Application Kit Manual TC3X7 V2 - Mouser...User Manual 2-1 V2.0 Application Kit TC3X7 V2.0 2018-06...

User Manual Please read the Important Notice and Warnings at the end of this document V2.0www.infineon.com Application Kit TC3X7 V2.0 2018-06

Application Kit TC3X7

Application Kit Manual TC3X7Hardware: Appl ication Kit TC3X7 V2.0

About this document

Scope and purpose

The User Manual provide information about using, configuration and connecting the Application Kit withInfineon AURIX™ TC3X7 device.This Application Kit Hardware Manual familiarizes you with the TriCore Evaluation Board and guides you throughthe initial configuration of the Application Kit.

Intended audience

Design, verfication, test and software engineers will use this document to get an understanding of thefunctionality and connections of the Application Kit.

User Manual TOC-2 V2.0 Application Kit TC3X7 V2.0 2018-06

Application Kit Manual TC3X7Hardware: Application Kit TC3X7 V2.0

Table of Contents

About this document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Preface-1

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TOC-2

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12.1 Summary of Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12.2 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22.3 Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

3 Application Kit Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13.1 Available Boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13.2 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13.2.1 Power via supply connector (X101) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13.2.2 Power via Micro USB (BU301) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23.2.3 Multi Voltage Safety Micro Processor Supply TLF35584QV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23.3 Real Time Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23.4 XGA Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-33.4.1 Write a display register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-33.4.2 Read a display register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-33.4.3 Touch controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-43.5 Micro SD card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-43.6 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-43.7 Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-43.8 USB Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-43.8.1 Serial Connection to PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-53.8.2 miniWiggler JDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-53.9 Beeper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-53.10 MultiCAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-53.11 LIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-53.12 Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-53.13 Core current measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-63.14 Other peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-63.15 Toggle LED’s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-63.16 Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-63.17 Debug System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-63.17.1 OCDS1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-63.17.2 DAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

4 Application Kit Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14.1 Default Pad State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14.2 Bootmode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

5 Signal (on board used) Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15.1 Power Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15.2 Reset Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15.3 Config Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15.4 Clock Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-25.5 Debug Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-25.6 Peripheral Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2

Table of Contents

User Manual TOC-3 V2.0 Application Kit TC3X7 V2.0 2018-06


Table of Contents

6 Connector Pin Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-16.1 I/O connectors TC387 and TC397 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-16.2 Power connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-16.3 USB connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-26.4 CAN connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-26.5 LIN connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-26.6 Ethernet connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-36.7 OCDS1 connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-36.8 DAP connector pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3

7 Schematic and Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-17.1 Known problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-17.2 Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-17.3 Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-67.4 Layout with Dimensioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8

User Manual 1-1 V2.0 Application Kit TC3X7 V2.0 2018-06


Introduction

1 IntroductionWe congratulate you on your purchase of the TriCore Evaluation Board. This kit is a versatile tool, providing quickaccess to the capabilities of TriCore's powerful architecture.Applications can be developed easily. The Evaluation Board is equipped with a variety of memories andperipherals for connection to the environment. There is also an interface for the On Chip Debugging Features(OCDS1 and DAP). The Evaluation Board allows easily the development of TriCore applications with the corresponding tools.Subsequently, the applications can be downloaded and can be tested with the powerful debugger software.This Application Kit Hardware Manual familiarizes you with the TriCore Evaluation Board and guides you throughthe initial configuration of the Application Kit. For detailed technical information about the TC3X7 (e.g. TC397) please refer to the User Manual of the useddevice.



Features

2 Features

2.1 Summary of Features– Infineon’s TC3X7 (TC397, TC387) AURIX™ 2G Controller in LFBGA-292 Package– LCD XGA Display 320x240– SD card slot (mini SD)– High Speed CAN Transceiver (CAN FD capable)– USB to UART bridge– Ethernet Gigabit PHY– LIN Transceiver– Crystal 20MHz (default) or External Clock– USB miniWiggler JDS for easy debugging– 4 Low Power Status LEDs– RTC with alarm– Acoustic beeper– 100mm x 100mm

ConnectorsThe Application Kit TC3X7 offers a wide variety of connectors:

– Standard power connector– Micro USB connector for ASC Interface (ASC0) and miniWiggler– RJ45 connector for Ethernet (if Gigabit Ethernet supported by assembled CPU)– 16-pin header for JTAG interface (OCDS)– 10-pin header for DAP– 10pin (2x5) Header for LIN Transceiver (LIN)– 10pin (2x5) Header for CAN High Speed Transceiver (CAN0)– two 40-pin connectors with I/O signals– mini SD card slot

Components– Infineon’s Multi Voltage Safety Micro Processor Supply TLF35584QV– LED to validate power supply (5V or 3,3Volt)– LED indicating RESET (ESR0) active state– LED indicating activ miniWiggler JDS– LED switched via DAS software– Infineon’s High Speed CAN Transceiver TLE 9251V (CAN FD capable)– Infineon’s LIN-Transceiver TLE 7259-3GE– QSPI Real-Time Clock/Calendar with SRAM and unique MAC Id MCP79511 (if CPU not support I2C)– I2C Real-Time Clock/Calendar with SRAM and unique MAC Id MCP79411 (if CPU support I2C)– USB to UART bridge FT2232HL (FTDI)– Integrated 10/100/1000M Ethernet Precision Transceiver RTL8211FI-CG (Realtek)– Touch screen controller ADS7843– 4 general purpose LEDs– Reset switch– Wake switch– Xilinx CPLD XC9572XL



Features

2.2 Block Diagram

Figure 2-1 Application Kit TC3X7 Block Schematic

MicroUSB miniWiggler

OCDS1

USB

XTAL

CAN Transceiver

P20.8 or P10.3

P20.7 or P10.2

TC3X7(TC397, TC387)TriCoreCPU

PLLCAN0

P14.0

P14.1

4 LED’s (P13.0 up to

P13.3)

Multi Voltage Safety Micro Processor Supply

TLF35584QV5V or 3,3V version

RGMII (P11, P12) PHYTwisted Pair

RJ45

LIN LIN

Transceiver

P10.5

P10.6

Mic

ro

SD

Car

d

QSPI0 (P20) Serial to Parallel

converter

XGA Display320x240

with touch

QSPI1 (P10) or SDMMC

Acoustic Beeper

P33.

0

RTCI2C (P15) or QSPI4 (P22)

P33.7

WAKEUPWAKE

QSPI2 (P15)

QSP

I2



Features

2.3 Placement

Figure 2-2 Application Kit TC3X7 V2.0 Top Placement

U101

Y201

U203

JP201

R166C105

C120

L103

Q104

C11

6

C121

U10

5

R130

BT101

U104

U201

X203

C20

9

D301

BU301

D302 U301

Y30

1

U206

X201

X301

U202

C107

C11

4

L101

L102

LS10

1U102

X101

X102

X103X2

05

Y101

Y102

X202

X302

U103

X204



Features

Figure 2-3 Application Kit TC3X7 V2.0 Bottom Placement

LCD201

D103

D102

U205

U305

U303

U302

CB221

D101

D105

D106

D107

D108

D109

D110

S101

S102

D104



Application Kit Information

3 Application Kit Information

3.1 Available BoardsThe following boards are available:

– Application Kit TC397 V2.0 with VEXT=5V– Application Kit TC397 V2.0 with VEXT=3,3V– Application Kit TC387 V2.0 with VEXT=5V– Application Kit TC387 V2.0 with VEXT=3,3V

If the TLF35584 is stamped with VS1 then the board has VEXT=5V.If the TLF35584 is stamped with VS2 then the board has VEXT=3,3V.The used VEXT voltage can also be detected by the supply measurement of the AURIX™ device itself and osmeasureable on pin 2 of X102 and X103.

Note: Only on Application Kit TC397 V2.0 with VEXT=3,3V is the SD card connected to the TC397 via SDMMC module and P10.2/3 is used for CAN. All other boards are using QSPI for SD card access and P20.7/8 for CAN.

3.2 Power SupplyAll needed voltages are generated via Infineon’s Multi Voltage Safety Micro Processor Supply TLF35584QV and viathe microcontroller itself (+1,25V).The supply device is available as two different devices:TLF35584QVVS1 -> +5V standby voltage, +5V TriCore supply (V_UC)TLF35584QVVS2 -> +3,3V standby voltage, +3,3V TriCore supply (V_UC)Dependent of the assembled device the board works with 5V or 3,3V IO.The TLF35584QV provide the following voltages:+3,3V or +5V for standby (connected to VEVRSB)+3,3V or +5V for TriCore (connected to VEXT)+5V communcation supply (used by CAN transceiver and acoustic beeper)+5V voltage reference (connected to VDDM and VAREFx)+3,3V via LDO directly from pre regulator (connected to VDDP3 and VFLEX and used by Ethernet PHY, display andSD card)Applying a stable supply voltage causes the power on reset after a short period. The LED (V_UC) indicate thestatus of the cpu voltage.A manual power on reset is executed by pressing the reset button.The Board has to be connected to a +3,5V to +40V DC power supply.The board can be powered directly by USB or by the power connector. In case that the voltage on the powerconnector is higher than the 5V from the USB then the board is powered by power connector.

3.2.1 Power via supply connector (X101)The Board has to be connected to a +5,5V to +40V DC power supply. A supply with 6V and 800mA is sufficient. The pinout for the supply connector is shown in Figure 6-2. There can beused any standard power pack with a connector where the positive line is surrounded by the ground line.




3.2.2 Power via Micro USB (BU301)The Board can also be powered by the Micro USB connector. The power consumption of the board is higher than500mA. Use an USB port which can deliver 900mA (USB 3.0). Most USB hubs are not able to drive more than100mA and can’t be used. Also it is possible to power the board with a cellular battery charger which has 5V output and use Micro USB forconnecting.The pinout for the USB connector is shown in Figure 6-3.

