Aluminium motors · ABB Motors This product catalogue contains electrical and mechanical data on...

Aluminium motors

ABB Motors

ABB Motors

This product catalogue contains electrical and mechanical dataon the aluminium motor range available from ABB Motors. It canbe used in conjunction with the catalogue BA/Basic GB whichcontains basic technical information about standard motors.

Aluminium motors

3ABB Motors

Totally enclosed squirrel cagethree phase motorsSizes 63 to 250, 0.18 to 75 kW

Section Page

Mechanical design 4StatorDrain holesTerminal boxConnectionsBearingsTransport lockingAxially-locked bearingBearing lifePulley diameterPermissible loading on shaftLubrication

Electrical design 10Stator winding temperature sensorst6-times

Ordering information 11

Data tables, single-speed motors 12

Data at voltage ranges 20

Data table, two-speed motorsfor fan drives 22

Data tables, two-speed motors withhighest output at both speeds 26

Motors with other no. of poles 29

Rating plates 30

Variant codes 31

Dimension drawings 35

Dimensions for alternative designs 51

Accessories 52

Aluminium motors in brief 54

ABB Motors product range 56

Cutaway view, M2AA 132 59-60

ABB Motors 61

ABB Motors reserves the rightto change the design, technicalspecification and dimensionswithout prior notice.

4 ABB Motors

Mechanical design

Drain holesMotors that will be operated in very humid or wetenvironments, and especially under intermittent duty,should be provided with drain holes. The appropriate IMdesignation, such as IM 3031, is specified on the basisof the method of mounting the motor.

In the basic design, sizes 63 to 100 are supplied withoutdrain holes, with which they can be provided as needed.If holes are drilled, the degree of protection will changeto IP 54. If the motors are provided with special feltplugs in the holes, the IP 55 will be retained.

Sizes 112 to 250 are provided with closable plasticplugs in the drain holes (see diagram below). The plugswill be open on delivery. When mounting the motors, itshould be ensured that the drain holes face downwards.In the case of vertical mounting, the upper plug must behammered home completely. In very dustyenvironments, both plugs should be hammered home.

See variant codes 065, 066 and 076 under the heading,“Drain holes”, on page 31.

Terminal bo xSizes 63 to 180The terminal box is made of light metal alloy and islocated on top of the stator. The lower part of the box isintegrated with the stator. It is provided with 2 knockoutopenings on each side. Sizes 160-180 also have asmaller opening. Cable glands are not included.

Sizes 200 to 250The terminal box and cover are made of deep drawnsteel and mounted on top of the stator. The box isbolted to the stator and is thus not rotatable. The size ofthe box is the same in all motors.

In the basic design, the terminal box is provided withtwo FL 13 flange openings, one on each side. Theopening on the right side, seen from the D-end, issupplied with a flange with two holes for Pr 37 cableglands. On delivery, the holes are sealed by means ofplastic plugs. Cable glands are not supplied. The

opening on the other side is provided with a coverflange. The box can also be provided with an FL 13opening towards the N-end.

The motors can also be provided with an extra largeterminal box, standard for voltage code S. See variantcode 019, under the heading “Terminal box”, on page34. This will increase the dimension HD by 32 mm. Thebox is supplied with two FL 21 openings. The rightopening is provided with a flange with two holes for Pr54 cable glands. The holes are sealed by means ofplastic plugs. Cable glands are not supplied. Theopening on the other side is provided with a coverflange.

When new motors are manufactured, the terminal boxcan be mounted on the left or the right side. See variantcode 021 and 180, under the heading “Terminal box”,on page 34.

Stator framework, bearing shields and feet are made ofan extra corrosion resistant aluminium alloy with lowcopper content, with the following exceptions:Size 250-2 SMA, basic version, has cast iron feet.

StatorSize 250-2 SMB, high output version, has cast iron feetand bearing shields.

The flange bearing shields of sizes 180 to 250 aremade of cast iron.

5ABB Motors

Basic ver sion with deep gr oove ballbearingsBasic design motors

Single-speed motors Two-speed motors

Motor Foot- and flange-mounted motor Foot- and flange-mounted motorsize D-end N-end D-end N-end

63 6202-2Z/C3 6202-2Z/C3 6202-2Z/C3 6202-2Z/C371 6203-2Z/C3 6202-2Z/C3 6203-2Z/C3 6202-2Z/C380 6204-2Z/C3 6203-2Z/C3 6204-2Z/C3 6203-2Z/C3

90 6305-2Z/C3 6204-2Z/C3 6305-2Z/C3 6204-2Z/C3100 6306-2Z/C3 6205-2Z/C3 6306-2Z/C3 6205-2Z/C3112 6206-2Z/C3 6205-2Z/C3 6206-2Z/C3 6206-2Z/C3

132 S 6208-2Z/C3 6206-2Z/C3 6208-2Z/C3 6206-2Z/C3132 M 6208-2Z/C3 6206-2Z/C3 6208-2Z/C3 6208-2Z/C3160 6209-2Z/C3 6209-2Z/C3 6209-2Z/C3 6209-2Z/C3180 6210-2Z/C3 6209-2Z/C3 6210-2Z/C3 6209-2Z/C3

200 6312/C3 6210/C3 6312/C3 6210/C3225 6313/C3 6212/C3 6313/C3 6212/C3250 6315/C3 6213/C3 6315/C3 6213/C3

Comparison of Pr and PgPr 15.4 Pg 9 Pr 37 Pg 29Pr 18.6 Pg 11 Pr 47 Pg 36Pr 22.5 Pg 16 Pr 54 Pg 42Pr 28.3 Pg 21

ConnectionsThe terminal block is provided with 6 terminals forconnecting Cu-cable. The terminals are marked inaccordance with IEC 34-8.

Terminal bo xMotor Method of Maximum connectablesize connection For screw Cu-cable area, mm2

63-100 Screw terminal 2.5112, 132 Cable lug M 5 10160, 180 Cable lug M 6 35200-250 Cable lug M 10 70

such cases, the axial force must only operate in onedirection.

Motor versions with roller bearings tolerate greaterradial forces.

BearingsThe motors are provided with bearings, according to thetables below.

Greater axial forces can be tolerated if the motors areprovided with angular contact ball bearings. Note that in

High-output motors

Single-speed motors

Motor Foot- and flange-mounted motorsize D-end N-end

71 6203-2Z/C3 6202-2Z/C380 6204-2Z/C3 6203-2Z/C390 6305-2Z/C3 6204-2Z/C3

100 6306-2Z/C3 6205-2Z/C3112 6206-2Z/C3 6206-2Z/C3132 6208-2Z/C3 6208-2Z/C3160 6209-2Z/C3 6209-2Z/C3180 6210-2Z/C3 6209-2Z/C3

200 6312/C3 6210/C3225 6313/C3 6212/C3250 6315/C3 6213/C3

1) Knockout openings.

Connection openingsMotorsize Opening Holes

63 1) 4 x Pr 18.671-100 1) 4 x Pr 22.5

112, 132 1) 2 x (Pr 28.3 + Pr 22.5)160, 180 1) 4 x Pr 37 + 2 x 15.4200-250 2 x FL 13 2 x Pr 37

Alternative design63-series bearings at the D-endStandard for sizes 90, 100, and 200 to 250.See variant code 188, under the heading “Bearings andlubrication”, on page 31.

Version with roller bearings.It is recommended to use roller bearings in belt drivesfor motor sizes 160 - 250.

6 ABB Motors

Basic design motors


Motor Foot- and flange-mounted motor Foot- and flange-mounted motorsize D-end N-end D-end N-end

160 NU 209 ECP - NU 209 ECP -180 NU 210 ECP - NU 210 ECP -

200 NU 312 ECP - NU 312 ECP -225 NU 313 ECP - NU 313 ECP -250 NU 315 ECP - NU 315 ECP -

Version with roller bearingsSee variant code 037, under the heading “Bearings andlubrication”, on page 31.

High-output motors

Single-speed motors

Motor Foot- and flange-mounted motorsize D-end N-end

160 NU 209 ECP -180 NU 210 ECP -

200 NU 312 ECP -225 NU 313 ECP -250 NU 315 ECP -

Basic design motors


Foot- and flange-mounted motor Foot- and flange-mounted motorMotor D-end N-end D-end N-endsize 058 059 058 059

112 7206 BE 7205 BE 7206 BE 7206 BE132 7208 BE 7206 BE 7208 BE 7208 BE

160 7209 BE 7209 BE 7209 BE 7209 BE180 7210 BE 7210 BE 7210 BE 7210 BE

220 - 7210 BE - 7210 BE225 - 7212 BE - 7212 BE250 - 7213 BE - 7213 BE

Transpor t loc kingMotors provided with roller bearings or angular contactball bearings are fitted with a transport lock to prevent

Axiall y-loc ked bearingsThe table below shows which of the motor’s bearings isaxially locked in the bearing seat, by an inner bearingcover.

See also variant code 042, under the heading “Bearingsand lubrication”, on page 31.

damage to the bearings, due to vibration, duringtransport.

High-output motors

Single-speed motors

Foot- and flange-mounted motorMotor D-end N-endsize 058 059

112 7206 BE 7206 BE132 7208 BE 7208 BE

160 7209 BE 7209 BE180 7210 BE 7209 BE

200 - 7210 BE225 - 7212 BE250 - 7213 BE

Motor Foot-mounted Flange-mounted motorssize motors Large flange Small flange

63-80 1) D-end 1)

90, 100 D-end D-end D-end

112, 132 1) D-end D-end160-180 D-end D-end -200-250 N-end N-end -

Version with angular contact ball bearingsSee variant codes 058 and 059, under the heading“Bearings and lubrication”, on page 31.

1) A spring washer at the N-end locks the rotor at the D-end.

7ABB Motors

Bearing lif eThe nominal life is defined as the number of hours thatare attained or exceeded by 90% of identical bearings,in a large test series, under certain specified conditions.50% of the bearings attain a life of as much as 5 timesthis figure.

The life of bearings is dependent on various factors,such as bearing load, motor speed, operating tempera-ture and the purity of the grease. The permissible radialand axial loading for different motor sizes is shown inthe table on page 8 and 9.

The table is valid for 50 Hz. For 60 Hz and/or someother bearing life than is specified in the table, thevalues are changed according to the table on the right.

The table values assume the occurrence of only radial(FR) or axial (FA) forces. In the case of simultaneousradial and axial forces, information can be supplied onrequest. It is assumed that the radial force, FR, isapplied at the end of the motor shaft, according to thediagram on the right.

Permissib le force at c hang ed bearing lif e or suppl y frequenc y

Bearing life in hours atPermissible force, as percentage of

50 Hz 60 Hz value in table on page 8 and 9

25000 21000 100% of valuefor 25000 hours




LLXLLX – X

FRX = FR • —————

where:

LLX = distance between end of motor shaft extensionat D-end and centre of bearing at N-end.

X = distance between end of motor shaft extensionat D-end and centre of pulley.

In the case of forces applied beyond the end of theshaft, information can be supplied on request.

LLX values for basic design of single-speed motors

Motor LLX E Motor LLX Esize mm mm size mm mm

63 164 3071 181 3080 208 40

90 245 50100 282 60

112 M 284 60112 MB 316 60

132 S(A, B) 366 80132 M(A) 366 80132 MB-6 366 80

132 SC 402.5 80132 MB-4, 8 402.5 80132 MC 482.5 80

160 M 2-8 506.3 110160 M 2/4, 4/6, 4/8 506.3 110160 MA 2, 8, 2/4 506.3 110

160 L 2-6 506.3 110160 L 8 547.3 110160 L 2/4 506.3 110

160 L 4/6, 4/8 547.3 110160 LB 2, 4 506.3 110160 LB 6, 8 547.3 110

180 M 2, 4 561.3 110180 M 2/4, 4/6, 4/8 561.3 110180 L 4-8 561.3 110

180 L 2/4, 4/6, 4/8 581.3 110180 LB 2 561.3 110180 LB 4-8 581.3 110

200 623.3 110225-2 686 110

225-4, 6, 8 716 140250-2-8 721.5 140

When the desired bearing life has been determined, theminimum permissible pulley diameter can be calculatedwith FR (or FRX), according to the formula:

D =1.9 • 107 • K • P

n • FR(X)

where:

D = diameter of pulley, mmP = power requirement, kWn = motor speed, r/min.K = belt tension factor, dependent on belt type and

type of duty. A common value for V-belts isK = 2.5

Pulle y diameter

FR = permissible radial force according to the tableon page 8 and 9.

FRX = permissible radial force according to theformula under the heading “Bearing life”,above.

8 ABB Motors

Permissible axial force FA and radial force FRThe table values for FA apply to horizontal mounting. In the case of vertical mounting, consideration must be givento the rotor weight, according to note 2. The bearing life, L10, is calculated according to SKF’s new theory on bearinglife, L10aah

, which also takes the purity of the grease into consideration. An adequate lubrication is a necessaryprerequisite for the table below.

Ball bearings Roller bearings

Basic design with deep Alternative design Alternative designgroove ball bearings with 63-series bearings with roller bearings

25000 hrs 40000 hrs 25000 hrs 40000 hrs 25000 hrs 40000 hrs

Rotor weightMotor No. of FGR FA FR FA FR FA FR FA FR FA FR FA FRsize poles N N N N N N N N N N N N N

631) 2 590 400 520 4004 665 400 580 4008 695 400 600 400

711) 2 735 570 650 5704 820 570 720 5706 885 570 770 5708 880 570 765 570

801) 2 1005 750 885 7504 1120 750 995 7506 1205 750 1050 7508 1240 750 1075 750

901) 3) 2 1835 1200 1625 12004 2055 1200 1805 12006 2210 1200 1930 12008 2285 1200 1985 1200

1001) 3) 2 2370 1800 2100 18004 2645 1800 2330 18006 2830 1800 2480 18008 2925 1800 2555 1800

112 M1) 2 64 1500 1420 1320 1280 2230 1700 1970 17004 84 1600 1410 1390 1250 2410 1700 2110 17006 85 1730 1510 1500 1340 2590 1700 2260 17008 89 1750 1530 1510 1360 2680 1700 2320 1700

112 MB1) 2 85 1530 1470 1340 1330 2250 1700 1990 17004 106 1600 1430 1390 1260 2410 1700 2110 17006 107 1720 1520 1490 1340 2590 1700 2250 17008 107 1760 1560 1520 1370 2680 1700 2320 1700

132 SA1) 2 89 2570 2360 2260 2140 3460 3180 3070 2870132 SB1) 2 101 2570 2360 2260 2130 3460 3170 3070 2870132 SC1) 2 143 2520 2430 2210 2200 3410 3200 3020 2960

132 S1) 4 138 2770 2440 2440 2180 3770 3200 3320 2990132 M1) 4 160 2750 2410 2420 2150 3750 3200 3290 2950132 MB1) 4 211 2680 2440 2340 2170 3670 3200 3220 3000

132 S1) 6 140 2950 2560 2580 2270 4020 3200 3520 3120132 MA1) 6 165 2940 2530 2570 2250 4010 3200 3500 3100132 MB1) 6 197 2910 2500 2550 2220 3980 3200 3480 3070132 MC1) 6 214 2830 2510 2460 2220 3900 3200 3400 3090

132 S1) 8 165 3040 2630 2650 2330 4150 3200 3610 3200132 M1) 8 197 3020 2590 2630 2300 4130 3200 3590 3170132 MB1) 8 214 2940 2630 2560 2330 4050 3200 3520 3200

160 MA1) 2 211 3040 2570 2680 2320 4730 3500 4220 3500 3050 3500 2720 35008 280 3340 2780 3000 2550 5240 3500 4640 3500 3400 3500 3100 3500

160 M1) 2 227 3040 2570 2680 2320 4730 3500 4220 3500 3060 3500 2710 35004 270 3340 2780 2970 2500 5230 3500 4640 3500 3370 3500 3000 35006 320 3330 2770 2960 2490 5220 3500 4630 3500 3330 3500 2970 35008 320 3330 2770 2960 2490 5220 3500 4630 3500 3330 3500 2970 3500

160 L1) 2 277 3340 2790 2980 2510 5240 3500 4650 3500 3350 3500 2980 35004 338 3330 2770 2960 2490 5220 3500 4630 3500 3330 3500 2970 35006 374 3160 2490 2780 2210 5050 3500 4470 3500 3150 3500 2760 35008 445 3220 2580 2910 2250 4720 3500 4740 3500 3590 3500 3170 3500

160 LB1) 2 296 3340 2790 2980 2510 5240 3500 4650 3500 3350 3500 2980 35004 374 3160 2490 2780 2210 5050 3500 4470 3500 3150 3500 2760 35006 445 3220 2580 2910 2250 4720 3500 4740 3500 3590 3500 3170 35008 445 3220 2580 2910 2250 4720 3500 4740 3500 3590 3500 3170 3500

180 M1) 2 332 2820 3710 2420 3270 4660 5550 4250 5110 2820 5900 2420 59004 451 3120 3870 2660 3360 4950 5710 4500 5200 3120 5900 2660 5900

Permissib le loading on shaft

2) Method of mounting Direction of force Permissible axial force

Horizontal Horizontal FA according to tableVertical Downwards FA – rotor weight FGR1)

Vertical Upwards FA + rotor weight FGR1)

1) For motor sizes 63 to 180, axial tension in the direction of the shaft isassumed. The specified values take the weight of the rotor and theeffects of the spring washer at the N-end into consideration.

3) Basic design with 63-series bearings at the D-end.

9ABB Motors

2) Mounting arrangement Direction of force Permissible axial force

Horizontal Horizontal FA according to tableVertical Downwards FA – rotor weight FGR1)

Vertical Upwards FA + rotor weight FGR1)

Permissible axial force FA and radial force FR – contd.

Ball bearings Roller bearings

Basic design with deep Alternative design Alternative designgroove ball bearings with 63-series bearings with roller bearings

25000 hrs 40000 hrs 25000 hrs 40000 hrs25000 hrs 40000 hrs

Rotor weightMotor No. of FGR FA FR FA FR FA FR FA FR FA FR FA FRsize poles N N N N N N N N N N N N N

180 L1) 4 522 3030 3830 2560 3310 4870 5670 4390 5150 3030 5900 2560 59006 571 3360 4220 2870 3660 5200 5900 4710 5500 3360 5900 2870 59008 561 3540 4320 3010 3730 5370 5900 4850 5570 3540 5900 3010 5900

180 LB1) 2 382 2820 3710 2420 3270 4660 5550 4250 5110 2820 5900 2420 59004 602 3030 3830 2560 3310 4870 5670 4390 5150 3030 5900 2560 59006 610 3360 4220 2870 3660 5200 5900 4710 5500 3360 5900 2870 59008 606 3540 4320 3010 3730 5370 5900 4850 5570 3540 5900 3010 5900

200 MLA3) 2 490 1600 4070 1360 3600 1600 7790 1360 77904 638 1750 4410 1480 3860 1750 7790 1480 77906 697 1870 4600 1590 3990 1870 7790 1590 77908 765 1880 4680 1570 4040 1880 7790 1570 7790

200 MLB3) 2 559 1570 4060 1340 3590 1570 7790 1340 77904 746 1670 4360 1400 3810 1670 7790 1400 77906 785 1800 4540 1510 3940 1800 7790 1510 77908 883 1870 4670 1470 4030 1780 7790 1470 7790

200 MLC3) 2 579 1560 4050 1330 3590 1560 7790 1330 77906 873 1670 4430 1380 3820 1670 7790 1380 7790

225 SMA3) 4 746 2490 4930 2130 4320 2490 8300 2130 83008 893 2790 5420 2380 4700 2790 8300 2380 8300

225 SMB3) 2 697 2200 4530 1890 4010 2200 8900 1890 89004 814 2440 4870 2070 4260 2440 8300 2070 83006 691 2570 5080 2170 4400 2570 8300 2170 83008 971 2720 5350 2310 4630 2720 8300 2310 8300

225 SMC3)2 765 2170 4510 1860 3990 2170 8900 1860 89004 942 2360 4840 1980 4230 2360 8300 1980 83006 1090 2465 5020 2065 4340 2460 8300 2060 83008 1110 2580 5230 2160 4500 2580 8300 2160 8300

250 SMA3) 2 824 2620 5620 2250 4980 2620 9100 2250 91004 971 2970 6200 2530 5440 2970 11550 2530 115506 1235 3100 6430 2630 5590 3100 11550 2630 115508 1255 3230 6650 2740 5760 3230 11550 2740 11550

250 SMB3) 2 942 2570 5610 2210 4960 2570 9100 2210 91004 1175 2860 6140 2410 5380 2860 11550 2410 115506 1430 2985 6400 2500 5560 2980 11550 2500 115508 1450 3080 6590 2570 5700 3080 11550 2570 11550

LubricationOn delivery, the motors are lubricated with a type ofgrease intended for use in dry or humid environments,at normal ambient temperatures. Motor sizes 63 to 100are lubricated for bearing temperatures of between -25to +150°C. Motor sizes 112 to 250 are lubricated forbearing temperatures of between -30 to +110°C. Seealso variant codes 039 and 40, under the heading“Bearings and lubrication”, on page 31.

Information about ambient temperature applies tostandard motors according to insulation class F andtemperature rise class B.

Motors without valve lubricationHours of operation during which the bearings still have adequate lubrication, L 01. (Adequate lubrication, however max. 5 years)

Ambient temperature: 25 °C Ambient temperature: 40 °CMotor Motor size Motor sizespeedr/min 63-100 112, 132 160, 180 63-100 112, 132 160, 180

3000 26000 22000 16000 21000 11000 80001500 44000 42000 32000 34000 21000 160001000 44000 44000 42000 40000 23000 21000750 44000 44000 44000 43000 27000 22500

On request, motor sizes 112 to 180 can be providedwith grease nipples for both bearings. See variant code041, under the heading “Bearings and lubrication”, onpage 31.

The basic design of motor sizes 200 to 250 haveprovision for bearing lubrication during service.Lubrication intervals and grease quantities are specifiedon a plate on the motor as well as in the instructions formaintenance supplied with the motor.

The lubrication interval is defined as the period afterwhich 99% of the bearings still have enough lubrication,L

01. At double the time 90% of the motors still have

adequate lubrication. (L10

)

1) For motor sizes 63 to 180, axial tension in the direction of the shaft isassumed. The specified values take the weight of the rotor and theeffects of the spring washer at the N-end into consideration.

3) Basic design with 63-series bearings at the D-end.

10 ABB Motors

Sophisticated winding machinery is used to producethe stators of ABB Motors standard pole products,such as M2AA range, shown.

Electrical design

Stator winding temperaturesensor s

winding. For other sizes see under the heading "Statorwinding temperature sensors" on page 33.

t6-times in seconds

Motor size 2 poles 4 poles 6 poles 8 poles

63-80 The starting current of sizes 63 to 80, 2 to 8 poles,and sizes 90 to 100, 4 to 8 poles, is <6 x the ratedcurrent.

90 9100 10

112 M 15 12 13 11132 S - 12 15 12132 SA 17 - - -132 SB 16 - - -

132 M - 12 - 13132 MA - - 13 -132 MB - - 14 -

160 MA 35 - - 27160 M 27 16 21 17160 L 26 17 17 17160 LB 16 16 15 15

180 M 25 20 - -180 L - 20 23 31180 LB 18 17 19 27

200 MLA 25 29 24 26200 MLB 21 28 23 21200 MLC 16 - 20 -

225 SMA - 23 - 24225 SMB 26 20 20 20225 SMC 20 19 24 24

250 SMA 18 28 27 24250 SMB 20 18 27 24

Motors frame size 200-250 have as standard 3 PTCthermistors for 150 °C connected in series in the stator

t6- times f or setting of motorprotectionSetting of certain electronic motor protection devicesrequires knowledge of the t

6 time.

t6 is defined as the acceptable time, from thermal

considerations, for which a motor can withstand thelocked rotor condition with a supply current equal to 6times the rated value.

Note: the starting current of some smaller motor sizeswith normal supply voltage is less than 6 times the ratedvalue.

