Artisan Technology Group is your source for quality ......10-28VDC, 0.5 Amp Sourcing Digital Output...
Transcript of Artisan Technology Group is your source for quality ......10-28VDC, 0.5 Amp Sourcing Digital Output...
-
(217) 352-9330 | [email protected] | artisantg.com
-~ ARTISAN® ~I TECHNOLOGY GROUP Your definitive source for quality pre-owned equipment.
Artisan Technology Group
Full-service, independent repair center with experienced engineers and technicians on staff.
We buy your excess, underutilized, and idle equipment along with credit for buybacks and trade-ins.
Custom engineering so your equipment works exactly as you specify.
• Critical and expedited services • Leasing / Rentals/ Demos
• In stock/ Ready-to-ship • !TAR-certified secure asset solutions
Expert team I Trust guarantee I 100% satisfaction All trademarks, brand names, and brands appearing herein are the property of their respective owners.
Find the GE Fanuc IC300OCS200G at our website: Click HERE
tel:2173529330mailto:[email protected]://artisantg.comhttps://www.artisantg.com/TestMeasurement/76769-1/GE-Fanuc-IC300OCS200G-Operator-Control-Stationhttps://www.artisantg.com/TestMeasurement/76769-1/GE-Fanuc-IC300OCS200G-Operator-Control-Station
-
Supplement forSmartStack Modules
SmartStack Modules
November 10, 1999 GFK-1601A
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
GFK-1601A 10 NOV 1999 PAGE 3
Warnings, Cautions, and Notesas Used in this Publication
Warning noti ces are used in this publication to emphasize thathazardous voltages, currents, temperatures or other conditions thatcould cause personal injury exist in this equipment or may beassociated with its use.
In situations where inattention could cause either personal injuryor damage to equipment, a Warning notice is used.
Caution notices are used where equipment might be damaged if care isnot taken.
Note
Notes merely call attention to information that is especially significant tounderstanding and operating the equipment.
This document is based on information available at the time of its publication. Whileefforts have been made to be accurate, the information contained herein does notpurport to cover all details or variations in hardware or software, nor to provide forevery possible contingency in connection with installation, operation, or maintenance.Features may be described herein which are not present in all hardware and softwaresystems. GE Fanuc Automation assumes no obligation of notice to holders of this documentwith respect to changes subsequently made.
GE Fanuc Automation makes no representations or warranty, expressed, implied, orstatutory with respect to, and assumes no responsibility for the accuracy, completeness,sufficiency, or usefulness of the information contained herein. No warranties ofmerchantability or fitness for purpose shall apply.
The following are trademarks of GE Fanuc Automation North America, Inc.
Alarm Master CIMSTAR Helpmate PROMACRO Series SixCIMPLICITY GEnet Logicmaster Series One Series 90CIMPLICITY 90 – ADS Genius ModelMaster Series Three VuMasterCIMPLICITY Power TRAC Genius PowerTRAC ProLoop Series Five Workmaster
The following are trademarks of Horner APG, LLC.
Cscape SmartStack CsCAN
Copyright 1999 GE Fanuc Automation North America, Inc.All Rights Reserved
Warning
Caution
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
PAGE 4 10 NOV 1999 GFK-1601A
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
GFK-1601A 10 NOV 1999 PAGE 5
Revisions to This Manual
This version (GFK-1601A) of the SmartStack Modules Supplement contains the following revisionsand additions:
1. Added three SmartStack Module Data Modules: IC300DIQ712; IC300DIQ722;and IC300ADC920.
2. Revised the Configuration section in the following SmartStack Data Sheets by adding a Module Setup tab. The Module Setup tab is used in applications where it is necessary to change the default output states (for digital modules) or default output values (for analog modules.) when the controller enters the idle/stop mode.
Also added a Warning Statement in the Configuration section indicating that extreme caution must be exercised when changing the default settings using the Module Setup tab.
IC300DQM202 IC300ADC920IC300DIQ511/611 IC300DAC001/101IC300DIQ711 IC300DAC002/102IC300DIQ512/612 IC300MIX011/111IC300DIQ712 IC300MIX022/122IC300DIQ522/622 IC300MIX901IC300DIQ524/624 IC300MIX902IC300DIQ935
3. Made changes to the following SmartStack Modules as indicated:
IC300DIQ511IC300DIQ611
Specification Table:Revised Output Protection.
IC300DIQ711 Section 2.2, Output Wiring:Revised OCS graphic to depict the bottom view instead of the top view.Revised Output pin-out table to match the pins with the correspondingoutputs.
IC300DIQ512IC300DIQ612
Specification Table:Revised Input and Output Commons per Module.Renamed Output Operating Voltage to Coil Voltage and changedparameter value.Renamed Peak Voltage to Contact Voltage and changed parametervalue.Revised ON Voltage drop parameter.
IC300DIQ712 NewIC300DIQ522
IC300DIQ622
Specification Table:Renamed Operating Voltage to Coil Voltage and changed parametervalue.Revised Wiring drawing by removing + and – signs on outputs.Renamed Peak Voltage to Contact Voltage. No change in parameter.
IC300DIQ722 NewIC300DIQ524IC300DIQ624
Specification Table:Revised Input and Output Commons per Module.Revised Input Impedance (Revised parameter from “=10K” to “+10K.”)Relabeled Output parameter “Peak Voltage” as “Contact Voltage.”
IC300ADC020IC300ADC120
Section 2, Wiring DrawingRevised label on third set of inputs from “T4-20mA” to “4-20mA.”
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
PAGE 6 10 NOV 1999 GFK-1601A
IC300ADC920 NewIC300THM000IC300THM100
Specification Table:Added note regarding accuracy specifications.
IC300MIX022IC300MIX122
Revised Section 5.1, Example, Item 2:Changed “+20VDC” to “+20mA.”
IC300MIX901 Specification Table:Deleted Analog Input Usable Resolution.Deleted Analog Output Voltage Output Resolution.Section 2.1, Digital Input/Output (P1) Wiring DrawingRevised labeling in terminal block –renamed “C” to “C1.”Revised Digital Input/Output table (P1) – renamed “C” to “C1.”Section 2.2, Analog Input/Output (P2) Wiring DrawingRevised labeling in terminal block – renamed “C” to “C2” and “C3.”Revised Analog In and Out Pin-out table (P2) – renamed “C” to “C2” and“C3.”
IC300MIX902 Specification Table:Revised Analog Input Input Impedance (Revised “200 Ohm >” to“200 Ohms
-
GFK-1601A 10 NOV 1999 PAGE 7
TABLE OF CONTENTS
Chapter 1: Introduction……………………………………………………………………………….. 91.1 Scope………………………………………………………………………………………………… 9 IC300DIM210…………………………………………………………………………………………… 13 IC300DQM202…………………………………………………………………………………….……. 15 IC300DIQ511/611..……………………………………………………………………………….……. 19 IC300DIQ711……..…………………………………………………………………………………….. 23 IC300DIQ512/612………………………………………………………………………….…..………. 29 IC300DIQ712……..…………………………………………………………………………………….. 33 IC300DIQ516/616..……………………………………………………………………….……………. 39 IC300DIQ716…………………………………………………………………………………...………. 43 IC300DIQ522/622..………………………………………………………………………….…………. 49 IC300DIQ722……..………………………………………………………………………….…………. 53 IC300DIQ524/624…………………………………………………………………………………..….. 59 IC300DIQ935……..………………………………………………………………………………….…. 63 IC300ADC010/110……………………………………………………………….………………….…. 69 IC300ADC020/120..……………………………………………………………………………………. 73 IC300ADC920…….……………………………………………………………………………….……. 77 IC300RTD000/100..……………………………………………………………………………………. 83 IC300THM000/100…..…………………………………………………………………………………. 87 IC300DAC001/101…..…………………………………………………………………………………. 91 IC300DAC002/102…..…………………………………………………………………………………. 95 IC300MIX011/111……………………………………………………………………………………… 99 IC300MIX022/122……………………………………………………………………………………… 105 IC300MIX901…………………………………………………………………………………………… 111 IC300MIX902…………………………………………………………………………………………… 119 IC300ASC100………………………………………………………………………………………….. 125 IC300HSC600….………………………………………………………………………………………. 129 IC300HSC601….………………………………………………………………………………………. 133 IC300STP100.…….……………………………………………………………………………………. 137
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
PAGE 8 10 NOV 1999 GFK-1601A
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
GFK-1601A 10 NOV 1999 PAGE 9
CHAPTER 1: INTRODUCTION
1.1 Scope
This supplement contains data sheets for the SmartStack I/O Option Modules. Wiring diagrams,specifications, and other pertinent information are provided. Installation and configuration proceduresthat are common to all SmartStack Modules are covered in the Control Station Hardware Manual (GFK-1631). Table 1.1 contains a list of SmartStack Modules that are currently available.