3.2.3 Multi Voltage Safety Micro Processor Supply TLF35584QVThe board has assembled the Safety Micro Processor Supply with the following Features:

– High efficient multi voltage power supply chip– Serial step up and step down pre regulator for wide input voltage range from 3.0 to 40 V with full

performance and low over all power loss– Low drop post regulator 5.0V/200mA for communication supply (named LDO_Com)– Low drop post regulator 3.3 V/600 mA (VS2) or 5.0V/600mA (VS1) for μC supply (named LDO_μC)– Provides enable, sync out signal and voltage monitoring (inside device to be added to reset function) for an

optional external post regulator for core supply (not used)– Voltage reference 5.0 V +/- 1% for ADC supply, 150 mA current capability (named Volt_Ref)– Two trackers for sensor supply following voltage reference 150 mA current capability each (named Tracker

1 and Tracker 2, not used)– Standby regulator 3.3 V/10 mA (VS2) or 5.0 V/10 mA (VS1) (named LDO_Stby)– Independent voltage monitoring block with reset function– Configurable functional and window watchdog– 16-bit SPI– Safe state control with two safe state signals with programmable delay– Input voltage monitoring (over voltage switch off)– Green Product (RoHS compliant)– ISO26262 compliant– AEC Qualified

The TLF35584 is connected to the CPU via QSPI2 and use QSPI2_SLSO1 (P14.2) as chip select. Via this spiconnection the power supply will be configured (Watchdog, device states and soon).For more information see the data sheet of TLF35584.

Note: The switch to FAILSAFE state is switched off by HW (R127 assembled). If you will use/evaluate all safety features of the TLF35584 make sure that R127 is not assembled and remove R127 if assembled. Make sure that you have a proper initialization of TLF35584 in your software and debugger in this case. If needed you can assemble JP201 (2 pin header). Then you can switch easily with a jumper.

3.3 Real Time ClockThe board is equipped with a RTC MCP79511 (if I2C is not supported by CPU) or MCP79411 (if I2C is supported byCPU) from Microchip. The device is powered from the standby voltage of the TLF35584 and is also powered whenthe TLF35584 is switched to standby mode. For backup when the TLF35584 is not powered then there is a smallbattery to hold the value inside the RTC. The MCP79511 is connected to the microcontroller via QSPI4, theMCP79411 is connected to the microcontroller via I2C on P15.4/P15.5. The RTC can trigger an SCU_REQ4 (P33.7)interrupt (activ low) with the alarms. Also an alarm from the RTC will wake-up (switch on) the board if the boardis powered and the supply is switched off.




The MCP79511/MCP79411 contains also an unique ID in the format EUI-48. This id can be used as mac id forethernet if the assembled CPU support ethernet.For more information about the RTC please see the datasheet of MCP79511/MCP79411.

3.4 XGA DisplayThe board has an XGA Display with a resolution of 320x240. The display has an ILI9341 display controller. Pleasesee the datasheet of the display controller for the register of the controller. The display is connected to the themicrocontroller via an SPI to Parallel converter (U201).The SPI to Parallel converter is based on a statemachine. This state machine is clocked with the clock of SPI, hereSCLK0 (P20.13). Each rising edge of P20.13 will change the state of statemachine. When SLSO08 (P20.6) is not lowthen the state machine will go always in the idle state with a valid clock edge.The backgound light is switched on via port 15 pin 0. An high level on this port pin enable the backgound light.

3.4.1 Write a display registerA single write to any register can be done by a 32 bit transfer of SPI. Make sure that the SLSO08 is low during this32 bit. Bit 31 must be transfered first.Bit 31 must be 0, this will be indicate a write access.Bit 30 must be 0, this will be indicate a single access.Bit 29...Bit 22 is the 8 bit register number which will be writtenBit 21...Bit 6 is the 16bit value which will be writtenBit 5...Bit 0 are dummy bits which are used to execute the write.To speedup the writing (e.g. write to ram of display controller) it is possible to make a endless transfer. This isdone by this:first 10 bit transferBit 9 must be 0, this will be indicate a write access.Bit 8 must be 1, this will be indicate an endless transfer.Bit 7...Bit 0 is the 8 bit register number which will be writtenNow you need to transfer only 16bit values for the registers. With the first 16 bit value there is no action on thedisplay. With the second value transfer is a write to the register started. This means after the last value you mustmake a dummy transfer to write the last value. The endless mode can only be leave by a rising edge of SCLK0 with SLSO08 set to high. This can be done by adummy transfer to any other chip select or by a transfer from the touch controller.

3.4.2 Read a display registerA single read from any register can be done by a 32 bit transfer of SPI. Make sure that the SLSO08 is low during thecomplete transfer.first transfer has 16 bit:Bit 15 must be 1, this will be indicate a read access.Bit 14 must be 0, this will be indicate a single access.Bit 13...Bit 7 is the 8 bit register number which will be readBit 5...Bit 0 are dummy bits to setup the register number.second transfer must have 26 bits:Bit 25...Bit 16 are dummy bits which are needed to readout the register value




Bit 15...Bit 0 are dummy bits to transfer the readed value.To speedup the reading (e.g. reading from ram of display controller) it is possible to make a endless transfer. Thisis done by this:first 16 bit transfer:first transfer has 16 bit:Bit 15 must be 1, this will be indicate a read access.Bit 14 must be 1, this will be indicate an endless access.Bit 13...Bit 7 is the 8 bit register number which will be readBit 5...Bit 0 are dummy bits to setup the register number.second 10 bit transfer:Bit 9...Bit 0 are dummy bits which are needed to readout the register valueNow you need to transfer only 16bit values for the registers. With the each 16 bit transfer you get a value. With thelast transfer you have dummy read which you don’t get the result. The endless mode can only be leave by a rising edge of SCLK0 with SLSO08 set to high. This can be done by adummy transfer to any other chip select or by a transfer from the touch controller.

3.4.3 Touch controllerThe touch of display is connected to an Touch controller ADS7843. This controller is connected via the QSPI0 andSLSO9 (P20.3) to the microcontroller. For more information about the delivered values from the touch controllerplease see the datasheet of ADS7348.

3.5 Micro SD cardThe board has a slot to use the board with an micro SD card. If the board is assembled with TC397 and aTLF35584QVVS2 (3,3V version) then the SDMMC module is connected directly to the SD card. In this case R251 upto R256 are assembled instead of R261 up to R268.In all other cases the card can be used in SPI mode only. In this case the SD card is connected to QSPI1 with chipselect 9 (P10.5) of QSPI1.Please see additional literature how to use a SD card in SPI mode.

3.6 LEDsThere are 8 LEDs on board:

– D107 up to D110 (blue) -> toogle LEDs connected to P13.0 ... P13.3– D106 ESR0 (red) -> RESET LED indicate the reset state of the board– D105 V_UC (green) -> V_UC power supply indication– D104 SS2 (green) -> safe state signal 2 of TLF35584– D302 ACT (green) -> on board miniWiggler JDS is ACTIV– D301 RUN (blue) -> Debug RUN mode (switched by DAS Server)

3.7 ClockOn the board is a fixed crystal with 20MHz assembled. You can change this by replacing Y101 (soldered).

3.8 USB ConnectorThe USB connector is used for connection to a PC. Via the USB it is possible to power the board, using the ASCLIN0as serial connection via USB and Debugging via DAS. For the pinout of USB socket see Figure 6-3.




NOTE: Before connecting the board to the PC, make sure that the actual DAS software is installed on the PC. Foractual DAS software please contact your local FAE.The software can also be found on:

DAS website3.8.1 Serial Connection to PCAfter the first connection of USB to a PC the needed driver will be installed automatically. During this there willbe created a new COM port on PC. This COM port can be used to communicate with the board via ASCLIN0 of thedevice. Per default the ASCLIN0 is used on P14.0 and P14.1 (e.g. Generic Bootstrap Loader) .

3.8.2 miniWiggler JDSThe miniWiggler JDS is a low cost debug tool which allows you access to the JTAG of the device. Make sure thatyou have the latest DAS release. Debugging is possible via the DAS Server ‘UDAS‘. Please contact your prefereddebug vendor for support of DAS.If you have connected the board to the PC and there runs the DAS server, then a working connection is visible viathe green ACTIV LED.The status RUN LED is switched on/off through the DAS Server, depending on the used debugger (client).IMPORTANT: Make sure that there is no or a tristated connection on X301 (OCDS1) and X302 (DAP) if the ACTIV LEDis on.

3.9 BeeperThe board has an electro-acoustic transducer which can be used for an acoustic output. The transducer isconnected to pin P33.0 and needs a 2048Hz frequency.

3.10 MultiCANOn the board is one CAN transceiver (CAN FD capable) connected to the CAN module 0 node 0 (P20.7 and P20.8)on TC3X7. Optional the CAN transceiver can be connected to CAN module 0 node 2 (P10.2 and P10.3). To do thisremove resistor R269, R270 and assemble R257, R258 with 0R Resistor. For location of this resistors please see theTop Layer assembling Figure 7-5.

Note: If the board is assembled with TC397 and TLF35584QVVS2 (3,3V version) then the SDMMC module is connected directly to the SD card. In this case P20.7 and P20.8 are used by the SDMMC and the transceiver is connected to P10.2 and P10.3.

The transceiver is connected to an IDC10 plug. For the pinout of IDC10 plug see Figure 6-4. You can use a IDCfemale connector with crimpconnector, flat cable and SUB-D 9 plug with crimpconnector to have a 1:1 adapterto SUB-D 9.

3.11 LINOn the board is one LIN transceiver connected to the ASCLIN2 (P10.5 and P10.6) on TC3X7. The transceiver areconnected to one IDC10 plug. For the pinout of IDC10 plug see Figure 6-5. You can use a IDC female connector withcrimpconnector, flat cable and SUB-D 9 plug with crimpconnector to have a 1:1 adapter to SUB-D 9.

3.12 EthernetThe Application Kit provide a RJ45 connector (X204) for twisted pair ethernet connections.The board use aRealtek Integrated 10/100/1000M Ethernet Precision Transceiver RTL8211FI-CG as physical interface device. For

http://www.infineon.com/das




more information about the ethernet modul see TC3X7 User’s Manual, about the PHY see the RTL8211Fdatasheet. For the pinout of RJ45 see Figure 6-6.For the connection between TriCore and PHY is used the RGMII.

3.13 Core current measurementIt is possible to measure the core (+1,25V) current with two ADC pins of the CPU. This can be done by synchronousmeasurement of AN36 and AN44. The pins are connected togheter by an 50mOhm resistor. The current can becalculated by the following formula:Icore = (VAN44 - VAN36) / 0,05. To get an valid result the measurement must be done synchronous.