11ABB Motors

Sample or der

Ordering inf ormation

When placing an order, the motor type, size and product code must be specified. The productcode of the motor is composed in accordance with the following example.

Motor size

A Motor typeB Motor sizeC Product codeD Code for mounting

arrangementE Voltage and frequency

codeF Generation code

followed by variantcodes

A B C D, E, F

M2AA 112 M 3GAA 112 001 - ADA, 032, 043, etc. 1 2 3 4 6 7 8 9 10 1112 13 14...5

Positions 1 and 23G = Business area ABB Motors

Position 3Enclosure and stator frame materialA = Totally enclosed motor with aluminium stator frame

Position 4Type of rotorA = Squirrel cage rotor

Positions 5 and 6IEC size

06 = 6307 = 7108 = 8009 = 9010 = 100

Position 7Pole pairs1 = 2 poles 5 =10 poles2 = 4 poles 6 =12 poles3 = 6 poles 7 =>12 poles4 = 8 poles 8 =Two-speed motors

9 =Multi-speed motors

Positions 8 to 10Serial number

Position 11- (dash)

Position 12Mounting arrangementA = Foot-mounted motorB = Flange-mounted motor. Large flange with

clearance holes.C = Flange-mounted motor. Small flange with tapped

holes.F = Foot- and flange-mounted motor. Special flange.H = Foot- and flange-mounted motor. Large flange with

clearance holes.J = Foot- and flange-mounted motor. Small flange with

tapped holes.V = Flange-mounted motor. Special flange.

Position 13Voltage and frequencySee appropriate pages with tables

Position 14VersionA = Generation code followed by variant codes

Explanation of the pr oduct code

11 = 11213 = 13216 = 16018 = 18020 = 200

22 = 22525 = 250

12 ABB Motors

Total ly enclosed squirrel cagethree phase moto rs, aluminium frameIP 55 IC 411

Effi- PowerOutput Motor type Product code Speed ciency factorkW M2AA 3GAA r/min % cos ϕ A I

NNm T

NT

N

3000 r/min = 2 poles Basic design

0.25 63 B 061 001- 2820 70.6 0.75 0.70 4.0 0.85 2.2 2.70.25 63 B1) 061 002- 2820 70.6 0.75 0.70 4.0 0.85 2.2 2.7

0.37 71 A 071 001- 2840 72.7 0.80 0.93 4.5 1.25 2.2 2.70.55 71 B 071 002- 2850 76.1 0.80 1.33 5.0 1.9 2.2 2.7

0.75 80 A 081-001- 2860 78.8 0.82 1.7 5.0 2.5 2.2 2.71.1 80 B 081 002- 2870 80.1 0.85 2.4 5.5 3.7 2.4 3.0

1.5 90 S 091 001- 2870 80.1 0.82 3.35 5.5 5.0 2.4 3.02.2 90 L 091 002- 2870 82.8 0.86 4.55 7.0 7.5 2.7 3.43 100 L 101 001- 2900 83.8 0.88 5.95 7.5 10.0 2.7 3.6

4 112 M 111 001- 2850 86 0.91 7.4 7.5 13.4 2.8 3.05.5 132 SA 131 001- 2855 86 0.88 10.5 7.8 18.4 3.2 3.47.5 132 SB 131 002- 2855 87 0.90 13.9 8.5 25.1 3.4 3.6

11 160 MA 161 001- 2930 91.2 0.88 20.0 6.3 36 1.9 2.515 160 M 161 002- 2920 91.7 0.90 26.5 6.6 49 2.3 2.5

18.5 160 L 161 003- 2920 92.4 0.91 32 7.3 60 2.6 2.722 180 M 181 001- 2930 92.8 0.89 38.5 7.2 71 2.5 2.7

30 200 MLA 201 001- 2955 93.2 0.88 53 7.3 97 2.4 3.137 200 MLB 201 002- 2950 93.6 0.89 64 7.3 120 2.5 3.2

45 225 SMB 221 001- 2960 93.9 0.88 79 7.3 145 2.5 2.855 250 SMA 251 001- 2970 94.4 0.89 95 7.5 177 2.0 3.0

3000 r/min = 2 poles High-output design 2)

0.753) 71 C 071 003- 2820 77.1 0.80 1.75 5.0 2.5 2.2 2.71.53) 80 C 081 003- 2840 80.1 0.87 3.15 5.5 5.0 2.3 2.8

2.73)4) 90 LB 091 003- 2860 80.7 0.86 5.7 7.0 9.0 2.6 3.243) 100 LB 101 002- 2900 84.1 0.86 8.1 7.5 13.0 2.7 3.6

5.53) 112 MB 111 002- 2855 86.5 0.93 9.9 7.3 18.4 2.7 2.9113) 132 SC 131 003- 2835 87.0 0.93 19.6 8.0 37 3.2 3.3

223) 160 LB 161 004- 2920 92.1 0.91 38 7.1 72 2.6 2.6303) 180 LB 181 002- 2945 93.7 0.89 53 8.3 97 3.1 3.4

45 200 MLC 201 003- 2950 93.8 0.89 78 7.3 146 2.6 3.355 225 SMC 221 002- 2960 94.3 0.89 95 7.0 177 2.5 2.975 250 SMB 251 002- 2970 95.2 0.90 127 7.3 241 2.1 3.0

1) On request.

TmaxI

N

Current

IS

TN

TS

Torque

400 V 50 Hz

The bullet indicates a 3-letter product code supplement for choice of mounting arrangement(page 11, pos. 12), voltage and frequency (below) and generation code (page 11, pos. 14).

Code letters for supplementing the product codeCode letter for voltage and frequencyDirect start or, with D-connection, also Y/D-start

Motor S D H E F T U X

size 50 Hz 60 Hz 50 Hz 60 Hz 50 Hz 50 Hz 50 Hz 50 Hz 50 Hz

63-100 220-240 V∆ 380-420 V∆ 440-480 V∆ - 500 V∆ 500 VY 660 V∆ 1) 690 V∆1)

380-420 VY 440-480 VY 660-690 VY -112-132 220-240 V∆ - 380-420 V∆ 440-480 V∆ 415 V∆ 500 V∆ 660 V∆ 690 V∆

380-420 VY 440-480 VY 660-690 VY -160-250 220, 230 V∆ - 380,400,415V∆ 440 V∆ 415 V∆ 500 V∆ 660 V∆ 690 V∆

380,400,415 VY 440 VY 660, 690 VY −

Other ratedvoltage,connectionor frequency,690 V maximum

1) Shaft Ø14 mm, large flange F 130.2) High-output design

The output of these motors is one step higher than the basic designwith rated outputs in accordance with CENELEC. Motor sizes 112 to 132 aresomewhat longer than the basic design.

3) Temperature rise class F.4) Lower than CENELEC +1.

13ABB Motors

Recalculation factorsRecalculation factors for current at rated voltages other than 400 V 50 Hz

Rated voltage at 50 Hzand motor wound for Recalculation factor

220 V 1.82230 V 1.74415 V 0.96

500 V 0.80660 V 0.61690 V 0.58

380 V 50 Hz 415 V 50 Hz

Insulation class FTemperature rise class B


3) Temperature rise class F.4) Lower than CENELEC +1.


Moment Weight SoundEffi- Power Current Effi- Power Current of inertia Foot-mounted pressure level

Output Speed ciency factor IN

Speed ciency factor IN

J = 1/4 GD2 motor LpkW r/min % cos ϕ A r/min % cos ϕ A kgm2 kg dB(A)

0.25 2790 70.7 0.79 0.70 2830 69.7 0.69 0.72 0.00018 4.5 480.25 2790 70.7 0.79 0.70 2830 69.7 0.69 0.72 0.00018 4.5 48

0.37 2830 72.5 0.84 0.93 2860 72.4 0.77 0.95 0.0004 5.5 550.55 2830 76 0.84 1.32 2870 75.3 0.75 1.37 0.0005 6.5 55

0.75 2840 77.9 0.85 1.73 2880 78.6 0.8 1.7 0.0009 9 581.1 2850 79.3 0.88 2.43 2890 80.1 0.81 2.42 0.0011 10 58

1.5 2850 79.7 0.88 3.40 2890 79.8 0.79 3.4 0.0019 13 632.2 2850 81.8 0.89 4.70 2890 82.9 0.82 4.57 0.0024 16 633 2890 82.9 0.90 6.2 2910 84.1 0.85 5.95 0.0041 21 68

4 2830 85.0 0.92 7.80 2865 86.5 0.90 7.2 0.010 25 635.5 2835 85.0 0.90 10.9 2870 86.5 0.87 10.2 0.014 37 697.5 2835 86.0 0.91 14.7 2870 87.5 0.88 13.6 0.016 42 69

11 2915 90.8 0.89 20.5 2935 91.3 0.86 19.4 0.039 73 6915 2905 91.2 0.90 27.5 2925 92.0 0.89 25.5 0.047 84 69

18.5 2910 92.0 0.91 33.5 2930 92.6 0.90 31 0.053 94 6922 2930 92.4 0.90 40.5 2945 93.0 0.88 37.5 0.077 119 69

30 2955 93.1 0.89 55 2960 93.3 0.86 52 0.15 175 7237 2950 93.4 0.89 68 2955 93.7 0.87 63 0.18 200 72

45 2955 93.7 0.89 82 2965 93.9 0.87 77 0.26 235 7455 2960 94.3 0.89 100 2970 94.5 0.88 92 0.49 285 75

0.753) 2800 76.8 0.85 1.8 2840 77.7 0.77 1.8 0.0006 7.5 551.53) 2820 78.6 0.88 3.3 2860 80.6 0.84 3.15 0.0013 11 58

2.73)4) 2840 80.2 0.89 5.8 2870 80.6 0.83 5.7 0.0027 18 6343) 2890 83.9 0.88 8.3 2910 85.8 0.84 7.8 0.005 25 68

5.53) 2835 85.5 0.93 10.5 2865 87.5 0.92 9.5 0.012 33 63113) 2815 86.5 0.92 21 2845 88.0 0.92 18.9 0.022 56 69

223) 2910 91.6 0.91 40 2925 92.4 0.90 37 0.058 100 69303) 2940 93.5 0.90 55 2950 93.8 0.87 52 0.092 137 70

45 2935 93.5 0.89 82 2955 93.8 0.88 76 0.19 205 7255 2950 94.2 0.89 100 2965 94.3 0.88 92 0.29 260 7475 2965 95.0 0.90 134 2970 95.3 0.89 123 0.57 330 75

14 ABB Motors

400 V 50 Hz

Current Torque

TN

TS

Tmax

IS

IN

1) On request.




63-100 220-240 V∆ 380-420 V∆ 440-480 V∆ - 500 V∆ 500 VY 660 V∆ 1) 690 V∆1)

380-420 VY 440-480 VY 660-690 VY -112-132 220-240 V∆ - 380-420 V∆ 440-480 V∆ 415 V∆ 500 V∆ 660 V∆ 690 V∆

380-420 VY 440-480 VY 660-690 VY -160-250 220, 230 V∆ - 380,400,415V∆ 440 V∆ 415V∆ 500 V∆ 660 V∆ 690V∆

380,400,415 VY 440 VY 660, 690 VY −



1) Shaft Ø14 mm, large flange F 130. 2) High-output design The output of these motors is one step higher than the basic design with rated outputs in accordancewith CENELEC. Motor sizes 112 to 132 are somewhat longer than the basic design. 3) Temperature rise class F. 4) Lower than CENELEC +1.


Effi- PowerOutput Motor type Product code Speed ciency factorkW M2AA 3GAA r/min % cos ϕ A IN Nm TN TN


0.18 63 B 062 001- 1370 58.7 0.63 0.72 3.0 1.25 2.2 2.60.18 63 B1) 062 002- 1370 58.7 0.63 0.72 3.0 1.25 2.2 2.6

0.25 71 A 072 001- 1400 66.8 0.67 0.83 3.5 1.7 2.2 2.70.37 71 B 072 002- 1410 70.5 0.69 1.12 4.0 2.5 2.2 2.7

0.55 80 A 082 001- 1420 74 0.73 1.45 4.0 3.7 2.2 2.70.75 80 B 082 002- 1420 77 0.74 1.9 4.5 5.0 2.2 2.7

1.1 90 S 092 001- 1410 77.5 0.81 2.59 5.0 7.5 2.2 2.71.5 90 L 092 002- 1420 80.3 0.79 3.45 5.0 10.0 2.4 2.9

2.2 100 LA 102 001- 1430 81.7 0.81 4.8 5.5 15.0 2.4 2.93 100 LB 102 002- 1430 83.5 0.81 6.48 5.5 20.0 2.5 2.9

4 112 M 112 001- 1435 84.5 0.80 8.6 7.0 26.6 2.9 3.15.5 132 S 132 001- 1450 87.0 0.83 11.1 7.3 36.2 2.2 3.07.5 132 M 132 002- 1450 88.0 0.83 14.8 7.9 49.4 2.5 3.2

11 160 M 162 001- 1460 90.3 0.81 21.5 6.7 72 2.9 2.815 160 L 162 002- 1455 91.1 0.84 28.5 6.8 98 3.0 2.8

18.5 180 M 182 001- 1470 92.3 0.84 35 7.0 120 3.1 2.722 180 L 182 002- 1470 92.4 0.83 41 7.0 143 2.9 2.8

30 200 MLA 202 001- 1475 92.9 0.83 56 6.7 194 2.6 2.837 225 SMA 222 001- 1480 93.6 0.84 68 6.6 239 2.4 2.5

45 225 SMB 222 002- 1480 94.2 0.83 83 6.7 290 2.7 2.655 250 SMA 252 001- 1480 94.6 0.86 98 7.5 355 2.3 2.8


0.553) 71 C 072 003- 1380 72.5 0.73 1.5 4.0 3.7 2.2 2.41.13) 80 C 082 003- 1380 76.1 0.80 2.65 4.5 7.5 2.0 2.2

1.853)4) 90 L 092 003- 1390 79.5 0.80 4.4 4.5 13.0 2.2 2.42.23) 90 LB 092 004- 1390 80.3 0.83 4.85 4.5 15.0 2.2 2.443) 100 LC 102 003- 1420 82.7 0.82 8.73 5.5 27.0 2.5 2.8

5.53) 112 MB 112 002- 1425 84.5 0.83 11.4 7.1 36.9 2.8 3.1113) 132 MB 132 003- 1450 88.0 0.86 21 8.3 72.4 3.0 2.7

18.53) 160 LB 162 003- 1450 90.5 0.84 36 6.9 122 2.9 2.9303) 180 LB 182 003- 1465 92.5 0.84 56 6.9 195 3.2 2.8

37 200 MLB 202 002- 1475 93.4 0.84 68 7.8 236 3.6 3.255 225 SMC 222 003- 1480 94.6 0.84 100 7.3 355 3.1 2.875 250 SMB 252 002- 1480 95.0 0.86 132 7.0 484 2.4 3.0

15ABB Motors



220 V 1.82230 V 1.74415 V 0.96

500 V 0.80660 V 0.61690 V 0.58

380 V 50 Hz 415 V 50 Hz




3) Temperature rise class F.4) Lower than CENELEC + 1.





0.18 1370 60.6 0.68 0.68 1370 56.9 0.60 0.75 0.00028 4.5 370.18 1370 60.6 0.68 0.68 1370 56.9 0.60 0.75 0.00028 4.5 37

0.25 1400 67.9 0.72 0.80 1410 65.4 0.63 0.89 0.00073 5.5 450.37 1400 70.8 0.74 1.11 1420 69.7 0.66 1.15 0.00098 6.5 45

0.55 1410 73.6 0.78 1.45 1420 73.5 0.70 1.48 0.0017 9 480.75 1410 76.4 0.78 1.90 1430 76.7 0.70 1.95 0.0021 10 48

1.1 1410 76.3 0.83 2.66 1430 77.7 0.76 2.60 0.0032 13 501.5 1420 79.9 0.82 3.5 1430 80.3 0.77 3.45 0.0043 16 50

2.2 1430 80.6 0.85 4.96 1430 81.8 0.78 4.85 0.0069 21 543 1430 82.6 0.85 6.61 1430 83.1 0.77 6.55 0.0082 24 54

4 1425 84.0 0.83 8.7 1440 85.0 0.75 8.80 0.015 27 565.5 1445 86.0 0.85 11.5 1455 87.5 0.81 10.9 0.031 40 597.5 1445 87.0 0.86 15.3 1455 88.0 0.82 14.5 0.038 48 59

11 1450 89.9 0.83 22.5 1465 90.5 0.79 21.5 0.067 75 6215 1445 90.6 0.84 30.0 1460 91.4 0.83 28 0.091 94 62

18.5 1465 91.7 0.85 36.0 1470 92.2 0.83 34.0 0.161 124 6222 1465 92.1 0.85 42.5 1475 92.6 0.82 40.0 0.191 141 63

30 1470 92.6 0.83 59 1475 93.0 0.83 54 0.29 180 6337 1475 93.4 0.84 72 1480 93.7 0.81 68 0.37 215 66

45 1475 94.0 0.85 86 1480 94.2 0.81 82 0.42 230 6655 1475 94.3 0.86 103 1480 94.7 0.84 96 0.72 275 67

0.553) 1370 71.9 0.78 1.51 1390 72.5 0.68 1.55 0.0012 7.5 451.13) 1370 73.7 0.84 2.76 1400 76.8 0.76 2.6 0.0024 11 48

1.853)4) 1380 78.8 0.83 4.4 1400 79.5 0.76 4.35 0.0043 16 502.23) 1380 78.4 0.85 5.1 1400 80.8 0.80 4.9 0.0048 17 5043) 1410 81.5 0.85 8.89 1420 82.9 0.77 8.8 0.009 25 54

5.53) 1415 84.5 0.85 11.7 1430 85.5 0.79 11.4 0.018 34 56113) 1445 87.5 0.87 22 1455 88.5 0.83 21 0.048 59 59

18.53) 1440 89.8 0.85 37 1450 90.8 0.83 34 0.102 103 63303) 1465 92.2 0.85 58 1470 92.7 0.82 55 0.225 161 63

37 1475 93.3 0.85 71 1475 93.3 0.82 67 0.34 205 6355 1475 94.5 0.84 105 1480 94.6 0.82 99 0.49 265 6675 1475 94.5 0.87 139 1480 95.1 0.86 128 0.88 335 67

16 ABB Motors


Effi- PowerOutput Motor type Product code Speed ciency factorkW M2AA 3GAA r/min % cos ϕ A I

NNm T

NT

N


0.12 71 073 001- 930 55.4 0.56 0.59 2.5 1.2 2.3 2.70.18 71 A 073 002- 920 57.8 0.62 0.75 2.5 1.9 2.0 2.40.25 71 B 073 003- 920 62 0.64 0.92 3.0 2.6 2.0 2.4

0.37 80 A 083 001- 920 68 0.66 1.25 3.5 3.8 2.1 2.50.55 80 B 083 002- 930 69.8 0.67 1.78 3.5 5.7 2.1 2.5

0.75 90 S 093 001- 930 71.5 0.67 2.36 4.0 7.5 1.9 2.31.1 90 L 093 002- 930 74.4 0.69 3.25 4.0 11.0 1.9 2.31.5 100 L 103 001- 950 78.2 0.69 4.1 4.5 15.0 1.9 2.3

2.2 112 M 113 001- 940 80.5 0.74 5.4 5.6 22.3 2.1 2.73 132 S 133 001- 960 84.5 0.75 6.9 6.1 29.8 2.4 2.64 132 MA 133 002- 960 85.5 0.78 8.7 7.1 39.7 2.6 2.85.5 132 MB 133 003- 955 86.0 0.78 11.9 6.9 55 2.8 2.8

7.5 160 M 163 001- 970 89.3 0.79 15.4 6.7 74 2.0 2.811 160 L 163 002- 970 89.8 0.78 23.0 7.1 109 2.2 2.915 180 L 183 001- 970 90.8 0.78 31.0 7.0 148 2.1 3.0

18.5 200 MLA 203 001- 985 91.1 0.81 36 7.0 179 2.5 2.722 200 MLB 203 002- 980 91.7 0.81 43 7.2 214 2.5 2.730 225 SMB 223 001- 985 92.8 0.83 56 6.6 291 2.5 2.737 250 SMA 253 001- 985 93.7 0.83 69 7.3 359 2.8 2.8


0.373) 71 C 073 004- 890 63 0.70 1.27 3.0 3.8 1.7 1.90.753) 80 C 083 003- 910 71.5 0.70 2.27 3.5 7.5 1.9 2.2

1.31)3) 90 LB 093 003- 910 72.4 0.71 3.85 4.0 13.5 1.9 2.22.23) 100 LC 103 002- 940 79 0.71 5.8 4.5 22.0 1.9 2.3

33) 112 MB 113 002- 935 80.0 0.76 7.2 5.5 30.6 2.4 2.76.51) 3) 132 MC 133 004- 960 85.0 0.75 14.8 6.6 64.7 2.3 2.7

141)3) 160 LB 163 003- 960 89.1 0.77 29.5 7.6 139 2.7 3.118.53) 180 LB 183 002- 965 90.6 0.79 37.5 6.2 183 2.0 2.6

30 200 MLC 203 003- 980 91.7 0.81 56 7.5 292 3.3 3.037 225 SMC 223 002- 985 93.2 0.83 69 7.7 359 3.1 3.045 250 SMB 253 002- 985 94.1 0.84 82 7.3 436 2.8 2.8

400 V 50 Hz

Current Torque

TmaxIN IS

TN

TS

1) On request.




63-100 220-240 V∆ 380-420 V∆ 440-480 V∆ - 500 V∆ 500 VY 660 V∆ 1) 690 V∆1)

380-420 VY 440-480 VY 660-690 VY -112-132 220-240 V∆ - 380-420 V∆ 440-480 V∆ 415 V∆ 500 V∆ 660 V∆ 690 V∆

380-420 VY 440-480 VY 660-690 VY -160-250 220, 230 V∆ - 380,400,415V∆ 440 V∆ 415 V∆ 500 V∆ 660 V∆ 690 V∆

380,400,415 VY 440 VY 660, 690 VY −



1) Lower than CENELEC +1.2) High-output design


3) Temperature rise class F.

17ABB Motors


415 V 50 Hz380 V 50 Hz




220 V 1.82230 V 1.74415 V 0.96

500 V 0.80660 V 0.61690 V 0.58


1) Lower than CENELEC +1.3) Temperature rise class F.





