Arjo Freedom Bath Manual

5/18/2018 Arjo Freedom Bath Manual

1/48

Freedom Bath

...with people in mind

0086

INSTRUCTIONS FOR USE

04.AF.02_11US.CA . Juni 2013


2/48

WARNINGTo avoid in jury, always read this Instructions for Use and accompanied documentsbefore using the product .

Mandatory to read the Instructions for Use

Design Policy and Copyright and are trademarks belonging to the ArjoHuntleigh group of companies. ArjoHuntleigh 2013.

As our policy is one of continuous improvement, we reserve the right to modify designs

without prior notice.The content of this publication may not be copied either whole or inpart without the consent of ArjoHuntleigh.


3/48

3

Contents

Foreword ..........................................................................4

Intended Use .................................................................... 5

Safety Instructions ............................................................ 6

Preparations ..................................................................... 7

Parts Designation ............................................................. 8

Control Panel, External Water Supply ............................ 10

Control Panel, Built-In Water Supply .............................. 12

Product Description/Function ......................................... 14

Power Assisted Door Operation ..................................... 16

Operating Assisted Bathing ......................................... 17

Air Spa Operation (optional) ........................................... 20

Waste Water Pan ........................................................... 21

Home Care Use .............................................................. 22

Cleaning and Disinfection Instructions ........................... 24

Care and Preventive Maintenance ................................. 28

Troubleshooting .............................................................. 32

Technical Specifications ................................................. 34

Labels on the Freedom Bath .......................................... 38

Approvals and List of Standards ..................................... 40

Electromagnetic Compatibility ........................................ 42

Parts and Accessories .................................................... 46

ArjoHuntleigh Addresses .................................... Last page


4/48

4

Foreword

Thank you for purchasing ArjoHuntleighEquipment.Your Freedom Bathis part of a world-wide family of

quality products designed especially for assisted

living facilities, group homes, retirement facilities,moderately dependent nursing care and in homes

wherever limited assistance or independent bathing

equipment is desired.

Please contact us if you have any questions about the

operation or maintenance of your Freedom Bath.

Please read this Instructions for Usethoroughly!

Please read thisInstructions for Use (IFU)in itsentirety before using your Freedom Bath.

Information in theIFUis crucial to the properoperation and maintenance of the equipment, andwill help protect your product and make sure that theequipment performs to your satisfaction. Some of theinformation in thisIFUis important for your safetyand must be read and understood to help prevent

possible injury.

Unauthorized modifications on any ArjoHuntleighequipment may affect its safety. ArjoHuntleigh willnot be held responsible for any accidents, incidentsor lack of performance that occur as a result of any

unauthorized modification to its products.

Report Unexpected Operations orEventsContact your local ArjoHuntleigh representative if

any unexpected operations or events occur. The

contact information appear on the last page of this

IFU.

Service and SupportA service routine must be performed on your

Freedom Bathevery year by ArjoHuntleigh

authorized service personnel to ensure continued safe

operation of your product.

See sectionCare and Preventive Maintenance.

If you require further information, please contactyour local ArjoHuntleigh representative who canoffer comprehensive support and service programs tomaximize the long-term safety, reliability and valueof the product.

Contact your local ArjoHuntleigh representative forreplacement parts. Your service representative stocksthe parts you will need. The contact informationappears on the last page of thisIFU.

Definitions in this IFU:

Means:

Safety warning. Failure to understand and obey this

warning may result in injury to you or to others

Means:

Failure to follow these instructions may cause

damage to all or parts of the system.

Means:

This is important information for the correct use of

this system or equipment.

Means:The name and address of the manufacturer

WARNING

CAUTION

NOTE


5/48

5

Intended Use

This equipment must be used in accordance withthese safety instructions.

Anyone using th is equipment must also have readand understood the instruct ions in this Instructions

for Use (IFU).If there is anything you are not sure about, ask yourAr joHunt leigh representative.

Freedom bathis intended for therapeutic bathing and

showering of adult residents in care facilities or in home care

environment.

The bath must be used by appropriately trained caregivers with

adequate knowledge of the care environment, its common

practices and procedures, and in accordance with the

guidelines in theInstructions for Use (IFU).

Indication for UseThis bath is used for general cleaning and relaxation and for

hydrotherapy to relieve pain and itching and as an aid in the

healing process of inflamed and traumatized tissue, and it

serves as a setting for removal of contaminated tissue.

This equipment should only be used for the purpose specified

in thisInstructions for Use (IFU). Any other use is prohibited.

Resident Assessment

We recommend that facilities establish regular assessmentroutines. Caregivers must assess each resident according to the

following criteria prior to use:

The resident must be able to sit in an upright position, nor-

mally defined as active or semi-active.

The residents weight must not exceed 160 kg (352 lbs).

The resident must understand and be able to respond to

instructions to stay seated in an upright position.

If a resident does not meet these criteria an alternative

equipment/system should be used.

Lifetime of the EquipmentThe equipment must be installed by appropriately trained

personnel according to the Assembly and Installation

Instructions. Requirements in the Assembly and Installation

Instructions can only be superseded by local code.

The lifetime of this equipment is ten (10) years and the service

life of the support strap (optional) is two (2) years. The lifetime

and service life are stated providing that the preventive

maintenance are being carried out in accordance with theinstructions for care and maintenance in theInstructions for

use (IFU). This bath system must only be used for the purpose

specified here.


6/48

6

Safety Instructions

WARNINGTo avoid injury, make sure that the resident is not

left unattended at any time.

WARNINGTo avoid electric shock, never use other electr icalequipment near this device.

WARNINGTo avoid explosion or fi re, never use the equipmentin oxygen rich environment, in presence of heatsource or flammable anaesthetic gases.

CAUTIONNever drop or insert any object into any opening.Do not probe into the drain with any pointed orsharp object.

Do not force door down before tub empties anddoor seal deflates.

NOTEPressing the emergency seal release valve with waterin the tub will cause the water to spill onto the bathroomfloor.

If the door is not fully raised, the drain will remain open.

If the fully raised door is forced down, the drain willopen.The fully raised door will remain sealed as long as waterremains in the tub and the emergency door seal releasevalve is not activated.

In the event of an AC power failure, the drain will openbut the seal will remain inflated until the emergency sealrelease valve is activated.


7/48

7

Preparations

Site PreparationsPrior to installation of Freedom Baththe floorand walls within the required area must befinished.

Material: The floor should be made of a slip-resistantmaterial, free of bumps.

Floor slope: When using a floor drain, the slopetowards the drain should not exceed 1:50.

Floor attachments:The floor construction must besuitable for anchoring the bolts.

Actions Before the First Use (9 Steps)1 Make sure that the bath has been installed

according to theAssembly and Installation

Instructions.

2 Check that all parts of the product are supplied.

Compare with the Parts Designationpage in this

IFU. If any part is missing or damaged - do NOT

use the product.

3 Read theIFU.

4 Disinfect the product according toDisinfection

Instructionsin thisIFU.5 Perform a functionality test according to Care and

Preventive Maintenancein thisIFU.

6 Choose a designated area, where theIFUshould

be kept and is easily accessible at all times.

8 Make sure the thermostatic mixer has been

calibrated according to theAssembly and

Installation Instructionsby an ArjoHuntleigh

service technician.

9 Make sure to have a rescue plan ready in case of a

resident emergency.

