AllFive Clear - ESIcms.esi.info/Media/documents/Fager_industrial_ML.pdf · 196 • A B B + Reﬂ...

www.fagerhult.com • www.fagerhult.co.uk196

A B B + Refl ector B + Refl ector asym

W B C D1/2x14 622 150 50 4831/2x28 1222 150 50 10831/2x35/49 1522 150 50 1383

AB

C

D

14 W

A

AllFive Clear

Luminaire with HF-std

W kg Light dist.

FDH

1x14 1,3 A 33401

2x14 1,3 B 33402

1x28 2,2 A 33403

2x28 2,3 B 33404

1x35 2,6 A 33405

2x35 2,8 B 33406

1x49 2,6 A 33407

2x49 2,8 B 33408

The luminaire can be supplied with through-wiring 5x1.5 mm2, add -143 after the catalogue number.

Accessories

Refl ector 2x14W 97590

Refl ector 2x28W 97591

Refl ector 2x35/49W 97592

Spare cover clear 14W 90310


Spare cover clear 35/49W 90312

Cable wire bracket/pair 91334

Wire suspension, 2x1,5m/pair 91162

White enamelled wall bracket 90°/each 91508

Ceiling bracket, fl exible c/c /pair 91213

Shelter bracket/pair 91210

Luminaire with emLED

W kg Light dist.

FDH

1x28 2,2 A 33403-203

1x35 2,6 A 33405-203

InstallationSurface mounted, cable wire, wire suspension or horizontally on a wall. Installation using the seal supplied with the luminaire provides protection classifi cation IP 44. Without seals the lumin-aire is classifi ed IP 20. Single lamp luminaires are not balanced therefore cable wire installations should be avoided.ConnectionFour Ø 19 mm access holes with blanking grommets on top of the luminaire and one Ø 16 mm knockout in each end. The centrally positioned snap-in ter-minal block 5x2.5 mm2 provides through-wiring. The luminaire is also available with 5x1.5 mm2 through-wiring and snap-in ter-minal blocks at each end (-143). DesignBody in white enamelled, corro-sion resistant aluzinc (NCS 500/RAL 9016). End caps of ASA plastic.Emergency lightingAllFive with emLED available in 1x28W and 1x35W. Information Information about emLED see emLED in the Emergency Lighting chapter. When the seal supplied with the luminaire is used, the protection classifi cation is IP 23. Without seals the luminaire is classifi ed IP 20. LouvreClear cover of extruded acrylic plastic with prismatic underside and lined sides.MiscellaneousTwo tube luminaires, see below.

Installation using the supplied seal, gives classifi cation IP 44.

Refl ectors are available as accessories for the two tube luminaires.

197www.fagerhult.com • www.fagerhult.co.uk

A B

W B C D1/2x14 622 150 50 4831/2x28 1222 150 50 10831/2x35/49 1522 150 50 1383

AB

C

D

14 W

A

AllFive Opal


W kg Light dist.

FDH

1x14 1,3 A 33411

2x14 1,3 B 33412

1x28 2,2 A 33413

2x28 2,3 B 33414

1x35 2,6 A 33415

2x35 2,8 B 33416

1x49 2,6 A 33417

2x49 2,8 B 33418

Accessories



Spare cover clear 35/49W 90317


Wire suspension, 2x1,5 m/pair 91162

White enamelled wall bracket 90°/each 91508

Ceiling bracket, fl exible c/c/pair 91213


Luminaire with emLED

W kg Light dist.

FDH

1x28 2,2 A 33413-203

1x35 2,6 A 33415-203

Body in white enamelled, aluzinc.

InstallationSurface mounted, cable wire, wire suspension or horizontally on a wall. Installation using the seal supplied with the luminaire provides protection classifi cation IP 44. Without seals the lumin-aire is classifi ed IP 20. Single lamp luminaires are not balanced therefore cable wire installations should be avoided.ConnectionFour Ø 19 mm access holes with blanking grommets on top of the luminaire and one Ø 16 mm knockout in each end. The centrally positioned snap-in ter-minal block 5x2.5 mm2 provides through-wiring. The luminaire is also available with 5x1.5 mm2 through-wiring and snap-in ter-minal blocks at each end (-143). DesignBody in white enamelled, corro-sion resistant aluzinc (NCS 500/RAL 9016). End caps of ASA plastic.Emergency lightingAllFive with emLED available in 1x28W and 1x35W. Information about emLED, see emLED in the Emergency Lighting chapter.When the seal supplied with the luminaire is used, the protection classifi cation is IP 23. Without seals the luminaire is classifi ed IP 20. LouvreOpal cover of extruded acrylic plastic.MiscellaneousLuminaire can be completed with shelter brackets.