3.14 Other peripheralsFor all other peripherals there are no special plugs on the board. Many of the peripheral signals are available onthe two standard connectors X102 and X103, see “Connector Pin Assignment” on Page 6-1.

3.15 Toggle LED’sThe status LED’s are low active and can be controlled by Software.Port 13 pin 0 up to pin 3 are connected to single LED’s (D107... D110) and powered by the normal microcontrollervoltage.

3.16 ButtonsOn the board are two buttons.The reset button (S101) will apply a warm power on reset to the device.The WAKE button (S102) will be used to enable/wakeup the TLF35584.

3.17 Debug System

3.17.1 OCDS1The OCDS1 signals are connected to the IDC16 plug (X401). They work with the port supply of Microcontroller (+5Vdefault or +3,3V). For pinout of the connector see Figure 6-7. You can connect any debugger to this connector. The signals /BRKIN and /BRKOUT are not connected.If you connect a debug hardware make sure that the miniWiggler JDS (see “miniWiggler JDS” on Page 3-5) is notactiv (ACTIV LED is off) and on the DAP connector (X302) is no hardware connected or the hardware is tristated. If the ACTIV LED is on, then stop the active DAS Server ’UDAS’ and/or remove the USB connection to the PC.

3.17.2 DAPThe board comes with a DAP connector (X302). For pinout of this connector see Figure 6-8. You can connect a DAPhardware here. If you use this connector make sure that the miniWiggler JDS is not activ (ACTIV LED is off) and aconnected OCDS1 hardware is disconnected or tristated.



Application Kit Configuration

4 Application Kit ConfigurationThe Application Kit has a fixed configuration which can be sligthly changed. For locating components seeFigure 7-5 and Figure 7-6.

4.1 Default Pad StateThe default pad state is that the internal pull-up devices on the I/O pins are enabled. This can be changed byassembling resistor R143 with 2K2 (drive P14.4 / HWCFG6 low). If the resistor R143 is assembled then all I/O pinsare in tristate. Additonal you must make sure that R134 is also assembled with 10K that the EVRC is enabledproperly in this case.

4.2 BootmodeThe bootmode is fixed set to Start-up mode is selected by Boot Mode Index. This can be changed to boot frompins and Internal Start from Flash by removing resistor R133 (drive P14.3 / HWCFG3 high) and assembling resistorR142 with 2K2 (drive P14.3 / HWCFG3 low). If the I/O pins are set to tristate per default (R143 assembled) then youmust assemble also resistor R134 and resistor R272 with 10K to set the HWCFG pins to proper values.



Signal (on board used) Description

5 Signal (on board used) DescriptionFor more information about the signals please see the user manual/datasheet for TC3X7 and/or the schematicsof the board.All not mentioned signals are not used on the board and can be used outside if they are connected to the IOConnectors see Figure 6-1. Optional marked signals are used only if they are connected (default is that they arenot used on the board).

5.1 Power Signals

5.2 Reset Signals

5.3 Config Signals

Table 5-1 Power Signals

Short name Description

VCC_IN Supply Input (3,5V...40V)

VIN Input Voltage of Power Supply Device

GND Ground

V_PREPEG Pre Regulator Voltage (~5,8V)

+3V3 Supply Voltage (3,3V)

+5V Supply Voltage (5V)

V_UC Microcontroller Supply Voltage (5V or 3,3V depends on assembled TLF35584)

VREF_5V Reference Supply Voltage (5V)

QST Standby Supply Voltage (5V or 3,3V depends on assembled TLF35584)

VDD Core Supply Voltage (1,25V)

VDDM ADC Analog Part Supply Voltage (5V or 3,3V selectable via 1R resistors)

VAREF1 ADC Reference Voltage 1 (5V or 3,3V selectable via 4R7 resistors)

VAREF2 ADC Reference Voltage 2 (5V or 3,3V selectable via 4R7 resistors)

VDD_USB Supply Voltage from USB (5V)

VDD_FT Supply Voltage FT2232HL device (3,3V)

Table 5-2 Reset Signals


/PORST Power On Reset

/ESR0 External Service Request 0 (Hardware Reset)

/ESR1 External Service Request 1 (Non Maskable Interrupt)

Table 5-3 Config Signals


P14.5 HWCFG1 (EVR33OFF)

P14.2 HWCFG2 (EVRCON)

P14.4 HWCFG6 (Pins in tristate / Pins with pull-up)




5.4 Clock Signals

5.5 Debug Signals

5.6 Peripheral Signals

P14.3 HWCFG3 (Boot from pins / Boot from Flash BMI)

P10.5 HWCFG4 (Boot from internal flash)

P10.6 HWCFG5 (Boot from internal flash )

Table 5-4 Clock Signals


XTAL1 Crystal Oscillator Input

XTAL2 Crystal Oscillator Output

Table 5-5 Debug Signals


/TRST Test Reset

DAP0 Device Access Port Line 0 / Test Data Clock (TCK)

DAP1 Device Access Port Line 1 / Test Data Select (TMS)

P21.6 Test Data Input (TDI)

P21.7 DAP2 / TDO from debug connectors

Table 5-6 Peripheral Signals


P14.1 ASCLIN0 Receive Input A

P14.0 ASCLIN0 Transmit Output

P10.6 ASCLIN2 Receive Input D

P10.5 ASCLIN2 Transmit Output

P15.4 I2C0 Serial Clock

P15.5 I2C0 Serial Data Input C und Output

P33.7 RTC Alarm Interrupt Input

P20.7 CAN00 Receive Input B

P20.8 CAN00 Transmit Output

P10.2 CAN02 Receive Input E (optional)

P10.3 CAN02 Transmit Output (optional)

P11.0 Ethernet TXD3 Output



Table 5-3 Config Signals (continued)






P11.4 Ethernet TXCLK Output

P11.5 Ethernet GREFCLK Input

P11.6 Ethernet TCTL Output

P11.7 Ethernet RXD3 Input A




P11.11 Ethernet RCTL Input A

P11.12 Ethernet RXCLK Input A

P12.0 Ethernet Management Data Clock Output (MDC)

P12.1 Ethernet Management Data Input/Output (MDIO)

P10.8 Ethernet MD Interrupt Input

P02.1 Ethernet MD Interrupt Input (optional)

P14.2 QSPI2 Slave Select Output 1 for /SCS of TLF35584

P15.3 QSPI2 Master Clock Output for SCL of TLF35584

P15.6 QSPI2 Master Transmit Output for SDI of TLF35584

P15.7 QSPI2 Master Receive Input B for SDO from TLF35584

P14.3 Output for Watchdog Input of TLF35584

P33.8 SMU_FSP0 Output for Error Signal Input of TLF35584

P33.9 Input for Safe State Signal 1 from TLF35584

P20.6 QSPI0 Slave Select Output 8 for /CS of Display

P20.3 QSPI0 Slave Select Output 9 for /CS of Touch

P20.13 QSPI0 Master Clock Output for SCLK of Display and Touch

P20.14 QSPI0 Master Transmit Output for SDI of Display and Touch

P20.12 QSPI0 Master Receive Input A for SDO from Display and Touch

P20.9 Interrupt Input from Touch /PENIRQ

P15.0 PWM or static Output for Display Backlights

P10.5 QSPI1 Slave Select Output 9 for /CS of SD card

P10.2 QSPI1 Master Clock Output for SCLK of SD card

P10.3 QSPI1 Master Transmit Output for SDI of SD card

P10.1 QSPI1 Master Receive Input A for SDO from SD card

P10.7 Interrupt Input from Card Detect Signal

P02.0 Interrupt Input from Card Detect Signal (optional)

P13[0...3] On board LED’s

P33.0 PWM Signal for Acoustic beeper

P23.1 QSPI4 Slave Select Output 6 for CS of MPC79511 (optional)

P22.3 QSPI4 Master Clock Output for SCK of MPC79511 (optional)

Table 5-6 Peripheral Signals (continued)





P22.0 QSPI4 Master Transmit Output for SI of MPC79511 (optional)

P22.1 QSPI4 Master Receive Input B for SO from MPC79511 (optional)

P15.1 SDMMC0 Clock Output for SD card (optional)

P15.3 SDMMC0 Command Output for SD card (optional)

P20.7 SDMMC0 Data 0 Input/Output for SD card (optional)




Table 5-6 Peripheral Signals (continued)




Connector Pin Assignment

6 Connector Pin AssignmentThe Application Kit will be shipped with two 40 pin male (plug) connectors on top layer with a standard grid of2,54mm.

6.1 I/O connectors TC387 and TC397

Figure 6-1 IO connectors for TC387 and TC397 - Pinout

Note: VCC_IN is connected to X102 and X103 with a 0R resistor which is not assembled by default to avoid shortcut to VEXT in case of measurement on the connector. If VCC_IN needed on X102 and X103 then assemble R113 with a resistor 0R size 0805. Pin 1 of X102 and X103 are always connected together.

