Application Note A08-004A Introduction Methods
Transcript of Application Note A08-004A Introduction Methods
[email protected] | www.bibby-scientific.com +44(01785) 810433 1
Application Note A08-004A Discrimination of a single base pair mismatch using
melting analysis
Introduction Melting analysis is frequently used to characterise PCR products post-amplification.
The melting temperature (Tm) of a PCR product is dependent on both the length and
sequence of the DNA and can therefore be used to check for non-specific products of a
reaction or to analyse DNA sequence variations such as insertions, deletions and single
base pair changes. Melting analysis requires the use of an intercalating dye.
Intercalating dyes bind to the minor groove of double-stranded DNA (dsDNA)
producing up to a thousand-fold increase in fluorescence. Third generation fluorescent
dsDNA dyes such as SYTO® 9 and EvaGreen® are able to be used at higher
concentration in the reaction than traditional dyes due to their lower toxicity. This
allows for greater saturation of the dsDNA leading to increased sensitivity, high fidelity
and better resolution in melting curve profiles.
In this application note we demonstrate that using melting analysis, PrimeQ was able to discriminate a single base
pair change (G/A conversion) using various intercalating dyes.
Methods Two artificial 100 base ssDNA templates were synthesized based on the genomic sequence of Enterobacteria
phage lambda (Figure 1). The lambda DNA sequence normally has a G base at position 16404. One of the templates
was synthesized with the G base in this position (“wild type”) and the second with an A in this position (“mutant”).
The primers were designed to amplify a 76 base pair product within the templates, encompassing the base change.
Selecting a short product ensures that the mismatch will have greatest effect on the overall Tm of the product.
Figure 1: Sequences of the lambda DNA templates and primers. The 100 base artificial templates were based on the sequence of bases 16361
to 16460 inclusive (accession number J02459.1). The “wild type” template had a G base at position 16404 and the “mutant” an A base.
Primers were designed using NCBI Primer-BLAST and are shown in blue and green.
Four different reagent kits were used for amplification and detection of the products (Table 1).
Kit name Supplier Part code
JumpStart™ Taq ReadyMix™ Sigma S4438
AccuMelt™ HRM SuperMix Quanta
Biosciences™
95103-250
Fast EvaGreen® qPCR Master Mix Biotium 31003
QuantiFast® PCR Kit Qiagen 204052
Table 1: Details of the reagent kits used. All kits were supplied as complete 2X master mixes.
Approximately 5 x 105 copies of either template were used per reaction. Six replicates of either template were run
for each kit plus two no template controls (NTC). The final primer concentration was 0.2µM and ROX™ passive
[email protected] |www.bibby-scientific.com +44(01785) 810433 2
A08-004A: Discrimination of a single base pair mismatch
reference dye (PRD) was added to each mix to a final concentration of 40nM except QuantiFast® (which already
contained a PRD). White, low profile 96-well plates were used (Brand; part code 781365) and heat sealed with
optically clear heat sealing film (Clear Seal Diamond, Thermo Scientific; part code AB-0812). The reactions were
amplified for 35 cycles (initial denaturation, 95°C, 2 min; 35 cycles of 95°C, 5s; 60°C, 20s; reading with filter sets
FC02 and FC04). At the end of the amplification stage, a ramp stage was performed (72°C to 91°C in 0.2°C steps,
hold time 10 seconds per step, reading with filter set FC02).
Results Single base changes in DNA, sometimes known as SNPs (single nucleotide polymorphisms) are classified into 4
groups as summarised in Table 2.
SNP class Base change Typical Tm curve shift Frequency in the human
genome
1 C/T and G/A Large (>0.5°C) 64%
2 C/A and G/T Large (>0.5°C) 20%
3 C/G Small (0.2-0.5°C) 9%
4 A/T Small (<0.2°) 7%
Table 2: SNP classes and occurrence in the human genome (1).
G to A base changes are designated as class 1 SNPs and are one of the easiest types to detect due to the relatively
large shift in Tm; they are also one of the most frequently found class of SNPs in the human genome. Figure 2 shows
the amplification curves of the products obtained from all the kits on the same scale with no PRD correction. It is
quite clear that kits containing third generation dsDNA dyes (AccuMelt™ and Fast EvaGreen®) show a much greater
final fluorescence than those containing traditional intercalating dyes. The latter kits reached a plateau at a much
earlier cycle number whereas the SYTO® 9 and EvaGreen® kits continued to amplify in an extended linear phase
before reaching a final plateau.