Ceiling bracket for fl exible c/c available as accessories.

recessed

indu

stria

lpend

ant/su

rfac

e


A A + Refl ector B B + Refl ector

97

W A B C DFD1/2x18 622 206 83 5381/2x36 1232 206 83 11481/2x58 1532 206 83 1448

Ø19

D

AB

C

Allround T8 Clear

Luminaire with conventional ballast

W kg Light dist. Conv. Conv. Thr.-wire.

FD

1x18 2,2 A 33201

2x18 2,2 B 33202 33202-34

1x36 3,5 A 33203 33203-34

2x36 4,4 B 33204 33204-34

1x58 4,6 A 33205 33205-34

2x58 5,8 B 33206

Accessories

Refl ector for 1x36W 97423







Adjustable wall bracket/pair 91375

Wire suspension, 2x1,5 m 91162


Cable wire bracket/pair 91334Luminaire with HF-std

W kg Light dist.

FD

1x18 2,2 A 33201-44

2x18 2,2 B 33202-44

1x36 3,5 A 33203-45

2x36 4,4 B 33204-45

1x58 4,6 A 33205-45

2x58 5,8 B 33206-45

InstallationSurface mounted, cable wire or wire suspension, and horizontally on a wall. Installation using the seals supplied with the luminaire provides protection classifi cation IP 44. Single lamp luminaires are not balanced therefore cable wire installation should be avoided.ConnectionFour Ø 19 mm access holes with blanking grommets - two on top of the luminaire and one at each end. Allround 2x14 and 2x18W with standard HF ballast only has access holes at each end.The centrally positioned snap-in terminal block 5x2.5 mm2 provides through-wiring. The luminaire is also available with 5x1.5 mm2 through-wiring and snap-in terminal blocks at each end. DesignBody in corrosion resistant, white enamelled aluzinc, (NCS0500/RAL 9016). End caps of ABS plastic.LouvreCover of extruded acrylic plastic with prismatic underside and lined sides.MiscellaneousThe luminaire can be supplemen-ted with shelter brackets, see accessories.

The luminaire can be fi tted with a bright aluzinc refl ector, see accessories.

Shelter brackets are available as an accessory.


A B

W A B C DFD1/2x18 622 206 83 5381/2x36 1232 206 83 11481/2x58 1532 206 83 1448

Ø19

D

AB

C

Allround T8 Opal

Accessories

Spare cover opal 18W 90275




Wire suspension, 2x1,5 m 91162




W kg Light dist.

FD

1x18 2,2 A 33211

2x18 2,2 B 33212

1x36 3,5 A 332132x36 4,4 B 332141x58 4,6 A 33215

2x58 5,8 B 33216


W kg Light dist.

FD

1x18 2,2 A 33211-44

2x18 2,2 B 33212-44

1x36 3,5 A 33213-452x36 4,4 B 33214-451x58 4,6 A 33215-45

2x58 5,8 B 33216-45

InstallationSurface mounted, cable wire or wire suspension, and horizontally on a wall. Installation using the supplied seals gives classifi cation IP 44, without seals IP 20. Single lamp luminaires are not balanced therefore cable wire installation should be avoided.ConnectionFour Ø 19 mm access holes with blanking grommets - two on top of the luminaire and one at each end. Allround 2x18W with stan-dard HF ballast only has access holes at each end. The centrally positioned snap-in terminal block 5x2.5 mm2 provides through-wiring. DesignBody in corrosion resistant, white enamelled aluzinc, (NCS 0500/RAL 9016). End caps of ABS plastic.LouvreOpal cover of extruded acrylic plastic.MiscellaneousThe luminaire can be supplemen-ted with shelter brackets.

Installation using seals gives IP 44 classifi cation.

Luminaires fi tted with HF ballast are available as standard in the range.

recessed

indu

stria

lpend

ant/su

rfac

e


A

B

C

W A B C D

FD

2x18 670 181 106 4601x36 1278 111 106 8002x36 1278 181 106 8001x58 1578 111 106 11002x58 1578 181 106 1100

FDH1x28 1278 111 106 8002x28 1278 181 106 8001x35/49 1578 111 106 11002x35/49 1578 181 106 1100

D

A

1x18 670 111 106 460

Accessories



Refl ector for 1x28/36W 99355


Refl ector for 1x35/49/58W 99357


Cover lock of polyoxymethylen plastic or stainless steel

Cover lock in plastic 18W (6 piece) 90370

Cover lock in plastic 28/36W (8 piece) 90371

Cover lock in plastic 35/49/58W (10 piece) 90372

Cover lock in steel 18W (6 piece) 90373

Cover lock in steel 28/36W (8 piece) 90374

Cover lock in steel 35/49/58W (10 piece) 90375



Spare cover

PC SAN

Spare cover for 1x18W 90390 90380


Spare cover for 1x28/36W 90392 90382


Spare cover for 1x35/49/58W 90394 90384


Densus with cable wire bracket 91334.

