Ana White - Patrick039s Jelly Cupbard - 2011-12-12

7/27/2019 Ana White - Patrick039s Jelly Cupbard - 2011-12-12

http://slidepdf.com/reader/full/ana-white-patrick039s-jelly-cupbard-2011-12-12 1/16

Patrick's Jelly CupbardPublished on Ana White (http://ana-white.com)

Patrick's Jelly Cupbard

posted by patrickhosey [1]

This DIY Jelly Cupboard Plan features a shelves behind doors and primitive styling. Free simple stepby step plans to build your own.

of 16

http://ana-white.com/users/patrickhosey

http://ana-white.com/users/patrickhosey




About ProjectAuthor Notes:

Well, we've got ourselves a full day of snow shoveling today. I'm sad to say though temperatures

have warmed considerably, we have not yet been able to work on the Momplex. Hopefully today we

of 16




will have an opportunity.

But today, I'm so excited to share with you Patrick's Jelly Cupboard. Patrick and I worked on the plans

together, but making it amazing is all on Patrick!

Primitive furniture is a favorite of mine, and Patrick's Jelly Cupboard with it's distressed finish is

gorgeous!

of 16




Loving the hardware and wire mesh for the doors. Really gives the project characters and

uniqueness.

And some tips from Patrick:

of 16




On your worktable, clamp two boards together at a right angle with a square

of 16




And then use these boards as guides to make perfect square doors.

of 16




Place shims between the doors for a perfect fit as you install hinges.

of 16




And this is one of my favorite tips - for a distressed finish with rubbed dark edges, spray paint with

cheap black spray paint the edges you plan to distress. Paint over, and then sand back to reveal the

black.

of 16




DimensionsDimensions:

Dimensions: Dimensions are shown above.

Materials and ToolsShopping List:

1 – 1x10 @ 8 feet long


1 sheet 1/4” plywood or beadboard paneling



Hinges

KnobsMagnetic Clasps

Cut ListCut List:

2 – 1x12 @ 47 1/4”

3 – 1x10 @ 32”

1 – 1x12 @ 32”

1 – 1x12 @ 35”

1 – 1x3 @ 33 1/2”

2 – 1x3 @ 44 3/4”

1 – 1x2 @ 35”

1 – 1/4” plywood @ 48” x 33 1/2”

2 – 1/4” plywood @ 12” x 38 1/2”4 – 1x3 @ 11”

4 – 1x3 @ 36 1/2”

General Instructions

Please read through the entire plan and all comments before beginning this project. It is also

advisable to review the Getting Started Section. Take all necessary precautions to build safely and

smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards.

Check for square after each step. Always predrill holes before attaching with screws. Use glue with

finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will

not take stain. Be safe, have fun, and ask for help if you need it. Good luck!

of 16




Step 1

Build exterior frame of cupboard with screws and glue. Mark overhangs on top and bottoms and

attach carefully. Adjust for square.

of 16




Step 2

Shelves are 1x10, narrower width than the outside frame. Shelves are installed flush to back of

cabinet. This will give room for your doors to have backing, if used.

of 16




Step 3

Attach plywood to back with 1 1/4" finish nails and glue. Make sure the cabinet is square, and attach

to all fixed boards for best support.

of 16




Step 4

If you are using a pocket hole jig, build the frame first, then attach to the face of the cabinet. You

can also taper bottom legs for a decorative look with a jigsaw or circular saw.

of 16




Step 5

Front is nailed and glued in place. Nail in both front and top directions to secure.

of 16




Step 6

Measure your door openings, as board widths may vary, and build your doors giving an 1/8" gap on

all sides of the doors. Attach backing to doors, and attach with hinges to cupboard.

of 16




Step 7

Finishing InstructionsPreparation Instructions: Fill all holes with wood filler and let dry. Apply

additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the

direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding

residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It

is always recommended to apply a test coat on a hidden area or scrap piece to ensure color

evenness and adhesion. Use primer or wood conditioner as needed.

Armoire [2], Bookshelves [3], Cabinets [4], dining room [5], storage and

organization [6], Intermediate [7], Pioneer [8]

Source URL: http://ana-white.com/2011/12/plans/patrick039s-jelly-cupbard

Links:

[1] http://ana-white.com/users/patrickhosey

[2] http://ana-white.com/category/plans/project-type/armoire

[3] http://ana-white.com/category/plans/project-type/bookshelves

[4] http://ana-white.com/category/plans/project-type/cabinets

[5] http://ana-white.com/category/plans/room/dining-room

[6] http://ana-white.com/category/plans/room/storage-and-organization

[7] http://ana-white.com/category/plans/skill-level/intermediate

[8] http://ana-white.com/category/plans/style/pioneer

http://ana-white.com/category/plans/project-type/armoire

http://ana-white.com/category/plans/project-type/bookshelves

http://ana-white.com/category/plans/project-type/cabinets

http://ana-white.com/category/plans/room/dining-room

http://ana-white.com/category/plans/room/storage-and-organization


http://ana-white.com/category/plans/skill-level/intermediate

http://ana-white.com/category/plans/style/pioneer

http://ana-white.com/2011/12/plans/patrick039s-jelly-cupbard

http://ana-white.com/2011/12/plans/patrick039s-jelly-cupbard

http://ana-white.com/category/plans/style/pioneer

http://ana-white.com/category/plans/skill-level/intermediate



http://ana-white.com/category/plans/room/dining-room

http://ana-white.com/category/plans/project-type/cabinets

http://ana-white.com/category/plans/project-type/bookshelves

http://ana-white.com/category/plans/project-type/armoire

Ana White - Patrick039s Jelly Cupbard - 2011-12-12

Documents

Transcript of Ana White - Patrick039s Jelly Cupbard - 2011-12-12