An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches –...
Transcript of An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches –...
![Page 1: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/1.jpg)
An Experimental Investigation of Hot Switching Contact Damage in RF MEMS Switches
PhD dissertation by Anirban Basu
Dissertation Committee Advisor: Dr Nick McGruer
Co-advisor: Dr George Adams Member: Dr Matteo Rinaldi Member: Dr Carol Livermore
![Page 2: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/2.jpg)
Outline
RF MEMS switches – An overview Experimental setup for contact testing Hot switching in MEMS switches – Results and
Discussions Summary of mechanisms Conclusion and future work
![Page 3: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/3.jpg)
RF MEMS switches
Several companies and universities (NEU, UCSD, RFMD, Omron, Agilent, etc) have developed packaged RF MEMS switches over the last decade.
![Page 4: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/4.jpg)
Applications
Automated Test Equipment
Base-station antennas
Sattelite Communication
Phased Arrays for radar
Reconfigurable radio
RF MEMS SWITCHES
![Page 5: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/5.jpg)
Comparison with other technologies
Device Figure of Merit Switching speed Power dissipated
PIN Diode 800-1600 GHz < 1 µs High
GaAs FET 700 GHz < 1 µs Low
RF MEMS 10-20 THz 5 - 50 µs Low
𝐹𝐹𝐹 =1
2𝜋𝑅𝑜𝑜𝐶𝑜𝑜𝑜
PIN Diode GaAs FET
![Page 6: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/6.jpg)
Concerns
• Reliability – Contact damage (Resistive switches) – Charging (Capacitive switches)
• High Voltage required for actuation (30V-100V)
• Hermetic packaging required • Cost is high as of now
![Page 7: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/7.jpg)
Classification
RF MEMS switches
Signal transmission Circuit configuration Actuation mechanism
Capacitive Resistive
Shunt Series
Electrostatic
Electromagnetic
Piezoelectric
Thermal
![Page 8: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/8.jpg)
The Customized AFM-Setup
N2 Flow
Photodetector
Laser Source
Force sensor
Pillar
• Photodetector generates A-B voltage which is acquired by LabVIEW DAQ
• The A-B voltage can be calibrated and mapped to the force exerted on the Force sensor
![Page 9: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/9.jpg)
Measurement Structures Pillar
• Fabricating actual switches for testing contact behavior alone would not be cost-effective
• The flexibility of testing many different contact materials would be lost if a new batch of switches were to be fabricated each time a different material had to be tested.
• Chips with 3 clamped-clamped beam structures with contact bump in the middle used for testing.
![Page 10: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/10.jpg)
Four-Wire Measurement
Switch
Vs
R= 50Ω
V DAQ
V DAQ
𝑅𝑐𝑜𝑜𝑐𝑐𝑐𝑐 =𝑉𝑐𝑜𝑜𝑐𝑐𝑐𝑐𝑉𝑅
× 𝑅
![Page 11: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/11.jpg)
The Overall Setup
DAQ Connection
BREAKOUT BOX
AFM System
Connection 5 Ω
50 Ω
OPA 548
1 µF
Piezo-Actuator
DAQ
PA85
![Page 12: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/12.jpg)
Hot Switching Requirements
• Hot switching is the application of an RF signal or DC voltage across the contacts of a switch while it is still transitioning from open to closed position or closed to open.
Lifetime Switching cycles
Switching speed Hot switching requirement
T/R switch 8.6 Billion 5 µs 0 dBm
Antenna tuner 440 Million 5 µs +28 dBm (worst case)
PA Tuner 440 Million 5 µs Tuned during transmission nulls
Ref: RF MEMS Switch Technology for Radio Front End Applications, Julio Costa, RFMD
![Page 13: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/13.jpg)
Why study Electrical contacts and hot switching?
• Reliability of a MEMS switch is dependent on the reliability of its contacts.
• Hot switching, being one of the most important reliability issues, needs to be understood and characterized.
• Understanding hot switching mechanisms can enable us to determine a better contact material in the future.