6.2 Power connector pinout

Figure 6-2 Power connector pinout (Roka 520 2550)

(VCC_IN) 1 2 V_UC P14.5 40 39 P14.4GND 3 4 GND P33.10 38 37 P33.9P21.2 5 6 P21.3 P15.7 36 35 P15.6P14.8 7 8 P14.7 P15.5 34 33 P15.4P14.6 9 10 P20.0 P15.8 32 31 P15.2P21.4 11 12 P21.5 P22.3 30 29 P22.2P02.0 13 14 P02.1 P22.1 28 27 P22.0P02.2 15 16 P02.3 P33.11 26 25 P23.4P02.4 17 18 P02.5 P23.3 24 23 P23.2P02.6 19 20 P02.7 P23.1 22 21 P23.0P02.8 21 22 P00.0 P33.6 20 19 P33.8P00.1 23 24 P00.2 P33.12 18 17 P33.1P00.3 25 26 P00.4 P33.2 16 15 P33.3P00.5 27 28 P00.6 P33.4 14 13 P33.5P00.7 29 30 P00.8 AN0 12 11 AN8P00.9 31 32 P00.10 AN2 10 9 AN3

P00.11 33 34 P00.12 AN11 8 7 AN13AN19 35 36 AN18 AN20 6 5 AN21AN17 37 38 AN16 GND 4 3 GNDAN25 39 40 AN24 V_UC 2 1 (VCC_IN)

X102X103

+5,5V…+40V

GND




6.3 USB connector pinout

Figure 6-3 USB connector pinout (Micro USB B-type)

6.4 CAN connector pinout

Figure 6-4 CAN connector pinout (IDC10)

6.5 LIN connector pinout

Figure 6-5 LIN connector pinout (IDC10)

D+

D-

VC

C

GN

DID

2 4 6 8

GN

D

CA

NH

CAN

L

1 3 5 7 9

10

GN

D

2 4 6 8

GN

D

BUS

VIN

opt

1 3 5 7 9

10

GN

D




6.6 Ethernet connector pinout

Figure 6-6 Ethernet connector pinout (RJ45)

6.7 OCDS1 connector pinout

Figure 6-7 OCDS1 connector pinout (IDC16)

6.8 DAP connector pinout

Figure 6-8 DAP connector pinout (Samtec FTSH10)

J2J1 J3 J4 J5 J6 J7 J8

TDO

2 4 6 8

1 3 5 7 9

10 12 14 16

11 13 15

TDI

/TR

ST

TCK

TMS

GN

D

GN

D

/PO

RS

T

GN

D

V_U

C

DAP

0

2 4 6 8

1 3 5 7 9

10

/TR

ST

/PO

RS

T

DAP

2

DA

P1

GN

D

GN

D

Key

GN

D

V_U

C



Schematic and Layout

7 Schematic and Layout

7.1 Known problemsNo problems known.

7.2 Schematic




Figure 7-1 Schematic - Project Overview

11

22

33

44

55

66

77

88

DD

CC

BB

AA

4In

fine

on T

echn

olog

ies

AG

AT

VM

CA

CE

AT

VC

ES

Am

Cam

peon

1-12

D-8

5579

Neu

bibe

rgT

el.:

+49-

89-2

34-0

4

08.0

5.20

18

Num

ber:

Dat

e:

Shee

t:of

App

licat

ion

Kit

TC

3X7

Pro

ject

Ove

rvie

w

2.0

Rev

isio

n:

G:\Technical_Support\TriCore\TriBoard\EDA_DXP\ApplicationKit\ApplKitTC3X7\ApplKitTC3X7V2.X\ApplKitTC3X7V20.prj

File:

POR

T[0

0..3

4]

/ESR

0

/PO

RSTC

PU

and

Pow

er S

uppl

yC

PU_s

uppl

y.sc

h

POR

T[0

0..3

4]

/ESR

0

On

Boa

rd P

erip

hera

lsPe

riph

eral

s.sc

h

POR

T[0

0..3

4]

/PO

RST

Min

iWig

gler

and

DA

PO

CD

S.sc

h

/ESR

0

POR

T[0

0..3

4]

/PO

RST




Figure 7-2 Schematic - CPU and Power Supply

11

22

33

44

55

66

77

88

DD

CC

BB

AA

1In

fine

on T

echn

olog

ies

AG

AT

VM

CA

CE

AT

VC

ES

Am

Cam

peon

1-12

D-8

5579

Neu

bibe

rgT

el.:

+49-

89-2

34-0

4

08.0

5.20

18

Num

ber:

Dat

e:

Shee

t:of

App

licat

ion

Kit

TC

3X7

CP

U a

nd P

ower

Sup

ply

2.0

Rev

isio

n:

G:\Technical_Support\TriCore\TriBoard\EDA_DXP\ApplicationKit\ApplKitTC3X7\ApplKitTC3X7V2.X\CPU_supply.sch

File:

VD

D/V

DD

SBG

8

ESR

1G

16E

SR0

F16

POR

STG

17

VE

XT

A2

VE

XT

OSC

N20

VD

DG

13

VG

AT

E1N

(VC

AP0

)Y

17

VD

DO

SCN

19

XT

AL

1M

20X

TA

L2

M19

VSS

OSC

L20

VD

D/V

DD

SBH

7

VD

DH

14V

DD

N14

VD

DP1

3

VD

DN

7

VD

DP8

VE

XT

B3

VE

XT

W20

VE

XT

V19

VE

VR

SBT

11

VD

DP3

A19

VD

DP3

B18

VD

DD

16V

DD

E15

VFL

EX

(VE

XT

)D

5

VSS

B2

VSS

D4

VSS

E5

VSS

T16

VSS

U17

VSS

W19

VSS

Y20

VSS

A20

VSS

B19

VSS

D17

VSS

E16

VSS

/AG

BT

TX

0NP1

0

VSS

/AG

BT

TX

0PP1

1

VSS

P12

VSS

N9

VSS

P9

VSS

N10

VSS

N11

VSS

N12

VSS

M7

VSS

M8

VSS

M10

VSS

M11

VSS

M13

VSS

M14

VSS

/AG

BT

CL

KN

L7

VSS

L8

VSS

L9

VSS

L10

VSS

L11

VSS

L12

VSS

L13

VSS

/AG

BT

ER

RL

14

VSS

/AG

BT

CL

KP

K7

VSS

K8

VSS

K9

VSS

K10

VSS

K11

VSS

K12

VSS

K13

NC

/DA

PE0

K14

VSS

J7V

SSJ8

VSS

J10

VSS

J11

VSS

J13

VSS

J14

VSS

H9

VSS

H10

VSS

H11

VSS

H12

VSS

G9

VSS

/DA

PE2

G10

VSS

/DA

PE1

G11

VSS

G12

VG

AT

E1P

(VC

AP1

)W

17

U10

1A

TC

3X7

V_U

C

VD

D

CB

101

100n

CB

102

100n

CB

103

100n

GN

D

VD

D

VA

RE

F1

VD

DM

CB

110

3.3μ

F

GN

D

CB

111

390n

GN

D

CB

108

330n

GN

D

CB

107

330n

GN

D

CB

106

1μF

GN

D

R10

1

0R

C10

210

pF

C10

110

pF

1 2

Y10

120

MH

z

GN

D

GN

D

R11

64K

7

12

X10

1POWER

VC

C_I

N D10

1 MSS

2P2 C

114

100μ

F/40

VC

B11

210

0nG

ND

GN

D

V_P

RE

RE

GV

IN

GN

DV

IN

QST

N.C

.43

WD

I16

QST5

VS1

45

WA

K4

RSH

47

PG1

41N

.C.

44

VST

2

EN

A3

AG1 6

SW2

42

FRE

24

RO

T17

INT

18

SDO

13

SCL

14Q

UC

30

QC

O31

SYN

19

QT

133

QT

232

VC

I26

SEC

23

EV

C21

SCS

15

ER

R20

BSG

1R

SL48

STU

25

DR

G46

GND HS

SDI

12

SS1

11

SS2

10

QV

R29

AG2 7

AG3 8

AG4 28

AGS 9

TM

22

GST

27

PG2

40

N.C

.34

N.C

.35

N.C

.36

FB4

37

FB5

38

N.C. 39

C14

orne

wer

U10

2*

VR

EF_

5V

+5V

S102

WA

KE

R10

210

0R

S101

RE

SET

GN

D

R10

4

4K7

R10

510

KC

115

4,7μ

F/10

V

GN

DG

ND

V_U

CR

103

2K2

V_U

C

GN

D

GN

D

C10

8

1μF/

10V

GN

D

C11

3

4,7μ

F/10

V

GN

D

V_U

C

QT

1

QT

2

/ESR

0

GN

D

R11

5

100K

/PO

RST

GN

DX

11

VC

C10

SCK

8

VSS

5SI

6

MFP

9

X2

2V

BA

T3

CS

4

SO7

U10

4*

12

Y10

2

32.7

68H

zC

103

10pF

C10

412

pF

GN

DG

ND

CB

114

100n

1 3 5 7 9 11 13 15

2 4 6 8 10 12 14 1617 19 21 23 25 27 29

18 20 22 24 26 28 3031

3233

3435

3637

3839

40

X10

2

CO

N2X

20

1 3 5 7 9 11 13 15

2 4 6 8 10 12 14 1617 19 21 23 25 27 29

18 20 22 24 26 28 3031

3233

3435

3637

3839

40

X10

3

CO

N2X

20

R11

9*

GN

D

V_U

C D10

5L

PT

67K

GN

DR11

822

0R

R11

7

10K

V_U

C

1

3 2

Q10

6B

SS13

8N

D10

6L

ST

67K

1

3 2

Q10

3

BSS

138N

POR

T[0

0..3

4]

/PO

RST

R11

1

10K

R11

2

10K

/ESR

1

V_U

CV

IN_O

PT

GN

D

P23.

1

GN

D

V_U

CV

IN_O

PT

GN

DG

ND

P14.

2

+1

-2

LS1

01

BR

T16

15P-

06+5V

GN

D

R12

1

10K

R12

3

4R7_

opt

R12

2

4R7

VR

EF_

5V

GN

D

R13

410

K_o

pt

1

32

Q10

5B

SS83

P

GN

D

BT

101

BR

-122

5/V

CN

C11

6*

P14.

3

P14.2

C10

622μF

/10V

C10

9

4,7μ

F/10

VC

110

4,7μ

F/10

VC

111

4,7μ

F/10

VC

112

4,7μ

F/10

V

GN

D

GN

D

+3V

3R

124

1R

QST R11

010

0K

GN

DR

114

10K

P33.

8

P33.

7

R12

5

1R_o

ptVR

EF_

5V

+3V

3

1

3 2

Q10

2B

SS13

8N

D10

2

SS26

VD

D_U

SB

L10

1

XA

L50

50-2

23M

EB

L10

2

XA

L40

30-4

72M

EC

R13

0 250m

R

4

3

1,2,5,6

Q10

1B

SL60

6SN

C10

747μF

/40V

GN

D

GN

D

GN

D

D10

3

SS26

VIN

GN

D

P14.3

GN

DR14

22K

2_op

t

R12

70R R

128

20K

GN

D

+5VCB

113

100n

R12

9

470R

D10

4

LP

T67

KG

ND

13

D11

1

BA

T54

R13

61K C

118

100p

F

GN

D

P15.

8P1

5.6

P15.

7

R13

7

10K

P22.

3P2

2.0

P22.