0.12 920 58.2 0.60 0.56 940 53.5 0.54 0.61 0.0007 5.0 360.18 910 59.2 0.66 0.72 930 56.2 0.59 0.77 0.0007 5.5 360.25 910 62.6 0.68 0.9 930 61.1 0.61 0.95 0.0009 6.5 36

0.37 910 68.4 0.69 1.22 930 67.3 0.62 1.28 0.0017 8.5 430.55 920 69.8 0.72 1.72 930 69.2 0.64 1.78 0.0021 9.5 43

0.75 920 70.6 0.72 2.3 930 70.6 0.64 2.36 0.0032 13 441.1 920 73.9 0.73 3.2 930 74.2 0.66 3.25 0.0043 16 441.5 940 77.8 0.74 4.1 960 78.4 0.67 4.1 0.0082 23 49

2.2 930 80.0 0.78 5.4 950 80.5 0.71 5.4 0.015 27 543 955 84.0 0.77 7.1 965 84.0 0.72 6.9 0.031 39 614 955 85.0 0.81 8.9 965 85.5 0.76 8.6 0.038 46 615.5 950 85.5 0.81 12.2 960 86.0 0.76 11.8 0.045 54 61

7.5 960 88.7 0.80 16.1 970 89.6 0.77 15.1 0.089 88 5911 960 89.4 0.80 23.5 970 90.0 0.76 22.4 0.107 102 5915 970 90.9 0.79 32 975 91.1 0.74 31.0 0.217 151 59

18.5 980 90.8 0.81 38 985 91.1 0.78 36 0.37 165 6322 980 91.6 0.81 45 985 91.8 0.79 42 0.43 185 6330 985 92.6 0.83 59 985 92.9 0.82 55 0.64 225 6337 985 93.5 0.84 72 990 93.8 0.81 67 1.16 280 63

0.373) 870 62.5 0.74 1.25 900 62.5 0.66 1.3 0.0012 7.5 360.753) 900 71.4 0.74 2.21 920 71.6 0.66 2.3 0.0024 11 43

1.33) 900 71.5 0.75 3.8 920 72.4 0.67 3.8 0.0048 18 442.23) 930 77.9 0.75 5.85 940 78.8 0.67 5.9 0.009 26 49

31)3) 925 79.5 0.79 7.3 940 80.0 0.73 7.2 0.018 33 546.51) 3) 955 85.0 0.79 14.8 965 84.5 0.71 15.1 0.049 59 61

141)3) 955 88.7 0.79 30.5 965 89.2 0.75 29.2 0.127 117 6218.53) 965 90.0 0.81 39 965 90.8 0.78 36.5 0.237 160 59

30 980 91.5 0.83 57 985 91.9 0.83 53 0.49 200 6337 980 93.0 0.83 72 985 93.2 0.81 68 0.75 252 6345 985 93.8 0.86 85 985 94.2 0.83 80 1.49 320 63

18 ABB Motors


Effi- PowerOutput Motor type Product code Speed ciency factorkW M2AA 3GAA r/min % cos ϕ A IN Nm TN TN


0.055 63 B 064 002- 650 32.2 0.62 0.44 1.5 0.8 1.6 2.00.09 71 A 074 001- 680 43.4 0.63 0.53 2.0 1.3 1.7 2.00.12 71 B 074 002- 680 48.6 0.59 0.63 2.0 1.8 1.7 2.0

0.18 80 A 084 001- 700 54.4 0.56 0.90 2.5 2.5 1.8 2.30.25 80 B 084 002- 700 58.6 0.55 1.18 2.5 3.4 1.9 2.4

0.37 90 S 094 001- 700 61.5 0.56 1.60 3.0 5.0 1.9 2.40.55 90 L 094 002- 700 62.9 0.57 2.35 3.0 7.5 1.9 2.4

0.75 100 LA 104 001- 700 72.9 0.59 2.67 3.5 10.0 2.1 2.71.1 100 LB 104 002- 700 74 0.64 3.42 3.5 15.0 2.1 2.7

1.5 112M 114 001- 695 74.5 0.65 4.5 4.1 20.6 1.9 2.42.2 132S 134 001- 720 80.5 0.67 5.9 5.3 29.2 1.9 2.53 132M 134 002- 720 82.0 0.68 7.8 5.5 39.8 2.4 2.6

4 160 MA 164 001- 715 84.1 0.69 10.0 5.2 54 2.1 2.45.5 160 M 164 002- 710 84.7 0.70 13.4 5.4 74 2.4 2.67.5 160 L 164 003- 715 86.3 0.70 18.1 5.4 100 2.4 2.811 180 L 184 001- 720 88.7 0.76 23.5 5.9 146 2.4 2.6

15 200 MLA 204 001- 740 91.1 0.82 29 7.4 194 1.8 3.018.5 225 SMA 224 001- 730 91.1 0.79 37 6.2 242 1.9 2.722 225 SMB 224 002- 730 91.5 0.77 45 6.0 288 1.9 2.730 250 SMA 254 001- 735 92.8 0.79 59 6.9 390 1.9 2.9


0.183) 71 C 074 003- 660 51.3 0.64 0.85 2.0 2.5 1.6 1.90.373) 80 C 084 003- 680 58.2 0.60 1.60 3.0 5.0 1.7 1.9

0.753) 90 LB 094 003- 680 66.9 0.65 2.6 3.0 10.0 1.8 2.11.53) 100 LC 104 003- 700 74 0.66 4.6 3.5 21.0 1.8 2.2

21) 3) 112 MB 114 002- 685 73.5 0.67 5.9 4.4 27.9 1.9 2.23.81) 3) 132 MB 134 003- 710 80.5 0.69 9.9 5.2 51.1 2.0 2.3

8.51) 3) 160 LB 164 004- 700 83.5 0.70 21.0 5.1 115 2.4 2.5153) 180 LB 184 002- 720 88.0 0.76 32.5 6.0 199 2.5 2.6

18.5 200 MLB 204 002- 745 91.4 0.81 36 6.7 237 1.7 2.830 225 SMC 224 003- 735 91.8 0.79 60 7.2 390 2.1 3.337 250 SMB 254 002- 735 93.2 0.81 71 7.2 481 2.0 2.9

400 V 50 Hz

1) On request.

TmaxIN IS

TN

TS

Current Torque





63-100 220-240 V∆ 380-420 V∆ 440-480 V∆ - 500 V∆ 500 VY 660 V∆ 1) 690 V∆1)

380-420 VY 440-480 VY 660-690 VY -112-132 220-240 V∆ - 380-420 V∆ 440-480 V∆ 415 V∆ 500 V∆ 660 V∆ 690 V∆

380-420 VY 440-480 VY 660-690 VY -160-250 220, 230 V∆ - 380,400,415V∆ 440 V∆ 415 V∆ 500 V∆ 660 V∆ 690 V∆

380,400,415 VY 440 VY 660, 690 VY −


1) Lower than CENELEC +1.2) High-output design


3) Temperature rise class F.

19ABB Motors

415 V 50 Hz380 V 50 Hz

Insulation c lass FTemperature rise c lass B




220 V 1.82230 V 1.74415 V 0.96

500 V 0.80660 V 0.61690 V 0.58


1) Lower than CENELEC +1.3) Temperature rise class F.





0.055 650 33.6 0.65 0.43 660 30.8 0.61 0.46 0.00028 4.5 320.09 670 44.7 0.66 0.50 690 42 0.60 0.55 0.0007 5.5 390.12 670 49.9 0.64 0.60 690 47.2 0.57 0.65 0.0009 6.5 39

0.18 690 55.4 0.59 0.85 700 53.5 0.53 0.95 0.0017 8.5 440.25 690 60 0.58 1.15 700 57.3 0.51 1.22 0.0021 9.5 44

0.37 690 62.7 0.59 1.57 700 60.5 0.54 1.7 0.0032 13 430.55 690 64.9 0.59 2.27 700 61.5 0.55 2.43 0.0043 16 43

0.75 690 72.9 0.61 2.59 700 71.1 0.55 2.78 0.0069 20 461.1 700 73.8 0.68 3.38 710 73.1 0.60 3.5 0.0082 23 46

1.5 685 74.0 0.69 4.5 700 74.0 0.62 4.6 0.016 28 522.2 715 80.0 0.71 5.9 725 80.0 0.65 5.9 0.038 46 563 715 82.0 0.72 7.8 720 82.0 0.66 7.8 0.045 53 56

4 710 83.8 0.71 10.2 720 84.5 0.66 9.9 0.072 75 595.5 705 84.0 0.72 13.8 715 85.0 0.68 13.3 0.091 88 597.5 710 85.7 0.72 18.6 715 86.6 0.68 17.8 0.131 118 5911 715 88.2 0.77 24.5 720 89.0 0.75 23.0 0.224 147 59

15 735 91.0 0.83 30 740 91.2 0.79 29 0.45 175 6018.5 730 91.0 0.79 39 735 91.3 0.76 36 0.61 210 6322 730 91.4 0.81 45 735 91.5 0.76 44 0.68 225 6330 735 92.6 0.81 61 740 92.9 0.77 58 1.25 280 63

0.183) 650 51.4 0.68 0.85 670 50.4 0.61 0.87 0.0012 7.5 390.373) 670 59.6 0.64 1.55 690 57.3 0.57 1.65 0.0024 11 44

0.753) 670 66.8 0.69 2.55 690 66.5 0.61 2.65 0.0048 18 431.53) 690 73.8 0.70 4.52 700 73.6 0.62 4.7 0.009 26 46

21) 3) 675 73.0 0.71 5.9 690 73.5 0.64 6.0 0.018 33 523.81)3) 705 80.0 0.72 10 715 80.5 0.67 9.9 0.049 59 56

8.51)3) 695 81.7 0.73 21.5 705 83.8 0.68 21.0 0.131 118 62153) 715 87.6 0.78 33.5 720 88.3 0.74 32.0 0.240 155 62

18.5 735 91.2 0.83 37 735 91.6 0.79 35 0.54 200 6030 730 91.7 0.80 62 735 91.9 0.77 61 0.80 255 6337 735 92.5 0.82 74 735 93.2 0.81 71 1.52 320 63

20 ABB Motors

Output in kW Motor type Product code 380-420 V 440-480 V50 Hz 60 Hz M2AA 3GAA 50 Hz 60 Hz 50 Hz 60 Hz 50 Hz 60 Hz

3000/3600 r/min = 2 poles Basic design

0.25 0.3 63 B 061 001- 0.75 0.75 2820 3370 0.74 0.750.25 0.3 63 B1) 061 002- 0.75 0.75 2820 3370 0.74 0.750.37 0.45 71 A 071 001- 1.0 1.0 2840 3410 0.80 0.790.55 0.65 71 B 071 002- 1.4 1.4 2850 3410 0.80 0.79

0.75 0.9 80 A 081 001- 1.8 1.8 2860 3440 0.82 0.821.1 1.3 80 B 081 002- 2.5 2.5 2870 3450 0.85 0.83

1.5 1.75 90 S 091 001- 3.5 3.5 2870 3460 0.84 0.822.2 2.5 90 L 091 002- 4.7 4.7 2870 3470 0.86 0.853.0 3.5 100 L 101 001- 6.2 6.2 2900 3470 0.88 0.86

4.0 4.6 112 M 111 001- 7.8 7.7 2850 3450 0.91 0.915.5 6.4 132 SA 131 001- 10.9 10.9 2855 3455 0.88 0.887.5 8.6 132 SB 131 002- 14.7 14.4 2855 3455 0.90 0.90

3000/3600 r/min = 2 poles High-output design

0.75 0.9 71 C3) 071 003- 1.9 1.9 2820 3410 0.80 0.791.5 1.75 80 C3) 081 003- 3.4 3.4 2840 3430 0.84 0.84

2.7 3 90 LB 3) 091 003- 5.8 5.8 2860 3470 0.86 0.854 4.6 100 LB 3) 101 002- 8.3 8.3 2900 3470 0.86 0.85

5.5 6.4 112 MB 111 002- 10. 5 10.4 2855 3455 0.93 0.9311 12.6 132 SC 131 003- 21 20 2835 3435 0.93 0.93

Data at volta ge rang esRated data at v olta ge codes S and DSingle-speed motors of size 63 to 180 can be producedwith voltage codes S and D, i.e., voltage range at both50 and 60 Hz. The current rating for each voltage rangeis specified on the rating plate. It represents the highest

current that can exist within the voltage range at therated output. The power factor and speed specified onthe rating plate apply at the average voltage within therange.

Current in A2) at Speedr/min Power factor cos ϕ

1) Shaft Ø14 mm, large flange F 130.2) Recalculation factors

Multiply by 1.73 when recalculating:from 380-420 V to 220-240 V 50 Hzfrom 440-480 V to 250-280 V 60 Hz

3) Class F temperature rise


0.18 0.22 63 B 062 001- 0.8 0.8 1370 1660 0.64 0.640.18 0.22 63 B1) 062 002- 0.8 0.8 1370 1660 0.64 0.640.25 0.30 71 A 072 001- 0.90 0.90 1400 1690 0.67 0.670.37 0.45 71 B 072 002- 1.2 1.2 1410 1690 0.70 0.70

0.55 0.65 80 A 082 001- 1.5 1.5 1420 1700 0.74 0.730.75 0.90 80 B 082 002- 2.0 2.0 1420 1700 0.74 0.75

1.1 1.30 90 S 092 001- 2.7 2.7 1410 1700 0.79 0.791.5 1.75 90 L 092 002- 3.5 3.5 1420 1710 0.79 0.78

2.2 2.5 100 LA 102 001- 5.0 5.0 1430 1720 0.81 0.793.0 3.5 100 LB 102 002- 6.6 6.6 1430 1720 0.81 0.79

4.0 4.6 112 M 112 001- 8.9 8.6 1435 1735 0.80 0.815.5 6.4 132 S 132 001- 11.5 11.5 1450 1750 0.83 0.837.5 8.6 132 M 132 002- 15.3 15.1 1450 1750 0.83 0.83


0.55 0.65 71 C3) 072 003- 1.6 1.6 1380 1670 0.73 0.731.1 1.3 80 C3) 082 003- 2.8 2.8 1380 1680 0.80 0.80

1.85 2.2 90 L 3) 092 003- 4.4 4.4 1400 1690 0.80 0.792.2 2.5 90 LB3) 092 004- 5.1 5.1 1390 1690 0.81 0.804.0 4.6 100 LC 102 003- 8.9 8.9 1420 1710 0.79 0.78

5.5 6.4 112 MB 112 002- 11.7 11.6 1425 1725 0.83 0.8311 12.6 132 MB 132 003- 22 22 1450 1750 0.86 0.86

21ABB Motors

Output in kW Motor type Product code 380-420 V 440-480 V50 Hz 60 Hz M2AA 3GAA 50 Hz 60 Hz 50 Hz 60 Hz 50 Hz 60 Hz


0.12 0.15 71 073 001- 0.65 0.65 930 1120 0.58 0.590.18 0.22 71 A 073 002- 0.80 0.80 920 1110 0.62 0.620.25 0.30 71 B 073 002- 0.95 0.95 920 1110 0.64 0.65

0.37 0.45 80 A 083 001- 1.3 1.3 920 1120 0.66 0.660.55 0.65 80 B 083 002- 1.8 1.8 930 1120 0.68 0.640.75 0.9 90 S 093 001- 2.4 2.4 930 1120 0.67 0.68

1.1 1.3 90 L 093 002- 3.3 3.3 930 1120 0.69 0.671.5 1.75 100 L 103 001- 4.2 4.2 950 1130 0.71 0.69

2.2 2.5 112 M 113 001- 5.4 5.3 940 1140 0.74 0.743.0 3.5 132 S 133 001- 7.1 7.0 960 1160 0.75 0.754.0 4.6 132 MA 133 002- 8.9 8.9 960 1160 0.78 0.785.5 6.4 132 MB 133 003- 12.2 12.2 955 1155 0.78 0.78


0.37 0.45 71 C2) 073 004- 1.3 1.3 890 1080 0.70 0.700.75 0.9 80 C2) 083 003- 2.3 2.3 910 1100 0.70 0.68

1.3 1.5 90 LB 2) 093 003- 3.9 3.9 910 1110 0.71 0.702.2 2.5 100 LC2) 103 002- 5.9 5.9 940 1130 0.71 0.69

3.0 3.5 112 MB 113 002- 7.3 7.3 935 1135 0.76 0.756.5 7.5 132 MC 133 004- 15.2 14.9 960 1160 0.75 0.76

current that can exist within the voltage range at therated output. The power factor and speed specified onthe rating plate apply at the average voltage within therange.

Current in A1) at Speedr/min Power factor cos ϕ


0.055 0.07 63 B 064 002- 0.5 0.5 650 770 0.62 0.630.09 0.11 71 A 074 001- 0.55 0.55 680 780 0.63 0.640.12 0.15 71 B 074 002- 0.7 0.7 680 780 0.61 0.62

0.18 0.22 80 A 084 001- 1.0 1.0 700 840 0.56 0.540.25 0.30 80 B 084 002- 1.25 1.25 700 840 0.55 0.54

0.37 0.45 90 S 094 001- 1.7 1.7 700 850 0.56 0.560.55 0.65 90 L 094 002- 2.5 2.5 700 850 0.57 0.57

0.75 0.9 100 LA 104 001- 2.8 2.8 700 850 0.59 0.601.1 1.3 100 LB 104 002- 3.5 3.5 700 850 0.64 0.65

1.5 1.7 112 M 114 001- 4.6 4.4 695 845 0.65 0.652.2 2.5 132 S 134 001- 5.9 5.9 720 870 0.67 0.663.0 3.5 132 M 134 002- 7.8 7.8 720 870 0.68 0.68


0.18 0.22 71 C2) 074 003- 0.95 0.95 660 780 0.64 0.620.37 0.45 80 C2) 084 003- 1.7 1.7 680 820 0.60 0.60

0.75 0.90 90 LB 2) 094 003- 2.7 2.7 680 830 0.65 0.651.5 1.75 100 LC2) 104 003- 4.8 4.8 700 840 0.66 0.66

2.0 2.3 112 MB 114 002- 6 6 685 835 0.67 0.663.8 4.4 132 MB 134 003- 10 10 710 860 0.69 0.69

1) Recalculation factors.Multiply by 1.73 when recalculating:

from 380-420 V to 220-240 V 50 Hzfrom 440-480 V to 250-280 V 60 Hz

2) Class F temperature rise

Data at volta ge rang esRated data at v olta ge codes S and DSingle-speed motors of size 63 to 180 can be producedwith voltage codes S and D, i.e., voltage range at both50 and 60 Hz. The current rating for each voltage rangeis specified on the rating plate. It represents the highest

22 ABB Motors

Totall y enc losed squirrel ca ge three phase motor s, aluminium frameIP 55 IC 411 two-speed motors

MomentPower of inertia

Output Motor type Product code Speed Efficiency factor J=1/4 GD2 WeightkW M2AA 3GAA r/min % cos ϕ A I

NNm T

NT

Nkgm2 kg

3000/1500 r/min = 2/4 poles

0.37/0.07 71 B 078 202- 2810/1450 64/43 0.90/0.62 1.0/0.4 3.5/2.9 1.2/0.46 1.0/1.1 1.7/2.2 0.0005 6.50.65/0.10 80 A 088 201- 2860/1460 68/40 0.86/0.62 1.6/0.6 4.1/2.8 2.1/0.65 1.2/1.1 2.0/2.2 0.0009 90.9/0.15 80 B 088 202- 2870/1460 73/45 0.87/0.66 2.1/0.75 4.8/2.8 3.0/1.0 1.5/1.0 2.2/2.3 0.0011 10

1.4/0.22 90 S 098 201- 2870/1470 77/48 0.89/0.63 3.0/1.1 5.3/3.3 4.6/1.4 1.7/1.0 2.4/2.7 0.0019 131.9/0.3 90 L 098 202- 2880/1470 78/58 0.89/0.68 4.0/1.1 5.8/3.7 6.3/1.9 1.9/1.0 2.5/2.3 0.0024 162.5/0.4 100 L 108 201- 2900/1470 80/60 0.87/0.67 5.2/1.5 6.5/4.1 8.2/2.6 2.1/1.0 3.0/2.7 0.0041 21

3.5/0.6 112 M 118 204- 2895/1470 83.0/68.0 0.92/0.60 6.6/2.1 7.0/5.8 11.5/3.9 1.7/1.8 2.3/2.8 0.012 325.5/1.0 132 S 138 207- 2900/1470 84.0/64.0 0.88/0.65 10.8/3.5 7.8/5.7 18.1/6.5 2.4/2.0 2.9/2.8 0.016 427.4/1.2 132 M 138 208- 2875/1475 85.0/67.0 0.93/0.64 13.5/4.1 7.5/5.9 24.6/7.8 2.1/2.0 2.6/2.8 0.022 56

13/1.9 160 M 168 202- 2940/1470 88.5/79.5 0.92/0.79 23.0/4.4 7.8/6.4 42/12 2.1/2.1 3.0/2.5 0.054 9217.5/2.5 160 L 168 203- 2925/1475 89.0/81.0 0.92/0.77 31.0/5.8 7.1/6.7 57/16 2.0/2.5 2.6/2.9 0.057 99

20/2.8 180 M 188 207- 2930/1465 89.0/77.0 0.90/0.77 36.0/6.9 6.4/5.8 65/18 2.1/1.9 2.4/2.0 0.094 13225/3.6 180 L 188 208- 2940/1465 90.0/78.0 0.88/0.78 46.0/8.6 7.5/7.3 81/24 2.6/1.9 2.9/1.9 0.108 152

30/4.1 200 MLA 208 210- 2945/1480 91.5/85.0 0.89/0.72 54/10 8.0/7.1 97/26 2.2/2.7 2.8/2.8 0.15 17538/5.5 200 MLB 208 211- 2945/1480 92.5/86.5 0.91/0.74 67/13 7.7/6.8 123/35 2.2/2.6 2.6/2.6 0.19 205

43/6 225 SMB 228 207- 2950/1475 92.5/86.5 0.90/0.78 75/13 7.1/5.8 139/39 2.3/2.7 2.4/2.0 0.26 23550/7 225 SMC 228 208- 2955/1480 93.0/87.5 0.91/0.78 86/15 7.3/6.1 162/45 2.4/2.9 2.4/2.1 0.29 26070/10 250 SMB 258 204- 2965/1485 94.0/89.5 0.90/0.76 119/22 9.3/7.1 225/64 2.3/2.5 3.1/2.3 0.57 330

3000/1500 r/min = 2/4 poles

0.55/0.11 71 B 078 102- 2800/1440 68/50 0.85/0.62 1.4/0.5 4.0/3.0 1.8/0.73 1.5/1.4 2.0/2.4 0.0005 6.50.65/0.13 71 C 078 103- 2800/1440 70/55 0.87/0.62 1.6/0.55 4.1/3.0 2.2/0.86 1.6/1.4 2.1/2.4 0.0006 7.5

0.75/0.15 80 A 088 101- 2850/1460 73/57 0.80/0.57 1.9/0.67 4.5/3.5 2.5/0.98 1.8/1.4 2.4/2.4 0.0009 91.1/0.23 80 B 088 102- 2860/1460 76/63 0.83/0.60 2.6/0.88 5.0/3.7 3.8/1.5 1.8/1.3 2.4/2.4 0.0011 101.4/0.3 80 C 088 103- 2840/1450 75/67 0.86/0.64 3.1/1.0 5.0/3.7 4.7/2.0 1.8/1.2 2.4/2.5 0.0013 11

1.5/0.33 90 S 098 101- 2860/1460 77/66 0.87/0.67 3.3/1.1 5.2/3.9 5.0/2.1 1.8/1.1 2.4/2.4 0.0019 132.2/0.45 90 L 098 102- 2860/1460 80/73 0.88/0.65 4.6/1.4 5.9/4.4 7.3/2.9 2.1/1.2 2.6/2.6 0.0024 162.5/0.47 90 LB 098 103- 2860/1460 78/75 0.88/0.62 5.2/1.5 6.1/4.5 8.3/3.1 2.2/1.4 2.7/2.8 0.0027 18

3.0/0.6 100 L 108 101- 2880/1470 81/74 0.89/0.61 6.2/1.9 6.3/4.8 9.9/3.9 2.2/1.4 2.8/2.8 0.0041 213.5/0.7 100 LB 108 102- 2880/1470 80/77 0.91/0.65 7.0/2.0 6.2/4.8 12/4.6 2.1/1.2 2.8/3.0 0.005 25

4.5/1 112 M 118 104- 2875/1450 83.0/80.0 0.93/0.76 8.4/2.4 7.0/6.0 14.9/6.6 1.8/1.9 2.3/2.8 0.012 326.2/1.3 132 S 138 127- 2880/1455 84.0/80.0 0.91/0.67 11.8/3.5 7.0/6.5 20.6/8.5 2.0/2.6 2.6/3.3 0.016 428.3/1.7 132 M 138 108- 2875/1455 84.0/82.0 0.93/0.71 15.4/4.2 7.4/6.6 27.6/11.2 2.5/2.7 2.7/3.3 0.022 56

10/2 160 MA 168 101- 2910/1465 85.0/83.5 0.89/0.73 19.0/4.8 5.9/6.1 30/43 1.5/2.4 2.3/2.8 0.039 7316/3.2 160 M 168 102- 2915/1465 87.5/86.5 0.92/0.76 28.5/7.0 6.6/6.3 52/21 1.8/2.5 2.4/2.8 0.054 9219.5/4.5 160 L 168 103- 2930/1465 89.0/88.0 0.89/0.77 36/9.7 7.6/6.4 64/29 2.3/2.5 2.9/2.8 0.057 99

21.5/4.7 180 M 188 105- 2935/1465 90.0/88.0 0.91/0.77 38/10 7.0/5.3 70/28 2.1/2.1 2.6/2.3 0.094 13226/5.2 180 L 188 106- 2940/1470 90.5/89.5 0.89/0.75 47/11 6.9/5.8 85/34 2.3/2.4 2.6/2.4 0.108 152

32/8 200 MLA 208 110- 2940/1465 90.0/89.0 0.89/0.85 58/16 7.1/6.2 104/52 2.0/2.0 2.5/2.2 0.28 18039/10 200 MLB 208 111- 2950/1475 91.5/91.0 0.89/0.85 69/19 7.4/6.2 126/65 2.0/2.0 2.6/2.3 0.34 20542/11 200 MLC 208 112- 2950/1470 92.5/91.0 0.89/0.77 75/23 7.7/5.6 136/71 2.2/2.1 3.0/2.5 0.19 205

45/13 225 SMB 228 107- 2955/1475 93.0/91.5 0.92/0.82 76/25 7.4/5.3 145/84 2.0/2.0 2.6/2.1 0.27 23555/15 225 SMC 228 108- 2955/1475 93.5/92.5 0.91/0.82 94/29 7.3/5.4 178/97 2.0/2.0 2.6/2.2 0.30 26075/25 250 SMB 258 104- 2965/1475 94.5/93.0 0.92/0.82 125/48 8.9/5.5 241/162 2.3/2.0 3.1/2.2 0.36 330

Fan drive, two separate windings

Fan drive, Dahlander-connection

IN TNTS Tmax

Current Torque

1) Restamping from code H. Note that this results in a certain reduction of output. Rated output on request.

