ARDUINO BASED TIME AND TEMPERATURE DISPLAY
-
Upload
ajit-kumar-singh -
Category
Engineering
-
view
38 -
download
2
Transcript of ARDUINO BASED TIME AND TEMPERATURE DISPLAY
ARDUINO BASED TIME AND TEMPERATURE DISPLAY
INTRODUCTIONThis project time and temperature display,
displays the time and temperature of surrounding. The LM-35 Analog Temperature Sensor and RTC DS-1307 is interfaced to analog pin of Arduino board, where it has in built ADC which converts these analog reading and displays it on LCD, which indicate time and temperature of surrounding.
COMPONENT REQUIRE Arduino developed board Temperature sensor Time sensor LCD Breadboard Misc(wires,pot etc)
Arduino Board Arduino is a single-board microcontroller. There is a microcontroller unit embedded
on it. The Arduino microcontroller is an easy to
use yet powerful single board computer.
The code is directly loaded from the computer.
Arduino Board The Arduino is open-source, which means
hardware is reasonably priced and development software is free.
It has gained considerable traction in the hobby and professional market.
LM 35 Temperature Sensor LM 35 are used to sense the heat around
it. LM 35 digital sensor has got 3 pin’s i.e.,
VCC, GND and output pin’s when LM 35 is heated the voltage at output pin increases.
It is connected to the analog to digital convertor IC (ADC).
LM 35 Temperature Sensor The LM 35 series are precision integrated-circuit temperature sensor, whose output voltage is linearly proportional to Celsius temperature. The LM 35 does not require any external
calibration or trimming to provide typical accuracies of ±1⁄4˚C at room temperature and ±3⁄4˚C over a full −55 to +150˚C temperature range.
Liquid Crystal Display(LCD) Most common LCDs connected to the
microcontrollers are 16x2 and 20x2 displays.
This means 16 characters per line by 2 lines and 20 characters per line by 2 lines, respectively.
It has a controller chip which receives data from an external source and directly displays it on screen.
Liquid Crystal Display(LCD)If an 8-bit data bus is used the LCD will
require 11 data lines (3 control lines plus the 8 lines for the data bus).
The three control lines are referred to as EN, RS, and RW
EN =Enable (used to tell the LCD that you are sending it data).
RS =Register Select (When RS is low (0), data is
treated as a command).(When RS is High(1), data being sent is text
data ).
Liquid Crystal Display(LCD) R/W = Read/Write (When RW is low (0), the
data written to the LCD).(When RW is low (1), the data reading to the LCD).
Real Time Clock RTC is an 8 pin device using an I2C interface.The DS1307 is a low-power clock/calendar with 56
bytes of battery backup SRAM. The clock/calendar provides seconds, minutes,
hours, day, date, month and year qualified data. The main advantage of RTC is that they have an arrangement of battery backup which keeps it running in case of power
failure
Working Principle The heart of the circuit is an Arduino board
which controls all its functions. An IC LM35 is used as temperature sensor and
RTC ds-1307 is used as a time sensor. The LM-35 analog temperature and RTC 1307
device is interfaced to the analog pin of the Arduino board.
It’s built-in ADC, which converts these analog reading and displays that on the LCD, to indicate temperature and time of the surroundings.
Working Principle Time and temperature can be displayed
in any sequence as desired by doing changes in program uploaded on Arduino.
RTC also help in displaying day of week.
Circuit Inter facing of RTC with
Arduino and LCD
Interfacing of LM 35 with Arduino and LCD
Reference This project is done with the reference of my
ECE teacher Miss Manie Kansal. http://www.alldatasheet.com/ http://www.engineersgarage.com/ https
://m.youtube.com/watch?v=NDwSrgfsiYQ