ADVISORS EXCEL -GAGE CENTER CAMPUS PHASE 1 -DEMO …€¦ · vwc vinyl wall covering vwf vinyl wall...
16
GRAPHIC SYMBOLS MATERIAL LEGEND ACOUSTIC TILE (SECTION) BATT INSULATION BRICK CARPET CONCRETE CONCRETE MASONRY UNITS CONCRETE, PLASTER CUT STONE, STUCCO METAL STUDS PLYWOOD (LARGE SIZE) RIGID INSULATION SAND, GRAVEL, PLASTER, DRYWALL, CUT STONE, GROUT TILE (LARGE SCALE) WOOD BLOCKING WOOD MEMBER (CONTINUOUS) WOOD STUDS, PARALAM, FINISHED BRICK PLAN OR SECTION METAL GLASS WOOD ELEVATION EARTH COMPACTED/ DISTURBED CONTACT INFORMATION SUMMARY OWNER CONTACT INFORMATION : AMY KLOTZ 2950 SW MC CLURE RD TOPEKA, KS 66614 PHONE: 555-555-5555 EMAIL: [email protected] DESIGN TEAM ARCHITECTURAL DESIGN SCHWERDT DESIGN GROUP 2231 SW WANAMAKER RD SUITE 303 TOPEKA, KANSAS 66614 CONTACT: PHONE: FAX: E-MAIL: LAUREN FITZPATRICK 785-273-7540 785-273-7579 [email protected] CIVIL DESIGN CFS ENGINEERS 2930 SW WOODSIDE DR TOPEKA, KS 66614 CONTACT: PHONE: FAX: E-MAIL: KEVIN HOLLAND, P.E. 785-272-4706 785-272-4736 [email protected] STRUCTURAL DESIGN CERTUS STRUCUTRAL ENGINEERS, INC 900 S KANSAS AVE, SUITE 400 TOPEKA, KS 66614 CONTACT: PHONE: FAX: E-MAIL: TOBY TAGGART, P.E. 785-291-0400 785-291-0401 [email protected] MECHANICAL & ELECTRICAL DESIGN L S & A 3639 SW SUMMERFIELD DR STE. A TOPEKA, KS 66614 CONTACT: PHONE: FAX: E-MAIL: JAMES A. LATIMER, P.E., LEED AP, CGD 785-233-3232 785-233-0647 [email protected] N A1 LOCATION MAP SCALE: NOT TO SCALE PROJECT LOCATION CODE PLAN LEGEND 1-HR CORRIDOR 2-HR SEPARATION 1-HR SEPARATION ABBREVIATIONS A AFF ABOVE FINISH FLOOR ACS PNL ACCESS PANEL ACC ACCESSIBLE ACT ACOUSTICAL CEILING TILE ACOUS PNL ACOUSTICAL PANEL ADMIN ADMINISTRATION APC ACOUSTICAL PANEL CEILING AWT ACOUSTICAL WALL TREATMENT ADJ ADJUSTABLE AHU AIR HANDLING UNIT ALT ALTERNATE ALUM ALUMINUM AB ANCHOR BOLT L ANGLE ANOD ANODIZE / ANODIZED APPROX APPROXIMATE ARCH ARCHITECTURAL ASPH ASPHALT B BSMT BASEMENT BM BEAM BRG BEARING BRG PL BEARING PLATE BR BEDROOM BLW BELOW BTWN BETWEEN BITUM BITUMINOUS BD BOARD BF BOTH FACES BS BOTH SIDES BW BOTH WAYS BOT BOTTOM BRKT BRACKET BLDG BUILDING BUR BUILT-UP ROOFING C CAB CABINET CUH CABINET UNIT HEATER CPT CARPET CIP CAST-IN-PLACE CS CAST STONE CLG CEILING CEM CEMENT CTR CENTER CL CENTER LINE C TO C CERAMIC TILE CH BD CHALKBOARD C CHANNEL CLR CLEAR CLO CLOSET COL COLUMN CONC CONCRETE CMU CONCRETE MASONRY UNIT CJ CONSTRUCTION JOINT, CONTROL JOINT D DL DEAD LOAD DEMO DEMOLITION DEPT DEPARTMENT D DEPTH DET DETAIL DIAG DIAGONAL DIA DIAMETER DIM DIMENSION D CONTINUED DW DISHWASHER DR DOOR DBL DOUBLE DN DOWN DS DOWNSPOUT DWG DRAWING DF DRINKING FOUNTAIN E EA EACH EW EACH WAY ESMT EASEMENT E EAST ELEC ELECTRIC, ELECTRICAL EL ELEVATION ELEV ELEVATOR EQ EQUAL EQUIP EQUIPMENT EXH FN EXHAUST FAN EXIST EXISTING EXP EXPANSION EJ EXPANSION JOINT EXT EXTERIOR EIFS EXTERIOR INSULATION & FINISH SYSTEM F FC BRK FACE BRICK FOF FACE OF FINISH FGL FIBERGLASS FIN FINISH FF EL FINISH FLOOR ELEVATION FE FIRE EXTINGUISHER FEC FIRE EXTINGUISHER CABINET FIXT FIXTURE FLASH FLASHING FLR FLOOR FCO FLOOR CLEANOUT FD FLOOR DRAIN FLUOR FLUORESCENT FLL FLOW LINE FT FOOT FTG FOOTING FDTN FOUNDATION FR FRAME FA FRESH AIR FURN FURNACE FURG FURRING FS FULL SIZE G GA GAUGE GALV STL GALVANIZED STEEL GC GENERAL CONTRACTOR GL GLASS GB GRAB BAR GYP BD GYPSUM BOARD H HCP HANDICAPPED HDW HARDWARE HDWD HARDWOOD HVAC HEATING, VENTILATION & AIR CONDITIONING HT HEIGHT H HIGH HWY HIGHWAY HM HOLLOW METAL HORIZ HORIZONTAL HP HORESEPOWER H CONTINUED HW HOT WATER HYD HYDRANT I INCL INCLUDED ID INSIDE DIAMETER INSUL INSULATION INT INTERIOR J JAN JANITOR K KIT KITCHEN L L ANGLE LAB LABORATORY LAM LAMINATE LAU LAUNDRY LAV LAVATORY LWC LIGHTWEIGHT CONCRETE LCMU LIGHTWEIGHT CONCRETE MASONRY LF LINEAR FOOT LL LIVE LOAD LR LIVING ROOM LLH LONG LEG HORIZONTAL LLV LONG LEG VERTICAL M MAINT MAINTENANCE MH MANHOLE MFD MANUFACTURED MFR MANUFACTURER MFG MANUFACTURING MO MASONRY OPENING MBR MASTER BEDROOM MATL MATERIAL MAX MAXIMUM MECH MECHANICAL MTL METAL MW MICROWAVE MIN MINIMUM, MINUTE MISC MISCELLANEOUS MR MOISTURE RESISTANT MTD MOUNTED MULL MULLION N NRC NOISE REDUCTION COEFFICIENT NOM NOMINAL N NORTH NIC NOT IN CONTRACT NTS NOT TO SCALE O OFF OFFICE OC ON CENTER OPNG OPENING OPP OPPOSITE OD OUTSIDE DIAMETER O/O OUT TO OUT OA OVERALL ORD OVERFLOW ROOF DRAIN OH OVERHANG OF/CI OWNER FURNISHED/ CONTRACTOR INSTALLED OF/OI OWNER FURNISHED/ OWNER INSTALLED P PT PAINT PR PAIR PNL PANEL PTD PAPER TOWEL DISPENSER PBD PARTICLE BOARD PTN PARTITION PVG PAVING PERF PERFORATED PERIM PERIMETER PLAS PLASTER PERP PERPENDICULAR PLAM PLASTIC LAMINATE PLYWD PLYWOOD PVC POLYVINYL CHLORIDE LB POUND PCF POUNDS PER CUBIC FOOT PLF POUNDS PER LINEAR FOOT PSF POUNDS PER SQUARE FOOT PSI POUNDS PER SQUARE INCH PCC PRECAST CONCRETE PREFAB PREFABRICATE PREFIN PREFINISH PROJ PROJECT PL PROPERTY LINE Q QT QUARRY TILE R REF REFERENCE, REFRIGERATOR RCP REFLECTED CEILING PLAN REINF REINFORCE REQD REQUIRED RESIL RESILIENT REST RESTROOM RA RETURN AIR REV REVISION R RISER, RADIUS, RANGE RD ROOF DRAIN RFG ROOFING RM ROOM RO ROUGH OPENING RS ROUGH SAWN S SNU SANITARY NAPKIN DISPENSER SNDU SANITARY NAPKIN DISPOSAL UNIT SS SANITARY SEWER SCHED SCHEDULE SECT SECTION SHT SHEET SV SHEET VINYL SHV SHELVING SHR SHOWER SIM SIMILAR SCWD SOLID CORE WOOD STC SOUND TRANSMISSION CLASS S SOUTH SPEC SPECIFICATION SB SPLASH BLOCK SF SQUARE FOOT SQ IN SQUARE INCH SQ YD SQUARE YARD SST STAINLESS STEEL STD STANDARD STL JST STEEL JOIST STOR STORAGE SD STORM DRAIN ST STREET S CONTINUED T TK BD TACKBOARD TEL TELEPHONE TV TELEVISION TMPD TEMPERED TER TERRAZZO THK THICKNESS TPD TOILET PAPER HOLDER T&G TONGUE AND GROOVE T&B TOP AND BOTTOM TOC TOP OF CURB, TOP OF CONCRETE TOF TOP OF FOOTING TOM TOP OF MASONRY TOS TOP OF STEEL TOW TOP OF WALL TB TOWEL BAR TRANS TRANSPARENT *TF TRANSPARENT WOOD FINISH T TREAD TYP TYPICAL U UNFIN UNFINISHED UH UNIT HEATER UNO UNLESS NOTED OTHERWISE V VR VAPOR RETARDER VNR VENEER VENT VENTILATION VERT VERTICAL VEST VESTIBULE VB VINYL BASE VCT VINYL COMPOSITION TILE VWC VINYL WALL COVERING VWF VINYL WALL FABRIC V VOLT W WSCT WAINSCOT WC WALL COVERING, WATER CLOSET WH WATER HEATER WP WATERPROOFING, WORKING POINT WT WEIGHT WWF WELDED WIRE FABRIC W WEST, WIDE WDW WINDOW WGL WIRED GLASS W/ WITH W/O WITHOUT WD WOOD D101B WALL SECTION TAG P2 1t PARTITION TYPE TAG ROOM TAG DOOR TAG ELEVATION TAG WINDOW TAG A-303 A2 SIM DETAIL CALLOUT A - 202 B3 B3 B3 B3 / SMALL REFERENCE NOTE A1 A-101 1 / 1 A-101 REVISION MARK BEARING ELEVATION MARK CENTERLINE MARK / 1 A-101 MATCHLINE DESCRIPTIVE ARROW EQUIPMENT TAG 1 1i DEMOLITION MARK GENERAL NOTE MARK 1 NEW CONSTRUCTION MARK SPOT ELEVATION 1 EXISTING NEW EL - FLOOR 100'-0" SHEET INDEX ROOM NAME 101 B5 A-202 SIM STRUCT STRUCTURAL SUSP CLG SUSPENDED CEILING SW SWITCH BUILDING ADDRESS : 4125 SW Gage Center Dr Suite 201, Topeka, KS 66604 ARCHITECT CONTACT INFORMATION : LAUREN FITZPATRICK : SCHWERDT DESIGN GROUP 2231 SW WANAMAKER RD. SUITE 303 TOPEKA, KS 66614 PHONE: 785.273.7579 EMAIL: [email protected] SHEET TITLE PROJECT NUMBER SHEET NUMBER A B C D 5 4 3 2 1 A B C D FILE PATH: DATE: DRAWN BY: 5 4 3 2 1 SUBMISSION DATES 500 north broadway suite 200 oklahoma city, ok 73102 phone: 405.231.3105 schwerdt design group architecture interiors planning 2231 sw wanamaker rd suite 303 topeka, kansas 66614-4275 phone: 785.273.7540 C:\Users\Lauren\Documents\190121 AE Corporate Office (GageCenter)_lnfLKK7H.rvt 8/6/2019 2:44:30 PM ADVISORS EXCEL - GAGE CENTER CAMPUS PHASE 1 - DEMO PACKAGE TOPEKA, KANSAS 66604 COVER SHEET 190121 G-001 Author ADVISORS EXCEL - GAGE CENTER CAMPUS PHASE 1 - DEMO PACKAGE TOPEKA, KANSAS 66604 GENERAL G-001 COVER SHEET DEMO D-100 DEMO PLAN - BUILDING A - LOWER LEVEL D-101 DEMO PLAN - BUILDING A - FIRST FLOOR D-102 DEMO PLAN - BUILDING A - SECOND FLOOR D-103 DEMO PLAN - BUILDING K - FIRST FLOOR D-104 DEMO PLAN - BUILDING K - SECOND FLOOR D-201 EXTERIOR DEMO ELEVATIONS - BUILDING A D-202 EXTERIOR DEMO ELEVATIONS - BUILDING A D-203 EXTERIOR DEMO ELEVATIONS - BUILDING K D-204 EXTERIOR DEMO ELEVATIONS - BUILDING K ME- 01 BUILDING A - LOWER LEVEL DEMOLITION PLAN - MECHANICAL/ELECTRICAL ME- 02 BUILDING A - FIRST FLOOR DEMOLITION PLAN - MECHANICAL/ELECTRICAL ME- 03 BUILDING A - SECOND FLOOR DEMOLITION PLAN - MECHANICAL/ELECTRICAL ME- 04 BUILDING A - ROOFTOP DEMOLITION PLAN - MECHANICAL/ELECTRICAL ME- 05 BUILDING K - FIRST FLOOR DEMOLITION PLAN - MECHANICAL/ELECTRICAL ME- 06 BUILDING K - SECOND FLOOR DEMOLITION PLAN - MECHANICAL/ELECTRICAL SECTION 024119 - SELECTIVE DEMOLITION PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section. 1.2 SUMMARY A. Section Includes: 1. Demolition and removal of selected portions of building or structure. 2. Demolition and removal of selected site elements. 3. Salvage of existing items to be reused or recycled. 1.3 DEFINITIONS A. Remove: Detach items from existing construction and legally dispose of them off-site unless indicated to be removed and salvaged or removed and reinstalled. B. Remove and Salvage: Carefully detach from existing construction, in a manner to prevent damage, and leave at site ready for reuse. C. Remove and Reinstall: Detach items from existing construction, prepare for reuse, and reinstall where indicated. D. Existing to Remain: Existing items of construction that are not to be permanently removed and that are not otherwise indicated to be removed, removed and salvaged, or removed and reinstalled. 1.4 MATERIALS OWNERSHIP A. Unless otherwise indicated, demolition waste becomes property of Contractor. B. Historic items, relics, antiques, and similar objects including, but not limited to, cornerstones and their contents, commemorative plaques and tablets, and other items of interest or value to Owner that may be uncovered during demolition remain the property of Owner. 1. Carefully salvage in a manner to prevent damage and promptly return to Owner. 1.5 PREINSTALLATION MEETINGS A. Predemolition Conference: Conduct conference at Project site. 1. Inspect and discuss condition of construction to be selectively demolished. 2. Review structural load limitations of existing structure. 3. Review and finalize selective demolition schedule and verify availability of materials, demolition personnel, equipment, and facilities needed to make progress and avoid delays. 4. Review requirements of work performed by other trades that rely on substrates exposed by selective demolition operations. 5. Review areas where existing construction is to remain and requires protection. 1.6 INFORMATIONAL SUBMITTALS A. Schedule of Selective Demolition Activities: Indicate the following: 1. Detailed sequence of selective demolition and removal work, with starting and ending dates for each activity. 2. Interruption of utility services. Indicate how long utility services will be interrupted. 3. Coordination for shutoff, capping, and continuation of utility services. 4. Use of stairs. 1.7 FIELD CONDITIONS A. Notify Architect of discrepancies between existing conditions and Drawings before proceeding with selective demolition. B. Hazardous Materials: Present in buildings and structures to be selectively demolished. A report on the presence of hazardous materials is on file for review and use. Examine report to become aware of locations where hazardous materials are present. 1. Do not disturb hazardous materials or items suspected of containing hazardous materials except under procedures specified elsewhere in the Contract Documents. C. Utility Service: Maintain existing utilities indicated to remain in service and protect them against damage during selective demolition operations. PART 2 - PRODUCTS (NOT USED) PART 3 - EXECUTION 3.1 EXAMINATION A. Verify that utilities have been disconnected and capped before starting selective demolition operations. B. Survey existing conditions and correlate with requirements indicated to determine extent of selective demolition required. C. When unanticipated mechanical, electrical, or structural elements that conflict with intended function or design are encountered, investigate and measure the nature and extent of conflict. Promptly submit a written report to Architect. D. Survey of Existing Conditions: Record existing conditions by use of measured drawings and preconstruction photographs. 3.2 UTILITY SERVICES AND MECHANICAL/ELECTRICAL SYSTEMS A. Existing Services/Systems to Remain: Maintain services/systems indicated to remain and protect them against damage. 1. Comply with requirements for existing services/systems interruptions specified in Section 011000 "Summary." B. Existing Services/Systems to Be Removed, Relocated, or Abandoned: Locate, identify, disconnect, and seal or cap off indicated utility services and mechanical/electrical systems serving areas to be selectively demolished. 1. Arrange to shut off indicated utilities with utility companies. 2. Disconnect, demolish, and remove fire-suppression systems, plumbing, and HVAC systems, equipment, and components indicated to be removed. a. Piping to Be Removed: Remove portion of piping indicated to be removed and cap or plug remaining piping with same or compatible piping material. b. Piping to Be Abandoned in Place: Drain piping and cap or plug piping with same or compatible piping material. c. Equipment to Be Removed: Disconnect and cap services and remove equipment. d. Ducts to Be Removed: Remove portion of ducts indicated to be removed and plug remaining ducts with same or compatible ductwork material. e. Ducts to Be Abandoned in Place: Cap or plug ducts with same or compatible ductwork material. C. Refrigerant: Remove refrigerant from mechanical equipment to be selectively demolished according to 40 CFR 82 and regulations of authorities having jurisdiction. 3.3 PREPARATION A. Site Access and Temporary Controls: Conduct selective demolition and debris-removal operations to ensure minimum interference with roads, streets, walks, walkways, and other adjacent occupied and used facilities. 