And the winner is Visalys Temp - Kettenbach - Iris CT Dental
-
Upload
iris-ct-dental -
Category
Documents
-
view
223 -
download
1
description
Transcript of And the winner is Visalys Temp - Kettenbach - Iris CT Dental
And the winner is: Visalys® Temp.
1412
22_1
413
The strong temporary crown and bridge material.
For strong crowns and bridges: Visalys® Temp
The high fracture stability of a temporary crown or bridge is an essential criterion for the quality of the material. Before developing Visalys® Temp Kettenbach had already defi ned six parameters crucial for the stability and fracture resistance of a temporary restoration:
• Impact strength• Flexural strength• Diametral tensile strength• E-Modulus• Abrasion• Fatigue limit
As measurements in the laboratory alone are not adequate, dentists were asked by a market research institute to use and then evaluate Visalys® Temp during their daily routine in the practice. The result is impressive: temporary crowns and bridges fabricated using Visalys® Temp fracture noticeably less often than temporary restorations made from other materials.
Stable is good – but not good enough. Visalys® Temp is therefore particularly easy to use and is ideal for temporary restorations, which are intended to meet the highest aesthetic demands. Visalys® Temp is also bisphenol A-free.
Easy application
Smooth surface and high luster without polishing: time-saving – polishing can be omitted or greatly reduced. Minimal smear layer: the temporary restoration is more pleasant to handle after removal from the impression. Can be trimmed precisely: easy fi nishing of the temporary restoration, minimal dust generation. Easy to apply: Visalys® Temp fl ows ideally and is fi rm enough to prevent it running uncontrollably.
Exceptional stability
Considerably fewer repairs: less time-consuming, satisfi ed patients. Also suitable as a long-term temporary restoration (> 4 weeks). Temporary restorations fracture less often during removal and re-fi tting.
High-quality esthetics
Translucency and opalescence similar to that of a natural tooth ensure optimalintegration in the existing dentition due to the chameleon effect.
Natural fl uorescence. Also suitable for particularly high-quality esthetic anterior temporary restorations.
Bisphenol A-free
No health effects on the treating dentist or patient by exposure to Bisphenol A.
The advantages at a glance:
Kettenbach: Trend-setting in Dental and Medical
Being one of the leading suppliers in the market Kettenbach develops, produces and markets medical products of the highest quality in the fi elds of dentistry and medicine. Dentists, doctors and patients have profi ted for over 65 years from innovations made by Kettenbach. Kettenbach is the specialist for dental impressions. Product ranges such as Futar®, Panasil®, Silginat® or Identium® set new standards worldwide with regard to precision and user-friendliness.
Following intensive development, Kettenbach is now extending its range by a new product category. The requirement here is also to provide the highest product quality and maximum customer benefi t. Temporary restorations fabricated using Visalys® Temp are exceptionally stable and fracture resistant due to their monomer structure.Simply intelligent.
free of
Bisphenol A
frei
Visalys® Temp
The result: exceptionally stable
The higher the diametral tensile strength, the lower the risk that, e.g. the margins of the temporary restoration may break off.
Visalys® Temp
Protemp™ 4
Luxatemp® Star
Structur® 3
67
51
51
47
Diametral tensile strength [MPa]
A high E-modulus means that the temporary restoration is resistant to deformation and reliably conserves the intraoral situation until the permanent restoration is fi tted.
Visalys® Temp
Protemp™ 4
Luxatemp® Star
Structur® 3
4152
2716
3937
2148
E-modulus [MPa]
Internal measurements Kettenbach, according to ADA Specifi ca-tion No. 27:76
Internal measurements Kettenbach, test set-up according to DIN EN ISO 10477
High fl exural strength combined with high impact strength reduces the risk of the temporary restoration fracturing in the mouth as a result of high or sudden masticatory loading – e.g. when biting unexpectedly on a cherry stone.
Visalys® Temp
Protemp™ 4
Luxatemp® Star
Structur® 3
12,5
9,5
7,8
8,5
Impact strength [kJ/mm²]
Visalys® Temp
Protemp™ 4
Luxatemp® Star
Structur® 3
132
90
113
85
Flexural strength [MPa]
Measurement at the University of Erlangen, Germany, according to DIN EN ISO 179, DIN 53453
Internal measurements Kettenbach, according to DIN EN ISO 10477 (Feed rate: 1 mm/min)
73
49
51
45
The lower the abrasion, the less wear on the temporary restoration under masticatory loading over time.