1) Sizes 63 to 100 voltage code H.Sizes 112 to 250 voltage code D.

400 V 50 Hz1)

The bullet indicates a 3-letter product code supplement for choice of mountingarrangement (page 11, pos. 12), voltage and frequency (below) and generation code (page11, pos. 14).

Code letter s for supplementing the pr oduct codeCode letter for voltage and frequency

Motor size A S B D H E X

63-100 - 220-230 V - 380-400 V1) 400-415 V 500 V112-132 - 220-230 V - 380-400 V 400-415 V 500 V160-250 220 V 230 V 380 V 400 V 415 V 500 V

Other rated voltage orfrequency, 690 V maximum

23ABB Motors

Insulation class FTemperature rise class F

1) Code S. 2) Restamping of code H. Note that this results in a certain reduction of output. Rated output on request.

IN I

ST

NT

max

Current Torque

TS

Fan drive, two separate windings

400 V 50 Hz1)


Motor sizes 63-100 Motor sizes 112-250Rated voltage at 50 Hz Rated voltage at 50 Hzand motor wound for Recalculation factor and motor wound for Recalculation factor

220 V 1) 220 V 1.82230 V 1.74 230 V 1.74380 V 2) 380 V 1.05

415 V 0.96500 V 0.80 500 V 0.80660 V 0.61 660 V 0.61690 V 0.58 690 V 0.58




NNm T

NT

Nkgm2 kg

1500/1000 r/min = 4/6 poles

0.30/0.10 71 B 078 205- 1400/950 64/41 0.78/0.66 0.9/0.56 3.3/2.3 2.0/1.1 1.5/1.4 2.0/2.1 0.0009 6.50.45/0.15 80 A 088 204- 1400/960 66/46 0.78/0.65 1.3/0.73 3.7/2.6 3.0/1.5 1.7/1.3 2.1/2.2 0.0017 8.50.65/0.22 80 B 088 205- 1400/960 70/53 0.82/0.64 1.7/0.94 3.9/2.9 4.4/2.2 1.7/1.4 2.1/2.2 0.0021 9.5

1.0/0.3 90 S 098 204- 1400/940 73/53 0.83/0.75 2.5/1.2 4.2/2.6 6.8/3.0 1.8/1.0 2.2/1.7 0.0032 131.5/0.45 90 L 098 205- 1400/940 75/58 0.84/0.73 3.5/1.6 4.3/2.9 10.0/4.5 1.7/1.0 2.1/1.8 0.0043 16

2.0/0.6 100 LA 108 203- 1430/960 77/62 0.85/0.72 4.5/2.0 5.0/3.3 13.0/5.9 1.8/1.0 2.4/1.9 0.0069 202.5/0.8 100 LB 108 204- 1430/960 79/68 0.84/0.71 5.5/2.5 5.6/3.5 16.0/7.9 2.0/1.1 2.5/2.0 0.0082 23

3.0/1.0 112 M 118 205- 1445/975 82.0/67.0 0.84/0.68 6.3/3.1 6.0/4.0 19.8/9.8 1.3/1.0 2.3/2.2 0.018 334.5/1.5 132 S 138 229- 1460/985 83.0/67.0 0.85/0.64 9.2/5.1 6.5/4.2 29.4/14.5 1.5/1.0 2.3/2.2 0.038 486.0/2.0 132 M 138 230- 1460/980 84.0/71.0 0.86/0.73 12.0/5.6 7.1/4.5 39.2/19.5 1.8/1.3 2.5/2.0 0.048 59

10.5/3.5 160 M 168 204- 1460/965 87.0/75.5 0.84/0.78 21/8.6 6.4/4.1 69/35 2.0/1.3 2.5/1.7 0.089 9314.5/4.5 160 L 168 205- 1460/970 88.5/77.0 0.85/0.76 28/11.0 6.9/4.6 95/44 2.2/1.5 2.6/1.9 0.119 117

16/5 180 M 188 209- 1470/980 89.0/78.0 0.83/0.73 31/12.5 6.3/4.6 104/49 1.9/1.5 2.5/2.0 0.176 13120/6.5 180 L 188 210- 1470/980 90.0/79.5 0.83/0.74 39/16.0 7.2/5.0 130/63 2.4/1.8 2.7/2.0 0.224 159

23/7.2 200 MLA 208 213- 1475/985 89.5/84.0 0.88/0.87 43/15 7.7/7.8 149/70 1.6/1.9 2.8/2.9 0.44 17530/9 200 MLB 208 214- 1470/985 90.0/83.5 0.90/0.89 54/18 7.7/7.9 195/87 1.6/1.7 2.7/2.5 0.53 200

34/11 225 SMB 228 209- 1470/985 91.0/85.0 0.91/0.89 60/21 7.7/6.7 221/107 1.5/1.3 2.7/2.3 0.67 22542/14 225 SMC 228 210- 1475/985 91.5/89.0 0.89/0.89 75/27 8.4/6.8 272/136 1.7/1.4 3.0/2.3 0.78 25563/18.5 250 SMB 258 205- 1475/985 93.5/87.0 0.89/0.79 110/40 7.5/7.3 408/179 2.4/3.0 2.7/2.6 0.89 335

24 ABB Motors

IN TN


400 V 50 Hz1)

IS

TS

Tmax

Total ly enclosed squirrel cage three phase motors , aluminium frame IP 55, IC 411, two-speed motors

CurrentMoment

Power of inertiaOutput Motor type Product code Speed Efficiency factor J=1/4 GD2 WeightkW M2AA 3GAA r/min % cos ϕ A I

NNm T

NT

Nkgm2 kg

1500/750 r/min = 4/8-poles Fan drive, two separate windings

Code letters for supplementing the product code

Code letters for voltage and frequencyMotor size A S B D H E X

63-100 - 220-230 V - 380-400 V1) 400-415 V 500 V112-132 - 220-230 V - 380-400 V 400-415 V 500 V

160-250 220 V 230 V 380 V 400 V 415 V 500 V

Other rated voltage orfrequency,690 V maximum

The bullets indicates a 3-letter product code supplement for choise of mounting arrangement(page 11, pos. 12), voltage and frequency (below) and generation code (page 11, pos. 4).

0.45/0.07 80 A 088 207- 1380/710 66/34 0.83/0.65 1.3/0.47 3.3/2.0 3.0/0.94 1.3/1.2 1.8/1.8 0.0017 8.50.65/0.09 80 B 088 208- 1380/710 69/34 0.84/0.67 1.7/0.56 3.6/2.0 4.4/1.2 1.6/1.0 1.9/1.8 0.0021 9.5

1.0/0.13 90 S 098 207- 1400/700 71/38 0.83/0.70 2.6/0.72 3.9/2.1 6.8/1.8 1.5/1.0 2.0/1.8 0.0032 131.4/0.18 90 L 098 208- 1420/710 74/41 0.81/0.62 3.5/1.0 4.5/2.3 9.4/2.4 1.7/1.1 2.3/2.1 0.0043 16

1.85/0.25 100 LA 108 206- 1430/720 78/45 0.84/0.60 4.2/1.4 4.9/2.5 12.0/3.3 1.7/1.1 2.3/2.2 0.0069 202.3/0.33 100 LB 108 207- 1430/720 80/49 0.86/0.60 5.0/1.6 5.2/2.6 15.0/4.3 1.8/1.1 2.4/2.2 0.0082 23

3.0/0.4 112 M 118 206- 1440/730 81.0/51.0 0.87/0.58 6.2/2.0 6.8/3.8 19.9/5.2 1.5/1.6 2.4/2.6 0.018 324.0/0.6 132 S 138 231- 1465/740 84.0/51.0 0.84/0.53 8.2/3.2 6.5/3.5 26.1/7.7 1.5/1.1 2.4/2.5 0.038 485.5/0.9 132 M 138 232- 1455/735 84.0/53.0 0.87/0.64 10.9/3.9 6.2/3.1 36.1/11.7 1.5/1.1 2.2/2.0 0.048 59

9/1.3 160 M 168 206- 1460/735 87.0/60.0 0.84/0.53 18/5.9 6.6/4.0 59/17 2.0/2.2 2.5/2.7 0.089 9413.5/2.0 160 L 168 207- 1455/735 88.0/64.0 0.86/0.54 26/8.4 6.0/4.1 89/26 1.9/2.2 2.3/2.6 0.119 117

16/2.3 180 M 188 211- 1475/740 88.5/64.0 0.82/0.53 32/9.7 6.8/4.1 104/30 2.2/2.2 2.7/2.6 0.176 13719/2.7 180 L 188 212- 1475/740 89.5/68.0 0.,83/0.54 37/10.5 7.5/7.2 123/35 2.6/2.6 2.9/2.6 0.224 161

26/3.3 200 MLA 208 216- 1475/740 91.0/73.0 0.85/0.59 49.0/11.0 6.9/4.6 168/46 2.1/2.2 2.5/2.3 0.28 18030/3.8 200 MLB 208 217- 1470/740 91.5/75.5 0.86/0.59 55.0/12.5 6.7/4.6 195/49 2.1/2.2 2.4/2.2 0.34 205

38/5.2 225 SMB 228 211- 1480/740 91.5/80.5 0.84/0.63 72/15 7.3/5.2 245/67 2.1/2.3 2.6/2.3 0.41 23046/7 225 SMC 228 212- 1480/740 92.5/82.0 0.86/0.66 85/19 7.7/4.9 297/90 2.3/2.1 2.7/2.1 0.49 26563/10 250 SMB 258 206- 1475/740 93.5/83.0 0.89/0.65 110/27 7.5/6.0 408/129 2.4/3.0 2.7/2.7 0.89 335

1500/750 r/min = 4/8-poles Fan drive , Dahlander-connection

0.37/0.09 71 B 078 104- 1390/680 65/42 0.73/0.63 1.2/0.49 3.3/2.0 2.5/1.2 1.8/1.4 1.8/1.8 0.009 6.50.45/0.1 71 C 078 105- 1390/690 64/62 0.73/0.59 1.4/0.57 3.4/2.1 3.1/1.4 1.9/1.6 2.3/2.1 0.0012 7.50.55/0.11 80 A 088 104- 1380/700 67/48 0.80/0.61 1.6/0.54 3.1/2.3 3.8/1.5 1.5/1.4 1.8/1.8 0.0017 8.5

0.75/0.16 80 B 088 105- 1390/700 71/51 0.80/0.62 2.0/0.70 3.4/2.4 5.1/1.2 1.5/1.2 1.9/1.9 0.0021 9.50.9/0.2 80 C 088 106- 1390/700 70/57 0.80/0.62 2.4/0.83 3.6/2.4 6.2/2.8 1.7/1.3 2.1/1.9 0.0024 11

1.1/0.26 90 S 098 104- 1410/700 73/53 0.80/0.63 2.8/1.2 4.2/2.4 7.4/3.6 1.8/1.2 2.3/1.9 0.0032 131.5/0.31 90 L 098 105- 1420/710 77/57 0.78/0.54 3.7/1.5 4.8/2.8 10/4.2 2.2/1.7 2.7/2.5 0.0043 161.8/0.35 90 LB 098 106- 1410/710 76/60 0.83/0.56 4.2/1.5 4.3/2.7 12/4.8 1.9/1.6 2.3/2.3 0.0048 18

2.2/0.48 100 LA 108 103- 1430/720 79/65 0.82/0.59 5.1/1.8 5.1/3.0 14/6.4 1.9/1.2 2.5/2.1 0.0069 202.8/0.6 100 LB 108 104- 1430/720 81/68 0.82/0.58 6.4/2.2 5.2/3.0 18/8.0 2.0/1.2 2.6/2.2 0.0082 233.0/0.65 100 LC 108 105- 1430/720 81/67 0.81/0.56 6.8/2.5 5.6/3.0 20/8.7 2.2/1.3 2.8/2.3 0.009 26

3.5/0.7 112 M 118 126- 1430/720 81.0/71.0 0.89/0.58 7.0/2.5 6.8/4.4 23.4/9.3 1.6/1.7 2.5/2.7 0.018 325.0/1.0 132 S 138 131- 1450/725 83.0/74.0 0.87/0.59 9.9/3.3 6.4/3.6 32.9/13.2 1.5/1.0 2.3/2.0 0.038 486.8/1.4 132 M 138 132- 1460/730 85.0/73.0 0.84/0.55 13.7/5.1 7.6/3.6 44.5/18.3 2.0/1.4 2.8/2.7 0.048 59

10.5/2.2 160M 168 104- 1460/735 87.5/79.0 0.84/0.54 21/7.4 6.9/3.7 69/29 2.2/1.5 2.7/2.3 0.089 9215.5/2.7 160 L 168 105- 1460/735 88.5/79.5 0.85/0.51 30/9.5 6.9/3.9 101/35 2.2/1.7 2.6/2.6 0.119 117

17/3.4 180 M 188 107- 1470/730 88.5/78.0 0.85/0.56 33/11 5.8/4.3 111/44 1.7/1.2 2.3/1.9 0.176 13022/4.4 180 L 188 108- 1475/735 89.5/79.0 0.83/0.53 43/15 6.7/3.9 143/57 2.0/1.7 2.6/2.3 0.224 159

29/6.5 200 MLA 208 116- 1470/730 90.5/86.0 0.86/0.64 54/17 6.9/4.2 188/81 2.2/1.9 2.4/1.9 0.28 18033/8 200 MLB 208 117- 1475/730 91.5/86.5 0.86/0.64 61/21 7.8/4.2 214/105 2.6/1.9 2.6/1.8 0.34 205

42/10 225 SMB 228 111- 1480/740 92.0/89.5 0.78/0.61 85/27 7.8/5.0 271/129 2.5/2.2 3.0/2.3 0.49 26550/11 225 SMC 228 112- 1465/735 92.5/89.5 0.87/0.65 91/28 7.3/4.7 324/143 2.3/2.0 2.5/2.0 0.49 26560/15 250 SMB 258 106- 1475/735 93.0/90.0 0.86/0.70 104/34 7.9/4.7 388/195 2.6/2.1 2.7/2.0 0.89 335

1) Sizes 63 -100 voltage code H.Sizes 112 - 250 voltage code D.

Torque

25ABB Motors

Insulation class FTemperature rise class F

In TN

IS TS

Tmax

400 V 50 Hz1)



220 V 1) 220 V 1.82230 V 1.74 230 V 1.74380 V 2) 380 V 1.05500 V 0.80 500 V 0.80660 V 0.61 660 V 0.61690 V 0.58 690 V 0.58

MomentPower- of inertia


NNm T

NT

Nkgm2 kg

1000/750 r/min = 6/8-poles Fan drive, two separate windings

0.25/0.10 80 A 088 210- 930/700 52/39 0.74/0.67 0.95/0.56 2.6/2.0 2.6/1.3 1.2/1.1 1.8/1.8 0.0017 8.50.33/0.14 80 B 088 211- 940/700 57/44 0.71/0.67 1.2/0.70 3.0/2.1 3.3/1.9 1.4/1.1 2.0/1.7 0.0021 9.5

0.45/0.2 90 S 098 210- 940/700 59/44 0.72/0.67 1.6/1.0 3.1/2.2 4.6/2.7 1.4/1.0 2.0/1.7 0.0032 130.7/0.3 90 L 098 211- 930/700 63/49 0.75/0.64 2.2/1.5 3.1/2.3 7.2/4.1 1.3/1.1 1.8/1.8 0.0043 16

0.9/0.37 100 LA 108 209- 940/710 69/55 0.79/0.63 2.4/1.55 3.3/2.7 9.2/5.0 1.2/1.1 1.8/1.8 0.0069 201.2/0.5 100 LB 108 210- 940/710 73/58 0.75/0.67 3.2/1.9 3.4/2.6 12.0/6.7 1.2/1.1 1.9/1.9 0.0082 23

1.6/0.8 112 M 118 207- 965/720 73.0/57.0 0.70/0.66 4.5/3.1 5.8/4.0 15.8/10.6 2.0/1.6 2.6/2.2 0.018 332.6/1.3 132 S 138 213- 975/730 77.0/64.0 0.72/0.64 6.8/4.6 6.5/4.3 25.5/17.0 1.6/1.4 2.8/2.5 0.031 483.5/1.6 132 M 138 214- 975/730 79.0/66.0 0.72/0.66 8.9/5.2 7.0/4.9 34.3/20.9 1.8/1.5 3.0/2.5 0.049 59

160 M On request160 L On request

180 M On request180 L On request

17/7.5 200 MLB 208 221- 985/740 88.0/81.5 0.85/0.77 33/17 7.1/6.4 165/97 2.2/2.2 2.5/2.5 0.42 18520/9 200 MLC 208 222- 985/740 88.5/82.5 0.84/0.74 39/21 7.6/7.0 194/116 2.4/2.6 2.7/2.9 0.48 200

26/12 225 SMB 228 215- 985/740 89.5/84.5 0.85/0.76 49/27 7.4/7.1 252/155 2.2/2.4 2.5/2.7 0.63 22532/14 225 SMC 228 216- 985/740 90.5/85.5 0.83/0.76 62/31 7.0/7.2 310/180 2.4/2.5 2.4/2.5 0.74 25043/15 250 SMB 258 208- 990/745 91.0/86.0 0.84/0.75 81/34 7.3/7.4 415/198 2.2/2.7 2.5/2.8 1.41 320

1000/500 r/min = 6/12-poles0.28/0.05 80 A 088 107- 920/440 54/31 0.72/0.60 1.1/0.40 2.6/1.7 2.9/1.1 1.3/1.4 1.8/1.8 0.0017 8.50.42/0.07 80 B 088 108- 920/440 57/34 0.74/0.57 1.5/0.54 2.7/1.7 4.4/1.5 1.2/1.5 1.7/1.9 0.00212 9.5

0.5/0.08 90 S 098 107- 920/440 60/31 0.74/0.59 1.7/0.63 2.9/1.7 5.2/1.7 1.2/1.5 1.8/2.0 0.0032 130.75/0.12 90 L 098 108- 930/450 64/36 0.73/0.54 2.4/0.90 3.0/1.8 7.7/2.5 1.3/1.6 1.9/2.1 0.0043 16

0.9/0.16 100 LA 108 106- 940/470 69/50 0.73/0.49 2.6/0.96 3.6/2.1 9.0/3.2 1.3/1.2 2.0/2.1 0.0069 201.3/0.2 100 LB 108 107- 940/470 71/52 0.76/0.47 3.5/1.2 3.4/2.2 13.0/4.0 1.2/1.2 1.8/2.2 0.0082 23

Fan drive, Dahlander-connection

1) Sizes 63 -100 voltage code H.Sizes 112 - 250 voltage code D.

Current Torque

1) Code S. 2) Restamping from code H. Note that this results in a certain reduction of output. Rated output on request.

26 ABB Motors




NNm T

NT

Nkgm2 kg

3000/1500 r/min = 2/4 poles Highest output at both speeds, two separate windings

0.45/0.22 80 A 088 213- 2890/1440 65/55 0.82/0.62 1.25/0.95 3.8/3.0 1.5/1.5 1.1/1.4 2.1/2.4 0.0009 90.65/0.33 80 B 088 214- 2880/1440 69/61 0.88/0.68 1.6/1.2 4.2/3.4 2.2/2.2 1.2/1.2 2.1/2.1 0.0011 10

1.1/0.55 90 S 098 213- 2900/1450 74/62 0.87/0.64 2.5/2.0 5.1/3.6 3.6/3.6 1.4/1.5 2.3/2.5 0.0019 131.5/0.75 90 L 098 214- 2900/1450 77/70 0.87/0.67 3.3/2.4 5.7/4.1 4.9/4.9 1.5/1.5 2.5/2.5 0.0024 162.0/1.0 100 L 108 212- 2890/1450 76/68 0.91/0.75 4.2/2.9 5.8/3.7 6.6/6.6 1.7/1.1 2.5/2.0 0.0041 21

2.6/1.3 112 M 118 201- 2900/1460 80.0/75.0 0.92/0.72 5.1/3.5 6.4/5.0 8.6/8.5 1.6/1.6 2.3/2.3 0.012 324.4/2.2 132 SB 138 201- 2925/1450 81.0/74.0 0.86/0.73 9.1/5.9 7.3/4.4 14.4/14.5 2.0/1.3 2.3/2.2 0.016 425.6/2.8 132 M 138 202- 2885/1440 82.0/77.0 0.93/0.75 10.6/7.0 6.7/5.0 18.5/18.6 1.8/1.4 2.1/2.2 0.022 56

12/6 160 M 168 209- 2835/1460 87.5/84.5 0.92/0.80 22/13.0 7.7/6.0 39/39 2.1/2.3 2.8/2.4 0.054 9215/7.5 160 L 168 210- 2940/1460 88.5/84.5 0.93/0.78 27/16.5 7.9/6.0 49/49 2.2/2.4 2.9/2.4 0.057 9918/9 180 L 188 202- 2945/1460 89.0/84.0 0.90/0.77 32/20 7.7/5.2 58/59 2.5/2.3 2.8/2.1 0.108 152

23/12 200 MLA 208 201- 2960/1475 90.0/89.0 0.89/0.85 42/23 7.8/7.4 74/77 1.7/2.2 2.8/2.5 0.28 17830/16 200 MLB 208 202- 2960/1475 91.0/90.0 0.90/0.87 53/30 8.2/7.3 97/104 1.8/2.2 2.9/2.5 0.34 204

36/18 225 SMB 228 201- 2960/1480 91.5/91.5 0.91/0.76 63/38 8.0/7.2 116/116 2.5/3.8 2.7/2.5 0.26 23640/20 225 SMC 228 202- 2960/1475 92.0/91.5 0.91/0.79 69/41 8.5/6.5 129/129 2.8/3.3 2.8/2.2 0.29 26150/25 250 SMB 258 201- 2965/1485 93.0/93.0 0.91/0.76 86/52 8.9/8.5 161/161 2.1/3.5 2.9/2.9 0.57 333

3000/1500 r/min = 2/4 poles Highest output at both speeds, Dahlander-connection

0.45/0.3 71 B 078 111- 2700/1390 60/61 0.87/0.77 1.3/1.0 3.0/3.2 1.6/2.0 1.6/1.6 1.8/2.0 0.0009 6.50.6/0.45 80 A 088 110- 2770/1400 63/66 0.83/0.80 1.7/1.3 3.4/3.4 2.0/3.0 1.6/1.4 2.0/1.9 0.0017 90.85/0.65 80 B 088 111- 2770/1400 68/68 0.86/0.84 2.1/1.7 3.8/3.5 2.9/4.4 1.7/1.4 2.1/1.8 0.0021 10