InstallationSurface mounted, wall, wire and bracket.ConnectionTerminal block 5x4 mm2 at each end. Through-wiring 5x2.5 mm2. Ø 20 mm cable entries fi tted with blanking grommets at each end.DesignBody of glass fi bre reinforced po-lyester. Mounting plate of white fi nished zinc.ShadeShade of styrene acrylic nitrile plastic (SAN) or polycarbonate (PC) with internal shade, longitu-dinal grooves and shade lock of polyoxymethylene plastic respec-tively steel. Both types have an inside rillor along the length.AccessoriesRefl ector of specular anodised aluminium, see accessories.MiscellaneousHF-std luminaires complies with the Swedish Board of Electrical Safety´s demands on limited external temperature (90 °C) at rated voltage.


W kg Light dist. SAN-diffuser PC-diffuser

FD

1x18 2,0 34200-10 35140-10

2x18 2,3 A 34201-10 35141-10

1x36 2,7 34202-10 35142-10

2x36 4,1 A 34203-10 35143-10

1x58 3,4 34204-10 35144-10

2x58 5,5 A 34205-10 35145-10

FDH

1x28 2,4 34206 35146

2x28 3,2 34207 35147

1x35 2,8 34208 35148

2x35 4,0 34209 35149

1x49 2,8 34210 35150

2x49 4,0 34211 35151


W kg Light dist. SAN-diffuser PC-diffuser

FD

1x18 2,0 34200 35140

2x18 2,3 A 34201 35141

1x36 2,7 34202 35142

2x36 4,1 A 34203 35143

1x58 3,4 34204 35144

2x58 5,5 A 34205 35145

Densus

Refl ector as accessory.


1 2

3 4

5 6

1. Cable wire bracket

Made of zinc coated sheet steel.


2. Conduit bracket

Mounting plate of zinc coated sheet steel equipped with hose clips for tubes Ø 45-65 mm. Hose clip can be replaced with those of another dimension.

Conduit bracket/pair 91198

3. Bracket for wire or chain/pair 91221

4. Wire suspension

L=1.5 m, bracket for surface mounting/pair 91541

4. Chain suspension

L=1.0 m, bracket for surface mounting/pair 91543

5. Adjustable ceiling bracket

Bracket of zinc coated 2.0 mm sheet steel. Height 72 mm.

Adjustable ceiling bracket/pair 91374

6. Adjustable wall bracket

Bracket of zinc coated 2.0 mm sheet steel. Length 235 mm.


IndulineAccessories

recessed

indu

stria

lpend

ant/su

rfac

e

178

In addition, Induline has been designed with minimal material usage which

makes the lu mi naire's impact on the en vi ron ment low.

Induline give a wide and useful assortment with the T5 luminaire all advan-

tages.

Designed by Epsilon

Induline is an industrial luminaire especially developed

for the T5 light source.

In this range Fagerhult has utilised the unique

possibilities of the luminaire and tailored a luminaire for

industrial usage.

The wide as sort ment offered by the Induline family

allows for good planning within the industrial sector.

We use MIRO quality to achieve the highest possible

effi ciency.

www.fagerhult.com • www.fagerhult.co.uk

Induline


A B C D

W A B C

1x28 1192 120 1452x28 1192 196 1701x35 1492 120 1452x35 1492 196 1701x49 1492 120 1452x49 1492 196 1701x54 1192 120 1452x54 1192 196 170

AB

C

530

InstallationSurface mounted, wire catenary, conduit, chain and wire suspen-sion as well as lighting track.ConnectionOne Ø 21 mm cable entry fi tted with a blanking grommet at each end. Snap-in terminal block 5x2.5 mm2, placed in the centre with the possibility of through-wiring.DesignBallast box of aluzinc. Assembly rail of extruded aluminium. End caps of cast zinc.LouvreTerazza – louvre with aluminium enamelled cross blades.Luminaires can be supplemented with louvres at a later date.Refl ectorMedium beam refl ector of spe-cular aluminium. The refl ectors are manufactured of MIRO with extremely good refl ective cha-racteristics. Fitted with end caps of aluzinc. The refl ector is easily attached to the luminaire using quick-action lock.MiscellaneousInternal cables are PVC-free. Induline complies with the Swe-dish Board of Electrical Safety's demands on limited external temperatures (90°) at rated voltage.

Luminaire with conduit bracket.

Luminaire with adjustable ceiling bracket.


W kg Light dist.

