AII32459-34084 07 Ridgeline xm radio - College Hills · PDF file2 of 11 AII 32459-34084 (0802)...

© 2008 American Honda Motor Co., Inc. - All Rights Reserved. AII 36647-38808 (0802) 1 of 11

INSTALLATIONINSTRUCTIONS

Accessory .oN snoitacilbuPnoitacilppA

Issue Date

FEB 2008

2008 RIDGELINEXM RADIO SYSTEMAII 36647-38808

08B15-SJC-1A00-91

PARTS LIST

Attachment Kit:P/N 08B15-SJC-100A

2 XM tuner bracket

Bus cable

Wire tie with clip

21 Wire ties

3 EPT sealers

Cushion tape

4 Flange nuts, 6 mm

4 Washer-screws, 5 x 8 mm

4 Washer-bolts, 6 x 16 mm

XM Antenna (sold separately):P/N 08A15-0J1-100

Antenna

XM Tuner (sold separately):P/N 08A15-3J1-000

XM tuner

TOOLS AND SUPPLIES REQUIREDPhillips screwdriverFlat-tip screwdriver10 mm Combination wrenchRatchet8 and 10 mm SocketIsopropyl alcoholShop towelTape measureScissorsFelt-tip penTORX wrench

www.collegehillshonda.com

2 of 11 ©)2080( 48043-95423 IIA 2008 American Honda Motor Co., Inc. - All Rights Reserved.

4703032T

4703023T

6421180B 4. Pull away the weatherstrip from aroundpassenger’s A-pillar. Remove the passenger’s A-pillar trim (two clips).

Illustration of the XM Radio Installed on theVehicle

Customer Information: The information in thisinstallation instruction is intended for use only byskilled technicians who have the proper tools,equipment, and training to correctly and safely addequipment to your vehicle. These proceduresshould not be attempted by “do-it-yourselfers.”

INSTALLATION

1. Make sure you have the anti-theft code for theradio, then write down the radio station presets.

2. Disconnect the negative cable from the battery.

ANTENNA

XM TUNER

BUSCABLE

AUDIOUNIT

3. Remove the passenger’s front grab rail:

• Remove the screw covers (two retaining tabsfor each cover).

• Remove the two screws, and remove thepassenger’s grab rail.

PASSENGER’SGRAB RAIL

SCREWCOVER

SCREW

RETAININGTAB

RETAININGTAB

SCREWSCREWCOVER

WEATHERSTRIP(Pull away.)

2 CLIPS PASSENGER’SA-PILLAR TRIM



4703231T

3915102T

3916011T

5. Remove the right sunvisor screw cover (fourretaining tabs), and remove the right sunvisor(two TORX screws, and unplug the vehicleconnector).

6. Open the glove box. Remove the left and rightstops from the glove box by releasing the retainingtabs.

7. Remove the left dashboard side cover (sevenclips).

8. Insert a flat-tip screwdriver wrapped with a shoptowel into the groove of the instrument panel andrelease the two clips. Pull the instrument panel outtoward you to release the eighteen clips, andremove the instrument panel by unplugging thevehicle connectors.

4703051T

RIGHTSUNVISOR

TORX SCREWS(T25)

SCREWCOVER

4 RETAININGTABS

VEHICLE 2-PINCONNECTOR

LEFTDASHBOARDSIDE COVER

2 STOPS

2 RETAININGTABS

RIGHTSTOPPERLEFT

STOPPER

GLOVE BOX

GLOVE BOX

VEHICLECONNECTORS

VEHICLECONNECTORS

INSTRUMENTPANEL

18 CLIPS

VEHICLECONNECTOR SHOP

TOWEL

FLAT-TIP SCREWDRIVERS(Insert into the groove.)

2 CLIPS

7 CLIPS



3916042T

3916021T

4606030T

9. Remove the meter assembly (four self-tappingscrews, and unplug the three vehicle connectors).

11. Remove the driver’s dashboard under cover:

• Remove the one self-tapping screw.

• Release the nine clips, and pull out on thedriver’s dashboard under cover.

• Unplug the vehicle connectors, and removethe vehicle tube. Remove the driver’sdashboard under cover.

12. Remove the fuel fill door release handle. Removethe left front door sill trim (three clips and threeretaining tabs).

AUDIOUNIT

5 BOLTS

INSTRUMENTPANELVEHICLE

CONNECTORS DRIVER’S DASHBOARDUNDER COVER

9 CLIPS

SELF-TAPPINGSCREW

VEHICLECONNECTOR

VEHICLETUBE

VEHICLE CONNECTOR(If equipped.)

