Affiliated Distributors Guide - ARCH Cutting Tools · 2019. 11. 14. · USCTI, ISA ULTRA-DEX Ph:...

Affiliated Distributors Guide

American Manufactur ing, Serving the World

WWW.ARCHCUTTINGTOOLS.COM

CONTACT INFORMATION

Richards Micro-ToolPh: (800) 233-9956Fax: (508) 747-4339

www.richardsmicrotool.com

Visit our website for more info and to find a distributor near you!

250 Cherry StreetPlymouth, MA 02360

Member of Affiliated Distributors, USCTI, ISA

ARCH SpecialsPh: (844) 321-2724

www.archspecials.com



ULTRA-DEXPh: (810) 638-5388Fax: (810 638-4001

Email: [email protected]


7144 Sheridan Road.Flushing, MI 48433


KEO CuttersPh: (888) 390-2050Fax: (888) 771-2062

Email: [email protected] Request: [email protected]

Specialty Quotes: [email protected]

www.keocutters.com


25040 Easy StreetWarren, MI 48089


CAT 40 ENDMILL HOLDERS

CAT40 End Mill Holders (1/8 - 1/2”)

Balanced to:G2.5 (20,000 rpm)G6.3 (12,000 rpm)

DesignationA

InsideDia.

BOutside

Dia.

CProj.

SMax

DepthE Set

Screw G2 Price* G6 Price*

CT40-EM012-250-G2/G6 .125 .690 2.50 -- .19 SS10-250 $117.00 $93.00

CT40-EM188-250-G2/G6 .188 .750 2.50 -- .44 SS10-250 $105.00 $80.00

CT40-EM188-400-G2/G6 .188 .750 4.00 -- .44 SS10-250 $135.00 $110.00

CT40-EM250-250-G2/G6 .250 .880 2.50 -- .44 SS1/4-250 $105.00 $80.00

CT40-EM250-400-G2/G6 .250 .880 4.00 -- .44 SS1/4-250 $121.00 $96.00

CT40-EM250-600-G2/G6 .250 .880 6.00 -- .44 SS1/4-250 $128.00 $104.00

CT40-EM312-250-G2/G6 .312 .880 2.50 -- .44 SS1/4-250 $105.00 $80.00

CT40-EM312-400-G2/G6 .312 .880 4.00 -- .44 SS1/4-250 $121.00 $96.00

CT40-EM312-600-G2/G6 .312 .880 6.00 -- .44 SS1/4-250 $128.00 $104.00

CT40-EM375-250-G2/G6 .375 1.000 2.50 -- .75 SS3/8-375 $105.00 $80.00

CT40-EM375-400-G2/G6 .375 1.000 4.00 -- .75 SS3/8-375 $121.00 $96.00

CT40-EM375-600-G2/G6 .375 1.000 6.00 -- .75 SS3/8-375 $121.00 $96.00

CT40-EM437-250-G2/G6 .437 1.000 2.50 -- .75 SS3/8-375 $105.00 $80.00

CT40-EM437-400-G2/G6 .437 1.000 4.00 -- .75 SS3/8-375 $128.00 $104.00

CT40-EM500-262-G2/G6 .500 1.375 2.62 -- .88 SS7/16-500 $105.00 $80.00

CT40-EM500-400-G2/G6 .500 1.375 4.00 -- .88 SS7/16-500 $121.00 $96.00

CT40-EM500-600-G2/G6 .500 1.375 6.00 -- .88 SS7/16-500 $128.00 $104.00

* Add -G6 or -G2 to end of designation depending on the balance needed. All Hardware Included

- Taper Ground to AT-3 Specification- Balanced for Less Vibration & Longer Tool Life- T.I.R. .0002- Hardened & Tempered to Prevent Taper Cracking- Through Spindle Coolant Capability- Special Length Projections Available

1

HIGH PERFORMANCE SOLID END MILLS

2

Number Description Dia. Flute Length OAL End # Of

FlutesList

Price

80000 1/8X3/8X1.5 SQ 4FL PATRIOT END MILL 1/8 3/8 1-1/2 SQUARE 4 $28.59

80002 3/16X1/2X2 SQ 4FL PATRIOT END MILL 3/16 1/2 2 SQUARE 4 $31.88



80008 3/8X1X2.5 SQ 4FL PATRIOT END MILL 3/8 1 2-1/2 SQUARE 4 $69.07

80012 7/16X1X3 SQ 4FL PATRIOT END MILL 7/16 1 3 SQUARE 4 $106.26


80017 1/2X1X3 SQ 4FL PATRIOT END MILL 1/2 1 3 SQUARE 4 $109.80

80021 1/2X1X3 R.030 4FL PATRIOT END MILL 1/2 1 3 SQUARE 4 $109.80

80023 5/81-1/4X35 SQ 4FL PATRIOT END MILL 5/8 1-1/4 3-1/2 SQUARE 4 $144.97

80025 3/4X1-1/2X4 SQ 4FL PATRIOT END MILL 3/4 1-1/2 4 SQUARE 4 $201.77

Number Description Dia. FluteLength OAL Rad. # Of

FlutesList

Price

80001 1/8X3/8X1.5 R.005 4FL PATRIOT END MILL 1/8 3/8 1-1/2 0.005 4 $28.59

80003 3/16X1/2X2 R.010 4 FL PATRIOT END MILL 3/16 1/2 2 0.010 4 $31.88

80005 1/4X3/4X2.5 R.010 4 FL PATRIOT END MILL 1/4 3/4 2-1/2 0.010 4 $42.76

80007 5/16X13/16X2.5 R.015 4 FL PATRIOT END MILL 5/16 13/16 2-1/2 0.015 4 $55.66

80009 3/8X1X2.5 R.010 4 FL PATRIOT END MILL 3/8 1 2-1/2 0.010 4 $69.07



80013 7/16X1X3 R.020 4 FL PATRIOT END MILL 7/16 1 3 0.020 4 $106.26

80015 1/2X5/8X2.5 CR.010 4 FL STUB 1/2 5/8 2-1/2 0.010 4 $109.80

80016 1/2X5/8X3 R.020 4 FL PATRIOT END MILL 1/2 5/8 3 0.020 4 $109.80




80022 1/2X1-1/4 X3 R.020 4 FL PATRIOT END MILL 1/2 1-1/4 3 0.020 4 $109.80

80024 5/8X1-1/4 X3.5 R.025 4 FL PATRIOT END MILL 5/8 1-1/4 3-1/2 0.025 4 $144.97



Square End

Round End

SQUARE SHANK & INSERTS

3

Designation A/B COAL L F Insert Shim Lock

Pin Clamp Screw Price

MCLNR/L 12-4B .750 4.5 1.300 1.000

CNMG 432 ICSN-433 NL-46 CL-20 XNS-48

$67.00

MCLNR/L 16-4D 1.000 6 1.600 1.250 $73.00

MCLNR/L 20-4D 1.250 6 1.600 1.500 $80.00

MCLNR/L 16-5D 1.000 6 1.600 1.250


$73.00

MCLNR/L 20-5D 1.250 6 1.600 1.570 $80.00

MCLNR/L 24-5D 1.500 6 1.600 2.000 $106.00

MCLNR/L 16-6D 1.000 6 1.600 1.250


$73.00

MCLNR/L 20-6D 1.250 6 1.600 1.570 $80.00

MCLNR/L 24-6D 1.500 6 1.600 2.000 $106.00

MCLNR/L 24-6E 1.500 7 1.600 2.000 $106.00

Negative 80° Diamond (-5° Lead) No Coolant

Grade

HP2

30

HP2

50

HM

240

HM

250

HS2

20

HN

432

HK

036

UD

51

UD

52

UD

21

UD

2

UD

22

UD

32

UD

5C

UD

5CT

UD

1

DesignationCNMG 432-CM2 - - - $9.80 - - - - - - - - - - - -

CNGP 432-CM3 - - $18.00 - - - - - - - - - - - - -

CNMG 543-CP2 - $18.00 - - - - - - - - - - - - - -

CNMG 643-CP2 - $23.00 - - - - - - - - - - - - - -

CNMG 432-CX1 $9.80 $9.80 - - - - - - - - - - - - - -

CNMG 432-ZK1 - - - - - - - - - $8.60 - - - - - -

CNMG 543-ZK1 - - - - - - - - - $12.00 - - - - - -

CNMG 643-ZK1 - - - - - - - - - $15.00 - - - - - -

CNMG 432-ZM1 - - - - - - - - - - - - $8.60 - - -

CNMG 432-ZP1 - - - - - - - $8.60 $8.60 - - - - - - -

CNMG 543-ZP1 - - - - - - - $12.00 $12.00 - - - - - - -

CNMG 643-ZP1 - - - - - - - $15.00 $15.00 - - - - - - -

CNMA 432 - - - - - - $9.80 - - - - - - - - -

CNMA 543 - - - - - - $16.00 - - - - - - - - -

CNMA 643 - - - - - - $21.00 - - - - - - - - -

Inserts sold in packs of 10

CM2 CM3 CP2 CS1 CX1 ZK1 ZM1 ZP1 CNMA Flat Top

CARBIDE POS 80° BORING BARS

4

Designation DDia.

COAL F Min

Bore Insert InsertScrew Key Price

C02.5G SCLDR/L1.2 .156 3.5 .090 .175CDHB 1.20.60

MTS-182

T-6

$156.00

C03H SCLDR/L1.2 .187 4 .102 .205 MTS-183 $156.00

C03.5H SCLDR/L1.5 .218 4 .125 .245CDGW 1.510 MTS-184

$156.00

C04H SCLDR/L1.5 .250 4 .172 .312 $156.00

C05K SCLPR/L1.8 .312 5 .219 .395 CPMT 1.61.20.5 MTS-224

T-7

$156.00

C06M SCLPR/L2 .375 6 .250 .460

CPMT 21.51 MTS-255

$179.00

C08J SCLPR/L2 .500 4.5 .312 .600 $202.00

C08R SCLPR/L2 .500 8 .312 .600 $232.00

C08J SCLPR/L3 .500 4.5 .344 .625CPMT 32.51 MTS-35 T-15

$202.00

CO8R SCLPR/L3 .500 8 .344 .625 $232.00

C06M SCLCR/L2 .375 6 .250 .460

CCMT 21.51 MTS-255 T-7

$179.00

C08J SCLCR/L2 .500 4.5 .312 .600 $202.00

C08R SCLCR/L2 .500 8 .312 .600 $232.00

C08J SCLCR/L3 .500 4.5 .344 .625CCMT 32.51 MTS-35 T-15

$202.00

C08R SCLCR/L3 .500 8 .344 .625 $232.00

Designation DDia.