7 WARNINGTo prevent scalding, make sure that thewater mixer has been calibrated.

Confirm that responsible organizationhas established calibration routines.

Actions Before Every Use (4 Steps)1 Check that all parts are in place. Compare to Parts

Designationpage in thisIFU.

2 Check bath and accessories for damage.

3 If any part is missing or damaged - do NOT use

the product.

4 WARNINGTo prevent cross-contamination, alwaysfollow the disinfection instructions inthis Instructions for Use.

NOTE

If you have any questions, please contact yourlocal ArjoHuntleigh representative for supportand service. The contact information(ArjoHuntleigh addresses)is listed on the lastpage of this IFU.


8/48

8

Parts Designation

Freedom BathIncludes the Following Parts:(See Fig. 1)

1 Roll-Door

2 Covers for service access (2)3 Low water level sensors (2)

4 Emergency seal release

5 Drain

6 Assist handle

7 Inflatable sealing system (inside the cover)

8 Seat

9 Waste water pan (underneth the tub)

10 Shower

11 Tub fill spout

12 Thermostatic water control system (optional)

13 Control panel

14 High water level sensor (optional)

15 Surface overflow outlet

16 Support strap (optional)

Air Spa (opt ional ) (See Fig. 2)17 Control panel18 Disinfectant fill port for MultiClean (optional)

19 High water level sensor (1)

20 Air nozzles (12)

Applied part: Type BRoll door. including the complete tub.Protection against electrical shock in

accordance with IEC 60601-1.


9/48

9

1 12 13 10 6 11 4

14

2

9

7

8 3 5

17

16

18

19

1

2

20

15


10/48

10

Control Panel, External Water Supply

Control Panel - Still Bath (6 steps)1 Door - UP

2 Door seal/ Drain

3 LED- flashes during sealing operation

- steady green light when sealing is activated

4 Door - DOWN

5 Shows water temperature in tub.

6 LED, steady red light when all buttons are locked.

Activates/releases when button 1 and button 4 are pushed at

the same time for 1 second.

Control Panel - Air Spa (8 steps)1 Door - UP

2 Door seal / Drain

3 LED

- flashes during sealing operation

- steady green light when sealing is activated

4 Door - DOWN

5 Shows water temperature in tub.




7 Air spa- START/STOP.

Five minutes after the tub is emptied, the air-

blower activates for 60 seconds (not in combination with

MultiClean).

8 Air spa- INCREASE/DECREASE

AIR SPEED.


11/48

11

F r e e d o m B a t h

Control Panel - Still Bath

6

1 2 4 53

Control Panel - Air Spa

F r e e d o m B a t h

1 2 3 4 5

6 7 8


12/48

12

Control Panel, Built-In Water Supply

Control Panel - Still Bath1 Door - UP.

2 Door seal / Drain

3 LED- flashes during sealing operation.

- steady green light when sealing is activated.

4 Door - DOWN.

5 Shows water temperature (measured in the

thermostatic mixer).

6 Tub filling




8 Resident shower

9 Mixer knob - INCREASE/DECREASE

TUBWATER TEMPERATURE

Control Panel - Air Spa1 Door - UP.

2 Door seal / Drain

3 LED

- flashes during sealing operation.

- steady green light when sealing is activated.

4 Door - DOWN.

5 Shows water temperature (measured in the

thermostatic mixer).

6 Tub filling.




8 Resident shower.

9 Air spa- START/STOP.

Five minutes after the tub is emptied, the air-

blower activates for 60 seconds (not in combination with

MultiClean).

10 Air spa- INCREASE/DECREASE

AIR-SPEED.

11 Mixer knob - INCREASE/DECREASE

TUBWATER TEMPERATURE.


13/48

13

Freedom Bath

Control Panel - Still Bath

1 2 3 4 5

6 7 8 9

Freedom Bath

Control Panel - Air Spa

1 2 3 4 5

76 8 9 10 11


14/48

14

Product Description/Function

Power Operated DoorThe power operated door has a gear motor which is

operated from the control panel. The motor incorporates a push

and hold feature and a safety clutch for user safety. The clutch

disengages when the control button is released, permitting thedoor to be opened in a manual mode, but should only be used

in emergency.

In case of power failure the door can be opened manually when

pushing the emergency button. (See Fig. 1)

Still Bath/Air SpaThe Freedom Bathis available with or without an air spa

system. A low-water sensor will prevent the air spa systemfrom being activated until the water in the tub is at a proper

operating level.

See sectionAir Spa User Instructions.

Control PanelThe control panel controls all tub functions and displays useful

information such as bath temperature.

(See Fig. 2)

Inflatable Door SealAn inflatable sealing system makes the door totally watertight.

The sealing is operated by a button on the control panel

and should be activated after the door is raised. (See Fig. 3)

NOTE

When theFreedom Bath is not in use, it is best for thedoor to be left in the up (closed) position, with the sealnot inflated.

Fig. 1

Fig. 2

Fig. 3


15/48

15

Automatic DrainThe drain is automatically activated in conjunction with the

sealing system only when the door is fully raised. When the

sealing system is deactivated, the drain is open. (See Fig. 1)

Lift-Accessible ModelThe L-A model series accommodates the needs of both the

ambulatory user and those requiring lift-transfer.

Maintenance AccessThere are two openings with covers for service and cleaning

access. (See Fig. 2)

Support Strap (optional)An optional strap is available to give the resident extra security

when necessary.

There are two possible ways to fasten. (See Fig. 3)

Adjust the length by pulling the safety belt end by the clip.

Cleaning/DisinfectionOptional cleaning system is available as a separate

system, MultiClean.

EmergencyIf an emergency situation occurs when a resident is in the

bathtub, press the emergency button to open the drain and

release the door (the water will rush out around the door).

The door can now be manually pushed down.

Fig. 1

Fig. 2

Fig. 3


16/48

16

Power Assisted Door Operation

Standard1 To raise the door, press and hold the button on the con-

trol panel. The door stops automatically when end position

is reached.

2 To lower the door, press and hold the button on the

control panel. The door stops automatically when end

position is reached.

3 In an emergency situation the door may be pushed down

manually after pressing the emergency seal release button.

4 The door will not operate in power mode if any of the

following conditions exist:

The seal is ON.

The control panel is locked.

Lift Accessible, LA (optional)Integration with ArjoHuntleigh standing and raising aid lifts

such as Stedy, Sarita, Sara, Encore and Chorus is possible. The

lift accessible area under the tub is shown in the illustration.

(See Fig. 1)

1 To raise the door, press and hold the button on the con-

trol panel. The door stops automatically when end position

is achieved.

2 To lower the door, press and hold the button on thecontrol panel. The door stops automatically in a low

position. When docking with a patient lift, push the

button again and the door will proceed moving in

under the tub and automatically stops in the end position.

3 In an emergency situation the door may be pushed down

manually after pressing the emergency seal release button.

4 The door will not operate in power mode if any of the

following conditions exist:

The seal is ON.

The control panel is locked.

WARNINGTo avoid entrapment of the residents or caregiverslegs or feet, make sure that they are kept c lear of allobstacles. (See Fig. 2)

Fig. 1

1100mm43"

155mm6"

410 mm 16"

Fig. 2


17/48

17

Operating Assisted Bathing/Showering

Assisted Bathing

The Freedom Bath is also ideal for assisted bathing. All

controls are positioned for convenient use by the caregiver.