Table 1.1 - SMARTSTACK MODULESDIGITAL INPUT MODULES12/24VDC Input Positive/Negative Logic IC300DIM210DIGITAL OUTPUT MODULESRelay Output 4A Maximum IC300DQM202DIGITAL INPUT AND OUTPUT COMBINATION MODULES
4 Channel, 12/24VDC (Isolated) Digital In, Positive/Negative Logic,4 Channel, 24VDC Out, Negative Logic
IC300DIQ511Mixed DC I/O
8 Channel, 12/24VDC (Isolated) Digital In, Positive/Negative Logic,8 Channel, 24VDC Out, Negative Logic
IC300DIQ611
Mixed DC I/O 16 Channel, 12/24 VDC In,Positive/Negative Logic12 Channel, 24 VDC Out, Negative Logic
IC300DIQ711
4 Channel, 12/24VDC, (Isolated) Digital In, Positive/Negative Logic4 Channel, 10-28VDC (Sourcing) Out, Positive Logic
IC300DIQ516Mixed DC I/O
8 Channel, 12/24VDC In, (Isolated) Digital In, Positive/Negative Logic8 Channel, 10-28VDC (Sourcing) Out, Positive Logic
IC300DIQ616
Mixed DC I/O 16 Channel, 12/24VDC In (Isolated) Digital In, Positive/Negative Logic12 Channel, 10-28VDC (Sourcing) Out, Positive Logic
IC300DIQ716
4 Channel, 12/24VDC (Isolated) Digital In, Positive/Negative Logic,3 Channel, 3A Relay Out
IC300DIQ512Mixed I/O
8 Channel, 12/24VDC (Isolated) Digital In, Positive/Negative Logic,6 Channel, 3A Relay Out
IC300DIQ612
Mixed I/O 14 Channel, 12/24VDC (Isolated) Digital In, Positive/Negative Logic,10 Channel, 3A Relay Out
IC300DIQ712
Mixed I/O 4 Channel, 120 VAC InPositive Logic3 Channel, 3A Relay Out
IC300DIQ522
Mixed I/O 8 Channel, 120 VAC InPositive Logic6 Channel, 3A Relay Out
IC300DIQ622
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
PAGE 10 10 NOV 1999 GFK-1601A
Mixed I/O 14 Channel, 120 VAC InPositive Logic10 Channel, 3A Relay Out
IC300DIQ722
4 Channel, 120VAC In, Positive Logic4 Channel, 80-240VAC Out, Positive Logic
IC300DIQ524AC Input / AC Output
8 Channel, 120VAC In, Positive Logic8 Channel, 80-240VAC Out, Positive Logic
IC300DIQ624
High DensityMixed DC I/O
32 Channel, 12/24 VDC, Positive Logic40 Channel, 24Vdc Out, Negative Logic50mA Maximum, Non-Inductive
IC300DIQ935
ANALOG INPUT MODULES2 Channels, 12 Bit Resolution, +/-10VDC IC300ADC010+/-10VDC Analog Input4 Channels, 12 Bit Resolution, +/-10VDC IC300ADC1102 Channels, 12 Bit Resolution, 4-20mA IC300ADC0204-20mA Analog Input4 Channels, 12 Bit Resolution, 4-20mA IC300ADC120
Thermistor / Current/Voltage Analog Input
12 Channels, 12 Bit Resolution,4-20mA / 0-5VDC
IC300ADC920
2 Channels IC300RTD000RTD Input4 Channels IC300RTD1002 Channels IC300THM000Thermocouple Input4 Channels IC300THM100
ANALOG OUTPUT MODULES2 Channels, 14 Bit Resolution, +/-10VDC IC300DAC001+/-10VDC Analog Output4 Channels, 14 Bit Resolution, +/-10VDC IC300DAC101
2 Channels, 14 Bit Resolution, 4-20mA IC300DAC0024-20mA Analog Output4 Channels, 14 Bit Resolution, 4-20mA IC300DAC102
ANALOG INPUT AND OUTPUT COMBINATION MODULES1 Channel, 12 Bit Resolution, +/-10VDC In,1 Channel, 12 Bit Resolution, +/-10VDC Out
IC300MIX011+/-10VDC Analog I/O
2 Channel, 12 Bit Resolution, +/-10VDC In,2 Channel, 12 Bit Resolution, +/-10VDC Out
IC300MIX111
1 Channel, 12 Bit Resolution, 20mA In1 Channel, 12 Bit Resolution, 20mA Out
IC300MIX02220mA Analog I/O
2 Channel, 12 Bit Resolution, 20mA In,2 Channel, 12 Bit Resolution, 20mA Out
IC300MIX122
ANALOG / DIGITAL INPUT AND OUTPUT COMBINATION MODULES+/-10VDCAnalog / Digital I/O
4 Channel, Analog Input, +/-10VDC In2 Channel Analog Output, +/-10VDC Out8 Channel, 12 Bit Resolution, 24VDC Bipolar Digital Input8 Channel, 12 Bit Resolution, 10-28VDC, 0.5 Amp Sourcing Digital Output
IC300MIX901
4-20mAAnalog / Digital I/O
4 Channel, Analog Input, 20mA In2 Channel Analog Output, 20mA Out8 Channel, 12 Bit Resolution, 24VDC Bipolar Digital Input8 Channel, 12 Bit Resolution, 10-28VDC, 0.5 Amp Sourcing Digital Output
IC300MIX902
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
GFK-1601A 10 NOV 1999 PAG E 11
SPECIALTY MODULESASCII BASIC
Product also has a detailedSupplement (GFK-1666) whichis ordered separately.
3 High Speed Communication Ports IC300ASC100
High Speed Counter Inputs,Sinking Pulse Outputs
IC300HSC600High Speed Counter
Product also has a detailedSupplement (GFK-1643) whichis ordered separately. CoversHSC600 and HSC601.
High Speed Counter Inputs,Sourcing Pulse Outputs
IC300HSC601
Stepper Positioning
Product also has a detailedSupplement (GFK-1644) whichis ordered separately.
Stepper Inputs / Stepper Outputs IC300STP100
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
PAGE 12 10 NOV 1999 GFK-1601A
NOTES
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
GFK-1601A 10 NOV 1999 PAGE 13
This Data Sheet (GFK-1603A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
1 SPECIFICATIONS
Inputs per Module 8 isolated Input Characteristics Differential andBiDirectional
Commons per Module 8 Maximum OFF Current 200µAInput Voltage Range 12-24VDC Base Power Required 30mAPeak Voltage 35VDC Max. OFF to ON Response 1ms.Isolation Voltage(Channel to Channeland Channel to Bus)
500VDC ON to OFF Response 1ms.
Required Power(Steady State)
0.92W (38.5mA@ 24VDC)
Terminal Type Spring Clamp, Removable
Required Power(Inrush)
Negligible Status Indicator 8 LEDs
ON Voltage Level 9VDC Min. Relative Humidity 5 to 95% Non-condensingOFF Voltage Level 3VDC Max. Operating Temperature 0° to 60° CelsiusInput Impedance . 10K Ohms CE PendingMinimum ON Current 1 mA.
Weight 9 oz. (256 g)UL Refer to GFK-1754
2 WIRING
GFK-1603A
12/24Vdc Input ModuleIC300DIM210
Positive/Negative Logic
Pin Signal1 Input 1 +/-1 Input 1 -/+2 Input 2 +/-2 Input 2 -/+3 Input 3 +/-3 Input 3 -/+4 Input 4 +/-4 Input 4 -/+5 Input 5 +/-5 Input 5 -/+6 Input 6 +/-6 Input 6 -/+7 Input 7 +/-7 Input 7 -/+8 Input 8 +/-8 Input 8 -/+
*
OCS Bottom View – Shows corresponding I/O pinl ti
+ -
+-1 2-2 4VDC
+ -
+-1 2-2 4VDC
+ -
+-1 2-2 4VDC
+ -
+-1 2-2 4VDC
+ -
+-1 2-2 4VDC
+ -
+-1 2-2 4VDC
+ -
+-1 2-2 4VDC
+ -
+-1 2-2 4VDC
3
5
6
4
5
7
1
1
3
2
2
4
6
7
8
8
D IM 2 10
*
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
PAGE 14 10 NOV 1999 GFK-1601A
This Data Sheet (GFK-1603A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
3 INTERNAL CIRCUIT SCHEMATIC
4 CONFIGURATION
Preliminary configuration procedures that are applicable to all SmartStack Modules are located in theControl Station Hardware Manual (GFK-1631). Although the module has no user defined parameters, theI/O Map describes which I/O registers are assigned to a specific SmartStack Module and where themodule is located in the point map. The I/O Map is determined by the model number and location withinthe SmartStack. The I/O Map is not edited by the user.