1

R13

8 1KP3

3.9

R13

92K

2

GN

D

V_U

C

+3V

3

CB

104 1μ

FC

B10

5

100n

VD

D

C10

5*

GN

D

2

71

8

3

45 6

Q10

4*

GN

D

V_U

CL

103

*C

120

*

GN

D

GN

D

Q1

GND 6

SEN

SE/A

DJ

2

BY

P4

IN8

EN

5

GND HS

U10

3T

LS2

05B

0EJV

33

GN

D

V_U

CC

119

10μF

C11

710

nF

+3V

3

GN

D

R12

0

0R_o

pt

V_U

C+3

V3

P11.

6D

9

P11.

9A

9

P11.

3B

10

P11.

11A

8

P11.

12B

8

P11.

10B

9

P11.

2A

10

P02.

0B

1

P02.

1C

2

P02.

2C

1

P02.

3D

2

P02.

4D

1P0

2.5

E2

P00.

4J1

P00.

5J2

P00.

12L

2

P00.

9K

2

P00.

3H

2

P00.

0G

1

P10.

6/H

WC

FG5

A4

P13.

1A

12P1

3.0

B12

P13.

3A

11

P10.

1B

7

P13.

2B

11

P10.

5/H

WC

FG4

B5

P10.

2A

5

P10.

3A

6P0

0.2

H1

P00.

1G

2

P11.

8E

7

P00.

8K

4P0

0.7

K1

P00.

6J4

P02.

6E

1

P02.

7F2

P02.

8F1

P11.

4D

10

P11.

0E

10

P11.

1E

9

P11.

5D

8

P11.

7E

8

P11.

13E

6

P11.

14D

7P1

1.15

D6

P12.

0E

12

P12.

1E

11

P10.

4(N

C)

B6

P10.

0(N

C)

A7

P10.

7(N

C)

A3

P10.

8(N

C)

B4

P00.

10(N

C)

K5

P00.

11(N

C)

L1

P02.

9(N

C)

E4

P02.

10(N

C)

F5

P02.

11(N

C)

F4

P01.

3(N

C)

G5

P01.

4(N

C)

G4

P01.

5(N

C)

H5

P01.

6(N

C)

H4

P01.

7(N

C)

J5

U10

1B

TC

3X7

P15.

3B

17P1

5.2

C19

P15.

5E

14

P20.

10E

19

P20.

14C

20

P14.

1A

15P1

4.0

B16

P15.

1A

18P1

5.0

B20

P20.

11E

20

P20.

12D

19

P20.

13D

20

P20.

8F2

0

P20.

9E

17

P15.

4A

17

P20.

3G

20

P20.

6F1

7

P33.

5Y

12

P20.

7F1

9

P21.

3J1

9P2

1.2

K19

P33.

7Y

13

P22.

3R

19

P33.

8W

14

P33.

9Y

14

P33.

10W

15

P21.

4K

20

P33.

11Y

15

P21.

5J2

0

P20.

0H

20

P22.

0P2

0P2

2.1

P19

P22.

2R

20

P15.

8D

14P1

5.7

D15

P15.

6A

16

P33.

12W

16

P23.

1U

19

P33.

4W

12

P33.

6W

13

P14.

7D

13

P33.

3Y

11

P22.

4P1

6

P14.

8A

13

P33.

1Y

10P3

3.0

W10

P33.

2W

11

P33.

13(N

C)

Y16

P23.

0(N

C)

V20

P23.

2(N

C)

U20

P23.

4(N

C)

T20

P23.

3(N

C)

T19

P20.

1(N

C)

G19

P32.

3(N

C)

Y19

P32.

4(N

C)

W18

P32.

5(N

C)

T15

P32.

6(N

C)

U15

P32.

7(N

C)

U16

P23.

5(N

C)

T17

P23.

6(N

C)

R17

P23.

7(N

C)

R16

P33.

14(N

C)

T14

P33.

15(N

C)

U14

P21.

0(N

C)

K17

P21.

1(N

C)

J17

P22.

5P1

7

P22.

6(N

C)

N16

P22.

7(N

C)

N17

P22.

8(N

C)

M16

P22.

9(N

C)

M17

P22.

10(N

C)

L16

P22.

11(N

C)

L17

P14.

9(N

C)

D12

P14.

10(N

C)

D11

P34.

3(N

C)

U12

P34.

2(N

C)

T12

P34.

4(N

C)

T13

P34.

5(N

C)

U13

P34.

1(N

C)

U11

P14.

6B

13

P32.

2(N

C)

Y18

U10

1C

TC

3X7

P10.

1

P33.

12

P00.

0

AN

1(P

34.0

)U

10

AN

2(A

N0

/P40

.0)

W9

AN

27(A

N13

/P41

.1)

V1

AN

5(A

N1

/P40

.1)

Y9

AN

8(A

N2

/P40

.2)

W8

AN

10(A

N3

/P40

.3)

Y8

AN

11(A

N4

/P40

.4)

W7

AN

13(A

N5

/P40

.5)

W6

AN

16(A

N6

/P40

.6)

W5

AN

18(A

N7

/P40

.7)

W4

AN

20(A

N9

/P40

.9)

Y3

AN

21(A

N10

/P40

.10)

Y2

AN

37(A

N18

/P41

.6)

P2

AN

39(A

N19

/P41

.7)

P1

AN

44(A

N20

/P41

.8)

N1

AN

45(A

N21

/P41

.9)

N2

VSS

MY

7V

AR

EF1

(VA

RE

F)Y

6

VDDM Y5

VSSM Y4

AN

28(A

N14

/P41

.2)

U2

AN

29(A

N15

/P41

.3)

U1

AN

33(A

N16

/P41

.4)

R1

AN

35(A

N17

/P41

.5)

R2

AN

46(A

N22

/P41

.10)

M1

AN

47(A

N23

/P41

.11)

M2

AN

19(A

N8

/P40

.8)

W3

AN

25(A

N11

/P40

.11)

W1

AN

26(A

N12

/P41

.0)

V2

VSS

M(N

C)

T2

VA

RE

F2(N

C)

T1

AN

0(N

C)

T10

AN

3(N

C)

U9

AN

4(N

C)

T9

AN

6(N

C)

T8

AN

7(N

C)

U8

AN

9(N

C)

U7

AN

12(N

C)

T7

AN

14(N

C)

U6

AN

15(N

C)

T6

AN

22(N

C)

T5

AN

17(N

C)

U5

AN

23(N

C)

R5

AN

24(N

C)

W2

AN

30(N

C)

T4

AN

31(N

C)

R4

AN

32(N

C)

P4

AN

34(N

C)

P5

AN

36(N

C)

N4

AN

38(N

C)

N5

AN

40(A

N49

/NC

)M

5

AN

41(A

N48

/NC

)M

4

AN

42(N

C)

L5

AN

43(N

C)

L4

U10

1D

TC

3X7

AN

25(1

1)A

N1

VA

RE

F2

CB

109

3.3μ

F GN

D

VA

RE

F1

TR

STL

19

TC

K/D

AP0

J16

TM

S/D

AP1

K16

P21.

6/T

DI

H17

P21.

7/T

DO

/DA

P2H

16

P20.

2/T

EST

MO

DE

H19

P14.

3/H

WC

FG3_

BM

IB

14

P14.

4/H

WC

FG6_

HIG

HZ

B15

P14.

2/H

WC

FG2_

EV

R13

E13

P14.

5/H

WC

FG1_

EV

R33

A14

U10

1E

TC

3X7

P21.

6P2

1.7

DA

P1D

AP0

/TR

ST

P33.

0

/ESR1

/ESR0

/PORST

V_U

C

/PORST

/PO

RST

P14.5

R14

02K

2

GN

D

V_U

C

P14.4

GN

DR14

32K

2_op

t

R13

34K

7

P14.3

V_U

C

V_U

CR

106

* R10

7

* R10

8

* R10

9

*

D10

7 LB

T67

3D

108 L

BT

673

D10

9 LB

T67

3D

110 L

BT

673

P13.

3

P13.

2

P13.

1

P13.

0

AN

20(9

)A

N21

(10)

AN

8(2)

AN

2(0)

AN

27(1

3)A

N26

(12)

AN

0

P23.

0A

N1

P23.

1P3

4.1

P23.

2P3

4.2

P23.

3P3

4.3

P23.

4P2

2.4

R13

5

4R7_

opt

R12

6

4R7

VR

EF_

5V

+3V

3

VA

RE

F2

AN

16(6

)

R14

4*

AN

17(1

4)

AN

28(1

4)A

N3(

6)R

151

* AN

8(2)

AN

2

AN

5(1)

AN

29/4

4(15

)

AN

24(1

2)

AN

27(1

3)

AN

26(1

2)

AN

16(6

)

AN

17(1

4)A

N28

(14)

AN

24(1

2)

R15

0*A

N0

R14

5*A

N8(

1)R

153

*AN

5(1)

R15

2*A

N3(

6)

R15

4*

R15

5*A

N2(

0)

AN

16(6

)

R15

6*

R14

6* A

N16

(13)

P00.

1P0

0.2

P00.

3P0

0.4

P00.

5P0

0.6

P00.

7P0

0.8

P00.

9

P00.

12

P02.

0P0

2.1

P02.

2P0

2.3

P02.

4P0

2.5

P02.

6P0

2.7

P02.

8

P14.

0P1

4.1

P14.

7P1

4.8

P15.

0

P15.

2P1

5.3

P15.

4P1

5.5

P15.

6P1

5.7

P15.

8

P14.

2P1

4.3

P14.

4P1

4.5

P14.

6

P20.

0

P20.

6P2

0.7

P20.

8P2

0.9

P20.

12P2

0.13

P20.

14

P20.

3

P12.

0P1

2.1

P21.

4P2

1.5

P22.

0P2

2.1

P22.

2P2

2.3

P33.

0P3

3.1

P33.

2P3

3.3

P33.

4P3

3.5

P33.

6P3

3.7

P33.

8P3

3.9

P33.

10P3

3.11

P23.

1

P13.

0P1

3.1

P13.

2P1

3.3

P11.

12P1

1.11

P11.

10P1

1.9

P11.

6

P11.

3P1

1.2

P10.

2P1

0.3

P10.

5P1

0.6

R15

7*

R15

8*

R15

9*

R16

0*

R16

1*

P00.

11P0

0.10

P23.

0

P23.

2P2

3.3

P23.

4

P34.

1P3

4.2

P34.

