AII33093 2007 Pilot XM Radio System (EX) · Illustration of the XM Satellite Radio Installed on the...

© 2006 American Honda Motor Co., Inc. - All Rights Reserved. All 33093 (0608) 1 of 12

INSTALLATIONINSTRUCTIONS

Accessory Application Publications No.

Issue Date

08B15-S9V-1A00-91

PARTS LIST

XM Radio Attachment (sold separately)P/N 08B15-S9V-100A

2 Tuner brackets

4 Flange bolts, 6 x 12 mm

2 Cushion tapes

BUS cable

4 Washer-screws, 5 x 8 mm

EPT sealer(not used)

18 Wire ties

Wire tie with clip

Pillar clip

AUG 20062007 PILOTXM SATELLITE RADIO SYSTEM

(EX)

XM Antenna (sold separately)P/N 08A15-0J1-100

Antenna

All 33093

XM Unit (sold separately)P/N 08A15-3J1-000

XM tuner

2 of 12 All 33093 (0608) © 2006 American Honda Motor Co., Inc. - All Rights Reserved.

TOOL AND SUPPLIES REQUIRED#2 Phillips screwdriverFlat-tip screwdriverUtility knifeTape measureShop towelScissorsRatchet10 mm and 14 mm Socket10 mm and 14 mm Combination wrenchesFelt-tip penIsopropyl alcohol(Isopropyl alcohol, in a 60/40 solution with water)T25 TORX bit

Illustration of the XM Satellite Radio Installed onthe Vehicle

INSTALLATION

Customer Information: The information in thisinstallation instruction is intended for use only byskilled technicians who have the proper tools,equipment, and training to correctly and safely addequipment to your vehicle. These proceduresshould not be attempted by “do-it-yourselfers.”

1. Make sure you have the anti-theft code for theradio, then write down the frequencies for thepreset buttons.

2. Disconnect the negative cable from the battery.

3. Remove the cap from the right sun visor (fourretaining tabs).

ANTENNACONNECTOR

RIGHT SUNVISOR

TORX SCREW

CAP

RETAININGTABS (4)

4. Remove the right sunvisor (two TORX screws andunplug the connector).

AUDIOUNIT

BUSCABLE

ANTENNAHARNESS

XM TUNER

5412070B

6512010Y


DOORWEATHERSTRIP(Remove.)

CLIP

RIGHT FRONTPILLAR TRIM

GLOVE BOX

STOPS (2)

(Lowercompletely.)

5. Remove two caps from the right front grab rail andremove the grab rail (two screws).

7. Remove the door weatherstrip from the openingedge of the right front door in the area shown,then remove the right front pillar trim (one clip).

8. Lower the glove box by removing the right and leftstops.

COVER

BOLT

COVER

RIGHT FRONTPILLAR


CLIP

PIN

CLIP

PART MARKED WITH“SIDE CURTAIN AIRBAG”

Strike.

SHOPTOWEL

RUBBERMALLET

6. Pull away the door weatherstrip from around theright front pillar trim. Using a small rubber mallet,and a shop towel, gently tap the right quarterpillar trim at the area marked “SIDE CURTAINAIRBAG” to release the clip.

DOORWEATHERSTRIP

4N23033B

4N23041B

5412080B

4N23060B


AUDIO UNIT

VEHICLECONNECTOR

SCREW(Reuse.)

VEHICLEANTENNACONNECTOR

12. Remove the audio unit (four screws), pull the audiounit out toward you, unplug the vehicle connectorsand vehicle antenna connector.

METER PANEL

SELF-TAPPINGSCREW

CLIPS (2)

9. Remove the meter panel (two self-tapping screwsand two clips).

METER SUBPANEL

CLIPS (3)

10. Remove the meter sub panel (three clips).

VEHICLECONNECTOR

CLIPS (5)

AUDIO PANEL

11. Gently pull out on the left side of the audio panelto release the two clips, then pull out to releasethe remaining three clips. Unplug the vehicleconnectors and remove the audio panel.

5412041B

4N23071B

5601020Y4N23080B


DRIVER’S CENTERCONSOLE TRIM

PASSENGER’S CENTERCONSOLE TRIM

CLIPS (3)RIGHTVEHICLEBRACKET

SCREW

HEATERCONTROL UNIT

POCKET

LEFTVEHICLEBRACKET

SELF-TAPPINGSCREW

CENTER PANEL

CLIPS(2)

VEHICLECONNECTOR

VEHICLE 30-PINCONNECTOR


With Player

• Remove the driver’s and passenger’s centerconsole trim pieces (three clips each). Takecare not to damage the clips.

• Remove four self-tapping screws that fasten thecenter panel.

• Pull the center panel out toward you to releasethe two clips. Unplug the vehicle connectorfrom the accessory socket, and remove thecenter panel.