5 INSTALLATION / SAFETY
All applicable codes and standards are to be followed in the installation of this product.
For detailed installation information, refer to Chapter Two in the Control Station Hardware Manual(GFK-1631). A handy checklist is provided that covers panel box layout requirements and minimumclearances.
6 TECHNICAL ASSISTANCE
For user manual updates, contact GE Fanuc PLC Technical Services Hotline at 1-800-433-2682 or visitour website at www.gefanuc.com.
To Contro lle r
VCCI/O Connecto r
2
1
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
GFK-1601A 10 NOV 1999 PAGE 15
This Data Sheet (GFK-1605A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
1 SPECIFICATIONS
Outputs per Module 8 N.O. Relay Maximum Inrush Current 10ACommons per Module 1 OFF to ON Response 10ms Max.Output Points Consumed 8 ON to OFF Response 5ms. Max.Isolation (Channel to Channel) (Channel to Bus)
500VDC Terminal Type Spring Clamp, Removable
Operating Voltage 18-32VDC Relative Humidity 5 to 95% Non-condensingOutput Type NO Operating Temperature 0° to 60° CelsiusRequired Power(Steady State)
0.13W ( 5.5mA@ 24VDC)
CE Refer to GFK-1755
Required Power (Inrush) Negligible ULOperating TemperatureCode T4A; Also refer to
GFK-1754ON Voltage Level 0.15V Status Indicator 8 LEDs
Maximum Load Voltage 250 VAC,30VDC Max.
Weight 10.5 oz. (298 g)
Maximum Load Current(resistive)
4A Max.(Subject toDerating)
Maximum Leakage Current 5µA
Protection
Internal 10A non-replaceable fuse and
reverse polarityprotection
2 WIRING
GFK-1605A
Relay Output ModuleIC300DQM202
4 Amp Maximum
Pin SignalQ1 Output 1 N.O. ContactC1 Output 1 CommonQ2 Output 2 N.O. ContactC2 Output 2 CommonQ3 Output 3 N.O. ContactC3 Output 3 CommonQ4 Output 4 N.O. ContactC4 Output 4 CommonQ5 Output 5 N.O. ContactC5 Output 5 CommonQ6 Output 6 N.O. ContactC6 Output 6 CommonQ7 Output 7 N.O. ContactC7 Output 7 CommonQ8 Output 8 N.O. ContactC8 Output 8 CommonVC Relay Coil Voltage
CommonV+ Relay Coil Voltage +
5-30VDCOR
5-250VAC
LOAD
5-30VDCOR
5-250VAC
LOAD
5-30VDCOR
5-250VAC
LOAD
5-30VDCOR
5-250VAC
LOAD
5-30VDCOR
5-250VAC
LOAD
5-30VDCOR
5-250VAC
LOAD
5-30VDCOR
5-250VAC
LOAD
5-30VDCOR
5-250VAC
LOAD
+
-18-30VDC
C3
Q5
C6
Q4
C5
Q7
C1
Q1
Q3
Q2
C2
C4
Q6
C7
Q8
C8
VC
V+
DQM202
*
*
OCS Bottom View – Showscorresponding I/O pin
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
PAGE 16 10 NOV 1999 GFK-1601A
This Data Sheet (GFK-1605A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
3 INTERNAL CIRCUIT SCHEMATIC
4 CONFIGURATION
Preliminary configuration procedures that are applicable to all SmartStack Modules are located in theControl Station Hardware Manual (GFK-1631).
Selecting the I/O Map tab provides information about the I/O registers, which are assigned to a specificSmartStack Module and where the module is located in the point map. The I/O Map is determined bythe model number and location within the SmartStack. The I/O Map is not edited by the user.
The Module Setup is used in applications where it is necessary to change the default states of theoutputs when the controller (e.g., OCS100) enters idle/stop mode. The default turns the outputs OFFwhen the controller enters idle/stop mode. By selecting the Module Setup tab, each output can be set toeither turn ON, turn OFF or to hold the last state. Generally, most applications use the default settings.
5 INSTALLATION / SAFETY
All applicable codes and standards are to be followed in the installation of this product.
For detailed installation information, refer to Chapter Two in the Control Station Hardware Manual(GFK-1631). A handy checklist is provided that covers panel box layout requirements and minimumclearances.
+24V+
�
I/O ConnectorC1
Q1
Warning: The default turns the outputs OFF when the controller enters idle/stop mode. To avoidinjury of personnel or damages to equipment, exercise extreme caution when changing the defaultsetting using the Module Setup tab.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
GFK-1601A 10 NOV 1999 PAGE 17
This Data Sheet (GFK-1605A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
6 OUTPUT CHARACTERISTICS
Typical Relay Life
Voltage and Load Type Load Current 1 Amp 2 Amp 4 Amp30VDC Resistive 800K 500K 200K30VDC Inductive 500K 250K 100K250VAC Resistive 800K 500K 200K250VAC Inductive 500K 250K 100K
7 TECHNICAL ASSISTANCE
For user manual updates, contact GE Fanuc PLC Technical Services Hotline at 1-800-433-2682 or visitour website at www.gefanuc.com.
Derating Chart for DQM202
0 10 20 30 40 50 60 °C 32 50 68 86 104 122 140 °F
0
1
2
3
4
AMPS
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
PAGE 18 10 NOV 1999 GFK-1601A
This Data Sheet (GFK-1605A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
NOTES
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
GFK-1601A 10 NOV 1999 PAGE 19
This Data Sheet (GFK-1606A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
1 SPECIFICATIONS
INPUT DIQ511 DIQ611 DIQ511 DIQ611Inputs per Module 4 8 Input Characteristics BidirectionalCommons perModule
1 1 Input Impedance 10K Ohms
Input Voltage Range 12-24VDC Minimum ON Current 1mAPeak Voltage 35VDC Max. Maximum OFF Current 200µAIsolation(Channel to Bus)
500VDC OFF to ON Response 1ms.
ON Voltage Level 9VDC ON to OFF Response 1ms.OFF Voltage Level 3VDC Status Indicator 4 8
OUTPUT DIQ511 DIQ611 DIQ511 DIQ611Outputs per Module 4 8 Output Protection Short CircuitCommons perModule 1 1 Maximum Leakage Current 100µA
Operating Voltage 5 - 35VDC Maximum Inrush Current 600mA.Output Type Sinking / 10K Pull-Up Minimum Load NonePeak Voltage 35VDC Max. OFF to ON Response 1ms.OutputCharacteristics
Current Sinking ON to OFF Response 1ms.
ON Voltage Level 1.5VDC Max.Maximum LoadCurrent
0.5A Max.Status Indicator 8 LEDs
General SpecificationsRequired Power(Steady State)
0.18W (7.7mA @ 24VDC) CE Refer to GFK-1755
Required Power (Inrush) Negligible UL Refer to GFK-1754Relative Humidity 5 to 95% Non-condensing Terminal Type Spring Clamp, RemovableOperating Temperature 0° to 60° Celsius Weight 9 oz. (256 g)
GFK-1606A
Mixed DC I/O ModuleIC300DIQ511 / IC300DIQ611
12/24 Vdc In, Positive/Negative Logic24Vdc Out, Negative Logic
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
PAGE 20 10 NOV 1999 GFK-1601A
This Data Sheet (GFK-1606A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
2 WIRING
3 INTERNAL CIRCUIT SCHEMATIC
SignalPin
DIQ611 DIQ511I1 Input 1 Input 1I2 Input 2 Input 2I3 Input 3 Input 3I4 Input 4 Input 4I5 Input 5 No ConnectionI6 Input 6 No ConnectionI7 Input 7 No ConnectionI8 Input 8 No ConnectionC Common
Q1 Output 1 Output 1Q2 Output 2 Output 2Q3 Output 3 Output 3Q4 Output 4 Output 4Q5 Output 5 No ConnectionQ6 Output 6 No ConnectionQ7 Output 7 No ConnectionQ8 Output 8 No ConnectionVC CommonV+ Load Voltage +
To Controller
VCCI/O C onnector
C
I1
From C ontro ller
V +
Q
V C
I/O C onnec tor
*
OCS Bottom View – Shows corresponding I/O pin location
+ -
+-
12-24VDC
LOAD
+
-5-35VDC
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
I1
I2
I3
I4
Q1
Q2
Q3
Q4
V+
I5
I6
I7
I8
Q5
Q6
Q7
Q8
C
VC
DIQ611
*
+ - + - + - + - + - + - + - + -
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
GFK-1601A 10 NOV 1999 PAGE 21
This Data Sheet (GFK-1606A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
4 CONFIGURATION
Preliminary configuration procedures that are applicable to all SmartStack Modules are located in theControl Station Hardware Manual (GFK-1631).