1. Comply with requirements for access and protection specified in Section 015000 "Temporary Facilities and Controls." B. Temporary Facilities: Provide temporary barricades and other protection required to prevent injury to people and damage to adjacent buildings and facilities to remain. 1. Provide protection to ensure safe passage of people around selective demolition area. 2. Provide temporary weather protection, during interval between selective demolition of existing construction on exterior surfaces and new construction, to prevent water leakage and damage to structure and interior areas. 3. Protect walls, ceilings, floors, and other existing finish work that are to remain or that are exposed during selective demolition operations. 4. Comply with requirements for temporary enclosures, dust control, heating, and cooling specified in Section 015000 "Temporary Facilities and Controls." C. Temporary Shoring: Provide and maintain shoring, bracing, and structural supports as required to preserve stability and prevent movement, settlement, or collapse of construction and finishes to remain, and to prevent unexpected or uncontrolled movement or collapse of construction being demolished. 1. Strengthen or add new supports when required during progress of selective demolition. 3.4 SELECTIVE DEMOLITION, GENERAL A. General: Demolish and remove existing construction only to the extent required by new construction and as indicated. Use methods required to complete the Work within limitations of governing regulations and as follows: 1. Neatly cut openings and holes plumb, square, and true to dimensions required. Use cutting methods least likely to damage construction to remain or adjoining construction. Use hand tools or small power tools designed for sawing or grinding, not hammering and chopping, to minimize disturbance of adjacent surfaces. Temporarily cover openings to remain. 2. Cut or drill from the exposed or finished side into concealed surfaces to avoid marring existing finished surfaces. 3. Do not use cutting torches until work area is cleared of flammable materials. At concealed spaces, such as duct and pipe interiors, verify condition and contents of hidden space before starting flame-cutting operations. Maintain portable fire-suppression devices during flame-cutting operations. 4. Maintain adequate ventilation when using cutting torches. 5. Remove decayed, vermin-infested, or otherwise dangerous or unsuitable materials and promptly dispose of off-site. 6. Remove structural framing members and lower to ground by method suitable to avoid free fall and to prevent ground impact or dust generation. 7. Locate selective demolition equipment and remove debris and materials so as not to impose excessive loads on supporting walls, floors, or framing. 8. Dispose of demolished items and materials promptly. B. Removed and Reinstalled Items: 1. Clean and repair items to functional condition adequate for intended reuse. 2. Protect items from damage during storage. 3. Reinstall items in locations indicated. Comply with installation requirements for new materials and equipment. Provide connections, supports, and miscellaneous materials necessary to make item functional for use indicated. C. Existing Items to Remain: Protect construction indicated to remain against damage and soiling during selective demolition. When permitted by Architect, items may be removed to a suitable, protected storage location during selective demolition and cleaned and reinstalled in their original locations after selective demolition operations are complete. 3.5 SELECTIVE DEMOLITION PROCEDURES FOR SPECIFIC MATERIALS A. Concrete: Demolish in small sections. Using power-driven saw, cut concrete to a depth of at least 3/4 inch at junctures with construction to remain. Dislodge concrete from reinforcement at perimeter of areas being demolished, cut reinforcement, and then remove remainder of concrete. Neatly trim openings to dimensions indicated. B. Masonry: Demolish in small sections. Cut masonry at junctures with construction to remain, using power-driven saw, then remove masonry between saw cuts. C. Concrete Slabs-on-Grade: Saw-cut perimeter of area to be demolished, then break up and remove. D. Roofing: Remove no more existing roofing than what can be covered in one day by new roofing and so that building interior remains watertight and weathertight. See Section <Insert Section number and title> for new roofing requirements. 1. Remove existing roof membrane, flashings, copings, and roof accessories. 2. Remove existing roofing system down to substrate. 3.6 DISPOSAL OF DEMOLISHED MATERIALS A. General: Except for items or materials indicated to be reused, salvaged, reinstalled, or otherwise indicated to remain Owner's property, remove demolished materials from Project site. 1. Do not allow demolished materials to accumulate on-site. 2. Remove and transport debris in a manner that will prevent spillage on adjacent surfaces and areas. 3. Remove debris from elevated portions of building by chute, hoist, or other device that will convey debris to grade level in a controlled descent. B. Burning: Do not burn demolished materials. C. Disposal: Transport demolished materials off Owner's property and legally dispose of them. 3.7 CLEANING A. Clean adjacent structures and improvements of dust, dirt, and debris caused by selective demolition operations. Return adjacent areas to condition existing before selective demolition operations began. END OF SECTION 024119 2019-08-06 16:43-05:00
Transcript of ADVISORS EXCEL -GAGE CENTER CAMPUS PHASE 1 -DEMO …€¦ · vwc vinyl wall covering vwf vinyl wall...
GRAPHIC SYMBOLS
MATERIAL LEGEND
ACOUSTIC TILE (SECTION)
BATT INSULATION
BRICK
CARPET
CONCRETE
CONCRETE MASONRY UNITS
CONCRETE, PLASTER CUT STONE, STUCCO
METAL STUDS
PLYWOOD (LARGE SIZE)
RIGID INSULATION
SAND, GRAVEL, PLASTER, DRYWALL, CUT STONE, GROUTTILE (LARGE SCALE)
WOOD BLOCKING
WOOD MEMBER (CONTINUOUS)
WOOD STUDS, PARALAM, FINISHED
BRICK
PLAN OR SECTION
METALGLASS
WOOD
ELEVATIONEARTH COMPACTED/ DISTURBED
CONTACT INFORMATION SUMMARY
OWNER CONTACT INFORMATION : AMY KLOTZ2950 SW MC CLURE RD TOPEKA, KS 66614PHONE: 555-555-5555EMAIL: [email protected]
DESIGN TEAM
ARCHITECTURAL DESIGN
SCHWERDT DESIGN GROUP2231 SW WANAMAKER RD SUITE 303TOPEKA, KANSAS 66614
CONTACT:PHONE:FAX:E-MAIL:
LAUREN [email protected]
CIVIL DESIGN
CFS ENGINEERS2930 SW WOODSIDE DRTOPEKA, KS 66614
CONTACT:PHONE:FAX:E-MAIL:
KEVIN HOLLAND, [email protected]
STRUCTURAL DESIGN
CERTUS STRUCUTRAL ENGINEERS, INC900 S KANSAS AVE, SUITE 400TOPEKA, KS 66614
CONTACT:PHONE:FAX:E-MAIL:
TOBY TAGGART, [email protected]
MECHANICAL & ELECTRICAL DESIGN
L S & A3639 SW SUMMERFIELD DR STE. ATOPEKA, KS 66614
CONTACT:PHONE:FAX:E-MAIL:
JAMES A. LATIMER, P.E., LEED AP, [email protected]
N
A1LOCATION MAPSCALE: NOT TO SCALE
PROJECT LOCATION
CODE PLAN LEGEND
1-HR CORRIDOR
2-HR SEPARATION
1-HR SEPARATION
ABBREVIATIONS
AAFF ABOVE FINISH FLOORACS PNL ACCESS PANELACC ACCESSIBLEACT ACOUSTICAL CEILING TILEACOUS PNL ACOUSTICAL PANELADMIN ADMINISTRATIONAPC ACOUSTICAL PANEL
CEILINGAWT ACOUSTICAL WALL
TREATMENTADJ ADJUSTABLEAHU AIR HANDLING UNITALT ALTERNATEALUM ALUMINUMAB ANCHOR BOLTL ANGLEANOD ANODIZE / ANODIZEDAPPROX APPROXIMATEARCH ARCHITECTURALASPH ASPHALT
BBSMT BASEMENTBM BEAMBRG BEARINGBRG PL BEARING PLATEBR BEDROOMBLW BELOWBTWN BETWEENBITUM BITUMINOUSBD BOARDBF BOTH FACESBS BOTH SIDESBW BOTH WAYSBOT BOTTOMBRKT BRACKETBLDG BUILDINGBUR BUILT-UP ROOFING
CCAB CABINETCUH CABINET UNIT HEATERCPT CARPETCIP CAST-IN-PLACECS CAST STONECLG CEILINGCEM CEMENTCTR CENTERCL CENTER LINEC TO C CERAMIC TILECH BD CHALKBOARDC CHANNELCLR CLEARCLO CLOSETCOL COLUMNCONC CONCRETECMU CONCRETE MASONRY UNITCJ CONSTRUCTION JOINT,
CONTROL JOINT
DDL DEAD LOADDEMO DEMOLITIONDEPT DEPARTMENTD DEPTHDET DETAILDIAG DIAGONALDIA DIAMETERDIM DIMENSION
D CONTINUEDDW DISHWASHERDR DOORDBL DOUBLEDN DOWNDS DOWNSPOUTDWG DRAWINGDF DRINKING FOUNTAIN
EEA EACHEW EACH WAYESMT EASEMENTE EASTELEC ELECTRIC, ELECTRICALEL ELEVATIONELEV ELEVATOREQ EQUALEQUIP EQUIPMENTEXH FN EXHAUST FANEXIST EXISTINGEXP EXPANSIONEJ EXPANSION JOINTEXT EXTERIOREIFS EXTERIOR INSULATION
& FINISH SYSTEM
FFC BRK FACE BRICKFOF FACE OF FINISHFGL FIBERGLASSFIN FINISHFF EL FINISH FLOOR ELEVATIONFE FIRE EXTINGUISHERFEC FIRE EXTINGUISHER CABINETFIXT FIXTUREFLASH FLASHINGFLR FLOORFCO FLOOR CLEANOUTFD FLOOR DRAINFLUOR FLUORESCENTFLL FLOW LINEFT FOOTFTG FOOTINGFDTN FOUNDATIONFR FRAMEFA FRESH AIRFURN FURNACEFURG FURRINGFS FULL SIZE
GGA GAUGEGALV STL GALVANIZED STEELGC GENERAL CONTRACTORGL GLASSGB GRAB BARGYP BD GYPSUM BOARD
HHCP HANDICAPPEDHDW HARDWAREHDWD HARDWOODHVAC HEATING, VENTILATION
& AIR CONDITIONINGHT HEIGHTH HIGHHWY HIGHWAYHM HOLLOW METALHORIZ HORIZONTALHP HORESEPOWER
H CONTINUEDHW HOT WATERHYD HYDRANT
IINCL INCLUDEDID INSIDE DIAMETERINSUL INSULATIONINT INTERIOR
JJAN JANITOR
KKIT KITCHEN
LL ANGLELAB LABORATORYLAM LAMINATELAU LAUNDRYLAV LAVATORYLWC LIGHTWEIGHT CONCRETELCMU LIGHTWEIGHT CONCRETE
MASONRYLF LINEAR FOOTLL LIVE LOADLR LIVING ROOMLLH LONG LEG HORIZONTALLLV LONG LEG VERTICAL
MMAINT MAINTENANCEMH MANHOLEMFD MANUFACTUREDMFR MANUFACTURERMFG MANUFACTURINGMO MASONRY OPENINGMBR MASTER BEDROOMMATL MATERIALMAX MAXIMUMMECH MECHANICALMTL METALMW MICROWAVEMIN MINIMUM, MINUTEMISC MISCELLANEOUSMR MOISTURE RESISTANTMTD MOUNTEDMULL MULLION
NNRC NOISE REDUCTION
COEFFICIENTNOM NOMINALN NORTHNIC NOT IN CONTRACTNTS NOT TO SCALE
OOFF OFFICEOC ON CENTEROPNG OPENINGOPP OPPOSITEOD OUTSIDE DIAMETERO/O OUT TO OUTOA OVERALLORD OVERFLOW ROOF DRAINOH OVERHANGOF/CI OWNER FURNISHED/
CONTRACTOR INSTALLEDOF/OI OWNER FURNISHED/
OWNER INSTALLED
PPT PAINTPR PAIRPNL PANELPTD PAPER TOWEL DISPENSERPBD PARTICLE BOARDPTN PARTITIONPVG PAVINGPERF PERFORATEDPERIM PERIMETERPLAS PLASTERPERP PERPENDICULARPLAM PLASTIC LAMINATEPLYWD PLYWOODPVC POLYVINYL CHLORIDELB POUNDPCF POUNDS PER CUBIC FOOTPLF POUNDS PER LINEAR FOOTPSF POUNDS PER SQUARE FOOTPSI POUNDS PER SQUARE INCHPCC PRECAST CONCRETEPREFAB PREFABRICATEPREFIN PREFINISHPROJ PROJECTPL PROPERTY LINE
QQT QUARRY TILE
RREF REFERENCE,
REFRIGERATORRCP REFLECTED CEILING PLANREINF REINFORCEREQD REQUIREDRESIL RESILIENTREST RESTROOMRA RETURN AIRREV REVISIONR RISER, RADIUS, RANGERD ROOF DRAINRFG ROOFINGRM ROOMRO ROUGH OPENINGRS ROUGH SAWN
SSNU SANITARY NAPKIN DISPENSERSNDU SANITARY NAPKIN DISPOSAL UNITSS SANITARY SEWERSCHED SCHEDULESECT SECTIONSHT SHEETSV SHEET VINYLSHV SHELVINGSHR SHOWERSIM SIMILARSCWD SOLID CORE WOODSTC SOUND TRANSMISSION CLASSS SOUTHSPEC SPECIFICATIONSB SPLASH BLOCKSF SQUARE FOOTSQ IN SQUARE INCHSQ YD SQUARE YARDSST STAINLESS STEELSTD STANDARDSTL JST STEEL JOISTSTOR STORAGESD STORM DRAINST STREET
S CONTINUED
TTK BD TACKBOARDTEL TELEPHONETV TELEVISIONTMPD TEMPEREDTER TERRAZZOTHK THICKNESSTPD TOILET PAPER HOLDERT&G TONGUE AND GROOVET&B TOP AND BOTTOMTOC TOP OF CURB,
TOP OF CONCRETETOF TOP OF FOOTINGTOM TOP OF MASONRYTOS TOP OF STEELTOW TOP OF WALLTB TOWEL BARTRANS TRANSPARENT*TF TRANSPARENT WOOD
FINISHT TREADTYP TYPICAL
UUNFIN UNFINISHEDUH UNIT HEATERUNO UNLESS NOTED OTHERWISE
VVR VAPOR RETARDERVNR VENEERVENT VENTILATIONVERT VERTICALVEST VESTIBULEVB VINYL BASEVCT VINYL COMPOSITION TILEVWC VINYL WALL COVERINGVWF VINYL WALL FABRICV VOLT
WWSCT WAINSCOTWC WALL COVERING,
WATER CLOSETWH WATER HEATERWP WATERPROOFING,
WORKING POINTWT WEIGHTWWF WELDED WIRE FABRICW WEST, WIDEWDW WINDOWWGL WIRED GLASSW/ WITHW/O WITHOUTWD WOOD
D101B
WALL SECTION TAG
P2
1t
PARTITION TYPE TAG
ROOM TAG
DOOR TAG
ELEVATION TAG
WINDOW TAG
A-303
A2SIM
DETAIL CALLOUT
A-202
B3
B3B3
B3
/SMALL REFERENCE NOTE
A1A-101
1
/ 1A-101
REVISION MARK
BEARING ELEVATION MARK
CENTERLINE MARK
/ 1A-101MATCHLINE
DESCRIPTIVE ARROW
EQUIPMENT TAG
1
1i
DEMOLITION MARK
GENERAL NOTE MARK 1
NEW CONSTRUCTION MARK
SPOT ELEVATION
1
EXISTINGNEW
EL - FLOOR
100'-0"
SHEET INDEX ROOM NAME
101
B5
A-202
SIM
STRUCT STRUCTURALSUSP CLG SUSPENDED CEILINGSW SWITCH
BUILDING ADDRESS : 4125 SW Gage Center Dr Suite 201, Topeka, KS 66604
ARCHITECT CONTACT INFORMATION :
LAUREN FITZPATRICK : SCHWERDT DESIGN GROUP2231 SW WANAMAKER RD. SUITE 303TOPEKA, KS 66614PHONE: 785.273.7579EMAIL: [email protected]
SHEET TITLE
PROJECT NUMBER
SHEET NUMBER
A
B
C
D
54321
A
B
C
D
FILE
PA
TH:
DA
TE:
DR
AW
N B
Y:
54321
SUBMISSION DATES
500 north broadway suite 200oklahoma city, ok 73102phone: 405.231.3105
schwerdt design grouparchitecture interiors planning2231 sw wanamaker rd suite 303topeka, kansas 66614-4275phone: 785.273.7540
C:\U
sers
\Laure
n\D
ocum
ents
\190121 A
E C
orp
ora
te O
ffic
e (
GageC
ente
r)_ln
fLK
K7H
.rvt
8/6
/2019 2
:44:3
0 P
M
AD
VIS
OR
S E
XC
EL
-G
AG
E C
EN
TE
R C
AM
PU
S
PH
AS
E 1
-D
EM
O P
AC
KA
GE
TO
PE
KA
, KA
NS
AS
666
04
COVER SHEET
190121
G-001
Aut
hor
ADVISORS EXCEL - GAGE CENTER CAMPUS
PHASE 1 - DEMO PACKAGETOPEKA, KANSAS 66604
GENERAL
G-001 COVER SHEET
DEMO
D-100 DEMO PLAN - BUILDING A - LOWER LEVEL
D-101 DEMO PLAN - BUILDING A - FIRST FLOOR
D-102 DEMO PLAN - BUILDING A - SECOND FLOOR
D-103 DEMO PLAN - BUILDING K - FIRST FLOOR
D-104 DEMO PLAN - BUILDING K - SECOND FLOOR
D-201 EXTERIOR DEMO ELEVATIONS - BUILDING A
D-202 EXTERIOR DEMO ELEVATIONS - BUILDING A
D-203 EXTERIOR DEMO ELEVATIONS - BUILDING K
D-204 EXTERIOR DEMO ELEVATIONS - BUILDING K
ME- 01 BUILDING A - LOWER LEVEL DEMOLITION PLAN -MECHANICAL/ELECTRICAL
ME- 02 BUILDING A - FIRST FLOOR DEMOLITION PLAN -MECHANICAL/ELECTRICAL
ME- 03 BUILDING A - SECOND FLOOR DEMOLITION PLAN -MECHANICAL/ELECTRICAL
ME- 04 BUILDING A - ROOFTOP DEMOLITION PLAN -MECHANICAL/ELECTRICAL
ME- 05 BUILDING K - FIRST FLOOR DEMOLITION PLAN -MECHANICAL/ELECTRICAL
ME- 06 BUILDING K - SECOND FLOOR DEMOLITION PLAN -MECHANICAL/ELECTRICAL
SECTION 024119 - SELECTIVE DEMOLITION
PART 1 - GENERAL1.1 RELATED DOCUMENTS
A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section.1.2 SUMMARY
A. Section Includes:1. Demolition and removal of selected portions of building or structure.2. Demolition and removal of selected site elements.3. Salvage of existing items to be reused or recycled.