FDH

Without louvre

1x28 2,1 A 32621

2x28 2,5 B 32624

1x35 2,4 A 32646

2x35 2,8 B 32649

1x49 2,4 A 32671

2x49 2,8 B 32674

1x54 2,1 A 32711

2x54 2,5 B 32714

Louvre Terazza

1x28 2,5 C 32627

2x28 3,2 D 32630

1x35 2,9 C 32652

2x35 3,7 D 32655

1x49 2,9 C 32677

2x49 3,7 D 32680

1x54 2,5 C 32717

2x54 3,2 D 32720

Induline Medium beam

Accessories

Wire cable bracket/pair 91220


Bracket for wire or chain/pair 91221

Wire suspension, L=1,5 m, incl. ceiling bracket/pair 91541

Chain suspension, L=1,0 m, incl. ceiling bracket/pair 91543



recessed

indu

stria

lpend

ant/su

rfac

e


A B C D

W A B C

1x28 1192 165 1652x28 1192 260 1901x35 1492 165 1652x35 1492 260 1901x49 1492 165 1652x49 1492 260 1901x54 1192 165 1652x54 1192 260 190

AB

C

530

InstallationSurface mounted, wire catenary, conduit, chain and wire suspen-sion as well as lighting track.ConnectionOne Ø 21 mm cable entry fi tted with a blanking grommet at each end. Snap-in terminal block 5x2.5 mm2, placed in the centre with the possibility of through-wiring.DesignBallast box of aluzinc. Assembly rail of extruded aluminium. End caps of cast zinc.LouvreTerazza – louvre with aluminium enamelled cross blades.Luminaires can be supplemented with louvres at a later date.Refl ectorNarrow beam refl ector of spe-cular aluminium. The refl ectors are manufactured of MIRO with extremely good refl ective cha-racteristics. Fitted with end caps of aluzinc. The refl ector is easily attached to the luminaire using quick-action lock.MiscellaneousInternal cables are PVC-free. Induline complies with the Swe-dish Board of Electrical Safety's demands on limited external temperatures (90°) at rated voltage.

Wire respective chain suspensions for ceiling mounting.

Luminaire with bracket for wires or chains.


W kg Light dist.

FDH

Without louvre

1x28 2,2 A 32620

2x28 2,7 B 32623

1x35 2,6 A 32645

2x35 3,1 B 32648

1x49 2,6 A 32670

2x49 3,1 B 32673

1x54 2,2 A 32710

2x54 2,7 B 32713

Louvre Terazza

1x28 2,7 C 32626

2x28 3,4 D 32629

1x35 3,1 C 32651

2x35 4,2 D 32654

1x49 3,1 C 32676

2x49 4,3 D 32679

1x54 2,7 C 32716

2x54 3,4 D 32719

Induline Narrow beam

Accessories








179

182

181

180

1 2 3

4


1. All Induline bodies are balanced and consist of an assembly rail of extruded aluminium with end caps of cast zinc, and an assembly box. The refl ector and louvre are then fi tted, and together form an effective industrial luminaire.

2. In Induline we have positioned the T5-lamp in a type of trestle position. Material consumption is kept to a minimum and the weight is low. Internal cables are PVC-free in all T5-luminaires from Fagerhult.

3. Induline is a versatile luminaire, adapted for one of the market’s widest range of installation acces-sories. The picture shows Induline surface mounted.

4. Fagerhult always supplies Induline with sealed ends. This is to guarantee good axial cut-off without lowering the light quality and adaptation features.

Induline narrow beam

Induline medium beam

Induline wide beam

Induline

recessed

indu

stria

lpend

ant/su

rfac

e


A B C D E

W A B C

1x28 1192 86 1232x28 1192 133 1571x35 1492 86 1232x35 1492 133 1571x49 1492 86 1232x49 1492 133 1571x54 1192 86 1232x54 1192 133 157

AB

C

530

InstallationSurface mounted, wire catenary, conduit, chain and wire suspen-sion as well as lighting track.ConnectionOne Ø 21 mm cable entry fi tted with a blanking grommet at each end. Snap-in terminal block 5x2.5 mm2, placed in the centre with the possibility of through-wiring.DesignBallast box of aluzinc. Assembly rail of extruded aluminium. End caps of cast zinc.LouvreTerazza – louvre with aluminium enamelled cross blades.Beta – refl ector louvre with double parabolic cross blades in satin matt metallized aluminium. Luminaires can be supplemented with louvres at a later date.Refl ectorWide beam refl ector of specular aluminium. The refl ectors are manufactured of MIRO with extremely good refl ective cha-racteristics. Fitted with end caps of aluzinc. The refl ector is easily attached to the luminaire using quick-action lock.MiscellaneousInternal cables are PVC-free. Induline complies with the Swe-dish Board of Electrical Safety's demands on limited external temperatures (90°) at rated voltage.

Luminaire with adjustable wall bracket.

Luminaire with cantenary wire.


W kg Light dist.