Selecting the I/O Map tab provides information about the I/O registers, which are assigned to a specificSmartStack Module and where the module is located in the point map. The I/O Map is determined bythe model number and location within the SmartStack. The I/O Map is not edited by the user.
The Module Setup is used in applications where it is necessary to change the default states of theoutputs when the controller (e.g., OCS100) enters idle/stop mode. The default turns the outputs OFFwhen the controller enters idle/stop mode. By selecting the Module Setup tab, each output can be set toeither turn ON, turn OFF or to hold the last state. Generally, most applications use the default settings.
5 INSTALLATION / SAFETY
All applicable codes and standards should be followed in the installation of this product.
For detailed installation information, refer to Chapter Two in the Control Station Hardware Manual(GFK-1631). A handy checklist is provided that covers panel box layout requirements and minimumclearances.
6 OUTPUT CHARACTERISTICS
7 TECHNICAL ASSISTANCE
For user manual updates, contact GE Fanuc PLC Technical Services Hotline at 1-800-433-2682 or visitour website at www.gefanuc.com.
0 10 20 30 40 50 60 °C 32 50 68 86 104 122 140 °F
Derating Chart for DIQ511 /611
0
.1
.2
.3
.4
.5
AMPS
Warning: The default turns the outputs OFF when the controller enters idle/stop mode. To avoidinjury of personnel or damages to equipment, exercise extreme caution when changing the defaultsetting using the Module Setup tab.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
PAGE 22 10 NOV 1999 GFK-1601A
This Data Sheet (GFK-1606A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
NOTES
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
GFK-1601A 10 NOV 1999 PAGE 23
This Data Sheet (GFK-1607A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
1 SPECIFICATIONS
INPUT DIQ711 DIQ711Inputs per Module 16 Input Characteristics BidirectionalCommons perModule
3 Input Impedance 10K Ohms
Input Voltage Range 12-24VDC Minimum ON Current 1mAPeak Voltage 35VDC Max. Maximum OFF Current 200µAIsolation(Channel to Bus)
500VDC OFF to ON Response 1ms.
ON Voltage Level 9VDC ON to OFF Response 1ms.OFF Voltage Level 3VDC
OUTPUT DIQ711 DIQ711Outputs per Module 12 Output Protection Short Circuit, Reverse
PolarityCommons perModule 1 Maximum Leakage Current 100µA
Operating Voltage 5 - 35VDC Maximum Inrush Current 600mA.Output Type Sinking / 10K Pull-Up Minimum Load NonePeak Voltage 35VDC Max. OFF to ON Response 1ms.OutputCharacteristics Current Sinking ON to OFF Response 1ms.
ON Voltage Level 1.5VDC Max.Maximum LoadCurrent
0.5A Max.
General SpecificationsRequired Power(Steady State)
1.18W (49.5mA @ 24VDC) CE Refer to GFK-1755
Required Power (Inrush) Negligible UL Operating Temperature CodeT4A; Also refer to GFK-1754
Relative Humidity 5 to 95% Non-condensing Terminal Type Spring Clamp, RemovableOperating Temperature 0° to 60° Celsius Weight 9 oz. (256 g)
GFK-1607A
Mixed DC I/O ModuleIC300DIQ711
(16 Input Channels)12/24 Vdc In, Positive/Negative Logic
24Vdc Out, Negative Logic(12 Output Channels)
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
PAGE 24 10 NOV 1999 GFK-1601A
This Data Sheet (GFK-1607A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
2 WIRING
2.1 Input Wiring
SignalPin
DIQ711 InputI1 Input 1I2 Input 2I3 Input 3I4 Input 4I5 Input 5I6 Input 6I7 Input 7I8 Input 8C1 Common 1I9 Input 9I10 Input 10I11 Input 11I12 Input 12C2 Common 1I13 Input 13I14 Input 14I15 Input 15I16 Input 16C3 Common 3
OCS Top View – ShowsCorresponding I/O pin location
*
+ -
+-12-24V D C
I1
I2
I3
I4
I9
I10
I11
I12
C3
I5
I6
I7
I8
C2
I13
I14
I15
C1
I16
DIQ711
+ -
+-12-24V D C
+ -
+-12-24V D C
*
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
GFK-1601A 10 NOV 1999 PAGE 25
This Data Sheet (GFK-1607A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
2.2 Output Wiring
SignalPin
DIQ711 OutputC4 Common 4Q1 Output 1Q2 Output 2Q3 Output 3Q4 Output 4V1 Load Power 1C4 Common 4Q5 Output 5Q6 Output 6Q7 Output 7Q8 Output 8V2 Load Power 2C4 Common 4Q9 Output 9
Q10 Output 10Q11 Output 11Q12 Output 12V3 Load Power 3NC No Connection
D IQ 7115-35VD C
LOAD
+ -5-35VD C
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
C 4
Q 1
Q 2
Q 3
Q 7
Q 8
V2
C 4
Q 4
V1
C 4
Q 5
Q 9
Q 10
Q 11
Q 12
Q 6
V3
LOAD
LOAD
LOAD
LOAD
+ -5-35VD C
+ -
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-
+
-+
-
+
-
+
-
N C
*
*
OCS Bottom View – Showscorresponding I/O pin location
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
PAGE 26 10 NOV 1999 GFK-1601A
This Data Sheet (GFK-1607A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
3 INTERNAL CIRCUIT SCHEMATIC
4 CONFIGURATION
Preliminary configuration procedures that are applicable to all SmartStack Modules are located in theControl Station Hardware Manual (GFK-1631).
Selecting the I/O Map tab provides information about the I/O registers, which are assigned to a specificSmartStack Module and where the module is located in the point map. The I/O Map is determined bythe model number and location within the SmartStack. The I/O Map is not edited by the user.
The Module Setup is used in applications where it is necessary to change the default states of theoutputs when the controller (e.g., OCS100) enters idle/stop mode. The default turns the outputs OFFwhen the controller enters idle/stop mode. By selecting the Module Setup tab, each output can be set toeither turn ON, turn OFF or to hold the last state. Generally, most applications use the default settings.
To Controller
VCCI/O C onnector
C
I1
From C ontro ller
V +
Q
V C
I/O C onnec tor
Warning: The default turns the outputs OFF when the controller enters idle/stop mode. To avoidinjury of personnel or damages to equipment, exercise extreme caution when changing the defaultsetting using the Module Setup tab.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
GFK-1601A 10 NOV 1999 PAGE 27
This Data Sheet (GFK-1607A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
5 INSTALLATION / SAFETY
All applicable codes and standards should be followed in the installation of this product.
For detailed installation information, refer to Chapter Two in the Control Station Hardware Manual(GFK-1631). A handy checklist is provided that covers panel box layout requirements and minimumclearances.
6 OUTPUT CHARACTERISTICS
7 TECHNICAL ASSISTANCE
For user manual updates, contact GE Fanuc PLC Technical Services Hotline at 1-800-433-2682 or visitour website at www.gefanuc.com.