COAL F Min


E02.5G SCLDR/L1.2 .156 3.5 .090 .175CDHB 1.20.60

MTS-182

T-6

$176.00

E03H SCLDR/L1.2 .187 4 .102 .205 MTS-183 $176.00

E03.5H SCLDR/L1.5 .218 4 .125 .245CDGW 1.510 MTS-184

$176.00

E04H SCLDR/L1.5 .250 4 .172 .312 $176.00

E05K SCLPR/L1.8 .312 5 .219 .395 CPMT 1.61.20.5 MTS-224

T-7

$176.00

E06M SCLPR/L2 .375 6 .250 .460

CPMT 21.51 MTS-255

$197.00

E08J SCLPR/L2 .500 4.5 .312 .600 $221.00

E08R SCLPR/L2 .500 8 .312 .600 $250.00

E10Q SCLPR/L2 .625 7 .406 .770 $311.00

E10S SCLPR/L3 .625 10 .406 .770 $379.00

E08J SCLPR/L3 .500 4.5 .344 .625

CPMT 32.51 MTS-35 T-15

$221.00

E08R SCLPR/L3 .500 8 .344 .625 $250.00

E10Q SCLPR/L3 .625 7 .406 .760 $311.00

E10S SCLPR/L3 .625 10 .406 .760 $379.00

E12Q SCLPR/L3 .750 7 .500 .920 $391.00

E12S SCLPR/L3 .750 10 .500 .920 $452.00

E16R SCLPR/L3 1.000 8 .625 1.185 $578.00

E16T SCLPR/L3 1.000 12 .625 1.185 $736.00

Positive 80° Diamond (-5° Lead) 8:1 Ratio No Coolant

Positive 80° Diamond (-5° Lead) 8:1 Ratio Coolant Thru

BORING BAR INSERTS

5

Grade

HP2

30

HP2

50

HM

240

HM

250

HS2

20

HN

432

HK

036

UD

51

UD

52

UD

21

UD

2

UD

22

UD

32

UD

5C

UD

5CT

UD

1

Designation

CPMT 1.81.20.5-LX6 - - - - - - - $11.00 $13.00 $12.00 $9.50 - - $9.80 $12.00 -

CPMT 21.51-LX6 - - - - - - - $8.40 $10.60 $9.50 $7.10 - - $9.80 $12.00 -

CPMT 32.51-LX6 - - - - - - - $8.80 $10.60 $10.20 $7.40 - - - - -

Grade

HP2

30

HP2

50

HM

240

HM

250

HS2

20

HN

432

HK

036

UD

51

UD

52

UD

21

UD

2

UD

22

UD

32

UD

5C

UD

5CT

UD

1

DesignationCDGW 1.510 - - - - - - - $8.70 $9.60 $9.10 $8.70 - - $8.50 $10.40 -

CDHB 1.20.60 - - - - - - - $8.30 $8.70 $8.70 $7.00 - - $7.80 $9.50 -

Grade

HP2

30

HP2

50

HM

240

HM

250

HS2

20

HN

432

HK

036

UD

51

UD

52

UD

21

UD

2

UD

22

UD

32

UD

5C

UD

5CT

UD

1

Designation

CCMT 21.51-CX1 $7.60 $7.60 - $7.60 - - - - - - - - - - - -

CCMT 32.51-CX1 $8.00 $8.00 - $8.00 - - - - - - - - - - - -

CCMT 21.51-ZM1 - - - - - - - - - - - - $6.70 - - -

CCMT 32.51-ZM1 - - - - - - - - - - - - $7.10 - - -

CCGX 21.51-ZN1 - - - - - - - - - - - - - - - $7.80

CCGX 32.51-ZN1 - - - - - - - - - - - - - - - $8.10

CCMT 21.51-ZX3 - - - - - - - $6.70 $6.70 $6.70 - - - - - -

CCMT 32.51-ZX3 - - - - - - - $7.10 $7.10 $7.10 - - - - - -


LX6

CX1 ZM1 ZN1 ZX3

CDGW Flat Top CDHB Flat Top

HIGH PERFORMANCE DRILL INSERTS & SPECSHIGH PERFORMANCE INDEXABLE DRILLS

6

3XD Indexable Drills Coolant Thru

Designation D d d1 L3 L1 L2 Insert Screw List Price

PD1-0562-3D-075 .562

.750 1.120 1.900

2.747 1.804

PD1 042004PD1-16WrenchT-6-S

$243.00

PD1-0594-3D-075 .594 2.843 1.900 $243.00

PD1-0609-3D-075 .609 2.888 1.945 $243.00

PD1-0625-3D-075 .625 2.936 1.993

PD1 052804PD1-2

WrenchT-6-S

$243.00

PD1-0669-3D-075 .669 (17mm) 3.069 2.126 $243.00

PD1-0687-3D-075 .687 3.122 2.179 $243.00

PD1-0709-3D-075 .709 (18mm) 3.187 2.244 $243.00

PD1-0734-3D-100 .734

1.000 1.360 2.400

3.263 2.320


$243.00

PD1-0750-3D-100 .750 3.311 2.368 $276.00

PD1-0787-3D-100 .787 (20mm) 3.422 2.479 $276.00

PD1-0812-3D-100 .812 3.499 2.556 $276.00

PD1-0844-3D-100 .844 3.637 2.694 $276.00

PD1-0875-3D-100 .875 3.686 2.743 $276.00

PD1-0937-3D-125 .937

1.250

1.614

2.900

3.874 2.931


$276.00

PD1-0984-3D-125 .984 (25mm) 4.014 3.071 $276.00

PD1-1000-3D-125 1.000 4.061 3.118 $312.00

PD1-1062-3D-125 1.062 4.249 3.306 $312.00

PD1-1125-3D-125 1.125 4.436 3.493 $312.00

PD1-1181-3D-125 1.181 (30mm) 4.645 3.702

PD1 094508

PD1-35

WrenchT-15-S

$312.00

PD1-1250-3D-125 1.250

1.980

4.850 3.907 $353.00

PD1-1312-3D-125 1.312 5.039 4.095 $353.00

PD1-1375-3D-125 1.375 5.225 4.282 $353.00

PD1-1437-3D-125 1.437 5.413 4.470 $353.00

PD1-1500-3D-150 1.500

1.500

1.980

2.900

5.640 4.697

PD1 125812PD1-5

WrenchT-20-S

$404.00

PD1-1625-3D-150 1.625 6.015 5.072 $427.00

PD1-1750-3D-150 1.750 6.390 5.447 $445.00

PD1-1875-3D-150 1.875 6.825 5.882

PD1 156812PD1-5

WrenchT-20-S

$505.00

PD1-2000-3D-150 2.000 1.940 7.140 6.197 $535.00

PD1-2125-3D-150 2.125 2.065 7.515 6.572 $586.00

HIGH PERFORMANCE DRILL INSERTS & SPECS

7

Grade Description

HK 356 Stable cutting performance for drilling cast iron. Suitable for aluminum. Recommended for mild structural steel, difficult chip controlled steel.

HP 600 Super tough substrate with PVD coating. Excellent for drilling steel and stainless steel.

Insert Grade Conditions

Designation HP600 HK356

PD1 042004 $9.10 $9.10

PD1 052804 $9.10 $9.10

PD1 063306 $9.30 $9.30

PD1 074006 $9.70 $9.70

PD1 094508 $11.00 $11.00

PD1 125812 $13.00 $13.00

PD1 156812 $14.00 $14.00


Speeds and Feeds Ø.562-.734 Ø.750-1.437 Ø1.50-2.125

Insert Grade SFM Inch/Rev Inch/Rev Inch/Rev

Steel HP600 400-700 .002-.005 .004-.008 .004-.010

Cast Iron HK356 350-650 .0025-.005 .004-.008 .004-.010

Stainless Steel HP600 300-600 .002-.005 .004-.008 .004-.010

Aluminum HK356 800-1400 .003-.008 .004-.010 .005-.012

Heat Resistant Steels HP600 90-250 .002-.004 .0025-.006 .0025-.0085

HIGH PERFORMANCE MILL INSERTS HIGH PERFORMANCE INDEXABLE MILLS

8

PM145° Cutter for face/slot milling and chamfering.

PM3High Feed Cutter for face, slot, plunge milling and angled ramping.

PM445° Cutter for face/slot milling and chamfering.

PM290° Cutter for face, slot, and shoulder milling.

Designation D Flutes C d Insert Screw PricePM1-1.25-3-.500-12 1.250 3 1.750 .500

PM1 1205 PM1-4

$264.00

PM1-1.50-4-.500-12 1.500 4 1.750 .500 $294.00

PM1-2.00-5-.750-12 2.000 5 1.750 .750 $407.00

PM1-2.50-6-1.00-12 2.500 6 2.000 1.000 $407.00

PM1-3.00-8-1.00-12 3.000 8 2.000 1.000 $525.00

PM1-4.00-10-1.25-12 4.000 10 2.000 1.250 $641.00


PM2 09T308 PM2-3

$271.00

PM2-1.50-5-.500-09 1.500 5 1.750 .500 $305.00

PM2-2.00-6-.750-09 2.000 6 1.750 .750 $364.00

PM2-2.50-7-1.00-09 2.500 7 2.000 1.000 $414.00

PM2-3.00-9-1.00-09 3.000 8 2.000 1.000 $518.00


PM3 10T308 PM3-3.5

$305.00

PM3-2.00-5-.750-10 2.000 5 1.750 .750 $364.00

PM3-2.50-6-1.00-10 2.500 6 2.000 1.000 $395.00


PM4 0604 PM4-4

$308.00

PM4-2.00-5-.750-06 2.000 5 1.750 .750 $327.00

PM4-2.50-6-1.00-06 2.500 6 2.000 1.000 $389.00

PM4-3.00-7-1.00-06 3.000 7 2.000 1.000 $492.00

PM4-4.00-9-1.25-06 4.000 9 2.000 1.250 $592.00

PM1 Face Mill Cutter Coolant Thru




All dimensions are in inches.

HIGH PERFORMANCE MILL INSERTS HIGH PERFORMANCE INDEXABLE MILLS

9

Designation HP470 HM470 HS470 HS480 HK430 HN432PM1 1205-HCX $21.00 - - - - -

PM1 1205-SCX - $21.00 $28.00 - $21.00 -

Designation HP470 HM470 HS470 HS480 HK430 HN432PM2 09T308-HCX $12.00 - - - - -

PM2 09T308-SCX - $12.00 $19.00 $19.00 - -

PM2 09T308-CCX - - - - $12.00 -

PM2 09T308-LCX - - - - - $14.00

Designation HP470 HM470 HS470 HS480 HK430 HN432PM3 10T308-HCX $12.00 - - - $12.00 -

PM3 10T308-SCX - $12.00 $15.00 $17.00 - -

Designation HP470 HM470 HS470 HS480 HK430 HN432PM4 0604-HCX $14.00 - - - $14.00 -

PM4 0604-SCX - $14.00 $18.00 - - -

PM4 0604-LCX - - - - - $20.00

PM1 PM2 PM3 PM4

Grade SFM Inch/Tooth

Ap(Inch)

Inch/Tooth

Ap(Inch)

Inch/Tooth

Ap(Inch)

Inch/Tooth

Ap(Inch)

Steel HP470 200-720 .004-.020 .007-.236 .002-.010 .004-.157 .004-.020 .003-.031 .004-.015 .011-.150

Stainless Steel HM470 200-650 .003-.016 .007-.236 .002-.010 .004-.157 .004-.020 .003-.031 .004-.010 .011-.150

Cast Iron HK430 350-1050 .003-.017 .007-.236 .002-.010 .004-.157 - - .003-.012 .011-.150

Non Ferrous HN432 <6500 - - .002-.011 .004-.157 - - .004-.015 .011-.150

Heat Resistant HS470 80-250 .003-.010 .007-.236 .002-.006 .004-.157 .004-.020 .003-.031 .002-.005 .007-.150

Titanium HS480 80-250 - - .002-.006 .004-.157 .004-.020 .003-.031 - -

Grade DescriptionHP 470 Suitable for demanding steel milling applications, interrupted cut.

HM 470 Stainless steel milling grade, PVD, TiAlN coating.

HS 470 First choice for milling heat-resistant alloys.

HS 480 Extremely heat resistant tough grade for milling titanium.

HK 430 Milling grade for cast iron.

HN 432 Ideal grade for aluminum. Low tendency for adhesion.




Insert Grade Conditions

Inserts sold in packs of 10HCX

HCX

SCX

HCX

HCX

SCX

LCX

CCX

SCX

SCX

LCX

10

Tuneable from the end with supplied T-Handle Hex Wrench.

Standard (Pin) Bars (English) Coolant Thru

Positive 80° Diamond (-5° Lead) 8:1 Ratio Coolant Thru

Designation D Dia.

COAL F Min


D08R SCLCR2 .500 8 .281 .580 CCMT 21.51 MTS-255 T-7 $653.00

D10X SCLCR3 .625 9 .406 .770 CCMT 32.51 MTS-35 T-15 $708.00

D12S SCLCR3 .750 10 .500 .930 CCMT 32.51 MTS-35 T-15 $763.00

Designation D Dia.

d1(Coupling)

COAL

Min Bore

HeadBolts Thread Price

5:1 RatioCFT B2500-16 2.500 2.500 16 2.800 5/16-18 HB 1/8-27 NPT $1,914.00

7:1 RatioCFT B1000-10 1.000 1.000 10 1.200 8-32 HB 1/8-27 NPT $889.00

CFT B1250-12 1.250 1.250 12 1.470 10-24 HB 1/8-27 NPT $993.00

CFT B1500-15 1.500 1.500 15 1.760 10-24 HB 1/8-27 NPT $1,158.00

CFT B2000-20 2.000 2.000 20 2.400 1/4-20 HB 1/8-27 NPT $1,407.00

CFT B2500-27 2.500 2.500 27 2.800 5/16-18 HB 1/4-18 NPT $1,914.00

10:1 RatioCFT B1000-14 1.000 1.000 14 1.200 8-32 HB 1/8-27 NPT $1,716.00

CFT B1250-16 1.250 1.250 16 1.470 10-24 HB 1/8-27 NPT $1,870.00

CFT B1500-19 1.500 1.500 19 1.760 10-24 HB 1/8-27 NPT $1,919.00

CFT B1750-23 1.750 1.750 23 2.010 1/4-20 HB 1/8-2 NPT $2,024.00

CFT B2000-26 2.000 2.000 26 2.400 1/4-20 HB 1/8-27 NPT $2,134.00

11

OTHER STYLES AVAILABLESTANDARD PIN CONNECTION

Positive 80° Diamond (-5° Lead)

Coolant ThruDesignationRight Hand

DDia.

COAL F Min

Bore Insert Insert Screw Key Price

MH16 SCLCR3-CFT 1.000 .790 .625 1.200 CCMT 32.51 MTS-35 T-15 $169.00

MH20 SCLCR3-CFT 1.250 1.250 .765 1.470 CCMT 32.51 MTS-35 T-15 $174.00

MH24 SCLCR3-CFT 1.500 1.250 .890 1.760 CCMT 32.51 MTS-35 T-15 $185.00

MH28 SCLCR3-CFT 1.750 1.250 1.015 2.030 CCMT 32.51 MTS-35 T-15 $192.00

MH24 SCLCR4-CFT 1.500 1.250 .890 1.760 CCMT 432 MTS-4 T-20 $192.00

MH28 SCLCR4-CFT 1.750 1.250 1.015 2.030 CCMT 432 MTS-4 T-20 $192.00



DesignationLeft Hand

DDia.

COAL F Min


MH16 SCLCL3-CFT 1.000 .790 .625 1.200 CCMT 32.51 MTS-35 T-15 $169.00

MH20 SCLCL3-CFT 1.250 1.250 .765 1.470 CCMT 32.51 MTS-35 T-15 $182.00

MH24 SCLCL3-CFT 1.500 1250 .890 1.760 CCMT 32.51 MTS-35 T-15 $196.00

MH28 SCLCL3-CFT 1.750 1.250 1.015 2.030 CCMT 32.51 MTS-35 T-15 $196.00

MH32 SCLCL4-CFT 2.000 1.625 1.281 2.400 CCMT 432 MTS-4 T-20 $215.00

MH40 SCLCL4-CFT 2.000 1.625 1.500 2.800 CCMT 432 MTS-4 T-20 $230.00

Our Chatter-Free Tooling (CFT) utilizes Tunable Internal Dampening Technology. This technology enables extended reaches of up to 10x bar diameter and 14x bar diameter with our carbide reinforced bars. Increase productivity with higher feed rates and improved surface finishes. The CFT modular system gives the operator the ability to perform multiple operations with one bar. We offer heads for roughing, finishing, grooving, and threading.