1.3 DEFINITIONSA. Remove: Detach items from existing construction and legally dispose of them off-site unless indicated to be removed and salvaged or removed and reinstalled.B. Remove and Salvage: Carefully detach from existing construction, in a manner to prevent damage, and leave at site ready for reuse.C. Remove and Reinstall: Detach items from existing construction, prepare for reuse, and reinstall where indicated.D. Existing to Remain: Existing items of construction that are not to be permanently removed and that are not otherwise indicated to be removed, removed and salvaged, or removed and reinstalled.
1.4 MATERIALS OWNERSHIPA. Unless otherwise indicated, demolition waste becomes property of Contractor.B. Historic items, relics, antiques, and similar objects including, but not limited to, cornerstones and their contents, commemorative plaques and tablets, and other items of interest or value to Owner that may be uncovered during demolition remain the property of Owner.
1. Carefully salvage in a manner to prevent damage and promptly return to Owner.1.5 PREINSTALLATION MEETINGS
A. Predemolition Conference: Conduct conference at Project site.1. Inspect and discuss condition of construction to be selectively demolished.2. Review structural load limitations of existing structure.3. Review and finalize selective demolition schedule and verify availability of materials, demolition personnel, equipment, and facilities needed to make progress and avoid delays.4. Review requirements of work performed by other trades that rely on substrates exposed by selective demolition operations.5. Review areas where existing construction is to remain and requires protection.
1.6 INFORMATIONAL SUBMITTALSA. Schedule of Selective Demolition Activities: Indicate the following:
1. Detailed sequence of selective demolition and removal work, with starting and ending dates for each activity. 2. Interruption of utility services. Indicate how long utility services will be interrupted.3. Coordination for shutoff, capping, and continuation of utility services.4. Use of stairs.
1.7 FIELD CONDITIONSA. Notify Architect of discrepancies between existing conditions and Drawings before proceeding with selective demolition.B. Hazardous Materials: Present in buildings and structures to be selectively demolished. A report on the presence of hazardous materials is on file for review and use. Examine report to become aware of locations where hazardous materials are present.
1. Do not disturb hazardous materials or items suspected of containing hazardous materials except under procedures specified elsewhere in the Contract Documents.C. Utility Service: Maintain existing utilities indicated to remain in service and protect them against damage during selective demolition operations.
PART 2 - PRODUCTS (NOT USED)PART 3 - EXECUTION3.1 EXAMINATION
A. Verify that utilities have been disconnected and capped before starting selective demolition operations.B. Survey existing conditions and correlate with requirements indicated to determine extent of selective demolition required.C. When unanticipated mechanical, electrical, or structural elements that conflict with intended function or design are encountered, investigate and measure the nature and extent of conflict. Promptly submit a written report to Architect.D. Survey of Existing Conditions: Record existing conditions by use of measured drawings and preconstruction photographs.
3.2 UTILITY SERVICES AND MECHANICAL/ELECTRICAL SYSTEMSA. Existing Services/Systems to Remain: Maintain services/systems indicated to remain and protect them against damage.
1. Comply with requirements for existing services/systems interruptions specified in Section 011000 "Summary."B. Existing Services/Systems to Be Removed, Relocated, or Abandoned: Locate, identify, disconnect, and seal or cap off indicated utility services and mechanical/electrical systems serving areas to be selectively demolished.
1. Arrange to shut off indicated utilities with utility companies.2. Disconnect, demolish, and remove fire-suppression systems, plumbing, and HVAC systems, equipment, and components indicated to be removed.
a. Piping to Be Removed: Remove portion of piping indicated to be removed and cap or plug remaining piping with same or compatible piping material.b. Piping to Be Abandoned in Place: Drain piping and cap or plug piping with same or compatible piping material.c. Equipment to Be Removed: Disconnect and cap services and remove equipment.d. Ducts to Be Removed: Remove portion of ducts indicated to be removed and plug remaining ducts with same or compatible ductwork material.e. Ducts to Be Abandoned in Place: Cap or plug ducts with same or compatible ductwork material.
C. Refrigerant: Remove refrigerant from mechanical equipment to be selectively demolished according to 40 CFR 82 and regulations of authorities having jurisdiction.3.3 PREPARATION
A. Site Access and Temporary Controls: Conduct selective demolition and debris-removal operations to ensure minimum interference with roads, streets, walks, walkways, and other adjacent occupied and used facilities.1. Comply with requirements for access and protection specified in Section 015000 "Temporary Facilities and Controls."
B. Temporary Facilities: Provide temporary barricades and other protection required to prevent injury to people and damage to adjacent buildings and facilities to remain.1. Provide protection to ensure safe passage of people around selective demolition area. 2. Provide temporary weather protection, during interval between selective demolition of existing construction on exterior surfaces and new construction, to prevent water leakage and damage to structure and interior areas.3. Protect walls, ceilings, floors, and other existing finish work that are to remain or that are exposed during selective demolition operations.4. Comply with requirements for temporary enclosures, dust control, heating, and cooling specified in Section 015000 "Temporary Facilities and Controls."
C. Temporary Shoring: Provide and maintain shoring, bracing, and structural supports as required to preserve stability and prevent movement, settlement, or collapse of construction and finishes to remain, and to prevent unexpected or uncontrolled movement or collapse of construction being demolished.
1. Strengthen or add new supports when required during progress of selective demolition.3.4 SELECTIVE DEMOLITION, GENERAL
A. General: Demolish and remove existing construction only to the extent required by new construction and as indicated. Use methods required to complete the Work within limitations of governing regulations and as follows:1. Neatly cut openings and holes plumb, square, and true to dimensions required. Use cutting methods least likely to damage construction to remain or adjoining construction. Use hand tools or small power tools designed for sawing or grinding, not hammering and chopping, to minimize disturbance of adjacent surfaces. Temporarily cover openings to remain.2. Cut or drill from the exposed or finished side into concealed surfaces to avoid marring existing finished surfaces.3. Do not use cutting torches until work area is cleared of flammable materials. At concealed spaces, such as duct and pipe interiors, verify condition and contents of hidden space before starting flame-cutting operations. Maintain portable fire-suppression devices during flame-cutting operations.4. Maintain adequate ventilation when using cutting torches.5. Remove decayed, vermin-infested, or otherwise dangerous or unsuitable materials and promptly dispose of off-site.6. Remove structural framing members and lower to ground by method suitable to avoid free fall and to prevent ground impact or dust generation.7. Locate selective demolition equipment and remove debris and materials so as not to impose excessive loads on supporting walls, floors, or framing.8. Dispose of demolished items and materials promptly.
B. Removed and Reinstalled Items:1. Clean and repair items to functional condition adequate for intended reuse.2. Protect items from damage during storage.3. Reinstall items in locations indicated. Comply with installation requirements for new materials and equipment. Provide connections, supports, and miscellaneous materials necessary to make item functional for use indicated.
C. Existing Items to Remain: Protect construction indicated to remain against damage and soiling during selective demolition. When permitted by Architect, items may be removed to a suitable, protected storage location during selective demolition and cleaned and reinstalled in their original locations after selective demolition operations are complete.
3.5 SELECTIVE DEMOLITION PROCEDURES FOR SPECIFIC MATERIALSA. Concrete: Demolish in small sections. Using power-driven saw, cut concrete to a depth of at least 3/4 inch at junctures with construction to remain. Dislodge concrete from reinforcement at perimeter of areas being demolished, cut reinforcement, and then remove remainder of concrete. Neatly trim openings to dimensions indicated.B. Masonry: Demolish in small sections. Cut masonry at junctures with construction to remain, using power-driven saw, then remove masonry between saw cuts.C. Concrete Slabs-on-Grade: Saw-cut perimeter of area to be demolished, then break up and remove.D. Roofing: Remove no more existing roofing than what can be covered in one day by new roofing and so that building interior remains watertight and weathertight. See Section <Insert Section number and title> for new roofing requirements.
1. Remove existing roof membrane, flashings, copings, and roof accessories.2. Remove existing roofing system down to substrate.
3.6 DISPOSAL OF DEMOLISHED MATERIALSA. General: Except for items or materials indicated to be reused, salvaged, reinstalled, or otherwise indicated to remain Owner's property, remove demolished materials from Project site.
1. Do not allow demolished materials to accumulate on-site.2. Remove and transport debris in a manner that will prevent spillage on adjacent surfaces and areas.3. Remove debris from elevated portions of building by chute, hoist, or other device that will convey debris to grade level in a controlled descent.
B. Burning: Do not burn demolished materials.C. Disposal: Transport demolished materials off Owner's property and legally dispose of them.
3.7 CLEANINGA. Clean adjacent structures and improvements of dust, dirt, and debris caused by selective demolition operations. Return adjacent areas to condition existing before selective demolition operations began.
END OF SECTION 024119
2019-08-06 16:43-05:00
Lauren
Snapshot
Lauren
Snapshot
Lauren
Snapshot
Lauren
Snapshot
Lauren
Snapshot
Lauren
Snapshot
Lauren
Snapshot
WH
WH
WH DN
1 3 4 5 6 7 8 9
A
B
C
1.5 2
16
16
16
7
3
12
16
25
STAIRS AND RAMP TO REMAIN FOR CONSTRUCTION ACCESS; INSTALL TEMP RAILINGS
RAMP TO REMAIN FOR CONSTRUCTION ACCESS, INSTALL TEMP RAILING AS REQUIRED
7
7
7
7
7
7
7
12
23
EXISTING MEP TO REMAIN UNTIL NEW MEP SYSTEMS ARE INSTALLED AND OPERATIONAL, REF MEP
WATERPROOF WALLS BEFORE BACKFILLING
10
26
CLEAR WINDOW WELLS OF DEBRIS CLEAR WINDOW WELLS OF DEBRIS
27 27 27 27 27 27 27
28
28
DEMO NOTES
1REMOVE EXISTING PARTITION OR PORTION THERE OF AND ALL ASSOCIATED TO THE EXTENT REQUIRED FOR NEW SCOPE, PATCH ADJACENT GYP AS REQUIRED. REFERENCE NEW CONSTRUCTION PLANS, TYP.
REMOVE AND SALVAGE EXISTING DOOR, FRAME, TRIM AND HARDWARE ALONG WITH SIDELIGHT W.O. (UNO ON SCHEDULE) FOR REUSE; REF DOOR SCHEDULE AND NEW CONSTRUCTION PLANS FOR NEW LOCATION.
REMOVE EXISTING DOOR AND FRAME ALONG WITH SIDELITE W.O., INFILL WITH GYP AND STUD ASSEMBLY TO MATCH EXISTING PARTITION.
PREPARE ROUGH OPENING FOR NEW OR SALVAGED DOOR AND SIDELITE W.O., REF DOOR SCHEDULE AND NEW CONSTRUCTION PLANS.
CAREFULLY REMOVE EXISTING STOREFRONT, OR WINDOW, AS NOT TO DAMAGE EXISTING MASONRY FACADE.
REMOVE EXISTING MILLWORK AND COUNTERTOPS, CAP ELECTRICAL AND PLUMBING NOT TO BE USED; REF MEP
UNLESS OTHERWISE NOTED, THE DEMOLITION OF THE EXISTING AREA IDENTIFIED TO BE DEMOLISHED IS INTENDED TO BE A COMPLETE INTERIOR REMOVAL OF ALL EXISTING ARCHITECTURAL, MECHANICAL, ELECTRICAL AND PLUMBING COMPONENTS.
