ANTARES - C · The ventilation unit with an incorporated active cooling circuit, ANTARES - C, in...
Transcript of ANTARES - C · The ventilation unit with an incorporated active cooling circuit, ANTARES - C, in...
-
ANTARES - C
-
FIELD OF APPLICATION
ANTARES - C
ANTARES C
0 100 120 140 180 200 220 240 280 300 320 340 380
Roof Top for indoor plug-in air conditioning
3
AN
TAR
ES C
-
ANTARES C
4
EXTRACT AIR
FRESH AIR
SUPPLY AIR
EXHAUST AIR
Compressor
Evaporator
Condenser
→→
→
The ventilation unit with an incorporated active cooling circuit, ANTARES - C, in addition to promoting healthy ventilation inside the rooms, supplies air at a temperature up to 8°C lower than the outside temperature.
The unit consists of:
• Ventilation unit with high-performance supply and return plug fan fans for nominal volumetric flow rates of 120 m3/h and head of 50 Pa, with the possibility of reaching up to 280 m3/h, with reduced energy consumption thanks to the electronically controlled motors.
• Module with active cooling circuit equipped with horizontal compressor to limit the height of the space
The machine does not need to drain condensate as it is vaporized in the expelled air.Recommended unit for the booths with a total volume of 15 m3 The air flow can go from a minimum of 120 m3/h to a maximum of 240 m3/h with a set point that can be set from 21°C to 25°C.
The air distribution must be as uniform as possible inside the box with a careful choice of diffusers and the use of insulated channels to avoid condensation.It is recommended to limit number of bends in the air distribution duct work in order to maintain cooling performance levels and contain the pressure drop and consequently the noise levels.For the installation, it is recommended to use some type of damper/vibration absorbers (installer care) to avoid direct contact between the unit sheet metal and the room structure which may result in transmission of noise and/or vibrations.
-
AN
TAR
ES C
DIMENSIONAL
DimensionLunghezza (A) [mm] 940
Larghezza (B) [mm] 940
Altezza (C) [mm] 170
Peso [kg] 63
5
-
TECHNICAL DATA SHEET
6
Technical and dimensional data ANTARES - C
Supply connection 2xDN125
Extract connection 2xDN125
Fans
Nominal Air flow m3/h 120
Power input [W] 200
Current consumption [A] 1,9
Supply voltage [V/Ph/Hz] 230/1/50
Compressor
Supply voltage [V/Ph/Hz] 230/1/50
Cooling powercon T
est=22°C, U
r= 50%, T
mand= 14°C, U
r= 66%
[W] 690
Power input, at nominal operating point [W] 253
Absorption at nominal operating point [A] 1,12
Power input, max [W] 310
Current consumption, max [A] 2,0
Refrigerant fluid [-] R134a
Condensation water dissipater
Power input [W] 1270
Current absorption [A] 5
General data
Total power input, max [W] 1780
Total absorption at nominal operating point [A] 8,9
Average current absorption [A] 4
Noise data
Sound pressure level in free field,1m distance flow rate 120 m3/h, ducted unit
[dB(A)] 45
-
SUPPLY AIR FLOW
EXHAUST SUPPLY AIR
EXTERNAL AIR FLOW
EXHAUST AIR FLOW
SUPPLY AIR FLOW
EXHAUST AIR FLOW
FIL
TE
RF
ILT
ER
EXAMPLE OF THE MACHINE INSTALLED
MACHINE LAYOUT
AN
TAR
ES C
7
-
NOTE: AS AN ALTERNATIVE TO THE SIMPLIFIED DISPLAY
DESCRIPTION
Evolution display + Bluetooth
Evolution display and transmitter Temperature + Humidity,without Bluetooth
Evoltion display and transmitter Temperature + Humidity + Bluetooth
EPJ COLOR touch screen
NOTE: THE STANDARD UNIT IS ALREADY EQUIPPED WITH:
DESCRIPTION
Controller
Cable
Easy display
ACCESSORIES
AN
TAR
ES C
9
-
ACCESSORIES
60600244
It is a sanitization and decontamination module with cold plasma technology, for the purification and decontamination of the aeraulic ducts, specially designed to be easily installed wherever you want to prevent or eliminate the formation of bacterial colonies on the duct surfaces.The sanitization technology developed for the medical sector is a simple and essential module that is made available for residential environments and is designed for the integrated management of VMC systems. The control and functions can be controlled remotely by the system heat recovery unit.
