AAppppLLooaaddeerr UUsseerr GGuuiiddee

CARRIER CORPORATION ©2016 A member of the United Technologies Corporation family · Stock symbol UTX · Catalog No. 11-808-512-01 · 3/18/2016

Verify that you have the most current version of this document from www.hvacpartners.com or your local Carrier office.

Important changes are listed in Document revision history at the end of this document.

CARRIER CORPORATION ©2016. All rights reserved throughout the world. i-Vu is a registered trademark of Carrier Corporation. BACnet is a registered trademark of ASHRAE. All other trademarks are the property of their respective owners.

Contents Installing AppLoader ................................................................................................................................................... 1 Downloading memory ................................................................................................................................................. 2 Changing IP configuration of a router ........................................................................................................................ 3 Document revision history .......................................................................................................................................... 4

AppLoader Carrier Proprietary and Confidential CARRIER CORPORATION ©2016 User Guide All rights reserved 1

AppLoader is a software utility that enables field technicians to restore the original factory settings to a controller.

1 Make sure that the USB Link cable driver is installed.

2 Connect the computer to the controller with the USB Link.

3 Insert the i-Vu® Tech Tools DVD or USB drive into your computer.

4 On your computer, click AppLoader under Other Installs.

NOTE If the screen does not automatically appear after inserting the DVD or USB drive, navigate to I-Vu Tech Tools on your computer and double-click the Apploader folder. Double-click AppLoader_x.x_windows_setup.exe to start the installation.

5 Follow the Setup Wizard and wait for it to finish.

6 In the folders, double-click utilities and open the Clippings folder.

7 Copy the clipping files to a folder on your computer.

NOTE Clipping files contain the controller’s factory image, which may include a driver, control program, graphics, and screen files.

Installing AppLoader

Downloading memory

AppLoader Carrier Proprietary and Confidential CARRIER CORPORATION ©2016 User Guide All rights reserved 2

From your desktop, click Start > All Programs > AppLoader x.x and then click , or browse to your program location.

1 For an Rnet connection, select Options and check Preserve Parameters.

2 Select Connection and check Rnet.

3 Select Access Port and check the COM port for the USB Link.

To find the correct port:

1. From Start or explore, on your computer, right-click Computer and select Manage.

2. Select Device Manager in the tree on the left.

3. Click the arrow next to Ports (COM & LPT1).

4. Your port is listed next to Silicon Labs USB to UART Bridge.

4 In AppLoader, select Baud Rate and check 115200.

5 Select File > Open, browse to the Clipping folder you saved earlier.

6 Select the Clipping file for the controller that you wish to download and then click Open.

7 Click Build. Wait for the message that the build is complete.

8 Click Modstat to verify successful communication. Check your connection if there are problems.

9 If communicating properly, click Download Memory. Wait for the message Download Successful.

NOTE Downloads can take up to 10 minutes, depending on the controller.

Downloading memory

Changing IP configuration of a router

AppLoader Carrier Proprietary and Confidential CARRIER CORPORATION ©2016 User Guide All rights reserved 3

You can change the IP settings of a router in AppLoader, similar to using Hyperterminal. PREREQUISITES

• Use only for the i-Vu® Open Router, i-Vu® Open Link, Carrier® ChillerVu™, or i-Vu® Integrator. You cannot use the i-Vu® CCN Router or i-Vu® Link.

• Make sure DIP switch 1 is in the up position.

NOTE You must cycle power on a router when a DIP switch setting is changed.

1 In AppLoader, select IP Config and verify these settings:

• Connection Type - check Rnet

• Rnet

○ Access Port - select the COM port used for the USB Link. See step 3 in Downloading memory (page 2) if you are unsure which COM port to select.

○ Baud Rate - Select the correct rate, typically 115,200.

1 Click Connect and a dialog shows the Current IP addresses and New address fields that you can change.

2 Enter your IP changes and click Apply.

CAUTION Changing the BACnet Port (BACnet/IP) from the default of 47808 can cause communication problems. If there is a site-specific reason why you must change this default number, contact Carrier Controls Support for assistance.

Changing IP configuration of a router

Document revision history

AppLoader Carrier Proprietary and Confidential CARRIER CORPORATION ©2016 User Guide All rights reserved 4

Important changes to this document are listed below. Minor changes such as typographical or formatting errors are not listed.

Date Topic Change description Code*

3/18/16 Changing IP configuration of a router Carrier® ChillerVu added to list of routers. C-D

* For internal use only

Document revision history

CARRIER CORPORATION ©2016 A member of the United Technologies Corporation family · Stock symbol UTX · Catalog No. 11-808-512-01 · 3/18/2016