REMOVE EXTERIOR CANOPY AND ALL ASSOCIATED INCLUDING COLUMNS AND COLUMN FOUNDATIONS
REMOVE EXISTING DOOR AND FRAME, TO BE INFILLED WITH STOREFRONT GLAZING
DEMO DELIVERY DOCK AND EVERYTHING ON IT INCLUDING BUT NOT LIMITED TO, WALLS AND COOLERS INCLUDING ALL ASSOCIATED ELECTRICAL. WATERPROOF MAIN BUILDING FOUNDATION BEFORE BACKFILLING
REMOVE EXTERIOR SCREEN WALL AND ASSOCIATED FOOTING
REMOVE EXISTING HAND AND GUARDRAIL INCLUDING VERTICAL STEEL PICKETS BETWEEN SWITCHBACKS
REMOVE ALL PLUMBING FIXTURES AND PARTITIONS, CAP PLUMBING AND PATCH FLOOR AS REQUIRED; REF MEP AND NEW CONSTRUCTION PLANS
REMOVE WATER FOUNTAIN
REMOVE ALL FIXTURES AND HANDRAILS, CAP PLUMBING NOT TO BE USED, REF PLUMBING
STAIRS AND RAILINGS TO BE REMOVED AND FLOOR IS TO BE INFILLED, REF STRUCT IN NEW CONSTRUCTION PACKAGE
DEMO EXISTING WOOD LADDER, TO BE REPLACED WITH CODE COMPLIANT LADDER
DEMO CONCRETE SIDEWALK AND CURB, SAW CUT AROUND CANOPY COLUMNS TO REMAIN; PROVIDE $15,000 ALLOWANCE FOR POSSIBLE COLUMN FOUNDATION WORK
REMOVE EXTERIOR GUARDRAIL / HANDRAIL INCLUDING WIDE FLANGE STEEL POSTS W.O.
REMOVE RETAINING WALL AND LANDSCAPING ALONG WITH CONCRETE STAIR AND RAILING, PREP AREA FOR NEW WALL, SIDEWALKS AND LANDSCAPING
REMOVE EXISTING ASPHALT, CURB, INLETS, LIGHT POLES, FIRE HYDRANTS, ETC. AS REQUIRED IN DESIGNATED AREA AROUND BUILDING; REF CIVIL
PREPARE ROUGH OPENING FOR NEW STOREFRONT WINDOW; WINDOWS TO ALIGN WITH EXISTING OPENINGS ON SECOND FLOOR ABOVE
REMOVE WOOD FLOOR INFILL ABOVE STAIR TO BE REMOVED
REMOVE ALL GYP WITH TEXTURED ORANGE PEEL FINISH, TYP.
REMOVE DOOR AND FRAME AND INFILL WITH CMU, TOOTH IN NEW CMU AND COAT EXTERIOR WITH WATERPROOFING
REMOVE EXISTING DOOR, FRAME TO REMAIN
REMOVE WINDOW, PREP OPENING FOR REPLACEMENT WINDOW
REMOVE EXISTING DOOR AND FRAME, PREP OPENING FOR NEW DOOR AND FRAME
REMOVE ROOF EDGE FLASHING, TPO OR EPDM AND ROOF INSULATION, REF MEP FOR ROOF EQUIPMENT DEMO REQUIREMENTS
REMOVE ALL FACADE CLADDING BACK TO STRUCTURE, SALVAGE BRICK FOR ANY PATCH WORK REQUIRED
REMOVE PORTION OF WALL ABOVE STOREFRONT
REMOVE LIGHTING, REF ELECT
REMOVE CANOPY FINISHES, SIGNAGE, AND SOFFIT VENTS
REMOVE EQUIPMENT VENT, PATCH W/ SALVAGED BRICK
GENERAL DEMO NOTES:
1. SALVAGE REMOVED DOORS AND FRAMES, REUSE AS INDICATED. INFORM ARCHITECT OF ANY CONFLICTS OR DISCREPANCIES W/ REUSING EXISTING DOORS AS SCHEDULED. (REF DOOR SCHEDULE)
2. PROTECT ALL EXISTING WORK THAT SURROUNDS THE SCOPE OF WORK, TYPICAL.3. DEMO PLANS SHOW APPROXIMATE SCOPE OF DEMO REQUIREMENTS -
REFERENCE PLANS, SECTIONS, ELEVATIONS, ETC. FOR EXTENT OF NEW CONSTRUCTION; DEMO AS REQUIRED AND NOTIFY ARCHITECT OF ANY DISCREPANCIES.
4. CONTRACTOR TO FIELD VERIFY ALL EXISTING CONDITIONS AND NOTIFY ARCHITECT OF ANY DISCREPANCIES.
5. ALL EXISTING LIGHTING TO BE REMOVED AND REPLACED WITH UPDATED FIXTURES. REF ELECTRICAL.
6. REMOVE ALL FLOOR FINISHES, CEILING GRID AND TILE, AND ABOVE CEILING MECH U.N.O.
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
PHASES LEGEND
DOOR DEMO'D DOOR NEW DOOR IN EXISTING WALL
EXISTING WALL NEW WALL DEMO'D WALL
MILLWORK DEMOLISHED MILLWORK
SHEET TITLE
PROJECT NUMBER
SHEET NUMBER
A
B
C
D
54321
A
B
C
D
FILE
PA
TH:
DA
TE:
DR
AW
N B
Y:
54321
SUBMISSION DATES
500 north broadway suite 200oklahoma city, ok 73102phone: 405.231.3105
schwerdt design grouparchitecture interiors planning2231 sw wanamaker rd suite 303topeka, kansas 66614-4275phone: 785.273.7540
C:\U
sers
\Laure
n\D
ocu
ments
\190121 A
E C
orp
ora
te O
ffic
e (
GageC
ente
r)_ln
fLK
K7H
.rvt
8/6
/2019 2
:44:1
6 P
M
AD
VIS
OR
S E
XC
EL
-G
AG
E C
EN
TE
R C
AM
PU
S
PH
AS
E 1
-D
EM
O P
AC
KA
GE
TO
PE
KA
, KA
NS
AS
666
04
DEMO PLAN - BUILDING A -LOWER LEVEL
190121
D-100
Aut
hor
PROGRESS PRINT ONLY
SCALE: 1/8" = 1'-0"1 DEMO PLAN - BUILDING A - LOWER LEVEL
N
2019-08-06 16:41-05:00
DN
DN
DN
1 3 4 5 6 7 8 9
A
B
C
1.5 2
D-201
1
D-201
2
7
7
7
777
15
16
16
16
5
5
5
5
5
5
5
5
STAIR S1
AS1S
ELEV
AE1
12
9
10
1010
12
18
18
18
11
19 19
FUTURE DEMO BETWEEN GRIDS 4 & 7
FUTURE DEMO BETWEEN GRIDS 4 & 7
1920
20
20
TENANT SPACE A101 TENANT SPACE A102 TENANT SPACE A103 TENANT SPACE A104
TENANT SPACE A105
21
21
1
1
1
1
1
5
28
RESTROOM TO REMAIN UNTIL FUTURE PHASE
28
8 88
1
28
28
DEMO NOTES
1REMOVE EXISTING PARTITION OR PORTION THERE OF AND ALL ASSOCIATED TO THE EXTENT REQUIRED FOR NEW SCOPE, PATCH ADJACENT GYP AS REQUIRED. REFERENCE NEW CONSTRUCTION PLANS, TYP.
REMOVE AND SALVAGE EXISTING DOOR, FRAME, TRIM AND HARDWARE ALONG WITH SIDELIGHT W.O. (UNO ON SCHEDULE) FOR REUSE; REF DOOR SCHEDULE AND NEW CONSTRUCTION PLANS FOR NEW LOCATION.
REMOVE EXISTING DOOR AND FRAME ALONG WITH SIDELITE W.O., INFILL WITH GYP AND STUD ASSEMBLY TO MATCH EXISTING PARTITION.
PREPARE ROUGH OPENING FOR NEW OR SALVAGED DOOR AND SIDELITE W.O., REF DOOR SCHEDULE AND NEW CONSTRUCTION PLANS.
CAREFULLY REMOVE EXISTING STOREFRONT, OR WINDOW, AS NOT TO DAMAGE EXISTING MASONRY FACADE.
REMOVE EXISTING MILLWORK AND COUNTERTOPS, CAP ELECTRICAL AND PLUMBING NOT TO BE USED; REF MEP
UNLESS OTHERWISE NOTED, THE DEMOLITION OF THE EXISTING AREA IDENTIFIED TO BE DEMOLISHED IS INTENDED TO BE A COMPLETE INTERIOR REMOVAL OF ALL EXISTING ARCHITECTURAL, MECHANICAL, ELECTRICAL AND PLUMBING COMPONENTS.
REMOVE EXTERIOR CANOPY AND ALL ASSOCIATED INCLUDING COLUMNS AND COLUMN FOUNDATIONS
REMOVE EXISTING DOOR AND FRAME, TO BE INFILLED WITH STOREFRONT GLAZING
DEMO DELIVERY DOCK AND EVERYTHING ON IT INCLUDING BUT NOT LIMITED TO, WALLS AND COOLERS INCLUDING ALL ASSOCIATED ELECTRICAL. WATERPROOF MAIN BUILDING FOUNDATION BEFORE BACKFILLING
REMOVE EXTERIOR SCREEN WALL AND ASSOCIATED FOOTING
REMOVE EXISTING HAND AND GUARDRAIL INCLUDING VERTICAL STEEL PICKETS BETWEEN SWITCHBACKS
REMOVE ALL PLUMBING FIXTURES AND PARTITIONS, CAP PLUMBING AND PATCH FLOOR AS REQUIRED; REF MEP AND NEW CONSTRUCTION PLANS
REMOVE WATER FOUNTAIN
REMOVE ALL FIXTURES AND HANDRAILS, CAP PLUMBING NOT TO BE USED, REF PLUMBING
STAIRS AND RAILINGS TO BE REMOVED AND FLOOR IS TO BE INFILLED, REF STRUCT IN NEW CONSTRUCTION PACKAGE
DEMO EXISTING WOOD LADDER, TO BE REPLACED WITH CODE COMPLIANT LADDER
DEMO CONCRETE SIDEWALK AND CURB, SAW CUT AROUND CANOPY COLUMNS TO REMAIN; PROVIDE $15,000 ALLOWANCE FOR POSSIBLE COLUMN FOUNDATION WORK
REMOVE EXTERIOR GUARDRAIL / HANDRAIL INCLUDING WIDE FLANGE STEEL POSTS W.O.
REMOVE RETAINING WALL AND LANDSCAPING ALONG WITH CONCRETE STAIR AND RAILING, PREP AREA FOR NEW WALL, SIDEWALKS AND LANDSCAPING
REMOVE EXISTING ASPHALT, CURB, INLETS, LIGHT POLES, FIRE HYDRANTS, ETC. AS REQUIRED IN DESIGNATED AREA AROUND BUILDING; REF CIVIL
PREPARE ROUGH OPENING FOR NEW STOREFRONT WINDOW; WINDOWS TO ALIGN WITH EXISTING OPENINGS ON SECOND FLOOR ABOVE
REMOVE WOOD FLOOR INFILL ABOVE STAIR TO BE REMOVED
REMOVE ALL GYP WITH TEXTURED ORANGE PEEL FINISH, TYP.
REMOVE DOOR AND FRAME AND INFILL WITH CMU, TOOTH IN NEW CMU AND COAT EXTERIOR WITH WATERPROOFING
REMOVE EXISTING DOOR, FRAME TO REMAIN
REMOVE WINDOW, PREP OPENING FOR REPLACEMENT WINDOW
REMOVE EXISTING DOOR AND FRAME, PREP OPENING FOR NEW DOOR AND FRAME
REMOVE ROOF EDGE FLASHING, TPO OR EPDM AND ROOF INSULATION, REF MEP FOR ROOF EQUIPMENT DEMO REQUIREMENTS
REMOVE ALL FACADE CLADDING BACK TO STRUCTURE, SALVAGE BRICK FOR ANY PATCH WORK REQUIRED
REMOVE PORTION OF WALL ABOVE STOREFRONT
REMOVE LIGHTING, REF ELECT
REMOVE CANOPY FINISHES, SIGNAGE, AND SOFFIT VENTS
REMOVE EQUIPMENT VENT, PATCH W/ SALVAGED BRICK
GENERAL DEMO NOTES:
1. SALVAGE REMOVED DOORS AND FRAMES, REUSE AS INDICATED. INFORM ARCHITECT OF ANY CONFLICTS OR DISCREPANCIES W/ REUSING EXISTING DOORS AS SCHEDULED. (REF DOOR SCHEDULE)
2. PROTECT ALL EXISTING WORK THAT SURROUNDS THE SCOPE OF WORK, TYPICAL.3. DEMO PLANS SHOW APPROXIMATE SCOPE OF DEMO REQUIREMENTS -
REFERENCE PLANS, SECTIONS, ELEVATIONS, ETC. FOR EXTENT OF NEW CONSTRUCTION; DEMO AS REQUIRED AND NOTIFY ARCHITECT OF ANY DISCREPANCIES.
4. CONTRACTOR TO FIELD VERIFY ALL EXISTING CONDITIONS AND NOTIFY ARCHITECT OF ANY DISCREPANCIES.
5. ALL EXISTING LIGHTING TO BE REMOVED AND REPLACED WITH UPDATED FIXTURES. REF ELECTRICAL.
6. REMOVE ALL FLOOR FINISHES, CEILING GRID AND TILE, AND ABOVE CEILING MECH U.N.O.
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
PHASES LEGEND
DOOR DEMO'D DOOR NEW DOOR IN EXISTING WALL
EXISTING WALL NEW WALL DEMO'D WALL
MILLWORK DEMOLISHED MILLWORK
SHEET TITLE
PROJECT NUMBER
SHEET NUMBER
A
B
C
D
54321
A
B
C
D
FILE
PA
TH:
DA
TE:
DR
AW
N B
Y:
54321
SUBMISSION DATES
500 north broadway suite 200oklahoma city, ok 73102phone: 405.231.3105
schwerdt design grouparchitecture interiors planning2231 sw wanamaker rd suite 303topeka, kansas 66614-4275phone: 785.273.7540
C:\U
sers
\Laure
n\D
ocu
ments
\190121 A
E C
orp
ora
te O
ffic
e (
GageC
ente
r)_ln
fLK
K7H
.rvt
8/6
/2019 2
:44:1
7 P
M
AD
VIS
OR
S E
XC
EL
-G
AG
E C
EN
TE
R C
AM
PU
S
PH
AS
E 1
-D
EM
O P
AC
KA
GE
TO
PE
KA
, KA
NS
AS
666
04
DEMO PLAN - BUILDING A -FIRST FLOOR
190121
D-101
Aut
hor
PROGRESS PRINT ONLY
SCALE: 1/8" = 1'-0"1 DEMO PLAN - BUILDING A - FIRST FLOOR
2019-08-06 16:41-05:00
Lauren
Snapshot
DW
1 3 4 5 6 7 8 9
A
B
C
1.5
2
MENS
A218CONFERENCE
A213
WOMENS
A219
MGR OFFICE
A216MRG OFFICE
A214HUDDLE
A212HUDDLE
A210HUDDLE
A208COPY/PRINT
A207
BREAK ROOM
A209
1
1
1
ELEC
A217
ELEV
AE2JAN
A203
ELEC
A205
ELEV LOBBY
A204
STAIR S2
AS2S
STAIR N2
AS2N
2
3
4
55555555
2
6
5
5 5
5
5
7
8
N
31
1
1
1
1
13 13
1 1
14
17
12
4
2
12
TENANT SPACE A201
FUTURE DEMO
TENANT SPACE A202TENANT SPACE A203
TENANT SPACE A204
TENANT SPACE A205
7
RELOCATE DOOR TO OTHER SIDE OF COLUMN
RELOCATE DOOR AND SIDELITE
2RELOCATE DOOR
RELOCATE DOOR
3
2
12' - 2 1/4"
242424
24
24
24
DOOR TO REMAIN UNTIL TENANT LEASE IS UP AND SPACE IS VACATED
DEMO NOTES
1REMOVE EXISTING PARTITION OR PORTION THERE OF AND ALL ASSOCIATED TO THE EXTENT REQUIRED FOR NEW SCOPE, PATCH ADJACENT GYP AS REQUIRED. REFERENCE NEW CONSTRUCTION PLANS, TYP.
REMOVE AND SALVAGE EXISTING DOOR, FRAME, TRIM AND HARDWARE ALONG WITH SIDELIGHT W.O. (UNO ON SCHEDULE) FOR REUSE; REF DOOR SCHEDULE AND NEW CONSTRUCTION PLANS FOR NEW LOCATION.
REMOVE EXISTING DOOR AND FRAME ALONG WITH SIDELITE W.O., INFILL WITH GYP AND STUD ASSEMBLY TO MATCH EXISTING PARTITION.
PREPARE ROUGH OPENING FOR NEW OR SALVAGED DOOR AND SIDELITE W.O., REF DOOR SCHEDULE AND NEW CONSTRUCTION PLANS.