If necessary it is possible to lock the panel functions to avoid

unauthorized use. See sectionControl Panel, External Water

Supply.

Start the Bathing/Showering (7 steps)ArjoHuntleigh Liquid bathing products have been developed

for use with the Freedom Bathand are recommended.

1 Lower the door to its lowest position.

Clear all obstacles from the path of the door.

2 Help the bather to sit comfortably on the bath seat.

(See Fig. 1)

3 Bathing:

Raise the door to the top position. (See Fig. 2)

continue with the steps on the next page

WARNING

To prevent scalding, always check the watertemperature with your naked hand before directingthe water on the resident. Do note use gloves at it

may insulate to the extent that the watertemperature can be misjudged. Point the flow of thewater away from the resident.

WARNING

To avoid entrapment, make sure to keep theresidents hair, arms and feet close to the body anduse designated grab supports during anymovement.

Fig. 1

Fig. 2


18/48

18

Showering:

Raise the door but leave the door down at least an inch (25

mm) (A) from the top position to prevent the drain from

closing. (See Fig. 3)

A lower position of the door will give more convenient

access to the lower part of the bather. (See Fig. 4)

4 Momentarily press the seal/drain button and the LED

above the button will flash with a green light. When the

door seal has reached proper inflation, the compressor will

stop and a steady green light will indicate that the seal

system is activated.

5 Bathing:

Press the tub filling button and fill the tub with water

of desired temperature. (See Fig. 5)

Showering:

Press the resident shower button and shower the resident

with desired temperature.

NOTE

Do not proceed with the operation if the compressorcontinues to run for longer than 60 seconds, or starts

and stops frequently.

NOTE

To accelerate the tub filling it is possible to start filling25 seconds after pushing the seal/drain button bypushing the fill button.(The 25 second delay is electronic and the filling andshower functions are locked out until 25 seconds haselapsed since the seal button was pushed).

If equipped with optional drain pan pump, this willstart operating when the door seal is deflated. Avarying sound level is normal during the operation.

Fig. 3

1" (25 mm)

A

Fig. 4

Fig. 5


19/48

19

End the Bathing/Showering (4 steps)

1 At completion of bath, press the seal/drain button . The

drain will open and the water drains. The seal is still inflated

and showering is suitable in this position with the door up.

2 Press the seal/drain button again to deflate the seal.

During the deflating process the LED above the button willbe flashing green light.

3 See that limbs of the resident are kept out of the sealing area

and the door path.

4 Lower the door by holding the door down button

depressed.

EMERGENCY (2 steps)1 In the event of medical emergency, open the lid covering the

emergency seal release and push the button, then push down

on the door. (See Fig. 1)

2 In the event of a power failure, wait for the tub to drain

completely before activating the emergency seal release.

NOTE

If the bather has both of their feet in contact with bothof the water sensors at the same time, the seal maynot deflate.

NOTE

The emergency seal release should only be used inemergency, because the water will spill out onto thebathroom floor.

Fig. 1EMERGENCY


20/48

20

Air Spa Operation (optional)

Check Before Usage: The door is fully raised.

The tub is filled above the high water level sensor button.

1 Press the Air spa ON/OFF button on the display and the air

blower will start in maximum speed. The blower will stop

by pressing the ON/OFF button again.

2 The intensity of the air spa bubbling action can be reducedby pressing and holding-in the blower speed control symbol

on the display. Release the button when the desired intensity

is reached. The blower speed can be changed at any time.

3 After completing the air spa, wash & shampoo or drain the

tub if bathing is complete.

4 Press the seal/drain button to open the drain. Allow the

water to drain below the low water level sensor buttons.

Once again press the seal/drain button and the seal will

deflate and the door can be lowered.

5 Clean/disinfect the tub. See section Cleaning andDisinfection Instructions.

6 Model A (without MultiClean): 20 minutes after the tub is

emptied, the air-blower activates for 1 minute.

Model B: The button ON/OFF has to be pushed to start the

blower, which then will activate for 1 minute.

NOTE

Only use emulsifying mineral oil.Operating the air blower with soapy water in the tubis not recommended, as foaming of the bath water islikely to occur. Use clean water whenever possible.

NOTEThe blower cannot be stopped during the 1-minute

dry cycle, but the speed can be controlled duringthis time.

If the bather has both of their feet in contact with bothof the water sensors at the same time, the seal maynot deflate.


21/48

21

Waste Water Pan

The drain pan is placed on the right hand side of the Freedom

Bath.

Placed in position shown in figure below it will collect spilt /waste water.

Placed in position upside down as shown in figure below it will

lead spilt water from Freedom Bathonto the floor.

NOTE

The water in the drain pan may be contaminated.Use caution when emptying.


22/48

22

Home Care Use

For Distr ibutors and RentersWhen transportingFreedom Bath to the customer

with a van:

Make sure the bathis properly secured duringtransport.

When delivering theFreedom Bath make sure

that:

The requirements according to the site preparation

instructions prior to installation are followed:

Material: The floor should be made of a

slip-resistant material, free of bumps.

Floor slope: When using a floor drain, the

slope towards the drain should not exceed 1:50.

Floor Attachments: The floor construction mustbe suitable for anchoring the bolts.

The bath is installed according to theAssembly

and Installation Instructionby qualified

personnel.

Make sure:

The thermostatic mixer has been calibrated

according to theAssembly and Installation

Instructionsby an ArjoHuntleigh service

technician.

You read thisIFUtogether with the receiver

(including relatives and caregivers).

Show the features and intended usage described in

theIFU with help of the real product.

Read all the warnings to the receiver.

The user has understood the cleaning and

disinfection instructions.

Perform a functionality test according to Care and

Preventive Maintenance in thisIFU.

The environment fulfils all the requirements

described in thisIFU.

WARNINGTo prevent scalding, make sure that thewater mixer has been calibrated. Confi rm

that responsible organization hasestablished calibration routines.

Using the Freedom BathBefore usingFreedom Bathin home environment

make sure that:

All caregivers, including relatives, have read andunderstood the instructions in thisIFU.

The space requirements for the bath are followed.

(See Fig. 1)

When theFreedom Bath is not in use make sure

that:

No children can access the bath.

No pets can come in contact with the bath.

The storage environment fulfils the requirements

specified under Technical Specificationsin this

IFU.

WARNINGTo avoid st rangulation, make sure to never

leave children unattended near theequipment.


23/48

23

Space requirements around the bath

Freedom Bathmust always be installed according to

recommended space requirements, this to provide optimal

working conditions for personnel and resident.

Available area for li ft integrationFreedom Bath in lift accessible version (LA) allows following area

for lift integration, limited by the drain connections.

NOTES

Fig. 1


24/48

24

Cleaning and Disinfection Instructions

DisinfectionThorough disinfection routines are necessary tostop the build-up of bacteria on and in theequipment.

This is particularly vital in cases where theFreedom Bathis a shared facility. Effectivedisinfection as outlined below reduces the riskof cross-infection between residents.

Only use ArjoHuntleigh branded disinfectantcleansers (e.g. Arjo Clean).

If you have any questions regarding disinfecting the

Freedom Bath, or wish to order disinfectant fluid,

contact ArjoHuntleigh Customer Service. See section,

Parts and Accessories.

