All part features should be unsuppressed when releasing (making the final version) the part.
description
Transcript of All part features should be unsuppressed when releasing (making the final version) the part.
![Page 1: All part features should be unsuppressed when releasing (making the final version) the part.](https://reader036.fdocuments.us/reader036/viewer/2022081513/56815cab550346895dcaabac/html5/thumbnails/1.jpg)
1
All part features should be unsuppressed when releasing (making the final version) the part.
Part must have material property and color assigned
Part must not be in roll-back mode
Features and sketches must be named
All sketched must be fully defined
Use mm, N, s, K units (important for analysis)
Zoom to fit and position in isometric view (or other meaningful view) before saving
PARTS
![Page 2: All part features should be unsuppressed when releasing (making the final version) the part.](https://reader036.fdocuments.us/reader036/viewer/2022081513/56815cab550346895dcaabac/html5/thumbnails/2.jpg)
2
ASSEMBLIES
Assembly of 3D solid modeling software in general does not
contain “assembly” geometry. The assembly contains
components (i.e. parts and lower level assemblies) assembled
together in the intended manner.
Assembly contains information on where to find parts and how
are parts oriented relative to each other (mated).
The only features that can be defined in assembly are “negative”
features (cut)
![Page 3: All part features should be unsuppressed when releasing (making the final version) the part.](https://reader036.fdocuments.us/reader036/viewer/2022081513/56815cab550346895dcaabac/html5/thumbnails/3.jpg)
3
ASSEMBLIES
When retrieving the assembly (opening assembly file), CAD program needs the following information:
- BOM (Bill of Material) structure: This information is stored within assembly file and is used to retrieve all listed components. It is obvious, that the system has to be able to “see” and retrieve all components regardless where they reside on the network.
- “Mating” information: How feature surfaces of individual components are assembled - mated to their parent components.
- Feature information: Assembly cuts (in case they have been created) and parts/features that are being intersected by them.
![Page 4: All part features should be unsuppressed when releasing (making the final version) the part.](https://reader036.fdocuments.us/reader036/viewer/2022081513/56815cab550346895dcaabac/html5/thumbnails/4.jpg)
4
ASSEMBLIES
BOM
MATING INFO
ASSEMBLY FEATURE (CUT)
shear pin.sldasm
![Page 5: All part features should be unsuppressed when releasing (making the final version) the part.](https://reader036.fdocuments.us/reader036/viewer/2022081513/56815cab550346895dcaabac/html5/thumbnails/5.jpg)
5
ASSEMBLIES
An assembly structure can have as many lower assembly levels as needed. They should reflect the logical structure of the designed product.
four plates and bar.sldasm
![Page 6: All part features should be unsuppressed when releasing (making the final version) the part.](https://reader036.fdocuments.us/reader036/viewer/2022081513/56815cab550346895dcaabac/html5/thumbnails/6.jpg)
6two gears.sldasm
ASSEMBLIES
Collision detection and physical dynamics
![Page 7: All part features should be unsuppressed when releasing (making the final version) the part.](https://reader036.fdocuments.us/reader036/viewer/2022081513/56815cab550346895dcaabac/html5/thumbnails/7.jpg)
7
ASSEMBLIES
Crank shaft assembly
![Page 8: All part features should be unsuppressed when releasing (making the final version) the part.](https://reader036.fdocuments.us/reader036/viewer/2022081513/56815cab550346895dcaabac/html5/thumbnails/8.jpg)
8
ASSEMBLIES
Elliptic trammel
![Page 9: All part features should be unsuppressed when releasing (making the final version) the part.](https://reader036.fdocuments.us/reader036/viewer/2022081513/56815cab550346895dcaabac/html5/thumbnails/9.jpg)
9
FILE MANAGEMENT
Be careful moving assembly files, do not destroy relations between assembly and components.