3P2

2.4

XT

AL

2X

TA

L1

P10.

7

GN

D

R16

60R

05

VD

D

AN

11(4

)

AN

29/4

4(15

)

X1

1

VC

C8

SCL

6V

SS4

SDA

5M

FP7

X2

2V

BA

T3

U10

5*

QST

QST

MFP

MFP

VB

AT

P15.

5P1

5.4 R

147

2K

V_U

CR

148

2K

V_U

C

QST

C12

110μF

GN

D

P21.

3P2

1.2

5V 1K5

R10

6-10

9R

119

U10

23,

3VT

LF3

5584

QV

VS1

470R

V_U

CT

LF3

5584

QV

VS2

680R

100R

C12

247

nFG

ND

C12

347

nFG

ND

C12

447

nFG

ND

P33.

8

P33.

9P3

3.10

P33.

11

P02.

0P0

2.1

P02.

2P0

2.3

P02.

4P0

2.5

P02.

6P0

2.7

P02.

8P0

0.0

P00.

1P0

0.2

P00.

3P0

0.4

P00.

5P0

0.6

P00.

7P0

0.8

P00.

9P0

0.12

AN

21(1

0)A

N20

(9)

AN

8(1)

AN

25(1

1)

P22.

3P2

2.2

P22.

1P2

2.0

P15.

7P1

5.6

P33.

5

P15.

2

P14.

8P1

4.6

P14.

5

P20.

0

P21.

3

P33.

6

AN

24(1

2)P1

4.4

P33.

1P3

3.2

P33.

3P3

3.4

P23.

0P2

3.1

P23.

2P2

3.3

P23.

4

P00.

10P0

0.11

P33.

12

P14.

7

P15.

3P1

5.5

P15.

4

AN

17(1

4)A

N16

(13)

AN

0A

N2

P21.

2

P21.

4P2

1.5

P10.

8

P20.

10P2

0.11

P15.

1

R16

30R

R16

40R

C12

5op

t

AN

3(6)

AN

13(5

)

VD

DA

N13

(5)

AN

11(4

)

AN

18(7

)A

N19

(8)

AN

19(8

)A

N18

(7)

AN

29/4

4(15

)

R13

147

0R

R13

2

10K

V_U

C

P11.

0P1

1.1

P11.

4P1

1.5

P11.

7P1

1.8

TC

397B

TC

387

AU

RIX

2G1K N

A

TC

377

TC

367

TC

337

1KR

153-

R16

1N

A

NA

0RR

150-

R15

2R

144-

R14

6

Q10

4L

103

C10

5C

116

BSZ

15D

C02

KD

NA

22μF

LT

F502

2T-3

R3N

2R5

NA

NA

NA

1μF

4,7μ

F10μF

C12

0M

CP7

9511

-I/M

SN

AU

104

MC

P794

11-I

/MS

NA

U10

5

1 2

JP20

1op

t

R11

3

0R_o

pt

VIN

_OPT

VC

C_I

N




Figure 7-3 Schematic - On Board Peripherals

11

22

33

44

55

66

77

88

DD

CC

BB

AA

2In

fine

on T

echn

olog

ies

AG

AT

VM

CA

CE

AT

VC

ES

Am

Cam

peon

1-12

D-8

5579

Neu

bibe

rgT

el.:

+49-

89-2

34-0

4

08.0

5.20

18

Num

ber:

Dat

e:

Shee

t:of

App

licat

ion

Kit

TC

3X7

Per

iphe

rals

2.0

Rev

isio

n:

G:\Technical_Support\TriCore\TriBoard\EDA_DXP\ApplicationKit\ApplKitTC3X7\ApplKitTC3X7V2.X\Peripherals.sch

File:

+5V

R24

3

0R

GN

D

R24

612

0R

R24

5

0R R24

7

0RG

ND

2

RX

D4

CA

NH

7

TX

D1

VC

C3

CA

NL

6

STB

8

VIO

5U

206

TL

E92

51V

SJ

R24

40R

V_U

C

1 3 5 7 9

2 4 6 8 10

X20

2

CA

N0

GN

D

POR

T[0

0..3

4]

CB

221

100n

GN

D

POR

T[0

0..3

4]

GN

D

R24

2

0R

R24

01K

CB

220

100n

GN

D

C20

922μF

/40V

GN

DP1

0.5

P10.

6

13

2

D20

1

BA

T54

-04

1 3 5 7 9

2 4 6 8 10

X20

3

LIN

1

R24

1

10K

VIN

R23

9

0R_o

pt

GN

D

GN

D

V_U

C

VIN

VS

P20.

9

EN

2

INH

8

BU

S6

TX

D4

WK

3

RX

D1

VS

7G

ND

5U

205

TL

E72

59-3

GE

C21

01n

GN

D

DB

11

DB

22

DB

33

DB

44

GN

D5

VC

C6

CS

7

RS

8

WR

9

RD

10

IM0

11

X+

12

Y+

13

X-

14

Y-

15

LE

DA

16L

ED

K4

17

LE

DK

318

LE

DK

219

LE

DK

120

N.C

.21

DB

522

RST

31

VC

I32

VC

C33

GN

D34

DB

1023

DB

1124

DB

1225

DB

1326

DB

1427

DB

1528

DB

1629

DB

1730

DB

635

DB

736

DB

837

LC

D20

1

EL

T24

0320

AT

P

D15

D0

D1

D2

D3

D4

D5

D6

D7

D8

D9

D10

D11

D12

D13

D14

1

3 2

Q20

1B

SS13

8N

GN

D

GN

D+3

V3

+3V

3+3

V3

/CS_

TFT

/WR

/RD

R20

810

K

R20

7

470R

GN

D

X+

Y+

X-

Y-

+3V

3

GN

D

VC

C1

BU

SY13

PEN

IRQ

11

X+

2

GN

D6

VC

C10

Y+

3

X-

4

Y-

5

IN3

7

IN4

8

VR

EF

9

DO

UT

12D

IN14

CS

15

DC

LK

16

U20

2

AD

S784

3EC

B20

510

0nC

201

10uF

CB

204

100n

GN

D

V_U

C

GN

DG

ND

X+

Y+

X-

Y-

P20.

3P2

0.13

P20.

14P2

0.12

R20

322

RR

204

22R

R20

522

RR

206

22R

CB

206

100n

GN

D

RS

V_U

C

/ESR

0_3V

/LC

D16

/ESR

0

/ESR0_3V

/ESR

0_3V

P15.

0

VS

+3V

3

2

6 1

Q20

2AB

SD23

5N5

3 4

Q20

2BB

SD23

5N

GN

D

GN

DR21

010

K

R21

110

K

+3V

3

R20

9

10K

/ESR

0

R27

210

K_o

ptR

271

10KV

_UC

V_U

C

P20.

7

P20.

8

R25

7 *R

258 *

R26

9 *R

270 *

P10.

2

P10.

3

R20

11K

_opt

R20

20R

+3V

3

GN

D

IO1

40

IO2

41

IO3

42

IO4/

GC

K1

43

IO5/

GC

K2

44

IO6/

GC

K3

1

IO7

2

IO8

3

IO9

5

IO10

6

IO11

7

IO12

8

IO13

12

IO14

13

IO15

14

IO16

16

IO17

18

IO18

19IO

1920

IO20

21

VC

CIO

26

TD

I9

TM

S10

IO0

39

TC

K11

TD

O24

IO33

38

GN

D25

IO32

37

IO31

/GT

S136

IO30

/GT

S234

IO29

/GSR

33

IO28

32

IO27

31

IO26

30

IO25

29

IO24

28

IO23

27

IO22

23

IO21

22

VC

CIN

T35

VC

CIN

T15

GN

D17

GN

D4

U20

1

XC

9572

XL

-10V

Q44

I

CB

201

100n

CB

202

100n

CB

203

100n

+3V

3

GN

D

P20.

13

P20.

14P2

0.12

/LC

D16

P20.

6

D15

D7

D8

D9

D10

D11

D12

D13

D14

D6

D5

D4

D3

D2

D1

D0

/RD

/WR

RS

/CS_

TFT

1 32 4 5 6

X20

1

PRO

G_o

pt+3V

3

GN

D

/LC

D16

/ESR

0_3V

1 32 4 5 6 7 8 CO

MC

D

S

X20

5

MIC

RO

-SD

GN

D

VD

D_S

D

R23

8

*

C21

110

uF

GN

D

+3V

3

P10.

5P1

0.2

P10.

3P1

0.1

MR

ST_S

D

/CS_

SDM

TSR

_SD

SCL

K_S

D

/CD

_SD

/CD

_SD

P10.

7

R25

0

4R7

DA

T2

DA

T3

CM

D

CL

K

DA

T0

DA

T1

R25

1 *R

252 *

R25

3 *R

254 *

R26

5 *R

266 *

R26

7 *R

268 *

R25

5 *R

256 *

P20.

10P2

0.11

P15.

3P1

5.1

P20.

7P2

0.8

R26

1*

R26

2*

R26

3*

R26

4*

R24

9

*P0

2.0

99

22

44

33

55

66

88

LY

KL

YK

LY

AL

YA

LG

AL

GA

LG

KL

GK

SHIE

LD

S

77

SC10

C1

X20

4

RJ4

5

C20

4 27pF

C20

5 27pF

GN

D

GN

D

R22

722

R

1 3

Y20

1

NX

3225

SA-2

5MH

z

R22822R

R23

5

0RR

236

0RP1

2.0

P12.