FDH

Louvre Beta

1x28 2,2 C 32634

2x28 2,7 32740

1x35 2,6 C 32659

2x35 3,1 32742

1x49 2,6 C 32684

2x49 3,1 32743

1x54 2,2 C 32724

2x54 2,7 32741

Accessories









W kg Light dist.

FDH

Without louvre

1x28 1,9 A 32622

2x28 2,3 B 32730

1x35 2,2 A 32647

2x35 2,7 B 32731

1x49 2,2 A 32672

2x49 2,7 B 32688

1x54 1,9 A 32712

2x54 2,3 B 32733

Louvre Terazza

1x28 2,3 D 32628

2x28 2,9 E 32635

1x35 2,7 D 32653

2x35 3,4 E 32737

1x49 2,7 D 32678

2x49 3,4 E 32689

1x54 2,3 D 32718

2x54 2,9 E 32736

Induline Wide beam


Decorative end cap 1 lampEnd caps of white ABS plastic. Fitting Indulux wide beam.

Decorative end cap/pair 91710

Wire suspension

Single pendant with ceiling bracket.

L = 1,5 m, surface mounted with bracket/pair 91560

Sliding luminaire bracket

Luminaire bracket of natural fi nished aluzinc. Can be fi tted along the entire luminaire.

Sliding luminaire bracket/pair 91199

Adjustable ceiling bracketBracket of zinc coated 2,0 mm sheet steel. Height 72 mm.


Cable wire bracketMade of zinc coated sheet steel. Suitable for wire cable max Ø 10 mm.


Decorative end cap 2-3-lampsEnd caps of white ABS plastic. Fitting Indulux wide and medium beam.

Decorative end cap, wide beam/pair 91711Decorative end cap, medium beam/pair 91713

Chain suspensionSingle supensions for ceiling bracket for surface mounting or bracket for T-bars B=25 mm.

Chain supensionL=1 m incl. bracket/pair 91562

Conduit bracketMounting plate of zinc coated sheet steel equipped with hose clips for tubes Ø 45-65 mm. Hose clip can be replaced with those of another dimension


Adjustable wall bracketBracket of zinc coated 2,0 mm sheet steel. Length 235 mm.


Cable wire bracketMade of zinc coated sheet steel and suitable for luminaires with hole spacing c/c 35 mm.


InduluxAccessories

recessed

indu

stria

lpend

ant/su

rfac

e


A B

281

W A B C D

36 1300 225 150 128058 1600 225 150 1580

A

D

B

C

Ø23

Ø23 Ø23

InstallationSurface mounted, wire cable, tube, chain or wire suspension and lighting track.ConnectionFour access holes fi tted with blanking grommets - one Ø 23 mm at each end, two Ø 23 mm on top of the luminaire by each terminal block. 3-phase through-wiring 5x2.5 mm2. Snap-in terminal block 5x2.5 mm2 at each end.DesignBody and end caps of natural fi nished aluzinc, rotary lamp holders.LouvreProfal – profal louvre of alumini-um enamelled aluzinc sheet. The louvre remains attached to the body when opened. Luminaires can be retro-fi tted with a louvre.Refl ectorAsymmetrical. Specular anodised aluminium.Miscellaneous1- and 2-lamp luminaires with conventional ballast allows am-bient temperatures up to 45 °C.

Chain suspension with bracket 91562.

Luminaire with adjustable ceiling bracket 91374.

Indulux Asymmetrical


W kg Light dist.

FD

Without louvre

1x36 3,6 A 32480

1x58 4,8 A 32482

Profal louvre

1x36 4,0 B 32490

1x58 5,3 B 32492


W kg Light dist.

FD

Without louvre

1x36 3,6 A 32480-46

1x58 4,8 A 32482-46

Profal louvre

1x36 4,0 B 32490-46

1x58 5,3 B 32492-46

Accessories

Wire cable bracket fi ts wire max Ø 10 mm/pair 91196

Wire cable bracket for luminaire with hole dist. c/c 35/pair 91310


Chain susp. L=1,0 m, incl. ceiling bracket/pair 91562

Wire susp. L=1,5 m, incl. ceiling bracket/pair 91560




184

Indulux

The Indulux range consists of a wide assortment of

industrial luminaires that can also be used in many other

environments.

Many different bodies, refl ectors, louvres and

installation options make Indulux one of the market´s

most complete luminaire series for industrial buildings.

The body is manufactured of natural

aluzinc sheet. In industrial environments

aluzinc sheet gives up to six times better

corrosion resistance than hot-dipped gal-

vanised sheet. The refl ectors are produced

using specular anodised aluminium and

are avalable in four designs, that support

installation heights from approx. 2.5 to

17 m. The refl ector material has a refl ec-

tion factor of approx. 87%.