The main features of the AERONIX module are:• High efficiency: reduction of microbial load and volatile organic compounds up to 99%;• Low energy consumption: from 20VA;• Strong deodorant action: eliminates odors from the air in transit;• Natural process: does not use or produce residual chemicals
It can be used in any type of VMC system (Controlled Mechanical Ventilation) thanks to the simple installation in the distribution boxes for an air flow rate of up to 500 m3/h. The operation can be continuous or in cycles, depending on the connection.
10
COMPONENT DESCRIPTION
Wall mounting tab Electrical socket with fuse holder
Electrical part container Input connector and serial signal
Ionizing tube Out put connector for alarm signaling
Condenser activation bracket Illuminated ON / OFF switch
EBOX fixing holes
-
ACCESSORIES
60140028
The CO2 sensor detects gas concentrations due to human respiration in commercial and residential air-conditioned
environments.Provides the control with a proportional signal to manage the recirculation of the external air fans when necessary, thus contributing to the energy efficiency of the climatio control of buildings, and ensuring good air quality for people who stay in the environment (e.g. shopping malls, shops, theaters, offices).
AN
TAR
ES C
11
TECHNICAL DATA
Voltage supply 24 V AC / DC (± 10%)
Absorbed power
-
ACCESSORIES
The ducts and fittings of the PLAST line can be used in all residential ventilation systems, both in single flow systems and in dual flow systems with heat recovery.They represent the ideal solution in environments with reduced installation spaces, both in individual homes and in collective systems.The fittings are simple to assemble to the ducts and are equipped with a gasket which guarantees a class D seal.The mechanical seal is guaranteed by the fixing clips placed on the ends of the fittings.
Upon request, PLAST is available in a version with antibacterial treatment.
ADVANTAGES
• Ducts with a height of only 55 mm, suitable for installation in a false ceiling = reduced size
• Low pressure drops compared to flexible conduits
• Rigid ducts = greater impact resistance
• Simple assembly with reduced installation times
• All accessories are equipped with sealing gaskets = class D aeraulic seal
TECHNICAL FEATURES
• Fire reaction: self-extinguishing not classified
• Maximum operating temperature: + 80 ° C
• Thermal conductivity: 0.0544 - 0.0662 W / m ° C
Equivalent circular diameter: - rectangular duct 55 x 100 mm: ø 80 x 100 mm - rectangular duct 55 x 220 mm: ø 125 r
Recommended courses - For a rectangular duct 55 x 100 mm average: 50 m3/h (v = 2.5 m / s) max: 90 m3/h (v = 4.0 m / s) - For a rectangular duct 55 x 220 mm average: 100 m3/h (v = 2.5 m / s) max: 180 m3/h (v = 4.0 m / s)
50400031 Vertical curve at 90 °
50400030 Junction R/C
50400027Junction
50400035 Collar50400024
Conducted
12
-
50
40
00
28
Rac
cord
o o
rizz
on
tale
m
asch
io r
ect.
/cir
c.
55
x22
0-1
25
50
40
00
26
Co
nd
ott
o s
ilen
ziat
o
con
att
acco
mas
chio
, 5
5x2
20
x10
00
50
40
00
32
Cu
rva
ori
zzo
nta
le a
90
°, 5
5x2
20
50
40
00
38
Co
nd
ott
o s
ilen
ziat
o
con
att
acco
mas
chio
, 5
5x2
20
x50
05
04
00
02
4C
on
do
tto
ret
tan
gola
re
in P
VC
, 55
x22
0
50
40
00
23
Val
vola
bo
rea
12
5
50
40
00
51
Tub
o P
VC
12
55
04
00
02
9R
acco
rdo
ver
tica
le
mas
chio
rec
t./c
irc.
5
5x2
20
-12
5
È p
oss
ibile
sce
glie
re a
ltri
co
dic
ip
er c
on
figu
razi
on
i per
son
aliz
zate
CA
NA
LIZ
ZA
ZIO
NE
STA
ND
AR
D
Dev
on
o e
sser
e ta
glia
ti a
m
isu
ra d
a p
arte
del
l’uti
lizza
tore
NO
TE
13
-
50400024
TYPEA B C Pressure drop (Pa)
mm mm mm 54 m3/h 108 m3/h 216 m3/h
50400024 - 110 55 110 3000 1,5 3,1 6,1
50400024 - 220 55 220 3000 0,7 1,3 2,7
RECTANGULAR DUCT IN PVC
50400027HORIZONTAL MALE CONNECTION RECT./RECT.