• Knowledge of hot switching specification can enable better circuit and system design
![Page 14: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/14.jpg)
Hot switching – A complex phenomenon
Duration – 106 cycles, Cycling Rate – 500 Hz, Approach/Separation rate – 4400 µm/s, External resistance – 50 Ω
![Page 15: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/15.jpg)
Hot switching – A complex phenomenon
Duration – 106 cycles, Cycling Rate – 500 Hz, Approach/Separation rate – 4400 µm/s, External resistance – 50 Ω
![Page 16: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/16.jpg)
Hot switching vs Cold switching
Cold switched, 77.5 mA Cold switched, 77.5 mA Hot switched, 3.5 V, 77.5 mA
Hot switched, 3.5 V, 77.5 mA
Hot switched, 3.5 V, 77.5 mA
Hot switched, 3.5 V, 77.5 mA
Cold switched, 77.5 mA Cold switched, 77.5 mA
Anode
Cathode Anode
Cathode Anode
Cathode Anode
Cathode
Duration – 106 cycles, Cycling Rate – 500 Hz, Approach/Separation rate – 4400 µm/s, External resistance – 50 Ω
![Page 17: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/17.jpg)
Hot switching vs Cold switching
![Page 18: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/18.jpg)
Leading Edge vs Trailing Edge (Anode)
Leading Edge HS Leading Edge HS Leading Edge HS
Trailing Edge HS Trailing Edge HS Trailing Edge HS
(a) 104 Cycles
(b) 104 Cycles
(c) 105 Cycles
(d) 105 Cycles
(e) 106 Cycles
(f) 106 Cycles
5 μm
5 μm
5 μm
5 μm
5 μm
5 μm
Cycling Rate – 500 Hz, Approach/Separation rate – 4400 µm/s, External resistance – 50 Ω, Polarity – Anode
![Page 19: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/19.jpg)
Leading Edge vs Trailing Edge (Cathode)
Cycling Rate – 500 Hz, Approach/Separation rate – 4400 µm/s, External resistance – 50 Ω, Polarity – Cathode
Leading Edge HS Leading Edge HS Leading Edge HS
Trailing Edge HS Trailing Edge HS Trailing Edge HS
(a) 104 Cycles
(b) 104 Cycles
(c) 105 Cycles
(d) 105 Cycles
(e) 106 Cycles
(f) 106 Cycles
5 μm
5 μm
5 μm
5 μm
5 μm
5 μm
![Page 20: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/20.jpg)
Quantitative analysis of material transfer in Leading edge vs Trailing edge
20
Quantitative Comparison of Leading Edge and Trailing Edge Hot Switching
• Log-log plot for material transfer to / from the contact bump vs no of cycles for both polarities
• The data points correspond to average of at least three tests for same conditions
• Volumetric analysis done using AFM scans
(Volume measurements – Courtesy Ryan Hennessy)
![Page 21: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/21.jpg)
Leading Edge vs Trailing Edge – Difference
Duration – 106 cycles, Cycling Rate – 500 Hz, Approach/Separation rate – 4400 µm/s,
![Page 22: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/22.jpg)
Pre-contact current
Ref: M. Vincent, S. W. Rowe, C. Poulain, D. Mariolle, L. Chiesi (2010), “Field emission and material transfer in microswitches electrical contacts”, Applied Physics Letter vol 97
Current transients observed by this group at an approach rate of 8.8 µm/s and hot switching voltage of 5 V
![Page 23: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/23.jpg)
Analysis of Pre-Contact Current
Sustained “emission” current
Contacts undamaged from the sustained pre-contact current
![Page 24: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/24.jpg)
Study of Field Emission
Direct tunneling from cathode to anode Fowler-Nordheim tunneling from cathode to vacuum
![Page 25: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/25.jpg)
Material transfer from Field emission
If current = 1 µA current, time of current flow = 50 ns, no of electrons required = 3.125 x 105. If each electron has 3.5 eV of energy, the total available energy = 1.75 x 10-13 J of energy.