BALL END, STANDARD DECIMAL .005”-.045”

12

• Helix: 30° • Uncoated for General Purpose• Hand: RHS / RHC • ALTIN for High Performance• Rake Angle: Positive • Diameter Tolerance: +/- .0005• Center Cutting: Yes

Diameter Flute Length Shank Dia. OAL Uncoated ALTIN Coated(Ø) (FL) (SØ) 2 Flute 3 Flute 4 Flute Price 2 Flute 4 Flute Price

.005” .015” .125” 1.50” 874-.005 - - $25.41 874-E-.005 - $29.54

.006” .018” .125” 1.50” 874-.006 - - $25.41 874-E-.006 - $29.54

.007” .021” .125” 1.50” 874-.007 - - $25.41 874-E-.007 - $29.54

.008” .024” .125” 1.50” 874-.008 - - $25.41 874-E-.008 - $29.54

.009” .027” .125” 1.50” 874-.009 - - $25.41 874-E-.009 - $29.54

.010” .030” .125” 1.50” 874-.010 887-.010 875-.010 $20.52 874-E-.010 875-E-.010 $24.68

.011” .033” .125” 1.50” 874-.011 887-.011 875-.011 $20.52 874-E-.011 875-E-.011 $24.68

.012” .036” .125” 1.50” 874-.012 887-.012 875-.012 $20.52 874-E-.012 875-E-.012 $24.68

.013” .039” .125” 1.50” 874-.013 887-.013 875-.013 $20.52 874-E-.013 875-E-.013 $24.68

.014” .042” .125” 1.50” 874-.014 887-.014 875-.014 $20.52 874-E-.014 875-E-.014 $24.68

.015” .045” .125” 1.50” 874-.015 887-.015 875-.015 $18.22 874-E-.015 875-E-.015 $22.39

.0156” (1/64”) .0468” .125” 1.50” 874-1560 887-1560 875-1560 $18.22 - -

.016” .048” .125” 1.50” 874-.016 - 875-.016 $18.22 874-E-.016 875-E-.016 $22.39

.017” .051” .125” 1.50” 874-.017 - 875-.017 $18.22 874-E-.017 875-E-.017 $22.39

.018” .054” .125” 1.50” 874-.018 887-.018 875-.018 $18.22 874-E-.018 875-E-.018 $22.39

.019” .057” .125” 1.50” 874-.019 - 875-.019 $18.22 874-E-.019 875-E-.019 $22.39

.0197” (.5 mm) .0591” .125” 1.50” 874-0197 887-0197 875-0197 $18.22 - -

.020” .060” .125” 1.50” 874-.020 887-.020 875-.020 $17.39 874-E-.020 875-E-.020 $21.56

.021” .063” .125” 1.50” 874-.021 - 875-.021 $17.39 874-E-.021 875-E-.021 $21.56

.022” .066” .125” 1.50” 874-.022 - 875-.022 $17.39 874-E-.022 875-E-.022 $21.56

.023” .069” .125” 1.50” 874-.023 887-.023 875-.023 $17.39 874-E-.023 875-E-.023 $21.56

.024” .072” .125” 1.50” 874-.024 887-.024 875-.024 $17.39 874-E-.024 875-E-.024 $21.56

.025” .075” .125” 1.50” 874-.025 887-.025 875-.025 $16.03 874-E-.025 875-E-.025 $20.20

.026” .078” .125” 1.50” 874-.026 887-.026 875-.026 $16.03 874-E-.026 875-E-.026 $20.20

.027” .081” .125” 1.50” 874-.027 - 875-.027 $16.03 874-E-.027 875-E-.027 $20.20

.028” .084” .125” 1.50” 874-.028 - 875-.028 $16.03 874-E-.028 875-E-.028 $20.20

.029” .087” .125” 1.50” 874-.029 887-.029 875-.029 $16.03 874-E-.029 875-E-.029 $20.20

.030” .090” .125” 1.50” 874-.030 887-.030 875-.030 $16.03 874-E-.030 875-E-.030 $20.20

.031” (1/32”) .093” .125” 1.50” 874-.031 887-.031 875-.031 $16.03 874-E-.031 875-E-.031 $20.20

.032” .096” .125” 1.50” 874-.032 - 875-.032 $16.03 874-E-.032 875-E-.032 $20.20

.033” .099” .125” 1.50” 874-.033 887-.033 875-.033 $16.03 874-E-.033 875-E-.033 $20.20

.034” .102” .125” 1.50” 874-.034 - 875-.034 $16.03 874-E-.034 875-E-.034 $20.20

.035” .105” .125” 1.50” 874-.035 887-.035 875-.035 $13.53 874-E-.035 875-E-.035 $17.70

.036” .108” .125” 1.50” 874-.036 - 875-.036 $13.53 874-E-.036 875-E-.036 $17.70

.037” .111” .125” 1.50” 874-.037 - 875-.037 $13.53 874-E-.037 875-E-.037 $17.70

.038” .114” .125” 1.50” 874-.038 - 875-.038 $13.53 874-E-.038 875-E-.038 $17.70

.039” .117” .125” 1.50” 874-.039 - 875-.039 $13.53 874-E-.039 875-E-.039 $17.70

.0394” (1.0 mm) .1182” .125” 1.50” 874-0394 887-0394 875-0394 $13.53 874-E-0394 875-E-0394 $17.70

.040” .120” .125” 1.50” 874-.040 887-.040 875-.040 $13.53 874-E-.040 875-E-.040 $17.70

.041” .123” .125” 1.50” 874-.041 - 875-.041 $13.53 874-E-.041 875-E-.041 $17.70

.042” .126” .125” 1.50” 874-.042 - 875-.042 $13.53 874-E-.042 875-E-.042 $17.70

.043” .129” .125” 1.50” 874-.043 - 875-.043 $13.53 874-E-.043 875-E-.043 $17.70

.044” .132” .125” 1.50” 874-.044 - 875-.044 $13.53 874-E-.044 875-E-.044 $17.70

.045” .135” .125” 1.50” 874-.045 887-.045 875-.045 $13.53 874-E-.045 875-E-.045 $17.70

SØ ØFL

OAL

BALL END, STANDARDDECIMAL .005”-.044”

13

• Helix: 30° • Uncoated for General Purpose• Hand: RHS / RHC • ALTIN for High Performance• Rake Angle: Positive • Diameter Tolerance: +/- .0005• Center Cutting: Yes

Diameter Flute Length Shank Dia. OAL Uncoated ALTIN Coated(Ø) (FL) (SØ) 2 Flute 4 Flute Price 2 Flute Price

.005” .015” .125” 1.50” 882-.005 - $37.59 882-E-.005 $41.65

.006” .018” .125” 1.50” 882-.006 - $37.59 882-E-.006 $41.65

.007” .021” .125” 1.50” 882-.007 - $37.59 882-E-.007 $41.65

.008” .024” .125” 1.50” 882-.008 - $37.59 882-E-.008 $41.65

.009” .027” .125” 1.50” 882-.009 - $37.59 882-E-.009 $41.65

.010” .030” .125” 1.50” 882-.010 883-.010 $30.82 882-E-.010 $34.99

.011” .033” .125” 1.50” 882-.011 883-.011 $30.82 882-E-.011 $34.99

.012” .036” .125” 1.50” 882-.012 883-.012 $30.82 882-E-.012 $34.99

.013” .039” .125” 1.50” 882-.013 883-.013 $30.82 882-E-.013 $34.99

.014” .042” .125” 1.50” 882-.014 883-.014 $30.82 882-E-.014 $34.99

.015” .045” .125” 1.50” 882-.015 883-.015 $24.68 882-E-.015 $34.99

.0156” (1/64”) .0468” .125” 1.50” 882-1560 883-1560 $24.68 -

.016” .048” .125” 1.50” 882-.016 883-.016 $24.68 882-E-.016 $28.84

.017” .051” .125” 1.50” 882-.017 883-.017 $24.68 882-E-.017 $28.84

.018” .054” .125” 1.50” 882-.018 883-.018 $24.68 882-E-.018 $28.84

.019” .057” .125” 1.50” 882-.019 883-.019 $24.68 882-E-.019 $28.84

.0197” (.5 mm) .0591” .125” 1.50” 882-0197 883-0197 $23.74 -

.020” .060” .125” 1.50” 882-.020 883-.020 $23.74 882-E-.020 $27.91

.021” .063” .125” 1.50” 882-.021 883-.021 $23.74 882-E-.021 $27.91

.022” .066” .125” 1.50” 882-.022 883-.022 $23.74 882-E-.022 $27.91

.023” .069” .125” 1.50” 882-.023 883-.023 $23.74 882-E-.023 $27.91

.024” .072” .125” 1.50” 882-.024 883-.024 $23.74 882-E-.024 $27.91

.025” .075” .125” 1.50” 882-.025 883-.025 $21.56 882-E-.025 $25.71

.026” .078” .125” 1.50” 882-.026 883-.026 $21.56 882-E-.026 $25.71

.027” .081” .125” 1.50” 882-.027 883-.027 $21.56 882-E-.027 $25.71

.028” .084” .125” 1.50” 882-.028 883-.028 $21.56 882-E-.028 $25.71

.029” .087” .125” 1.50” 882-.029 883-.029 $21.56 882-E-.029 $25.71

.030” .090” .125” 1.50” 882-.030 883-.030 $19.47 882-E-.030 $23.64

.031” (1/32”) .093” .125” 1.50” 882-.031 883-.031 $19.47 882-E-.031 $23.64

.032” .096” .125” 1.50” 882-.032 883-.032 $19.47 882-E-.032 $23.64

.033” .099” .125” 1.50” 882-.033 883-.033 $19.47 882-E-.033 $23.64

.034” .102” .125” 1.50” 882-.034 883-.034 $19.47 882-E-.034 $23.64

.035” .105” .125” 1.50” 882-.035 883-.035 $18.32 882-E-.035 $22.49

.036” .108” .125” 1.50” 882-.036 883-.036 $18.32 882-E-.036 $22.49

.037” .111” .125” 1.50” 882-.037 883-.037 $18.32 882-E-.037 $22.49

.038” .114” .125” 1.50” 882-.038 883-.038 $18.32 882-E-.038 $22.49

.039” .117” .125” 1.50” 882-.039 883-.039 $18.32 882-E-.039 $22.49

.0394” (1.0 mm) .1182” .125” 1.50” 882-0394 883-0394 $18.32 882-E-0394 $22.49

.040” .120” .125” 1.50” 882-.040 883-.040 $18.32 882-E-.040 $22.49

.041” .123” .125” 1.50” 882-.041 883-.041 $18.32 882-E-.041 $22.49

.042” .126” .125” 1.50” 882-.042 883-.042 $18.32 882-E-.042 $22.49

.043” .129” .125” 1.50” 882-.043 883-.043 $18.32 882-E-.043 $22.49

.044” .132” .125” 1.50” 882-.044 883-.044 $18.32 882-E-.044 $22.49

ØFL

OAL

SØ

BALL END, LONG SHANK, STUB DECIMAL .010”-.250”

14

• Helix: 30° • Center Cutting: Yes• Hand: RHS / RHC • Diameter Tolerance: .005” to .124”: +/-.0005• Rake Angle: Positive .125” to .375”: +0.000/-.002

Diameter Flute Length

ShankDia. OAL Uncoated ALTIN Coated Amorphous Diamond

(Ø) (FL) (SØ) 2 Flute Price 2 Flute Price 3 Flute Price.010” .015” .125” 2.50” 888XB-.010 $31.66 888XB-E-.010 $35.83 888XB-A-.010 $42.59

.015” .023” .125” 2.50” 888XB-.015 $28.95 888XB-E-.015 $33.12 888XB-A-.015 $39.88

.020” .030” .125” 2.50” 888XB-.020 $28.01 888XB-E-.020 $32.18 888XB-A-.020 $38.94

.025” .037” .125” 2.50” 888XB-.025 $22.49 888XB-E-.025 $26.66 888XB-A-.025 $33.42

.030” .045” .125” 2.50” 888XB-.030 $22.49 888XB-E-.030 $26.66 888XB-A-.030 $33.42

.031” .047” .125” 2.50” 888XB-.031 $22.49 888XB-E-.031 $26.66 888XB-A-.031 $33.42

.035” .053” .125” 2.50” 888XB-.035 $22.49 888XB-E-.035 $26.66 888XB-A-.035 $33.42

.040” .060” .125” 2.50” 888XB-.040 $22.49 888XB-E-.040 $26.66 888XB-A-.040 $33.42

.045” .068” .125” 2.50” 888XB-.045 $21.65 888XB-E-.045 $25.82 888XB-A-.045 $32.58

.047” .071” .125” 2.50” 888XB-.047 $21.65 888XB-E-.047 $25.82 888XB-A-.047 $32.58

.050” .075” .125” 2.50” 888XB-.050 $21.65 888XB-E-.050 $25.82 888XB-A-.050 $32.58

.055” .083” .125” 2.50” 888XB-.055 $21.65 888XB-E-.055 $25.82 888XB-A-.055 $32.58

.060” .090” .125” 2.50” 888XB-.060 $21.65 888XB-E-.060 $25.82 888XB-A-.060 $32.58

.062” .093” .125” 2.50” 888XB-.062 $21.65 888XB-E-.062 $25.82 888XB-A-.062 $32.58

.065” .098” .125” 2.50” 888XB-.065 $21.65 888XB-E-.065 $25.82 888XB-A-.065 $32.58

.070” .105” .125” 2.50” 888XB-.070 $21.65 888XB-E-.070 $25.82 888XB-A-.070 $32.58

.075” .113” .125” 2.50” 888XB-.075 $21.65 888XB-E-.075 $25.82 888XB-A-.075 $32.58

.078” .117” .125” 2.50” 888XB-.078 $21.65 888XB-E-.078 $25.82 888XB-A-.078 $32.58

.080” .120” .125” 2.50” 888XB-.080 $21.65 888XB-E-.080 $25.82 888XB-A-.080 $32.58

.085” .128” .125” 2.50” 888XB-.085 $21.65 888XB-E-.085 $25.82 888XB-A-.085 $32.58

.090” .135” .125” 2.50” 888XB-.090 $21.65 888XB-E-.090 $25.82 888XB-A-.090 $32.58

.093” .140” .125” 2.50” 888XB-.093 $21.65 888XB-E-.093 $25.82 888XB-A-.093 $32.58

.095” .143” .125” 2.50” 888XB-.095 $21.65 888XB-E-.095 $25.82 888XB-A-.095 $32.58

.100” .150” .125” 2.50” 888XB-.100 $21.65 888XB-E-.100 $25.82 888XB-A-.100 $32.58

.125” .1875” .125” 2.50” 888XB-.125 $21.65 888XB-E-.125 $25.82 888XB-A-.125 $32.58

.187” .281” .125” 2.50” 888XB-.187 $25.08 888XB-E-.187 $29.57 888XB-A-.187 $36.03

.250” .375” .125” 2.50” 888XB-.250 $29.04 888XB-E-.250 $36.33 888XB-A-.250 $39.98

SØ Ø

FL

OAL

BALL TAPERED RIB CUTTERSDECIMAL .020”-.060”