1.3/1.0 90 S 098 110- 2730/1400 71/71 0.88/0.80 3.1/2.6 3.9/3.8 4.5/6.8 2.0/1.5 2.2/2.0 0.0032 131.9/1.5 90 L 098 111- 2820/1420 76/75 0.82/0.76 4.4/3.9 5.1/4.4 6.4/10 2.8/2.0 3.0/2.5 0.0043 16

2.5/2.1 100 LA 108 109- 2800/1430 68/76 0.89/0.81 6.0/5.0 4.8/4.4 8.5/14 2.4/1.6 2.7/2.2 0.0069 203.1/2.5 100 LB 108 110- 2820/1440 72/79 0.90/0.80 7.0/5.7 5.5/5.1 10/16 2.6/1.8 2.9/2.5 0.0082 23

4/2.6 112 M 118 101- 2865/1430 82.0/77.0 0.94/0.76 7.6/6.5 6.3/6.2 13.3/17.4 1.8/2.3 2.1/2.6 0.012 324.7/3.1 132 SB 138 101- 2820/1420 79.0/77.0 0.93/0.76 9.2/7.7 5.5/5.7 15.9/20.8 1.8/2.2 2.1/2.4 0.016 427.2/4.8 132 M 138 102- 2870/1435 84.0/81.0 0.93/0.76 13.3/11.5 7.1/6.2 24.0/31.9 2.4/2.5 2.6/2.7 0.022 56

9/6.5 160 MA 168 106- 2885/1440 83.0/82.0 0.92/0.74 17.1/15.6 4.6/4.3 40/43 1.3/1.7 1.9/1.9 0.039 7312.5/9 160 M 168 107- 2890/1440 85.5/85.5 0.93/0.80 22.5/19 5.2/4.6 41/60 1.4/1.8 1.9/1.9 0.054 9215/10.5 160 L 168 108- 2900/1445 87.0/86.0 0.93/0.77 27/23 5.8/4.9 49/69 1.6/2.1 2.1/2.1 0.057 99

18/12 180 M 188 101- 2940/1455 89.0/89.0 0.88/0.79 33/25 6.8/5.3 59/79 2.1/2.4 2.6/2.2 0.094 13224/17 180 L 188 102- 2945/1455 90.0/90.0 0.89/0.80 43/34 7.4/5.2 78/111 2.4/2.4 2.8/2.1 0.108 152

32/24 200 MLA 208 101- 2940/1470 89.0/90.5 0.89/0.86 58/45 6.8/5.9 104/156 1.8/2.1 2.4/2.1 0.28 18039/29 200 MLB 208 102- 2950/1470 90.5/91.0 0.84/0.86 75/53 6.8/7.0 126/188 1.7/2.2 2.6/2.4 0.34 205

42/32 225 SMB 228 101- 2955/1475 92.5/93.0 0.92/0.88 71/57 7.1/6.5 136/207 1.5/1.9 2.5/2.3 0.49 23050/40 225 SMC 228 102- 2960/1475 92.5/93.0 0.84/0.87 94/71 7.4/7.1 161/259 1.8/2.0 2.8/2.5 0.49 26568/50 250 SMB 258 101- 2940/1475 93.0/93.5 0.93/0.88 113/87 6.6/6.9 220/324 1.5/2.1 2.4/2.5 0.89 335

400 V 50 Hz1)

Current

IN IS

TNT

S Tmax

Torque






63-100 - 220-230 V - 380-400 V1) 400-415 V 500 V112-132 - 220-230 V - 380-400 V 400-415 V 500 V160-250 220 V 230 V 380 V 400 V 415 V 500 V


27ABB Motors



NNm T

NT

Nkgm2 kg

Current Torque

1500/1000 r/min = 4/6 poles

0.28/0.18 71 B 078 217- 1410/930 57/45 0.75/0.67 1.0/0.90 3.0/2.2 1.8/1.8 1.5/1.3 2.0/1.9 0.0009 6.50.35/0.30 80 A 088 216- 1430/930 59/52 0.65/0.69 1.4/1.2 3.5/2.4 2.3/3.0 1.8/1.3 2.4/1.9 0.0017 8.50.5/0.37 80 B 088 217- 1430/940 64/59 0.71/0.67 1.6/1.4 3.7/2.8 3.3/3.7 1.8/1.4 2.4/2.0 0.0021 9.5

0.8/0.5 90 S 098 216- 1430/940 68/57 0.80/0.66 2.2/2.0 3.9/2.8 5.3/5.0 1.5/1.4 2.1/2.1 0.0032 131.2/0.75 90 L 098 217- 1430/940 73/63 0.81/0.67 3.0/2.6 4.4/3.1 8.0/7.6 1.7/1.5 2.3/2.1 0.0043 16

1.5/0.9 100 LA 108 214- 1440/960 75/69 0.84/0.65 3.5/3.0 4.7/3.8 9.9/8.9 1.5/1.5 2.2/2.4 0.0069 201.8/1.1 100 LB 108 215- 1460/960 77/70 0.78/0.64 4.4/3.6 5.8/3.9 11/11 2.1/1.6 3.0/2.5 0.0082 23

2.6/1.7 112 M 118 202- 1445/960 80.0/73.0 0.86/0.76 5.5/4.4 5.9/5.2 17.2/16.9 1.5/1.5 2.2/2.4 0.018 333.3/2.2 132 S 138 223- 1470/980 82.0/76.0 0.82/0.65 7.1/6.4 6.8/4.6 21.4/21.4 1.4/1.2 2.5/2.4 0.038 484.5/3 132 M 138 224- 1470/980 82.0/77.0 0.85/0.70 9.3/8.0 7.2/5.6 29.2/29.2 1.4/1.5 2.3/2.6 0.048 59

7.5/5.5 160 M 168 211- 1465/965 85.5/80.5 0.83/0.77 15.5/13.0 7.1/4.7 49/54 2.1/1.8 2.7/1.9 0.089 9311.5/8.5 160 L 168 212- 1465/965 86.5/82.5 0.84/0.76 23.0/19.5 7.0/4.9 75/84 2.1/1.8 2.8/2.0 0.119 117

13/8 180 M 188 203- 1475/975 88.0/82.5 0.82/0.75 26.0/19.0 6.5/4.3 84/78 1.9/1.4 2.6/1.8 0.176 13115/10 180 L 188 204- 1475/975 88.5/84.0 0.83/0.74 30.0/23.0 7.1/4.4 97/98 2.3/1.5 2.7/1.9 0.224 159

18/12 200 MLA 208 204- 1475/985 88.5/86.0 0.91/0.86 33/24 7.6/7.8 117/116 2.1/2.6 2.5/2.6 0.42 18522/14.7 200 MLB 208 205- 1480/985 89.5/86.5 0.89/0.87 40/29 8.2/7.6 142/143 2.4/2.6 2.8/2.5 0.48 20025/16.7 200 MLC 208 206- 1475/980 89.0/85.5 0.87/0.88 47/32 7.7/6.7 162/162 2.3/2.3 2.6/2.2 0.48 200

32/21 225 SMB 228 203- 1480/985 90.0/89.5 0.88/0.86 58/40 8.6/8.0 206/204 2.3/2.4 2.8/2.7 0.63 22536/24 225 SMC 228 204- 1480/985 90.5/90.0 0.88/0.87 66/45 8.4/7.4 232/233 2.2/2.2 2.8/2.5 0.74 25050/32 250 SMB 258 202- 1475/985 92.5/90.5 0.89/0.80 89/65 7.5/7.1 324/310 2.3/3.1 2.6/2.6 0.89 335

Highest output at both speeds, two separate windings

400 V 50 Hz1)

Insulation c lass FTemperature rise c lass F

INT

SIS

TN

Tmax

1) Code S. 2) Restamping of code H. Note that this results in a certain reduction of output. Rated output on request.



220 V 1) 220 V 1.82230 V 1.74 230 V 1.74380 V 2) 380 V 1.05

415 V 0.96500 V 0.80 500 V 0.80660 V 0.61 660 V 0.61690 V 0.58 690 V 0.58


28 ABB Motors




NNm T

NT

Nkgm2 kg


0.22/0.11 80 A 088 219- 1420/700 61/45 0.80/0.58 0.7/0.65 3.4/2.2 1.5/1.5 1.2/1.4 2.0/2.2 0.0017 8.50.33/0.16 80 B 088 220- 1420/690 63/49 0.83/0.60 0.95/0.80 3.2/2.3 2.2/2.2 1.2/1.3 1.9/2.0 0.0021 9.5

0.5/0.25 90 S 098 219- 1440/690 64/51 0.78/0.65 1.5/1.1 3.6/2.3 3.3/3.4 1.3/1.2 2.2/1.9 0.0032 130.7/0.33 90 L 098 220- 1440/690 69/57 0.80/0.61 1.9/1.4 4.2/2.4 4.6/4.6 1.3/1.2 2.2/1.9 0.0043 16

1.0/0.5 100 LA 108 217- 1440/700 71/61 0.86/0.63 2.4/1.95 4.2/2.5 6.6/6.8 1.2/1.1 2.0/1.9 0.0069 201.4/0.7 100 LB 108 218- 1440/700 73/62 0.87/0.62 3.2/2.7 4.3/2.6 9.3/9.5 1.2/1.1 2.0/1.9 0.0082 23

1.8/0.9 112 M 118 203- 1470/715 77.0/65.0 0.76/0.66 4.4/3.0 6.5/4.0 11.7/12.0 1.2/1.6 2.2/2.4 0.018 322.5/1.3 132 S 138 225- 1470/730 80.0/69.0 0.79/0.58 5.7/4.7 6.7/4.4 16.2/17.0 1.6/1.4 2.6/2.7 0.038 483.3/1.7 132 M 138 226- 1470/725 81.0/71.0 0.83/0.67 7.1/5.2 8.0/4.8 21.4/22.4 1.8/1.8 2.7/2.2 0.048 59

5.5/2.7 160 M 168 213- 1465/730 85.0/71.0 0.83/0.57 11.5/9.6 6.8/4.0 36/35 2.1/2.0 2.6/2.3 0.089 929/4.5 160 L 168 214- 1465/730 86.5/73.5 0.83/0.56 18/16 7.0/4.1 59/59 2.1/2.1 2.7/2.5 0.119 11714/7 180 L 188 206- 1475/735 88.0/76.0 0.83/0.56 28/24 7.7/4.2 91/91 2.6/2.3 2.9/2.3 0.225 159

18.5/9.4 200 MLA 208 207- 1475/730 89.5/82.5 0.85/0.65 35/26 7.3/4.3 120/123 2.2/1.9 2.5/1.8 0.28 18022/11 200 MLB 208 208- 1480/735 90.5/83.0 0.84/0.60 42/32 8.4/4.7 142/143 2.6/2.4 2.9/2.2 0.34 205

28/14 225 SMB 228 205- 1480/735 90.0/85.5 0.85/0.61 53/39 7.7/4.9 181/182 2.1/2.4 2.7/2.2 0.41 23034/17 225 SMC 228 206- 1480/735 92.0/87.0 0.86/0.66 63/43 7.9/4.8 219/221 2.2/2.2 2.7/2.0 0.49 26550/25 250 SMB 258 203- 1480/740 92.5/88.0 0.87/0.60 90/68 8.6/6.0 323/323 2.6/3.5 3.0/2.9 0.89 335

1500/750 r/min = 4/8 poles Highest output at both speeds, Dahlander-connection

0.22/0.12 71 B 078 114- 1410/680 61/36 0.73/0.62 0.75/0.80 3.4/1.8 1.4/1.6 1.6/1.5 1.9/1.9 0.0009 6.50.4/0.2 80 A 088 113- 1410/700 63/45 0.78/0.60 1.2/1.1 3.1/2.1 2.7/2.7 1.3/1.4 1.9/2.0 0.0017 8.50.6/0.28 80 B 088 114- 1410/700 67/50 0.78/0.56 1.7/1.5 3.5/2.2 4.0/3.8 1.5/1.7 2.0/2.2 0.0021 9.5

0.7/0.37 90 S 098 113- 1420/700 72/50 0.80/0.57 1.8/1.9 4.4/2.3 4.7/5.1 1.6/1.6 2.3/2.2 0.0032 131.1/0.55 90 L 098 114- 1420/700 73/55 0.84/0.58 2.6/2.6 4.1/2.3 7.4/7.5 1.4/1.5 2.0/2.1 0.0043 16

1.5/0.75 100 LA 108 112- 1440/710 76/62 0.85/0.57 3.4/3.2 4.6/2.8 10.0/10.0 1.4/1.5 2.2/2.2 0.0069 202.0/0.95 100 LB 108 113- 1440/710 78/64 0.86/0.55 4.4/4.0 4.8/2.9 13.0/12.0 1.4/1.6 2.2/2.3 0.0082 23

2.5/1.5 112 M 118 103- 1410/705 78.0/67.0 0.90/0.66 5.1/4.9 5.5/4.1 16.9/20.3 1.4/1.5 2.1/2.4 0.018 323.8/1.9 132 S 138 125- 1450/730 82.0/70.0 0.86/0.52 7.7/7.6 5.6/3.7 25.0/24.9 1.4/1.3 2.1/2.7 0.038 485/2.5 132 M 138 126- 1455/730 85.0/73.0 0.88/0.52 9.6/9.6 6.9/4.8 32.8/32.7 1.7/2.0 2.4/2.8 0.048 59

8/4.5 160 M 168 109- 1440/730 84.5/79.5 0.86/0.60 16/13.5 4.5/3.4 53/59 1.3/1.4 1.8/1.9 0.089 9212/7 160 L 168 110- 1445/730 86.5/81.0 0.87/0.59 23/21 5.0/3.5 79/92 1.5/1.4 1.9/1.9 0.119 11716/8 180 L 188 104- 1460/730 88.0/78.5 0.86/0.53 31/28 1.9/3.4 105/104 1.4/1.6 1.9/2.1 0.224 159

22/13 200 MLA 208 107- 1475/735 87.5/86.0 0.81/0.69 45/32 6.5/5.9 142/169 2.0/2.5 2.6/2.7 0.36 16525/15 200 MLB 208 108- 1475/735 89.0/86.0 0.86/0.67 47/38 7.6/6.0 162/195 2.2/2.6 2.7/2.7 0.42 18529/17 200 MLC 208 109- 1475/735 90.0/88.0 0.91/0.75 52/38 7.2/6.1 188/221 2.2/2.6 2.4/2.4 0.48 200

35/21 225 SMB 228 105- 1475/735 90.0/89.0 0.90/0.74 63/47 6.7/5.8 227/273 1.7/2.1 2.2/2.3 0.63 22542/25 225 SMC 228 106- 1475/735 91.0/89.5 0.91/0.75 74/54 6.8/5.9 272/325 1.8/2.1 2.2/2.2 0.74 25055/33 250 SMB 258 103- 1480/740 92.0/90.5 0.90/0.75 97/71 7.3/6.4 355/426 2.1/2.5 2.5/2.5 1.50 320


16/12 200 MLB 208 219- 985/740 86.5/82.5 0.85/0.73 31/29 7.0/6.3 155/155 2.1/2.4 2.4/2.6 0.42 18518/13.5 200 MLC 208 220- 985/740 87.5/83.5 0.83/0.72 36/32 7.9/6.6 174/174 2.5/2.6 2.8/2.8 0.48 200

23/17 225 SMB 228 213- 985/740 89.0/85.5 0.84/0.78 46/37 7.9/6.3 222/220 2.3/2.2 2.7/2.3 0.63 22528/20 225 SMC 228 214- 985/740 89.0/86.5 0.86/0.77 57/43 7.1/6.5 272/259 2.0/2.3 2.4/2.4 0.74 25037/27 250 SMB 258 207- 990/740 90.0/87.5 0.83/0.75 71/59 7.8/6.7 357/348 2.3/2.5 2.7/2.5 1.41 320

ISIN

TN TST

max

400 V 50 Hz1)

Current Torque

1) Sizes 63 to 100 voltage code H. Sizes 112 to 250 voltage code D.





63-100 - 220-230 V - 380-400 V1) 400-415 V 500 V112-132 - 220-230 V - 380-400 V 400-415 V 500 V160-250 220 V 230 V 380 V 400 V 415 V 500 V


Insulation c lass FTemperature rise c lass F

29ABB Motors

Motor s with other n umber of polesData on these , and on big ger frame siz e, on request. IP 55 IC 411

Single-speed motors

SpeedNo. of poles r/min Motor type M2AA

10 600 90-10012 500 80-10014 430 90-100

16 375 90-10018 330 90-100

Two-speed motors for fan drives

Type of SpeedNo. of poles winding r/min Motor type M2AA

4/6 PAM 1500/1000 71-1006/8 PAM 1000/750 71-100

6/12 Dahlander 1000/500 71-1008/16 Dahlander 750/375 90-100

2/6 2 windings 3000/1000 71-1004/12 2 windings 1500/500 80-1004/16 2 windings 1500/375 90-100

6/12 2 windings 1000/500 80-1008/12 2 windings 750/500 80-1008/16 2 windings 750/375 90-100

Two-speed motors with highest output at both speeds


4/6 PAM 1500/1000 71-1006/8 PAM 1000/750 71-100

6/12 Dahlander 1000/500 80-1002/6 2 windings 3000/1000 71-100

2/8 2 windings 3000/750 71-1002/12 2 windings 3000/500 80-100

2/16 2 windings 3000/375 90-1004/12 2 windings 1500/500 80-100

Three-speed motors for fan drives


2/4/6 Dahlander + 1 winding 3000/1500/1000 80-1002/4/8 Dahlander + 1 winding 3000/1500/750 80-100


Three-speed motors with highest output at all speeds



30 ABB Motors

Motor si zes 112 to 132

Rating plates

Motor sizes 63 to 100

Single-speed motors of size 160 to 250 are availablewith voltage codes S and D, i.e., voltage range at both50 and 60 Hz. The rating plate is arranged in the form ofa table, with values for current, power factor and motorspeed at six voltages.

Single-speed motors of size 63 to 132 are available withvoltage codes S and D, i.e., voltage range at both 50and 60 Hz. The current rating for each voltage range isspecified on the rating plate. It represents the highestcurrent that can exist within the voltage range at therated output. The power factor and speed specified onthe rating plate apply at 400 V 50 Hz and 460 V 60 Hz.

Motor sizes 160 to 250

31ABB Motors

Code Variant Motor type1) M2AA

63-100 112-132 160-180 200-250

Balancing052 Balancing to grade R (ISO 2373). T T T T417 Balancing to grade S (ISO 2373). – T T R424 Balancing with full key T T T T426 Balancing with half key S S S S

Bearings and lubrication036 Transport lock for bearings. – L L L037 Roller bearing at D-end – – L L

Transport lock included.039 Cold resistant grease. L L L L

For bearing temperatures -55 - +100 °C.040 Heat resistant grease. S L L L

For bearing temperatures -25 - +150 °C.Mandatory for ambient temperatures >50 °C.

041 Bearings regreasable via grease nipples. – L L S042 Internal bearing cover, locked D-end. L L S L

Standard for sizes 90 and 100Standard for sizes 112 and 132, flanged versions.

043 SPM nipples. – L L L057 2RS bearings at both ends. L L L L

Grease for bearing temperatures -30 - +110°C058 Angular contact ball bearing at D-end, R L L –

shaft force away from bearing.Transport lock included.

059 Angular contact ball bearing at N-end, R L L Lshaft force towards bearing.Transport lock included.

060 Angular contact ball bearing at D-end, R – – –shaft force towards bearing.

061 Angular contact ball bearing at N-end. – – – LShaft force away from bearing.Transport lock included.

188 Larger bearing than standard. – L L SLarger bearing at D-end, 63 series.Sizes 90 and 100 have 63 series bearings as standard.

Brake196 Built-on brake, standard motor. R2) L2) – –

Externally mounted brake with automatic adjustment of brake air gap.197 Built on brake, type BXLF, standard motor R2) L 2) – –

Branch standard designs071 Cooling Tower duty. T T T T

Only motors with shaft extensions downwards.079 Silumin-alloy rotor cage. T T T T142 ”Manilla" winding connection. (440 V∆ series, 220 V∆ parallel, 60Hz) T T T T

Single speed motors only.170 Smoke venting specification 200 °C, 2 h. T T T T171 Smoke venting specification 300 °C, 0.5 h. T T T T172 Smoke venting specification 300 °C, 1 h. R R R R178 Stainless steel/acid proof bolts. L L L L199 Extreme heavy duty design. – L L T

Basic version supplemented with:External screws are stainless/acid resistant,sizes 112 and 132, only in the terminal box63 series ball bearings at both ends, sizes 112 and 132 only at D end.Stainless steel rating plate.Sizes 200-250, special terminal boxSizes 160 and 180: grease nipples.

425 Corrosion protected stator and rotor core. R T T T

Cooling system053 Metal fan cover. L L S S

The dimension L1, L2 and L respectively is increased by 7.5 mmfor the frame size 112 and 5.5 mm for the frame size 132.

068 Aluminium fan. L L L LMandatory for ambient temperatures:For sizes 63-100, >80°C, For sizes 112-250, > 50 °C.

183 Separate motor cooling (fan axial, N-end) R L L L

Dimension drawing141 Binding dimension drawing L L L L

Variant codes

S Included as standard.L On modification of a stocked motor, or on new manufacture,

the number per order may be limited.T New manufacture only.R On request.

1) Certain variant codes cannot be used simultaneously.2) From SEMOT stock.

32 ABB Motors

Drain holes065 Plugged drain holes. – L L L066 Modified drain hole position. IP 54 for sizes 63-100. L L L L

Specify IM designation.076 Drain holes with plugs. L – – –

Holes are sealed with a felt plug. Corrosion protected rotor. IP 55.IM designation must be stated.

Earthing bolt067 External earthing bolt. L L L L

Earthing screw for connection of external protective earth.

Hazardous environments094 EEx n design

Non-sparking, acc. to BS 5000 part 16 and L L L LEx na acc. to IEC 79-15.Data for standard motors applies to temperature classes T1-T3.T4-T6 to special order.

097 EEx e design. Increased safety version. T L L LThe dimension L1, L2 and L respectively is increased by 7.5 mmfor the frame size 112 and 5.5 mm for the frame size 132.IM designation must be stated.

Heating elementsMotor size Element capacity63-71 8 W80-160 25 W180-250 50 W

450 Heating element 100-120 V. L L L L451 Heating element 200-240 V. L L L L

Insulation systems014 Winding insulation class H. T T T T405 Special winding insulation for frequency converter supply R T T T

rated voltage >500 V.406 Winding for supply >690 -1000 V. – R R R

Mounting arrangements007 IM 3001 flange mounted, IEC flange, from IM 1001 (B5 from B3). – – – L

Large flange with clearance holes.

008 IM 2101 foot/flange mounted, IEC flange, from IM 1001 (B34 from B3). L L – –Small flange with tapped holes.

009 IM 2001 foot/flange mounted, IEC flange, from IM 1001 (B35 from B3). L L L LLarge flange with clearance holes.

047 IM 3601 flange mounted, IEC flange, from IM 3001 (B14 from B5),flange mounted motor with large flange. L L – –Small flange with tapped holes.

048 IM 3001 flange mounted, IEC flange, from IM 3601 (B5 from B14),flange mounted motor with small flange. L – – –Large flange with clearance holes.

078 (IM 3601) Flange mounted, DIN C-flange. L – – –Small flange with tapped holes.Larger flange than standard version.

080 (IM 3001) Flange mounted, DIN A-flange, L – – –Large flange with clearance holes.Larger flange than standard version.

090 (IM 2101) foot/flange mounted, DIN C-flange,from IM 1001 (B34 from B3). L – – –Small flange with tapped holes.Larger flange than standard version.

091 (IM 2001) foot/flange mounted, DIN A-flange,from IM 1001 (B35 from B3). L – – –Large flange with clearance holes.Larger flange than standard version.

Painting114 Special paint colour, standard grade. L L L L179 Special paint specification. – R R R

Protection005 Protective roof, vertical motor, shaft down. L L L L

Vertically mounted motors with shaft extension downwards.