Specific heat 0.024 kJ/mole-K
Melting temperature 2607 K
Specific heat of fusion 23.7 kJ/mole
Boiling temperature 4423 K
Specific heat of evaporation 567 kJ/mole
5.72 x 10-14 J of energy is needed to evaporate 500 nm3 of Ru
![Page 26: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/26.jpg)
Material transfer from Field evaporation
Field evaporation between contacts with small separation: Positive Ru ions are pulled from anode on to the cathode leading to material transfer
• At greater than 6 Å, electric field required for evaporation = 4.1 V/Å • At 4 – 6 Å, required field drops by 30 % • At less than 4 Å, electric field drops by 50% • At 3.5 V, separation required for field evaporation = 1.5 Å
Ref: Tsong, T. T. (1991), “Effects of an electric field in atomic manipulations”, Phys. Rev. B vol 44 pp 13703 – 13710
![Page 27: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/27.jpg)
Heating and ionization
𝑉2 = 8 � 𝜆𝜆𝜆𝜆𝑇𝑚
𝑇0
𝜆𝜆 = 𝐿𝜆
𝜆𝑚2 = 𝜆02 +𝑉2
4𝐿
𝑁𝑖+1
𝑁𝑖 =𝑍𝑖+1
𝑍𝑖2
𝑛𝑒ℎ3(2𝜋𝑚𝑒𝑘𝜆)3 2� 𝑒
𝜒𝑖𝑘𝑇
Melting voltage of Ru = 0.8 V for Ru Boiling voltage = approx 1.5 V
Relationship between contact voltage and temperature:
Wiedemann-Franz’s law states
This gives us:
A high contact voltage can lead to contact material melting and boiling. If the temperature of the metal vapor is high enough, we can get ionization leading to ions being pulled towards cathode
Asperities coming into contact / Metal bridge forming
Anode
Cathode
Metal vapor is ionized at a high temperature
Anode
Cathode
Saha equation:
Ionization temperature approx 5000 K!
![Page 28: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/28.jpg)
Electromigration
Ref: R. S. Timsit (2010), “Electromigration in a Liquid Bridge Before Contact Break,” Proceedings of the 56th IEEE Holm Conference on Electrical Contacts, 2010
𝑉 = 𝐽𝑒𝑍∗𝜆𝜌/𝐾𝜆
• Electromigration usually occurs from cathode to anode
• In a fluid, however, since the ions have additional thermal energy, they may be prone to move towards the cathode.
• Anode to cathode material transfer has been reported in Al, Ag, In and other metals, particularly in the molten state
Electromigration is given by:
![Page 29: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/29.jpg)
Electromigration leading to thermal diffusion
• Electric field between the contacts can cause surface diffusion of the ions towards the apex of the anode.
• If tunneling current causes heating at the anode, this can lead to melting which can further promote surface diffusion towards the apex of the contact.
• The process of surface diffusion is similar to electromigration where ions are pulled by the electric field between the contacts.
• Ultimately a liquid cone may form at this tip which can be long enough to touch the other electrode thereby depositing material on to it.
• This was speculated to be a material transfer mechanism in AFM/STM tips
Ref: Tsong, T. T. (1991), “Effects of an electric field in atomic manipulations”, Phys. Rev. B vol 44 pp 13703 – 13710
![Page 30: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/30.jpg)
Material transfer due to thermal gradient
Metal Bridge
Anode
Cathode
At the trailing edge, if a metal bridge is formed, the hottest point on the metal bridge can determine the point where the bridge ruptures (if rupture is caused by a portion of the bridge evaporating)
• Thomson effect will shift the hottest point towards the anode.
• The pillar, being a better heat sink will cause the hottest point to shift towards the contact bump (irrespective of polarity.