1

R22

22K

49/1

%

GN

DG

ND

C20

3

4,7μ

F

GN

DG

ND

CB

208

100n

+1V

GN

DG

ND

GN

D

+3V

3

CLKOUT35

LE

D0

32

LE

D1

33

LE

D2

34

XT

AL

_IN

36

XT

AL

_OU

T37

EPA

DH

S

MD

IN0

2M

DIP

01

MDIO14

REG_OUT/LDO_OUT 30

INTB/PMEB31

MDC13

TXC20

PHY

RST

B12

RSE

T39

RT

L82

11F

TXD018 TXD117 TXD216 TXD315

RXD025 RXD124 RXD223 RXD322 RXCTL26

TXCTL19

RXC27

MD

IN1

5M

DIP

14

MD

IN2

7M

DIP

26

MD

IN3

10M

DIP

39

AVDD10 3

DVDD_RG 28

AVDD33 11

DVDD10 21

DVDD33 29

AVDD10 8AVDD10 38

AVDD33 40

U20

3R

TL

8211

F

GN

DR

224 51

0R

C21

7 10n

Shie

ld

GN

D

GN

D

+3V

3

GN

D

C21

3

100n

C21

4

100n

C21

5

100n

C21

6

100n

C21

2

1000

pF/2

KV

+3V

3R

221

4K7

R22

3

510R

C20

810

0p

GN

D

C20

6

100p

R22

64K

7R

225

4K7

C20

7

100p

MD

I0_P

MD

I0_N

MD

I1_P

MD

I1_N

MD

I2_P

MD

I2_N

MD

I3_P

MD

I3_N

L20

12,

2μH

/1A

CB

209

100n

CB

210

100n

CB

211

100n

CB

212

100n

CB

213

100n

CB

214

100n

CB

215

100n

CB

216

100n

C20

2

4,7μ

F

R27

4

opt

R27

3

4K7

GN

D

+3V

3

R23

4

22R

R23

04K

7R

237

*

P10.

8

+3V

3

R22

91K

5

+3V

3

C21

9

opt

GN

D

R27

6

4K7

R27

5

opt

R27

7

opt

R27

8

opt

R27

9

opt

R28

2

opt

R28

0

4K7

R28

1

4K7

R28

3

4K7

R28

4

4K7

C21

8

4,7μ

F

P11.

12

P11.

10P1

1.9

P11.

8P1

1.7

P11.

11

P11.

4

P11.

3P1

1.2

P11.

1P1

1.0

P11.

6R

233

22R

RN

202

22R

R23

222

R

C22

0op

t

GN

D

/ESR

0_3V

R24

8

*

P11.

5

P02.

1

TC

397B

R26

1-R

270

R25

1-R

258

TC

387

0R

AU

RIX

2GT

C37

7 0R

TC

367

TC

337

R24

90R

0RR

238

R24

8R

237

330R

NA

NA

NA

NA

NA

NA

330R

RN201

22R

TC

397B

V_U

C3,

3V5V

AN

YA

NY

AN

Y3,

3V




Figure 7-4 Schematic - miniWiggler JDS and Debug connectors

11

22

33

44

55

66

77

88

DD

CC

BB

AA

3In

fine

on T

echn

olog

ies

AG

AT

VM

CA

CE

AT

VC

ES

Am

Cam

peon

1-12

D-8

5579

Neu

bibe

rgT

el.:

+49-

89-2

34-0

4

08.0

5.20

18

Num

ber:

Dat

e:

Shee

t:of

App

licat

ion

Kit

TC

3X7

OC

DS

and

OnB

oard

Wig

gler

2.0

Rev

isio

n:

G:\Technical_Support\TriCore\TriBoard\EDA_DXP\ApplicationKit\ApplKitTC3X7\ApplKitTC3X7V2.X\OCDS.sch

File:

TM

S1

TD

O3

CPU

CL

OC

K5

TD

I7

TR

ST9

TC

K11

BR

KIN

13

N.C

.15

VC

C2

GN

D4

GN

D6

POR

ST8

BR

KO

UT

10

GN

D12

OC

DSE

14

KE

Y16

X30

1

OC

DS1

V_U

C

GN

D

DAP0

DAP1

/TRST

GN

D

/PO

RST

POR

T[0

0..3

4]

/PO

RST

POR

T[0

0..3

4]

EE

CS

63

EE

CL

K62

EE

DA

TA

61

TE

ST13

SUSP

EN

D36

OSC

I2

DM

7

GND 1

VR

EGO

UT

49

RE

SET

14

AGND 10

OSC

O3

DP

8

RE

F6

GND 5

VR

EG

IN50

GND 11

VCCIO20

GND 15

VCCIO31

AD

BU

S016

AD

BU

S117

AD

BU

S218

AD

BU

S319

AD

BU

S421

AD

BU

S522

AD

BU

S623

AD

BU

S724

AC

BU

S026

AC

BU

S127

AC

BU

S228

BD

BU

S038

BC

BU

S048

BD

BU

S139

BC

BU

S152

BD

BU

S240

BC

BU

S253

BD

BU

S341

BD

BU

S443

BD

BU

S544

BD

BU

S645

BD

BU

S746

AC

BU

S329

AC

BU

S430

AC

BU

S532

AC

BU

S633

AC

BU

S734

BC

BU

S354

BC

BU

S455

BC

BU

S557

BC

BU

S658

BC

BU

S759

GND 25

GND 35

GND 47

GND 51

PWR

EN

60

VCORE64

VCORE12

VCORE37

VCCIO42

VCCIO56

VPLL9

VPHY4

U30

1

FT22

32H

L

VB

US

1

D+

3D

-2

ID4

GN

D5

BU

301

Mic

roU

SB

GN

D

R30

2

27R

R30

3

27R

R30

4

12K

/1%

C30

6

3,3u

F

VD

D_F

T

L30

1

MM

Z16

08R

300A

CB

301

100n

GN

D

R30

1

1K

CB

303

100n

CB

302

100n

CB

304

100n

C30

110μ/

6V

GN

D

VD

D_F

T

R30

5

10K

R30

7

opt

R30

6

2K2

CB

306

100n

R30

8

1K_o

pt

CB

307

100n

GN

D

V_U

C

AD

BU

S0A

DB

US1

AD

BU

S2A

DB

US3

AD

BU

S4A

DB

US5

AD

BU

S6A

DB

US7

AC

BU

S0A

CB

US1

AC

BU

S3

R30

910

K

V_U

C

TM

S

/TR

ST

DA

P0

USR

0

/RE

SET

D30

1L

BT

673

R31

110

0R

VD

D_F

T

/PO

RST

AD

BU

S0A

DB

US1

AD

BU

S2

AD

BU

S3

AD

BU

S4

AD

BU

S6/T

RST

_IN

AC

BU

S1A

CB

US5

BD

BU

S0B

DB

US1

USR

8

GN

D

P14.

0

R32

04K

7

V_U

C

DA

P1T

DI

/TR

ST

DA

P0

DA

P1

P14.1

P14.0

BD

BU

S0

BD

BU

S1

CB

309

100n

R31

268

0RD30

2L

PT

67K

VD

D_F

T

VD

D_F

TR

314

4K7

R31

610

K

R31

8

10K

R31

710

K R31

9

10K

VD

D_F

TV

_UC

VD

D_F

TV

_UC

R31

510

K

V_U

C

R31

010

K

VD

D_F

T

R32

1op

tR

322

opt

GN

DG

ND

GN

D

GN

D

1 3

Y30

1N

X32

25SA

-12M

Hz

C30

4 8pF

C30

5 8pF

VD

D_F

T

GN

D

GN

D

R32

4

10K

VD

D_F

T

GN

D

VD

D_F

T

VD

D_F

T

R32

5

10K

OU

T3

GND 2

IN1

U30

5T

LE

4274

GSV

33

GN

D

GN

D

CB

311

100n

CB

310

100n

CB

312

100n

GN

D

GN

D

C30

24u

7/6V

GN

D

CB

305

100n

VD

D_F

T

GN

D

L30

2

MM

Z16

08R

300A

C30

34u

7/6V

GN

D

CB

313

100n

GN

D

GN

D

VD

D_F

T

VD

D_F

T

+1V

8

/OE

1V

CC

5

A2

GN

D3

Y4

U30

4

74L

VC

1G12

5

CB

308

100n

GN

D

VD

D_F

T

GN

D

AC

BU

S4

AD

BU

S1

AD

BU

S2

R32

610

K

VD

D_F

T

CB

315

100n

CB

314

100n

GN

D

VD

D_F

TV

_UC

GN

DR

327

4K7

GN

D

AD

BU

S2

AC

BU

S3

DIR

5

VC

CA

1V

CC

B6

A3

GN

D2

B4

U30

6

SN74

LV

C1T

45D

BV

DIR

5

VC

CA

1V

CC

B6

A3

GN

D2

B4

U30

7

SN74

LV

C1T

45D

BV

CB

317

100n

CB

316

100nV

DD

_FT

V_U

C

GN

DR

328

4K7

GN

D

GN

D

AC

BU

S5

GN

D

AD

BU

S1

AC

BU

S5

AC

BU

S5A

CB

US4

P21.

7

P21.7

P21.6

P21.

6

AC

BU

S7

AC

BU

S7

AC

BU

S7A

CB

US3

R31

3

10K

R32

90R

_opt

R33

00R

_opt

AC

BU

S4

OR

G6

DN

C7

VC

C8

CS

1

GN

D5

Q4

CL

K2

D3

U30

2

93L

C46

B-I

/SN

G1

1A1

21Y

118

1A2

41Y

216

1A3

61Y

314

1A4

81Y

412

VC

C20

GN

D10

2Y1

9

2Y2

7

2Y3

5

2Y4

3

G19

2A1

11

2A2

13

2A3

15

2A4

17

U30

3

SN74

AH

C24

4PW

R33

6

0R

P21.

6

R33

5

0R

P21.