Indulux can be equipped for two diffe-

rent louvres: Profal – is ideal to all outputs

and refl ectors, alternatively Alfa – is only

suitable for wide beam luminaires. These

two louvres, in combination with the de-

corative end caps comply with the cut-off

requirements for normal visual demands.

The Indulux range is prepared for most

installation options, for example, surface

mounting, catenary wire, trunking, tube,

chain and wire suspension.

Wide beam with uplight

Wide beam

Medium beam

Narrow beam

Asymmetrical


185

185

186

187

188


A B C D E

279

W A B C D

1x36 1300 175 144 12802x36 1300 247 168 12801x58 1600 175 144 15802x58 1600 247 168 15803x58 1600 247 168 1580

A

D

B

C

Ø23

Ø23 Ø23

InstallationSurface mounted, wire cable, tube, chain or wire suspension and lighting track.ConnectionFour access holes fi tted with blanking grommets - one Ø 23 mm at each end, two Ø 23 mm on top of the luminaire by each terminal block. 3-phase through-wiring 5x2.5 mm2. Snap-in terminal block 5x2.5 mm2 at each end.DesignBody and end caps of natural fi nished aluzinc, rotary lamp holders.LouvreProfal – louvre of aluminium ena-melled aluzinc sheet. The louvre remains attached to the body when opened. Luminaires can be retro-fi tted with a louvre.Refl ectorMedium beam. Specular ano-dised aluminium. Can be fi tted with decorative, ABS plastic end caps.Miscellaneous1- and 2-lamp luminaires with conventional ballast allows am-bient temperatures up to 45 °C.

Sliding luminaire bracket 91199.

Seecuring the refl ector using the spring lock is quick and easy.

Indulux Medium beam


W kg Light dist.

FD

Without louvre

1x36 3,5 A 32440

2x36 4,1 B 32441

1x58 4,7 A 32442

2x58 5,8 B 32443

3x58 6,8 32444

Profal louvre

1x36 3,9 C 32450

2x36 4,7 D 32451

1x58 5,6 C 32452

2x58 6,5 D 32453

3x58 8,0 E 32454


W kg Light dist.

FD

Without louvre

1x36 3,5 A 32440-46

2x36 4,1 B 32441-46

1x58 4,7 A 32442-46

2x58 5,8 B 32443-46

3x58 6,8 32444-45

Profal louvre

1x36 3,9 C 32450-46

2x36 4,7 D 32451-46

1x58 5,6 C 32452-46

2x58 6,5 D 32453-46

3x58 8,0 E 32454-45

Accessories









Decorative end caps for 2-3 lamps/pair 91713


A B C D E

280

W A B C D

1x58 1600 246 165 15802x58 1600 328 183 15803x58 1600 328 183 1580

A

D

B

C

Ø23

Ø23 Ø23

InstallationSurface mounted, wire cable, tube, chain or wire suspension and lighting track.ConnectionFour access holes fi tted with blanking grommets - one Ø 23 mm at each end, two Ø 23 mm on top of the luminaire by each terminal block. 3-phase through-wiring 5x2.5 mm2. Snap-in terminal block 5x2.5 mm2 at each end.DesignBody and end caps of natural fi nished aluzinc, rotary lamp holders.LouvreProfal – louvre of aluminium ena-melled aluzinc sheet. The louvre remains attached to the body when opened. Luminaires can be retro-fi tted with a louvre.Refl ectorNarrow beam. Specular anodised aluminium.Miscellaneous1- and 2-lamp luminaires with conventional ballast allows am-bient temperatures up to 45 °C.

Luminaire with wire cable bracket 91196.

3-lamp luminaire.

Indulux Narrow beam


W kg Light dist.

FD

Without louvre

1x58 4,9 A 32462

2x58 6,1 B 32463

3x58 7,1 C 32464

Profal louvre

1x58 5,3 D 32472

2x58 6,8 E 32473

3x58 8,3 32474


W kg Light dist.

FD

Without louvre

1x58 4,9 A 32462-46

2x58 6,1 B 32463-46

3x58 7,1 C 32464-45

Profal louvre

1x58 5,3 D 32472-46

2x58 6,8 E 32473-46

3x58 8,3 32474-45

Accessories








Adjustable wall bracket/pair 91375recessed

indu

stria

lpend

ant/su

rfac

e


A B C D E

W A B C D

1x36 1300 150 140 12802x36 1300 205 157 12801x58 1600 150 140 15802x58 1600 205 157 15803x58 1600 205 157 1580

A

D

B

C

Ø23

Ø23 Ø23

InstallationSurface mounted, wire cable, tube, chain or wire suspension and lighting track.ConnectionFour access holes fi tted with blanking grommets - one Ø 23 mm at each end, two Ø 23 mm on top of the luminaire by each terminal block. 3-phase through-wiring 5x2.5 mm2. Snap-in terminal block 5x2.5 mm2 at each end.DesignBody and end caps of natural fi nished aluzinc, rotary lamp holders.LouvreProfal – louvre of aluminium enamelled aluzinc sheet.Alfa – louvre with V shaped length and cross-blades of anodised aluminium. The louvre remains attached to the body when opened. Luminaires can be retro-fi tted with a louvre.Refl ectorWide beam. Specular anodised aluminium. Can be fi tted with decorative, ABS plastic end caps.Miscellaneous1- and 2-lamp luminaires with conventional ballast allows am-bient temperatures up to 45 °C.