15

Long Flute

Extra Long Flute

• TIALN Nano Coating for Higher Performance, Extended Tool Life and Improved Chip Flow

• Use: Precision Finishing of Ferrous Materials

• Designed with a Long Flute design for Deep Cavity Machining of a variety of Materials

• Diameter Tolerance: +0/-.001


Shank Dia. OAL Taper Uncoated TIALN Nano Coated

(Ø) (FL) (SØ) 4 Flute Price 4 Flute Price.020” .140” .1875” 3.00” 0° 733XB-000G-020F $59.09 733XB-F-000G-020F $64.97

.030” .210” .1875” 3.00” 0° 733XB-000G-030F $55.08 733XB-F-000G-030F $61.45

.040” .280” .1875” 3.00” 0° 733XB-000G-040F $56.15 733XB-F-000G-040F $62.52

.050” .350” .1875” 3.00” 0° 733XB-000G-050F $56.15 733XB-F-000G-050F $62.52

.060” .420” .1875” 3.00” 0° 733XB-000G-060F $55.08 733XB-F-000G-060F $61.45

.020” .140” .1875” 3.00” .5° 733XB-005G-020F $59.09 733XB-F-005G-020F $64.97

.030” .210” .1875” 3.00” .5° 733XB-005G-030F $55.08 733XB-F-005G-030F $61.45

.040” .280” .1875” 3.00” .5° 733XB-005G-040F $56.15 733XB-F-005G-040F $62.52

.050” .350” .1875” 3.00” .5° 733XB-005G-050F $56.15 733XB-F-005G-050F $62.52

.060” .420” .1875” 3.00” .5° 733XB-005G-060F $55.08 733XB-F-005G-060F $61.45

.020” .140” .1875” 3.00” 1° 733XB-010G-020F $59.09 733XB-F-010G-020F $64.97

.030” .210” .1875” 3.00” 1° 733XB-010G-030F $55.08 733XB-F-010G-030F $61.45

.040” .280” .1875” 3.00” 1° 733XB-010G-030F $56.15 733XB-F-010G-030F $62.52

.050” .350” .1875” 3.00” 1° 733XB-010G-040F $56.15 733XB-F-010G-040F $62.52

.060” .420” .1875” 3.00” 1° 733XB-010G-050F $55.08 733XB-F-010G-050F $61.45


ShankDia. OAL Taper Uncoated TIALN Nano Coated

(Ø) (FL) (SØ) 4 Flute Price 4 Flute Price.020” .280” .1875” 3.00” 0° 733XB-0000-020F $55.08 733XB-F-0000-020F $64.97

.030” .410” .1875” 3.00” 0° 733XB-0000-030F $56.15 733XB-F-0000-030F $61.45

.040” .560” .1875” 3.00” 0° 733XB-0000-040F $56.15 733XB-F-0000-040F $62.52

.050” .700” .1875” 3.00” 0° 733XB-0000-050F $55.08 733XB-F-0000-050F $62.52

.060” .840” .1875” 3.00” 0° 733XB-0000-060F $55.08 733XB-F-0000-060F $61.45

.020” .280” .1875” 3.00” .5° 733XB-0050-020F $56.15 733XB-F-0050-020F $64.97

.030” .410” .1875” 3.00” .5° 733XB-0050-030F $56.15 733XB-F-0050-030F $61.45

.040” .560” .1875” 3.00” .5° 733XB-0050-040F $55.08 733XB-F-0050-040F $62.52

.050” .700” .1875” 3.00” .5° 733XB-0050-050F $55.08 733XB-F-0050-050F $62.52

.060” .840” .1875” 3.00” .5° 733XB-0050-060F $56.15 733XB-F-0050-060F $61.45

.020” .280” .1875” 3.00” 1° 733XB-0100-020F $56.15 733XB-F-0100-020F $64.97

.030” .410” .1875” 3.00” 1° 733XB-0100-030F $55.08 733XB-F-0100-030F $61.45

.040” .560” .1875” 3.00” 1° 733XB-0100-030F $56.15 733XB-F-0100-030F $62.52

.050” .700” .1875” 3.00” 1° 733XB-0100-040F $56.15 733XB-F-010-040F $62.52

.060” .840” .1875” 3.00” 1° 733XB-0100-050F $55.08 733XB-F-0100-050F $61.45

CORNER ROUNDING END MILLS DECIMAL .005”-.156”

16

• Application: End Cutting• Diameter Tolerance: +/- .0005”• TIN, ALTIN, and TIALN coating for High Performance

(R) (Ø) (SØ) OAL 2 Flute Price 2 Flute Price 2 Flute Price.005” .047” .125” 1.50” 839-2.005X.047 $27.17 839-T-2.005X.047 $32.33 839-E-2.005X.047 $32.38

.008” .047” .125” 1.50” 839-2.008X.047 $27.17 839-T-2.008X.047 $32.33 839-E-2.008X.047 $32.38

.010” .047” .125” 1.50” 839-2.010X.047 $27.17 839-T-2.010X.047 $32.33 839-E-2.010X.047 $32.38

.012” .047” .125” 1.50” 839-2.012X.047 $27.17 839-T-2.012X.047 $32.33 839-E-2.012X.047 $32.38

.015” .047” .125” 1.50” 839-2.015X.047 $27.17 839-T-2.015X.047 $32.33 839-E-2.015X.047 $32.38

.018” .047” .125” 1.50” 839-2.018X.047 $27.17 839-T-2.018X.047 $32.33 839-E-2.018X.047 $32.38

.020” .047” .125” 1.50” 839-2.020X.047 $27.17 839-T-2.020X.047 $32.33 839-E-2.020X.047 $32.38

.022” .047” .125” 1.50” 839-2.022X.047 $27.17 839-T-2.022X.047 $32.33 839-E-2.022X.047 $32.38

.025” .047” .125” 1.50” 839-2.025X.047 $27.17 839-T-2.025X.047 $32.33 839-E-2.025X.047 $32.38

.027” .047” .125” 1.50” 839-2.027X.047 $27.17 839-T-2.027X.047 $32.33 839-E-2.027X.047 $32.38

.030” .047” .125” 1.50” 839-2.030X.047 $27.17 839-T-2.030X.047 $32.33 839-E-2.030X.047 $32.38

.031” .047” .125” 1.50” 839-2.031X.047 $27.17 839-T-2.031X.047 $32.33 839-E-2.031X.047 $32.38

.032” .047” .125” 1.50” 839-2.032X.047 $27.17 839-T-2.032X.047 $32.33 839-E-2.032X.047 $32.38

.035” .047” .125” 1.50” 839-2.035X.047 $27.17 839-T-2.035X.047 $32.33 839-E-2.035X.047 $32.38

.039” .047” .125” 1.50” 839-2.039X.047 $27.17 839-T-2.039X.047 $32.33 839-E-2.039X.047 $32.38

.043” .047” .1875” 2.00” 839-2.043X.047 $35.62 839-T-2.043X.047 $41.58 839-E-2.043X.047 $41.65

.047” .047” .1875” 2.00” 839-2.047X.047 $35.62 839-T-2.047X.047 $41.58 839-E-2.047X.047 $41.65

.050” .047” .1875” 2.00” 839-2.050X.047 $35.62 839-T-2.050X.047 $41.58 839-E-2.050X.047 $41.65

.055” .047” .1875” 2.00” 839-2.055X.047 $35.62 839-T-2.055X.047 $41.58 839-E-2.055X.047 $41.65

.060” .047” .1875” 2.00” 839-2.060X.047 $36.34 839-T-2.060X.047 $42.32 839-E-2.060X.047 $42.38

.062” .047” .1875” 2.00” 839-2.062X.047 $36.34 839-T-2.062X.047 $42.32 839-E-2.062X.047 $42.38

.067” .047” .1875” 2.00” 839-2.067X.047 $36.34 839-T-2.067X.047 $42.32 839-E-2.067X.047 $42.38

.072” .047” .250” 2.00” 839-2.072X.047 $41.86 839-T-2.072X.047 $50.11 839-E-2.072X.047 $50.19

.078” .047” .250” 2.00” 839-2.078X.047 $41.86 839-T-2.078X.047 $50.11 839-E-2.078X.047 $50.19

.089” .047” .250” 2.00” 839-2.089X.047 $41.86 839-T-2.089X.047 $50.11 839-E-2.089X.047 $50.19

.093” .047” .250” 2.00” 839-2.093X.047 $41.86 839-T-2.093X.047 $50.11 839-E-2.093X.047 $50.19

.100” .047” .250” 2.00” 839-2.100X.047 $41.86 839-T-2.100X.047 $50.11 839-E-2.100X.047 $50.19

.104” .060” .3125” 2.50” 839-2.104X.060 $58.11 839-T-2.104X.060 $68.41 839-E-2.104X.060 $68.51

.109” .060” .3125” 2.50” 839-2.109X.060 $58.11 839-T-2.109X.060 $68.41 839-E-2.109X.060 $68.51

.118” .060” .3125” 2.50” 839-2.118X.060 $59.15 839-T-2.118X.060 $69.45 839-E-2.118X.060 $69.55

.125” .060” .3125” 2.50” 839-2.125X.060 $59.15 839-T-2.125X.060 $69.45 839-E-2.125X.060 $69.55

.140” .060” .375” 2.50” 839-2.140X.060 $67.79 839-T-2.140X.060 $80.15 839-E-2.140X.060 $80.28

.156” .060” .375” 2.50” 839-2.156X.060 $73.41 839-T-2.156X.060 $85.76 839-E-2.156X.060 $85.90

(R) (Ø) (SØ) OAL 4-Flute Price 4 Flute Price 4-Flute Price.010” .250” .375” 2.50” 839-4.010X.250 $46.76 839-T-4.010X.250 $59.16 839-E-4.010X.250 $59.25

.015” .250” .375” 2.50” 839-4.015X.250 $46.76 839-T-4.015X.250 $59.16 839-E-4.015X.250 $59.25

.020” .250” .375” 2.50” 839-4.020X.250 $46.76 839-T-4.020X.250 $59.16 839-E-4.020X.250 $59.25

.025” .250” .375” 2.50” 839-4.025X.250 $46.76 839-T-4.025X.250 $59.16 839-E-4.025X.250 $59.25

.030” .250” .375” 2.50” 839-4.030X.250 $51.23 839-T-4.030X.250 $63.62 839-E-4.030X.250 $63.72

.031” .250” .375” 2.50” 839-4.031X.250 $51.23 839-T-4.031X.250 $63.62 839-E-4.031X.250 $63.72

.039” .250” .375” 2.50” 839-4.039X.250 $51.23 839-T-4.039X.250 $63.62 839-E-4.039X.250 $63.72

.047” .250” .375” 2.50” 839-4.047X.250 $51.23 839-T-4.047X.250 $63.62 839-E-4.047X.250 $63.72

.050” .250” .375” 2.50” 839-4.050X.250 $51.23 839-T-4.050X.250 $63.62 839-E-4.050X.250 $63.72

KEYSEAT CUTTERS 6 & 8 FLUTEDECIMAL .125”-.375”

17

6 Flute, 1/4” Shank Diameter

8 Flute

Diameter Cutter Width Neck Length

Neck Dia.