CAREFULLY REMOVE EXISTING STOREFRONT, OR WINDOW, AS NOT TO DAMAGE EXISTING MASONRY FACADE.
REMOVE EXISTING MILLWORK AND COUNTERTOPS, CAP ELECTRICAL AND PLUMBING NOT TO BE USED; REF MEP
UNLESS OTHERWISE NOTED, THE DEMOLITION OF THE EXISTING AREA IDENTIFIED TO BE DEMOLISHED IS INTENDED TO BE A COMPLETE INTERIOR REMOVAL OF ALL EXISTING ARCHITECTURAL, MECHANICAL, ELECTRICAL AND PLUMBING COMPONENTS.
REMOVE EXTERIOR CANOPY AND ALL ASSOCIATED INCLUDING COLUMNS AND COLUMN FOUNDATIONS
REMOVE EXISTING DOOR AND FRAME, TO BE INFILLED WITH STOREFRONT GLAZING
DEMO DELIVERY DOCK AND EVERYTHING ON IT INCLUDING BUT NOT LIMITED TO, WALLS AND COOLERS INCLUDING ALL ASSOCIATED ELECTRICAL. WATERPROOF MAIN BUILDING FOUNDATION BEFORE BACKFILLING
REMOVE EXTERIOR SCREEN WALL AND ASSOCIATED FOOTING
REMOVE EXISTING HAND AND GUARDRAIL INCLUDING VERTICAL STEEL PICKETS BETWEEN SWITCHBACKS
REMOVE ALL PLUMBING FIXTURES AND PARTITIONS, CAP PLUMBING AND PATCH FLOOR AS REQUIRED; REF MEP AND NEW CONSTRUCTION PLANS
REMOVE WATER FOUNTAIN
REMOVE ALL FIXTURES AND HANDRAILS, CAP PLUMBING NOT TO BE USED, REF PLUMBING
STAIRS AND RAILINGS TO BE REMOVED AND FLOOR IS TO BE INFILLED, REF STRUCT IN NEW CONSTRUCTION PACKAGE
DEMO EXISTING WOOD LADDER, TO BE REPLACED WITH CODE COMPLIANT LADDER
DEMO CONCRETE SIDEWALK AND CURB, SAW CUT AROUND CANOPY COLUMNS TO REMAIN; PROVIDE $15,000 ALLOWANCE FOR POSSIBLE COLUMN FOUNDATION WORK
REMOVE EXTERIOR GUARDRAIL / HANDRAIL INCLUDING WIDE FLANGE STEEL POSTS W.O.
REMOVE RETAINING WALL AND LANDSCAPING ALONG WITH CONCRETE STAIR AND RAILING, PREP AREA FOR NEW WALL, SIDEWALKS AND LANDSCAPING
REMOVE EXISTING ASPHALT, CURB, INLETS, LIGHT POLES, FIRE HYDRANTS, ETC. AS REQUIRED IN DESIGNATED AREA AROUND BUILDING; REF CIVIL
PREPARE ROUGH OPENING FOR NEW STOREFRONT WINDOW; WINDOWS TO ALIGN WITH EXISTING OPENINGS ON SECOND FLOOR ABOVE
REMOVE WOOD FLOOR INFILL ABOVE STAIR TO BE REMOVED
REMOVE ALL GYP WITH TEXTURED ORANGE PEEL FINISH, TYP.
REMOVE DOOR AND FRAME AND INFILL WITH CMU, TOOTH IN NEW CMU AND COAT EXTERIOR WITH WATERPROOFING
REMOVE EXISTING DOOR, FRAME TO REMAIN
REMOVE WINDOW, PREP OPENING FOR REPLACEMENT WINDOW
REMOVE EXISTING DOOR AND FRAME, PREP OPENING FOR NEW DOOR AND FRAME
REMOVE ROOF EDGE FLASHING, TPO OR EPDM AND ROOF INSULATION, REF MEP FOR ROOF EQUIPMENT DEMO REQUIREMENTS
REMOVE ALL FACADE CLADDING BACK TO STRUCTURE, SALVAGE BRICK FOR ANY PATCH WORK REQUIRED
REMOVE PORTION OF WALL ABOVE STOREFRONT
REMOVE LIGHTING, REF ELECT
REMOVE CANOPY FINISHES, SIGNAGE, AND SOFFIT VENTS
REMOVE EQUIPMENT VENT, PATCH W/ SALVAGED BRICK
GENERAL DEMO NOTES:
1. SALVAGE REMOVED DOORS AND FRAMES, REUSE AS INDICATED. INFORM ARCHITECT OF ANY CONFLICTS OR DISCREPANCIES W/ REUSING EXISTING DOORS AS SCHEDULED. (REF DOOR SCHEDULE)
2. PROTECT ALL EXISTING WORK THAT SURROUNDS THE SCOPE OF WORK, TYPICAL.3. DEMO PLANS SHOW APPROXIMATE SCOPE OF DEMO REQUIREMENTS -
REFERENCE PLANS, SECTIONS, ELEVATIONS, ETC. FOR EXTENT OF NEW CONSTRUCTION; DEMO AS REQUIRED AND NOTIFY ARCHITECT OF ANY DISCREPANCIES.
4. CONTRACTOR TO FIELD VERIFY ALL EXISTING CONDITIONS AND NOTIFY ARCHITECT OF ANY DISCREPANCIES.
5. ALL EXISTING LIGHTING TO BE REMOVED AND REPLACED WITH UPDATED FIXTURES. REF ELECTRICAL.
6. REMOVE ALL FLOOR FINISHES, CEILING GRID AND TILE, AND ABOVE CEILING MECH U.N.O.
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
PHASES LEGEND
DOOR DEMO'D DOOR NEW DOOR IN EXISTING WALL
EXISTING WALL NEW WALL DEMO'D WALL
MILLWORK DEMOLISHED MILLWORK
SHEET TITLE
PROJECT NUMBER
SHEET NUMBER
A
B
C
D
54321
A
B
C
D
FILE
PA
TH:
DA
TE:
DR
AW
N B
Y:
54321
SUBMISSION DATES
500 north broadway suite 200oklahoma city, ok 73102phone: 405.231.3105
schwerdt design grouparchitecture interiors planning2231 sw wanamaker rd suite 303topeka, kansas 66614-4275phone: 785.273.7540
C:\U
sers
\Laure
n\D
ocu
ments
\190121 A
E C
orp
ora
te O
ffic
e (
GageC
ente
r)_ln
fLK
K7H
.rvt
8/6
/2019 2
:44:1
8 P
M
AD
VIS
OR
S E
XC
EL
-G
AG
E C
EN
TE
R C
AM
PU
S
PH
AS
E 1
-D
EM
O P
AC
KA
GE
TO
PE
KA
, KA
NS
AS
666
04
DEMO PLAN - BUILDING A -SECOND FLOOR
190121
D-102
Aut
hor
PROGRESS PRINT ONLY
SCALE: 1/8" = 1'-0"1 DEMO PLAN - BUILDING A - SECOND FLOOR
2019-08-06 16:44-05:00
A
B
C
D
E
2 3 4 5 6
D-203
1
D-203
2
D-2041
N
NO WORK THIS AREA
7
7
7
7
TENANT SPACE K101
TENANT SPACE K102
TENANT SPACE K103
TENANT SPACE K104
5
22
22
22
22
22
22
TENANT SPACE K105
2
KEEP ACCESS TO RESTROOMS AVAILABLE TO TENANT K102 SPACE UNTIL NEW RESTROOMS ARE BUILT.
18
21
115 5 5
TENANT OCCUPIED SPACE, COORDINATE SCHEDULE OF WINDOW REPLACEMENT W/ OWNER
19
20' - 0 1/2"
DEMO VESTIBULE AND ALL ASSOCIATED, INCLUDING PLANTERS
225
5
5
REMOVE DOORS AND FRAME
D-204 2
DEMO NOTES
1REMOVE EXISTING PARTITION OR PORTION THERE OF AND ALL ASSOCIATED TO THE EXTENT REQUIRED FOR NEW SCOPE, PATCH ADJACENT GYP AS REQUIRED. REFERENCE NEW CONSTRUCTION PLANS, TYP.
REMOVE AND SALVAGE EXISTING DOOR, FRAME, TRIM AND HARDWARE ALONG WITH SIDELIGHT W.O. (UNO ON SCHEDULE) FOR REUSE; REF DOOR SCHEDULE AND NEW CONSTRUCTION PLANS FOR NEW LOCATION.
REMOVE EXISTING DOOR AND FRAME ALONG WITH SIDELITE W.O., INFILL WITH GYP AND STUD ASSEMBLY TO MATCH EXISTING PARTITION.
PREPARE ROUGH OPENING FOR NEW OR SALVAGED DOOR AND SIDELITE W.O., REF DOOR SCHEDULE AND NEW CONSTRUCTION PLANS.
CAREFULLY REMOVE EXISTING STOREFRONT, OR WINDOW, AS NOT TO DAMAGE EXISTING MASONRY FACADE.
REMOVE EXISTING MILLWORK AND COUNTERTOPS, CAP ELECTRICAL AND PLUMBING NOT TO BE USED; REF MEP
UNLESS OTHERWISE NOTED, THE DEMOLITION OF THE EXISTING AREA IDENTIFIED TO BE DEMOLISHED IS INTENDED TO BE A COMPLETE INTERIOR REMOVAL OF ALL EXISTING ARCHITECTURAL, MECHANICAL, ELECTRICAL AND PLUMBING COMPONENTS.
REMOVE EXTERIOR CANOPY AND ALL ASSOCIATED INCLUDING COLUMNS AND COLUMN FOUNDATIONS
REMOVE EXISTING DOOR AND FRAME, TO BE INFILLED WITH STOREFRONT GLAZING
DEMO DELIVERY DOCK AND EVERYTHING ON IT INCLUDING BUT NOT LIMITED TO, WALLS AND COOLERS INCLUDING ALL ASSOCIATED ELECTRICAL. WATERPROOF MAIN BUILDING FOUNDATION BEFORE BACKFILLING
REMOVE EXTERIOR SCREEN WALL AND ASSOCIATED FOOTING
REMOVE EXISTING HAND AND GUARDRAIL INCLUDING VERTICAL STEEL PICKETS BETWEEN SWITCHBACKS
REMOVE ALL PLUMBING FIXTURES AND PARTITIONS, CAP PLUMBING AND PATCH FLOOR AS REQUIRED; REF MEP AND NEW CONSTRUCTION PLANS
REMOVE WATER FOUNTAIN
REMOVE ALL FIXTURES AND HANDRAILS, CAP PLUMBING NOT TO BE USED, REF PLUMBING
STAIRS AND RAILINGS TO BE REMOVED AND FLOOR IS TO BE INFILLED, REF STRUCT IN NEW CONSTRUCTION PACKAGE
DEMO EXISTING WOOD LADDER, TO BE REPLACED WITH CODE COMPLIANT LADDER
DEMO CONCRETE SIDEWALK AND CURB, SAW CUT AROUND CANOPY COLUMNS TO REMAIN; PROVIDE $15,000 ALLOWANCE FOR POSSIBLE COLUMN FOUNDATION WORK
REMOVE EXTERIOR GUARDRAIL / HANDRAIL INCLUDING WIDE FLANGE STEEL POSTS W.O.
REMOVE RETAINING WALL AND LANDSCAPING ALONG WITH CONCRETE STAIR AND RAILING, PREP AREA FOR NEW WALL, SIDEWALKS AND LANDSCAPING
REMOVE EXISTING ASPHALT, CURB, INLETS, LIGHT POLES, FIRE HYDRANTS, ETC. AS REQUIRED IN DESIGNATED AREA AROUND BUILDING; REF CIVIL
PREPARE ROUGH OPENING FOR NEW STOREFRONT WINDOW; WINDOWS TO ALIGN WITH EXISTING OPENINGS ON SECOND FLOOR ABOVE
REMOVE WOOD FLOOR INFILL ABOVE STAIR TO BE REMOVED
REMOVE ALL GYP WITH TEXTURED ORANGE PEEL FINISH, TYP.
REMOVE DOOR AND FRAME AND INFILL WITH CMU, TOOTH IN NEW CMU AND COAT EXTERIOR WITH WATERPROOFING
REMOVE EXISTING DOOR, FRAME TO REMAIN
REMOVE WINDOW, PREP OPENING FOR REPLACEMENT WINDOW
REMOVE EXISTING DOOR AND FRAME, PREP OPENING FOR NEW DOOR AND FRAME
REMOVE ROOF EDGE FLASHING, TPO OR EPDM AND ROOF INSULATION, REF MEP FOR ROOF EQUIPMENT DEMO REQUIREMENTS
REMOVE ALL FACADE CLADDING BACK TO STRUCTURE, SALVAGE BRICK FOR ANY PATCH WORK REQUIRED
REMOVE PORTION OF WALL ABOVE STOREFRONT
REMOVE LIGHTING, REF ELECT
REMOVE CANOPY FINISHES, SIGNAGE, AND SOFFIT VENTS
REMOVE EQUIPMENT VENT, PATCH W/ SALVAGED BRICK
GENERAL DEMO NOTES:
1. SALVAGE REMOVED DOORS AND FRAMES, REUSE AS INDICATED. INFORM ARCHITECT OF ANY CONFLICTS OR DISCREPANCIES W/ REUSING EXISTING DOORS AS SCHEDULED. (REF DOOR SCHEDULE)
2. PROTECT ALL EXISTING WORK THAT SURROUNDS THE SCOPE OF WORK, TYPICAL.3. DEMO PLANS SHOW APPROXIMATE SCOPE OF DEMO REQUIREMENTS -
REFERENCE PLANS, SECTIONS, ELEVATIONS, ETC. FOR EXTENT OF NEW CONSTRUCTION; DEMO AS REQUIRED AND NOTIFY ARCHITECT OF ANY DISCREPANCIES.
4. CONTRACTOR TO FIELD VERIFY ALL EXISTING CONDITIONS AND NOTIFY ARCHITECT OF ANY DISCREPANCIES.
5. ALL EXISTING LIGHTING TO BE REMOVED AND REPLACED WITH UPDATED FIXTURES. REF ELECTRICAL.
6. REMOVE ALL FLOOR FINISHES, CEILING GRID AND TILE, AND ABOVE CEILING MECH U.N.O.
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
PHASES LEGEND
DOOR DEMO'D DOOR NEW DOOR IN EXISTING WALL
EXISTING WALL NEW WALL DEMO'D WALL
MILLWORK DEMOLISHED MILLWORK
SHEET TITLE
PROJECT NUMBER
SHEET NUMBER
A
B
C
D
54321
A
B
C
D
FILE
PA
TH:
DA
TE:
DR
AW
N B
Y:
54321
SUBMISSION DATES
500 north broadway suite 200oklahoma city, ok 73102phone: 405.231.3105
schwerdt design grouparchitecture interiors planning2231 sw wanamaker rd suite 303topeka, kansas 66614-4275phone: 785.273.7540
C:\U
sers
\Laure
n\D
ocu
ments
\190121 A
E C
orp
ora
te O
ffic
e (
GageC
ente
r)_ln
fLK
K7H
.rvt
8/6
/2019 2
:44:1
9 P
M
AD
VIS
OR
S E
XC
EL
-G
AG
E C
EN
TE
R C
AM
PU
S
PH
AS
E 1
-D
EM
O P
AC
KA
GE
TO
PE
KA
, KA
NS
AS
666
04
DEMO PLAN - BUILDING K -FIRST FLOOR
190121
D-103
Aut
hor
PROGRESS PRINT ONLY
SCALE: 1/8" = 1'-0"1 BUILDING K - DEMO FIRST FLOOR PLAN
2019-08-06 16:44-05:00
UP
DN
A
B
C
D
E
2 3 4 5 6
D-203
1
D-203
2
D-2041
N
1 1 1
1
1
1
16' - 0"
2 2 2 2
2
RE
LOC
ATE
DO
OR
0' -
8"
1
1
RELOCATE
RELOCATERELOCATE
RELOCATE
4' - 2"7' - 9 1/4"4' - 2" 20' - 5"
2
44
4
1
1
1 1
1
1
4
OFFICE
K204
CONFERENCE
K203
RECEPTION
K202
OPEN OFFICE
K223
OFFICE
K205OFFICE
K207 OFFICE
K208
MGR
K210 OFFICE
K211SCRUM
K212 OFFICE
K213
BREAK
K214
ELEC
K216STORAGE
K215
OFFICE
K217
OFFICE
K218
TECH LAB
K219
OPEN OFFICE
K220
OPEN OFFICE
K221
STORAGE
K224
MECH
K225
BUSINESS OCC
TENANT
K132
BREAK
133
STAIR 2W
KS2W
CONFERENCE
K222
NO WORK THIS AREA
29 2929
6
6
SALVAGE DOOR, TO BE RELOCATED TO CONFERENCE K203, REF NEW CONSTRUCTION PLANS
COMMON
CORRIDOR
K201
5
5
5
5
5
5
5
5
5
5
5
5
28 28
5
1
1' - 6"5' - 0"
28
D-204 2
DEMO NOTES
1REMOVE EXISTING PARTITION OR PORTION THERE OF AND ALL ASSOCIATED TO THE EXTENT REQUIRED FOR NEW SCOPE, PATCH ADJACENT GYP AS REQUIRED. REFERENCE NEW CONSTRUCTION PLANS, TYP.