Use “Pack and Go” feature to keep relations while moving files
![Page 10: All part features should be unsuppressed when releasing (making the final version) the part.](https://reader036.fdocuments.us/reader036/viewer/2022081513/56815cab550346895dcaabac/html5/thumbnails/10.jpg)
10
FILE MANAGEMENT
This message will give you 0 for your assignment mark
![Page 11: All part features should be unsuppressed when releasing (making the final version) the part.](https://reader036.fdocuments.us/reader036/viewer/2022081513/56815cab550346895dcaabac/html5/thumbnails/11.jpg)
11
EXPLODED VIEWS
Learn to use exploded views
Oldham coupling.SLDASM
![Page 12: All part features should be unsuppressed when releasing (making the final version) the part.](https://reader036.fdocuments.us/reader036/viewer/2022081513/56815cab550346895dcaabac/html5/thumbnails/12.jpg)
12
SECTION VIEWS
Learn to use section views (in parts and assemblies)
shear pin. sldasm
![Page 13: All part features should be unsuppressed when releasing (making the final version) the part.](https://reader036.fdocuments.us/reader036/viewer/2022081513/56815cab550346895dcaabac/html5/thumbnails/13.jpg)
13
WORKING WITH IMPORTED GEOMETRY
![Page 14: All part features should be unsuppressed when releasing (making the final version) the part.](https://reader036.fdocuments.us/reader036/viewer/2022081513/56815cab550346895dcaabac/html5/thumbnails/14.jpg)
14
WORKING WITH IMPORTED GEOMETRY
![Page 15: All part features should be unsuppressed when releasing (making the final version) the part.](https://reader036.fdocuments.us/reader036/viewer/2022081513/56815cab550346895dcaabac/html5/thumbnails/15.jpg)
15
Views using first angle projection;
used in Europe.
Views using third angle projection;
used in North America
DRAWINGS
![Page 16: All part features should be unsuppressed when releasing (making the final version) the part.](https://reader036.fdocuments.us/reader036/viewer/2022081513/56815cab550346895dcaabac/html5/thumbnails/16.jpg)
16Customary views using third angle projectionbracket 01.sldprt
DRAWINGS
![Page 17: All part features should be unsuppressed when releasing (making the final version) the part.](https://reader036.fdocuments.us/reader036/viewer/2022081513/56815cab550346895dcaabac/html5/thumbnails/17.jpg)
17Customary views using first angle projection
DRAWINGS
![Page 18: All part features should be unsuppressed when releasing (making the final version) the part.](https://reader036.fdocuments.us/reader036/viewer/2022081513/56815cab550346895dcaabac/html5/thumbnails/18.jpg)
18Automatic dimensions are most often not acceptable
DRAWINGS
![Page 19: All part features should be unsuppressed when releasing (making the final version) the part.](https://reader036.fdocuments.us/reader036/viewer/2022081513/56815cab550346895dcaabac/html5/thumbnails/19.jpg)
19
Dimensions must either modified or created
DRAWINGS
![Page 20: All part features should be unsuppressed when releasing (making the final version) the part.](https://reader036.fdocuments.us/reader036/viewer/2022081513/56815cab550346895dcaabac/html5/thumbnails/20.jpg)
20
DRAWINGS
BOM
TOC
![Page 21: All part features should be unsuppressed when releasing (making the final version) the part.](https://reader036.fdocuments.us/reader036/viewer/2022081513/56815cab550346895dcaabac/html5/thumbnails/21.jpg)
21
DRAWINGS
Learn to use all types of views in drawings
Learn BOM
Learn TOC
Learn dimensioning
…
…
Learn fits and GD&T; we’ll cover this later in the course
![Page 22: All part features should be unsuppressed when releasing (making the final version) the part.](https://reader036.fdocuments.us/reader036/viewer/2022081513/56815cab550346895dcaabac/html5/thumbnails/22.jpg)
22
ON LINE MODELS
Great site for selection design
http://www.3dcontentcentral.com/
![Page 23: All part features should be unsuppressed when releasing (making the final version) the part.](https://reader036.fdocuments.us/reader036/viewer/2022081513/56815cab550346895dcaabac/html5/thumbnails/23.jpg)
23http://www.3dcontentcentral.com/3DContentCentral/
ON LINE MODELS
![Page 24: All part features should be unsuppressed when releasing (making the final version) the part.](https://reader036.fdocuments.us/reader036/viewer/2022081513/56815cab550346895dcaabac/html5/thumbnails/24.jpg)
24
ON LINE RESOURCES
![Page 25: All part features should be unsuppressed when releasing (making the final version) the part.](https://reader036.fdocuments.us/reader036/viewer/2022081513/56815cab550346895dcaabac/html5/thumbnails/25.jpg)
25http://www.solidworks.com/
ON LINE RESOURCES