Visalys® Temp
Protemp™ 4
Luxatemp® Star
Structur® 3
52
77
63
—
Abrasion [μm]
Measurement at the University of Erlangen, Germany, according to ISO/TS 14569-2
The higher the fatigue limit, the more the material remains fracture resistant, even with ageing, and the more suitable it is for long-term temporary restorations.
Visalys® Temp
Protemp™ 4
Luxatemp® Star
Structur® 3
Fatigue limit [MPa]
Measurement at the University of Erlangen, Germany
not measured
free of
Bisphenol A
frei
The tooth: fully protected
Visalys® Temp was put to the test in a clinically oriented test.
Test conditions: Visalys® Temp and the impression were stored at room temperature (20 °C). Visalys® Temp was applied at 36°C with an impression to a prepared human molar (stored at 36°C) with a retrograde excavated pulp chamber and fi tted temperature sensor.
The temperature in the pulp chamber dropped initially when the Visalys® Temp, stored at room temperature, and impression material were applied. The temperature then increased slightly during setting of the Visalys® Temp, but it did not reach the initial temperature of 36°C, even after three minutes.Conclusion: The heat created during the setting of Visalys® Temp does not pose a threat to the pulp.
Visalys® Temp protects the pulp – Smooth surfaces virtually prevent biofi lm/plaque build-up.
Temperature in the pulp chamber [°C]
0 20 40 60 80 100 120 140 160 180
36,5
36
35,5
35
34,5
34
33,5
33
32,5
32
31,5
Time [sec]
Temperature [°C]
Microscope image – the difference is in the detail.
3D-image from the University of Erlangen of the non-polished Visalys® Temp surface in an optical profi lometer.The uniform, level structure produces a high luster without polishing and hinders the accumulation of plaque.
0.700 μm
0.000 μm (ideal)
-1.800 μm
The opinions: convincingIn a market study* 30 dentists, who currently use either Protemp™ 4 (3M Espe) or Luxatemp® (DMG), were asked by a market research institute to test Visalys® Temp in vivo and the two materials were then evaluated in comparison with each other.
The results:
How do you evaluate the thickness of the smear layer after removal from the impression?
Visalys® Temp Very good/good: 87%Protemp™ 4/Luxatemp® Very good/good: 56%
How do you evaluate the luster of the temporary restoration without polishing?
Visalys® Temp Very good/good: 84%Protemp™ 4/Luxatemp® Very good/good: 61%
How do you evaluate the trimability of the temporary restoration?
Visalys® Temp Very good/good: 92%Protemp™ 4/Luxatemp® Very good/good: 69%
How do you evaluate dust generation when trimming?
Visalys® Temp Very good/good: 62%Protemp™ 4/Luxatemp® Very good/good: 43%
How do you evaluate the fracture resistance/stability of the temporary restoration in situ?
Visalys® Temp Very good/good: 96%Protemp™ 4/Luxatemp® Very good/good: 72%
How do you evaluate the shade stability of the temporary restoration in situ?
Visalys® Temp Very good/good: 91%Protemp™ 4/Luxatemp® Very good/good: 72%
Would you change to Visalys® Temp in future?
Yes 90% No 10%
How do you evaluate the possibility of fi tting the temporary restoration a second time?
Visalys® Temp Very good/good: 96%Protemp™ 4/Luxatemp® Very good/good: 74%
*iConsult, Munich, Germany, 2012, data available at Kettenbach
All in all: Simply intelligent
13780 Visalys® Temp - shade A1
1 x 50 ml cartridge, 15 mixing tips13781 Visalys® Temp - shade A2
13782 Visalys® Temp - shade A3
13785 Visalys® Temp - Intro pack, shade A3 Applyfi x® 6 dispensing gun,1 x 50 ml cartridge, 15 mixing tips
13789 Visalys® Temp - 50 mixing tips
17208 Applyfi x® 6 dispensing gun
The range
Match Visalys® Temp ideally: Silginat® and Multi-Trays
Silginat® and, depending on the indication, partial Multi-Trays are ideal for taking the impression before preparation. Impressions taken using Silginat® are dimensionally stable and can be stored for several weeks. Their crisp detail and easy handling are impressive features.
Kettenbach GmbH & Co. KGIm Heerfeld 735713 Eschenburg ∙ GermanyTelefon: +49 (0) 2774 [email protected]
1412
22_1
413