REMOVE AND SALVAGE EXISTING DOOR, FRAME, TRIM AND HARDWARE ALONG WITH SIDELIGHT W.O. (UNO ON SCHEDULE) FOR REUSE; REF DOOR SCHEDULE AND NEW CONSTRUCTION PLANS FOR NEW LOCATION.
REMOVE EXISTING DOOR AND FRAME ALONG WITH SIDELITE W.O., INFILL WITH GYP AND STUD ASSEMBLY TO MATCH EXISTING PARTITION.
PREPARE ROUGH OPENING FOR NEW OR SALVAGED DOOR AND SIDELITE W.O., REF DOOR SCHEDULE AND NEW CONSTRUCTION PLANS.
CAREFULLY REMOVE EXISTING STOREFRONT, OR WINDOW, AS NOT TO DAMAGE EXISTING MASONRY FACADE.
REMOVE EXISTING MILLWORK AND COUNTERTOPS, CAP ELECTRICAL AND PLUMBING NOT TO BE USED; REF MEP
UNLESS OTHERWISE NOTED, THE DEMOLITION OF THE EXISTING AREA IDENTIFIED TO BE DEMOLISHED IS INTENDED TO BE A COMPLETE INTERIOR REMOVAL OF ALL EXISTING ARCHITECTURAL, MECHANICAL, ELECTRICAL AND PLUMBING COMPONENTS.
REMOVE EXTERIOR CANOPY AND ALL ASSOCIATED INCLUDING COLUMNS AND COLUMN FOUNDATIONS
REMOVE EXISTING DOOR AND FRAME, TO BE INFILLED WITH STOREFRONT GLAZING
DEMO DELIVERY DOCK AND EVERYTHING ON IT INCLUDING BUT NOT LIMITED TO, WALLS AND COOLERS INCLUDING ALL ASSOCIATED ELECTRICAL. WATERPROOF MAIN BUILDING FOUNDATION BEFORE BACKFILLING
REMOVE EXTERIOR SCREEN WALL AND ASSOCIATED FOOTING
REMOVE EXISTING HAND AND GUARDRAIL INCLUDING VERTICAL STEEL PICKETS BETWEEN SWITCHBACKS
REMOVE ALL PLUMBING FIXTURES AND PARTITIONS, CAP PLUMBING AND PATCH FLOOR AS REQUIRED; REF MEP AND NEW CONSTRUCTION PLANS
REMOVE WATER FOUNTAIN
REMOVE ALL FIXTURES AND HANDRAILS, CAP PLUMBING NOT TO BE USED, REF PLUMBING
STAIRS AND RAILINGS TO BE REMOVED AND FLOOR IS TO BE INFILLED, REF STRUCT IN NEW CONSTRUCTION PACKAGE
DEMO EXISTING WOOD LADDER, TO BE REPLACED WITH CODE COMPLIANT LADDER
DEMO CONCRETE SIDEWALK AND CURB, SAW CUT AROUND CANOPY COLUMNS TO REMAIN; PROVIDE $15,000 ALLOWANCE FOR POSSIBLE COLUMN FOUNDATION WORK
REMOVE EXTERIOR GUARDRAIL / HANDRAIL INCLUDING WIDE FLANGE STEEL POSTS W.O.
REMOVE RETAINING WALL AND LANDSCAPING ALONG WITH CONCRETE STAIR AND RAILING, PREP AREA FOR NEW WALL, SIDEWALKS AND LANDSCAPING
REMOVE EXISTING ASPHALT, CURB, INLETS, LIGHT POLES, FIRE HYDRANTS, ETC. AS REQUIRED IN DESIGNATED AREA AROUND BUILDING; REF CIVIL
PREPARE ROUGH OPENING FOR NEW STOREFRONT WINDOW; WINDOWS TO ALIGN WITH EXISTING OPENINGS ON SECOND FLOOR ABOVE
REMOVE WOOD FLOOR INFILL ABOVE STAIR TO BE REMOVED
REMOVE ALL GYP WITH TEXTURED ORANGE PEEL FINISH, TYP.
REMOVE DOOR AND FRAME AND INFILL WITH CMU, TOOTH IN NEW CMU AND COAT EXTERIOR WITH WATERPROOFING
REMOVE EXISTING DOOR, FRAME TO REMAIN
REMOVE WINDOW, PREP OPENING FOR REPLACEMENT WINDOW
REMOVE EXISTING DOOR AND FRAME, PREP OPENING FOR NEW DOOR AND FRAME
REMOVE ROOF EDGE FLASHING, TPO OR EPDM AND ROOF INSULATION, REF MEP FOR ROOF EQUIPMENT DEMO REQUIREMENTS
REMOVE ALL FACADE CLADDING BACK TO STRUCTURE, SALVAGE BRICK FOR ANY PATCH WORK REQUIRED
REMOVE PORTION OF WALL ABOVE STOREFRONT
REMOVE LIGHTING, REF ELECT
REMOVE CANOPY FINISHES, SIGNAGE, AND SOFFIT VENTS
REMOVE EQUIPMENT VENT, PATCH W/ SALVAGED BRICK
GENERAL DEMO NOTES:
1. SALVAGE REMOVED DOORS AND FRAMES, REUSE AS INDICATED. INFORM ARCHITECT OF ANY CONFLICTS OR DISCREPANCIES W/ REUSING EXISTING DOORS AS SCHEDULED. (REF DOOR SCHEDULE)
2. PROTECT ALL EXISTING WORK THAT SURROUNDS THE SCOPE OF WORK, TYPICAL.3. DEMO PLANS SHOW APPROXIMATE SCOPE OF DEMO REQUIREMENTS -
REFERENCE PLANS, SECTIONS, ELEVATIONS, ETC. FOR EXTENT OF NEW CONSTRUCTION; DEMO AS REQUIRED AND NOTIFY ARCHITECT OF ANY DISCREPANCIES.
4. CONTRACTOR TO FIELD VERIFY ALL EXISTING CONDITIONS AND NOTIFY ARCHITECT OF ANY DISCREPANCIES.
5. ALL EXISTING LIGHTING TO BE REMOVED AND REPLACED WITH UPDATED FIXTURES. REF ELECTRICAL.
6. REMOVE ALL FLOOR FINISHES, CEILING GRID AND TILE, AND ABOVE CEILING MECH U.N.O.
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
PHASES LEGEND
DOOR DEMO'D DOOR NEW DOOR IN EXISTING WALL
EXISTING WALL NEW WALL DEMO'D WALL
MILLWORK DEMOLISHED MILLWORK
SHEET TITLE
PROJECT NUMBER
SHEET NUMBER
A
B
C
D
54321
A
B
C
D
FILE
PA
TH:
DA
TE:
DR
AW
N B
Y:
54321
SUBMISSION DATES
500 north broadway suite 200oklahoma city, ok 73102phone: 405.231.3105
schwerdt design grouparchitecture interiors planning2231 sw wanamaker rd suite 303topeka, kansas 66614-4275phone: 785.273.7540
C:\U
sers
\Laure
n\D
ocu
ments
\190121 A
E C
orp
ora
te O
ffic
e (
GageC
ente
r)_ln
fLK
K7H
.rvt
8/6
/2019 2
:44:2
0 P
M
AD
VIS
OR
S E
XC
EL
-G
AG
E C
EN
TE
R C
AM
PU
S
PH
AS
E 1
-D
EM
O P
AC
KA
GE
TO
PE
KA
, KA
NS
AS
666
04
DEMO PLAN - BUILDING K -SECOND FLOOR
190121
D-104
Aut
hor
PROGRESS PRINT ONLY
SCALE: 1/8" = 1'-0"1 BUILDING K - DEMO SECOND FLOOR PLAN
2019-08-06 16:42-05:00
1 3 4 5 6 7 8 92
888 8
29
FACADE DEMO THIS AREA INDICATED BY DIAGONAL DOWN HATCH TO BE COMPLETED IN A FUTURE PHASE
30
30 30 30 30
30 30 30
13456789 1.52
19' - 1 1/2" 20' - 0" 20' - 0" 20' - 0" 20' - 0" 20' - 0" 20' - 0" 19' - 1 1/2"
9
10
10
19 1919
11
55
5
10
29 29
FUTURE DEMO THIS AREA INDICATED WITH DIAGONAL DOWN HATCH
31 31 31 31
55555
20
32 32 32 32 3232
32 3232
34 34
34
DEMO NOTES
1REMOVE EXISTING PARTITION OR PORTION THERE OF AND ALL ASSOCIATED TO THE EXTENT REQUIRED FOR NEW SCOPE, PATCH ADJACENT GYP AS REQUIRED. REFERENCE NEW CONSTRUCTION PLANS, TYP.
REMOVE AND SALVAGE EXISTING DOOR, FRAME, TRIM AND HARDWARE ALONG WITH SIDELIGHT W.O. (UNO ON SCHEDULE) FOR REUSE; REF DOOR SCHEDULE AND NEW CONSTRUCTION PLANS FOR NEW LOCATION.
REMOVE EXISTING DOOR AND FRAME ALONG WITH SIDELITE W.O., INFILL WITH GYP AND STUD ASSEMBLY TO MATCH EXISTING PARTITION.
PREPARE ROUGH OPENING FOR NEW OR SALVAGED DOOR AND SIDELITE W.O., REF DOOR SCHEDULE AND NEW CONSTRUCTION PLANS.
CAREFULLY REMOVE EXISTING STOREFRONT, OR WINDOW, AS NOT TO DAMAGE EXISTING MASONRY FACADE.
REMOVE EXISTING MILLWORK AND COUNTERTOPS, CAP ELECTRICAL AND PLUMBING NOT TO BE USED; REF MEP
UNLESS OTHERWISE NOTED, THE DEMOLITION OF THE EXISTING AREA IDENTIFIED TO BE DEMOLISHED IS INTENDED TO BE A COMPLETE INTERIOR REMOVAL OF ALL EXISTING ARCHITECTURAL, MECHANICAL, ELECTRICAL AND PLUMBING COMPONENTS.
REMOVE EXTERIOR CANOPY AND ALL ASSOCIATED INCLUDING COLUMNS AND COLUMN FOUNDATIONS
REMOVE EXISTING DOOR AND FRAME, TO BE INFILLED WITH STOREFRONT GLAZING
DEMO DELIVERY DOCK AND EVERYTHING ON IT INCLUDING BUT NOT LIMITED TO, WALLS AND COOLERS INCLUDING ALL ASSOCIATED ELECTRICAL. WATERPROOF MAIN BUILDING FOUNDATION BEFORE BACKFILLING
REMOVE EXTERIOR SCREEN WALL AND ASSOCIATED FOOTING
REMOVE EXISTING HAND AND GUARDRAIL INCLUDING VERTICAL STEEL PICKETS BETWEEN SWITCHBACKS
REMOVE ALL PLUMBING FIXTURES AND PARTITIONS, CAP PLUMBING AND PATCH FLOOR AS REQUIRED; REF MEP AND NEW CONSTRUCTION PLANS
REMOVE WATER FOUNTAIN
REMOVE ALL FIXTURES AND HANDRAILS, CAP PLUMBING NOT TO BE USED, REF PLUMBING
STAIRS AND RAILINGS TO BE REMOVED AND FLOOR IS TO BE INFILLED, REF STRUCT IN NEW CONSTRUCTION PACKAGE
DEMO EXISTING WOOD LADDER, TO BE REPLACED WITH CODE COMPLIANT LADDER
DEMO CONCRETE SIDEWALK AND CURB, SAW CUT AROUND CANOPY COLUMNS TO REMAIN; PROVIDE $15,000 ALLOWANCE FOR POSSIBLE COLUMN FOUNDATION WORK
REMOVE EXTERIOR GUARDRAIL / HANDRAIL INCLUDING WIDE FLANGE STEEL POSTS W.O.
REMOVE RETAINING WALL AND LANDSCAPING ALONG WITH CONCRETE STAIR AND RAILING, PREP AREA FOR NEW WALL, SIDEWALKS AND LANDSCAPING
REMOVE EXISTING ASPHALT, CURB, INLETS, LIGHT POLES, FIRE HYDRANTS, ETC. AS REQUIRED IN DESIGNATED AREA AROUND BUILDING; REF CIVIL
PREPARE ROUGH OPENING FOR NEW STOREFRONT WINDOW; WINDOWS TO ALIGN WITH EXISTING OPENINGS ON SECOND FLOOR ABOVE
REMOVE WOOD FLOOR INFILL ABOVE STAIR TO BE REMOVED
REMOVE ALL GYP WITH TEXTURED ORANGE PEEL FINISH, TYP.
REMOVE DOOR AND FRAME AND INFILL WITH CMU, TOOTH IN NEW CMU AND COAT EXTERIOR WITH WATERPROOFING
REMOVE EXISTING DOOR, FRAME TO REMAIN
REMOVE WINDOW, PREP OPENING FOR REPLACEMENT WINDOW
REMOVE EXISTING DOOR AND FRAME, PREP OPENING FOR NEW DOOR AND FRAME
REMOVE ROOF EDGE FLASHING, TPO OR EPDM AND ROOF INSULATION, REF MEP FOR ROOF EQUIPMENT DEMO REQUIREMENTS
REMOVE ALL FACADE CLADDING BACK TO STRUCTURE, SALVAGE BRICK FOR ANY PATCH WORK REQUIRED
REMOVE PORTION OF WALL ABOVE STOREFRONT
REMOVE LIGHTING, REF ELECT
REMOVE CANOPY FINISHES, SIGNAGE, AND SOFFIT VENTS
REMOVE EQUIPMENT VENT, PATCH W/ SALVAGED BRICK
GENERAL DEMO NOTES:
1. SALVAGE REMOVED DOORS AND FRAMES, REUSE AS INDICATED. INFORM ARCHITECT OF ANY CONFLICTS OR DISCREPANCIES W/ REUSING EXISTING DOORS AS SCHEDULED. (REF DOOR SCHEDULE)
2. PROTECT ALL EXISTING WORK THAT SURROUNDS THE SCOPE OF WORK, TYPICAL.3. DEMO PLANS SHOW APPROXIMATE SCOPE OF DEMO REQUIREMENTS -
REFERENCE PLANS, SECTIONS, ELEVATIONS, ETC. FOR EXTENT OF NEW CONSTRUCTION; DEMO AS REQUIRED AND NOTIFY ARCHITECT OF ANY DISCREPANCIES.
4. CONTRACTOR TO FIELD VERIFY ALL EXISTING CONDITIONS AND NOTIFY ARCHITECT OF ANY DISCREPANCIES.
5. ALL EXISTING LIGHTING TO BE REMOVED AND REPLACED WITH UPDATED FIXTURES. REF ELECTRICAL.
6. REMOVE ALL FLOOR FINISHES, CEILING GRID AND TILE, AND ABOVE CEILING MECH U.N.O.
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34SHEET TITLE
PROJECT NUMBER
SHEET NUMBER
A
B
C
D
54321
A
B
C
D
FILE
PA
TH:
DA
TE:
DR
AW
N B
Y:
54321
SUBMISSION DATES
500 north broadway suite 200oklahoma city, ok 73102phone: 405.231.3105
schwerdt design grouparchitecture interiors planning2231 sw wanamaker rd suite 303topeka, kansas 66614-4275phone: 785.273.7540
C:\U
sers
\Laure
n\D
ocu
ments
\190121 A
E C
orp
ora
te O
ffic
e (
GageC
ente
r)_ln
fLK
K7H
.rvt
8/6
/2019 2
:44:2
4 P
M
AD
VIS
OR
S E
XC
EL
-G
AG
E C
EN
TE
R C
AM
PU
S
PH
AS
E 1
-D
EM
O P
AC
KA
GE
TO
PE
KA
, KA
NS
AS
666
04
EXTERIOR DEMOELEVATIONS - BUILDING A
190121
D-201
Aut
hor
PROGRESS PRINT ONLY
SCALE: 1/8" = 1'-0"1 EAST DEMO ELEVATION
SCALE: 1/8" = 1'-0"2 WEST DEMO ELEVATION
2019-08-06 16:42-05:00
DEMO NOTES
1REMOVE EXISTING PARTITION OR PORTION THERE OF AND ALL ASSOCIATED TO THE EXTENT REQUIRED FOR NEW SCOPE, PATCH ADJACENT GYP AS REQUIRED. REFERENCE NEW CONSTRUCTION PLANS, TYP.
