Rights Reserved. Rev. 9/18