• Remove four screws that fasten the left andright vehicle brackets. Pull the heater controlunit and pocket out toward you, and unplug thevehicle connectors.

13. Remove the driver’s seat front cover from thedriver’s seat (four clips).

CLIPS (4)

DRIVER’S SEATFRONT COVER

DRIVER’SSEAT

4N23100B


ADHESIVEBACKING

5 mm

30 mm

ATTACHAREA

HEADLINER

ATTACHAREA

FRONTWINDOW

ANTENNA

HEADLINER

17. Using isopropyl alcohol, clean the windshieldwhere the antenna will attach. Remove theadhesive backings from the antenna and attachthe antenna to the front window at the locationshown. Install the antenna by applying sufficientpressure.

DRIVER’S SEATREAR COVER

CLIPS (4)

DRIVER’S SEAT

DRIVER’S SEAT

BOLTS (4)

14. Remove the driver’s seat rear cover from thedriver’s seat. Take care not to damage the clips.

15. Remove the four bolts that secure the driver’s seatside rails to the floor.

16. Remove the driver’s center console lower cover(seven clips). Take care not to damage the clips.

CLIPS (7)DRIVER’S CENTERCONSOLE LOWERCOVER

DRIVER’SSEAT

4N23110B

4N23120B

4N23090B

4N24010B


GLOVE BOXOPENING

ANTENNAHARNESS

VEHICLEHARNESS

WIRE TIES (4)

VEHICLEHARNESS

ANTENNAHARNESS

VEHICLEHARNESS

WIRE TIEAUDIO UNITOPENING

19. Route the antenna harness through the glove boxopening and route it along the vehicle harness.Secure the antenna harness to the vehicleharness with four wire ties.

20. Route the antenna harness to the audio unitopening and secure it to the vehicle harness withone wire tie.

RIGHT FRONTPILLAR

RIGHT FRONTPILLAR TRIMOPENING

ANTENNA

ANTENNAHARNESS

VEHICLEHARNESS

VEHICLECLIPS (4)

WIRE TIES (5)

HEADLINER

18. Route the antenna harness along the right frontpillar and through the right front pillar trimopening. Secure the antenna harness to thevehicle harness with five wire ties.

ANTENNAHARNESS

BUSCABLE

AUDIO UNITOPENING

BUS CABLE14-PINCONNECTOR VEHICLE 20-PIN

CONNECTOR

WIRETIE

VEHICLEHARNESS

21. Continue routing the antenna harness and one endof the BUS cable through the radio opening anddown along the vehicle harness. Align the otherend of the BUS cable with the vehicle 20-pinconnector. Then secure the antenna harness andBUS cable to the vehicle harness with one wiretie.

4N24021B

4N24030B

4N24040B

4N24050B


DRIVER’S CENTERCONSOLE LOWERCOVER OPENING

BUSCABLE

ANTENNAHARNESS

VEHICLEHARNESS

VEHICLEFRAME

BUSCABLE ANTENNA

HARNESS

WIRETIE

VEHICLEHARNESS

WIRETIE

22. Route the antenna harness and BUS cable alongthe vehicle harness toward the floor, of the lowercenter console, and pull them out from under thedriver’s center console lower cover.

23. Secure the antenna harness and BUS cable to thevehicle harness and to the vehicle frame with twowire ties.

LOWERCENTERCONSOLE

With Player

• Bundle the BUS cable with one wire tie asshown.

• Route the antenna harness along the vehicleframe .

• Pull the BUS cable out 100 mm from thevehicle wire tie through the heater control unitopening.

• Secure the BUS cable to the vehicle harnessusing one wire tie.

WIRETIE

VEHICLEFRAME

ANTENNAHARNESS

BUSCABLE

WIRETIE

BUSCABLE

150 mm

100 mm

VEHICLEHARNESS

100 mm

VEHICLEWIRE TIE

HEATERCONTROL UNITOPENING

5725110Y

5725100Y

4N25010B

4N25021B


• Secure the antenna harness and BUS cable tothe vehicle frame with three ties in the areas.

• Connect the bus cable 14-pin connector to theplayer.

Cassette Player

MP3 Player

VEHICLEFRAME

WIRETIE

BUSCABLE

ANTENNAHARNESS

HEATERCONTROLUNIT

BUSCABLE

BUSCABLE 14-PINCONNECTOR

CASSETTEPLAYER

BUSCABLE 14-PINCONNECTOR

BUSCABLE

HEATERCONTROLUNIT

MP3PLAYER

RIGHTPLAYERBRACKET

SCREW(reused.)

HEATERCONTROLUNIT

LEFTPLAYERBRACKET

BUSCABLE


WASHER-SCREW(reused.)

WASHER-SCREW(reused.)


• Remove the two washer-screws from thedashboard.