Metal Bridge ruptures
Anode
Cathode
Thomson Effect
![Page 31: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/31.jpg)
Evidence of material transfer due to thermal effect
Duration – 40 to 50 cycles, Separation rate – 8.8 nm/s, External resistance – 50 Ω
![Page 32: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/32.jpg)
Material transfer without contacts separating
Applied voltage = 5V, Duration – 40 to 50 cycles, Separation rate – 8.8 nm/s, External resistance – 50 Ω Current never went below 75 – 80 mA Contact voltage at 80 mA = 1 V implying melting
![Page 33: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/33.jpg)
Bipolar Hot Switching Damage
Leading Edge HS Trailing Edge HS
Trailing Edge HS
40x106 Cycles 40x106 Cycles
120x106 Cycles
5 μm 5 μm
5 μm
5 μm
Applied voltage – 3.5 V, Approach/Separation rate – 4400 µm/s, External resistance – 50 Ω
![Page 34: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/34.jpg)
Leading edge current characteristics due to system capacitance
R3
R4
50
0
V13.5
+-
+- S1VON = 2VOFF = 0V
V2
TD = 0TF = 10usPW = 50usPER = 100us
V1 = 0 TR = 10usV2 = 2
0
5 C3
4f FC41u
L1
125nH C6
35pF
• The 35 pF capacitance arises due to the isolation oxide layer between device and handle sides of the chip
• In a real switch, inherent capacitance maybe present in the system when the switch is part of a transmission line
• Contact resistance drops from infinity to 1 ohm in 10 us
![Page 35: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/35.jpg)
Current vs time for different external resistances – SPICE results
50 Ω
20k Ω 1Meg Ω
500 Ω 5k Ω
10Meg Ω
![Page 36: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/36.jpg)
Contact damage corresponding to different external resistances
Applied voltage – 3.5 V, Duration – 106 cycles, Separation rate – 4400 µm/s, External resistance – 50 Ω
![Page 37: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/37.jpg)
Leading vs Trailing edge difference at 5 kΩ – what causes it?
Duration – 106 cycles, Cycling Rate – 500 Hz, Approach/Separation rate – 4400 µm/s,
• At melting voltage, contact resistance R = 1 kΩ
• Contact resistance R = 𝜌2𝑐
• ρ = 7.1 µΩ-cm, implying a = 0.36 Å • Radius size less than an atom! • Voltage between contacts also
takes more time to build up.
![Page 38: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/38.jpg)
• Up to 5k Ω, the capacitance in the system has no effect on the maximum current through the contact at the instance of closing
• From 5k to 1Meg, the capacitance determines the maximum current in the circuit at the instance of closing.
• Since maximum current in the circuit with a 1Meg resistance is 150 µA, the current associated with leading edge hot switching damage cannot exceed this value
Analysis of the current for different external resistors
![Page 39: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/39.jpg)
a) Mechanical transfer through adhesion, cold welding or softening of contact as observed in low voltage hot switching
b) Field Evaporation c) Field emission leading to heating, melting and
evaporation d) Electromigration with and without melting which can
also manifest itself through surface diffusion e) Ionization of metal vapor f) Formation of metal bridge where Thomson effect and
thermal asymmetry can cause the hottest point of the bridge to be biased towards one of the electrodes
Summary of mechanisms
![Page 40: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/40.jpg)
• The results of hot switching tests at different voltages demonstrate the presence of multiple contact damage mechanisms.
• The mechanisms operate at very short separations or when the contacts are just touching.
• While there are probably some similarities between leading and trailing edge hot switching (similar amount of material transfer at a switching speed of 4400 µm/s), there could be effects which are present in one and not the other.
• It is also noted that pre-contact current, observed in ‘dirty’ contacts do not cause material transfer.
Conclusions
![Page 41: An Experimental Investigation of Hot Switching Contact ......Hot switching in MEMS switches – Results and Discussions Summary of mechanisms Conclusion and future work . RF MEMS switches](https://reader033.fdocuments.us/reader033/viewer/2022042405/5f1e8e249c513e5f0833161e/html5/thumbnails/41.jpg)
• Contact damage due to AC hot switching – Since contact damage varies with hot switching voltage, AC hot
switching will typically give a combination of the types of damage observed at different voltages
• Investigating hot switching in a real microswitch – Vast difference of thermal properties between the switch cantilever
and the substrate can lead to further contact damage triggered by thermal mechanism
– Relative dominance of thermal mechanism vis-à-vis field effects can be characterized
• Analyzing the correlation between melting/boiling point of a material with corresponding contact damage
Future work