10. Remove the audio unit (five bolts, pull the audiounit out towards you, and unplug the vehicleconnectors).

4703042T

SELF-TAPPINGSCREWS

METERASSEMBLY

VEHICLECONNECTORS

RETAININGTABS

RETAINING TABLEFT FRONTDOOR SILL TRIM

CLIP

FRONT

FUEL FILL DOORRELEASE HANDLE

CLIP



4703062T

3916050T

14. Remove the driver’s seat frame rear cover (twoclips and two hooks).

4713010K

DRIVER’SSEAT

DRIVER’S SEAT FRAMEREAR COVER

2 CLIPS

2 HOOKS

Installing the Antenna

15. Using isopropyl alcohol on a shop towel, cleanthe right front upper corner on the inside of thefront window. Remove the four adhesive backingsfrom the antenna, and attach the antenna to thefront window at the location shown. Install theantenna by applying sufficient pressure.

16. Route the antenna harness down the passenger’sA-pillar along the vehicle harness, secure theantenna harness to the vehicle harness withthree wire ties in areas shown.

13. Pull away the weatherstrip from around thedriver’s kick panel. Remove the driver’s kick panel(one screw clip and one clip).

WEATHERSTRIP(Pull away.)

DRIVER’SKICK PANEL

CLIP

SCREWCLIP

4703072T

VEHICLECLIP

VEHICLEHARNESS

ANTENNA

ANTENNAHARNESS

WIRETIE

ANTENNAHARNESS

VEHICLEHARNESS

PASSENGER’SA-PILLAR

10 mm

50 mm

ANTENNA

ANTENNA

4 ADHESIVEBACKINGS

FRONTWINDOW

PASSENGER’SA-PILLAR

BLACKPAINTEDAREA



4703111T

4703101T

4703083T

18. Wrap two EPT sealers around the antennaharness at the locations shown.

19. Route the antenna harness down behind thedashboard and towards the glove box. Secure theantenna harness to the vehicle harness with onewire tie.

20. Inside the glove box opening, route the antennaharness along the vehicle harness and towardsthe driver’s side of the vehicle. Secure theantenna harness to the vehicle harness withthree wire ties in areas shown.

21. Route the antenna harness past the audio unitopening, and secure the antenna harness to thevehicle harness with one wire tie.

WIRETIE

VEHICLEHARNESSVEHICLE

CLIPANTENNAHARNESS

GLOVE BOXOPENING

WIRETIES

VEHICLECLIPS

AUDIO UNITOPENING GLOVE BOX

OPENING

ANTENNAHARNESS VEHICLE

HARNESS

WIRE TIE

17. Using a felt-tip pen, mark the antenna harness atthe point where the harness touches thedashboard.

4703092T

PASSENGER’SA-PILLAR TRIMOPENING

GLOVE BOXOPENING

ANTENNAHARNESS

WIRE TIE

VEHICLEHARNESS

ANTENNAHARNESS

2 EPTSEALERS 50 mm

MARK(Align withthe mark.)

FELT-TIPPEN

DASHBOARD

ANTENNAHARNESS

LONG SIDE

SHORTSIDE

LONG SIDE

EPTSEALER

EPTSEALER



6421090B

ANTENNAHARNESS

WIRETIES

FRONT

DOOR SILL

WIRETIES

VEHICLEHARNESS

6421070B

WIRE TIE

VEHICLEFRAME

METER ASSEMBLYOPENINGVEHICLE

HARNESS

WIRE TIE

ANTENNAHARNESS

VEHICLEHARNESS

6421080B

ANTENNAHARNESS

WIRETIE

VEHICLEHARNESS

WIRETIES

METER ASSEMBLYOPENING

6421100B

DRIVER’SSEAT

WIRE TIEWITH CLIP

ANTENNAHARNESS

FLOOR CARPETCUTOUT

FLOORCARPET

BUSCABLE

550 mm

380 mm

22. Route the antenna harness as shown andtemporarily secure it to the vehicle harness usingtwo wire ties.

23. Route the antenna harness along the vehicleharness and temporarily secure it to the vehicleharness using four wire ties.