Make sure to have the Material Safety Data Sheets

(MSDS) available for the disinfectant being used.

WARNING

To avoid eye and skin damage, always useprotective glasses and protective gloves.If contact occurs, rinse with plenty of water.If eyes or skin become irritated, consul t aphysician. Always read theInstructions forUse and Material Safety Data Sheet of thedisinfectant.

WARNINGTo prevent cross-contamination, alwaysfollow the disinfection instructions in thisInstructions for Use.

WARNINGTo avoid eye or skin irr itation, neverdisinfect in the presence of a resident.

Al lowed Disinfectants Arjo Clean

Arjo General Purpose Disinfectant

Arjo Disinfectant Cleanser IV

Arjo All Purpose Disinfectant

(not for MultiClean)

Arjo CenKleen IV

Accessories for Dis infecting theFreedom Bath

Protective gloves

Protective glasses

Spray bottle with cleaning fluid (detergent and

disinfectant) or disinfection spray handle with

cleaning fluid (detergent and disinfectant)

Spray bottle with water or shower handle with

water

Cloths - wet and dry

Disposable towels

Soft bristle brush

Long handled soft bristled brush

CAUTION

To avoid damage on the equipment only

use ArjoHuntleigh branded d isinfectants.


25/48

25

Always Follow these 25 Steps forProper Cleaning and Disinfection.

Removing v isual residue (Step 1-4 of 25)

1 Put on protective gloves and eye wear.

2 Open the drain to empty any left over water.

3 Detach and place the head cushion (if applicable)

and support strap on the bottom of the bathtub.

4 Shower and rinse the bath, head cushion and

support strap with water to remove visible

residue. Turn the head cushion and support strap

and rinse again.

Cleaning (Step 5-12 of 25)

5 Close the drain by raising the door to top position.

6 Spray disinfectanton all internal bath surfaces, the

head cushion and support strap at the bottom of the

tub. Turn the head cushion and support strapand

spray on the other side. Pay attention to parts, knobsand sensors attached to the bath surface such as

safety belt knobs and surface overflow outlet.

7 Scrub all the surfaces of bath, the head cushion and

support strapwith a soft bristle brush or cloth (to

remove any deposits e.g. skin flakes).

8 Open the drain by pressing the door seal/drain

button.

9 Use the shower handle and rinse all parts clean

with water (temperature approximately 25 C) to

remove the disinfectant.

10 Soak a cloth in disinfectant.

11 Wipe all other contact areas such as the outside of

the bath (particularly behind the head).

12 Wet a new cloth with water and remove all traces of

the disinfectant on contact areas.

Disinfection (Step 13-22 of 25)

13 Use a spray bottle and spray disinfectant in the

drain.

14 Close the drain.

15 Spray disinfectant on all internal bath surfaces, the

head cushion and support strap at the bottom of

the tub. Turn the head cushion and support strap

and spray on the other side. Pay attention to parts,knobs and sensors attached to the bath surface such

as safety belt knobs and surface overflow outlet.

16 Allow an appropriate contact time of the

disinfectant according to the instructions on the

disinfectant bottle.

17 Open the drain.

18 Rinse all parts clean with water (temperature

approximately 25 C). Use the shower handle to

remove cleaning fluid.

19 Soak a cloth in disinfectant.

20 Wipe all other contact areas such as the outside of

the bath (particularly behind the head).

21 Allow to stand for 10 minutes.

22 Wet a new cloth with water and remove all traces

of cleaning fluid on contact areas.

Drying (Step 23-25 of 25)

23 Dry each part of the Freedom bath with a clean

dry cloth.24 The door should be left in top position when the

tub is idle.

25 Leave to air dry.


26/48

26

Disinfecting the Air Spa UsingMultiClean (32 Steps)

Cleaning (Step 1-16 of 32)

1 Put on protective gloves and eye wear.

2 Check the level of the disinfectant in the

MultiClean.

3 Lift out the spray handle from theMultiClean

disinfection system and hold it over the bath tub.

4 Turn the ON/OFF control on theMultiClean to

the ON position. Turn the function selection

control to the disinfection setting (yellow).

5 Place the disinfection spray handle into the

disinfectant/rinsing ferrule and turn either way to

secure it (some force may be needed).

6 Press the trigger handle and hold it until the

disinfectant agent flows from allAir Spanozzles.

7 Let it run for 10 seconds.

8 Remove the disinfection spray handle from the

disinfectant/rinsing inlet.

9 Turn theMultiCleancontrol to the OFF position.

10 Place the disinfection spray handle in its holder.

11 Place the water spray handle into the disinfectant/

rinsing inlet and turn either way to secure it (some

force may be needed).

12 Press the trigger handle and hold it until clean

water flows from all nozzles.13 Let it run for another 30 seconds.

14 Remove the shower handle from the disinfectant/

rinsing inlet.

15 Rinse the bath.

16 Place the spray handle back into the holder on the

MultiCleanand turn the unit off.

Disinfection (Step 17-31 of 32)

17 Lift out the spray handle from theMultiClean

disinfection system and hold it over the bath tub.

18 Turn the ON/OFF control on theMultiClean to the

ON position. Turn the function selection control

to the disinfection setting (yellow).

19 Place the disinfection spray handle into the

disinfectant/rinsing inlet and turn either way tosecure it (some force may be needed).

20 Press the trigger handle and hold it until the

disinfectant agent flows from allAir Spanozzles.

21 Let it run for 10 seconds.

22 Remove the disinfection spray handle from the

disinfectant/rinsing inlet.

23 Turn theMultiCleancontrol to the OFF position.

24 Place the disinfection spray handle in its holder.

25 Allow an appropriate contact time of the

disinfectant according to the instructions on the

disinfectant bottle.

26 Place the water spray handle into the disinfectant/

rinsing inlet and turn either way to secure it (someforce may be needed).

27 Press the trigger handle and hold it until clean

water flows from all nozzles.

28 Let it run for another 30 seconds.

29 Remove the shower handle from the disinfectant/

rinsing inlet.

30 Rinse the bath.

31 Place the spray handle back into the holder on the

MultiCleanand turn the unit off.

Drying (Step 32 of 32)

32 Press the button ON/OFF to start the air-blower,

which then will be activated for 1 minute.

NOTE

Disinfection should be distributed throughallAir Spanozzles, or proper disinfectioncan not be guaranteed. Contact an Arjo-

Huntleigh technician if that problem occurs.

NOTEThe blower cannot be stopped during the1-minute dry cycle, but the speed can becontrolled during this time. If the bather hasboth of their feet in contact with both of the

water sensors at the same time, the seal maynot deflate.


27/48

27

Microbiological Formation PreventionIn order to enhance the on-site curative actions (chlorine or

thermal shock), which do not guarantee a reduction of the

contamination long term, make sure to follow the instructions

below.

Do not forget to contact ArjoHuntleigh for the annual Preventive

Maintenance visit.

Installation precautions

In order to limit the growth of bacterial flora, it is necessary

to take action at four levels: Avoid stagnating water and make sure proper water

circulation;

Take precautions against the formation of scale andcorrosion based on the water quality;

Maintain a high water temperature all the way fromthe hot water dispenser to the different distributionpipes;

Mix hot and cold water as close as possible to thepoint of use.

Use

Make sure that the water circulates in the bath andthe shower on a daily basis even if the bath tub is notused; and particular to make sure to remove anywater that may be left behind in the hose.