Twin lamp with Profal louvre installed on a tube with tube bracket 91198 for tubes Ø 45-65 mm.

Indulux uplight mounting with cable wire bracket 91196.

Indulux Wide beam

Luminaire direct Conv. HF-stdW kg Light dist.

FD

Without louvre

1x36 3,5 32400 32400-46

2x36 4,1 A 32401 32401-46

1x58 4,7 32402 32402-46

2x58 5,8 A 32403 32403-46

3x58 6,8 32404 32404-45

With Profal louvre

1x36 3,9 32410 32410-46

2x36 4,7 B 32411 32411-46

1x58 5,6 32412 32412-46

2x58 6,5 B 32413 32413-46

3x58 8,0 32414 32414-45

With Alfa louvre

2x36 4,6 C 32551 32551-46

2x58 6,4 C 32553 32553-46

Luminaire Direct/Indirect Conv. HF-std

W kg Light dist.

FD

Without louvre

2x36 4,1 32421 32421-46

2x58 5,8 32423 32423-46

3x58 6,8 32424 32424-45

With Profal louvre

2x36 4,7 D 32431 32431-46

2x58 6,5 D 32433 32433-46

3x58 8,0 32434 32434-45

With Alfa louvre

2x36 4,6 E 32561 32561-46

2x58 6,4 E 32563 32563-46

Accessories









Decorative end caps for 2-3 lamps/pair 91711

Decorative end caps for 1-lamps/pair 91710

recessed

indu

stria

lpend

ant/su

rfac

e


A A + Refl ector B B + Refl ector

W A B C D

FD1x18 673 113 99 4502x18 673 170 103 4501x36 1283 113 99 6602x36 1283 170 103 6601x58 1583 113 99 9002x58 1583 170 103 900

FDH1x28 1283 113 99 6602x28 1283 170 103 6601x35/49 1583 113 99 9002x35/49 1583 170 103 900

D

AB

C

InstallationSurface mounted, wall, cablewire or wall bracket.ConnectionTwo Ø 22 mm cable entry fi tted with blanking grommet at each end. Terminal block 5x2.5 mm2 with 3-phase through-wiring at each end. The 18W luminaire with terminal block 3x2.5 mm2 in the end. Easy installation by snapping the assembly plate onto the body.DesignBody of polycarbonate. Assembly plate of white enamelled sheet steel.LouvreCover of acrylic plastic or poly-carbonate. The cover is easily snapped onto the body. It can remain attached to the body when relamping.MiscellaneousRefl ector of specular anodised aluminium offered as an ac-cessorie. The luminaire is made of recycled material – body of PC and cover of PMMA or PC. Construction with snap-in cover and assembly plate increases the number of components in the luminair which economise on material, energy and the environment. The luminaire complies with the Swedish Board of Electrical Safety´s demands on limited external temperatures (90°) at rated voltage.

Kaptur 2000


W kg Light dist. Acrylic cover PC cover

FD

1x18 1,5 A 35101 35110

2x18 1,8 B 35102 35111

1x36 2,1 A 35103 35112

2x36 3,0 B 35104 35113

1x58 3,0 A 35105 35114

2x58 4,9 B 35106 35115


W kg Light dist. Acrylic cover PC cover

FD

1x18 1,5 A 35101-44 35110-44

2x18 1,8 B 35102-44 35111-44

1x36 2,1 A 35103-45 35112-45

2x36 3,0 B 35104-45 35113-45

1x58 3,0 A 35105-45 35114-45

2x58 4,9 B 35106-45 35115-45

FDH

1x28 2,0 35120 35130

2x28 2,8 35121 35131

1x35 2,2 35122 35132

2x35 3,4 35123 35133

1x49 2,2 35124 35134

2x49 3,4 35125 35135

Accessories







Spare covers

Acrylic PC







The cover is easily snapped into position.