072 Radial seal at D-end. T L L LOnly flange mounted motors for sizes 63-100.

403 Degree of protection IP 56.Dust proof version. Water from waves which – L L Lsplash over must not enter in serious quantities.


63-100 112-132 160-180 200-250


the number per order may be limited.T New manufacture only.R On request.

1) Certain variant codes cannot be used simultaneously.

33ABB Motors


63-100 112-132 160-180 200-250

Rating and instruction plates002 Restamping voltage, frequency, and output. Continuous duty. L L L L

All data to be specified in the order.003 Individual serial number. L L L L013 Restamping to output for class F temperature rise. L R R R

Applies to variants with temperature rise to class B as standard.

095 Restamping of output. Maintained voltage and frequency. Intermittent duty. L L L L

All data to be specified in order.

098 Stainless rating plate. L L L L138 Mounting of additional identification plate. L L L L139 Additional indentification plate delivered loose. L L L L

Shaft and rotor069 Two shaft extensions as per basic catalogue. T T T T

Standard shaft material.

070 One or two special shaft extensions, standard shaft material. T T T T

164 Shaft extension with closed key-way. T S S S

410 Stainless/acid-proof steel shaft, standard or non-standard design. T T T TOne or two shaft extensions.

Standards and regulations010 Fulfilling CSA requirements. T L L L

029 Fulfilling Underwriters Laboratory (UL) requirements. T – – –

Stator winding temperature sensorsBreaking capacity for bimetal detector:Size 63-1002 A at 380 V vs5 A at 240 V vs2.5 A at 24 V lsSize 112-2504 A at 250 V vs3 A at 60 V ls

121 Bimetal detectors, break type (NCC), L L2) L2) L2)(3 in series), 130°C, in stator winding.2 in series for 71-100. Size 63, new manufacture only.

122 Bimetal detectors, break type (NCC), L L2) L2) L2)(3 in series), 150 °C, in stator winding.2 in series for 71-100. Size 63, new manufacture only.

123 Bimetal detectors, break type (NCC), L L2) L2) L2)(3 in series), 170 °C, in stator winding.2 in series for 71-100. Size 63, new manufacture only.

125 Bimetal detectors, break type (NCC), L L2) L2) L2)(2x3 in series), 150 °C, in stator winding.2 x 2 in series for 71-100. Size 63, new manufacture only.

127 Bimetal detectors, break type (NCC), L L2) L2) L2)(3 in series, 130 °C & 3 in series , 150 °C), in stator winding.2 x 2 in series for 71-100. Size 63, new manufacture only.

435 PTC - thermistors L L2) L2) L2)(3 in series), 130 °C, 3 in stator winding.Two speed motors, only for new manufacture.Tripping device, more information from ABB Control.

436 PTC thermistors. L L2) L2) S150 °C, 3 in series.Two speed motors, only for new manufacture.Tripping device, more information from ABB Control.

437 PTC - thermistors L L2) L2) L2)(3 in series), 170 °C, in stator winding.Two speed motors, only for new manufacture.Tripping device, more information from ABB Control.

439 PTC - thermistors L L2) L2) L2)(2x3 in series), 150 °C, in stator winding.Two speed motors, only for new manufacture.Tripping device, more information from ABB Control.

441 PTC - thermistors L L2) L2) L2)(3 in series, 130 °C, & 3 in series, 150 °C), in stator winding.Two speed motors, only for new manufacture.Tripping device, more information from ABB Control.

442 PTC - thermistors L L2) L2) L2)(3 in series, 150 °C & 3 in series , 170 °C), in stator winding.Two speed motors, only for new manufacture.Tripping device, more information from ABB Control.

1) Certain variant codes cannot be used simultaneously.2) Two speed motors, new manufacture only.


the number per order may be limitedT New manufacture only.R On request.

34 ABB Motors


63-100 112-132 160-180 200-250

445 PT100 – L2) L2) L2)(1 per phase) in stator winding. Measurement current max. 10 mA.Temperature: 0 10 20 50 100 150°CResistance: 100 103.9 107.7 119.3 138.5 158 OhmMonitoring unit, more information from ABB Network Partner.

446 PT100 – – L2) L2)(2 per phase) in stator winding. Measurement current max. 10 mA.Temperature: 0 10 20 50 100 150°CResistance: 100 103.9 107.7 119.3 138.5 158 OhmMonitoring unit, more information from ABB Network Partner.

Terminal box015 ∆ connection in terminal box, (reconnection from Y.) L S S S

Single speed motors only.

017 Y connection in terminal box (reconnection from ∆.) L S S SSingle speed motors only.

019 Larger than standard terminal box. R – L LStandard for 200-250, voltage code S.

021 Terminal box on left-hand side, seen from D-end. – – – T

180 Terminal box on right-hand side, seen from D-end. – – – T

136 Extended cable connection, standard terminal box. L R R R2 m long connection cable.

137 Extended cable connection, low terminal box. T T T TSizes 63-100: terminal box without screw terminals,2 m long connection cable.Sizes 112-250: 2 m long flying leads.

187 Cable glands of non-standard design. R R R R

230 One standard cable gland, mounted RHS (seen from D-end). L L L L

402 Terminal box adapted for Al cables. – – – T

418 Separate terminal box for temperature detectors. R T L L

467 Lower than standard terminal box and rubber extended cable. – L L TTerminal box without screw terminals and extended rubberconnection cable, 3 m.

M2AA 112-180 have standard terminal box with low, flat cover.

731 Two standard cable glands, mounted RHS (seen from D-end). – L L L

Testing140 Test confirmation. L L L L

145 Type test report from test of identical motor. R L L L400 V 50 Hz.

146 Type test with report for motor from specific delivery batch. T L L L

147 Type test report with motor from specific delivery batch, T L L Lcustomer witnessed.

148 Routine test report. R L L L

149 Test according to separate test specification. R L L L

Variable speed drivesFor long cables, see code 405 ”Insulation systems”.

182 Pulse sensor mounted as specified. R R R R

470 Prepared for hollow shaft pulse tacho. T T T L(Leine & Linde equivalent).

472 1024 of pulse tacho. T T T L(Leine & Linde equivalent).Hollow shaft version.

473 2048 of pulse tacho. T T T L(Leine & Linde equivalent).Hollow shaft version.

474 Separate motor cooling and prepared for T T T Thollow shaft pulse tacho (Leine & Linde equivalent).

476 Separate motor cooling (fan axial, N-end) – R R Tand 1024 pulse tacho (Leine & Linde equivalent).

477 Separate motor cooling (fan axial, N-end) – R R Tand 2048 pulse tacho (Leine & Linde equivalent).

Y/∆∆∆∆∆ starting117 Terminals for Y/∆ start – – T T

at both speeds(two separate windings).

118 Terminals for Y/∆ start – T T Tat high speed(two separate windings).

1) Certain variant codes cannot be used simultaneously.2) Two speed motors, new manufacture only.

S Included as standard.L On modification of a stocked motor, or on new manufacture, the number per

order may be limited.T New manufacture only.R On request.

35ABB Motors

TypeM2AA FA1) G GA GB GC H1) HA HC HD HE K KA L LC UB VA VB VC VD

632) - 11 16 9.5 - 63 7 123 150 50.5 7 10 213 241 Pr 18.6, Pg 11 31 92 30.5 61.571 - 11 16 9.5 - 71 9 141 172 62.5 7 11 239 268 Pr 22.5, Pg 16 34 92 30.5 61.580 5 15.5 21.5 11 16 80 10 159 192 68.5 10 14 272 307 Pr 22.5, Pg 16 37.5 100 33 67

90 S 5 20 27 11 16 90 10 179 212 79.5 10 14 295 330 Pr 22.5, Pg 16 43.5 100 33 6790 L 5 20 27 11 16 90 10 179 212 79.5 10 14 320 355 Pr 22.5, Pg 16 43.5 100 33 67100 L 6 24 31 15.5 21.5 100 12 199 236 93.5 12 14 358.5 403 Pr 22.5, Pg 16 47 100 33 67

Dimension dra wings

IM 3081, IM 3082, IM B 5

TypeM2AA HB LA M N P S T

632) 87 9 115 95 140 10 363 87 9 130 110 160 10 3.571 101 9 130 110 160 10 3.580 112 10 165 130 200 12 3.5

90 S 122 10 165 130 200 12 3.590 L 122 10 165 130 200 12 3.5100 L 136 11 215 180 250 15 4

IM 3681, IM 3682, IM B 14


632) 87 8 75 60 90 M5 2.571 101 10 85 70 105 M6 2.580 112 10 100 80 120 M6 3

90 S 122 14 115 95 140 M8 390 L 122 14 115 95 140 M8 3100 L 136 16 130 110 160 M8 3.5

1) TolerancesA, B ISO js14D, DA ISO j6F, FA ISO h9H +0 -0.5N ISO j6C, CA ±0.8

Foot-mounted motor IM 1081, IM 1082, IM B 3

M2AA 63-100Basic design and high-output design

Flange-mounted motor, large flangeIM 3081, IM 3082, IM B 5

Flange-mounted motor,small flangeIM 3681, IM 3682, IM B 14

2) M2AA 63 can be supplied with shaft extension D = 11,E = 23, F = 4 and GA = 12.5 mm, and DB = M4,if B5 flange M = 115 mm.

3) Alternative version of additional shaft extension forM2AA 63 and M2AA 71.

IM 1081, IM 1082, IM B 3

TypeM2AA A1) AA AB AC AE B1) BA BB C1) CA CB D1) DA1) DB DC E2) EA EG EH F1)

632) 100 16 120 120 85 80 14 98 40 68 9 14 11 M5 M4 30 23 12.5 10 571 112 20 136 140 85 90 21 112 45 80 11 14 11 M5 M4 30 23 12.5 10 580 125 25 154 158 97 100 20 125 50 87 12.5 19 14 M8 M5 40 30 19 12.5 6

90 S 140 27 170 178 97 100 30 125 56 94 12.5 24 14 M8 M5 50 30 19 12.5 890 L 140 27 170 178 97 125 30 150 56 94 12.5 24 14 M8 M5 50 30 19 12.5 8100 L 160 32 197 198 97 140 34 172 63 100 16 28 19 M10 M8 60 40 22 19 8

36 ABB Motors

1) TolerancesA, B ISO js14D, DA ISO j6F, FA ISO h9H +0 -0.5N ISO j6C, CA ±0.8

2) M2AA 63 can be supplied with shaft extension D = 11,E = 23, F = 4 and GA = 12.5 mm, and DB = M4,if B5 flange M = 115 mm.

3) Alternative version of additional shaft extension forM2AA 63 and M2AA 71.

TypeM2AA FA1) G GA GB GC H1) HA HC HD HE K KA L LC UB VA VB VC VD

632) - 11 16 9.5 - 63 7 123 150 50.5 7 10 213 241 Pr 18.6, Pg 11 31 92 30.5 61.571 - 11 16 9.5 - 71 9 141 172 62.5 7 11 239 268 Pr 22.5, Pg 16 34 92 30.5 61.580 5 15.5 21.5 11 16 80 10 159 192 68.5 10 14 272 307 Pr 22.5, Pg 16 37.5 100 33 67

90 S 5 20 27 11 16 90 10 179 212 79.5 10 14 295 330 Pr 22.5, Pg 16 43.5 100 33 6790 L 5 20 27 11 16 90 10 179 212 79.5 10 14 320 355 Pr 22.5, Pg 16 43.5 100 33 67100 L 6 24 31 15.5 21.5 100 12 199 236 93.5 12 15 358,5 403 Pr 22.5, Pg 16 47 100 33 67

IM 2081, IM 2082, IM B 35


632) 87 9 115 95 140 10 363 87 9 130 110 160 10 3.571 101 9 130 110 160 10 3.580 112 10 165 130 200 12 3.5

90 S 122 10 165 130 200 12 3.590 L 122 10 165 130 200 12 3.5100 L 136 11 215 180 250 15 4

IM 2181, IM 2182, IM B 34


632) 87 8 75 60 90 M5 2.571 101 10 85 70 105 M6 2.580 112 10 100 80 120 M6 3

90 S 122 14 115 95 140 M8 390 L 122 14 115 95 140 M8 3100 L 136 16 130 110 160 M8 3.5

M2AA 63-100Basic and high output design

Foot- and flange-mounted motorIM 2081, IM 2082, IM B 35, large flange

Foot- and flange-mounted motorIM 2181, IM 2182, IM B 34, small flange

IM 2081, IM 2082, IM B 35, IM 2181, IM 2182, IM B 34

TypeM2AA A1) AA AB AC AE B1) BA BB C1) CA CB D1) DA1) DB DC E2) EA EG EH F1)

632) 100 16 120 120 85 80 14 98 40 68 9 14 11 M5 M4 30 23 12.5 10 571 112 20 136 140 85 90 21 112 45 80 11 14 11 M5 M4 30 23 12.5 10 580 125 25 154 158 97 100 20 125 50 87 12.5 19 14 M8 M5 40 30 19 12.5 6

90 S 140 27 170 178 97 100 30 125 56 94 12.5 24 14 M8 M5 50 30 19 12.5 890 L 140 27 170 178 97 125 30 150 56 94 12.5 24 14 M8 M5 50 30 19 12.5 8100 L 160 32 197 198 97 140 34 172 63 100 16 28 19 M10 M8 60 40 22 19 8

37ABB Motors

M2AA 63-100Special design with DIN flang eBasic design and high-output design

Type Flange designation Flange dimensions

M2AA IEC DIN LA M N P S T

631) FF 115 A 140 9 115 95 140 9 371 FF 165 A 200 10 165 130 200 12 3.580 FF 215 A 250 11 215 180 250 15 4

90 S FF 215 A 250 11 215 180 250 15 490 L FF 215 A 250 11 215 180 250 15 4100 L FF 265 A 300 12 265 230 300 15 4

1) Smaller than corresponding IEC flange.

DIN A-flange. Large flange with clearance holes.Smaller than large flange of basic design.Only available on request.

DIN A-flange. Large flange with clearance holes.Larger than large flange of basic design.See variant codes 080 and 091, respectively.



71 FF 115 A 140 9 115 95 140 10 380 FF 130 A 160 9 130 110 160 10 3.5

90 S FF 130 A 160 9 130 110 160 10 3.590 L FF 130 A 160 9 130 110 160 10 3.5100 L FF 165 A 200 10 165 130 200 12 3.5

Note: Dimensions C, L and LC are 15 mm longer than in the standard version.

DIN C-flange. Large flange with tapped holes.Larger than small flange of basic design.See variant codes 078 and 090, respectively.

Flange-mounted (IM 3081, IM B 5) and foot-and flange-mounted motor (IM 2081, IM B 35),respectively.

Flange-mounted (IM 3081, IM B 5) and foot-and flange-mounted motor (IM 2081, IM B 35),respectively.

Flange-mounted (IM 3681, IM B 14) andfoot- and flange-mounted motor(IM 2181, IM B 34), respectively.



71 FT 115 C 140 12 115 95 140 M8 380 FT 130 C 160 12 130 110 160 M8 3.5

90 S FT 130 C 160 15 130 110 160 M8 3.590 L FT 130 C 160 15 130 110 160 M8 3.5100 L FT 165 C 200 15 165 130 200 M10 3.5

38 ABB Motors

M2AA 112, 132Basic design

IM 3001, IM B 5

TypeM2AA HB LA M N1) P S T

112 146 11 215 180 250 14.5 4132 163.5 14 265 230 300 14.5 4

IM 3601, IM B 14


112 146 20 130 110 160 M8 3.5132 163.5 18 165 130 200 M10 3.5

IM 1001, IM B 3

TypeM2AA A1) AA AB AC AE B1) B' BA BB BC C1) CA' 1) 4) CA1) 5) CB D1) DA1) DB DC E2) EA EG EH F1) FA1) G

112 M 190 41 222 221 160 140 - 31 168 31 70 111.5 138 14 28 19 M10 M8 60 40 22 19 8 6 24132 S 216 47 262 261 160 140 1788) 40 212 76 89 158 191 18 38 24 M12 M8 80 50 28 19 10 8 33132 M 216 47 262 261 160 1408) 178 40 212 76 89 120 153 18 38 24 M12 M8 80 50 28 19 10 8 33

TypeM2AA GA GB GC H1) HA HC HD HE K L14) L25) LC14) LC25) UB13) UB23) VA VB VC6) VD17) VD27)

112 M 31 15.5 21.5 112 12 226 258 92 12 361 388 421.5 448 Pr 22.5, Pg 16 Pr 28.3, Pg 21 60 160 80 120 40132 S 41 20 27 132 14 263.5 295.5 109.5 12 447 447 517 517 Pr 22.5, Pg 16 Pr 28.3, Pg 21 71 160 80 120 40132 M 41 20 27 132 14 263.5 295.5 109.5 12 447 481.5 517 550 Pr 22.5, Pg 16 Pr 28.3, Pg 21 71 160 80 120 40

1) TolerancesA, B ISO js14C, CA +0 -2D28 ISO j6D38 ISO k6DA ISO j6F, FA ISO h9H +0 -0.5N ISO j6

2) Shoulder of shaft extension and contact surface of flange are in the same plane.3) Knockout openings4) Single-speed motors and two-speed motors 132 S.

For variant code 053 and 097 the dimension L1 and L2 is increased by 7.5 mmfor the frame size 112 and 5.5 mm for the frame size 132.

5) Two-speed motors, exkl. 132 S.6) Dimensions to UB1.7) Dimensions to UB2 (VD1 = right side, VD2 = left side) as viewed from the D-end.8) Not acc. to IEC.

Flange-mounted motor, small flangeIM 3601, IM 3602, IM B 14

Foot-mounted motor IM 1001, IM 1002, IM B 3 Flange-mounted motor, large flangeIM 3001, IM 3002, IM B 5

39ABB Motors

M2AA 112, 132Basic design

IM 2001, IM B 35


112 146 11 215 180 250 14.5 4132 163.5 14 265 230 300 14.5 4

IM 2101, IM B 34


112 146 20 130 110 160 M8 3.5132 163.5 18 165 130 200 M10 3.5

TypeM2AA GA GB GC H1) HA HC HD HE K L14) L25) LC14) LC25) UB13) UB23) VA VB VC6) VD17) VD27)

112 M 31 15.5 21.5 112 12 226 258 92 12 361 388 421.5 448 Pr 22.5, Pg 16 Pr 28.3, Pg 21 60 160 80 120 40132 S 41 20 27 132 14 263.5 295.5 109.5 12 447 447 517 517 Pr 22.5, Pg 16 Pr 28.3, Pg 21 71 160 80 120 40132 M 41 20 27 132 14 263.5 295.5 109.5 12 447 481.5 517 550 Pr 22.5, Pg 16 Pr 28.3, Pg 21 71 160 80 120 40

Foot- and flange-mounted motor, IM 2101, IM 2102, IM B 34, small flange

IM 2001, IM 2002, IM B 35

TypeM2AA A1) AA AB AC AE B1) B' 1) BA BB BC C1) CA' 1) 7) CA1) 7) CB D1) DA1) DB DC E2) EA EG EH F1) FA1) G

112 M 190 41 222 221 160 140 - 31 168 31 70 111.5 138 14 28 19 M10 M8 60 40 22 19 8 6 24132 S 216 47 262 261 160 140 1788) 40 212 76 89 158 191 18 38 24 M12 M8 80 50 28 19 10 8 33132 M 216 47 262 261 160 1408) 178 40 212 76 89 120 153 18 38 24 M12 M8 80 50 28 19 10 8 33

2) Shoulder of shaft extension and contact surface of flange are in the same plan.3) Knockout openings.4) Single-speed motors and two-speed motors 132 S.

For variant code 053 and 097 the dimension L1 and L2 is increased by 7.5 mmfor the frame size 112 and 5.5 mm for the frame size 132.

5) Two-speed motors, 132 S not included .6) Dimension to UB1.7) Dimension to UB2 (VD1 = right side, VD2 = left side) as viewed from the D-end.8) Not acc. to IEC.

Foot- and flange-mounted motor, IM 2001, IM 2002, IM B 35, large flange


40 ABB Motors

M2AA 112, 132High-output design

Foot-mounted motor IM 1001, IM 1002, IM B 3 Flange-mounted motor, large flangeIM 3001, IM 3002, IM B 5

Flange-mounted motor, small flangeIM 3601, IM 3602, IM B 14


TypeM2AA GB GC H1) HA HC HD HE K L7) LC UB13) UB23) VA VB VC4) VD15) VD25)

112 M 15.5 21.5 112 12 226 258 92 12 388 448 Pr 22.5, Pg 16 Pr 28.3, Pg 21 60 160 80 120 40132 S 20 27 132 14 263.5 295.5 109.5 12 481.5 550 Pr 22.5, Pg 16 Pr 28.3, Pg 21 71 160 80 120 40132 M 20 27 132 14 263.5 295.5 109.5 12 481.5 550 Pr 22.5, Pg 16 Pr 28.3, Pg 21 71 160 80 120 40

IM 3001, IM B 5


112 146 11 215 180 250 14.5 4132 163.5 14 265 230 300 14.5 4

IM 3601, IM B 14


112 146 20 130 110 160 M8 3.5132 163.5 18 165 130 200 M10 3.5

IM 1001, IM 1002, IM B 3

TypeM2AA A1) AA AB AC AE B1) B' 1) BA BB BC C1) CA' 1)7) CA1)7)CB D1) DA1) DB DC E2) EA EG EH F1) FA1) G GA

112 M 190 41 222 221 160 140 - 31 168 31 70 - 138 14 28 19 M10 M8 60 40 22 19 8 6 24 31132 S 216 47 262 261 160 140 1786) 40 212 76 89 153 191 18 38 24 M12 M8 80 50 28 19 10 8 33 41132 M 216 47 262 261 160 1406)178 40 212 76 89 153 191 18 38 24 M12 M8 80 50 28 19 10 8 33 41

2) Shoulder of shaft extension and contact surface of flange are in the same plane.3) Four knockout openings.4) Dimension to UB1.5) Dimension to UB2 (VD1 = right side, VD2 = left side) as viewed from the D-end.6) Not acc. to IEC.7) For variant code 053 and 097 the dimension L is increased by 7.5 mm

for the frame size 112 and 5.5 mm for the frame size 132.

41ABB Motors

M2AA 112, 132High-output design

Foot-mounted and flange-mounted motor, IM 2101, IM 2102, IM B 34, small flange

IM 2001, IM B 35


112 146 11 215 180 250 14.5 4132 163.5 14 265 230 300 14.5 4

IM 2101, IM B 34


112 146 20 130 110 160 M8 3.5132 163.5 18 165 130 200 M10 3.5

TypeM2AA GA GB GC H1) HA HC HD HE K L7) LC UB13) UB23) VA VB VC4) VD15) VD25)

112 M 31 15.5 21.5 112 12 226 258 92 12 388 448 Pr 22.5, Pg 16 Pr 28.3, Pg 21 60 160 80 120 40132 S 41 20 27 132 14 263.5 295.5 109.5 12 481.5 550 Pr 22.5, Pg 16 Pr 28.3, Pg 21 71 160 80 120 40132 M 41 20 27 132 14 263.5 295.5 109.5 12 481.5 550 Pr 22.5, Pg 16 Pr 28.3, Pg 21 71 160 80 120 40


IM 2001, IM 2002, IM B 35

TypeM2AA A1) AA AB AC AE B1) B' 1) BA BB BC C1)7) CA' 1)7) CA1) CB D1) DA1) DB DC E2) EA EG EH F1) FA1) G

112 M 190 41 222 221 160 140 - 31 168 31 70 - 138 14 28 19 M10 M8 60 40 22 19 8 6 24132 S 216 47 262 261 160 140 1786) 40 212 76 89 153 191 18 38 24 M12 M8 80 50 28 19 10 8 33132 M 216 47 262 261 160 1406) 178 40 212 76 89 153 191 18 38 24 M12 M8 80 50 28 19 10 8 33

2) Shoulder of shaft extension and contact surface of flange are in the same plan.3) Knockout openings.4) Dimension to UB1.5) Dimension to UB2 (VD1 = right side, VD2 = left side) as viewed from the D-end.6) Not acc. to IEC.7) For variant code 053 and 097 the dimension L is increased by 7.5 mm

for the frame size 112 and 5.5 mm for the frame size 132.