REMOVE AND SALVAGE EXISTING DOOR, FRAME, TRIM AND HARDWARE ALONG WITH SIDELIGHT W.O. (UNO ON SCHEDULE) FOR REUSE; REF DOOR SCHEDULE AND NEW CONSTRUCTION PLANS FOR NEW LOCATION.
REMOVE EXISTING DOOR AND FRAME ALONG WITH SIDELITE W.O., INFILL WITH GYP AND STUD ASSEMBLY TO MATCH EXISTING PARTITION.
PREPARE ROUGH OPENING FOR NEW OR SALVAGED DOOR AND SIDELITE W.O., REF DOOR SCHEDULE AND NEW CONSTRUCTION PLANS.
CAREFULLY REMOVE EXISTING STOREFRONT, OR WINDOW, AS NOT TO DAMAGE EXISTING MASONRY FACADE.
REMOVE EXISTING MILLWORK AND COUNTERTOPS, CAP ELECTRICAL AND PLUMBING NOT TO BE USED; REF MEP
UNLESS OTHERWISE NOTED, THE DEMOLITION OF THE EXISTING AREA IDENTIFIED TO BE DEMOLISHED IS INTENDED TO BE A COMPLETE INTERIOR REMOVAL OF ALL EXISTING ARCHITECTURAL, MECHANICAL, ELECTRICAL AND PLUMBING COMPONENTS.
REMOVE EXTERIOR CANOPY AND ALL ASSOCIATED INCLUDING COLUMNS AND COLUMN FOUNDATIONS
REMOVE EXISTING DOOR AND FRAME, TO BE INFILLED WITH STOREFRONT GLAZING
DEMO DELIVERY DOCK AND EVERYTHING ON IT INCLUDING BUT NOT LIMITED TO, WALLS AND COOLERS INCLUDING ALL ASSOCIATED ELECTRICAL. WATERPROOF MAIN BUILDING FOUNDATION BEFORE BACKFILLING
REMOVE EXTERIOR SCREEN WALL AND ASSOCIATED FOOTING
REMOVE EXISTING HAND AND GUARDRAIL INCLUDING VERTICAL STEEL PICKETS BETWEEN SWITCHBACKS
REMOVE ALL PLUMBING FIXTURES AND PARTITIONS, CAP PLUMBING AND PATCH FLOOR AS REQUIRED; REF MEP AND NEW CONSTRUCTION PLANS
REMOVE WATER FOUNTAIN
REMOVE ALL FIXTURES AND HANDRAILS, CAP PLUMBING NOT TO BE USED, REF PLUMBING
STAIRS AND RAILINGS TO BE REMOVED AND FLOOR IS TO BE INFILLED, REF STRUCT IN NEW CONSTRUCTION PACKAGE
DEMO EXISTING WOOD LADDER, TO BE REPLACED WITH CODE COMPLIANT LADDER
DEMO CONCRETE SIDEWALK AND CURB, SAW CUT AROUND CANOPY COLUMNS TO REMAIN; PROVIDE $15,000 ALLOWANCE FOR POSSIBLE COLUMN FOUNDATION WORK
REMOVE EXTERIOR GUARDRAIL / HANDRAIL INCLUDING WIDE FLANGE STEEL POSTS W.O.
REMOVE RETAINING WALL AND LANDSCAPING ALONG WITH CONCRETE STAIR AND RAILING, PREP AREA FOR NEW WALL, SIDEWALKS AND LANDSCAPING
REMOVE EXISTING ASPHALT, CURB, INLETS, LIGHT POLES, FIRE HYDRANTS, ETC. AS REQUIRED IN DESIGNATED AREA AROUND BUILDING; REF CIVIL
PREPARE ROUGH OPENING FOR NEW STOREFRONT WINDOW; WINDOWS TO ALIGN WITH EXISTING OPENINGS ON SECOND FLOOR ABOVE
REMOVE WOOD FLOOR INFILL ABOVE STAIR TO BE REMOVED
REMOVE ALL GYP WITH TEXTURED ORANGE PEEL FINISH, TYP.
REMOVE DOOR AND FRAME AND INFILL WITH CMU, TOOTH IN NEW CMU AND COAT EXTERIOR WITH WATERPROOFING
REMOVE EXISTING DOOR, FRAME TO REMAIN
REMOVE WINDOW, PREP OPENING FOR REPLACEMENT WINDOW
REMOVE EXISTING DOOR AND FRAME, PREP OPENING FOR NEW DOOR AND FRAME
REMOVE ROOF EDGE FLASHING, TPO OR EPDM AND ROOF INSULATION, REF MEP FOR ROOF EQUIPMENT DEMO REQUIREMENTS
REMOVE ALL FACADE CLADDING BACK TO STRUCTURE, SALVAGE BRICK FOR ANY PATCH WORK REQUIRED
REMOVE PORTION OF WALL ABOVE STOREFRONT
REMOVE LIGHTING, REF ELECT
REMOVE CANOPY FINISHES, SIGNAGE, AND SOFFIT VENTS
REMOVE EQUIPMENT VENT, PATCH W/ SALVAGED BRICK
GENERAL DEMO NOTES:
1. SALVAGE REMOVED DOORS AND FRAMES, REUSE AS INDICATED. INFORM ARCHITECT OF ANY CONFLICTS OR DISCREPANCIES W/ REUSING EXISTING DOORS AS SCHEDULED. (REF DOOR SCHEDULE)
2. PROTECT ALL EXISTING WORK THAT SURROUNDS THE SCOPE OF WORK, TYPICAL.3. DEMO PLANS SHOW APPROXIMATE SCOPE OF DEMO REQUIREMENTS -
REFERENCE PLANS, SECTIONS, ELEVATIONS, ETC. FOR EXTENT OF NEW CONSTRUCTION; DEMO AS REQUIRED AND NOTIFY ARCHITECT OF ANY DISCREPANCIES.
4. CONTRACTOR TO FIELD VERIFY ALL EXISTING CONDITIONS AND NOTIFY ARCHITECT OF ANY DISCREPANCIES.
5. ALL EXISTING LIGHTING TO BE REMOVED AND REPLACED WITH UPDATED FIXTURES. REF ELECTRICAL.
6. REMOVE ALL FLOOR FINISHES, CEILING GRID AND TILE, AND ABOVE CEILING MECH U.N.O.
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
SECOND FLOOR113' - 11"
B.O. DECK126' - 4"
ABC
8
11
10
20' - 0" 20' - 0" 13' - 8"
18
11' -
4"
4' -
8"
8' -
0"
5
29
5
5
20 20
CAREFULLY REMOVE BUILDING SIGNAGE AS TO NOT DAMAGE EXISTING BRICK FACADE
SECOND FLOOR113' - 11"
B.O. DECK126' - 4"
FIRST FLOORLEVEL - SOUTH
102' - 0"
A B C
13' - 8" 20' - 0"
11
29
8
5 5
SHEET TITLE
PROJECT NUMBER
SHEET NUMBER
A
B
C
D
54321
A
B
C
D
FILE
PA
TH:
DA
TE:
DR
AW
N B
Y:
54321
SUBMISSION DATES
500 north broadway suite 200oklahoma city, ok 73102phone: 405.231.3105
schwerdt design grouparchitecture interiors planning2231 sw wanamaker rd suite 303topeka, kansas 66614-4275phone: 785.273.7540
C:\U
sers
\Laure
n\D
ocu
ments
\190121 A
E C
orp
ora
te O
ffic
e (
GageC
ente
r)_ln
fLK
K7H
.rvt
8/6
/2019 2
:44:2
7 P
M
AD
VIS
OR
S E
XC
EL
-G
AG
E C
EN
TE
R C
AM
PU
S
PH
AS
E 1
-D
EM
O P
AC
KA
GE
TO
PE
KA
, KA
NS
AS
666
04
EXTERIOR DEMOELEVATIONS - BUILDING A
190121
D-202
Aut
hor
PROGRESS PRINT ONLY
SCALE: 1/8" = 1'-0"1 NORTH DEMO ELEVATION
SCALE: 1/8" = 1'-0"2 SOUTH DEMO ELEVATION
2019-08-06 16:45-05:00
23456
2932 32 32
PREP FOR NEW STOREFRONT
DEMO FACADESALVAGE BRICK FOR PATCHWORK
555
REF NEW CONSTRUCTION PLANS & ELEVATIONS
DEMO FACADESALVAGE BRICK FOR PATCHWORK AS REQUIRED
ELEVATIONS
DEMO FACADE; REFNEW CONSTRUCTION
32
RE
F S
TR
UC
TU
RA
L
DE
MO
AS
RE
QU
IRE
DF
OR
NE
W R
IBB
ON
ST
OR
EF
RO
NT
33 3333
30
5
2A-304
2 3 4 5 6
25' - 0" 25' - 0" 25' - 0" 25' - 0"
19
28
28
32 32 3229
DEMO NOTES
1REMOVE EXISTING PARTITION OR PORTION THERE OF AND ALL ASSOCIATED TO THE EXTENT REQUIRED FOR NEW SCOPE, PATCH ADJACENT GYP AS REQUIRED. REFERENCE NEW CONSTRUCTION PLANS, TYP.
REMOVE AND SALVAGE EXISTING DOOR, FRAME, TRIM AND HARDWARE ALONG WITH SIDELIGHT W.O. (UNO ON SCHEDULE) FOR REUSE; REF DOOR SCHEDULE AND NEW CONSTRUCTION PLANS FOR NEW LOCATION.
REMOVE EXISTING DOOR AND FRAME ALONG WITH SIDELITE W.O., INFILL WITH GYP AND STUD ASSEMBLY TO MATCH EXISTING PARTITION.
PREPARE ROUGH OPENING FOR NEW OR SALVAGED DOOR AND SIDELITE W.O., REF DOOR SCHEDULE AND NEW CONSTRUCTION PLANS.
CAREFULLY REMOVE EXISTING STOREFRONT, OR WINDOW, AS NOT TO DAMAGE EXISTING MASONRY FACADE.
REMOVE EXISTING MILLWORK AND COUNTERTOPS, CAP ELECTRICAL AND PLUMBING NOT TO BE USED; REF MEP
UNLESS OTHERWISE NOTED, THE DEMOLITION OF THE EXISTING AREA IDENTIFIED TO BE DEMOLISHED IS INTENDED TO BE A COMPLETE INTERIOR REMOVAL OF ALL EXISTING ARCHITECTURAL, MECHANICAL, ELECTRICAL AND PLUMBING COMPONENTS.
REMOVE EXTERIOR CANOPY AND ALL ASSOCIATED INCLUDING COLUMNS AND COLUMN FOUNDATIONS
REMOVE EXISTING DOOR AND FRAME, TO BE INFILLED WITH STOREFRONT GLAZING
DEMO DELIVERY DOCK AND EVERYTHING ON IT INCLUDING BUT NOT LIMITED TO, WALLS AND COOLERS INCLUDING ALL ASSOCIATED ELECTRICAL. WATERPROOF MAIN BUILDING FOUNDATION BEFORE BACKFILLING
REMOVE EXTERIOR SCREEN WALL AND ASSOCIATED FOOTING
REMOVE EXISTING HAND AND GUARDRAIL INCLUDING VERTICAL STEEL PICKETS BETWEEN SWITCHBACKS
REMOVE ALL PLUMBING FIXTURES AND PARTITIONS, CAP PLUMBING AND PATCH FLOOR AS REQUIRED; REF MEP AND NEW CONSTRUCTION PLANS
REMOVE WATER FOUNTAIN
REMOVE ALL FIXTURES AND HANDRAILS, CAP PLUMBING NOT TO BE USED, REF PLUMBING
STAIRS AND RAILINGS TO BE REMOVED AND FLOOR IS TO BE INFILLED, REF STRUCT IN NEW CONSTRUCTION PACKAGE
DEMO EXISTING WOOD LADDER, TO BE REPLACED WITH CODE COMPLIANT LADDER
DEMO CONCRETE SIDEWALK AND CURB, SAW CUT AROUND CANOPY COLUMNS TO REMAIN; PROVIDE $15,000 ALLOWANCE FOR POSSIBLE COLUMN FOUNDATION WORK
REMOVE EXTERIOR GUARDRAIL / HANDRAIL INCLUDING WIDE FLANGE STEEL POSTS W.O.
REMOVE RETAINING WALL AND LANDSCAPING ALONG WITH CONCRETE STAIR AND RAILING, PREP AREA FOR NEW WALL, SIDEWALKS AND LANDSCAPING
REMOVE EXISTING ASPHALT, CURB, INLETS, LIGHT POLES, FIRE HYDRANTS, ETC. AS REQUIRED IN DESIGNATED AREA AROUND BUILDING; REF CIVIL
PREPARE ROUGH OPENING FOR NEW STOREFRONT WINDOW; WINDOWS TO ALIGN WITH EXISTING OPENINGS ON SECOND FLOOR ABOVE
REMOVE WOOD FLOOR INFILL ABOVE STAIR TO BE REMOVED
REMOVE ALL GYP WITH TEXTURED ORANGE PEEL FINISH, TYP.
REMOVE DOOR AND FRAME AND INFILL WITH CMU, TOOTH IN NEW CMU AND COAT EXTERIOR WITH WATERPROOFING
REMOVE EXISTING DOOR, FRAME TO REMAIN
REMOVE WINDOW, PREP OPENING FOR REPLACEMENT WINDOW
REMOVE EXISTING DOOR AND FRAME, PREP OPENING FOR NEW DOOR AND FRAME
REMOVE ROOF EDGE FLASHING, TPO OR EPDM AND ROOF INSULATION, REF MEP FOR ROOF EQUIPMENT DEMO REQUIREMENTS
REMOVE ALL FACADE CLADDING BACK TO STRUCTURE, SALVAGE BRICK FOR ANY PATCH WORK REQUIRED
REMOVE PORTION OF WALL ABOVE STOREFRONT
REMOVE LIGHTING, REF ELECT
REMOVE CANOPY FINISHES, SIGNAGE, AND SOFFIT VENTS
REMOVE EQUIPMENT VENT, PATCH W/ SALVAGED BRICK
GENERAL DEMO NOTES:
1. SALVAGE REMOVED DOORS AND FRAMES, REUSE AS INDICATED. INFORM ARCHITECT OF ANY CONFLICTS OR DISCREPANCIES W/ REUSING EXISTING DOORS AS SCHEDULED. (REF DOOR SCHEDULE)
2. PROTECT ALL EXISTING WORK THAT SURROUNDS THE SCOPE OF WORK, TYPICAL.3. DEMO PLANS SHOW APPROXIMATE SCOPE OF DEMO REQUIREMENTS -
REFERENCE PLANS, SECTIONS, ELEVATIONS, ETC. FOR EXTENT OF NEW CONSTRUCTION; DEMO AS REQUIRED AND NOTIFY ARCHITECT OF ANY DISCREPANCIES.