Shank Dia. OAL Uncoated TIALN Coated

(Ø) (CW) (NL) (NØ) (SØ) 2.00” 6 Flute Price 6 Flute Price.125” .0156” .157” .0625” .250” 2.00” 809-20-0156 $41.44 809C-20-0156 $47.69

.125” .0312” .157” .0625” .250” 2.00” 809-20-0312 $41.44 809C-20-0312 $47.69

.125” .0394” .157” .0625” .250” 2.00” 809-20-0394 $41.44 809C-20-0394 $47.69

.125” .0469” .157” .0625” .250” 2.00” 809-20-0469 $41.44 809C-20-0469 $47.69

.125” .0625” .157” .0625” .250” 2.00” 809-20-0625 $41.44 809C-20-0625 $47.69

.125” .0937” .157” .0625” .250” 2.00” 809-20-0937 $41.44 809C-20-0937 $47.69

.125” .125” .157” .0625” .250” 2.00” 809-20-1250 $41.44 809C-20-1250 $47.69

.1875” .0156” .250” .0937” .250” 2.00” 809-21-0156 $41.44 809C-21-0156 $47.69

.1875” .0312” .250” .0937” .250” 2.00” 809-21-0312 $41.44 809C-21-0312 $47.69

.1875” .0394” .250” .0937” .250” 2.00” 809-21-0394 $41.44 809C-21-0394 $47.69

.1875” .0469” .250” .0937” .250” 2.00” 809-21-0469 $41.44 809C-21-0469 $47.69

.1875” .0625” .250” .0937” .250” 2.00” 809-21-0625 $41.44 809C-21-0625 $47.69

.1875” .0937” .250” .0937” .250” 2.00” 809-21-0937 $41.44 809C-21-0937 $47.69

.1875” .125” .250” .0937” .250” 2.00” 809-21-1250 $41.44 809C-21-1250 $47.69

.1875” .1875” .250” .0937” .250” 2.00” 809-21-1875 $41.44 809C-21-1875 $47.69

Diameter Cutter Width

NeckLength

NeckDia.

ShankDia. OAL Uncoated ALTIN Coated TIALN Coated

(Ø) (CW) (NL) (NØ) (SØ) 8 Flute Price 8 Flute Price 8 Flute Price.250” .0156” .250” .125” .250” 2.00” 809-22-0156 $41.44 809-E-22-0156 $47.69 809C-22-0156 $47.69

.250” .0312” .250” .125” .250” 2.00” 809-22-0312 $41.44 809-E-22-0312 $47.69 809C-22-0312 $47.69

.250” .0394” .250” .125” .250” 2.00” 809-22-0394 $41.44 809-E-22-0394 $47.69 809C-22-0394 $47.69

.250” .0469” .250” .125” .250” 2.00” 809-22-0469 $41.44 809-E-22-0469 $47.69 809C-22-0469 $47.69

.250” .0625” .250” .125” .250” 2.00” 809-22-0625 $41.44 809-E-22-0625 $47.69 809C-22-0625 $47.69

.250” .125” .250” .125” .250” 2.00” 809-22-1250 $41.44 809-E-22-1250 $47.69 809C-22-1250 $47.69

.250” .1875” .250” .125” .250” 2.00” 809-22-1875 $41.44 809-E-22-1875 $47.69 809C-22-1875 $47.69

.250” .250” .250” .125” .250” 2.00” 809-22-2500 $41.44 809-E-22-2500 $47.69 809C-22-2500 $47.69

.3125” .0156” .250” .157” .375” 2.00” 809-30-0156 $55.40 809-E-30-0156 $62.69 809C-30-0156 $62.69

.3125” .0312” .250” .157” .375” 2.00” 809-30-0312 $55.40 809-E-30-0312 $62.69 809C-30-0312 $62.69

.3125” .0394” .250” .157” .375” 2.00” 809-30-0394 $55.40 809-E-30-0394 $62.69 809C-30-0394 $62.69

.3125” .0469” .250” .157” .375” 2.00” 809-30-0469 $55.40 809-E-30-0469 $62.69 809C-30-0469 $62.69

.3125” .0625” .250” .157” .375” 2.00” 809-30-0625 $55.40 809-E-30-0625 $62.69 809C-30-0625 $62.69

.3125” .0787” .250” .157” .375” 2.00” 809-30-0787 $55.40 809-E-30-0787 $62.69 809C-30-0787 $62.69

.3125” .0937” .250” .157” .375” 2.00” 809-30-0937 $55.40 809-E-30-0937 $62.69 809C-30-0937 $62.69

.375” .0156” .250” .188” .375” 2.00” 809-31-0156 $64.45 809-E-31-0156 $72.79 809C-31-0156 $72.79

.375” .0312” .250” .188” .375” 2.00” 809-31-0312 $62.16 809-E-31-0312 $70.50 809C-31-0312 $70.50

.375” .0394” .250” .188” .375” 2.00” 809-31-0394 $62.16 809-E-31-0394 $70.50 809C-31-0394 $70.50

.375” .0469” .250” .188” .375” 2.00” 809-31-0469 $62.16 809-E-31-0469 $70.50 809C-31-0469 $70.50

.375” .0625” .250” .188” .375” 2.00” 809-31-0625 $62.16 809-E-31-0625 $70.50 809C-31-0625 $70.50

.375” .0787” .250” .188” .375” 2.00” 809-31-0787 $62.16 809-E-31-0787 $70.50 809C-31-0787 $70.50

.375” .0937” .250” .188” .375” 2.00” 809-31-0937 $62.16 809-E-31-0937 $70.50 809C-31-0937 $70.50

.375” .125” .250” .188” .375” 2.00” 809-31-1250 $62.16 809-E-31-1250 $70.50 809C-31-1250 $70.50

BALL END, STANDARD & STUB, CVD COATED DECIMAL .015” -.093”

18

• Use: Graphites / Composites • Rake Angle: Positive• Extended Tool Life • Center Cutting: Yes• Helix: 30 Degrees • Crystalline Diamond Coated• Hand: RHS/ RHC • Diameter Tolerance: +/-0.001

Diameter Flute Length Shank Diameter Overall length CVD Coated(Ø) (FL) (SØ) (OAL) 4 Flute Price

.015” .045” .125” 1.50” 883-CVD-.015 $75.80

.020” .060” .125” 1.50” 883-CVD-.020 $75.80

.031” (1/32”) .093” .125” 1.50” 883-CVD-.031 $75.80

.047” (3/64”) .141” .125” 1.50” 883-CVD-.047 $75.80

.062” (1/62”) .1875” .125” 1.50” 883-CVD-.062 $71.75

.093” (3/32”) .279” .125” 1.50” 883-CVD-.093 $71.75

Diameter Flute Length Shank Diameter Overall Length CVD Coated(Ø) (FL) (SØ) (OAL) 3 Flute Price

.015” .023” .125” 2.50” 888XB-CVD-.015 $84.86

.020” .030” .125” 2.50” 888XB-CVD-.020 $84.86

.031” .047” .125” 2.50” 888XB-CVD-.031 $84.86

.047” .071” .125” 2.50” 888XB-CVD-.047 $84.86

.062” .093” .125” 2.50” 888XB-CVD-.062 $80.80

.093” .140” .125” 2.50” 888XB-CVD-.093 $80.80

Standard

Long Shank, Stub

SØ Ø

FLOAL

• Hand: RHS/ RHC • Uncoated for General Purpose • Helix: 35° • ALTIN for High Performance • Rake Angle: Positive • Amorphous Diamond for Graphites, Composites • Center cutting: Yes • Diameter Tolerance: +0.000/-.001

BALL END, LONG FLUTEFRACTIONAL 1/64” -1/2”

19

• Hand: RHS/ RHC • Uncoated for General Purpose • Helix: 35° • ALTIN for High Performance • Rake Angle: Positive • Amorphous Diamond for Graphites, Composites • Center cutting: Yes • Diameter Tolerance: +0.000/-.001

• Helix: 30 Degrees • Diameter Tolerance: +0.000/-.002

Diameter Flute Length Shank Diameter

OverallLength Uncoated ALTIN Coated Amorphous Diamond

(Ø) (FL) (SØ) (OAL) 3 Flute Price 3 Flute Price 3-Flute Price1/64” .078” .125” 2.50” 3-0156B $33.63 3-0156B-E $39.75 AD3-0156B $44.56

1/32” .156” .125” 2.50” 3-0312B $26.45 3-0312B-E $30.62 AD3-0312B $37.38

3/64” .250” .125” 2.50” 3-0469B $25.71 3-0469B-E $31.84 AD3-0469B $36.66

1/16” .500” .125” 2.50” 3-0625B $26.34 3-0625B-E $32.47 AD3-0625B $37.28

5/64” .500” .125” 2.50” 3-0781B $23.53 3-0781B-E $27.70 AD3-0781B $34.46

3/32” .750” .125” 2.50” 3-0938B $26.34 3-0938B-E $30.51 AD3-0938B $37.28

1/8” 1.000” .125” 2.50” 3-1250B $24.06 3-1250B-E $28.22 AD3-1250B $34.99

Diameter Flute Length Shank Diameter

OverallLength Uncoated ALTIN Coated Amorphous Diamond

(Ø) (FL) (SØ) (OAL) 4 Flute Price 4 Flute Price 4-Flute Price1/8” .750” .125” 2.25” 17301 $22.63 -- --

1/8” 1.000” .125” 3.00” 17302 $25.31 -- -

3/16” .750” .1875” 2.50” 17303 $26.04 -- --

3/16” 1.125” .1875” 3.00” 17304 $25.71 17304-E $30.20 AD4-1875B $40.81

1/4” 1.125” .250” 3.00” 17305 $36.59 -- --

1/4” 1.000” .250” 4.00” 17306 $40.37 -- --

1/4” 1.500” .250” 4.00” 17307 $28.95 17307-E $36.24 AD4-2500B $46.13

1/4” 1.500” .250” 6.00” 17308 $45.20 -- -

5/16” 1.125” .3125” 3.00” 17309 $43.00 -- --

5/16” 1.625” .3125” 4.00” 17310 $39.56 17310-E $46.86 AD17310 $72.63

3/8” 1.125” .375” 3.00” 17311 $49.61 -- --

3/8” 1.000” .375” 4.00” 17312 $60.80 -- --

3/8” 1.750” .375” 4.00” 17313 $49.88 17313-E $58.21 AD17313 $82.94

3/8” 1.500” .375” 6.00” 17314 $81.48 -- --

1/2” 2.000” .500” 4.00” 17318 $61.75 17318-E $73.21 --

3 Flute G Mills

4 Flute

DOUBLE-END PLAIN TYPE

20

KEO Plain Type combined drill and countersinks are used for producing center holes in components or workpieces which require machining between centers.

Also available with titanium-nitride coating or in a 5-piece set.

A B C D

Size BodyDia.

PointDia.

Point Length OAL HSS Price HSS-TiN Price HSS-LH Price CO Price T15 Price

#5-0 1/8 0.010 0.010 1-1/4 10010 $8.57 10010-TiN $9.55 10013 $31.99 10012 $33.70 10011 $50.57

#4-0 1/8 0.015 0.015 1-1/4 10015 $7.87 10015-TiN $8.86 10018 $31.99 10017 $32.75 10016 $49.16

#3-0 1/8 0.020 0.020 1-1/4 10020 $7.45 10020-TiN $8.46 10023 $20.16 10022 $22.25 10021 $33.40

#2-0 1/8 0.025 0.025 1-1/4 10025 $7.45 10025-TiN $8.46 10028 $20.16 10027 $22.25 10026 $33.40

#0 1/8 1/32 1/32 1-1/4 10032 $7.45 10032-TiN $8.46 10035 $20.16 10034 $22.25 10033 $33.40

#1 1/8 3/64 3/64 1-1/4 10100 $5.20 10100-TiN $6.19 10150 $11.09 10142 $12.05 10115 $17.92

#2 3/16 5/64 5/64 1-7/8 10200 $5.43 10200-TiN $6.83 10250 $11.32 10242 $12.44 10215 $18.43

#3 1/4 7/64 7/64 2 10300 $5.66 10300-TiN $7.56 10350 $11.62 10342 $12.85 10315 $18.93

#4 5/16 1/8 1/8 2-1/8 10400 $5.83 10400-TiN $9.04 10450 $11.96 10442 $13.39 10415 $19.10

#4-1/2 3/8 9/64 9/64 2-1/2 14500 $8.04 14500-TiN $11.24 14550 $16.73 10452 $19.90 14515 $25.13

#5 7/16 3/16 3/16 2-3/4 10500 $9.25 10500-TiN $14.35 10550 $18.20 10542 $21.10 10515 $30.01

#6 1/2 7/32 7/32 3 10600 $13.91 10600-TiN $19.02 10650 $26.41 10642 $32.73 10615 $46.29

#7 5/8 1/4 1/4 3-1/4 10700 $21.10 10700-TiN $29.13 10750 $36.68 10742 $49.25 10715 $68.75

#8 3/4 5/16 5/16 3-1/2 10800 $28.99 10800-TiN $38.12 10850 $49.65 10842 $69.73 10815 $99.72

#9 7/8 11/32 11/32 3-5/8 10900 $52.59 10900-TiN $65.14 10950 $91.27 10942 $129.10 10915 $185.61

#10 1 3/8 3/8 3/8 11000 $69.03 11000-TiN $85.01 11050 $119.81 11042 $169.51 11015 $243.69

Tolerances High LowOAL +1/32 -1/16

Point Ø +0.003 -0.0

Point Length

Point Ø < 1/32 +0.005 -0.005

1/32 ≤ Point Ø ≤ 5/64 +0.008 -0.008

Point > 5/64 +1/64 -1/64

CS Angle +1° -1°

Body Ø +0.0 -0.002

Product numbers 10010, 10015, 10020, 10025, 10032, 10100, 10200, 10300, 10400, 10500, 10600, and 10700 are sold in packs of 12Product number 10800 is sold in packs of 6Product numbers 10900 and 11000 are sold in packs of 3All dimensions in inches. Many tools are available with additional coatings.Please call for quote.

HSS Cobalt Aircraft 60° Countersink Angle

CountersinkAngle

A

C

D

B

118°+2°-0°[ ]

DOUBLE-END PLAIN TYPE

21

A B C D

Size BodyDia.