Foot-mounted and flange-mounted motor, IM 2001, IM 2002, IM B 35, large flange

42 ABB Motors



2) Knockout openings.3) M-2, MA-2, M-4, M-6, M-8, MA-8, L-2, L-4, L-6,

MA-2/4, M-2/4, L-2/4, M-4/6, M-4/8, LB-2 and LB-44) L-8, L-4/6, L-4/8, LB-6 and LB-85) M-2, M-4, L-4, L-6, L-8, M-2/4, M-4/6, M-4/8 and LB-26) L-2/4, L-4/6, L-4/8, LB-4, LB-6 and LB-87) 160 M: B' not acc. to IEC

160 L: B not acc. to IEC180 M: B' not acc. to IEC180 L: B not acc. to IEC

1) TolerancesA, B ISO js14C, CA +0 -2D, DA ISO k6F, FA ISO h9H +0 -0.5

IM 1001, IM 1002, IM B 3

TypeM2AA A1) AA AB AC AE B1)7) B' 1)7) BA BB BC C1) CA1) CA' 1) CB D1) DA1) DB DC E EA EG EH F1)

160 3) 254 56 310 310 210 210 254 50 287.5 86 108 185.5 141.5 20 42 32 M16 M12 110 80 36 28 12160 4) 254 56 310 310 210 210 254 50 287.5 86 108 226.5 182.5 20 42 32 M16 M12 110 80 36 28 12180 5) 279 65.5 340 360 210 241 279 58 316 88 121 218 180 25 48 32 M16 M12 110 80 36 28 14180 6) 279 65.5 340 360 210 241 279 58 316 88 121 238 200 25 48 32 M16 M12 110 80 36 28 14

TypeM2AA FA1) G GA GB GC H1) HA HC HD HE K L LC UB2) UB22) VA VB VC VD VE

160 3) 10 37 45 27 35 160 20 325 368.5 130 15 602.5 693.5 Pr 37, Pg 29 Pr 15.4, Pg 9 89 210 84.5 134.5 167.5160 4) 10 37 45 27 35 160 20 325 368.5 130 15 643.5 734.5 Pr 37, Pg 29 Pr 15.4, Pg 9 89 210 84.5 134.5 167.5180 5) 10 42.5 51.5 27 35 180 20 360 403.5 145 15 680 770 Pr 37, Pg 29 Pr 15.4, Pg 9 77.5 210 84.5 134.5 167.5180 6) 10 42.5 51.5 27 35 180 20 360 403.5 145 15 700.5 790 Pr 37, Pg 29 Pr 15.4, Pg 9 77.5 210 84.5 134.5 167.5

43ABB Motors

Flange-mounted motor IM 3001, IM 3002, IM B 5


1) TolerancesD, DA ISO k6F, FA ISO h9N ISO j6

2) Knockout openings.

3) M-2, MA-2, M-4, M-6, M-8, MA-8, L-2, L-4, L-6,MA-2/4, M-2/4, L-2/4, M-4/6, M-4/8, LB-2 and LB-4

4) L-8, L-4/6, L-4/8, LB-6 and LB-85) M-2, M-4, L-4, L-6, L-8, M-2/4, M-4/6, M-4/8 and LB-26) L-2/4, L-4/6, L-4/8, LB-4, LB-6 and LB-87) Shoulder of shaft extension and contact surface of flange are in the same plane.

TypeM2AA L LA LB LC M N1) P S T UB12) UB22) VA VB VC VD VE

160 3) 602.5 16 492.5 693.5 300 250 350 19 5 Pr 37, Pg 29 Pr 15.4, Pg 9 89 210 84.5 134.5 167.5160 4) 643.5 16 533.5 734.5 300 250 350 19 5 Pr 37, Pg 29 Pr 15.4, Pg 9 89 210 84.5 134.5 167.5180 5) 680 21 570 770 300 250 350 19 5 Pr 37, Pg 29 Pr 15.4, Pg 9 77.5 210 84.5 134.5 167.5180 6) 700.5 21 590.5 790 300 250 350 19 5 Pr 37, Pg 29 Pr 15.4, Pg 9 77.5 210 84.5 134.5 167.5

IM 3001, IM 3002, IM B 5

TypeM2AA AC AE D1) DA1) DB DC E7) EA EG EH F1) FA1) G GA GB GC HB HE

160 3) 310 210 42 32 M16 M12 110 80 36 28 12 10 37 45 27 35 208.5 130160 4) 310 210 42 32 M16 M12 110 80 36 28 12 10 37 45 27 35 208.5 130180 5) 360 210 48 32 M16 M12 110 80 36 28 14 10 42.5 51.5 27 35 223.5 145180 6) 360 210 48 32 M16 M12 110 80 36 28 14 10 42.5 51.5 27 35 223.5 145

44 ABB Motors

Foot- and flange-mounted motor IM 2001, IM 2002, IM B 35

M2AA 160-180Basic design and high-output design

1) TolerancesA, B ISO js14C, CA +0 -2D, DA ISO k6F, FA ISO h9H +0 -0.5N ISO j6

2) Knockout openings.3) M-2, MA-2, M-4, M-6, M-8, MA-8, L-2, L-4, L-6,

MA-2/4, M-2/4, L-2/4, M-4/6, M-4/8, LB-2 and LB-44) L-8, L-4/6, L-4/8, LB-6 and LB-85) M-2, M-4, L-4, L-6, L-8, M-2/4, M-4/6, M-4/8 and LB-26) L-2/4, L-4/6, L-4/8, LB-4, LB-6 and LB-87) Shoulder of shaft extension and contact surface of

flange are in the same plan.8) 160 M: B' not acc. to IEC

160 L: B not acc. to IEC180 M: B' not acc. to IEC180 L: B not acc. to IEC

IM 2001, IM 2002, IM B 35

TypeM2AA A1) AA AB AC AE B1)8) B' 1)8) BA BB BC C1) CA1) CA' 1) CB D1) DA1) DB DC E7) EA EG EH F1)

160 3) 254 56 310 310 210 210 254 50 287.5 86 108 185.5 141.5 20 42 32 M16 M12 110 80 36 28 12160 4) 254 56 310 310 210 210 254 50 287.5 86 108 226.5 182.5 20 42 32 M16 M12 110 80 36 28 12180 5) 279 65.5 340 360 210 241 279 58 316 88 121 218 180 25 48 32 M16 M12 110 80 36 28 14180 6) 279 65.5 340 360 210 241 279 58 316 88 121 238 200 25 48 32 M16 M12 110 80 36 28 14

TypeM2AA FA1) G GA GB GC H1) HA HB HC HD HE K L LA LB LC M N1) P S

160 3) 10 37 45 27 35 160 20 208.5 325 368.5 130 15 602.5 16 492.5 693.5 300 250 350 19160 4) 10 37 45 27 35 160 20 208.5 325 368.5 130 15 643.5 16 533.5 734.5 300 250 350 19180 5) 10 42.5 51.5 27 35 180 20 223.5 360 403.5 145 15 680 21 570 770 300 250 350 19180 6) 10 42.5 51.5 27 35 180 20 223.5 360 403.5 145 15 700.5 21 590.5 790 300 250 350 19

TypeM2AA T UB2) UB22) VA VB VC VD VE

160 3) 5 Pr 37, Pg 29 Pr 15.4, Pg 9 89 210 84.5 134.5 167.5160 4) 5 Pr 37, Pg 29 Pr 15.4, Pg 9 89 210 84.5 134.5 167.5180 5) 5 Pr 37, Pg 29 Pr 15.4, Pg 9 77.5 210 84.5 134.5 167.5180 6) 5 Pr 37, Pg 29 Pr 15.4, Pg 9 77.5 210 84.5 134.5 167.5

45ABB Motors

M2AA 200-250


Basic design

Type IEC- No. ofM2AA size poles F1) FA1) G GA GB GC H1) HA HD HE K L LC UB2) VA VB VC3) VC4) VD3) VD4)

200 ML. 200 M 2-8 16 16 49 59 39 49 200 25 499 221 18 773 893 2 x FL 13 75.5 243 118 89.5 168 163.5200 ML. 200 L 2-8 16 16 49 59 39 49 200 25 499 221 18 773 893 2 x FL 13 75.5 243 118 89.5 168 163.5

225 SM. 225 S 4, 8 18 16 53 64 49 59 225 25 544.5 241 18 865 985 2 x FL 13 93.5 243 118 89.5 168 163.5225 SM. 225 M 2, 2/4 16 16 49 59 49 59 225 25 544.5 241 18 835 955 2 x FL 13 93.5 243 118 89.5 168 163.5225 SM. 225 M 4-8 18 16 53 64 49 59 225 25 544.5 241 18 865 985 2 x FL 13 93.5 243 118 89.5 168 163.5

250 SM. 250 S 2 18 16 53 64 49 59 250 40 592.5 264 22 872 992 2 x FL 13 93.5 243 118 89.5 168 163.5250 SM. 250 S 4-8 18 16 58 69 49 59 250 30 592.5 264 22 872 992 2 x FL 13 93.5 243 118 89.5 168 163.5

250 SM. 250 M 2 18 16 53 64 49 59 250 40 592.5 264 22 872 992 2 x FL 13 93.5 243 118 89.5 168 163.5250 SM. 250 M 2/4 18 16 53 64 49 59 250 30 592.5 264 22 872 992 2 x FL 13 93.5 243 118 89.5 168 163.5250 SM. 250 M 4-8 18 16 58 69 49 59 250 30 592.5 264 22 872 992 2 x FL 13 93.5 243 118 89.5 168 163.5

IM 1001, IM 1002, IM B 3

Type IEC- No. ofM2AA size poles A1) AA AB AC AE B1) B'1) BA BB C1) CA1) CA' 1) CB D1) DA1) DB DC E EA EG EH

200 ML. 200 M 2-8 318 64 380 386 243 267 3055) 98 365 133 273 235 30 55 45 M20 M16 110 110 42 36200 ML. 200 L 2-8 318 64 380 386 243 2675) 305 98 365 133 273 235 30 55 45 M20 M16 110 110 42 36

225 SM. 225 S 4, 8 356 69 418 425 243 286 3115) 84 360 149 300 275 24.5 60 55 M20 M20 140 110 42 42225 SM. 225 M 2, 2/4 356 69 418 425 243 2865) 311 84 360 149 300 275 24.5 55 55 M20 M20 110 110 42 42225 SM. 225 M 4-8 356 69 418 425 243 2865) 311 84 360 149 300 275 24.5 60 55 M20 M20 140 110 42 42

250 SM. 250 S 2 406 78 474 471 243 311 3495) 94.5 409 168 263 225 40 60 55 M20 M20 140 110 42 42250 SM. 250 S 4-8 406 78 474 471 243 311 3495) 94.5 409 168 263 225 30 65 55 M20 M20 140 110 42 42

250 SM. 250 M 2, 2/4 406 78 474 471 243 3115) 349 94.5 409 168 263 225 40 60 55 M20 M20 140 110 42 42250 SM. 250 M 4-8 406 78 474 471 243 3115) 349 94.5 409 168 263 225 30 65 55 M20 M20 140 110 42 42

2) Flange opening is provided with pipe flange FL 13, with tappedlead-in holes plugged with sealing plugs.Single- and two-speed motors: 2 x Pr 37, 2 x Pg 29Motors for 230 V 50 Hz have pipe flange FL 21 and 2 x Pr 54, 2 x Pg 42.

3) For flange opening FL 13: 2 x Pr 37, 2 x Pg 294) For extra large terminal box with flange opening FL 21: 2 x Pr 54, 2 x Pg 42.5) Not acc. to IEC.

1) TolerancesA, B ISO js14C, CA +0 -2DA 45-55 ISO k6D 55-65 ISO m6F, FA ISO h9H +0 -0.5

46 ABB Motors

M2AA 200-250


Basic design

M2AA 225-250

M2AA 200

IM 3001, IM 3002, IM B 5

Type IEC- No. ofM2AA size poles AC AE D1) DA1) DB DC E2) EA EG EH F1) FA G GA GB GC HB HE

200 ML. 200 M 2-8 386 243 55 45 M20 M16 110 110 42 36 16 16 49 59 39 49 299 221200 ML. 200 L 2-8 386 243 55 45 M20 M16 110 110 42 36 16 16 49 59 39 49 299 221

225 SM. 225 S 4, 8 427 243 60 55 M20 M20 140 110 42 42 18 16 53 64 49 59 319.5 241225 SM. 225 M 2, 2/4 427 243 55 55 M20 M20 110 110 42 42 16 16 49 59 49 59 319.5 241225 SM 225 M 4-8 427 243 60 55 M20 M20 140 110 42 42 18 16 53 64 49 59 319.5 241

250 SM. 250 S 2 471 243 60 55 M20 M20 140 110 42 42 18 16 53 64 49 59 342.5 264250 SM. 250 S 4-8 471 243 65 55 M20 M20 140 110 42 42 18 16 58 69 49 59 342.5 264

250 SM. 250 M 2, 2/4 471 243 60 55 M20 M20 140 110 42 42 18 16 53 64 49 59 342.5 264250 SM. 250 M 4-8 471 243 65 55 M20 M20 140 110 42 42 18 16 58 69 49 59 342.5 264

Type IEC- No. ofM2AA size poles L LA LB LC M N1) P S T UB3) VA VB VC4) VC5) VD4) VD5)

200 ML. 200 M 2-8 773 20 663 893 350 300 400 19 5 2 x FL 13 75.5 243 118 89.5 168 163.5200 ML. 200 L 2-8 773 20 663 893 350 300 400 19 5 2 x FL 13 75.5 243 118 89.5 168 163.5

225 SM. 225 S 4, 8 865 22 725 985 400 350 450 19 5 2 x FL 13 93.5 243 118 89.5 168 163.5225 SM. 225 M 2, 2/4 835 22 725 955 400 350 450 19 5 2 x FL 13 93.5 243 118 89.5 168 163.5225 SM. 225 M 4-8 865 22 725 985 400 350 450 19 5 2 x FL 13 93.5 243 118 89.5 168 163.5

250 SM. 250 S 2 872 22 732 992 500 450 550 19 5 2 x FL 13 93.5 243 118 89.5 168 163.5250 SM. 250 S 4-8 872 22 732 992 500 450 550 19 5 2 x FL 13 93.5 243 118 89.5 168 163.5

250 SM. 250 M 2, 2/4 872 22 732 992 500 450 550 19 5 2 x FL 13 93.5 243 118 89.5 168 163.5250 SM. 250 M 4-8 872 22 732 992 500 450 550 19 5 2 x FL 13 93.5 243 118 89.5 168 163.5

1) TolerancesDA 45-55 ISO k6D 55-65 ISO m6F, FA ISO h9N ISO js6

2) Shoulder of shaft extension and contact surface of flange are in the same plane.3) Flange opening is provided with pipe flange FL 13, with tapped

lead-in holes plugged with sealing plugs.Single- and two-speed motors: 2 x Pr 37, 2 x Pg 29Motors for 230 V 50 Hz have pipe flange FL 21 and 2 x Pr 54, 2 x Pg 42.

4) For flange opening FL 13: 2 x Pr 37, 2 x Pg 295) For extra large terminal box with flange opening FL 21: 2 x Pr 54, 2 x Pg 42.

47ABB Motors

M2AA 200-250


Basic design

M2AA 225-250

M2AA 200

IM 2001, IM 2002, IM B 35

Type IEC- No. ofM2AA size poles A1) AA AB AC AE B1) B'1) BA BB C1) CA1) CA' 1) CB D1) DA1) DB DC E5) EA EG EH F1) FA1) G GA

200 ML. 200 M 2-8 318 64 380 386 243 267 3056) 98 365 133 273 235 30 55 45 M20 M16 110 110 42 36 16 16 49 59200 ML. 200 L 2-8 318 64 380 386 243 2676) 305 98 365 133 273 235 30 55 45 M20 M16 110 110 42 36 16 16 49 59

225 SM. 225 S 4, 8 356 69 418 425 243 286 3116) 84 360 149 300 275 24.5 60 55 M20 M20 140 110 42 42 18 16 53 64225 SM. 225 M 2, 2/4 356 69 418 425 243 2866) 311 84 360 149 300 275 24.5 55 55 M20 M20 110 110 42 42 16 16 49 59225 SM. 225 M 4-8 356 69 418 425 243 2866) 311 84 360 149 300 275 24.5 60 55 M20 M20 140 110 42 42 18 16 53 64

250 SM. 250 S 2 406 78 474 471 243 311 3496) 94.5 409 168 263 225 40 60 55 M20 M20 140 110 42 42 18 16 53 64250 SM. 250 S 4-8 406 78 474 471 243 311 3496) 94.5 409 168 263 225 30 65 55 M20 M20 140 110 42 42 18 16 58 69

250 SM. 250 M 2, 2/4 406 78 474 471 243 3116) 349 94.5 409 168 263 225 40 60 55 M20 M20 140 110 42 42 18 16 53 64250 SM. 250 M 4-8 406 78 474 471 243 3116) 349 94.5 409 168 263 225 30 65 55 M20 M20 140 110 42 42 18 16 58 69

Type IEC- No. ofM2AA size poles GB GC H1) HA HD HE K L LA LB LC M N1) P S T UB2) VA VB VC3) VC4) VD3) VD4)

200 ML. 200 M 2-8 39 49 20025 499 221 18 773 20 663 893 350 300 400 19 5 2 x FL 13 75.5 243 118 89.5 168 163.5200 ML. 200 L 2-8 39 49 20025 499 221 18 773 20 663 893 350 300 400 19 5 2 x FL 13 75.5 243 118 89.5 168 163.5

225 SM. 225 S 4, 8 49 59 22525 544.5 241 18 865 22 725 985 400 350 450 19 5 2 x FL 13 93.5 243 118 89.5 168 163.5225 SM. 225 M 2, 2/4 49 59 22525 544.5 241 18 835 22 725 955 400 350 450 19 5 2 x FL 13 93.5 243 118 89.5 168 163.5225 SM. 225 M 4-8 49 59 22525 544.5 241 18 865 22 725 985 400 350 450 19 5 2 x FL 13 93.5 243 118 89.5 168 163.5

250 SM. 250 S 2 49 59 25040 592.5 264 22 872 22 732 992 500 450 550 19 5 2 x FL 13 93.5 243 118 89.5 168 163.5250 SM. 250 S 4-8 49 59 25030 592.5 264 22 872 22 732 992 500 450 550 19 5 2 x FL 13 93.5 243 118 89.5 168 163.5

250 SM. 250 M 2 49 59 25040 592.5 264 22 872 22 732 992 500 450 550 19 5 2 x FL 13 93.5 243 118 89.5 168 163.5250 SM. 250 M 2/4 49 59 25030 592.5 264 22 872 22 732 992 500 450 550 19 5 2 x FL 13 93.5 243 118 89.5 168 163.5250 SM. 250 M 4-8 49 59 25030 592.5 264 22 872 22 732 992 500 450 550 19 5 2 x FL 13 93.5 243 118 89.5 168 163.5

1) TolerancesA, B ISO js14C, CA +0 -2D 55-65 ISO m6DA 45-55 ISO k6F, FA ISO h9H +0 -0.5N ISO js6

2) Flange opening is provided with pipe flange FL 13, with tappedlead-in holes plugged with sealing plugs.Single- and two-speed motors: 2 x Pr 37, 2 x Pg 29Motors for 230 V 50 Hz have pipe flange FL 21 and 2 x Pr 54, 2 x Pg 42.

3) For flange opening FL 13: 2 x Pr 37, 2 x Pg 294) For extra large terminal box with flange opening FL 21: 2 x Pr 54, 2 x Pg 42.5) Shoulder of shaft extension and contact surface of flange are in the same plane.6) Not acc. to IEC.

48 ABB Motors


M2AA 200-250High-output design

IM 1001, IM 1002, IM B 3

Type IEC- No.ofM2AA size poles A1) AA AB AC AE B'1) BA BB C1) CA1) CA' 1) CB D1) DA1) DB DC E EA EG EH

200 ML. 200 L 2-8 318 64 380 386 243 305 98 365 133 273 235 30 55 45 M20 M16 110 110 42 36

225 SM. 225 M 2 356 69 418 425 243 311 84 360 149 300 275 24.5 55 55 M20 M20 110 110 42 42225 SM. 225 M 4-8 356 69 418 425 243 311 84 360 149 300 275 24.5 60 55 M20 M20 140 110 42 42

250 SM. 250 M 2 406 78 474 471 243 349 94.5 409 168 263 225 30 60 55 M20 M20 140 110 42 42250 SM. 250 M 4-8 406 78 474 471 243 349 94.5 409 168 263 225 30 65 55 M20 M20 140 110 42 42

Type IEC- No. ofM2AA size poles F1) FA1) G GA GB GC H1) HA HD HE K L LC UB2) VA VB VC3) VC4) VD3) VD4)

200 ML. 200 L 2-8 16 16 49 59 39 49 200 25 499 221 18 773 893 2 x FL 13 75.5 243 118 89.5 168 163.5

225 SM. 225 M 2 16 16 49 59 49 59 225 25 544.5 241 18 835 955 2 x FL 13 93.5 243 118 89.5 168 163.5225 SM. 225 M 4-8 18 16 53 64 49 59 225 25 544,5 241 18 865 985 2 x FL 13 93.5 243 118 89.5 168 163.5

250 SM. 250 M 2 18 16 53 64 49 59 250 40 592.5 264 22 872 992 2 x FL 13 93.5 243 118 89.5 168 163.5250 SM. 250 M 4-8 18 16 58 69 49 59 250 30 592.5 264 22 872 992 2 x FL 13 93.5 243 118 89.5 168 163.5

1) TolerancesA, B ISO js14C, CA +0 -2DA 42 ISO k6D, DA 55-60 ISO m6F, FA ISO h9H +0 -0.5

2) Flange opening is provided with pipe flange FL 13, with tappedlead-in holes plugged with sealing plugs, 2 x Pr 37, 2 x Pg 29.

3) For flange opening FL 13: 2 x Pr 37, 2 x Pg 29.4) For extra large terminal box with flange opening FL 21: 2 x Pr 54, 2 x Pg 42.

Dimension AD and HD refer to sidemounted terminal box, see page 51.

49ABB Motors

High-output design


M2AA 200-250

M2AA 200

IM 3001, IM 3002, IM B 5

Type IEC- No. ofM2AA size poles AC AE D1) DA1) DB DC E2) EA EG EH F1) FA G GA GB GC HB HE

200 ML. 200 L 2-8 386 243 55 45 M20 M16 110 110 42 36 16 16 49 59 39 49 299 221

225 SM. 225 M 2 427 243 55 55 M20 M20 110 110 42 42 16 16 49 59 49 59 319.5 241225 SM. 225 M 4-8 427 243 60 55 M20 M20 140 110 42 42 18 16 53 64 49 59 319.5 241

250 SM. 250 M 2 471 243 60 55 M20 M20 140 110 42 42 18 16 53 64 49 59 342.5 264250 SM. 250 M 4-8 471 243 65 55 M20 M20 140 110 42 42 18 16 58 69 49 59 342.5 264

Type IEC- No. ofM2AA size poles L LA LB LC M N P S T UB3) VA VB VC4) VC5) VD4) VD5)

200 ML. 200 L 2-8 773 20 663 893 350 300 400 19 5 2 x FL 13 75.5 243 118 89.5 168 163.5

225 SM. 225 M 2 835 22 725 955 400 350 450 19 5 2 x FL 13 93.5 243 118 89.5 168 163.5225 SM. 225 M 4-8 865 22 725 985 400 350 450 19 5 2 x FL 13 93.5 243 118 89,5 168 163.5

250 SM. 250 M 2 872 22 732 992 500 450 550 19 5 2 x FL 13 93.5 243 118 89.5 168 163.5250 SM. 250 M 4-8 872 22 732 992 500 450 550 19 5 2 x FL 13 93.5 243 118 89.5 168 163.5

1) TolerancesDA 42 ISO k6D, DA 55-60 ISO m6F, FA ISO h9N ISO js6

2) Shoulder of shaft extension and contact surface offlange are in the same plane.