0 10 20 30 40 50 60 °C 32 50 68 86 104 122 140 °F
Derating Chart for DIQ711
0
.1
.2
.3
.4
.5
AMPS
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
PAGE 28 10 NOV 1999 GFK-1601A
This Data Sheet (GFK-1607A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
NOTES
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
GFK-1601A 10 NOV 1999 PAGE 29
This Data Sheet (GFK-1608A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
1 SPECIFICATIONS
INPUT DIQ512 DIQ612 DIQ512 DIQ612Inputs per Module 4 isolated 8 isolated Input Impedance > 10K OhmsCommons perModule
1 1 Minimum ON Current 1mA
Input Voltage Range 12/24VDC Maximum OFF Current 200µAPeak Voltage 35VDC Max. OFF to ON Response 1ms.ON Voltage level Min. 9VDC ON to OFF Response 1ms.OFF Voltage level Max. 3VDC
Isolation(Channel to bus)
500VDCStatus Indicator 4 8
OUTPUT DIQ512 DIQ612 DIQ512 DIQ612Outputs per Module 3 relay 6 relay Maximum Leakage
Current 5µA
Commons perModule
1 2 Maximum Inrush Current 3A
Output Type Relay Minimum Load NoneCoil Voltage 18-30VDC OFF to ON Response 6ms. TypicalContact Voltage 250VAC / 30VDC Max. ON to OFF Response .3ms. TypicalON Voltage drop 0.2V Max. Status Indicator 3 6Fuses 10A commonMaximum Loadcurrent (resistive) 3A
Isolation(Channel to bus)
500VDC
General SpecificationsRequired Power(Steady State)
0.23W (9.6mA @ 24VDC) CE Refer to GFK-1755
Required Power (Inrush) Negligible UL Refer to GFK-1754Relative Humidity 5 to 95% Non-condensing Terminal Type Spring Clamp, RemovableOperating Temperature 0° to 60° Celsius Weight 9 oz. (256 g)
GFK-1608A
Mixed I/O ModuleIC300DIQ512 / IC300DIQ612
12/24 Vdc In, Positive/Negative Logic3A Relay Out
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
PAGE 30 10 NOV 1999 GFK-1601A
This Data Sheet (GFK-1608A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
2 WIRING
3 INTERNAL CIRCUIT SCHEMATIC
SignalPinDIQ612 DIQ512
I1 Input 1 Input 1I2 Input 2 Input 2I3 Input 3 Input 3I4 Input 4 Input 4I5 Input 5 No ConnectionI6 Input 6 No ConnectionI7 Input 7 No ConnectionI8 Input 8 No ConnectionC1 Common 1Q1 Output 1 Output 1Q2 Output 2 Output 2Q3 Output 3 Output 3C2 Common 2Q4 Output 4 No ConnectionQ5 Output 5 No ConnectionQ6 Output 6 No ConnectionC3 Common 3 No ConnectionVC Relay Coil Voltage CommonV+ Relay Coil Voltage +
To Controlle r
VCCI/O Connector
C1
I1
+ 24V
+
�
+
�
+
�
Q 1
Q 2
Q 3
Q 4
Q 5
Q 6
C om U S B
C 2 C 3
I/O Connector
*
OCS Bottom View – Shows corresponding I/O pin location
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
18-30VDC
5-250VACOR
5-35VDC
I1
I2
I3
I4
Q1
Q2
Q3
C2
V+
I5
I6
I7
I8
Q4
Q5
Q6
C3
C1
VC
DIQ612
*
12-24VDC + - - +
-+
5-250VACOR
5-35VDC
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
GFK-1601A 10 NOV 1999 PAGE 31
This Data Sheet (GFK-1608A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
4 CONFIGURATION
Preliminary configuration procedures that are applicable to all SmartStack Modules are located in theControl Station Hardware Manual (GFK-1631).
Selecting the I/O Map tab provides information about the I/O registers, which are assigned to a specificSmartStack Module and where the module is located in the point map. The I/O Map is determined bythe model number and location within the SmartStack. The I/O Map is not edited by the user.
The Module Setup is used in applications where it is necessary to change the default states of theoutputs when the controller (e.g., OCS100) enters idle/stop mode. The default turns the outputs OFFwhen the controller enters idle/stop mode. By selecting the Module Setup tab, each output can be set toeither turn ON, turn OFF or to hold the last state. Generally, most applications use the default settings.
5 INSTALLATION / SAFETY
All applicable codes and standards are to be followed in the installation of this product.
For detailed installation information, refer to Chapter Two in the Control Station Hardware Manual(GFK-1631). A handy checklist is provided that covers panel box layout requirements and minimumclearances.
6 OUTPUT CHARACTERISTICS
Typical Relay Life (DIQ512 / 612)
Voltage (Resistive) Load Current 1 Amp 2 Amp 3 Amp30VDC 600K 250K 125K125VAC 750K 300K 150K250VAC 500K 200K 100K
2 Relays
0 10 20 30 40 50 60 °C 32 50 68 86 104 122 140 °F
Derating Chart for DIQ512 / 612
0
1
2
3
AMPS
6 Relays
4 Relays
4
Warning: The default turns the outputs OFF when the controller enters idle/stop mode. To avoidinjury of personnel or damages to equipment, exercise extreme caution when changing the defaultsetting using the Module Setup tab.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
PAGE 32 10 NOV 1999 GFK-1601A
This Data Sheet (GFK-1608A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
7 TECHNICAL SUPPORT
For user manual updates, contact GE Fanuc PLC Technical Services Hotline at 1-800-433-2682 or visitour website at www.gefanuc.com.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
GFK-1601A 10 NOV 1999 PAGE 33
This Data Sheet (GFK-1726) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
1 SPECIFICATIONS
INPUT DIQ712 DIQ712Inputs per Module 14 isolated Minimum ON Current 1mACommons perModule
3 Maximum OFF Current 200µA
Input Voltage Range 12/24VDC OFF to ON Response 1ms.Peak Voltage 35VDC Max. ON to OFF Response 1ms.ON Voltage level Min. 9VDCOFF Voltage level Max. 3VDC
Input Impedance > 10K Ohms
Isolation(Channel to bus)
500VDC
OUTPUT DIQ712 DIQ712Outputs per Module 10 relay Maximum Inrush Current 3ACommons perModule
2 Minimum Load None
Output Type Relay OFF to ON Response 6ms. TypicalCoil Voltage 18-30VDC ON to OFF Response .3ms. TypicalContact Voltage 250VAC / 30VDC Max. Fuses 10A common
ON Voltage drop 0.2V Max. Isolation(Channel to bus)
500VDC
Maximum Loadcurrent (resistive)
3A Maximum LeakageCurrent 5µA
TBA=To Be AnnouncedGeneral Specifications
Required Power(Steady State)
.19W(8mA @ 24VDC) CE Pending
Required Power (Inrush) Negligible UL PendingRelative Humidity 5 to 95% Non-condensing Terminal Type Spring Clamp, RemovableOperating Temperature 0° to 60° Celsius Weight 9.5 oz.
GFK-1726
Mixed I/O ModuleIC300DIQ712
12/24 Vdc In, Positive/Negative Logic3A Relay Out
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
PAGE 34 10 NOV 1999 GFK-1601A
This Data Sheet (GFK-1726) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
2 WIRING
2.1 Input / Output Connector WiringSignalPinDIQ712
I1 Input 1I2 Input 2I3 Input 3I4 Input 4C1 Common for
Inputs1,2,3,4Q1 Output 1Q2 Output 2Q3 Output 3Q4 Output 4Q5 Output 5C2 Common for Outputs
1,2,3,4,5Q6 Output 6Q7 Output 7Q8 Output 8Q9 Output 9Q10 Output 10C3 Common for Outputs
6,7,8,9,10VC Relay Coil power
common, connectedto bus common
internally.V+ Relay Coil Power,
+18 to +30VDC,90mA max.
*
OCS Bottom View – Shows corresponding I/O pin location
*
+ -
+-12 -24V D C
LO AD
+
-
LO AD
LO AD
LO AD
LO AD
LO AD
+
-
-
+18 -30V D C
5-250VACO R
5 -35V D C
5-250VACO R
5 -35V D C
I1
I2
I3
I4
Q 5
C 2
Q 6
Q 7
V+
C 1
Q 1
Q 2
Q 3
Q 8
Q 9
Q 10
C 3
Q 4
VC
D IQ 712
LO AD
LO AD
LO AD
LO AD
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
GFK-1601A 10 NOV 1999 PAGE 35
This Data Sheet (GFK-1726) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
2.2 Input Connector Wiring
3 INTERNAL CIRCUIT SCHEMATIC
To Controller
VCCI/O Connector
C1
I1
+18-30V
+
�
+
�
+
�
Q1
Q2
Q3
Q4
Q5
Q6
Com USB
C2 C3
I/O Connector
SignalPinDIQ712
I5 Input 5I6 Input 6I7 Input 7I8 Input 8C4 Common for Inputs
5,6,7,8I9 Input 9I10 Input 10I11 Input 11I12 Input 12I13 Input 13I14 Input 14
C5Common for
Inputs9,10,11,12,13,14
OCS Top View – Shows corresponding I/O pin location
*
+ -
+-12-24VD C
I5
I6
I7
I8
I13
I14
C5
C4
I9
I10
I11
I12
D IQ 712
+ -
+-12-24VD C
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
PAGE 36 10 NOV 1999 GFK-1601A
This Data Sheet (GFK-1726) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
4 CONFIGURATION
Preliminary configuration procedures that are applicable to all SmartStack Modules are located in theControl Station Hardware Manual (GFK-1631).
Selecting the I/O Map tab provides information about the I/O registers, which are assigned to a specificSmartStack Module and where the module is located in the point map. The I/O Map is determined bythe model number and location within the SmartStack. The I/O Map is not edited by the user.
The Module Setup is used in applications where it is necessary to change the default states of theoutputs when the controller (e.g., OCS100) enters idle/stop mode. The default turns the outputs OFFwhen the controller enters idle/stop mode. By selecting the Module Setup tab, each output can be set toeither turn ON, turn OFF or to hold the last state. Generally, most applications use the default settings.