PointDia.

PointLength OAL HSS Price HSS-TiN Price

#5-0 1/8 0.010 0.010 1-1/4 10038 $28.04 10038-TiN $30.57

#4-0 1/8 0.015 0.015 1-1/4 10039 $28.04 10039-TiN $30.57

#3-0 1/8 0.020 0.020 1-1/4 10040 $17.97 10040-TiN $19.93

#2-0 1/8 0.025 0.025 1-1/4 10029 $18.96 10029-TiN $19.93

#0 1/8 1/32 1/32 1-1/4 10036 $18.96 10036-TiN $19.93

#1 1/8 3/64 3/64 1-1/4 10182 $8.50 10182-TiN $9.46

#2 3/16 5/64 5/64 1-7/8 10282 $8.70 10282-TiN $10.11

#3 1/4 7/64 7/64 2 10382 $9.00 10382-TiN $10.87

#4 5/16 1/8 1/8 2-1/8 10482 $9.36 10482-TiN $12.48

#4-1/2 3/8 9/64 9/64 2-1/2 14582 $12.81 14582-TiN $15.95

#5 7/16 3/16 3/16 2-3/4 10582 $14.27 10582-TiN $19.25

#6 1/2 7/32 7/32 3 10682 $21.59 10682-TiN $26.58

#7 5/8 1/4 1/4 3-1/4 10782 $30.56 10782-TiN $38.39

#8 3/4 5/16 5/16 3-1/2 10882 $42.85 10882-TiN $51.75

#9 7/8 11/32 11/32 3-5/8 10982 $79.03 10982-TiN $91.27

#10 1 3/8 3/8 3/8 11082 $103.97 11082-TiN $119.56

A B C D

Size Body Dia.

Point Dia.

PointLength OAL HSS Price HSS-TiN Price

#5-0 1/8 0.010 0.010 1-1/4 10014 $29.60 10014-TiN $30.57

#4-0 1/8 0.015 0.015 1-1/4 10019 $29.60 10019-TiN $30.57

#3-0 1/8 0.020 0.020 1-1/4 10024 $18.96 10024-TiN $19.93

#2-0 1/8 0.025 0.025 1-1/4 10030 $18.96 10030-TiN $19.93

#0 1/8 1/32 1/32 1-1/4 10037 $18.96 10037-TiN $19.93

#1 1/8 3/64 3/64 1-1/4 10190 $8.50 10190-TiN $9.46

#2 3/16 5/64 5/64 1-7/8 10290 $8.70 10290-TiN $10.09

#3 1/4 7/64 7/64 2 10390 $9.00 10390-TiN $10.85

#4 5/16 1/8 1/8 2-1/8 10490 $9.36 10490-TiN $12.48

#4-1/2 3/8 9/64 9/64 2-1/2 14590 $12.81 14590-TiN $15.94

#5 7/16 3/16 3/16 2-3/4 10590 $14.27 10590-TiN $19.24

#6 1/2 7/32 7/32 3 10690 $21.59 10690-TiN $26.58

#7 5/8 1/4 1/4 3-1/4 10790 $30.56 10790-TiN $38.39

#8 3/4 5/16 5/16 3-1/2 10890 $42.85 10890-TiN $51.75

#9 7/8 11/32 11/32 3-5/8 10990 $79.03 10990-TiN $91.27

#10 1 3/8 3/8 3/8 11090 $103.97 11090-TiN $119.56

Tolerances High LowOAL +1/32 -1/16

Point Ø +0.003 -0.0

Point Length

Point Ø < 1/32 +0.005 -0.005

1/32 ≤ Point Ø ≤ 5/64 +0.008 -0.008

Point > 5/64 +1/64 -1/64

CS Angle +1° -1°

Body Ø +0.0 -0.002

Product numbers 10014, 10019, 10024, 10030, 10037, 10190, 10290, 10390, 10490, 10590,10690, and 10790 are sold in packs of 12Product number 10890 is sold in packs of 6Product numbers 10990 and 11090 are sold in packs of 3All dimensions in inches. Many tools are available with additional coatings. Please call for quote.

HSS Aircraft 82° Countersink Angle

HSS Aircraft 90° Countersink Angle

CountersinkAngle

A

C

D

B

118°+2°-0°[ ]

DOUBLE-END LONG SERIES

22

KEO Long Series combined drill and countersinks are used for producing center holes in components or workpieces wih the extra length allowing access to difficult-to-reach areas.

A B C D

Size BodyDia.

PointDia.

Point Length OAL HSS

60° Price

#1 x 8 1/8 3/64 3/64 8 21080 $31.57

#2 x 8 3/16 5/64 5/64 8 22080 $32.03

#3 x 8 1/4 7/64 7/64 8 23080 $32.41

#4 x 8 5/16 1/8 1/8 8 24080 $32.98

#4-1/2 x 8 3/8 9/64 9/64 8 24580 $34.10

#5 x 8 7/16 3/16 3/16 8 25080 $35.52

#6 x 8 1/2 7/32 7/32 8 26080 $41.08

#7 x 8 5/8 1/4 1/4 8 27080 $74.52

#8 x 8 3/4 5/16 5/16 8 28080 $82.68

All dimensions in inches

A B C D

Size BodyDia.

PointDia.

Point Length OAL HSS

60° Price HSS-TiN Price HSS82° Price HSS

90° Price CO60° Price

#1 x 3 1/8 3/64 3/64 3 21030 $12.56 21030-TiN $13.86 21033 $19.42 21034 $19.42 21032 $37.71

#1 x 4 1/8 3/64 3/64 4 21040 $13.11 21040-TiN $14.40 21043 $22.06 21044 $22.06 21042 $38.99

#1 x 5 1/8 3/64 3/64 5 21050 $18.21 21050-TiN $19.51 21053 $30.65 21054 $30.65 21052 $54.25

#1x 6 1/8 3/64 3/64 6 21060 $23.85 21060-TiN $26.12 21063 $40.11 21064 $40.11 21062 $70.89

#2 x 3 3/16 5/64 5/64 3 22030 $12.71 22030-TiN $14.45 22033 $21.32 22034 $21.32 22032 $37.81

#2 x 4 3/16 5/64 5/64 4 22040 $14.37 22040-TiN $16.10 22043 $24.13 22044 $24.13 22042 $42.74

#2 x 5 3/16 5/64 5/64 5 22050 $18.41 22050-TiN $20.13 22053 $30.65 22054 $30.65 22052 $54.79

#2 x 6 3/16 5/64 5/64 6 22060 $23.94 22060-TiN $27.10 22063 $40.29 22064 $40.29 22062 $71.33

#3 x 3 1/4 7/64 7/64 3 23030 $13.27 23030-TiN $15.83 23033 $22.30 23034 $22.30 23032 $39.42

#3 x 4 1/4 7/64 7/64 4 23040 $15.14 23040-TiN $18.32 23043 $25.44 23044 $25.44 23042 $44.94

#3 x 5 1/4 7/64 7/64 5 23050 $19.91 23050-TiN $23.76 23053 $33.51 23054 $33.51 23052 $59.29

#3 x 6 1/4 7/64 7/64 6 23060 $24.16 23060-TiN $28.65 23063 $40.57 23064 $40.57 23062 $71.89

#4 x 3 5/16 1/8 1/8 3 24030 $15.88 24030-TiN $18.76 24033 $26.15 24034 $26.15 24032 $46.31

#4 x 4 5/16 1/8 1/8 4 24040 $16.77 24040-TiN $20.74 24043 $28.22 24044 $28.22 24042 $49.92

#4 x 5 5/16 1/8 1/8 5 24050 $21.44 24050-TiN $26.22 24053 $36.04 24054 $36.04 24052 $63.78

#4 x 6 5/16 1/8 1/8 6 24060 $24.75 24060-TiN $30.31 24063 $41.66 24064 $41.66 24062 $73.63

Product numbers 21030, 21040, 21050, 21060, 22030, 22040, 22050, 22060, 23030, 23040, 23050, 23060, 24030, 24040, 24050, and 24060 are sold in packs of 12

All dimensions in inches. Many tools are available with additional coatings. Please call for quote.

HSS Long Series 8”

HSS Cobalt Long Series

Countersink Angle

A

C

D

B

118°+2°-0°[ ]

KEO NC SPOTTING DRILLS

23

KEO NC Spotting Drills are designed with a narrow chisel edge for quick starting and a constant web to allow for resharpening without the need for web thinning.

A B CBodyDia.

Flute Length OAL HSS

90° Price HSS-TiN 90° Price CO

90° Price HSS 120° Price HSS-TiN

120° Price CO120° Price

1/4 3/4 2-1/2 32140 $24.74 32140-TiN $27.22 32143 $28.00 33140 $24.74 33140-TiN $27.22 33143 $28.00

1/4 3/4 4 32142 $35.61 32142-TiN $38.70 32145 $40.30 33142 $35.61 33142-TiN $38.70 33145 $40.30

1/4 3/4 6 32144 $48.90 32144-TiN $53.25 32147 $55.35 33144 $48.90 33144-TiN $53.25 33147 $55.35

3/8 1-1/8 3-1/8 32380 $26.71 32380-TiN $30.58 32383 $30.24 33380 $26.71 33380-TiN $30.58 33383 $30.24

3/8 1-1/8 5 32382 $37.96 32382-TiN $42.63 32385 $42.97 33382 $37.96 33382-TiN $42.63 33385 $42.97

3/8 1-1/8 7 32384 $52.60 32384-TiN $58.78 32387 $59.52 33384 $52.60 33384-TiN $58.78 33387 $59.52

1/2 1-3/8 3-3/4 32120 $34.24 32120-TiN $39.19 32123 $38.76 33120 $34.24 33120-TiN $39.19 33123 $38.76

1/2 1-3/8 6 32122 $47.48 32122-TiN $56.15 32125 $53.73 33122 $47.48 33122-TiN $56.15 33125 $53.73

1/2 1-3/8 8 32124 $64.56 32124-TiN $75.72 32127 $73.08 33124 $64.56 33124-TiN $75.72 33127 $73.08

5/8 1-5/8 4-3/8 32580 $44.57 32580-TiN $53.88 32583 $50.44 33580 $44.57 33580-TiN $53.88 33583 $50.44

5/8 1-5/8 7 32582 $60.00 32582-TiN $72.39 32585 $67.91 33582 $60.00 33582-TiN $72.39 33585 $67.91

5/8 1-5/8 9 32584 $82.95 32584-TiN $98.40 32587 $93.88 33584 $82.95 33584-TiN $98.40 33587 $93.88

3/4 1-7/8 5 32340 $60.98 32340-TiN $71.58 32343 $69.00 33340 $60.98 33340-TiN $71.58 33343 $69.00

3/4 1-7/8 8 32342 $82.43 32342-TiN $98.30 32345 $93.29 33342 $82.43 33342-TiN $98.30 33345 $93.29

3/4 1-7/8 10 32344 $110.17 32344-TiN $129.59 32347 $124.68 33344 $110.17 33344-TiN $129.59 33347 $124.68

1 2-1/4 6 32100 $104.90 32100-TiN $126.55 32103 $118.71 33100 $104.90 33100-TiN $126.55 33103 $118.71

1 2-1/4 8 32102 $111.65 32102-TiN $139.48 32105 $126.36 33102 $111.65 33102-TiN $139.48 33105 $126.36

1 2-1/4 10 32104 $137.41 32104-TiN $171.44 32107 $155.50 33104 $137.41 33104-TiN $171.44 33107 $155.50

A B CBodyDia.

Flute Length OAL HSS Price CO Price

1/4 3/4 2-1/2 38142 $23.64 38143 $28.00

1/4 3/4 4 38144 $34.01 38145 $40.30

1/4 3/4 6 38146 $46.61 38147 $55.35

3/8 1-1/8 3-1/8 38382 $25.51 38383 $30.24

3/8 1-1/8 5 38384 $36.25 38385 $42.97

3/8 1-1/8 7 38386 $50.24 38387 $59.52

1/2 1-3/8 3-3/4 38122 $32.71 38123 $38.76

1/2 1-3/8 6 38124 $45.35 38125 $53.73

1/2 1-3/8 8 38126 $61.67 38127 $73.08

5/8 1-5/8 4-3/8 38582 $42.57 38583 $50.44

5/8 1-5/8 7 38584 $57.31 38585 $67.91

5/8 1-5/8 9 38586 $79.23 38587 $93.88

3/4 1-7/8 5 38342 $58.24 38343 $69.00

3/4 1-7/8 8 38344 $78.73 38345 $93.29

3/4 1-7/8 10 38346 $105.23 38347 $124.68

1 2-1/4 6 38102 $100.18 38103 $118.71

1 2-1/4 8 38104 $106.64 38105 $126.36

1 2-1/4 10 38106 $131.24 38107 $155.50



HSS Cobalt 82° Countersink Angle

HSS Cobalt 90° and 120° Point Angle

A

C

B

82°90°

or 120°

CHAMFER MILLS DOUBLE-END 2 & 4 FLUTE

24

KEO’s Chamfer Mills in 2 and 4 Flute are designed for deburring and chamfering. The 4 Flute Chamfer Mills improve tool life and finish for profiling and chamfering.

All dimensions in inches. Many tools are available with additional coatings.Please call for quote.