3) Flange opening is provided with pipe flange FL 13, with tapped lead-in holesplugged with sealing plugs.Single- and two-speed motors: 2 x Pr 37, 2 x Pg 29Motors for 230 V 50 Hz have pipe flange FL 21 and 2 x Pr 54, 2 x Pg 42.

4) For flange opening FL 13: 2 x Pr 37, 2 x Pg 29.5) For extra large terminal box with flange opening FL 21: 2 x Pr 54, 2 x Pg 42

M2AA 225-250

50 ABB Motors

M2AA 200-250


High-output design

M2AA 225-250

M2AA 200

Type IEC- No. ofM2AA size poles GB GC H1) HA HD HE K L LA LB LC M N1) P S T UB2) VA VB VC3) VC4) VD3) VD4)

200 ML. 200 L 2-8 39 49 200 25 499 221 18 773 20 663 893 350 300 400 19 5 2 x FL 13 75.5 243 118 89.5 168 163.5

225 SM. 225 M 2 49 59 225 25 544.5 241 18 835 22 725 955 400 350 450 19 5 2 x FL 13 93.5 243 118 89.5 168 163.5225 SM. 225 M 4-8 49 59 225 25 544.5 241 18 865 22 725 985 400 350 450 19 5 2 x FL 13 93.5 243 118 89.5 168 163.5

250 SM. 250 M 2 49 59 250 40 592.5 264 22 872 22 732 992 500 450 550 19 5 2 x FL 13 93.5 243 118 89.5 168 163.5250 SM. 250 M 4-8 49 59 250 30 592.5 264 22 872 22 732 992 500 450 550 19 5 2 x FL 13 93.5 243 118 89.5 168 163.5

IM 2001, IM 2002, IM B 35

Type IEC- No.ofM2AA size poles A1) AA AB AC AE B1) B'1) BA BB C1) CA1) CA' 1) CB D1) DA1) DB DC E5) EA EG EH F1) FA1) G GA

200 ML. 200 L 2-8 318 64 380 386 243 267 305 98 365 133 273 235 30 55 45 M20 M16 110 110 42 36 16 16 49 59

225 SM. 225 M 2 356 69 418 425 243 286 311 84 360 149 300 275 24.5 55 55 M20 M20 110 110 42 42 16 16 49 59225 SM. 225 M 4-8 356 69 418 425 243 286 311 84 360 149 300 275 24.5 60 55 M20 M20 140 110 42 42 18 16 53 64

250 SM. 250 M 2 406 78 474 471 243 311 349 94.5 409 168 263 225 40 60 55 M20 M20 140 110 42 42 18 16 53 64250 SM. 250 M 4-8 406 78 474 471 243 311 349 94.5 409 168 263 225 30 65 55 M20 M20 140 110 42 42 18 16 58 69

1) TolerancesA, B ISO js14C, CA +0 -2D 55-65 ISO m6DA 45-55 ISO k6F, FA ISO h9H +0 -0.5N ISO j6

2) Flange opening is provided with pipe flange FL 13, with tappedlead-in holes plugged with sealing plugs, 2 x Pr 37, 2 x Pg 29.

3) For flange opening FL 13: 2 x Pr 37, 2 x Pg 29.4) For extra large terminal box with flange opening FL 21: 2 x Pr 54, 2 x Pg 42.5) Shoulder of shaft extension and contact surface of flange are in the same plane.

51ABB Motors

Protective roof

Code 005 Vertically mounted motors with shaftextension downwards

Type No. of DimensionM2AA IEC-size poles L

63 22371 25080 282

90 S 30590 L 330100 L 368

112 M Single-speed motors 400132 S 484132 M 484

112 M Two-speed motors and 428132 S high-output design 522132 M 522

160 1) 730160 2) 771180 3) 813.5180 4) 834

200 ML. 200 M 2-8 823225 SM. 225 M 2, 2/4 885225 SM. 225 M 4-8 915

250 SM. 250 S 2-8 922250 SM. 250 M 2-8 922

Terminal box

Code 019 Larger than standard terminal boxType DimensionsM2AA AD HB HD

200 ML. 328.5 328.5 528.5225 SM. 349 349 574250 SM. 372 372 622

Code 021 Terminal box on left-hand side, seen from D endCode 180 Terminal box on right-hand side, seen from Dend

Type DimensionsM2AA AD HD

200 ML. 296.5 393225 SM. 317 437.5250 SM. 340 485.5

Kod 467 Lower than standard terminal box without screwterminals and extended rubber connection cable,3 m.M2AA 112-180 has standard terminal box withlow, flat cover.

Type DimensionsM2AA AD HB HD

112 M 123.5 235.5132 S 141 273132 M 141 273

160 211.5 371.5180 226.5 406.5

200 ML. 248 248 448225 SM. 269 269 494250 SM. 292 292 542

Dimensions f or alternative designs

1) M-2, MA-2, M-4, M-6, M-8, MA-8, L-2, L-4, L-6. MA-2/4, M-2/4, L-2/4, M-4/6,M-4/8, LB-2 and LB-4.

2) L-8, L-4/6, L-4/8, LB-6 and LB-8.3) M-2, M-4, L-4, L-6, L-8, M-2/4, M-4/6, M-4/8 and LB-2.4) L-2/4, L-4/6, L-4/8, LB-4, LB-6 and LB-8.

52 ABB Motors

Accessories

Slide railsThe slide rails are manufactured from steel. Each ordernumber includes two complete slide rails, includingfixing screws, for the motor. Fixing screws for the sliderails are not included. Slide rails are supplied with roughlower surfaces and, prior to tightening down, should besupported in a suitable manner.

MSP-0, -1, -2 and -3 MSP-4 and -5

DimensionsKA KB Motor Weight/pair

Type for screw for screw X XB XE Y YA YB Z ZA bolt kg

MSP-0 M10 - 330 305 12.5 30 - - 35 6 M6 1.5MSP-1 M10 - 330 305 12.5 30 - - 35 6 M8 1.5MSP-2 M12 - 495 465 15 40 - - 37 6 M10 2.5MSP-3 M16 - 595 550 22.5 50 . . 40 10 M12 3.5MSP-4 M20 - 720 680 20 - - 80 45 20 M16 9.5MSP-5 M24 M16 900 850 25 200 150 100 50 25 M20 14.5

Ordering tab leMotor Catalogue

Type size XA min. XA max. XC XF No.

MSP-0 63 105 210 45 0 MK 911 011-171 111 201 40 0

MSP-1 80 118 188 40 0 MK 911 011-290 125 180 40 0

MSP-2 100 145 275 45 70 MK 911 011-3112 151 314 40 25132 171 294 40 0

MSP-3 160 207 342 50 0 MK 911 011-4180 210 340 40 0

MSP-4 200 280 400 90 45 MK 911 011-5225 274 406 65 35

MSP-5 250 337 513 100 0 MK 911 011-6

53ABB Motors

Foundation studsFoundation studs are intended for use instead of baseplates. Each set of foundation studs includes four studs.Fixing screws for mounting the motor and two conicalpins for locking the motor in position on the foundationstuds are supplied.

Ordering tableMotor Weight/kit Cataloguesize B1 B2 D d g H h S p kg No.

112, 132 60 90 25 M10 25 125 8 30 200 3 MK 911 974-AA160,180 70 110 25 M12 35 150 10 35 200 4 MK 911 975-AA200, 225 80 140 28 M16 35 180 10 40 250 7 MK 911 976-AA250 100 150 35 M20 40 200 10 50 270 10 MK 911 977-AA

Touch-up paintTouch-up paint in spray cans, gross content 400 ml. The paint is of alkydbase type.

Order no. Language on label

3GZ V 515 001-34 Swedish, Finnish, Norwegian and Danish

3GZ V 515 001-35 English, German, French and Spanish

Aluminium motors in brief. Basic design.Size 63 71 80 90 100

Stator and feet Material Diecast aluminium alloy. Feet integrated with stator.Surface treatment One-component modified polyester paint. Munsell blue 8B 4.5/3.25 / NCS 4822 BO5G. >30 µm.

Bearing end shields Material Diecast aluminium alloy.Surface treatment One-component modified polyester paint. Munsell blue 8B 4.5/3.25 / NCS 4822 BO5G. >30 µm.

Bearings D-end 6202-2Z/C3 6203-2Z/C3 6204-2Z/C3 6305-2Z/C3 6306-2Z/C3Single-speed motors N-end 6202-2Z/C3 6202-2Z/C3 6203-2Z/C3 6204-2Z/C3 6205-2Z/C3

Bearings D-end 6202-2Z/C3 6203-2Z/C3 6204-2Z/C3 6305-2Z/C3 6306-2Z/C3Two-speed motors N-end 6202-2Z/C3 6202-2Z/C3 6203-2Z/C3 6204-2Z/C3 6205-2Z/C3

Axially-locked Inner bearing cover 1) 1) 1) D-end D-endbearings 1) Foot motor. A spring-washer at the N-end presses the rotor towards the D-end.

Bearing seals D-end V ring.N-end Labyrinth seal.

Lubrication Permanently lubricated bearings. Grease for bearing temperatures -25 to +150 °C.

Terminal box Material Diecast aluminium alloy.Surface treatment Similar to stator.Screws Steel 5 G. Galvanised and yellow chromated.

Connections Knockout openings 4 x Pr 18.6 4 x Pr 22.54 x Pg 11 4 x Pg 16

Terminal box Screw terminal. 6 terminals.Max Cu-area, mm2 2.5

Fan Material Polypropylene. Reinforced with 20% glass fibre.

Fan hood Material Polypropylene.

Stator winding Material Copper.Impregnation Polyester varnish. Tropicalised.Insulation class Insulation class F. Temperature rise class B, unless otherwise stated.

Stator winding See "Stator winding temperature sensors " in the catalogue on p. 10, 33 and 34.temperature sensors

Rotor winding Material Diecast aluminium.

Enclosure IP 55.

Cooling method IC 411.

Drain holes Variant code 066 or 076.

54A

BB

Motors

Aluminium moto rs in brief . Basic design (cont)Size 112 132 S 132 M 160 180 200 225 250

Stator Material Diecast aluminium alloy. Extruded aluminium alloy.

Surface treatment Polyester powder paint. Munsell blue 8B 4.5/3.25 / NCS 4822 BO5G. >50 µm.

Feet Material Aluminium alloy. Integrated with the stator. Aluminium alloy, bolted to the stator. 250-2, castiron

Bearing end shields Material Diecast aluminium alloy. Flanged bearing end shields of cast iron. Other diecast aluminium alloy

Surface treatment Polyester powder paint. Munsell blue 8B 4.5/3.25 / NCS 4822 BO5G. >50 µm.

Bearings D-end 6206-2Z/C3 6208-2Z/C3 6208-2Z/C3 6209-2Z/C3 6210-2Z/C3 6312/C3 6313/C3 6315/C3Single-speed motors N-end 6205-2Z/C3 6206-2Z/C3 6206-2Z/C3 6209-2Z/C3 6209-2Z/C3 6210/C3 6212/C3 6213/C3

Bearings D-end 6206-2Z/C3 6208-2Z/C3 6208-2Z/C3 6209-2Z/C3 6210-2Z/C3 6312/C3 6313/C3 6315/C3Two-speed motors N-end 6206-2Z/C3 6206-2Z/C3 6208-2Z/C3 6209-2Z/C3 6209-2Z/C3 6210/C3 6212/C3 6213/C3

Axially-locked Inner bearing cover 1) D-end1) D-end1) D-end D-end N-end N-end N-endbearings 1) Foot motors. A spring-washer at the N-end presses the rotor towards the D-end.

Flange-mounted motors: Inner bearing cover and spring-washer at the N-end.

Bearing seals D-end V ring. Outer and inner V rings.N-end Two-speed motors sizes 112 and 132 M, V ring. Other labyrinth seal. Outer and inner V rings.

Lubrication Permanently lubricated bearings. Valve lubrication.Grease for bearing temperatures -30 to +110 °C. Grease for bearing temperatures -30 to +110 °C.

Terminal box Material Diecast aluminium alloy. Base integrated with stator. Deep-drawn steel sheet, bolted to stator.

Surface treatment Similar to stator. Phosphated. Polyester paint.

Screws Steel. Galvanised and chromated.

Connections Knockout openings 2 x (Pr 28.3 + Pr 22.5) 4 x Pr 37 + 2 x Pr 15,42 x (Pg 21 + Pg 16) 4 x Pg 29 + 2 x Pg 9

Flange openings 2 x FL 13, 2 x Pr 372 x Pg 29

Flange openings for 2 x FL 21, 2 x Pr 54voltage code S 2 x Pg 42

Terminal box Cable lugs. 6 terminals.

Screws M5 M5 M5 M6 M6 M10 M10 M10Max Cu-area, mm2 10 10 10 35 35 70 70 70

Fan Material Polypropylene. Reinforced with 20% glass fibre.

Fan hood Material Polypropylene. See also note 1). Steel sheet. 1) 1) Also two-speed motorsSurface treatment Phosphated. Polyester paint.1) sizes 112 and 132 M.

Stator winding Material Copper.Impregnation Polyester varnisch. Tropicalised.Insulation class Insulation class F. Temperature rise class B, unless otherwise stated.

Stator winding See "Stator winding temperature sensors " in the catalogue on p. 10, 33. PTC thermistors. 150 °C. 3 in series.temperatur sensors

Rotor winding Material Diecast aluminium.

Enclosure IP 55.

Cooling method IC 411.

Drain holes Drain holes with closable plastic plugs. Open on delivery.

AB

B M

otors55

ABB Motors56

ABB Motors product range

Motor type/application IEC frame sizes Output kW

Three-phase motors, IP 55 63 - 400 0.18 - 710Ex nA motors 63 - 400 0.18 - 630EEx e motors 63 - 400 0.18 - 390EEx d/EEx de motors 80 - 400 0.55 - 630Marine motors 63 - 400 0.18 - 630IP 23 S open drip proof motors 250 - 400 75 - 800Single-phase motors 63 - 100 0.15 - 2.2Brake motors 71 - 400 0.25 - 710Integral motors 80 - 132 0,75 - 7,5

Basic alternatives– aluminium, steel and cast iron frames available

– LV motors up to 1000 V

– standard versions of all types kept in stock

– larger LV and HV motors can also be supplied

– motors according to NEMA-standard

Special types/alternatives– special variable speed AC drives

– high speed motors, over 3000 r/min

– traction motors

– generators for wind mills

– roller tables and mines

– water cooled motors

– slip-ring motors

– motors with vertical hollow shaft

– smoke venting design

– stator/rotor units

ABB Motors' new range of aluminium motors meet the highest efficiency and operationalreliability levels demanded by many of today's industrial processes.

Catalogues and brochures for thesemotors are available from:

ABB MotorsBusiness AreaMarketing CommunicationsP.O. Box 633FIN-65101 VAASA, FinlandTel. +358 10 22 4000Fax +358 10 224 7372

57ABB Motors

ABB's aluminium motors play an important role in the efficient andreliable operation of Atlas Copco's compressors. The compressors aredesigned to be operationally quiet, light weight and of compact designfor ease of positioning. These are attributes which aluminium motorsadequately match.

An aluminium motor, M2AA framesize 250, being fitted on a twin-boom Atlas Copco jumbo drill rig.

58ABB Motors

ABB Motors' new aluminium series covers a vast applicationrange. Shown here is the 45 kW type M2AA 225 SMB, 5.5 kWtype M2AA 132 SA and 1.5 kW type M2AA 90 L.

BearingsModern bearings have high load capacityand run silently. The bearing housing wasdeveloped jointly with SKF.

Bearing seal, D-endThe motors are fitted with enclosed 2Zbearings as standard. A V-ring on the shaftprotects the bearing from dirt and moisture.

Terminal boxCable lugs are used for secure connections. Thespacious terminal box makes connecting themotor quick and easy. Cables can enter fromthe left or the right.

Rotor windingThe rotor winding is made of pressure die-cast aluminium, a design that provides highstarting capacity and low noise level.

InsulationHigh-grade insulation and generouselectrical dimensioning give themotor a high overload capacity.

Typical modern totally-enclosed squirrel-cage three-phase motorType M2AA 132 M, 7.5 kW IP 55 IC 411 1450 r/min, weight 48 kg

LubricationThe motors have closed bearing housings and thebearings are lubricated for life. Nipples for lubricationin service can be fitted.

Stator frameThe stator frame is made of pressure die-cast extracorrosion-resistant aluminium alloy. The motor has greatmechanical strength and a good surface finish.

Bearing seal, N-endThe motors are fitted with enclosed 2Zbearings as standard. A labyrinth sealprotects the bearing from dirt and moisture.

ISO 9001 certificateABB Motors is certified under the ISO9001 international quality standard. Thismakes ABB Motors a reliable supplierwith comprehensive service.

Cooling fanThe high efficiency of the motormeans that a smaller, quiter fan canbe used.

Corrosion protectionEffective, strong corrosion protectionmeans that the motor can be used in allenvironments.

ABB Motors59-60

SE920774

ABB Motors

The Leader in Motors

ABB Group is the world's leading electrical enginee-ring company supplying expertise and products forelectric power generation, transmission, and distri-bution as well as industrial and rail transportationmarkets. ABB supplies a full range of industrialelectric motors, both AC and DC, LV and HVmeeting the needs of most applications, withvirtually any power rating.

Within the Group, ABB Motors is the world's leadingmanufacturer of low-voltage induction motors,having over 100 years experience and a presence inmore than 140 countries. ABB Motors' broadunderstanding of customer applications enables it towork closely to solve individual problems or tosupply custom-designed motors for any project – nomatter how demanding.

For customers, this all represents a solid value andcommitment revealed in the dependable quality ofABB Motor's products and in its unrivalled customer

61

service and back up. The hallmarks of its productsare efficiency, robustness and reliability, combinedto represent the best value available. Customers theworld over rely on ABB Motors as the most solidand reliable supplier of electric motors. But aboveall, ABB Motors values its customers.

The best value is also enhanced by ABB Motors'worldwide customer service network guaranteeingfast delivery, rapid response and local back-up, aswell as by worldwide ABB Service network support-ing the after sales service.

ABB Motors' manufacturing facilities are located inDenmark, Finland, Italy, Spain, Sweden, India andMexico. The comprehensive motor stocks at eachof these sites are reinforced by a large andversatile stocks at Central Stock Europe Germanyand Central Stock Asia, Singapore, and bynumerous distribution stocks.

Catalogue BA/M2AA GB 96-10

ABB MotorsBusiness Area Marketing CommunicationsP.O.Box 633FIN-65101 Vaasa FinlandTel. +358 10 22 4000Fax +358 10 22 47372

ABB MotorsManufacturing sites (*) and some of the biggest sales companies.

Finland*ABB Motors OyP.O.Box 633FIN-65101 Vaasatel. +358 10 22 4000fax +358 10 224 7372

FranceABB Industrie15, rue SullyF-69153 Décines CharpieuCedextel. +33 (0) 472 054 040fax +33 (0) 472 020 345

GermanyABB Elektromotoren GmbHP.O.Box 10 01 24D-66001 Saarbrückentel. +49 (0) 681 81091fax +49 (0) 681 810 9523

Hong KongAsea Brown Boveri Ltd3 Dai Hei StreetTai Po Industrial EstateTai Po New TerritoriesHong Kongtel. +852 292 938 38fax +852 292 935 05

India*Asea Brown Boveri LtdP.O.Box 16Faridabad 121 001tel. +91 (0) 129 233 313fax +91 (0) 129 234 288

IndonesiaP.T. Abdibangun BuanaP.O.Box 3781Jakarta 10002tel. +62 (0) 21 314 9115fax +62 (0) 21 315 3963

IrelandAsea Brown Boveri LtdComponents DivisionBelgard RoadTallaght, Dublin 24tel. +353 (0) 1 405 7300fax +353 (0) 1 405 7327

Italy*ABB Industria S.p.a.Motor DivisionViale Edison 50I-20099 Sesto S. Giovanni,Milanotel. +39 (0) 2 262 321fax +39 (0) 2 262 32723

SwitzerlandABB Normelec AGBadenerstrasse 790PostfachCH-8048 Zürichtel. +41 (0) 1 435 6666fax +41 (0) 1 435 6603

TaiwanAsea Brown Boveri LtdP.O.Box 81-54Taipeitel. +886 (0) 2 579 9340fax + 886 (0) 2 577 9434

ThailandAsea Brown Boveri LtdP.O.Box 2087Bangkok 10501tel. +66 (0) 2 249 4825fax +66 (0) 2 249 8479

The United KingdomABB Motors LtdSouth PointSutton Court RoadSutton, Surrey SM1 4 TYtel. +44 (0) 181 395 8585fax +44 (0) 181 395 8991

USAABB Industrial Systems Inc.Drive Products & SystemsP.O.Box 372MilwaukeeWI 53201-0372tel. +1 414 785 3416fax +1 414 785 0397

VenezuelaAsea Brown Boveri S.A.P.O.Box 6649Carmelitas,Caracas 1010Atel. +58 (0) 2 238 2422fax +58 (0) 2 239 6383

AustraliaC.M.G. Electric Motors Pty LtdP.O.Box 484Ringwood, VIC 3134tel. +61 (0) 3 9870 9333fax +61 (0) 3 9879 5060

AustriaABB Industrie Ges.m.b.H.P.O.Box 80A-1101 Wientel. +43 (0) 1 601 090fax +43 (0) 1 601 098 305

BelgiumAsea Brown Boveri S.A.-N.V.Hoge Wei 27B-1930 Zaventemtel. +32 (0) 2 718 6311fax +32 (0) 2 718 6657

BrazilAsea Brown Boveri LtdaP.O.Box 0097506020-902 Osasco -SPtel. +55 (0) 11 704 9111fax +55 (0) 11 702 1991

CanadaAsea Brown Boveri, Inc.Process Automation &Drives Division4410 Paletta CourtBurlington, Ontario L7L 5R2tel. +1 905 681 0565fax +1 905 681 9865

China*ABB Yuejin Motors (Shanghai)Company Limited300, Mei Zhou RoadShanghaifax +86 21 654 38230

ChileAsea Brown Boveri S.A.P.O.Box 581-3Santiagotel. +56 (0) 2 555 0051fax +56 (0) 2 556 9345

Denmark*ABB Motors A/SPetersmindevej 1DK-5000 Odense Ctel. +45 66 147 096fax +45 65 912 912

JapanABB Industry K.K.2-39, Akasaka 5-ChomeMinato-KuTokyo 107tel. +81 (0) 3 556 38605fax +81 (0) 3 556 38615

Mexico*ABB Sistemas, S.A. de C.V.P.O.Box M-243406000 Mexico D.F.tel. +52 5 328 1400fax +52 5 328 1694

The NetherlandsABB Componenten B.V.P.O.Box 532NL-2900 AM Capelle a/d Ijsseltel. +31 (0) 10 258 2250fax +31 (0) 10 4586559

New ZealandABB Industrial Group LtdPrivate Bag 93314Symonds Street, Aucklandtel. + 64 (0) 9 356 2170fax + 64 (0) 9 357 0019

NorwayABB Industri ASP.O.Box 6540 RodelökkaN-0501 Oslo 5tel. +47 22 872 000fax +47 22 872 541

SingaporeAsea Brown Boveri Pte LtdP.O.Box 95Pasir Panjang Post OfficeSingapore 9111tel. +65 775 3777fax +65 778 0222

Spain*ABB Motores S.A.P.O.Box 81E-08200 Sabadelltel. +34 (9) 3 728 8500fax +34 (9) 3 728 8554

Sweden*ABB Motors ABS-721 70 Västeråstel. +46 (0) 21 329 000fax +46 (0) 21 124 103

Aluminium motors · ABB Motors This product catalogue contains electrical and mechanical data on...

Documents

Transcript of Aluminium motors · ABB Motors This product catalogue contains electrical and mechanical data on...