5 INSTALLATION / SAFETY
All applicable codes and standards are to be followed in the installation of this product.
For detailed installation information, refer to Chapter Two in the Control Station Hardware Manual(GFK-1631). A handy checklist is provided that covers panel box layout requirements and minimumclearances.
6 OUTPUT CHARACTERISTICS
Derating Chart for DIQ712(Each group of 5)
2 Relays 3 Relays
0 10 20 30 40 50 60 °C 32 50 68 86 104 122 140 °F
0
1
2
3
AMPS
5 Relays
4 Relays
4
Warning: The default turns the outputs OFF when the controller enters idle/stop mode. To avoidinjury of personnel or damages to equipment, exercise extreme caution when changing the defaultsetting using the Module Setup tab.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
GFK-1601A 10 NOV 1999 PAGE 37
This Data Sheet (GFK-1726) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
Typical Relay Life (DIQ712)Voltage
(Resistive) No LoadLoad Current
1 Amp 2 Amp 3 Amp30VDC 600K 250K 125K125VAC 750K 300K 150K250VAC
20Million
500K 200K 100K
7 TECHNICAL SUPPORT
For user manual updates, contact GE Fanuc PLC Technical Services Hotline at 1-800-433-2682 or visitour website at www.gefanuc.com.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
PAGE 38 10 NOV 1999 GFK-1601A
This Data Sheet (GFK-1726) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
NOTES
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
GFK-1601A 10 NOV 1999 PAGE 39
This Data Sheet (GFK-1609A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
1 SPECIFICATIONS
INPUT DIQ516 DIQ616 DIQ516 DIQ616Inputs per Module 4 8 Input Characteristics BidirectionalCommons perModule
1 1 Input Impedance 10K Ohms
Input Voltage Range 12-24VDC Minimum ON Current 1mA
Peak Voltage 35VDC Max. Maximum OFF Current 200µAIsolation(Channel to Bus)
500VDC OFF to ON Response 1ms.
ON Voltage Level 9VDC ON to OFF Response 1ms.OFF Voltage Level 3VDC Status Indicator 4 8
OUTPUT DIQ516 DIQ616 DIQ516 DIQ616Outputs per Module 4 8 Maximum Inrush Current 650mACommons per Module 1 1 Minimum Load None
Operating Voltage 10 - 28VDC OFF to ON Response 1ms.Output Type Sourcing / 10K Pull-Down ON to OFF Response 1ms.Peak Voltage 28VDC Max. Output Characteristics Current SourcingMaximum Load Current 0.5A Max. Status Indicator 4 8Output Protection Short Circuit
General SpecificationsRequired Power(Steady State)
0.14W (6.05mA @ 24VDC) CE Refer to GFK-1755
Required Power (Inrush) Negligible UL Refer to GFK-1754Relative Humidity 5 to 95% Non-condensing Terminal Type Spring Clamp, RemovableOperating Temperature 0° to 60° Celsius Weight 9 oz. (256 g)
GFK-1609A
Mixed DC I/O ModuleIC300DIQ516 / IC300DIQ616
12/24 Vdc In, Positive/Negative Logic24Vdc Out, Positive Logic
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
PAGE 40 10 NOV 1999 GFK-1601A
This Data Sheet (GFK-1609A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
2 WIRING
3 INTERNAL CIRCUIT SCHEMATIC
SignalPin
DIQ616 DIQ516I1 Input 1 Input 1I2 Input 2 Input 2I3 Input 3 Input 3I4 Input 4 Input 4I5 Input 5 No ConnectionI6 Input 6 No ConnectionI7 Input 7 No ConnectionI8 Input 8 No ConnectionC Common
Q1 Output 1 Output 1Q2 Output 2 Output 2Q3 Output 3 Output 3Q4 Output 4 Output 4Q5 Output 5 No ConnectionQ6 Output 6 No ConnectionQ7 Output 7 No ConnectionQ8 Output 8 No ConnectionVC CommonV+ Load Voltage +
To Controller
VCCI/O C onnector
C
I1
*
OCS Bottom View – Shows corresponding I/O pin location
V+
Q
FromController
VC
I/O Connector
*
+ -
+-1 2-2 4 V D C
LO A D
+
-1 0-2 8 V D C
LO A D
LO A D
LO A D
LO A D
LO A D
LO A D
LO A D
I1
I2
I3
I4
Q1
Q2
Q3
Q4
V+
I5
I6
I7
I8
Q5
Q6
Q7
Q8
C
VC
DIQ 616
+-
+-
+-
+-
+-
+-
+-
+-
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
GFK-1601A 10 NOV 1999 PAGE 41
This Data Sheet (GFK-1609A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
4 CONFIGURATION
Preliminary configuration procedures that are applicable to all SmartStack Modules are located in theControl Station Hardware Manual (GFK-1631).
Selecting the I/O Map tab provides information about the I/O registers, which are assigned to a specificSmartStack Module and where the module is located in the point map. The I/O Map is determined bythe model number and location within the SmartStack. The I/O Map is not edited by the user.
The Module Setup is used in applications where it is necessary to change the default states of theoutputs when the controller (e.g., OCS100) enters idle/stop mode. The default turns the outputs OFFwhen the controller enters idle/stop mode. By selecting the Module Setup tab, each output can be set toeither turn ON, turn OFF or to hold the last state. Generally, most applications use the default settings.
5 INSTALLATION / SAFETY
All applicable codes and standards are to be followed in the installation of this product.
For detailed installation information, refer to Chapter Two in the Control Station Hardware Manual(GFK-1631). A handy checklist is provided that covers panel box layout requirements and minimumclearances.
6 OUTPUT CHARACTERISTICS
7 TECHNICAL ASSISTANCE
For user manual updates, contact GE Fanuc PLC Technical Services Hotline at 1-800-433-2682 or visitour website at www.gefanuc.com.
0 10 20 30 40 50 60 °C 32 50 68 86 104 122 140 °F
Derating Chart for DIQ516 /616
0
.1
.2
.3
.4
.5
AMPS
Warning: The default turns the outputs OFF when the controller enters idle/stop mode. To avoidinjury of personnel or damages to equipment, exercise extreme caution when changing the defaultsetting using the Module Setup tab.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
PAGE 42 10 NOV 1999 GFK-1601A
This Data Sheet (GFK-1609A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
NOTES
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
GFK-1601A 10 NOV 1999 PAGE 43
This Data Sheet (GFK-1610A) is published individually & also as a part of SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
1 SPECIFICATIONS
INPUT DIQ716 DIQ716Inputs per Module 16 Input Characteristics BidirectionalCommons perModule
3 Input Impedance 10K Ohms
Input Voltage Range 12-24VDC Minimum ON Current 1mA
Peak Voltage 35VDC Max. Maximum OFF Current 200µAIsolation(Channel to Bus)
500VDC OFF to ON Response 1ms.
ON Voltage Level 9VDC /1mA minimum ON to OFF Response 1ms.OFF Voltage Level 3VDC
OUTPUT DIQ716 DIQ716Outputs per Module 12 Maximum Inrush Current 650mACommons per Module 1 Minimum Load None
Operating Voltage 10 - 28VDC OFF to ON Response 1ms.Output Type Sourcing / 10K Pull-Down ON to OFF Response 1ms.Peak Voltage 28VDC Max. Output Characteristics Current SourcingMaximum Load Current 0.5A Max. Output Protection Short Circuit
General SpecificationsRequired Power(Steady State)
0.13W (5.5mA @ 24VDC) CE Refer to GFK-1755
Required Power (Inrush) Negligible UL Operating Temperature CodeT4; Also refer to GFK-1754
Relative Humidity 5 to 95% Non-condensing Terminal Type Spring Clamp, RemovableOperating Temperature 0° to 60° Celsius Weight 9 oz. (256 g)
GFK-1610A
Mixed DC I/O ModuleIC300DIQ716
12/24 Vdc In, Positive/Negative Logic(16 Input Channels)
10-28Vdc Out, Positive Logic(12 Output Channels)
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
PAGE 44 10 NOV 1999 GFK-1601A
This Data Sheet (GFK-1610A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
2 WIRING
2.1 Input Wiring
SignalPin
DIQ716 INPUTI1 Input 1I2 Input 2I3 Input 3I4 Input 4I5 Input 5I6 Input 6I7 Input 7I8 Input 8C1 Common 1 (Isolated)I9 Input 9I10 Input 10I11 Input 11I12 Input 12C2 Common 2 (Isolated)I13 Input 13I14 Input 14I15 Input 15I16 Input 16C3 Common 3 (Isolated)
+ -
+-12-24V DC
I1
I2
I3
I4
I9
I10
I11
I12
C 3
I5
I6
I7
I8
C 2
I13
I14
I15
C 1
I16
D IQ 716
+ -
+-12-24V DC
+ -
+-12-24V DC
*
OCS Top View – ShowsCorresponding I/O pin location
*
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
GFK-1601A 10 NOV 1999 PAGE 45
This Data Sheet (GFK-1610A) is published individually & also as a part of SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
2.2 Output Wiring
SignalPin
DIQ716 OUTPUT C4 CommonQ1 Output 1Q2 Output 2Q3 Output 3Q4 Output 4V1 Load Power 1C4 CommonQ5 Output 5Q6 Output 6Q7 Output 7Q8 Output 8V2 Load Power 2C4 CommonQ9 Output 9
Q10 Output 10Q11 Output 11Q12 Output 12V3 Load PowerNC No Connection
C4
Q1
Q2
Q3
Q7
Q8
V2
C4
Q4
V1
C4
Q5
Q9
Q10
Q11
Q12
Q6
V3
DIQ716
+-10-28VDC
LOAD+-
LOAD+-
LOAD+-
LOAD+-
+-10-28VDC
LOAD+-
LOAD+-
LOAD+-
LOAD+-
+-10-28VDC
LOAD+-
LOAD+-
LOAD+-
LOAD+-
NC
*
*
OCS Bottom View – Shows corresponding I/O pin location
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
PAGE 46 10 NOV 1999 GFK-1601A
This Data Sheet (GFK-1610A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
3 INTERNAL CIRCUIT SCHEMATIC
4 CONFIGURATION
Preliminary configuration procedures that are applicable to all SmartStack Modules are located in theControl Station Hardware Manual (GFK-1631).