• General purpose

• End Shape: 60°, 82°, 90°, 100°, or 120°

• Cutter Type: Chamfer Mill

• 2 and 4 Flute

• Solid Carbide

• Double End

4 Flute

A BBodyDia. OAL Flutes End 60° Price 82° Price 90° Price 100° Price 120° Price

1/8 2 2 DE 42226 $24.92 42228 $24.92 42229 $24.92 42220 $24.92 42222 $24.92

3/16 2-1/2 2 DE 42236 $29.92 42238 $29.92 42239 $29.92 42230 $29.92 42232 $29.92

1/4 2-1/2 2 DE 42246 $37.27 42248 $37.27 42249 $37.27 42240 $37.27 42242 $37.27

5/16 2-1/2 2 DE 42256 $47.68 42258 $47.68 42259 $47.68 42250 $47.68 42252 $47.68

3/8 2-1/2 2 DE 42266 $58.12 42268 $58.12 42269 $58.12 42260 $58.12 42262 $58.12

1/2 3 2 DE 42286 $96.42 42288 $96.42 42289 $96.42 42280 $96.42 42282 $96.42

A BBodyDia. OAL Flutes End 60° Price 82° Price 90° Price 100° Price 120° Price

1/8 2 4 DE 42426 $24.92 42428 $24.92 42429 $24.92 42420 $24.92 42422 $24.92

3/16 2-1/2 4 DE 42436 $29.92 42438 $29.92 42439 $29.92 42430 $29.92 42432 $29.92

1/4 2-1/2 4 DE 42446 $37.27 42448 $37.27 42449 $37.27 42440 $37.27 42442 $37.27

5/16 2-1/2 4 DE 42456 $47.68 42458 $47.68 42459 $47.68 42450 $47.68 42452 $47.68

3/8 2-1/2 4 DE 42466 $58.12 42468 $58.12 42469 $58.12 42460 $58.12 42462 $58.12

1/2 3 4 DE 42486 $96.42 42488 $96.42 42489 $96.42 42480 $96.42 42482 $96.42

Carbide 60°, 82°, 90°, 100°, and 120° included Angles


B

A Included Angle

B

A Included Angle

2 Flute

DRILL MILLS SINGLE-END 4 FLUTE

25



KEO’s Drill Mill are offered in both 2 and 4 Flutes. Drill Mills are used in a variety of applications such as chamfering, milling, drilling, countersinking and spotting.


• Used for chamfering, milling and some spotting applications

• End Shape: 60° and 90° drill point

• Cutter Type: Drill Mill

• 4 Flute

• Solid Carbide

4 Flute / Single End

A B C

CutDia.

ShankDia. OAL LOC Flutes 60° Price 90° Price

1/32 1/8 1-1/2 1/8 4 44016 $19.70 44019 $19.70

1/16 1/8 1-1/2 3/16 4 44026 $19.70 44029 $19.70

3/32 1/8 1-1/2 3/8 4 44036 $19.70 44039 $19.70

1/8 1/8 1-1/2 1/2 4 44046 $19.70 44049 $19.70

3/1 3/16 2 5/8 4 44066 $20.87 44069 $20.87

1/4 1/4 2-1/2 3/4 4 44086 $22.60 44089 $22.60

5/16 5/16 2-1/2 13/16 4 44106 $23.87 44109 $23.87

3/8 3/8 2-1/2 1 4 44126 $29.81 44129 $29.81

7/16 7/16 2-3/4 1 4 44146 $39.63 44149 $39.63

1/2 1/2 3 1 4 44166 $46.67 44169 $46.67

5/8 5/8 3-1/2 1-1/4 4 44206 $90.59 44209 $90.59

3/4 3/4 4 1-1/2 4 44246 $131.75 44249 $131.75

Carbide 60° and 90° Point Angles

C

B APointAngle

SINGLE-FLUTE COBALT COUNTERSINKS

26

Product Numbers 55400, 55402, and 55403, are sold in packs of 12Product Numbers 55404, 55405, and 55406 are sold in packs of 6All dimensions in inches. Many tools are available with additional coatings.Please call for quote.

Product Numbers 55412, 55413, 55414, and 55415 are sold in packs of 12Product Numbers 55416, 55417, and 55418 are sold in packs of 6All dimensions in inches. Many tools are available with additional coatings.Please call for quote.


A B C DBodyDia. OAL Shank

Dia.ShankLength CO Price CO-TiN Price

1/8 1-1/4 1/8 N/A 55400 $9.61 55400-TiN $10.71

3/16 1-3/8 3/16 N/A 55401 $9.85 55401-TiN $11.45

1/4 1-1/2 1/4 N/A 55402 $10.25 55402-TiN $12.39

3/8 1-3/4 1/4 7/8 55403 $11.69 55403-TiN $14.39

1/2 2 1/4 1 55404 $14.31 55404-TiN $18.64

5/8 2-1/4 3/8 1 55405 $19.13 55405-TiN $26.31

3/4 2-5/8 1/2 1-1/4 55406 $27.92 55406-TiN $36.18

1 2-3/4 1/2 1-1/4 55407 $47.89 55407-TiN $62.26

1-1/4 3 1/2 1-1/4 55408 $93.75 55408-TiN $110.97

1-1/2 3-1/4 3/4 1-1/4 55409 $126.94 55409-TiN $153.87

1-3/4 3-1/2 3/4 1-1/4 55410 $162.06 55410-TiN $205.14

2 3-3/4 3/4 1-1/4 55411 $226.81 55411-TiN $269.89



1/8 1-1/4 1/8 N/A 55412 $9.61 55412-TiN $10.71

3/16 1-3/8 3/16 N/A 55413 $9.85 55413-TiN $11.45

1/4 1-1/2 1/4 N/A 55414 $10.25 55414-TiN $12.39

3/8 1-3/4 1/4 7/8 55415 $11.69 55415-TiN $14.39

1/2 2 1/4 1 55416 $14.31 55416-TiN $18.64

5/8 2-1/4 3/8 1 55417 $19.13 55417-TiN $26.31

3/4 2-5/8 1/2 1-1/4 55418 $27.92 55418-TiN $36.18

1 2-3/4 1/2 1-1/4 55419 $47.89 55419-TiN $62.26

1-1/4 2-3/4 1/2 1-1/4 55420 $93.75 55420-TiN $110.97

1-1/2 2-7/8 3/4 1-1/4 55421 $126.94 55421-TiN $153.87

1-3/4 3 3/4 1-1/4 55422 $162.06 55422-TiN $205.14

2 3-1/4 3/4 1-1/4 55423 $226.81 55423-TiN $269.89



1/8 1-1/4 1/8 N/A 55424 $9.61 55424-TiN $10.71

3/16 1-3/8 3/16 N/A 55425 $9.85 55425-TiN $11.45

1/4 1-1/2 1/4 N/A 55426 $10.25 55426-TiN $12.39

3/8 1-3/4 1/4 7/8 55427 $11.69 55427-TiN $14.39

1/2 2 1/4 1 55428 $14.31 55428-TiN $18.64

5/8 2-1/4 3/8 1 55429 $19.13 55429-TiN $26.31

3/4 2-5/8 1/2 1-1/4 55430 $27.92 55430-TiN $36.18

1 2-3/4 1/2 1-1/4 55431 $47.89 55431-TiN $62.26

1-1/4 2-3/4 1/2 1-1/4 55432 $93.75 55432-TiN $110.97

1-1/2 2-7/8 3/4 1-1/4 55433 $126.94 55433-TiN $153.87

1-3/4 3 3/4 1-1/4 55434 $162.06 55434-TiN $205.14

2 3-1/4 3/4 1-1/4 55435 $226.81 55435-TiN $269.89

Cobalt 60° Countersink Angle

Cobalt 82° Countersink Angle Cobalt 90° Countersink Angle

C

D

B

A

CountersinkAngle

SINGLE FLUTE COBALT COUNTERSINKS

27






1/8 1-1/4 1/8 N/A 55436 $9.61 55436-TiN $10.71

3/16 1-3/8 3/16 N/A 55437 $9.85 55437-TiN $11.45

1/4 1-1/2 1/4 N/A 55438 $10.25 55438-TiN $12.39

3/8 1-3/4 1/4 7/8 55439 $11.69 55439-TiN $14.39

1/2 2 1/4 1 55440 $14.31 55440-TiN $18.64

5/8 2-1/4 3/8 1 55441 $19.13 55441-TiN $26.31

3/4 2-5/8 1/2 1-1/4 55442 $27.92 55442-TiN $36.18

1 2-3/4 1/2 1-1/4 55443 $47.89 55443-TiN $62.26

1-1/4 2-3/4 1/2 1-1/4 55444 $93.75 55444-TiN $110.97

1-1/2 2-7/8 3/4 1-1/4 55445 $126.94 55445-TiN $153.87

1-3/4 3 3/4 1-1/4 55446 $162.06 55446-TiN $205.14

2 3-1/4 3/4 1-1/4 55447 $226.81 55447-TiN $269.89



1/8 1-1/4 1/8 N/A 55448 $9.61 55448-TiN $10.71

3/16 1-3/8 3/16 N/A 55449 $9.85 55449-TiN $11.45

1/4 1-1/2 1/4 N/A 55450 $10.25 55450-TiN $12.39

3/8 1-3/4 1/4 7/8 55451 $11.69 55451-TiN $14.39

1/2 2 1/4 1 55452 $14.31 55452-TiN $18.64

5/8 2-1/4 3/8 1 55453 $19.13 55453-TiN $26.31

3/4 2-5/8 1/2 1-1/4 55454 $27.92 55454-TiN $36.18

1 2-3/4 1/2 1-1/4 55455 $47.89 55455-TiN $62.26

1-1/4 2-3/4 1/2 1-1/4 55456 $93.75 55456-TiN $110.97

1-1/2 2-7/8 3/4 1-1/4 55457 $126.94 55457-TiN $153.87

1-3/4 3 3/4 1-1/4 55458 $162.06 55458-TiN $205.14

2 3-1/4 3/4 1-1/4 55459 $226.81 55459-TiN $269.89



1/8 1-1/4 1/8 N/A 55460 $9.61 55460-TiN $10.71

3/16 1-3/8 3/16 N/A 55461 $9.85 55461-TiN $11.45

1/4 1-1/2 1/4 N/A 55462 $10.25 55462-TiN $12.39

3/8 1-3/4 1/4 7/8 55463 $11.69 55463-TiN $14.39

1/2 2 1/4 1 55464 $14.31 55464-TiN $18.64

5/8 2-1/4 3/8 1 55465 $19.13 55465-TiN $26.31

3/4 2-5/8 1/2 1-1/4 55466 $27.92 55466-TiN $36.18

1 2-3/4 1/2 1-1/4 55467 $47.89 55467-TiN $62.26

1-1/4 2-3/4 1/2 1-1/4 55468 $93.75 55468-TiN $110.97

1-1/2 2-7/8 3/4 1-1/4 55469 $126.94 55469-TiN $153.87

1-3/4 3 3/4 1-1/4 55470 $162.06 55470-TiN $205.14

2 3-1/4 3/4 1-1/4 55471 $226.81 55471-TiN $269.89




C

D

B

A

CountersinkAngle

6-FLUTE COUNTERSINKS

28

KEO 6-Flute line of countersinks are companions to our Single Flute Countersinks and our 3 and 4-Flute Center Reamer line.

As a rule, the more edges per revolution, the greater amount of material that may be removed. We have designed the 6-Flute tools with staggered cutting edges.

A B C D EBodyDia. OAL Shank

Dia.ShankLength

NoseDia. HSS Price HSS-TiN Price

1/8 1-1/4 1/8 N/A 0.025 55040 $7.67 55040-TiN $8.67

3/16 1-3/8 3/16 N/A 1/32 55041 $8.37 55041-TiN $9.83

1/4 1-1/2 1/4 N/A 3/64 55042 $8.52 55042-TiN $10.46

5/16 1-3/4 1/4 7/8 1/16 55043 $10.06 55043-TiN $12.54

3/8 1-3/4 1/4 7/8 5/64 55044 $10.52 55044-TiN $12.97

1/2 2 1/4 1 7/64 55045 $12.93 55045-TiN $16.86

1/2 2 3/8 1 7/64 55046 $12.93 55046-TiN $16.86

5/8 2-1/4 1/4 1 1/8 55047 $18.75 55047-TiN $25.27

5/8 2-1/4 3/8 1 1/8 55048 $18.75 55048-TiN $25.27

3/4 2-5/8 1/2 1-1/4 5/32 55049 $25.71 55049-TiN $33.20

7/8 2-3/4 1/2 1-1/4 11/64 55050 $36.38 55050-TiN $46.64

1 2-3/4 1/2 1-1/4 13/64 55051 $40.47 55051-TiN $53.51

1-1/4 2-3/4 1/2 1-1/4 1/4 55052 $62.08 55052-TiN $81.65

1-1/2 2-7/8 3/4 1-1/4 5/16 55053 $88.96 55053-TiN $113.41

1-3/4 3 3/4 1-1/4 23/64 55054 $118.33 55054-TiN $157.43

2 3-1/4 3/4 1-1/4 13/32 55055 $150.46 55055-TiN $189.56

2-1/2 5 1 1-1/2 1/2 55056 $390.03 55056-TiN $458.89

3 5-1/4 1 1-1/2 19/32 55057 $537.57 55057-TiN $692.83


Dia.ShankLength


1/8 1-1/4 1/8 N/A 0.025 55060 $7.67 55060-TiN $8.67

3/16 1-3/8 3/16 N/A 1/32 55061 $8.37 55061-TiN $9.83

1/4 1-1/2 1/4 N/A 3/64 55062 $8.52 55062-TiN $10.46

5/16 1-3/4 1/4 7/8 1/16 55063 $10.06 55063-TiN $12.54

3/8 1-3/4 1/4 7/8 5/64 55064 $10.52 55064-TiN $12.97

1/2 2 1/4 1 7/64 55065 $12.93 55065-TiN $16.86

1/2 2 3/8 1 7/64 55066 $12.93 55066-TiN $16.86

5/8 2-1/4 1/4 1 1/8 55067 $18.75 55067-TiN $25.27

5/8 2-1/4 3/8 1 1/8 55068 $18.75 55068-TiN $25.27

3/4 2-5/8 1/2 1-1/4 5/32 55069 $25.71 55069-TiN $33.20

7/8 2-3/4 1/2 1-1/4 11/64 55070 $36.38 55070-TiN $46.64

1 2-3/4 1/2 1-1/4 13/64 55071 $40.47 55071-TiN $53.51

1-1/4 2-3/4 1/2 1-1/4 1/4 55072 $62.08 55072-TiN $81.65

1-1/2 2-7/8 3/4 1-1/4 5/16 55073 $88.96 55073-TiN $113.41

1-3/4 3 3/4 1-1/4 23/64 55074 $118.33 55074-TiN $157.43

2 3-1/4 3/4 1-1/4 13/32 55075 $150.46 55075-TiN $189.56

2-1/2 5 1 1-1/2 1/2 55076 $390.03 55076-TiN $458.89

3 5-1/4 1 1-1/2 19/32 55077 $537.57 55077-TiN $692.83

All dimensions in inches. Many tools are available with additional coatings. Please call for quote.Continues on next page

HSS 90° Countersink Angle


D

B

CA E

CountersinkAngle

6-FLUTE COUNTERSINKS

29

KEO 6-Flute line of countersinks are companions to our Single Flute Countersinks and our 3 and 4-Flute Center Reamer line.