TYPEA B C Pressure drop (Pa)
mm mm mm 54 m3/h 108 m3/h 216 m3/h
50400027 - 110 55 110 109 0,2 0,5 1,0
50400027 - 220 55 220 120 0,1 0,2 0,5
14
TO BE INSTALLED ONLY ON THE EXTRACT AIR
TO BE INSTALLED ONLY ON THE EXTRACT AIR
-
50400028HORIZONTAL MALE CONNECTION RECT./CIRC.
TYPEA B C D Pressure drop (Pa)
mm mm mm mm 54 m3/h 108 m3/h 216 m3/h
50400028 - 110 100 110 55 210 2,3 4,5 9,1
50400028 - 220 125 220 55 328 0,3 0,7 1,4
50400029MALE ELBOW BEND WITH ROTATING OFFSET SPIGOT RECT./CIRC.
TYPEA B C D Pressure drop (Pa)
mm mm mm mm 54 m3/h 108 m3/h 216 m3/h
50400029 - 110 100 110 55 165 7,4 14,7 29,5
50400029 - 220 125 220 55 195 3,6 7,3 14,5 AN
TAR
ES C
15
TO BE INSTALLED ONLY ON THE EXTRACT AIR
TO BE INSTALLED ONLY ON THE EXTRACT AIR
-
50400031VERTICAL BEND 90°
TIPOA B C Pressure drop (Pa)
mm mm mm 54 m3/h 108 m3/h 216 m3/h
50400031 - 110 55 110 120 6,1 12,2 24,3
50400031 - 220 55 220 165 2,5 5,0 9,9
50400032HORIZONTAL BEND 90°
TIPOA B C Pressure drop (Pa)
mm mm mm 54 m3/h 108 m3/h 216 m3/h
50400032 - 110 55 110 170 8,6 17,2 34,4
50400032 - 220 55 220 310 4,2 8,4 16,8
16
TO BE INSTALLED ONLY ON THE EXTRACT AIR
TO BE INSTALLED ONLY ON THE EXTRACT AIR
-
50400033FLEXIBLE BEND
TIPOA B C Pressure drop (Pa)
mm mm mm 54 m3/h 108 m3/h 216 m3/h
50400033 - 110 55 110 540 19,0 38,0 76,1
50400033 - 220 55 220 540 6,2 12,4 24,8
50400026SILENCED DUCT WITH MALE CONNECTION
TIPOA B C
mm mm mm
50400026 - 220 55 220 1000
Sound pressure level
63 HZ 125 HZ 250 HZ 500 HZ 1 kHz 2 kHz 4 kHz 8 kHz
-1 0 11 12 13 37 23 15
AN
TAR
ES C
17
TO BE INSTALLED ONLY ON THE EXTRACT AIR
TO BE INSTALLED ONLY ON THE EXTRACT AIR
-
50400038SILENCED DUCT WITH MALE CONNECTION
Sound pressure level
63 HZ 125 HZ 250 HZ 500 HZ 1 kHz 2 kHz 4 kHz 8 kHz
-1 -3 5 6 12 18 12 9
TYPEA B C
mm mm mm
50400038 - 220 55 220 500
50400051PVC PIPE
TYPE ø LONG.(mm)
50400051 - 100 100 1000
50400051 - 125 125 1000
18
TO BE INSTALLED ONLY ON THE EXTRACT AIR
TO BE INSTALLED ONLY ON THE EXTRACT AIR
-
50400023DIFFUSOR PCA 125
MODELø D1(mm)
ø D2(mm)
Hmin(mm)
Hmax(mm)
50400023 - 80 74 110 9 20
50400023 - 125 119 165 12 24
Diffusers in galvanized steel powder coated.The diffusers are suitable for both delivery and recovery, depending on the particular geometry of the diffusers themselves.The front of the diffusers can be removed to allow cleaning of the interior components or to access the channel.
50400040FLEXIBLE SOUND ABSORPTION PIPE
Diameterø
Package m
Dim. conf.mm
127 10 205x205x1100
AN
TAR
ES C
19
TO BE INSTALLED ONLY ON THE EXTRACT AIR
TO BE INSTALLED ONLY ON THE EXTRACT AIR Sound absorbing duct consisting of a harmonic steel spiral wrapped in a 74µm micro-perforated
aluminium/polyester laminate.Insulated fibreglass mattress density 18 kg/m3 and
thickness 25 mm.