5725130Y

5725140Y

5725120Y

5426161Y


VEHICLEHARNESS

FLOOR CARPET

Slit

50 mm

FLOORCARPET

BUSCABLE

ANTENNAHARNESS

27. Measure and slit the driver’s floor carpet areashown. Route the antenna harness and BUS cableunder the floor carpet and out through the slit.Take care not damage to the antenna harness andBUS cable when cutting the floor mat.

VEHICLEFRAME

CUSHION TAPE(Cut in half.)

VEHICLEHARNESS

VEHICLEFRAME

BUSCABLE

ANTENNAHARNESS

26. Using isopropyl alcohol on a shop towel, clean thevehicle frame where the cushion tapes will attach.Cut a cushion tape in half and attach the twohalves of the cushion tape to the vehicle framecleaned with isopropyl alcohol.

AUDIO UNIT

SCREW(Reuse.)

25. Reinstall the audio unit with four screws (youremoved).

AUDIOUNIT AUDIO UNIT

OPENING

BUS CABLE14-PINCONNECTOR

VEHICLECONNECTOR

VEHICLEANTENNACONNECTOR

24. Plug the BUS cable 14-pin connector, vehicleconnectors and vehicle antenna connector intothe audio unit, then carefully slide the audio unitinto the audio unit opening.

CUSHION TAPE(Clean withisopropyl alcohol(in a 60/40 solutionwith water)

4N25040B

4N25051B4N25030B

4N25061B


6512031Y

6512050Y

6512040Y6512020Y

TUNERBRACKET

5 x 8 mmWASHER-SCREWXM TUNER

28. Attach the tuner brackets to the XM tuner with four5 x 8 mm washer screws.

29. Using isopropyl alcohol, clean the area where thecushion tape will attach. Attach the cushion tapeto the tuner bracket at the location shown.

6 x 12 mmFLANGEBOLTS (4)

DRIVER’SSEAT

SEAT RAIL

TUNERBRACKET

TUNERBRACKET

XM TUNER

5 x 8 mmWASHER-SCREW

18 mm

FRONT

TUNERBRACKETcenter.

CUSHION TAPE

30. Install the tuner bracket to the driver’s seat railswith the four 6 x 12 mm flange bolts. Tighten thebolts securely.

XM TUNER

FRONTTUNERBRACKET

WIRE TIEWITH CLIP

BUSCABLE

FRONT

XM TUNER

BUS CABLE14-PINCONNECTOR

ANTENNACONNECTOR

31. Plug the BUS cable 14-pin connector into the XMtuner 14-pin connector.

32. Plug the antenna connector into the XM tunerantenna connector.

33. Secure the BUS cable and the antenna harness tothe tuner bracket with one wire tie with clip.

34. Secure the BUS cable and the antenna harnesswith one tie wire.

XM TUNER 14-PINCONNECTOR

XM TUNERANTENNACONNECTOR

ANTENNAHARNESS

WIRETIE

BUSCABLE

ANTENNAHARNESS


4N23050B

41. To install the pillar clip, position it at right anglesto the right front pillar and install by lightlypushing on the area marked with “SIDECURTAIN AIRBAG” on the right front pillar trim.Check that the pillar clip is not interfering with theairbag. Take care not to push the right front pillartrim excessively.

42. Reinstall all removed parts.

43. Reconnect the negative cable to the battery.

44. Enter the customer’s radio anti-theft code, andreset the radio station presets.

45. Reset the clock.

NOTE: Whenever the battery is disconnected, thedriver’s AUTO function is disabled.

46. Start the engine. Push down on the driver’swindow switch until the window is fully open.

47. Pull up on the driver’s window switch to close thewindow completely, then hold the switch for asecond or 2 more.

48. Test the AUTO window function.


NEWPILLARCLIP

CLIP(Discard.)


35. Bundle the excess of the antenna harness.Secure the antenna harness to the vehicle’sharness using two wire ties.

ANTENNA HARNESS(Bundle the excess)

36. Bundle the excess of the BUS cable. Secure theBUS cable and the antenna harness to thevehicle’s harness.

5610010P

BUS CABLE(Bundle theexcess.)

WIRETIE

WIRETIE

37. Check that all wire harnesses are routed properlyand all connectors are plugged in.

38. Reinstall the driver’s center console lower cover.

39. Reinstall the driver’s seat. Take care not to pinchthe any wires. Torque the seat bolts to 47 N·m(35 lb·ft).

40. Remove the clip from the top of the right frontpillar trim, and install a new pillar clip.

AII33093 2007 Pilot XM Radio System (EX) · Illustration of the XM Satellite Radio Installed on the...

Documents

Transcript of AII33093 2007 Pilot XM Radio System (EX) · Illustration of the XM Satellite Radio Installed on the...