As a rule, the more edges per revolution, the greater amount of material that may be removed. We have designed the 6-Flute tools with staggered cutting edges.


Dia.ShankLength


1/8 1-1/4 1/8 N/A 0.020 55080 $7.67 55080-TiN $8.67

3/16 1-3/8 3/16 N/A 1/32 55081 $8.37 55081-TiN $9.83

1/4 1-1/2 1/4 N/A 3/64 55082 $8.52 55082-TiN $10.46

5/16 1-3/4 1/4 7/8 3/64 55083 $10.06 55083-TiN $12.54

3/8 1-3/4 1/4 7/8 1/16 55084 $10.52 55084-TiN $12.97

1/2 2 1/4 1 5/64 55085 $12.93 55085-TiN $16.86

1/2 2 3/8 1 5/64 55086 $12.93 55086-TiN $16.86

5/8 2-1/4 1/4 1 7/64 55087 $18.75 55087-TiN $25.27

5/8 2-1/4 3/8 1 7/64 55088 $18.75 55088-TiN $25.27

3/4 2-5/8 1/2 1-1/4 1/8 55089 $25.71 55089-TiN $33.20

7/8 2-3/4 1/2 1-1/4 9/64 55090 $36.38 55090-TiN $46.64

1 2-3/4 1/2 1-1/4 11/64 55091 $40.47 55091-TiN $53.51

1-1/4 2-3/4 1/2 1-1/4 7/32 55092 $62.08 55092-TiN $81.65

1-1/2 2-7/8 3/4 1-1/4 1/4 55093 $88.96 55093-TiN $113.41

1-3/4 3 3/4 1-1/4 19/64 55094 $118.33 55094-TiN $157.43

2 3-1/4 3/4 1-1/4 11/32 55095 $150.46 55095-TiN $189.56

2-1/2 5 1 1-1/2 7/16 55096 $390.03 55096-TiN $458.89

3 5-1/4 1 1-1/2 33/64 55097 $537.57 55097-TiN $692.83


Dia.ShankLength


1/8 1-1/4 1/8 N/A 0.020 55100 $7.67 55100-TiN $8.67

3/16 1-3/8 3/16 N/A 1/32 55101 $8.37 55101-TiN $9.83

1/4 1-1/2 1/4 N/A 3/64 55102 $8.52 55102-TiN $10.46

5/16 1-3/4 1/4 7/8 3/64 55103 $10.06 55103-TiN $12.54

3/8 1-3/4 1/4 7/8 1/16 55104 $10.52 55104-TiN $12.97

1/2 2 1/4 1 5/64 55105 $12.93 55105-TiN $16.86

1/2 2 3/8 1 5/64 55106 $12.93 55106-TiN $16.86

5/8 2-1/4 1/4 1 7/64 55107 $18.75 55107-TiN $25.27

5/8 2-1/4 3/8 1 7/64 55108 $18.75 55108-TiN $25.27

3/4 2-5/8 1/2 1-1/4 1/8 55109 $25.71 55109-TiN $33.20

7/8 2-3/4 1/2 1-1/4 9/64 55110 $36.38 55110-TiN $46.64

1 2-3/4 1/2 1-1/4 11/64 55111 $40.47 55111-TiN $53.51

1-1/4 2-3/4 1/2 1-1/4 7/32 55112 $62.08 55112-TiN $81.65

1-1/2 2-7/8 3/4 1-1/4 1/4 55113 $88.96 55113-TiN $113.41

1-3/4 3 3/4 1-1/4 19/64 55114 $118.33 55114-TiN $157.43

2 3-1/4 3/4 1-1/4 11/32 55115 $150.46 55115-TiN $189.56

2-1/2 5 1 1-1/2 7/16 55116 $390.03 55116-TiN $458.89

3 5-1/4 1 1-1/2 33/64 55117 $537.57 55117-TiN $692.83




D

B

CA E

CountersinkAngle

ZERO FLUTE COBALT COUNTERSINKS SPECIALS

30

KEO Flute Countersink & Deburring tools are simple, all-purpose tools made of Cobalt that provide flawless countersinking and deburring. The chatter-free cutting action requires minimal power.

The micro-smooth CNC precision ground construction produces clean, smooth cutting without smearing on a variety of materials. The tool especially excels in countersinking or deburring holes in aluminum, plastics and other nonmetallics.

A B C Dia. of CutHeadDia. OAL Shank

Dia. Min. Max. Uncoated Price TiN Price

5/16 1-7/8 1/4 7/64 9/32 53500 $13.48 53500-TiN $15.89

3/8 1-7/8 1/4 5/32 11/32 53501 $15.40 53501-TiN $17.80

1/2 2 5/16 11/64 29/64 53502 $18.44 53502-TiN $22.30

5/8 2-1/2 3/8 3/16 37/64 53503 $21.17 53503-TiN $27.57

3/4 2-3/4 3/8 1/4 45/64 53504 $32.23 53504-TiN $39.58

1 3 3/8 19/64 27/32 53505 $40.09 53505-TiN $52.89

1-1/4 3-1/2 1/2 27/64 1-1/32 53506 $97.13 53506-TiN $116.33



5/16 1-5/8 1/4 3/32 9/32 53510 $13.48 53510-TiN $15.89

3/8 1-3/4 1/4 9/64 11/32 53511 $15.40 53511-TiN $17.80

1/2 1-3/4 5/16 5/32 29/64 53512 $18.44 53512-TiN $22.30

5/8 2-1/8 3/8 11/64 37/64 53513 $21.17 53513-TiN $27.57

3/4 1-3/8 3/8 13/64 45/64 53514 $32.23 53514-TiN $39.58

1 2-5/8 3/8 19/64 59/64 53515 $40.09 53515-TiN $52.89

1-1/4 3-1/8 1/2 23/64 1-3/32 53516 $97.13 53516-TiN $116.33



5/16 1-5/8 1/4 3/32 9/32 53520 $13.48 53520-TiN $15.89

3/8 1-3/4 1/4 9/64 11/32 53521 $15.40 53521-TiN $17.80

1/2 1-3/4 5/16 5/32 29/64 53522 $18.44 53522-TiN $22.30

5/8 2-1/8 3/8 11/64 37/64 53523 $21.17 53523-TiN $27.57

3/4 1-3/8 3/8 13/64 45/64 53524 $32.23 53524-TiN $39.58

1 2-5/8 3/8 19/64 59/64 53525 $40.09 53525-TiN $52.89

1-1/4 3-1/8 1/2 23/64 1-3/32 53526 $97.13 53526-TiN $116.33



5/16 1-5/8 1/4 3/32 9/32 53530 $13.48 53530-TiN $15.89

3/8 1-3/4 1/4 9/64 11/32 53531 $15.40 53531-TiN $17.80

1/2 1-3/4 5/16 5/32 29/64 53532 $18.44 53532-TiN $22.30

5/8 2-1/8 3/8 11/64 37/64 53533 $21.17 53533-TiN $27.57

3/4 1-3/8 3/8 13/64 45/64 53534 $32.23 53534-TiN $39.58

1 2-5/8 3/8 19/64 59/64 53535 $40.09 53535-TiN $52.89

1-1/4 3-1/8 1/2 23/64 1-1/8 53536 $97.13 53536-TiN $116.33

All dimensions are in inches. Many tools are available with additional coatings.Please call for quote.





B

C

A60°82°90°or

100°

SPECIALS

31

ARCH SPECIALS

Unique tools for unique customers

Most precision tool manufacturers focus on mass-producing standard tools cetered on their own

specific core competency. ARCH Global turns that model on its head. We have put together a group of companies, each serving an industry niche with unique, market-specific expertise. Together, we share best practices, engineering intelligence, and infrastructure to allow us to focus on creating custom-engineered solutions centered on:

• Solid tools • Carbide tools • Indexable tools

• Form tools • Tool holders • Gang tools

• Micro tools • Fixtures • Multi-operation tools

TOOL SETS

32

Jig Bore Combined Drill & Countersink Sets

HSS & Cobalt Single Flute Countersink Sets

Each 5-piece set includes one piece each of the following jig bore type combined drill and countersinks.

Each 5-piece set includes one piece each of 1/4, 3/8, 1/2, 3/4, and 1” body diameter with a partcular included point angle.

C’Drills PointDia.

Product# Price

3/6

1/16

3/32

1/8

5/32

3/16

13000 $121.95

1/2

1/8

3/16

7/32

1/4

9/32

12999 $143.54

PkgQty.

CountersinkAngle

HSSSingle Flute Price CO

Single Flute Price

1 60° 53026 $103.92 50056 $119.52

1 82° 53028 $103.92 50058 $119.52

1 90° 53029 $103.92 50059 $119.52

1 100° 53020 $103.92 50050 $119.52

1 110° 53021 $103.92 50051 $119.52

1 120° 53022 $103.92 50052 $119.52

All dimensions are in inches

Combined Drill & Countersink SetThis 5-piece set includes one piece each of the following plain type combined drill with a standard 60° included countersink angle.

C’Drills PkgQty. HSS Price HSS-TiN Price Cobalt Price Carbide Price

#1

#2

#3

#4

#5

1 10000 $47.08 10000-TiN $60.24 10002 $87.54 10003 $156.42

TOOL SETS

33

Countersink & Deburring Tools

Carbide Countersink Sets

HSS & Cobalt 3-Flute Center Reamer Sets

Straight Shank, CNC Precision Cam Ground, Cobalt, Chatter-free Cutting Action.

Carbide sets include one 1/4, 3/8, 1/2, 5/8, and 3/4” body diameter with a particular included point angle.

Each 5-piece set includes one piece each of 1/4, 3/8, 1/2, 3/4, and 1” body diameter with a particular included point angle.

CountersinkAngle 4-Piece Price 5-Piece Price 5-Piece

Coated Price

60° 53508 $72.84 53509 $124.06 53509-TiN $156.80

82° 53518 $72.84 53519 $124.06 53519-TiN $156.80

90° 53528 $72.84 53529 $124.06 53529-TiN $156.80

100° 53538 $72.84 53539 $124.06 53539-TiN $156.80

HeadDiameter

5/16

3/8

1/2

5/8

5/163/81/23/41

5/163/81/23/41

Pkg Qty.

CountersinkAngle HSS Price CO Price

1 60° 50026 $114.19 50036 $131.31

1 82° 50028 $114.19 50038 $131.31

1 90° 50029 $114.19 50039 $131.31

1 100° 50020 $114.19 50030 $131.31

1 110° 50021 $114.19 50031 $131.31

1 120° 50022 $114.19 50032 $131.31

PkgQty.

CountersinkAngle

SingleFlute Price 3-Flute Price 6-Flute Price

1 60° 55709 $350.46 55749 $357.46 55790 $368.18

1 60° 55709-TiALN $424.91 55749-TiALN $433.41 55790-TiALN $446.42

1 82° 55719 $350.46 55759 $357.46 55801 $368.18


1 90° 55729 $350.46 55769 $357.46 55812 $368.18


1 100° 55739 $350.46 55779 $357.46 55823 $368.18




Many tools are available with additional coatings. All dimensions are in inches.Please call for quote.

Repairs & Reconditioning

AFTER

• Full Line of stocked hardware

• Capable of repairing ANY manufacturer and insert type

• All tools are brought back to original manufacturers specifications

• 4 week standard, Same day rush service available

• Experienced with HSK, KM, CAPTO, and all standard machine tapers

EMAIL as attachment: [email protected] (or) Text: 969-233-6482

Save Time & MoneyInvolved with Shipping!Simply take a pic of your damaged tool...

- Include Your Name and Contact Information- Reference Your Distributor & Part Numbers

SAVE up to 75% OFF

The cost of New tooling!

Affiliated Distributors Guide - ARCH Cutting Tools · 2019. 11. 14. · USCTI, ISA ULTRA-DEX Ph:...

Documents

Transcript of Affiliated Distributors Guide - ARCH Cutting Tools · 2019. 11. 14. · USCTI, ISA ULTRA-DEX Ph:...