External coverAluminum/polyester 49µm.
- Reaction to fire: class 1-1- Certificate: CSI 0104/04/RF
- Approval PD2229C0D-10003
Characteristics
Reaction to fire Class 1
Duct aluminium/polyester
Isolation 25mm lana di vetro 18kg/m3
λ (W/mK) 0,039
External sheath aluminium/polyester
Temp. of use -30°C + 150°C
Air speed max 30 m/s
Max pressure 2000 Pa
Box Box 10 m
-
50400037RECTANGULAR CAP
TYPEHeight Width
mm mm
50400037 - 110 55 110
50400037 - 220 55 220
50400036RECTANGULAR GRID
Duct Grid
TYPEHeight Width A B
mm mm mm mm
50400036 - 110 55 110 88 137
50400036 - 220 55 220 80 245
50400035FLAT CHANNEL CLIP
50400034
TYPEHeight Width
mm mm
50400034 - 110 55 110
50400034 - 220 55 220
WALL PLATE
TYPEHeight Width
mm mm
50400035 - 110 55 110
50400035 - 220 55 220
20
-
50400064ISOLATED HORIZONTAL MALE CONNECTION RECT./RECT.TO BE COMPULSORILY INSTALLED ON THE SUPPLY AIR
TYPEA B C Pressure drop (Pa)
mm mm mm 54 m3/h 108 m3/h 216 m3/h
50400064 110 55 110 109 0,2 0,5 1,0
50400064 220 55 220 120 0,1 0,2 0,5
21
50400065ISOLATED HORIZONTAL MALE CONNECTION RECT./CIRC.
TYPEA B C D Pressure drop (Pa)
mm mm mm mm 54 m3/h 108 m3/h 216 m3/h
50400065 110 100 110 55 210 2,3 4,5 9,1
50400065 220 125 220 55 328 0,3 0,7 1,4
TO BE COMPULSORILY INSTALLED ON THE SUPPLY AIR
-
22
50400063ISOLATED SILENCED DUCT WITH MALE CONNECTIONTO BE COMPULSORILY INSTALLED ON THE SUPPLY AIR
Sound absorption level
63 HZ 125 HZ 250 HZ 500 HZ 1 kHz 2 kHz 4 kHz 8 kHz
-1 -3 5 6 12 18 12 9
TYPEA B C
mm mm mm
50400063 220 55 220 1000
50400066ISOLATED MALE ELBOW BEND WITH ROTATING OFFSET SPIGOT RECT./CIRC.
TO BE COMPULSORILY INSTALLED ON THE SUPPLY AIR
TYPEA B C D Pressure drop (Pa)
mm mm mm mm 54 m3/h 108 m3/h 216 m3/h
50400066 110 100 110 55 165 7,4 14,7 29,5
50400066 220 125 220 55 195 3,6 7,3 14,5
-
23
50400062ISOLATED RECTANGULAR DUCT IN PVC
TO BE COMPULSORILY INSTALLED ON THE SUPPLY AIR
50400067ISOLATED VERTICAL BEND 90°TO BE COMPULSORILY INSTALLED ON THE SUPPLY AIR
TYPEA B C Pressure drop (Pa)
mm mm mm 54 m3/h 108 m3/h 216 m3/h
50400062 110 55 110 1500 1,5 3,1 6,1
50400062 220 55 220 1500 0,7 1,3 2,7
TYPEA B C Pressure drop (Pa)
mm mm mm 54 m3/h 108 m3/h 216 m3/h
50400067 110 55 110 120 6,1 12,2 24,3
50400067 220 55 220 165 2,5 5,0 9,9
-
NOTE
50400068ISOLATED HORIZONTAL BEND 90°
TO BE COMPULSORILY INSTALLED ON THE SUPPLY AIR
TYPEA B C Pressure drop (Pa)
mm mm mm 54 m3/h 108 m3/h 216 m3/h
50400068 110 55 110 170 8,6 17,2 34,4
50400068 220 55 220 310 4,2 8,4 16,8
50400069ISOLATED PVC PIPE
TO BE COMPULSORILY INSTALLED ON THE SUPPLY AIR
TYPE ø LONG.(mm)
50400069 100 100 1000
50400069 125 125 1000
24
-
Primaria srl - Via Levico, 31 - Mestrino (PD), 35035 Tel. 049 9003137 - fax 049 9002137 - P.I. 03931130284e-mail: [email protected]