Let the water flow approximately 5 minutes before the

first bath of the day. Clean and disinfect the bath tub according to the IFU

before the first bath of the day and after the bath ofeach resident.


28/48

28

Care and Preventive Maintenance

The Freedom Bathis subject to wear and tear, and the following actions must be performed when specified to

make sure that the product remains within its original manufacturing specification.

Preventive Maintenance Schedule: Freedom

WARNINGTo avoid malfunction resulting in injury, make sure to conduct regular inspections and followthe recommended maintenance schedule. In some cases due to heavy use of the product andexposure to aggressive environment more frequent inspections should be carried out. Localregulations and standards may be more stringent than the recommended maintenanceschedule.

CAREGIVER OBLIGATIONS Action/Check Every DAY Every

WEEK

Every

MONTH

Every 2:nd

YEARDisinfect X

Visually check all exposed parts X

Check door seal X

Visually check hoses, pipes and connections X

Perform functionality test X

Empty and clean pan under tub X

Visually check the support strap, if any X

Exercise the thermostat mixer XCheck/clean filters, incoming water X

Replace the safety strap X

WARNINGTo avoid injury to both resident and caregiver, never modify the equipment or useincompatible parts.


29/48

29

Caregiver ObligationsCaregiver obligations shall be carried out by personnel withsufficient Freedom Bathknowledge following the instructionsin thisIFU.

Daily

Disinfect. Freedom Bathhas to be cleaned immediately

after use. Standard disinfection agents and shampoos should

be used in recommended concentrations. Clean door strip/seal and under the tub:

Instruction for non lift accessible version of Freedom Bathonly: To make area at lower part of the door and under tubaccessible for cleaning, perform following procedure:(See Fig. 1-2)

1 Hold the door up and door down buttons pressed

simultaneously for 30 seconds, until the temperature display

starts flashing.

2 Press the door down button. The door will move under

the tub, leaving the lower part of the strip/seal and the area

under the tub free for cleaning. Take caution at this

operation as the crush protection is off. The protection is

automatically activated again after one minute.

Weekly Visually check all exposed parts.Make sure no cracks or

sharp edges could cause the resident or caregiver injury.

Check door seal:Check the seal for cracks or other

damage. Check along the complete length that it is not

twisted, shown as (B) in the illustration. Correct placementis shown as (A). (See Fig. 3)

WARNINGTo avoid injury, only use the emergencylowering when normal lowering is impossible.Use extreme care during lowering.

CAUTION

To avoid damage on the equipment on ly useAr joHuntleigh branded dis in fectants.

Fig. 1

Fig. 2

Fig. 3

A B


30/48

30

Visually check hoses, pipes and connections:

Remove the left and right cover by removing the screws and

lifting the covers upwards. Visually inspect for leaks of any

kind on hoses, pipes, connection and drain. (See Fig. 4)

Perform functionality test:Test all panel functions and

disinfection options. With water on: check shower hose and

shower handle for damage - replace if defect. Empty and clean accumulated water and dirt from the

drain pan under the tub:

Clean the suction filter from dirt and/or lime build up on the

surface of the net.

Visually check the support strap.Check the complete

length for fraying, cuts, crack, tears, that no inner fabric is

showing and that no other damage is visible. If the strap is

found damaged, replace it.

Monthly Check/clean filters incoming water (with mixer):

A rinsing valve with a filter is mounted on each of the

two water supply hoses found under the left front cover.

The filter should be rinsed in both valves as follows:

1 Remove the left cover by removing the screws and lifting it

upwards. (See Fig. 4)

2 Close the valves. The handles (red for hot water and blue for

cold) should be in a cross position

(See Fig. 5).

3 Remove the cap (A)with a wrench. (See Fig. 5)

4 Pull out the filter (B)and clean it carefully in water.

(See Fig. 5)5 Reassemble the filter.

6 Fit the cap.

Exercise the thermostat mixer:

Turn the temperature control knob back and forth over the

whole temperature range. This is particularly important in

areas with hard water. (See Fig. 6)

Yearly

Freedom Bath must be serviced according to thePreventive Maintenance Schedule (Qualified Personnel Action/

Check).

WARNINGPressurised system and risk of scalding. Makesure that the valve (A) is closed before removingthe cap, this is especially important for the hotwater valve.

Fig. 4

Fig. 5

B

A

Fig. 6


31/48

31

WARNINGTo avoid injury and/or unsafe product, the maintenance activities must be carried out at thecorrect frequency by qualified personnel using correct tools, parts and knowledge ofprocedure. Qualified personnel must have documented training in maintenance of this device.

QUALIFIED PERSONNEL Action/Check EveryYEAR

Every3:rd

YEAR

Every5:th

YEAR

Check/adjust mixer including seal kit/complete thermostatic unit X

Check/clean filters, incoming water X

Check valves and membranes replace if necessary X

Check/replace seal kit or complete shower handle X

Lubricate moving parts XCheck the emergency seal release valve X

Check hoses and connections for leaks and damage X

Check all vital parts for corrosion and damage X

Perform full feature functionality test X

Check mechanical attachments X

Check that latest updates have been implemented X

Check the earth wiring connections X

Check door protection (only lift accessible) X

Check door system X

Replace filter, air-blower (Air spa) X

Replace air jet diaphragm (Air spa with MultiClean) X

Replace all pressurized hoses X

NOTE

Optimum performance and safety in operation are made sure by careful daily use of the equipmentaccording to the instructions. Early identification of any damage by routine weekly checks, andannual maintenance. Following these procedures correctly will also help to maximize the FreedomBaths service lifetime.


32/48

32

Troubleshooting

NOTE

If the product does not work as intended, immediately contact your local ArjoHuntleigh representative

for support.

PROBLEM (using the Freedom Bath) ACTION

In the event of power failure during bath.

1 The tub drain is opened automatically.

2 The door can be manually pushed down by pushing the

emergency button.

Nothing happens when pressing a button on thepanel. Function lock is activated Red LED forfunction lock is on.

Release the function lock by pressing the 2 buttons DOOR

UP and DOOR DOWN at the same time for 1 second.

It is not possible to stop a function by pressing abutton.

Wait for one minute. The Air Spa is in the dry cycle(option).

Air Spa stops during operation (option).

1 Normal, if used more than 15 minutes.

2 If used less than 15 minutes it may be overheated due to

high ambient temperature or clogged filter. Can be

started when cooled off.

3 Power failure.

Water from shower and filling spout is slow.

1 In order to feel if any hot water is coming in feel theincoming hot water line to see if hot.

2 Check and clean filter for incoming water according to

section Care and Preventive Maintenance.

Auto fill function will not stop filling afterreaching high water level sensor.

Metal sensor plugs need cleaning because of collected buildup. See section Cleaning and Disinfection Instructions.