24. Route the antenna harness as shown andtemporarily secure it to the vehicle harness usingfour wire ties.

25. Route the antenna harness and bus cable underthe floor carpet and pull them out of the cutout inthe floor carpet.

26. Adjust the antenna harness and bus cable youjust pulled out of the cutout in the floor carpet tothe length shown.

27. Bind the antenna harness and bus cabletogether in the position shown using a wire tiewith clip.



4703260T

6421130B

DRIVER’SSEAT PIPE

FRONT

CUSHIONTEPE

XM TUNER

XM TUNER

corner

EPTSEALER

6421110B

DRIVER’S SEAT

6 mmFLANGE NUTS

6 x 16 mmWASHER-BOLTS

DRIVER’SSEAT PANEL

XM TUNERBRACKET 6 mm

FLANGE NUTS

XM TUNERBRACKET

6421120B

BUS CABLE14-PINCONNECTOR

ANTENNAHARNESS1-PINCONNECTOR

XM TUNER

WIRE TIEWITH CLIP

XM TUNERBRACKET

FRONT

XM TUNER

XM TUNERBRACKET

5 x 8 mmWASHER-SCREWS

XM TUNERBRACKET

5 x 8 mmWASHER-SCREWS

14-PIN CONNECTORLOCATION

2-PIN CONNECTORLOCATION

Installing the XM Tuner

28. Install the XM tuner brackets to the XM tuner withfour 5 x 8 mm washer-screws.

29. Install the XM tuner brackets to the driver’s seatpanel with four 6 x 16 mm washer-bolts and four 6mm flange nuts.

NOTE: If the vehicle is equipped with seat plate with welded nuts, the four flange nuts are not used.

30. Connect the antenna harness 1-pin connector andbus cable 14-pin connector to the XM tuner.

33. Attach the EPT sealer to the corner of the XMtuner as shown.

31. Install the wire tie with clip, with which you boundthe antenna harness and bus cable together instep 27, on the XM tuner bracket.

32. Using a isopropyl alcohol clean the vehicle panelsurface where the EPT sealer will be attached.Attach the antenna harness cord and bus cablecord to the XM tuner using a cushion tape asshown.

ANTENNAHARNESS

BUS CABLE



6421140B

FRONT

6421160B

6421150B

WIRETIES

VEHICLEHARNESS

BUSCABLE

ANTENNAHARNESS

WIRETIES

DOOR SILL

WIRETIES

VEHICLEHARNESS

BUSCABLE

ANTENNAHARNESS


WIRETIE

WIRE TIEVEHICLEHARNESS


BUSCABLE

ANTENNAHARNESS

WIRE TIE

VEHICLEHARNESS

VEHICLEFRAME

34. Route the bus cable and antenna harness to thefront side of the car and secure it to the vehicleharness using four wire ties.

35. Route the bus cable and antenna harness to thetop of the car and secure it to the vehicle harnessusing four wire ties.

36. Route the bus cable as shown. Secure the buscable and antenna harness to the vehicle harnessusing two wire ties as shown.



4703240T

VEHICLECONNECTOR BUS CABLE

14-PINCONNECTOR

VEHICLECONNECTORS

AUDIO UNIT

4701131T

AUDIO UNIT INSTRUMENTPANEL

5 BOLTS (Reuse.)

6421170B

With Player

Without Player

4703250T

AUDIO UNIT

PLAYER

BUS CABLE14-PINCONNECTOR

VEHICLECONNECTOR

WIRETIE

VEHICLEHARNESS

AUDIOUNITOPENING

METERASSEMBLYOPENING

VEHICLE 20-PINCONNECTOR

BUSCABLE

BUS CABLE14-PIN CONNECTOR(Align with the vehicle20-pin connector.)

WIRE TIE

ANTENNAHARNESS

Routing the Bus Cable

37. Align the end of the bus cable connector with theend of the vehicle 20-pin connector and securethe bus cable to the vehicle harness using a wiretie.

38. Secure the bus cable and antenna harness to thevehicle harness using a wire tie. Bundle theexcess of the antenna harness and secure it tothe vehicle harness using a wire tie.

39. Plug the bus cable 14-pin connector and vehicleconnectors into the audio unit/player.

WIRE TIE



4703220T

DRIVER’S SEATCheck that theantenna harness andbus cable are notpulled too tight whenthe seat is movedback and forth.

40. Reinstall the audio unit.41. Slide the driver’s seat back and forth to check

that the antenna harness and bus cable are notpulled too tight or end up too loose.

42. Check that all wire harnesses are routed properlyand all connectors are plugged in.

43. Reconnect the negative cable to the battery.

44. Enter the customer’s radio anti-theft code, andreset the radio station presets.

45. Set the clock.

46. Check the operation of the XM radio systemaccording to the vehicle’s Owner’s Manualsupplied.

47. Reinstall all removed parts.

NOTE: Whenever the battery is disconnected, thedriver’s window AUTO function is disable.

48. Start the engine. Push down on the driver’swindow switch until the window is fully open.

49. Pull up on the driver’s window switch fully to closethe window completely, then hold the switch for 2seconds or more.

50. Test the window AUTO function.


AII32459-34084 07 Ridgeline xm radio - College Hills · PDF file2 of 11 AII 32459-34084 (0802)...

Documents

Transcript of AII32459-34084 07 Ridgeline xm radio - College Hills · PDF file2 of 11 AII 32459-34084 (0802)...