7R

332

0R_o

pt

R32

3

0R_o

pt

FOR

USI

NG

WIG

GL

ER

WIT

HJT

AG

:A

ssem

ble

R32

9-R

332

and

R30

8R

emov

eR

333-

R33

6

2

61

Q30

1AB

SD23

5N

5

34

Q30

1BB

SD23

5N

2

61

Q30

2AB

SD23

5N

5

34

Q30

2BB

SD23

5N

2

61

Q30

3AB

SD23

5N

5

34

Q30

3BB

SD23

5N

VD

D_U

SB

/PORST

R33

10R

_opt

R33

40R

AC

BU

S2

VR

EF

1G

ND

3

GN

D5

KE

Y7

GN

D9

DA

P12

DA

P04

USE

R1

8U

SER

06

RE

SET

10

X30

2

DA

P

V_U

C

DAP0

/TRST

DAP1

P21.7

/PO

RST

GN

D

13

D30

3

BA

T54




7.3 Layout

Figure 7-5 Component Plot Top Layer

U101

Y201

U203

RN202

RN20

1

R248R237

R23

6R235

R233

R232

R230

R22

9

R22

8R22

7

R222

L201

JP20

1

CB21

6CB21

5

CB214

C218

C205

C20

4

C20

2

D303

R164 R163

C125

R270

R269

R26

8

R267

R26

6

R265

R264R263 R262R261

R25

8R25

7

R256

R25

5

R254R253

R25

2

R25

1R23

8

R166C105

C120

L103

Q104

C11

6

C121

C124C123

C122

R14

8

R14

7U10

5

CB113

R12

8

R127

R115

R130

R134

BT101

U104

C117

U201

CB203

R20

4R205

R211

X203

R241

R239

R210

R208

D201

C20

9

U307

U306

R33

6

R328

R327

R313

CB317 CB316

CB315 CB314

D301

R32

3

CB305

C302

R311

BU301

L301

D302

R30

1

CB301

R308

U301

Y30

1

Q30

3

Q30

2

Q301

R31

2

R32

0

R31

4

R319

R318

R31

7R316

R315

R31

0

R30

3R30

2

CB302

R24

3

R24

4

R245 R247

CB206R20

1

R246

CB2

05R20

3

U206

R20

2

C201

R20

6

R20

7

CB204

R249

X201

X301

U202

CB202

C101

C10

2

C103

C10

4

C106

C107

C109

C110

C108

C114

CB101

CB102

CB1

03

CB110CB111

CB108

CB1

07

CB106

CB112

CB1

14

CB20

1

L101

L102

LS10

1

Q10

6

Q20

1

R101

R10

2R10

3

R106

R107

R108

R109

R111R112

R114

R116

R11

7R12

0

R122R123

R124

R125

U10

2X1

01

X102

X103X205

Y101

Y102R20

9

X202

R272

X302

R271

R142

R13

8

C119

CB104

CB10

9

Q202

R126

R14

0

R143

R14

4

R145

R14

6

R150

R151

R15

3

R15

2

R15

4

R155

R156

R157R158

R159R160

R161

U103

CB10

5

R133

R135

R132

X204




Figure 7-6 Component Plot Bottom Layer

R113

LCD201

R284

R283

R282

R281

R280

R279

R278

R277

R276

R275

R274

R273

R234

R226

R225

R224

R223

R221

CB213

CB212

CB211

CB210

CB209 CB208C220

C219

C217C216

C215

C214

C213

C212

C208

C207

C206

C203

R137

R136

D111

C118

Q105

R250

D103

D102

U205R242

R240

CB220

C210

R332R335

R334

R331

R330

R329

R326

U305

L302

CB313

C303

R304

C301

R325

R324

CB312

CB311

CB310

C305

C304

R322

R321

U304U303

C306

R309

CB309

CB308CB307

CB303

R307

U302

R306

R305

CB306

CB304

CB221

C211

C112

C113

C115

D101

D105

D106

D107

D108

D109

D110

Q101

Q102

Q103

R104R105

R110

R118

R119

R121

S101

S102

C111

D104R129

R139

R131




7.4 Layout with DimensioningThe following dimensions should be used for development of extension boards.

Figure 7-7 Dimensioning (mm)

U101

Y201

U203

RN202

RN201

R248R237

R236

R235

R233

R232

R230

R229

R22

8R227

R222

L201

JP201

CB216

CB2

15

CB214

C218

C205

C204

C202

D303

R164 R163

C125

R270

R269

R268

R267

R26

6

R265

R264R263 R262R261

R25

8R257

R256

R255

R254R253

R252

R251

R238

R166C105

C120

L103

Q104

C116

C121

C124C123

C122

R148

R147

U10

5

CB113

R128

R127

R115

R 130

R134

BT101

U10

4

C117

U201

CB203

R20

4R20

5

R211

X203

R241

R239

R21

0

R208

D201

C209

U307

U306

R336

R328

R327

R313

CB317 CB316

CB315 CB314

D301

R323

CB305

C302

R311

BU301

L301

D302

R301

CB301

R308

U301

Y301

Q30

3

Q30

2

Q301

R31

2

R320

R31

4

R319

R318

R317

R31

6

R315

R31

0

R303

R302

CB302

R243

R244

R245 R247

CB206

R201

R246

CB2

05R20

3

U206

R20

2

C201

R20

6

R207

CB204

R249

X201

X301

U202

CB2

02

C10

1C102

C103

C104

C106

C107

C109

C110

C108

C114

CB101

CB102

CB103

CB110CB111

CB108

CB107

CB106

CB112

CB114

CB201

L101

L102

LS101

Q106

Q201

R101

R102

R103

R106

R107

R108

R109

R111R112

R114

R116

R117

R120

R122R123

R124

R12

5

U102

X101

X102

X103

X205

Y101

Y102

R209

X202

R272

X302

R271

R142

R13

8

C119

CB104

CB1

09

Q202

R126

R14

0

R143

R144

R145

R146

R15

0

R151

R153

R15

2

R154

R155

R156

R157R158

R159R160R161

U103

CB105

R133

R135

R132

X204




Figure 7-8 Dimensioning (mil)

The dimensioning is valid for all Application Kits.

U101

Y201

U203

RN202

RN2

01R248R237

R236

R23

5

R233

R232

R230

R229

R22

8R227

R222

L201

JP201

CB2

16CB2

15

CB214

C218

C205

C20

4

C202

D303

R164 R163

C125

R270

R269

R268

R267

R266

R265

R264R263 R262R261

R258

R25

7

R256

R25

5

R254R253

R252

R251

R238

R166C105

C120

L103

Q104

C116

C121

C124C123

C122

R14

8

R14

7U105

CB113

R128

R127

R115

R130

R134

BT101

U10

4

C117

U201

CB203

R204

R205

R211

X203

R241

R239R21

0

R208

D201

C209

U307

U306

R336

R328

R327

R313

CB317 CB316

CB315 CB314

D301

R323

CB305

C302

R311

BU301

L301

D302R301

CB301

R308

U301

Y301

Q30

3

Q302

Q301R312

R320

R314

R319

R318

R317

R316

R315

R310

R303

R302

CB302

R243

R244

R245 R247

CB206

R201

R246

CB205R203

U20

6

R202

C20

1

R206

R207

CB204

R249

X201

X301

U202

CB2

02

C101

C102

C103

C104

C106

C107

C109

C110

C108

C114

CB101

CB102

CB1

03

CB110CB111

CB108

CB107

CB1

06

CB112

CB1

14

CB2

01

L101

L102

LS101

Q106

Q201

R101

R102

R103

R106

R107

R108

R109

R111R112

R114

R116

R117

R120

R122R123

R124

R125

U102

X101

X102

X103

X205

Y101

Y102

R209

X202

R272

X302

R27

1

R142

R138

C119

CB104

CB1

09

Q202

R126

R14

0

R143

R144

R145

R146

R150

R151

R153

R152

R154

R15

5R156

R157R158R159

R160R161

U103

CB1

05

R133

R135

R132

X204

User Manual RevisionHistory-1 V2.0 Application Kit TC3X7 V2.0 2018-06


Revision History

Page or Item Subjects (major changes since previous revision)

V2.0, 2018-06

all Adapt to new board version V2.0 with Gigabit Ethernet

Trademarks of Infineon Technologies AGµHVIC™, µIPM™, µPFC™, AU-ConvertIR™, AURIX™, C166™, CanPAK™, CIPOS™, CIPURSE™, CoolDP™, CoolGaN™, COOLiR™, CoolMOS™, CoolSET™, CoolSiC™,DAVE™, DI-POL™, DirectFET™, DrBlade™, EasyPIM™, EconoBRIDGE™, EconoDUAL™, EconoPACK™, EconoPIM™, EiceDRIVER™, eupec™, FCOS™, GaNpowIR™,HEXFET™, HITFET™, HybridPACK™, iMOTION™, IRAM™, ISOFACE™, IsoPACK™, LEDrivIR™, LITIX™, MIPAQ™, ModSTACK™, my-d™, NovalithIC™, OPTIGA™,OptiMOS™, ORIGA™, PowIRaudio™, PowIRStage™, PrimePACK™, PrimeSTACK™, PROFET™, PRO-SIL™, RASIC™, REAL3™, SmartLEWIS™, SOLID FLASH™,SPOC™, StrongIRFET™, SupIRBuck™, TEMPFET™, TRENCHSTOP™, TriCore™, UHVIC™, XHP™, XMC™.

Trademarks updated November 2015

Other TrademarksAll referenced product or service names and trademarks are the property of their respective owners.

Edition 2018-06Published by Infineon Technologies AG81726 Munich, Germany

© 2018 Infineon Technologies AG.All Rights Reserved.

Do you have a question about any aspect of this document?Email: [email protected]

Document referenceDoc_Number

IMPORTANT NOTICEThe information given in this document shall in noevent be regarded as a guarantee of conditions orcharacteristics ("Beschaffenheitsgarantie"). With respect to any examples, hints or any typicalvalues stated herein and/or any information regardingthe application of the product, Infineon Technologieshereby disclaims any and all warranties and liabilitiesof any kind, including without limitation warranties ofnon-infringement of intellectual property rights of anythird party. In addition, any information given in this document issubject to customer's compliance with its obligationsstated in this document and any applicable legalrequirements, norms and standards concerningcustomer's products and any use of the product ofInfineon Technologies in customer's applications. The data contained in this document is exclusivelyintended for technically trained staff. It is theresponsibility of customer's technical departments toevaluate the suitability of the product for the intendedapplication and the completeness of the productinformation given in this document with respect tosuch application.

For further information on technology, delivery termsand conditions and prices, please contact the nearestInfineon Technologies Office (www.infineon.com).

WARNINGS

Due to technical requirements products may containdangerous substances. For information on the typesin question please contact your nearest InfineonTechnologies office.

Except as otherwise explicitly approved by InfineonTechnologies in a written document signed byauthorized representatives of Infineon Technologies,Infineon Technologies’ products may not be used inany applications where a failure of the product or anyconsequences of the use thereof can reasonably beexpected to result in personal injury.

Please read the Important Notice and Warnings at the end of this document

mailto:[email protected]

http://www.infineon.com

Application Kit Manual TC3X7 V2 - Mouser...User Manual 2-1 V2.0 Application Kit TC3X7 V2.0 2018-06...

Documents

Transcript of Application Kit Manual TC3X7 V2 - Mouser...User Manual 2-1 V2.0 Application Kit TC3X7 V2.0 2018-06...