33/48

33

Intentionally left blank


34/48

34

Technical Specifications

General

Dimensions exterior 1510 x 760 x 1045 mm (59 1/2 x 29 3/4 x 41 1/8)

Dimensions seat 480 x 480 mm (18 7/8 x 18 7/8)

Colour White

Weight - still bath 130 kg (286 Ibs)

Weight with air spa 140 kg (308 Ibs)

Tub volume (with resident) approx. 320 litres

Drain flow rate 130 l/min

Drain flow rate with water trap 110 l/min

Sound level 66 - 79,5dBA

Max. ambient temperature 40 C (104 F)Pollution degree 2

SWL (Safe Working Load) (resident + water) 550 kg (1212 lbs)

Max. patient weight 160 kg (353 lbs)

Range of thermometer display 10-50 C (50-122 F)

Accuracy of thermometer display +/-1 C (1,8 F)

Precision of displayed value 1 C (1,8 F)

Max. floor load 675kg / 0,6 m2

Max. floor pressure 0,6 N/mm2

Degree of protection IPX4IP: Ingress ProtectionX: The protection against contact and ingress ofobjects is not specified for this product.4: Water splashing against the product from anydirection does not effect safety or essentialperformance

Operating Conditions

Temperature 10C (50F) to 40C (104F)

Humidity (Relative) Max 90% at 20C (68F)

Atmosperic pressure range 700-1060 hPa

Transport and Storage Conditions

Temperature -20C (-4F) to 70C (158 F)

Humidity (Relative) 80% at 20C (68F)

Atmosperic pressure 500-1100 hPa


35/48

35

NOTE

All drainage, water and electrical installation work should be carried out by qualified personnel, inaccordance with local and national regulations.

Electric Supply

Voltage230/240 V, single phase120 V (US)

Frequency 50 Hz

Fuse T 6.3 AL

Ground Fault Circuit Interrupter(not included in delivery) 10 mA

The unit must be continuously powered and connected via a ground fault circuit interrupter.

The unit must be connected to protective earth (PE).

Power supply cord Replaced by qualified personnel

Water Supply

Cold/warm water connections, inlets and outlets 3/4

CW temperature 2-20 C (36-68 F)

WW temperature 60-80 C (140-176 F)

Drainage

Tub drain 1 1/2

Floor drain recommended to accommodate emergency user evacuation.

WARNINGTo avoid electric shock, make sure that the equipment is connected to: Continuously powered supply mains with protective earth. Separate fuse and ground fault circuit interrupter (GFCI) A mains disconnection device Equipotential bonding point

Al l instal lat ions must be in accordance with local codes and regulations.

Mains Disconnection Device

Permanently installed in wall. Visible and accessible at all times

Mains transient voltage 4kV*

Creepage distance 3 mm*

Air clearance 1,8 mm*

Direction of movement Up and down, right and left,clockwise and counterclockwise

* If local regulations are higher, they must be met.


36/48

36

Allowed Product CompatibilityFreedom Bath integrates with the followingArjoHuntleigh products:

Stedy, Sara Stedy, Sara Light, Sara Plus, Sara 3000and MultiClean

No other combinations are allowed

RecyclingThe device should be recycled according to national regulations

Package Wood, corrugated cardboard and plastic arerecyclable

The bath Electric, steel and plastic parts shall be separated andrecycled according to WEEE.

Disposal of the Freedom Bath

Bathtub The device is marked with the WEEE symbol to indi-cate that it is electronic equipment covered by theDirective 2002/96/EC on waste electrical and elec-tronic equipment. In European countries the crossedout wheeled-bin WEEE symbol reminds you that allthe electrical and electronic products, batteries andaccumulators must be taken to separate collection atend of their working life. This requirement applies inthe European Union. Do not dispose these productsas unsorted municipal waste. You can return yourdevice and accessories to ArjoHuntleigh or you cancontact your local authorities for advice on disposal.


37/48

37



38/48

38

Labels on the Freedom Bath

On the labels you will find the following

information:

Plumbing Approval

Supply voltage 230-240 V~50Hz (EU)

120 V~60Hz (US)VA Max power

IPX 4 Protection class against splashingwater

Class I Connected to protective earth

Type B, Applied part:protection against electrical shockin accordance with EN/IEC60601-1.

Read theIFUbefore use

Separate electrical and electroniccomponents for recycling inaccordance with the EuropeanDirective 2002/96/EG (WEEE)

ANSI Z124.1.2-2005

Plastic Bathtub and Shower Units

ANSI/ASMEA112.19.7M-1995

Whirlpool Bathtub Appliances

ANSI/ASMEA112.19.8-1987

Suction Fittings

ANSI/ASSE1001-1988

Pipe Applied Vacuum Breakers

ANSI/ASSE1014-1989 Hand- Held Showers

ANSI/ASSE1016-1996

Individual Thermostatic, Pres-sure Balancing and CombinationPressure Balancing and Thermo-static Control Valves for Individ-ual Fixtures

CAN/CSAC22.2

No.601.1-M90

Medical Equipment with respectto electrical shock,fire and mechanical hazards onlyin accordance with Standards no.UL60601-1

CAN/CSA-B45.0-2004 andB45.5-2004

Patient bathing units

CE marking (EU-models 230/240V - 50 Hz)

WRAS (GB only)

WRAS approved Thermostatic Mixing Valves,

according to National Health Service.

Model Engineering Specification D 08- TMV3.

Thermostatic Mixing Valves (Health care Premises).

Designation Code: HP-S / HP-T44.

Warning labelsStates the actual warnings and cautions for the

product.

Identif ication labelThe identification label states the type of equipment

and serial number (see figure).

Water connection labelRequired max. and min. temperature for cold and hot

water and max./min. water pressure.

Attention labelAttention label placed on the button for activation of

the emergency seal release valve.

CAN/CSA-B64.0-1994 andB64.1.1-1994

Plumbing Fixtures, BackflowPreventers and Vacuum Breakers

CE marking in accordance with theMedical Devices Directive 93/42/EEC.

The equipment has been EMC-testedand fulfils all requirements accordingto IEC 60601-1-2. Electric safetyaccording to EN/IEC 60601-1. Referto Notified Body: BSI.

UL marking (US-models 120V-60Hz)Medical Equipment with respect toelectrical shock, fire and mechanical

hazards only in accordance withStandards no. UL 60601-1 CAN/CSA-C22.2 No.601.1-M90

4ML5 Certificate control number for UL

CLA

SSIFIED

S


39/48

39

WARNING

Disconnect electrical

power before servicing

WARNINGRisk of fire -replace fuse as marked

CAUTION

To reduce risk of electricalshock do not remove the lid.Refer to qualified

service personnel

COLD HOTFROIDE CHAUDEKALT WARM

MIN 300 kPa (44 psi)

MAX 600 kPa (87 psi)MIN 200 kPa (29 psi)

MAX 600 kPa (87 psi)

MAX 25C (77F)MIN 38C (100F)

MAX 80C (175F)

8418363

ArjoHuntleigh ABVerkstadsvgen 5241 38 Eslv, SWEDENMade in Sweden

Read the operating instructions before useMerci de prendre connaissance de la notice d'utilisationLesen Sie bitte die bedienungs-anleitung durch

MODEL: AFXXXXX-XXFreedom Bath

8418539E

120 V ~60HzMax 1100 VAIPX 4

Class I

Mode of operation:Air spa:

ED max 50%15 min on / 15 min off

Door opening:ED max 10%

SWL Safe Working Load

550 kg / 1213 lbsMax Total Load550 kg/ 1213 lbs

Max Patient Weight

160 kg / 350 lbs

8418675D

CAN/CSA - C22.2 No. 601.1-M90

UL60601-1and

4ML5

MEDICAL EQUIPMENT

PATIENT BATHING UNIT

IN ACCORDANCE WITH

ANSI Z124.1-1995

ANSI/ASME A112.19.7M-1995

ANSI/ASME A112.19.8M-1987

ANSI/ASSE 1014-1989

ANSI/ASSE 1016-1996

CAN/CSA B45.5 and B45.5-02

CAN/CSA B64.0 and B64.1.1-01

CAN/CSA B64.0 and B64.8-01

Example of

Water connection label

Warning label

Data label EU

Approval label

Address label

Bonding lug

Connect incoming electrical service

See installation manual for instructions

8418372

Warning label

Field wiring box

SEE0102001

Example ofidentification label

Manufacturing Year Week

Serialnumber

countrySE=Sweden

Manufacturing

worksE=Eslv

Product no

Serial no

AFA XXXX

SEE0102001

Made by Arjo in Eslov, Sweden

010115

ArjoHuntleigh ABVerkstadsvgen 5241 38 Eslv, SWEDENMade in Sweden

Read the operating instructions before useMerci de prendre connaissance de la notice d'utilisationLesen Sie bitte die bedienungs-anleitung durch

MODEL: AFXXXXX-XXFreedom Bath

8418538D

230-240 V ~50HzMax 1100 VAIPX 4

Class I

Mode of operation:Air spa:

ED max 50%15 min on / 15 min off

Door opening:ED max 10%

SWL Safe Working Load

550 kg / 1213 lbsMax Total Load550 kg/ 1213 lbs

Max Patient Weight160 kg / 350 lbs

Data label US

Calibration label located

on control panel before

irst use

Applied Part

Attention label

WARNING!

Do not use before calibration.

FR

AVERTISSEMENT!Ne pas utiliser avant calibration.

DEWARNUNG!Vor der Kalibrierung nicht benutzen.

NL

WAARSCHUWING!Niet gebruiken vr kalibreren.

ITAVVERTENZA!Non utilizzare prima della taratura.

ESADVERTENCIA!No utilizar antes de la calibracin.

PL

UWAGA!Nie uywa przed przeprowadzeniem kalibracji.

8418722A


40/48

40

Approvals and List of Standards

CERTIFICATE STANDARDS

EN/ISO/IEC/UL 60601-1 Medical electrical equipment

Part 1: General requirements for basic safety and essentialperformance.

EN 60601-1-2 Electromagnetic Compatibility -Requirements and Tests

EN 60601-1-11 Requirements for medicial electrical equipment and medicalelectrical systems used in the home healthcare environment.

CAN/CSA-C22.2 No. 601.1 Medical equipment Certified for Canada

ANSI Z124. 1-1995 Standards for Plastic Bath Tub Units

ANSI/ASSE 1014-1989 Handheld Shower ANSI/ASSE 1016-2005 Individual Thermostatic, Pressure Balancing and Combination

Pressure Balancing and Thermostatic Control Valves forIndividual Fixtures.


41/48

41



42/48

42

Electromagnetic Compatibili ty

Medical electrical equipment needs special precautions regarding EMC (Electromagnetic compatibility) and

needs to be used according to the EMC information below.

Portable and mobile RF communications equipment can affect Freedom Bath.

WARNINGStacking or placing other electrical equipment next to this device is not recommended, it caninterfere with the equipments operation and safety. Portable and mobile radio-frequency (RF)communications equipment can interfere with th is equipment operation and safety.

WARNING

The equipment may cause radio interference or may disrupt the operation of nearbyequipment.It may be necessary to take action, such as reorienting, relocating the equipment or shieldingthe location.

Guidance and manufacturers declaration electromagnetic emissions

The Freedom Bathis intended for use in the electromagnetic environment specified below. The customer or

the user of the Freedom Bathshould assure that it is used in such an environment.

Emissions test Compliance Electromagnetic environment guidance

RF emissions

CISPR 11

Group 1 Freedom Bathuses RF energy only for its internal

function. Therefore, its RF emissions are very low and

are not likely to cause any interference in nearby

electronic equipment.

RF emissions

CISPR 11

Class B Freedom Bathis suitable for use in all establishments,

including domestic establishments and those directly

connected to the public low-voltage power supplynetwork that supplies buildings used for domestic

purposes.Harmonic emission

IEC 61000-3-2

Class A

Voltage fluctuations/flicker

emission

IEC 61000-3-3

Complies


43/48

43

Lift-functions, tilt-functions and temperature measurement were determined to be Essential Performance.

Guidance and manufacturers declaration electromagnetic immunity

The Freedom Bath is intended for use in the electromagnetic environment specified below. The customer or

the user of the Freedom Bathshould assure that it is used in such an environment.

Immunity test IEC 60601test level

Compliance level Electromagneticenvironment guidance

Electrostatic

discharge (ESD)

IEC 61000-4-2

6 kV contact 8 kV air

6 kV contact 8 kV air

Floors should be wood, concrete or

ceramic tile. If floors are covered

with synthetic material, the relative

humidity should be at least 30%.

Electrical fast

transient/burs

IEC 61000-4-4

2 kV for power

supply lines

1 kV forinput/output lines

2 kV for power

supply lines

input/output lines not

applicable

Mains power quality should be that

of a typical commercialor hospital environment.

Surge

IEC 61000-4-5

1 kV line(s) to line(s)

2 kV line(s) to earth

1 kV line(s) to line(s)

2 kV line(s) to earth



Voltage dips,

short

interruptions

and

voltage

variationson power supply

input lines

IEC 61000-4-11

95% dip in UT)

for 0,5 cycle

40% UT

(60% dip in UT)

for 5 cycles

70% UT

(30% dip in UT)

for 25 cycles

95% dip in UT)

for 5 s

95% dip in UT)for 0,5

cycle

40% UT

(60% dip in UT) for 5

cycles

70% UT

(30% dip in UT) for 25

cycles

95% dip in UT) for 5s



Power

frequency

(50/60Hz)

Magnetic fieldIEC 61000-4-8

3 A/m 3 A/m

Power frequency magnetic fields

should be at levels

characteristic of a typical location

in a typical commercial or hospital

environment.

NOTE UTis the a.c. mains voltage prior to application of the test level


44/48

44

Guidance and manufacturers declaration electromagnetic immunity

Freedom Bathis intended for use in the electromagnetic environment specified below. The customeror the user of Freedom Bathshould assure that it is used in such an environment.

Immunity test IEC 60601test level

Compli-ance level Electromagnetic environment guidance

Conducted RFIEC 61000-4-6

Radiated RFIEC 61000-4-3

3 Vrms150 kHz to

80 MHz

3 V/m80 MHz to

2.5 GHz

10 Vrms

3 V/m

Portable and mobile RF communications equipment

should be used no closer to any part of Freedom Bath,

including cables, than the recommended separation

distance calculated from the equation applicable to the

frequency of the transmitter.

Recommended separation distanced=0,35P

d=1,2P 80 MHz to 800 MHz

d=2,3P 800 MHz to 2.5 GHz

Where P is the maximum output power rating of the

transmitters in watts (W) according to the transmitter

manufacturer and d is the recommended separation

distance in metres (m).

Field strengths from fixed RF transmitters, as determined

by an electromagnetic site survey, ashould be less than

the compliance level in each frequency range. b

Interference may occur in the vicinity of equipment

marked with the following symbol:

NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies.

NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by

absorption and reflection from structures, objects and people.

a Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land

mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically

with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic

site survey should be considered. If the measured field strength in the location in which Freedom Bathis used

exceeds the applicable RF compliance level above, the Freedom Bathshould be observed to verify normal

operation. If abnormal performance is observed, additional measures may be necessary, such as re-orienting or

relocating the Freedom Bath.

b Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 10 V/m.


45/48

45

Recommended separation distances between portable and mobile RF communicationsequipment and Freedom Bath

Freedom Bathis intended for use in an electromagnetic environment in which radiated RF disturbances are

controlled. The customer or the user of Freedom Bathcan help prevent electromagnetic interference by

maintaining a minimum distance between portable and mobile RF communications equipment (transmitters)

and theFreedom Bathas recommended below, according to the maximum output power of thecommunications equipment

0,01

0,1

1

10

100

0,04

0,11

0,35

1,1

3,5

0,12

0,38

1,2

3,8

12

0,23

0,73

2,3

7,3

23

For transmitter rated at a maximum output power not listed above, the recommended separation distance d in

metres (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the

maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer.

NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.

NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by

absorption and reflection from structures, objects and people.


46/48

46

Parts and Accessories

Support strapFor Disinfectant contactyour local representative


47/48

AUSTRALIAArjoHuntleigh Pty Ltd78, Forsyth streetOConnorAU-6163 Western AustraliaTel: +61 89337 4111Free: +1 800 072 040

Fax: + 61 89337 9077

BELGIQUE / BELGIArjoHuntleigh NV/SAEvenbroekveld 16B-9420 ERPE-MERETl/Tel: +32 (0) 53 60 73 80Fax: +32 (0) 53 60 73 81E-mail: [email protected] Matheson Boulevard WestSuite 300MISSISSAUGA, ON, L5R 3R3

Tel/Tl: +1 905 238 7880Free: +1 800 665 4831 InstitutionalFree: +1 800 868 0441 Home CareFax: +1 905 238 7881E-mail: [email protected]

ESK REPUBLIKAArjoHuntleigh s.r.o.Hlinky 118CZ- 603 00 BRNOTel: +420 549 254 252Fax: +420 541 213 550

DANMARKArjoHuntleigh A/S

Vassingerdvej 52DK-3540 LYNGETel: +45 49 13 84 86Fax: +45 49 13 84 87E-mail: [email protected]

DEUTSCHLANDArjoHuntleigh GmbHPeter-Sander-Strasse 10D-55252 MAINZ-KASTELTel: +49 (0) 6134 186 0Fax: +49 (0) 6134 186 160E-mail: [email protected]

C. Psimitis Co LtdDimitriou Andr. 59GR-16121 KAISARIANI ATTIKIS: 21 0724 36 68: 21 0721 55 53

ESPAAArjoHuntleigh Ibrica S.L.Ctra. de Rub, 88 1 planta - A108173 Sant Cugat del VallsES- BARCELONA 08173Tel: +34 93 583 11 20Fax: +34 93 583 11 22E-mail: [email protected]

FAR EASTARJO Far East LimitedUnit 3A, 4/F., block B Hoi Luen

Industrial Centre

55 Hoi Yuen Road,Kwun Tong, KowloonHONG KONG

Tel: +852 2508 9553Fax: +852 2508 1416

FRANCEArjoHuntleigh SAS2 Avenue Alcide de GasperiCS 7013359436 RONCQ CEDEXTl: +33 (0) 3 20 28 13 13Fax: +33 (0) 3 20 28 13 14E-mail : [email protected]

INTERNATIONALArjoHuntleigh International Ltd.ArjoHuntleigh House

Houghton Hall ParkHoughton RegisUK-DUNSTABLE LU5 5XFTel: +44 (0) 1582 745 800Fax: +44 (0) 1582 745 866E-mail:[email protected]

ITALIAArjoHuntleigh S.p.A.Via di Tor Vergata 43200133 ROMA - ITALIATel: +39 (0) 6 87426211Fax: +39 (0) 6 87426222E-mail: [email protected]

NEDERLANDArjoHuntleigh Nederland BVBiezenwei 214004 MB TIELPostbus 61164000 HC TIELTel: +31 (0) 344 64 08 00Fax: +31 (0) 344 64 08 85E-mail: [email protected]

NEW ZEALANDArjoHuntleigh Ltd41 Vestey DriveMount WellingtonAUCKLAND 1060Tel: +64 (0) 9 573 5344Free Call: 0800 000 151Fax: +64 (0) 9 573 5384E-mail: [email protected]

NORGEArjoHuntleigh Norway ASRyenstubben 2NO-0679 OSLOTel: +47 22 08 00 50Faks: +47 22 08 00 51E-mail: [email protected]

POLSKAArjoHuntleigh Polska Sp. z o.o.ul. Ks Piotra Wawrzyniaka 2PL 62-052 KOMORNIKI (Poznan)Tel: +48 61 662 15 50Fax: +48 61 662 15 90E-mail: [email protected]

PORTUGALArjoHuntleigh em Portugal:MAQUET Portugal, Lda. (Distribudor Exclusivo)Rua Poeta Bocage n. 2 - 2G1600-233 Lisboa, PortugalTel: +351 214 189 815Fax: +351 214 177 413E-mail: [email protected]

SUISSE / SCHWEIZArjoHuntleigh AGFabrikstrasse 8Postfach4614 Hgendorf,

Tl/Tel: +41 (0) 61 337 97 77Fax: +41 (0) 61 311 97 42

SUOMIArjoHuntleigh OYVanha Porvoontie 229FI-01380 VANTAAPuh: +358 9 4730 4320Faksi: +358 9 4730 4999

SVERIGEARJO Scandinavia ABVerkstadsvgen 5Box 61

SE-241 21 ESLVTel: +46 (0) 10-335 45 00Fax: +46 (0) 413-138 76E-mail: [email protected]

UNITED KINGDOMArjoHuntleigh UKArjoHuntleigh HouseHoughton Hall ParkHoughton RegisUK-DUNSTABLE LU5 5XFTel: +44 (0) 1582 745 700Fax: +44 (0) 1582 745 745E-mail:[email protected]

USAArjoHuntleigh Inc.2349 W Lake Street Suite 250Addison, IL 60101Tel: +1 630 307 2756Free: +1 800 323 1245 InstitutionalFree: +1 800 868 0441 Home CareFax: +1 630 307 6195E-mail: [email protected]

STERREICHArjoHuntleigh GmbHDrrstrasse 85

AT-6020 INNSBRUCKTel: +43 (0) 512 204 160 0Fax: +43 (0) 512 204 160 75

47

www.arjohuntleigh.com

ArjoHuntleigh Addresses


48/48

GETINGE GROUPis a leading global provider of products and systems that

contribute to quality enhancement and cost efficiency within healthcare and life

sciences. We operate under the three brands ofArjoHuntleigh, GETINGE and

MAQUET.ArjoHuntleighfocuses on patient mobility and wound management

solutions. GETINGE provides solutions for infection control within healthcare and

contamination prevention within life sciences. MAQUET specializes in solutions,

therapies and products for surgical interventions and intensive care.

www.ArjoHuntleigh.com

ArjoHuntleigh AB

Verkstadsvgen 5

241 38 EslvSWEDEN

Arjo Freedom Bath Manual

Documents

Transcript of Arjo Freedom Bath Manual