Selecting the I/O Map tab provides information about the I/O registers, which are assigned to a specificSmartStack Module and where the module is located in the point map. The I/O Map is determined bythe model number and location within the SmartStack. The I/O Map is not edited by the user.
The Module Setup is used in applications where it is necessary to change the default states of theoutputs when the controller (e.g., OCS100) enters idle/stop mode. The default turns the outputs OFFwhen the controller enters idle/stop mode. By selecting the Module Setup tab, each output can be set toeither turn ON, turn OFF or to hold the last state. Generally, most applications use the default settings.
5 INSTALLATION / SAFETY
All applicable codes and standards are to be followed in the installation of this product.
For detailed installation information, refer to Chapter Two in the Control Station Hardware Manual(GFK-1631). A handy checklist is provided that covers panel box layout requirements and minimumclearances.
V+
Q
FromController
VC
I/O Connector
To Controller
VCCI/O Connector
C
I1
Warning: The default turns the outputs OFF when the controller enters idle/stop mode. To avoidinjury of personnel or damages to equipment, exercise extreme caution when changing the defaultsetting using the Module Setup tab.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
GFK-1601A 10 NOV 1999 PAGE 47
This Data Sheet (GFK-1610A) is published individually & also as a part of SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
6 OUTPUT CHARACTERISTICS
7 TECHNICAL ASSISTANCE
For user manual updates, contact GE Fanuc PLC Technical Services Hotline at 1-800-433-2682 or visitour website at www.gefanuc.com.
0 10 20 30 40 50 60 °C 32 50 68 86 104 122 140 °F
Derating Chart for HE800DIQ716
0
.1
.2
.3
.4
.5
AMPS
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
PAGE 48 10 NOV 1999 GFK-1601A
This Data Sheet (GFK-1610A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
NOTES
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
GFK-1601A 10 NOV 1999 PAGE 49
This Data Sheet (GFK-1611A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
1 SPECIFICATIONS
INPUT DIQ522 DIQ622 DIQ522 DIQ622Inputs per Module 4 8 Input Impedance 0.01µF +10K
Commons per Module 1 Isolation( Channel to Bus)
500VDC
Input Voltage Range 120 – 160 VAC Minimum ON Current 1mA.Peak Voltage 160VAC Maximum OFF Current 200µA.AC Frequency 60Hz OFF to ON Response 50ms.ON Voltage Level 70VAC Min. ON to OFF Response 50ms.OFF Voltage level 30VAC Max. Status Indicator 4 8
OUTPUT DIQ522 DIQ622 DIQ522 DIQ622Outputs per Module 3 relay 6 relay Maximum Leakage
Current 5µA
Commons perModule
1 2 Maximum Inrush Current 3A
Output Type Relay Minimum Load NoneCoil Voltage 18-30VDC OFF to ON Response 6ms. TypicalContact Voltage 250VAC / 30VDC Max. ON to OFF Response .3ms. TypicalON Voltage drop .1V Max. Status Indicator 3 6Fuses 10A commonMaximum Loadcurrent (resistive)
3AIsolation(Channel to bus)
500VDC
General SpecificationsRequired Power (Steady State) 0.06 (2.75 @ 24VDC) CE Rating See GFK-1755Required Power (Inrush) Negligible UL Operating Temperature
Code T4A; Also refer toGFK-1754
Relative Humidity 5 to 95% Non-condensing Terminal Type Spring Clamp, RemovableOperating Temperature 0° to 60° Celsius Weight 9oz.
GFK-1611A
AC Input /AC OutputModule
IC300DIQ522 / IC300DIQ622120 VAC In, Positive Logic
3A Relay Out
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
PAGE 50 10 NOV 1999 GFK-1601A
This Data Sheet (GFK-1611A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
2 WIRING
SignalPin
DIQ622 DIQ522I1 Input 1 Input 1I2 Input 2 Input 2I3 Input 3 Input 3I4 Input 4 Input 4I5 Input 5 No ConnectionI6 Input 6 No ConnectionI7 Input 7 No ConnectionI8 Input 8 No ConnectionC1 Common 1Q1 Output 1 Output 1Q2 Output 2 Output 2Q3 Output 3 Output 3C2 Common 2Q4 Output 4 No ConnectionQ5 Output 5 No ConnectionQ6 Output 6 No ConnectionC3 Common 3 No ConnectionsVC Relay Coil Voltage CommonV+ Relay Coil Voltage +
*
OCS Bottom View – Shows corresponding I/O pin location
LOAD
LOAD
LOAD
LOAD
LOAD
LOAD
-
+18-30VDC
5-250VACOR
5-35VDC
5-250VACOR
5-35VDC
I1
I2
I3
I4
Q1
Q2
Q3
C2
V+
I5
I6
I7
I8
Q4
Q5
Q6
C3
C1
VC
DIQ622
L
N
120VAC
*
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
GFK-1601A 10 NOV 1999 PAGE 51
This Data Sheet (GFK-1611A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
3 INTERNAL CIRCUIT SCHEMATICS
4 CONFIGURATION
Preliminary configuration procedures that are applicable to all SmartStack Modules are located in theControl Station Hardware Manual (GFK-1631).
Selecting the I/O Map tab provides information about the I/O registers, which are assigned to a specificSmartStack Module and where the module is located in the point map. The I/O Map is determined bythe model number and location within the SmartStack. The I/O Map is not edited by the user.
The Module Setup is used in applications where it is necessary to change the default states of theoutputs when the controller (e.g., OCS100) enters idle/stop mode. The default turns the outputs OFFwhen the controller enters idle/stop mode. By selecting the Module Setup tab, each output can be set toeither turn ON, turn OFF or to hold the last state. Generally, most applications use the default settings.
VCC
To Controller
I/O Connector
I1
IC
+ 2 4 V
+
�
+
�
+
�
Q 1
Q 2
Q 3
Q 4
Q 5
Q 6
C om U S B
C 2 C 3
I/O Connec tor
Warning: The default turns the outputs OFF when the controller enters idle/stop mode. To avoidinjury of personnel or damages to equipment, exercise extreme caution when changing the defaultsetting using the Module Setup tab.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
PAGE 52 10 NOV 1999 GFK-1601A
This Data Sheet (GFK-1611A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
5 INSTALLATION / SAFETY
All applicable codes and standards are to be followed in the installation of this product.
For detailed installation information, refer to Chapter Two in the Control Station Hardware Manual(GFK-1631). A handy checklist is provided that covers panel box layout requirements and minimumclearances.
6 OUTPUT CHARACTERISTICS
Typical Relay Life (DIQ522 / 622)
Voltage (Resistive) Load Current 1 Amp 2 Amp 3 Amp30VDC 600K 250K 125K125VAC 750K 300K 150K250VAC 500K 200K 100K
7 TECHNICAL SUPPORT
For user manual updates, contact GE Fanuc PLC Technical Services Hotline at 1-800-433-2682 or visitour website at www.gefanuc.com.