4. CONTRACTOR TO FIELD VERIFY ALL EXISTING CONDITIONS AND NOTIFY ARCHITECT OF ANY DISCREPANCIES.
5. ALL EXISTING LIGHTING TO BE REMOVED AND REPLACED WITH UPDATED FIXTURES. REF ELECTRICAL.
6. REMOVE ALL FLOOR FINISHES, CEILING GRID AND TILE, AND ABOVE CEILING MECH U.N.O.
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
SHEET TITLE
PROJECT NUMBER
SHEET NUMBER
A
B
C
D
54321
A
B
C
D
FILE
PA
TH:
DA
TE:
DR
AW
N B
Y:
54321
SUBMISSION DATES
500 north broadway suite 200oklahoma city, ok 73102phone: 405.231.3105
schwerdt design grouparchitecture interiors planning2231 sw wanamaker rd suite 303topeka, kansas 66614-4275phone: 785.273.7540
C:\U
sers
\Laure
n\D
ocu
ments
\190121 A
E C
orp
ora
te O
ffic
e (
GageC
ente
r)_ln
fLK
K7H
.rvt
8/6
/2019 2
:44:2
9 P
M
AD
VIS
OR
S E
XC
EL
-G
AG
E C
EN
TE
R C
AM
PU
S
PH
AS
E 1
-D
EM
O P
AC
KA
GE
TO
PE
KA
, KA
NS
AS
666
04
EXTERIOR DEMOELEVATIONS - BUILDING K
190121
D-203
Aut
hor
PROGRESS PRINT ONLY
SCALE: 1/8" = 1'-0"1 COBBLESTONE DEMO NORTH ELEVATION
SCALE: 1/8" = 1'-0"2 COBBLESTONE DEMO SOUTH ELEVATION
2019-08-06 16:43-05:00
ABCDE
23' - 0" 23' - 0" 23' - 0"29
22 2222
A B C D E
29
22 22 22
19
DEMO EQUIPMENT PLATFORM, REF MEP FOR EQUIPMETN REQUIREMENTS
3232
DEMO NOTES
1REMOVE EXISTING PARTITION OR PORTION THERE OF AND ALL ASSOCIATED TO THE EXTENT REQUIRED FOR NEW SCOPE, PATCH ADJACENT GYP AS REQUIRED. REFERENCE NEW CONSTRUCTION PLANS, TYP.
REMOVE AND SALVAGE EXISTING DOOR, FRAME, TRIM AND HARDWARE ALONG WITH SIDELIGHT W.O. (UNO ON SCHEDULE) FOR REUSE; REF DOOR SCHEDULE AND NEW CONSTRUCTION PLANS FOR NEW LOCATION.
REMOVE EXISTING DOOR AND FRAME ALONG WITH SIDELITE W.O., INFILL WITH GYP AND STUD ASSEMBLY TO MATCH EXISTING PARTITION.
PREPARE ROUGH OPENING FOR NEW OR SALVAGED DOOR AND SIDELITE W.O., REF DOOR SCHEDULE AND NEW CONSTRUCTION PLANS.
CAREFULLY REMOVE EXISTING STOREFRONT, OR WINDOW, AS NOT TO DAMAGE EXISTING MASONRY FACADE.
REMOVE EXISTING MILLWORK AND COUNTERTOPS, CAP ELECTRICAL AND PLUMBING NOT TO BE USED; REF MEP
UNLESS OTHERWISE NOTED, THE DEMOLITION OF THE EXISTING AREA IDENTIFIED TO BE DEMOLISHED IS INTENDED TO BE A COMPLETE INTERIOR REMOVAL OF ALL EXISTING ARCHITECTURAL, MECHANICAL, ELECTRICAL AND PLUMBING COMPONENTS.
REMOVE EXTERIOR CANOPY AND ALL ASSOCIATED INCLUDING COLUMNS AND COLUMN FOUNDATIONS
REMOVE EXISTING DOOR AND FRAME, TO BE INFILLED WITH STOREFRONT GLAZING
DEMO DELIVERY DOCK AND EVERYTHING ON IT INCLUDING BUT NOT LIMITED TO, WALLS AND COOLERS INCLUDING ALL ASSOCIATED ELECTRICAL. WATERPROOF MAIN BUILDING FOUNDATION BEFORE BACKFILLING
REMOVE EXTERIOR SCREEN WALL AND ASSOCIATED FOOTING
REMOVE EXISTING HAND AND GUARDRAIL INCLUDING VERTICAL STEEL PICKETS BETWEEN SWITCHBACKS
REMOVE ALL PLUMBING FIXTURES AND PARTITIONS, CAP PLUMBING AND PATCH FLOOR AS REQUIRED; REF MEP AND NEW CONSTRUCTION PLANS
REMOVE WATER FOUNTAIN
REMOVE ALL FIXTURES AND HANDRAILS, CAP PLUMBING NOT TO BE USED, REF PLUMBING
STAIRS AND RAILINGS TO BE REMOVED AND FLOOR IS TO BE INFILLED, REF STRUCT IN NEW CONSTRUCTION PACKAGE
DEMO EXISTING WOOD LADDER, TO BE REPLACED WITH CODE COMPLIANT LADDER
DEMO CONCRETE SIDEWALK AND CURB, SAW CUT AROUND CANOPY COLUMNS TO REMAIN; PROVIDE $15,000 ALLOWANCE FOR POSSIBLE COLUMN FOUNDATION WORK
REMOVE EXTERIOR GUARDRAIL / HANDRAIL INCLUDING WIDE FLANGE STEEL POSTS W.O.
REMOVE RETAINING WALL AND LANDSCAPING ALONG WITH CONCRETE STAIR AND RAILING, PREP AREA FOR NEW WALL, SIDEWALKS AND LANDSCAPING
REMOVE EXISTING ASPHALT, CURB, INLETS, LIGHT POLES, FIRE HYDRANTS, ETC. AS REQUIRED IN DESIGNATED AREA AROUND BUILDING; REF CIVIL
PREPARE ROUGH OPENING FOR NEW STOREFRONT WINDOW; WINDOWS TO ALIGN WITH EXISTING OPENINGS ON SECOND FLOOR ABOVE
REMOVE WOOD FLOOR INFILL ABOVE STAIR TO BE REMOVED
REMOVE ALL GYP WITH TEXTURED ORANGE PEEL FINISH, TYP.
REMOVE DOOR AND FRAME AND INFILL WITH CMU, TOOTH IN NEW CMU AND COAT EXTERIOR WITH WATERPROOFING
REMOVE EXISTING DOOR, FRAME TO REMAIN
REMOVE WINDOW, PREP OPENING FOR REPLACEMENT WINDOW
REMOVE EXISTING DOOR AND FRAME, PREP OPENING FOR NEW DOOR AND FRAME
REMOVE ROOF EDGE FLASHING, TPO OR EPDM AND ROOF INSULATION, REF MEP FOR ROOF EQUIPMENT DEMO REQUIREMENTS
REMOVE ALL FACADE CLADDING BACK TO STRUCTURE, SALVAGE BRICK FOR ANY PATCH WORK REQUIRED
REMOVE PORTION OF WALL ABOVE STOREFRONT
REMOVE LIGHTING, REF ELECT
REMOVE CANOPY FINISHES, SIGNAGE, AND SOFFIT VENTS
REMOVE EQUIPMENT VENT, PATCH W/ SALVAGED BRICK
GENERAL DEMO NOTES:
1. SALVAGE REMOVED DOORS AND FRAMES, REUSE AS INDICATED. INFORM ARCHITECT OF ANY CONFLICTS OR DISCREPANCIES W/ REUSING EXISTING DOORS AS SCHEDULED. (REF DOOR SCHEDULE)
2. PROTECT ALL EXISTING WORK THAT SURROUNDS THE SCOPE OF WORK, TYPICAL.3. DEMO PLANS SHOW APPROXIMATE SCOPE OF DEMO REQUIREMENTS -
REFERENCE PLANS, SECTIONS, ELEVATIONS, ETC. FOR EXTENT OF NEW CONSTRUCTION; DEMO AS REQUIRED AND NOTIFY ARCHITECT OF ANY DISCREPANCIES.
4. CONTRACTOR TO FIELD VERIFY ALL EXISTING CONDITIONS AND NOTIFY ARCHITECT OF ANY DISCREPANCIES.
5. ALL EXISTING LIGHTING TO BE REMOVED AND REPLACED WITH UPDATED FIXTURES. REF ELECTRICAL.
6. REMOVE ALL FLOOR FINISHES, CEILING GRID AND TILE, AND ABOVE CEILING MECH U.N.O.
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34 SHEET TITLE
PROJECT NUMBER
SHEET NUMBER
A
B
C
D
54321
A
B
C
D
FILE
PA
TH:
DA
TE:
DR
AW
N B
Y:
54321
SUBMISSION DATES
500 north broadway suite 200oklahoma city, ok 73102phone: 405.231.3105
schwerdt design grouparchitecture interiors planning2231 sw wanamaker rd suite 303topeka, kansas 66614-4275phone: 785.273.7540
C:\U
sers
\Laure
n\D
ocu
ments
\190121 A
E C
orp
ora
te O
ffic
e (
GageC
ente
r)_ln
fLK
K7H
.rvt
8/6
/2019 2
:44:3
0 P
M
AD
VIS
OR
S E
XC
EL
-G
AG
E C
EN
TE
R C
AM
PU
S
PH
AS
E 1
-D
EM
O P
AC
KA
GE
TO
PE
KA
, KA
NS
AS
666
04
EXTERIOR DEMOELEVATIONS - BUILDING K
190121
D-204
Aut
hor
PROGRESS PRINT ONLY
SCALE: 1/8" = 1'-0"1 COBBLESTONE DEMO EAST ELEVATION
SCALE: 1/8" = 1'-0"2 COBBLESTONE DEMO WEST ELEVATION
2019-08-06 16:46-05:00
WH
WH
WH
1 3 4 5 6 7 8 9
A
B
C
1.5
2
1 MECHANICAL/ELECTRICAL1/8"=1'-0"BUILDING A - LOWER LEVEL DEMOLITION PLAN
.NORTH SHEET TITLE
PROJECT NUMBER
SHEET NUMBER
schwerdt design grouparchitecture interiors planning2231 sw wanamaker rd suite 303
A
B
C
D
54321
A
B
C
D
54321
topeka, kansas 66614-4275phone: 785.273.7540fax: 785.273.7579500 north broadway suite 200oklahoma city, ok 73102phone: 405.231.3105fax: 405.231.3115
SUBMISSION DATES08-06-19
3639 SW Summerfield Drive, Suite A
Telephone: (785) 233-3232
Latimer Sommers& Associates, P.A.
C O N S U L T I N G E N G I N E E R S
Topeka, Kansas 66614-3974
FAX: (785) 233-0647Email: [email protected]
LSA PROJECT NO. 1908004
ADVI
SORS
EXC
EL - G
AGE
CENT
ER C
AMPU
SPH
ASE
1 - R
EMOD
ELTO
PEKA
, KAN
SAS
6660
4
190121
BUILDING A - LOWER LEVELDEMOLITION PLAN -
MECHANICAL/ELECTRICAL
ME-201
DN
DN
DN
1 3 4 5 6 7 8 9
A
B
C
1.5 2
1 MECHANICAL/ELECTRICAL1/8"=1'-0"BUILDING A - FIRST FLOOR DEMOLITION PLAN
.NORTH
SHEET TITLE
PROJECT NUMBER
SHEET NUMBER
schwerdt design grouparchitecture interiors planning2231 sw wanamaker rd suite 303
A
B
C
D
54321
A
B
C
D
54321
topeka, kansas 66614-4275phone: 785.273.7540fax: 785.273.7579500 north broadway suite 200oklahoma city, ok 73102phone: 405.231.3105fax: 405.231.3115
SUBMISSION DATES08-06-19
3639 SW Summerfield Drive, Suite A
Telephone: (785) 233-3232
Latimer Sommers& Associates, P.A.
C O N S U L T I N G E N G I N E E R S
Topeka, Kansas 66614-3974
FAX: (785) 233-0647Email: [email protected]
LSA PROJECT NO. 1908004
ADVI
SORS
EXC
EL - G
AGE
CENT
ER C
AMPU
SPH
ASE
1 - R
EMOD
ELTO
PEKA
, KAN
SAS
6660
4
190121
BUILDING A - FIRST FLOORDEMOLITION PLAN -
MECHANICAL/ELECTRICAL
ME-202
1 3 4 5 6 7 8 9
A
B
C
1.5
2
1 MECHANICAL/ELECTRICAL1/8"=1'-0"BUILDING A - SECOND FLOOR DEMOLITION PLAN
.NORTH
SHEET TITLE
PROJECT NUMBER
SHEET NUMBER
schwerdt design grouparchitecture interiors planning2231 sw wanamaker rd suite 303
A
B
C
D
54321
A
B
C
D
54321
topeka, kansas 66614-4275phone: 785.273.7540fax: 785.273.7579500 north broadway suite 200oklahoma city, ok 73102phone: 405.231.3105fax: 405.231.3115
SUBMISSION DATES08-06-19
3639 SW Summerfield Drive, Suite A
Telephone: (785) 233-3232
Latimer Sommers& Associates, P.A.
C O N S U L T I N G E N G I N E E R S
Topeka, Kansas 66614-3974
FAX: (785) 233-0647Email: [email protected]
LSA PROJECT NO. 1908004
ADVI
SORS
EXC
EL - G
AGE
CENT
ER C
AMPU
SPH
ASE
1 - R
EMOD
ELTO
PEKA
, KAN
SAS
6660
4
190121
BUILDING A - SECONDFLOOR DEMOLITION PLAN -MECHANICAL/ELECTRICAL
ME-203
1 MECHANICAL/ELECTRICAL1/8"=1'-0"BUILDING A - ROOFTOP DEMOLITION PLAN
.NORTH
1 3 4 5 6 7 8 9
A
B
C
1.5 2
SHEET TITLE
PROJECT NUMBER
SHEET NUMBER
schwerdt design grouparchitecture interiors planning2231 sw wanamaker rd suite 303
A
B
C
D
54321
A
B
C
D
54321
topeka, kansas 66614-4275phone: 785.273.7540fax: 785.273.7579500 north broadway suite 200oklahoma city, ok 73102phone: 405.231.3105fax: 405.231.3115
SUBMISSION DATES08-06-19
3639 SW Summerfield Drive, Suite A
Telephone: (785) 233-3232
Latimer Sommers& Associates, P.A.
C O N S U L T I N G E N G I N E E R S
Topeka, Kansas 66614-3974
FAX: (785) 233-0647Email: [email protected]
LSA PROJECT NO. 1908004
ADVI
SORS
EXC
EL - G
AGE
CENT
ER C
AMPU
SPH
ASE
1 - R
EMOD
ELTO
PEKA
, KAN
SAS
6660
4
190121
BUILDING A - ROOFTOPDEMOLITION PLAN -
MECHANICAL/ELECTRICAL
ME-204
1 MECHANICAL/ELECTRICAL1/8"=1'-0"BUILDING K - FIRST FLOOR DEMOLITION PLAN
.
UP
A
B
C
D
E
2 3 4 5 6
NORTH
SHEET TITLE
PROJECT NUMBER
SHEET NUMBER
schwerdt design grouparchitecture interiors planning2231 sw wanamaker rd suite 303
A
B
C
D
54321
A
B
C
D
54321
topeka, kansas 66614-4275phone: 785.273.7540fax: 785.273.7579500 north broadway suite 200oklahoma city, ok 73102phone: 405.231.3105fax: 405.231.3115
SUBMISSION DATES08-06-19
3639 SW Summerfield Drive, Suite A
Telephone: (785) 233-3232
Latimer Sommers& Associates, P.A.
C O N S U L T I N G E N G I N E E R S
Topeka, Kansas 66614-3974
FAX: (785) 233-0647Email: [email protected]
LSA PROJECT NO. 1908004
ADVI
SORS
EXC
EL - G
AGE
CENT
ER C
AMPU
SPH
ASE
1 - R
EMOD
ELTO
PEKA
, KAN
SAS
6660
4
190121
BUILDING K - FIRST FLOORDEMOLITION PLAN -
MECHANICAL/ELECTRICAL
ME-205
1 MECHANICAL/ELECTRICAL1/8"=1'-0"BUILDING K - SECOND FLOOR DEMOLITION PLAN
.
UP
NORTH
SHEET TITLE
PROJECT NUMBER
SHEET NUMBER
schwerdt design grouparchitecture interiors planning2231 sw wanamaker rd suite 303
A
B
C
D
54321
A
B
C
D
54321
topeka, kansas 66614-4275phone: 785.273.7540fax: 785.273.7579500 north broadway suite 200oklahoma city, ok 73102phone: 405.231.3105fax: 405.231.3115
SUBMISSION DATES08-06-19
3639 SW Summerfield Drive, Suite A
Telephone: (785) 233-3232
Latimer Sommers& Associates, P.A.
C O N S U L T I N G E N G I N E E R S
Topeka, Kansas 66614-3974
FAX: (785) 233-0647Email: [email protected]
LSA PROJECT NO. 1908004
ADVI
SORS
EXC
EL - G
AGE
CENT
ER C
AMPU
SPH
ASE
1 - R
EMOD
ELTO
PEKA
, KAN
SAS
6660
4
190121
BUILDING K - SECONDFLOOR DEMOLITION PLAN -MECHANICAL/ELECTRICAL
ME-206