Quick and easy installation by snapping the assembly plate onto the body.

recessed

indu

stria

lpend

ant/su

rfac

e


A B C D

W A1 A2 B1 B2 C

"300"28 1199 1171 299 269 8935 1499 1471 299 269 89

"600"14 599 571 599 569 8928 1199 1171 599 569 89

Ø19Ø19

C

++

A2

A1B1

B2

W A B C D

28 1203 303 89 110035 1503 303 89 1400

Ø19+

D

AB

C

Multilume Hydro Beta

Luminaire

W kg Light dist. Arm. modul

FDH

Recessed IP 65/50

3x14 9,1 600 x 600 23040

4x14 9,2 A 600 x 600 23041

2x28 9,4 B 300 x 1200 23042

2x28 13,9 600 x 1200 23044

3x28 14,3 C 600 x 1200 23045

4x28 14,5 D 600 x 1200 23046

2x35 11,7 B 300 x 1500 23043

Surface mounting IP 55

2x28 9,7 B 23047

2x35 12,1 B 23048

Accessories

Glass frame suction pad 94295

InstallationFor recessed or surface mounting. The recessed model is suitable for fi xed suspended ceilings or suspended ceilings with visible T-bars. Requisite suspension fi t-tings supplied. Ceiling thickness from 20 to 46 mm.Connection Cable entry on the top fi tted with a blanking grommet. 5-way snap-in terminal block.DesignLuminaire body of white enamel-led and anti-corrosive treated aluzinc. Louvre frame of extruded aluminium fi tted with toughened protective glass. Seal between the frame and protective glass as well as between the frame and body.LouvreBeta – double parabolic refl ector louvre of satin matt metallised aluminium integrated into a single unit. Louvre made using MIRO with extremely good refl ec-tion properties. The louvre is earthed and remains attached to the body when opened. Mounted in the body by means of spring clips. As an option Hydro is avai-lable with an opal acrylic diffuser or louvre Gamma.Refl ectorThe luminaire body is fi tted with a top refl ector, one for each lamp.MiscellaneousThe louvre frame has no screws for fastening. The luminaire has been designed with a minimum of dirt collecting surfaces, which facilitates cleaning. When dis-mantling a glass frame suction pad is recommended. Enclosure class IP 65 under suspended ceilings and IP 50 above suspen-ded ceilings. Can be equipped with HF-ballast for dimming (1-10V, DSI, DALI).

The louvre module is secured using internal spring clips. The module is pushed up from below into its natural position. A glass frame suction pad is recommended when dismantling.

Multilume Hydro for surface mounting.

Multilume Hydro has a detachable louvre module held in place by high tension spring clips. Mantling and dismantling of louvre module for maintenance requires some force, so where luminaires are placed with a suspended ceiling system it is recommended that additional support bar support hangers are included.

recessed

indu

stria

lpend

ant/su

rfac

e


A CB DA + lamell

800

1200295

101

Scatola


W kg Light dist.

FDH

Wide beam

2x28 8,4 A 35180

2x54 8,4 A 35181

Medium beam

2x28 8,4 B 35183

2x54 8,4 B 35184

Asymmetrical

2x28 8,4 D 35186

2x54 8,7 D 35187

Beta louvre

2x28 9,2 C 35188

2x54 9,2 C 35189

Accessories

Lamell louvre 95964

Cable wire bracket, acidproof/pair 91997

Adjustable ceiling bracket, acidproof/pair 91996

Adjustable wall bracket, acidproof/pair 91738

InstallationSurface mounted, wire and bracket.ConnectionSnap-in terminal block 5x2.5 mm2 at each end with through-wiring 5x2.5 mm2. Two Ø 23 mm cable entries fi tted with blanking grom-mets at each end.DesignBody of acidproof steel. Folding and lockable protective sheet of toug-hened glass. Sealing strip of EPDM rubber between the glass and body.LouvreBeta – double parabolic refl ector louvre with side and cross blades of satin matt metallized aluminium integrated into a single unit. The refl ector louvre is manufactured of MIRO, which has excellent refl ection properties. Lamell – louvre with aluminium enamelled cross blades as accessories to wide, medium and asymmetrical light distributions.Both louvres remain attached when opened. Earthed.Refl ectorWide-, medium beam or asymme-trical refl ector of specular anodised aluminium.MiscellaneousScatola IP 65 is unsuitable for use in environments where the protective glass can be exposed to scratches or blasting. If the hardened surface lay-er of the glass is damaged the glass can splinter. Tempered laminated glass is available as an accessory. The luminaire complies with the Swedish Board of Electrical Safety's demands on limited external tem-peratures (90°) at rated voltage.

Scatola IP 65 is retained with a safety wire.

Scatola IP 65 is available with a cross blade louvre as an accessory.

AllFive Clear - ESIcms.esi.info/Media/documents/Fager_industrial_ML.pdf · 196 • A B B + Reﬂ...

Documents

Transcript of AllFive Clear - ESIcms.esi.info/Media/documents/Fager_industrial_ML.pdf · 196 • A B B + Reﬂ...