2 Relays
0 10 20 30 40 50 60 °C 32 50 68 86 104 122 140 °F
Derating Chart for DIQ522 / 622
0
1
2
3
AMPS
6 Relays
4 Relays
4
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
GFK-1601A 10 NOV 1999 PAGE 53
This Data Sheet (GFK-1727) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
1 SPECIFICATIONS
INPUT DIQ722 DIQ722Inputs per Module 14 Input Impedance 0.01µF +10K
Commons per Module 3 Isolation( Channel to Bus)
500VDC
Input Voltage Range 120 – 160 VAC Minimum ON Current 1mA.Peak Voltage 160VAC Maximum OFF Current 200µA.AC Frequency 60Hz OFF to ON Response 50ms.ON Voltage Level 70VAC Min. ON to OFF Response 50ms.OFF Voltage level 30VAC Max.
OUTPUT DIQ722 DIQ722
Outputs per Module 10 relay Maximum LeakageCurrent 5µA
Commons perModule
2 Maximum Inrush Current 3A
Output Type Relay Minimum Load NoneCoil Voltage 18-30VDC OFF to ON Response 6ms. TypicalContact Voltage 250VAC / 30VDC Max. ON to OFF Response .3ms. TypicalON Voltage drop 0.2VDC max.Fuses 10A commonMaximum Loadcurrent (resistive)
3A
Isolation(Channel to bus) 500VDC
General SpecificationsRequired Power (Steady State) .17W(7mA @ 24VDC) CE Rating PendingRequired Power (Inrush) Negligible UL PendingRelative Humidity 5 to 95% Non-condensing Terminal Type Spring Clamp, RemovableOperating Temperature 0° to 60° Celsius Weight 9.5 oz.
GFK-1727
AC Input /AC OutputModule
IC300DIQ722120 VAC In, Positive Logic
3A Relay Out
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
PAGE 54 10 NOV 1999 GFK-1601A
This Data Sheet (GFK-1727) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
2 WIRING
2.1 Input / Output Connector Wiring
*
OCS Bottom View – Shows corresponding I/O pin location
SignalPinDIQ722
I1 Input 1I2 Input 2I3 Input 3I4 Input 4C1 Common for Inputs1,2,3,4Q1 Output 1Q2 Output 2Q3 Output 3Q4 Output 4Q5 Output 5C2 Common for Outputs 1,2,3,4,5Q6 Output 6Q7 Output 7Q8 Output 8Q9 Output 9Q10 Output 10C3 Common for Outputs 6,7,8,9,10VC Relay Coil power common,
connected to bus commoninternally.
V+ Relay Coil power + 18 to+30VDC, 90mA max.
*
L
N120VAC
LO AD
+
-
LO AD
LO AD
LO AD
LO AD
LO AD
+
-
-
+18-30VDC
5-250VACOR
5-35VDC
5-250VACOR
5-35VDC
I1
I2
I3
I4
Q 5
C2
Q 6
Q 7
V+
C1
Q 1
Q 2
Q 3
Q 8
Q 9
Q 10
C3
Q 4
VC
DIQ 722
LO AD
LO AD
LO AD
LO AD
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
GFK-1601A 10 NOV 1999 PAGE 55
This Data Sheet (GFK-1727) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
2.2 Input Connector Wiring
3 INTERNAL CIRCUIT SCHEMATICS
+18-30VDC
+
�
+
�
+
�
Q1
Q2
Q3
Q4
Q5
Q6
Com USB
C2 C3
I/O Connector
VCC
To Controller
I/O Connector
I1
IC
SignalPinDIQ722
I5 Input 5I6 Input 6I7 Input 7I8 Input 8C4 Common for
Inputs 5,6,7,8I9 Input 9I10 Input 10I11 Input 11I12 Input 12I13 Input 13I14 Input 14
C5Common for
Inputs9,10,11,12,13,14
OCS Top View – Shows corresponding I/O pin location
*
*I5I6
I7
I8
I13
I14
C 5
C 4
I9
I10
I11
I12
D IQ 722
L
N120VA C
L
N120VA C
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
PAGE 56 10 NOV 1999 GFK-1601A
This Data Sheet (GFK-1727) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
4 CONFIGURATION
Preliminary configuration procedures that are applicable to all SmartStack Modules are located in theControl Station Hardware Manual (GFK-1631).
Selecting the I/O Map tab provides information about the I/O registers, which are assigned to a specificSmartStack Module and where the module is located in the point map. The I/O Map is determined bythe model number and location within the SmartStack. The I/O Map is not edited by the user.
The Module Setup is used in applications where it is necessary to change the default states of theoutputs when the controller (e.g., OCS100) enters idle/stop mode. The default turns the outputs OFFwhen the controller enters idle/stop mode. By selecting the Module Setup tab, each output can be set toeither turn ON, turn OFF or to hold the last state. Generally, most applications use the default settings.
5 INSTALLATION / SAFETY
All applicable codes and standards are to be followed in the installation of this product.
For detailed installation information, refer to Chapter Two in the Control Station Hardware Manual(GFK-1631). A handy checklist is provided that covers panel box layout requirements and minimumclearances.
6 OUTPUT CHARACTERISTICS
Derating Chart for DIQ722(Each group of 5)
2 Relays 3 Relays
0 10 20 30 40 50 60 °C 32 50 68 86 104 122 140 °F
0
1
2
3
AMPS
5 Relays
4 Relays
4
Warning: The default turns the outputs OFF when the controller enters idle/stop mode. To avoidinjury of personnel or damages to equipment, exercise extreme caution when changing the defaultsetting using the Module Setup tab.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
GFK-1601A 10 NOV 1999 PAGE 57
This Data Sheet (GFK-1727) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
Typical Relay Life (DIQ722)Voltage
(Resistive) No LoadLoad Current
1 Amp 2 Amp 3 Amp30VDC 600K 250K 125K125VAC 750K 300K 150K250VAC
20Million
500K 200K 100K
7 TECHNICAL SUPPORT
For user manual updates, contact GE Fanuc PLC Technical Services Hotline at 1-800-433-2682 or visitour website at www.gefanuc.com.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
PAGE 58 10 NOV 1999 GFK-1601A
This Data Sheet (GFK-1727) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
NOTES
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
GFK-1601A 10 NOV 1999 PAGE 59
This Data Sheet (GFK-1612A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
1 SPECIFICATIONS
INPUT DIQ524 DIQ624 DIQ524 DIQ624Inputs per Module 4 8 Input Impedance 0.01µF +10K
Commons per Module 1 1 Isolation( Channel to Bus)
500VDC
Input Voltage Range 120 – 160 VAC Minimum ON Current 1ms.Peak Voltage 160VAC Maximum OFF Current 1ms.AC Frequency 60Hz OFF to ON Response 50ms.ON Voltage Level 70VAC Min. ON to OFF Response 50ms.OFF Voltage level 30VAC Max. Status Indicator 4 8
OUTPUT DIQ524 DIQ624 DIQ524 DIQ624Outputs per Module 4 8 Maximum Load Current .3A Max.Commons per Module 1 1 Maximum Leakage Current 15µA Max.Operating voltage 260VAC Max. Maximum Inrush Current 500mAOutput Type MOSFET OFF to ON Response 10ms. Max.Contact Voltage 260VAC Max. ON to OFF Response 3ms. Max. ON Voltage level 1V Max.Isolation(Channel to bus)
500VDCStatus Indicator 4 8
General SpecificationsRequired Power (Steady State) 0.18W (7.7mA @ 24VDC) CE Refer to GFK-1755Required Power (Inrush) Negligible UL Refer to GFK-1754Relative Humidity 5 to 95% Non-condensing Terminal Type Spring Clamp, RemovableOperating Temperature 0° to 60° Celsius Weight 9.5 oz. (256 g)
GFK-1612A
AC Input /AC OutputModule
IC300DIQ524 / IC300DIQ624120 VAC In, Positive Logic
80-240 VAC Out, Positive Logic
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
-
PAGE 60 10 NOV 1999 GFK-1601A
This Data Sheet (GFK-1612A) is published individually & also as a part of the SmartStack Supplement (GFK-1601A).Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.
2 WIRING
3 INTERNAL CIRCUIT SCHEMATICS
SignalPin
DIQ624 DIQ524I1 Input 1 Input 1I2 Input 2 Input 2I3 Input 3 Input 3I4 Input 4 Input 4I5 Input 5 No ConnectionI6 Input 6 No ConnectionI7 Input 7 No ConnectionI8 Input 8 No ConnectionIC Input CommonQ1 Output 1 Output 1Q2 Output 2 Output 2Q3 Output 3 Output 3Q4 Output 4 Output 4Q5 Output 5 No ConnectionQ6 Output 6 No ConnectionQ7 Output 7