The ramp stage was analysed using the dissociation curve analysis in Quansoft and Figure 3 shows the melting
curves and melting peaks for both the “wild type” and “mutant” templates using each of the kits. In each case, the
six replicates for each template type were clearly distinct. For further analysis, the raw fluorescence data for the
samples amplified using the QuantiFast® kit were exported to Excel. The melting curves were normalised between
78°C and 91°C such that the fluorescent signal at 78°C was set to 100% and the signal at 91°C, 0%. This helps to
“tidy” the data and aids in interpretation. To further enhance the differences between curves, they can be plotted
Amplification
Cycle Number34323028262422201816
Relative Fluorescence
700,000
650,000
600,000
550,000
500,000
450,000
400,000
350,000
300,000
250,000
200,000
150,000
100,000
50,000
0
Figure 2: Amplification curves for the two templates with each of the
kits. Red = AccuMelt™, purple = EvaGreen®, green = JumpStart™, yellow
= QuantiFast®, blue = NTCs. The NTCs showed a small increase in
amplification towards the end of the run due to non-specific
amplification.
[email protected] |www.bibby-scientific.com +44(01785) 810433 3
A08-004A: Discrimination of a single base pair mismatch
on a difference graph. A curve is selected as a reference and the difference in fluorescence between the samples
and reference is plotted. These two graphs are shown in Figure 4.
Figure 3: Dissociation curves and melting peaks for each of the templates obtained with the reagents used. In each case the “wild type”, (G
template) is shown in green and the “mutant”, (A template) in red. As expected, the “mutant” template has a lower Tm.
Figure 4: Normalised melting curve data and difference curves for “wild type” and “mutant” samples amplified using the QuantiFast® kit. The
reference used for the difference plots was one of the “wild type” melting curves. These two plots clearly demonstrate the difference in Tm
between the two sets of samples.
The Tm of a product is strongly influenced by the reaction mixes, which may vary in unspecified additives and
differences in salt concentrations and this is apparent from the data presented in Figure 5 and Table 3, where the
Tm for the “wild type” sample was found to vary between 81.61°C and 83.76°C. The shift in Tm (ΔTm) also varied
quite significantly depending on which kit was used. Of the reagents tested, those containing traditional
intercalating dyes (QuantiFast® and JumpStart™) showed the greatest shift in Tm between the “wild type” and
“mutant” PCR products in this particular assay.
JumpStart™ AccuMelt™ Fast EvaGreen® QuantiFast®
G A G A G A G A
Average Tm
+/-SD (°C)
83.20 +/-
0.019
82.43 +/-
0.050
83.76 +/-
0.094
83.21 +/-
0.040
81.61 +/-
0.031
80.87 +/-
0.082
82.90 +/-
0.021
82.03 +/-
0.061
ΔTm (°C) 0.77 0.55 0.74 0.87
Table 3: Data from Figure 5 showing the Tm shift observed with each of the kits for the single base mismatch.
[email protected] |www.bibby-scientific.com +44(01785) 810433 4
A08-004A: Discrimination of a single base pair mismatch
Conclusions Melting analysis in qPCR has traditionally been used to identify non-specific products or contamination following
amplification. A melting curve is generated by slowly denaturing the DNA in the presence of a dsDNA binding dye.
Small variations in sequence result in differences in Tm, which is defined as the point at which 50% of the DNA is
double stranded and 50% is single stranded. High Resolution Melting (HRM) is an emerging technique which uses
these small changes in Tm together with the shape of the melting curves to characterize genetic variations. Using
this technique, fluorescence data is collected at very small temperature increments in order to obtain the highest
resolution melting curves. Special software is also required in order to analyse fully the subtle differences in curve
shape or Tm differences of products. This, combined with reagents and dyes designed specifically for HRM, results
in a powerful technique for high throughput screening for genetic variation.
In this application note we designed a class 1 SNP variation and demonstrated that PrimeQ is able to distinguish a
single base pair mismatch (G/A) using the standard melting curve analysis software available in Quansoft based on
a change in Tm of the product. This analysis can be further enhanced by exporting the raw data to Microsoft® Excel
in order to generate normalised and difference curves. In addition, the products were easily distinguishable using
all of the intercalating dyes tested. Class 1 and 2 SNPs are the easiest to detect due to the relatively large Tm shift;
we have not tested class 3 or 4 SNPs as these are relatively rare and the typical ΔTm (~0.2°C) might prove difficult to
interpret due to being right at the edge of the capability of the thermal block of PrimeQ.
References (1) J. Craig Venter et al. The Sequence of the Human Genome Science 291, 1304 (2001);
DOI:10.1126/science.1058040
Trademarks
EvaGreen® is a registered trademark of Biotium, Inc.
ROX™ is a trademark of Applera Corporation.
QuantiFast® is a registered trademark of Qiagen Group
AccuMelt™ is a trademark of Quanta BioSciences, Inc.
SYTO® is a registered trademark of Life Technologies Corporation (Molecular Probes Labelling and Detection Technologies).
JumpStart™ is a trademark of Sigma-Aldrich Co. LLC
80.00
80.50
81.00
81.50
82.00
82.50
83.00
83.50
84.00
84.50
G A G A G A G A
JumpStart™ AccuMelt™ EvaGreen® QuantiFast®
Tm
(°C
)
Figure 5: Tm values for the PCR products determined in each of
the reaction mixes.